tx timeout and slot time are currently specified in units of HZ. On
Alpha, HZ is defined as 1024. When building alpha:allmodconfig, this
results in the following error message.
drivers/net/hamradio/6pack.c: In function 'sixpack_open':
drivers/net/hamradio/6pack.c:71:41: error:
unsigned conversion from 'int' to 'unsigned char'
changes value from '256' to '0'
In the 6PACK protocol, tx timeout is specified in units of 10 ms and
transmitted over the wire:
https://www.linux-ax25.org/wiki/6PACK
Defining a value dependent on HZ doesn't really make sense, and
presumably comes from the (very historical) situation where HZ was
originally 100.
Note that the SIXP_SLOTTIME use explicitly is about 10ms granularity:
drm/rockchip: cdn-dp-core: Make cdn_dp_core_resume __maybe_unused
With the new static annotation, the compiler warns when the functions
are actually unused:
drivers/gpu/drm/rockchip/cdn-dp-core.c:1123:12: error: 'cdn_dp_resume' defined but not used [-Werror=unused-function]
1123 | static int cdn_dp_resume(struct device *dev)
| ^~~~~~~~~~~~~
Mark them __maybe_unused to suppress that warning as well.
[ Not so 'new' static annotations any more, and I removed the part of
the patch that added __maybe_unused to cdn_dp_suspend(), because it's
used by the shutdown/remove code.
So only the resume function ends up possibly unused if CONFIG_PM isn't
set - Linus ]
alpha: Declare virt_to_phys and virt_to_bus parameter as pointer to volatile
Some drivers pass a pointer to volatile data to virt_to_bus() and
virt_to_phys(), and that works fine. One exception is alpha. This
results in a number of compile errors such as
drivers/net/wan/lmc/lmc_main.c: In function 'lmc_softreset':
drivers/net/wan/lmc/lmc_main.c:1782:50: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
drivers/atm/ambassador.c: In function 'do_loader_command':
drivers/atm/ambassador.c:1747:58: error:
passing argument 1 of 'virt_to_bus' discards 'volatile'
qualifier from pointer target type
Declare the parameter of virt_to_phys and virt_to_bus as pointer to
volatile to fix the problem.
3com 3c515: make it compile on 64-bit architectures
This driver isn't enabled most places because of the ISA config
dependency, but alpha still has it. And I think the 'Jensen' actually
did have an ISA slot.
However, it doesn't build cleanly, because the "Vortex bus master" code
just casts the skb->data pointer to 'int':
outl((int) (skb->data), ioaddr + Wn7_MasterAddr);
which is all kinds of broken. Even on a good old traditional PC/AT it
would be broken because the high bits will be random kernel address
bits, but presumably the hardware ignores those bits. I mean, it's ISA.
We're talking 16MB dma limits. The "good old days".
Make the build happy with this kind of craziness by using the proper
isa_virt_to_bus() handling that the full bus master code uses anyway
(the Vortex bus mastering is a limited special case).
Merge tag 'm68k-for-v5.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
- Warning fixes to mitigate CONFIG_WERROR=y
* tag 'm68k-for-v5.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: mvme: Remove overdue #warnings in RTC handling
m68k: Double cast io functions to unsigned long
David Thompson [Wed, 15 Sep 2021 18:08:48 +0000 (14:08 -0400)]
mlxbf_gige: clear valid_polarity upon open
The network interface managed by the mlxbf_gige driver can
get into a problem state where traffic does not flow.
In this state, the interface will be up and enabled, but
will stop processing received packets. This problem state
will happen if three specific conditions occur:
1) driver has received more than (N * RxRingSize) packets but
less than (N+1 * RxRingSize) packets, where N is an odd number
Note: the command "ethtool -g <interface>" will display the
current receive ring size, which currently defaults to 128
2) the driver's interface was disabled via "ifconfig oob_net0 down"
during the window described in #1.
3) the driver's interface is re-enabled via "ifconfig oob_net0 up"
This patch ensures that the driver's "valid_polarity" field is
cleared during the open() method so that it always matches the
receive polarity used by hardware. Without this fix, the driver
needs to be unloaded and reloaded to correct this problem state.
Fixes: f92e1869d74e ("Add Mellanox BlueField Gigabit Ethernet driver") Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com> Signed-off-by: David Thompson <davthompson@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 15 Sep 2021 17:19:07 +0000 (10:19 -0700)]
igc: fix tunnel offloading
Checking tunnel offloading, it turns out that offloading doesn't work
as expected. The following script allows to reproduce the issue.
Call it as `testscript DEVICE LOCALIP REMOTEIP NETMASK'
=== SNIP ===
if [ $# -ne 4 ]
then
echo "Usage $0 DEVICE LOCALIP REMOTEIP NETMASK"
exit 1
fi
DEVICE="$1"
LOCAL_ADDRESS="$2"
REMOTE_ADDRESS="$3"
NWMASK="$4"
echo "Driver: $(ethtool -i ${DEVICE} | awk '/^driver:/{print $2}') "
ethtool -k "${DEVICE}" | grep tx-udp
echo
echo "Set up NIC and tunnel..."
ip addr add "${LOCAL_ADDRESS}/${NWMASK}" dev "${DEVICE}"
ip link set "${DEVICE}" up
sleep 2
ip link add vxlan1 type vxlan id 42 \
remote "${REMOTE_ADDRESS}" \
local "${LOCAL_ADDRESS}" \
dstport 0 \
dev "${DEVICE}"
ip addr add fc00::1/64 dev vxlan1
ip link set vxlan1 up
sleep 2
rm -f vxlan.pcap
echo "Running tcpdump and iperf3..."
( nohup tcpdump -i any -w vxlan.pcap >/dev/null 2>&1 ) &
sleep 2
iperf3 -c fc00::2 >/dev/null
pkill tcpdump
echo
echo -n "Max. Paket Size: "
tcpdump -r vxlan.pcap -nnle 2>/dev/null \
| grep "${LOCAL_ADDRESS}.*> ${REMOTE_ADDRESS}.*OTV" \
| awk '{print $8}' | awk -F ':' '{print $1}' \
| sort -n | tail -1
echo
ip link del vxlan1
ip addr del ${LOCAL_ADDRESS}/${NWMASK} dev "${DEVICE}"
=== SNAP ===
The expected outcome is
Max. Paket Size: 64904
This is what you see on igb, the code igc has been taken from.
However, on igc the output is
Max. Paket Size: 1516
so the GSO aggregate packets are segmented by the kernel before calling
igc_xmit_frame. Inside the subsequent call to igc_tso, the check for
skb_is_gso(skb) fails and the function returns prematurely.
