From f76e4720e76eb6868b728e4f7ab2c42596661fa7 Mon Sep 17 00:00:00 2001 From: Paolo Bonzini Date: Wed, 5 Apr 2017 13:41:15 +0200 Subject: [PATCH] iTCO_wdt: all versions count down twice The ICH9 is listed as having TCO v2, and indeed the behavior in the datasheet corresponds to v2 (for example the NO_REBOOT flag is accessible via the 16KiB-aligned Root Complex Base Address). However, the TCO counts twice just like in v1; the documentation of the SECOND_TO_STS bit says: "ICH9 sets this bit to 1 to indicate that the TIMEOUT bit had been (or is currently) set and a second timeout occurred before the TCO_RLD register was written. If this bit is set and the NO_REBOOT config bit is 0, then the ICH9 will reboot the system after the second timeout. The same can be found in the BayTrail (Atom E3800) datasheet, and even HOWTOs around the Internet say that it will reboot after _twice_ the specified heartbeat. I did not find the Apollo Lake datasheet, but because v4/v5 has a SECOND_TO_STS bit just like the previous version I'm enabling this for Apollo Lake as well. Cc: linux-watchdog@vger.kernel.org Reviewed-by: Andy Shevchenko Signed-off-by: Paolo Bonzini Reviewed-by: Guenter Roeck Signed-off-by: Guenter Roeck Signed-off-by: Wim Van Sebroeck --- .../watchdog/watchdog-parameters.txt | 2 +- drivers/watchdog/iTCO_wdt.c | 22 +++++++++---------- 2 files changed, 11 insertions(+), 13 deletions(-) diff --git a/Documentation/watchdog/watchdog-parameters.txt b/Documentation/watchdog/watchdog-parameters.txt index 4f7d86dd0a5d8..914518aeb9728 100644 --- a/Documentation/watchdog/watchdog-parameters.txt +++ b/Documentation/watchdog/watchdog-parameters.txt @@ -117,7 +117,7 @@ nowayout: Watchdog cannot be stopped once started ------------------------------------------------- iTCO_wdt: heartbeat: Watchdog heartbeat in seconds. - (2smi_res, wd_dev->timeout); + /* Reset the timeout status bit so that the timer + * needs to count down twice again before rebooting */ + outw(0x0008, TCO1_STS(p)); /* write 1 to clear bit */ + /* Reload the timer by writing to the TCO Timer Counter register */ - if (p->iTCO_version >= 2) { + if (p->iTCO_version >= 2) outw(0x01, TCO_RLD(p)); - } else if (p->iTCO_version == 1) { - /* Reset the timeout status bit so that the timer - * needs to count down twice again before rebooting */ - outw(0x0008, TCO1_STS(p)); /* write 1 to clear bit */ - + else if (p->iTCO_version == 1) outb(0x01, TCO_RLD(p)); - } spin_unlock(&p->io_lock); return 0; @@ -328,11 +327,8 @@ static int iTCO_wdt_set_timeout(struct watchdog_device *wd_dev, unsigned int t) unsigned char val8; unsigned int tmrval; - tmrval = seconds_to_ticks(p, t); - - /* For TCO v1 the timer counts down twice before rebooting */ - if (p->iTCO_version == 1) - tmrval /= 2; + /* The timer counts down twice before rebooting */ + tmrval = seconds_to_ticks(p, t) / 2; /* from the specs: */ /* "Values of 0h-3h are ignored and should not be attempted" */ @@ -385,6 +381,8 @@ static unsigned int iTCO_wdt_get_timeleft(struct watchdog_device *wd_dev) spin_lock(&p->io_lock); val16 = inw(TCO_RLD(p)); val16 &= 0x3ff; + if (!(inw(TCO1_STS(p)) & 0x0008)) + val16 += (inw(TCOv2_TMR(p)) & 0x3ff); spin_unlock(&p->io_lock); time_left = ticks_to_seconds(p, val16); -- 2.39.5