It turns out that this occurs because the feature flags aren't set
entirely correctly in igc_probe. In contrast to the original code
from igb_probe, igc_probe neglects to set the flags required to allow
tunnel offloading.
Setting the same flags as igb fixes the issue on igc.
Fixes: 34428dff3679 ("igc: Add GSO partial support") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Tested-by: Corinna Vinschen <vinschen@redhat.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the assert from the callback priv lookup function since it does
not require RTNL lock and is already protected by flow_indr_block_lock.
This will avoid warnings from being emitted to dmesg if the driver
registers its callback after an ingress qdisc was created for a
netdevice.
The warnings started after the following patch was merged:
commit 74fc4f828769 ("net: Fix offloading indirect devices dependency on qdisc order creation")
Signed-off-by: Eli Cohen <elic@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'hyperv-fixes-signed-20210915' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Fix kernel crash caused by uio driver (Vitaly Kuznetsov)
- Remove on-stack cpumask from HV APIC code (Wei Liu)
* tag 'hyperv-fixes-signed-20210915' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: remove on-stack cpumask from hv_send_ipi_mask_allbutself
asm-generic/hyperv: provide cpumask_to_vpset_noself
Drivers: hv: vmbus: Fix kernel crash upon unbinding a device from uio_hv_generic driver
Merge tag 'rtc-5.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fix from Alexandre Belloni:
"Fix a locking issue in the cmos rtc driver"
* tag 'rtc-5.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: cmos: Disable irq around direct invocation of cmos_interrupt()
Vladimir Oltean [Tue, 14 Sep 2021 13:47:26 +0000 (16:47 +0300)]
net: dsa: flush switchdev workqueue before tearing down CPU/DSA ports
Sometimes when unbinding the mv88e6xxx driver on Turris MOX, these error
messages appear:
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete be:79:b4:9e:9e:96 vid 0 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 100 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 1 from fdb: -2
mv88e6085 d0032004.mdio-mii:12: port 1 failed to delete d8:58:d7:00:ca:6d vid 0 from fdb: -2
(and similarly for other ports)
What happens is that DSA has a policy "even if there are bugs, let's at
least not leak memory" and dsa_port_teardown() clears the dp->fdbs and
dp->mdbs lists, which are supposed to be empty.
But deleting that cleanup code, the warnings go away.
=> the FDB and MDB lists (used for refcounting on shared ports, aka CPU
and DSA ports) will eventually be empty, but are not empty by the time
we tear down those ports. Aka we are deleting them too soon.
The addresses that DSA complains about are host-trapped addresses: the
local addresses of the ports, and the MAC address of the bridge device.
The problem is that offloading those entries happens from a deferred
work item scheduled by the SWITCHDEV_FDB_DEL_TO_DEVICE handler, and this
races with the teardown of the CPU and DSA ports where the refcounting
is kept.
In fact, not only it races, but fundamentally speaking, if we iterate
through the port list linearly, we might end up tearing down the shared
ports even before we delete a DSA user port which has a bridge upper.
So as it turns out, we need to first tear down the user ports (and the
unused ones, for no better place of doing that), then the shared ports
(the CPU and DSA ports). In between, we need to ensure that all work
items scheduled by our switchdev handlers (which only run for user
ports, hence the reason why we tear them down first) have finished.
Fixes: 161ca59d39e9 ("net: dsa: reference count the MDB entries at the cross-chip notifier level") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20210914134726.2305133-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 14 Sep 2021 14:05:15 +0000 (17:05 +0300)]
Revert "net: phy: Uniform PHY driver access"
This reverts commit 3ac8eed62596387214869319379c1fcba264d8c6, which did
more than it said on the box, and not only it replaced to_phy_driver
with phydev->drv, but it also removed the "!drv" check, without actually
explaining why that is fine.
That patch in fact breaks suspend/resume on any system which has PHY
devices with no drivers bound.
The stack trace is:
Unable to handle kernel NULL pointer dereference at virtual address 00000000000000e8
pc : mdio_bus_phy_suspend+0xd8/0xec
lr : dpm_run_callback+0x38/0x90
Call trace:
mdio_bus_phy_suspend+0xd8/0xec
dpm_run_callback+0x38/0x90
__device_suspend+0x108/0x3cc
dpm_suspend+0x140/0x210
dpm_suspend_start+0x7c/0xa0
suspend_devices_and_enter+0x13c/0x540
pm_suspend+0x2a4/0x330
Examples why that assumption is not fine:
- There is an MDIO bus with a PHY device that doesn't have a specific
PHY driver loaded, because mdiobus_register() automatically creates a
PHY device for it but there is no specific PHY driver in the system.
Normally under those circumstances, the generic PHY driver will be
bound lazily to it (at phy_attach_direct time). But some Ethernet
drivers attach to their PHY at .ndo_open time. Until then it, the
to-be-driven-by-genphy PHY device will not have a driver. The blamed
patch amounts to saying "you need to open all net devices before the
system can suspend, to avoid the NULL pointer dereference".
- There is any raw MDIO device which has 'plausible' values in the PHY
ID registers 2 and 3, which is located on an MDIO bus whose driver
does not set bus->phy_mask = ~0 (which prevents auto-scanning of PHY
devices). An example could be a MAC's internal MDIO bus with PCS
devices on it, for serial links such as SGMII. PHY devices will get
created for those PCSes too, due to that MDIO bus auto-scanning, and
although those PHY devices are not used, they do not bother anybody
either. PCS devices are usually managed in Linux as raw MDIO devices.
Nonetheless, they do not have a PHY driver, nor does anybody attempt
to connect to them (because they are not a PHY), and therefore this
patch breaks that.
The goal itself of the patch is questionable, so I am going for a
straight revert. to_phy_driver does not seem to have a need to be
replaced by phydev->drv, in fact that might even trigger code paths
which were not given too deep of a thought.
For instance:
phy_probe populates phydev->drv at the beginning, but does not clean it
up on any error (including EPROBE_DEFER). So if the phydev driver
requests probe deferral, phydev->drv will remain populated despite there
being no driver bound.
If a system suspend starts in between the initial probe deferral request
and the subsequent probe retry, we will be calling the phydev->drv->suspend
method, but _before_ any phydev->drv->probe call has succeeded.
That is to say, if the phydev->drv is allocating any driver-private data
structure in ->probe, it pretty much expects that data structure to be
available in ->suspend. But it may not. That is a pretty insane
environment to present to PHY drivers.
In the code structure before the blamed patch, mdio_bus_phy_may_suspend
would just say "no, don't suspend" to any PHY device which does not have
a driver pointer _in_the_device_structure_ (not the phydev->drv). That
would essentially ensure that ->suspend will never get called for a
device that has not yet successfully completed probe. This is the code
structure the patch is returning to, via the revert.
Vladimir Oltean [Tue, 14 Sep 2021 13:43:31 +0000 (16:43 +0300)]
net: dsa: destroy the phylink instance on any error in dsa_slave_phy_setup
DSA supports connecting to a phy-handle, and has a fallback to a non-OF
based method of connecting to an internal PHY on the switch's own MDIO
bus, if no phy-handle and no fixed-link nodes were present.
The -ENODEV error code from the first attempt (phylink_of_phy_connect)
is what triggers the second attempt (phylink_connect_phy).
However, when the first attempt returns a different error code than
-ENODEV, this results in an unbalance of calls to phylink_create and
phylink_destroy by the time we exit the function. The phylink instance
has leaked.
There are many other error codes that can be returned by
phylink_of_phy_connect. For example, phylink_validate returns -EINVAL.
So this is a practical issue too.
Fixes: aab9c4067d23 ("net: dsa: Plug in PHYLINK support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20210914134331.2303380-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The qnx4 directory entries are 64-byte blocks that have different
contents depending on the a status byte that is in the last byte of the
block.
In particular, a directory entry can be either a "link info" entry with
a 48-byte name and pointers to the real inode information, or an "inode
entry" with a smaller 16-byte name and the full inode information.
But the code was written to always just treat the directory name as if
it was part of that "inode entry", and just extend the name to the
longer case if the status byte said it was a link entry.
That work just fine and gives the right results, but now that gcc is
tracking data structure accesses much more, the code can trigger a
compiler error about using up to 48 bytes (the long name) in a structure
that only has that shorter name in it:
fs/qnx4/dir.c: In function ‘qnx4_readdir’:
fs/qnx4/dir.c:51:32: error: ‘strnlen’ specified bound 48 exceeds source size 16 [-Werror=stringop-overread]
51 | size = strnlen(de->di_fname, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from fs/qnx4/qnx4.h:3,
from fs/qnx4/dir.c:16:
include/uapi/linux/qnx4_fs.h:45:25: note: source object declared here
45 | char di_fname[QNX4_SHORT_NAME_MAX];
| ^~~~~~~~
which is because the source code doesn't really make this whole "one of
two different types" explicit.
Fix this by introducing a very explicit union of the two types, and
basically explaining to the compiler what is really going on.
The sparc mdesc code does pointer games with 'struct mdesc_hdr', but
didn't describe to the compiler how that header is then followed by the
data that the header describes.
As a result, gcc is now unhappy since it does stricter pointer range
tracking, and doesn't understand about how these things work. This
results in various errors like:
arch/sparc/kernel/mdesc.c: In function ‘mdesc_node_by_name’:
arch/sparc/kernel/mdesc.c:647:22: error: ‘strcmp’ reading 1 or more bytes from a region of size 0 [-Werror=stringop-overread]
647 | if (!strcmp(names + ep[ret].name_offset, name))
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
which are easily avoided by just describing 'struct mdesc_hdr' better,
and making the node_block() helper function look into that unsized
data[] that follows the header.
This makes the sparc64 build happy again at least for my cross-compiler
version (gcc version 11.2.1).
Merge branch 'absolute-pointer' (patches from Guenter)
Merge absolute_pointer macro series from Guenter Roeck:
"Kernel test builds currently fail for several architectures with error
messages such as the following.
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0
[-Werror=stringop-overread]
Such warnings may be reported by gcc 11.x for string and memory
operations on fixed addresses if gcc's builtin functions are used for
those operations.
This series introduces absolute_pointer() to fix the problem.
absolute_pointer() disassociates a pointer from its originating symbol
type and context, and thus prevents gcc from making assumptions about
pointers passed to memory operations"
* emailed patches from Guenter Roeck <linux@roeck-us.net>:
alpha: Use absolute_pointer to define COMMAND_LINE
alpha: Move setup.h out of uapi
net: i825xx: Use absolute_pointer for memcpy from fixed memory location
compiler.h: Introduce absolute_pointer macro
net: i825xx: Use absolute_pointer for memcpy from fixed memory location
gcc 11.x reports the following compiler warning/error.
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Use absolute_pointer() to work around the problem.
absolute_pointer() disassociates a pointer from its originating symbol
type and context. Use it to prevent compiler warnings/errors such as
drivers/net/ethernet/i825xx/82596.c: In function 'i82596_probe':
arch/m68k/include/asm/string.h:72:25: error:
'__builtin_memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
Such warnings may be reported by gcc 11.x for string and memory
operations on fixed addresses.
tools/bootconfig: Define memblock_free_ptr() to fix build error
The lib/bootconfig.c file is shared with the 'bootconfig' tooling, and
as a result, the changes incommit 77e02cf57b6c ("memblock: introduce
saner 'memblock_free_ptr()' interface") need to also be reflected in the
tooling header file.
So define the new memblock_free_ptr() wrapper, and remove unused __pa()
and memblock_free().
Randy Dunlap [Mon, 13 Sep 2021 22:06:05 +0000 (15:06 -0700)]
ptp: dp83640: don't define PAGE0
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Richard Cochran <richard.cochran@omicron.at> Cc: John Stultz <john.stultz@linaro.org> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On sparc64, __fls() returns an "int", but the drm TTM code expected it
to be "unsigned long" as on x86. As a result, on sparc (and arc, and
m68k) you get build errors because 'min()' checks that the types match.
As suggested by Linus, it can use min_t instead of min to force the type
to be "unsigned int".
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexdeucher@gmail.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The boot-time allocation interface for memblock is a mess, with
'memblock_alloc()' returning a virtual pointer, but then you are
supposed to free it with 'memblock_free()' that takes a _physical_
address.
Not only is that all kinds of strange and illogical, but it actually
causes bugs, when people then use it like a normal allocation function,
and it fails spectacularly on a NULL pointer:
I really don't want to apply patches that treat the symptoms, when the
fundamental cause is this horribly confusing interface.
I started out looking at just automating a sane replacement sequence,
but because of this mix or virtual and physical addresses, and because
people have used the "__pa()" macro that can take either a regular
kernel pointer, or just the raw "unsigned long" address, it's all quite
messy.
So this just introduces a new saner interface for freeing a virtual
address that was allocated using 'memblock_alloc()', and that was kept
as a regular kernel pointer. And then it converts a couple of users
that are obvious and easy to test, including the 'xbc_nodes' case in
lib/bootconfig.c that caused problems.
Reported-by: kernel test robot <oliver.sang@intel.com> Fixes: 40caa127f3c7 ("init: bootconfig: Remove all bootconfig data when the init memory is removed") Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Mike Rapoport <rppt@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipc: remove memcg accounting for sops objects in do_semtimedop()
Linus proposes to revert an accounting for sops objects in
do_semtimedop() because it's really just a temporary buffer
for a single semtimedop() system call.
This object can consume up to 2 pages, syscall is sleeping
one, size and duration can be controlled by user, and this
allocation can be repeated by many thread at the same time.
However Shakeel Butt pointed that there are much more popular
objects with the same life time and similar memory
consumption, the accounting of which was decided to be
rejected for performance reasons.
Considering at least 2 pages for task_struct and 2 pages for
the kernel stack, a back of the envelope calculation gives a
footprint amplification of <1.5 so this temporal buffer can be
safely ignored.
The factor would IMO be interesting if it was >> 2 (from the
PoV of excessive (ab)use, fine-grained accounting seems to be
currently unfeasible due to performance impact).
Link: https://lore.kernel.org/lkml/90e254df-0dfe-f080-011e-b7c53ee7fd20@virtuozzo.com/ Fixes: 18319498fdd4 ("memcg: enable accounting of ipc resources") Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Michal Koutný <mkoutny@suse.com> Acked-by: Shakeel Butt <shakeelb@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michael Ellerman [Tue, 14 Sep 2021 12:17:23 +0000 (22:17 +1000)]
powerpc/boot: Fix build failure since GCC 4.9 removal
Stephen reported that the build was broken since commit 6d2ef226f2f1 ("compiler_attributes.h: drop __has_attribute() support for
gcc4"), with errors such as:
include/linux/compiler_attributes.h:296:5: warning: "__has_attribute" is not defined, evaluates to 0 [-Wundef]
296 | #if __has_attribute(__warning__)
| ^~~~~~~~~~~~~~~
make[2]: *** [arch/powerpc/boot/Makefile:225: arch/powerpc/boot/crt0.o] Error 1
But we expect __has_attribute() to always be defined now that we've
stopped using GCC 4.
Linus debugged it to the point of reading the GCC sources, and noticing
that the problem is that __has_attribute() is not defined when
preprocessing assembly files, which is what we're doing here.
Our assembly files don't include, or need, compiler_attributes.h, but
they are getting it unconditionally from the -include in BOOT_CFLAGS,
which is then added in its entirety to BOOT_AFLAGS.
That -include was added in commit 77433830ed16 ("powerpc: boot: include
compiler_attributes.h") so that we'd have "fallthrough" and other
attributes defined for the C files in arch/powerpc/boot. But it's not
needed for assembly files.
The minimal fix is to move the addition to BOOT_CFLAGS of -include
compiler_attributes.h until after we've copied BOOT_CFLAGS into
BOOT_AFLAGS. That avoids including compiler_attributes.h for asm files,
but makes no other change to BOOT_CFLAGS or BOOT_AFLAGS.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Debugged-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As mentioned in https://lkml.org/lkml/2021/9/13/1819
5 years old commit 919483096bfe ("ipv4: fix memory leaks in ip_cmsg_send() callers")
was a correct fix.
ip_cmsg_send() can loop over multiple cmsghdr()
If IP_RETOPTS has been successful, but following cmsghdr generates an error,
we do not free ipc.ok
If IP_RETOPTS is not successful, we have freed the allocated temporary space,
not the one currently in ipc.opt.
Sure, code could be refactored, but let's not bring back old bugs.
Fixes: d7807a9adf48 ("Revert "ipv4: fix memory leaks in ip_cmsg_send() callers"") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: fix tp->undo_retrans accounting in tcp_sacktag_one()
Commit 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit
time") may directly retrans a multiple segments TSO/GSO packet without
split, Since this commit, we can no longer assume that a retransmitted
packet is a single segment.
This patch fixes the tp->undo_retrans accounting in tcp_sacktag_one()
that use the actual segments(pcount) of the retransmitted packet.
Before that commit (10d3be569243), the assumption underlying the
tp->undo_retrans-- seems correct.
Fixes: 10d3be569243 ("tcp-tso: do not split TSO packets at retransmit time") Signed-off-by: zhenggy <zhenggy@chinatelecom.cn> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 13 day(s) which contain
a total of 18 files changed, 334 insertions(+), 193 deletions(-).
The main changes are:
1) Fix mmap_lock lockdep splat in BPF stack map's build_id lookup, from Yonghong Song.
2) Fix BPF cgroup v2 program bypass upon net_cls/prio activation, from Daniel Borkmann.
3) Fix kvcalloc() BTF line info splat on oversized allocation attempts, from Bixuan Cui.
4) Fix BPF selftest build of task_pt_regs test for arm64/s390, from Jean-Philippe Brucker.
5) Fix BPF's disasm.{c,h} to dual-license so that it is aligned with bpftool given the former
is a build dependency for the latter, from Daniel Borkmann with ACKs from contributors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: cc36a070b590 ("net-caif: add CAIF netdevice") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
which breaks S3-resume on fi-kbl-soraka presumably as that's slow enough
to trigger the alarm during the suspend.
Fixes: 6950d046eb6e ("rtc: cmos: Replace spin_lock_irqsave with spin_lock in hard IRQ")
References: 66e4f4a9cc38 ("rtc: cmos: Use spin_lock_irqsave() in cmos_interrupt()"): Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Xiaofei Tan <tanxiaofei@huawei.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20210305122140.28774-1-chris@chris-wilson.co.uk
Daniel Borkmann [Mon, 13 Sep 2021 23:07:59 +0000 (01:07 +0200)]
bpf, selftests: Add test case for mixed cgroup v1/v2
Minimal selftest which implements a small BPF policy program to the
connect(2) hook which rejects TCP connection requests to port 60123
with EPERM. This is being attached to a non-root cgroup v2 path. The
test asserts that this works under cgroup v2-only and under a mixed
cgroup v1/v2 environment where net_classid is set in the former case.
Minimal set of helpers for net_cls classid cgroupv1 management in order
to set an id, join from a process, initiate setup and teardown. cgroupv2
helpers are left as-is, but reused where possible.
Daniel Borkmann [Mon, 13 Sep 2021 23:07:57 +0000 (01:07 +0200)]
bpf, cgroups: Fix cgroup v2 fallback on v1/v2 mixed mode
Fix cgroup v1 interference when non-root cgroup v2 BPF programs are used.
Back in the days, commit bd1060a1d671 ("sock, cgroup: add sock->sk_cgroup")
embedded per-socket cgroup information into sock->sk_cgrp_data and in order
to save 8 bytes in struct sock made both mutually exclusive, that is, when
cgroup v1 socket tagging (e.g. net_cls/net_prio) is used, then cgroup v2
falls back to the root cgroup in sock_cgroup_ptr() (&cgrp_dfl_root.cgrp).
The assumption made was "there is no reason to mix the two and this is in line
with how legacy and v2 compatibility is handled" as stated in bd1060a1d671.
However, with Kubernetes more widely supporting cgroups v2 as well nowadays,
this assumption no longer holds, and the possibility of the v1/v2 mixed mode
with the v2 root fallback being hit becomes a real security issue.
Many of the cgroup v2 BPF programs are also used for policy enforcement, just
to pick _one_ example, that is, to programmatically deny socket related system
calls like connect(2) or bind(2). A v2 root fallback would implicitly cause
a policy bypass for the affected Pods.
In production environments, we have recently seen this case due to various
circumstances: i) a different 3rd party agent and/or ii) a container runtime
such as [0] in the user's environment configuring legacy cgroup v1 net_cls
tags, which triggered implicitly mentioned root fallback. Another case is
Kubernetes projects like kind [1] which create Kubernetes nodes in a container
and also add cgroup namespaces to the mix, meaning programs which are attached
to the cgroup v2 root of the cgroup namespace get attached to a non-root
cgroup v2 path from init namespace point of view. And the latter's root is
out of reach for agents on a kind Kubernetes node to configure. Meaning, any
entity on the node setting cgroup v1 net_cls tag will trigger the bypass
despite cgroup v2 BPF programs attached to the namespace root.
Generally, this mutual exclusiveness does not hold anymore in today's user
environments and makes cgroup v2 usage from BPF side fragile and unreliable.
This fix adds proper struct cgroup pointer for the cgroup v2 case to struct
sock_cgroup_data in order to address these issues; this implicitly also fixes
the tradeoffs being made back then with regards to races and refcount leaks
as stated in bd1060a1d671, and removes the fallback, so that cgroup v2 BPF
programs always operate as expected.
Bixuan Cui [Sat, 11 Sep 2021 00:55:57 +0000 (08:55 +0800)]
bpf: Add oversize check before call kvcalloc()
Commit 7661809d493b ("mm: don't allow oversized kvmalloc() calls") add the
oversize check. When the allocation is larger than what kmalloc() supports,
the following warning triggered:
This occurs after commit 4e59869aa655 ("compiler-gcc.h: drop checks for
older GCC versions"), which removed the GCC_VERSION gating. The removed
version check just so happened to prevent __compiletime_error() from
being defined with clang because it pretends to be GCC 4.2.1 for
compatibility but the error attribute was not added to clang until
14.0.0.
Commit 815f0ddb346c ("include/linux/compiler*.h: make compiler-*.h
mutually exclusive") and commit a3f8a30f3f00 ("Compiler Attributes: use
feature checks instead of version checks") refactored the handling of
attributes in the main kernel to avoid situations like this but that
refactoring has never been done for the tools directory.
Refactoring is a rather large undertaking and this has never been an
issue before so instead, just guard the definition of
__compiletime_error() with __has_attribute() so that there are no more
errors.
Fixes: 4e59869aa655 ("compiler-gcc.h: drop checks for older GCC versions") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'gcc-min-version-5.1' (make gcc-5.1 the minimum version)
Merge patch series from Nick Desaulniers to update the minimum gcc
version to 5.1.
This is some of the left-overs from the merge window that I didn't want
to deal with yesterday, so it comes in after -rc1 but was sent before.
Gcc-4.9 support has been an annoyance for some time, and with -Werror I
had the choice of applying a fairly big patch from Kees Cook to remove a
fair number of initializer warnings (still leaving some), or this patch
series from Nick that just removes the source of the problem.
The initializer cleanups might still be worth it regardless, but
honestly, I preferred just tackling the problem with gcc-4.9 head-on.
We've been more aggressiuve about no longer having to care about
compilers that were released a long time ago, and I think it's been a
good thing.
I added a couple of patches on top to sort out a few left-overs now that
we no longer support gcc-4.x.
As noted by Arnd, as a result of this minimum compiler version upgrade
we can probably change our use of '--std=gnu89' to '--std=gnu11', and
finally start using local loop declarations etc. But this series does
_not_ yet do that.
Link: https://lore.kernel.org/all/20210909182525.372ee687@canb.auug.org.au/ Link: https://lore.kernel.org/lkml/CAK7LNASs6dvU6D3jL2GG3jW58fXfaj6VNOe55NJnTB8UPuk2pA@mail.gmail.com/ Link: https://github.com/ClangBuiltLinux/linux/issues/1438
* emailed patches from Nick Desaulniers <ndesaulniers@google.com>:
Drop some straggling mentions of gcc-4.9 as being stale
compiler_attributes.h: drop __has_attribute() support for gcc4
vmlinux.lds.h: remove old check for GCC 4.9
compiler-gcc.h: drop checks for older GCC versions
Makefile: drop GCC < 5 -fno-var-tracking-assignments workaround
arm64: remove GCC version check for ARCH_SUPPORTS_INT128
powerpc: remove GCC version check for UPD_CONSTR
riscv: remove Kconfig check for GCC version for ARCH_RV64I
Kconfig.debug: drop GCC 5+ version check for DWARF5
mm/ksm: remove old GCC 4.9+ check
compiler.h: drop fallback overflow checkers
Documentation: raise minimum supported version of GCC to 5.1
compiler_attributes.h: drop __has_attribute() support for gcc4
Now that GCC 5.1 is the minimally supported default, the manual
workaround for older gcc versions not having __has_attribute() are no
longer relevant and can be removed.
Nick Desaulniers [Fri, 10 Sep 2021 23:40:47 +0000 (16:40 -0700)]
vmlinux.lds.h: remove old check for GCC 4.9
Now that GCC 5.1 is the minimally supported version of GCC, we can
effectively revert commit 85c2ce9104eb ("sched, vmlinux.lds: Increase
STRUCT_ALIGNMENT to 64 bytes for GCC-4.9")
Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Desaulniers [Fri, 10 Sep 2021 23:40:38 +0000 (16:40 -0700)]
Documentation: raise minimum supported version of GCC to 5.1
commit fad7cd3310db ("nbd: add the check to prevent overflow in
__nbd_ioctl()") raised an issue from the fallback helpers added in
commit f0907827a8a9 ("compiler.h: enable builtin overflow checkers and
add fallback code")
Specifically, the helpers for checking whether the results of a
multiplication overflowed (__unsigned_mul_overflow,
__signed_add_overflow) use the division operator when
!COMPILER_HAS_GENERIC_BUILTIN_OVERFLOW. This is problematic for 64b
operands on 32b hosts.
Also, because the macro is type agnostic, it is very difficult to write
a similarly type generic macro that dispatches to one of:
* div64_s64
* div64_u64
* div_s64
* div_u64
Raising the minimum supported versions allows us to remove all of the
fallback helpers for !COMPILER_HAS_GENERIC_BUILTIN_OVERFLOW, instead
dispatching the compiler builtins.
arm64 has already raised the minimum supported GCC version to 5.1, do
this for all targets now. See the link below for the previous
discussion.
Will Deacon [Mon, 13 Sep 2021 16:35:47 +0000 (17:35 +0100)]
x86/uaccess: Fix 32-bit __get_user_asm_u64() when CC_HAS_ASM_GOTO_OUTPUT=y
Commit 865c50e1d279 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT")
added an optimised version of __get_user_asm() for x86 using 'asm goto'.
Like the non-optimised code, the 32-bit implementation of 64-bit
get_user() expands to a pair of 32-bit accesses. Unlike the
non-optimised code, the _original_ pointer is incremented to copy the
high word instead of loading through a new pointer explicitly
constructed to point at a 32-bit type. Consequently, if the pointer
points at a 64-bit type then we end up loading the wrong data for the
upper 32-bits.
This was observed as a mount() failure in Android targeting i686 after b0cfcdd9b967 ("d_path: make 'prepend()' fill up the buffer exactly on
overflow") because the call to copy_from_kernel_nofault() from
prepend_copy() ends up in __get_kernel_nofault() and casts the source
pointer to a 'u64 __user *'. An attempt to mount at "/debug_ramdisk"
therefore ends up failing trying to mount "/debumdismdisk".
Use the existing '__gu_ptr' source pointer to unsigned int for 32-bit
__get_user_asm_u64() instead of the original pointer.
Cc: Bill Wendling <morbo@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Peter Zijlstra <peterz@infradead.org> Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: 865c50e1d279 ("x86/uaccess: utilize CONFIG_CC_HAS_ASM_GOTO_OUTPUT") Signed-off-by: Will Deacon <will@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net: hns3: fix the timing issue of VF clearing interrupt sources
Currently, the VF does not clear the interrupt source immediately after
receiving the interrupt. As a result, if the second interrupt task is
triggered when processing the first interrupt task, clearing the
interrupt source before exiting will clear the interrupt sources of the
two tasks at the same time. As a result, no interrupt is triggered for
the second task. The VF detects the missed message only when the next
interrupt is generated.
Clearing it immediately after executing check_evt_cause ensures that:
1. Even if two interrupt tasks are triggered at the same time, they can
be processed.
2. If the second task is triggered during the processing of the first
task and the interrupt source is not cleared, the interrupt is reported
after vector0 is enabled.
Fixes: b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When the command for querying imp info is issued to the firmware,
if the firmware does not support the command, the returned value
of bd num is 0.
Add protection mechanism before alloc memory to prevent apply for
0-length memory.
Fixes: 0b198b0d80ea ("net: hns3: refactor dump m7 info of debugfs") Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Mon, 13 Sep 2021 13:08:23 +0000 (21:08 +0800)]
net: hns3: disable mac in flr process
The firmware will not disable mac in flr process. Therefore, the driver
needs to proactively disable mac during flr, which is the same as the
function reset.
Fixes: 35d93a30040c ("net: hns3: adjust the process of PF reset") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Mon, 13 Sep 2021 13:08:22 +0000 (21:08 +0800)]
net: hns3: change affinity_mask to numa node range
Currently, affinity_mask is set to a single cpu. As a result,
irqbalance becomes invalid in SUBSET or EXACT mode. To solve
this problem, change affinity_mask to numa node range. In this
way, irqbalance can be performed on the cpu of the numa node.
Fixes: 0812545487ec ("net: hns3: add interrupt affinity support for misc interrupt") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Mon, 13 Sep 2021 13:08:21 +0000 (21:08 +0800)]
net: hns3: pad the short tunnel frame before sending to hardware
The hardware cannot handle short tunnel frames below 65 bytes,
and will cause vlan tag missing problem. So pads packet size to
65 bytes for tunnel frames to fix this bug.
Fixes: 3db084d28dc0("net: hns3: Fix for vxlan tx checksum bug") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 13 Sep 2021 13:08:20 +0000 (21:08 +0800)]
net: hns3: add option to turn off page pool feature
When page pool is added to the hns3 driver, it is always
enabled unconditionally, which means spilt page handling
in the hns3 driver is dead code.
As there is a requirement to test the performance between
spilt page handling in driver and page pool, so add a module
param to support disabling the page pool.
When the page pool is proved to perform better in most case,
the spilt page handling in driver can be removed.
Fixes: 93188e9642c3 ("net: hns3: support skb's frag page recycling based on page pool") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The delay is especially needed by the xRX300 and xRX330 SoCs. Without
this patch, some phys are sometimes not properly detected.
The patch was tested on BT Home Hub 5A and D-Link DWR-966.
Fixes: a09d042b0862 ("net: dsa: lantiq: allow to use all GPHYs on xRX300 and xRX330") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Hoang Le [Mon, 13 Sep 2021 09:28:52 +0000 (16:28 +0700)]
tipc: increase timeout in tipc_sk_enqueue()
In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.
To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).
Fixes: c637c1035534 ("tipc: resolve race problem at unicast message reception") Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Mon, 13 Sep 2021 07:53:49 +0000 (10:53 +0300)]
udp_tunnel: Fix udp_tunnel_nic work-queue type
Turn udp_tunnel_nic work-queue to an ordered work-queue. This queue
holds the UDP-tunnel configuration commands of the different netdevs.
When the netdevs are functions of the same NIC the order of
execution may be crucial.
Problem example:
NIC with 2 PFs, both PFs declare offload quota of up to 3 UDP-ports.
$ifconfig eth2 1.1.1.1/16 up
$ip link add eth2_19503 type vxlan id 5049 remote 1.1.1.2 dev eth2 dstport 19053
$ip link set dev eth2_19503 up
$ip link add eth2_19504 type vxlan id 5049 remote 1.1.1.3 dev eth2 dstport 19054
$ip link set dev eth2_19504 up
$ip link add eth2_19505 type vxlan id 5049 remote 1.1.1.4 dev eth2 dstport 19055
$ip link set dev eth2_19505 up
$ip link add eth2_19506 type vxlan id 5049 remote 1.1.1.5 dev eth2 dstport 19056
$ip link set dev eth2_19506 up
NIC RX port offload infrastructure offloads the first 3 UDP-ports (on
all devices which sets NETIF_F_RX_UDP_TUNNEL_PORT feature) and not
UDP-port 19056. So both PFs gets this offload configuration.
$ip link set dev eth2_19504 down
This triggers udp-tunnel-core to remove the UDP-port 19504 from
offload-ports-list and offload UDP-port 19056 instead.
In this scenario it is important that the UDP-port of 19504 will be
removed from both PFs before trying to add UDP-port 19056. The NIC can
stop offloading a UDP-port only when all references are removed.
Otherwise the NIC may report exceeding of the offload quota.
Fixes: cc4e3835eff4 ("udp_tunnel: add central NIC RX port offload infrastructure") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is only when ip_options_get() return zero need to free.
It already called kfree() when return error.
Fixes: 919483096bfe ("ipv4: fix memory leaks in ip_cmsg_send() callers") Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 13 Sep 2021 11:31:13 +0000 (12:31 +0100)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes.
The first patch fixes an error recovery regression just introduced
about a week ago. The other two patches fix issues related to
freeing rings in the bnxt_close() path under error conditions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 12 Sep 2021 16:34:49 +0000 (12:34 -0400)]
bnxt_en: Clean up completion ring page arrays completely
We recently changed the completion ring page arrays to be dynamically
allocated to better support the expanded range of ring depths. The
cleanup path for this was not quite complete. It might cause the
shutdown path to crash if we need to abort before the completion ring
arrays have been allocated and initialized.
Fix it by initializing the ring_mem->pg_arr to NULL after freeing the
completion ring page array. Add a check in bnxt_free_ring() to skip
referencing the rmem->pg_arr if it is NULL.
Fixes: 03c7448790b8 ("bnxt_en: Don't use static arrays for completion ring pages") Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: make bnxt_free_skbs() safe to call after bnxt_free_mem()
The call to bnxt_free_mem(..., false) in the bnxt_half_open_nic() error
path will deallocate ring descriptor memory via bnxt_free_?x_rings(),
but because irq_re_init is false, the ring info itself is not freed.
To simplify error paths, deallocation functions have generally been
written to be safe when called on unallocated memory. It should always
be safe to call dev_close(), which calls bnxt_free_skbs() a second time,
even in this semi- allocated ring state.
Calling bnxt_free_skbs() a second time with the rings already freed will
cause NULL pointer dereference. Fix it by checking the rings are valid
before proceeding in bnxt_free_tx_skbs() and
bnxt_free_one_rx_ring_skbs().
Fixes: 975bc99a4a39 ("bnxt_en: Refactor bnxt_free_rx_skbs().") Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 12 Sep 2021 16:34:47 +0000 (12:34 -0400)]
bnxt_en: Fix error recovery regression
The recent patch has introduced a regression by not reading the reset
count in the ERROR_RECOVERY async event handler. We may have just
gone through a reset and the reset count has just incremented. If
we don't update the reset count in the ERROR_RECOVERY event handler,
the health check timer will see that the reset count has changed and
will initiate an unintended reset.
Restore the unconditional update of the reset count in
bnxt_async_event_process() if error recovery watchdog is enabled.
Also, update the reset count at the end of the reset sequence to
make it even more robust.
Fixes: 1b2b91831983 ("bnxt_en: Fix possible unintended driver initiated error recovery") Reviewed-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
m68k: mvme: Remove overdue #warnings in RTC handling
The warnings were introduced when converting the MVME147 and MVME16x
RTC handling from gettod to hwclk. Replace the #warning by a comment,
and return an error to inform the upper layer that writing to the RTC is
not yet supported.
arch/m68k/include/asm/raw_io.h:20:19: error:
cast to pointer from integer of different size
arch/m68k/include/asm/raw_io.h:30:32: error:
cast to pointer from integer of different size [-Werror=int-to-p
On m68k, io functions are defined as macros. The problem is seen if the
macro parameter variable size differs from the size of a pointer. Cast
the parameter of all io macros to unsigned long before casting it to
a pointer to fix the problem.
Merge tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Add missing fields and remove some duplicate fields when printing a
perf_event_attr.
- Fix hybrid config terms list corruption.
- Update kernel header copies, some resulted in new kernel features
being automagically added to 'perf trace' syscall/tracepoint argument
id->string translators.
- Add a file generated during the documentation build to .gitignore.
- Add an option to build without libbfd, as some distros, like Debian
consider its ABI unstable.
- Add support to print a textual representation of IBS raw sample data
in 'perf report'.
- Fix bpf 'perf test' sample mismatch reporting
- Fix passing arguments to stackcollapse report in a 'perf script'
python script.
- Allow build-id with trailing zeros.
- Look for ImageBase in PE file to compute .text offset.
* tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (25 commits)
tools headers UAPI: Update tools's copy of drm.h headers
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
tools headers UAPI: Sync linux/fs.h with the kernel sources
tools headers UAPI: Sync linux/in.h copy with the kernel sources
perf tools: Add an option to build without libbfd
perf tools: Allow build-id with trailing zeros
perf tools: Fix hybrid config terms list corruption
perf tools: Factor out copy_config_terms() and free_config_terms()
perf tools: Fix perf_event_attr__fprintf() missing/dupl. fields
perf tools: Ignore Documentation dependency file
perf bpf: Provide a weak btf__load_from_kernel_by_id() for older libbpf versions
tools include UAPI: Update linux/mount.h copy
perf beauty: Cover more flags in the move_mount syscall argument beautifier
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools include UAPI: Sync sound/asound.h copy with the kernel sources
tools headers UAPI: Sync linux/kvm.h with the kernel sources
tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
perf report: Add support to print a textual representation of IBS raw sample data
perf report: Add tools/arch/x86/include/asm/amd-ibs.h
perf env: Add perf_env__cpuid, perf_env__{nr_}pmu_mappings
...
* tag 'compiler-attributes-for-linus-v5.15-rc1-v2' of git://github.com/ojeda/linux:
compiler_attributes.h: move __compiletime_{error|warning}
MAINTAINERS: add Nick as Reviewer for compiler_attributes.h
Compiler Attributes: fix __has_attribute(__no_sanitize_coverage__) for GCC 4
Merge tag 'auxdisplay-for-linus-v5.15-rc1' of git://github.com/ojeda/linux
Pull auxdisplay updates from Miguel Ojeda:
"An assortment of improvements for auxdisplay:
- Replace symbolic permissions with octal permissions (Jinchao Wang)
- ks0108: Switch to use module_parport_driver() (Andy Shevchenko)
- charlcd: Drop unneeded initializers and switch to C99 style (Andy
Shevchenko)
- hd44780: Fix oops on module unloading (Lars Poeschel)
- Add I2C gpio expander example (Ralf Schlatterbeck)"
* tag 'auxdisplay-for-linus-v5.15-rc1' of git://github.com/ojeda/linux:
auxdisplay: Replace symbolic permissions with octal permissions
auxdisplay: ks0108: Switch to use module_parport_driver()
auxdisplay: charlcd: Drop unneeded initializers and switch to C99 style
auxdisplay: hd44780: Fix oops on module unloading
auxdisplay: Add I2C gpio expander example
Merge tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull CPU hotplug updates from Thomas Gleixner:
"Updates for the SMP and CPU hotplug:
- Remove DEFINE_SMP_CALL_CACHE_FUNCTION() which is a left over of the
original hotplug code and now causing trouble with the ARM64 cache
topology setup due to the pointless SMP function call.
It's not longer required as the hotplug callbacks are guaranteed to
be invoked on the upcoming CPU.
- Remove the deprecated and now unused CPU hotplug functions
- Rewrite the CPU hotplug API documentation"
* tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: core-api/cpuhotplug: Rewrite the API section
cpu/hotplug: Remove deprecated CPU-hotplug functions.
thermal: Replace deprecated CPU-hotplug functions.
drivers: base: cacheinfo: Get rid of DEFINE_SMP_CALL_CACHE_FUNCTION()
Merge tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc driver fix from Greg KH:
"Here is a single patch for 5.15-rc1, for the lkdtm misc driver.
It resolves a build issue that many people were hitting with your
current tree, and Kees and others felt would be good to get merged
before -rc1 comes out, to prevent them from having to constantly hit
it as many development trees restart on -rc1, not older -rc releases.
It has NOT been in linux-next, but has passed 0-day testing and looks
'obviously correct' when reviewing it locally :)"
* tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
lkdtm: Use init_uts_ns.name instead of macros
Merge tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Make sure the idle timer expires in hardirq context, on PREEMPT_RT
- Make sure the run-queue balance callback is invoked only on the
outgoing CPU
* tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Prevent balance_push() on remote runqueues
sched/idle: Make the idle timer expire in hard interrupt context
Merge tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Borislav Petkov:
- Fix the futex PI requeue machinery to not return to userspace in
inconsistent state
- Avoid a potential null pointer dereference in the ww_mutex deadlock
check
- Other smaller cleanups and optimizations
* tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rtmutex: Fix ww_mutex deadlock check
futex: Remove unused variable 'vpid' in futex_proxy_trylock_atomic()
futex: Avoid redundant task lookup
futex: Clarify comment for requeue_pi_wake_futex()
futex: Prevent inconsistent state and exit race
futex: Return error code instead of assigning it without effect
locking/rwsem: Add missing __init_rwsem() for PREEMPT_RT
Merge tag 'timers_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Borislav Petkov:
- Handle negative second values properly when converting a timespec64
to nanoseconds.
* tag 'timers_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Handle negative seconds correctly in timespec64_to_ns()
Merge branch 'misc.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull namei updates from Al Viro:
"Clearing fallout from mkdirat in io_uring series. The fix in the
kern_path_locked() patch plus associated cleanups"
* 'misc.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
putname(): IS_ERR_OR_NULL() is wrong here
namei: Standardize callers of filename_create()
namei: Standardize callers of filename_lookup()
rename __filename_parentat() to filename_parentat()
namei: Fix use after free in kern_path_locked
Merge tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull smbfs updates from Steve French:
"cifs/smb3 updates:
- DFS reconnect fix
- begin creating common headers for server and client
- rename the cifs_common directory to smbfs_common to be more
consistent ie change use of the name cifs to smb (smb3 or smbfs is
more accurate, as the very old cifs dialect has long been
superseded by smb3 dialects).
In the future we can rename the fs/cifs directory to fs/smbfs.
This does not include the set of multichannel fixes nor the two
deferred close fixes (they are still being reviewed and tested)"
* tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: properly invalidate cached root handle when closing it
cifs: move SMB FSCTL definitions to common code
cifs: rename cifs_common to smbfs_common
cifs: update FSCTL definitions
Len Baker [Sat, 11 Sep 2021 10:28:18 +0000 (12:28 +0200)]
net: mana: Prefer struct_size over open coded arithmetic
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.
Andrea Claudi [Sat, 11 Sep 2021 14:14:18 +0000 (16:14 +0200)]
selftest: net: fix typo in altname test
If altname deletion of the short alternative name fails, the error
message printed is: "Failed to add short alternative name".
This is obviously a typo, as we are testing altname deletion.
Fix this using a proper error message.
Fixes: f95e6c9c4617 ("selftest: net: add alternative names test") Signed-off-by: Andrea Claudi <aclaudi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ansuel Smith [Sat, 11 Sep 2021 15:50:09 +0000 (17:50 +0200)]
net: dsa: qca8k: fix kernel panic with legacy mdio mapping
When the mdio legacy mapping is used the mii_bus priv registered by DSA
refer to the dsa switch struct instead of the qca8k_priv struct and
causes a kernel panic. Create dedicated function when the internal
dedicated mdio driver is used to properly handle the 2 different
implementation.
Fixes: 759bafb8a322 ("net: dsa: qca8k: add support for internal phy and internal mdio") Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
- virtio-vsock support for end of record with SEQPACKET
- vdpa: mac and mq support for ifcvf and mlx5
- vdpa: management netlink for ifcvf
- virtio-i2c, gpio dt bindings
- misc fixes and cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
Documentation: Add documentation for VDUSE
vduse: Introduce VDUSE - vDPA Device in Userspace
vduse: Implement an MMU-based software IOTLB
vdpa: Support transferring virtual addressing during DMA mapping
vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
vhost-iotlb: Add an opaque pointer for vhost IOTLB
vhost-vdpa: Handle the failure of vdpa_reset()
vdpa: Add reset callback in vdpa_config_ops
vdpa: Fix some coding style issues
file: Export receive_fd() to modules
eventfd: Export eventfd_wake_count to modules
iova: Export alloc_iova_fast() and free_iova_fast()
virtio-blk: remove unneeded "likely" statements
virtio-balloon: Use virtio_find_vqs() helper
vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
vsock_test: update message bounds test for MSG_EOR
af_vsock: rename variables in receive loop
virtio/vsock: support MSG_EOR bit processing
vhost/vsock: support MSG_EOR bit processing
...
Merge branch 'for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux
Pull coccinelle updates from Julia Lawall:
"These changes update some existing semantic patches with
respect to some recent changes in the kernel.
Specifically, the change to kvmalloc.cocci searches for
kfree_sensitive rather than kzfree, and the change to
use_after_iter.cocci adds list_entry_is_head as a valid
use of a list iterator index variable after the end of
the loop"
* 'for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccinelle: allow list_entry_is_head() to use pos
coccinelle: api: rename kzfree to kfree_sensitive
$ tools/perf/trace/beauty/drm_ioctl.sh > before
$ cp include/uapi/drm/drm.h tools/include/uapi/drm/drm.h
$ tools/perf/trace/beauty/drm_ioctl.sh > after
$ diff -u before after
Silencing these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/drm/drm.h' differs from latest version at 'include/uapi/drm/drm.h'
diff -u tools/include/uapi/drm/drm.h include/uapi/drm/drm.h
Cc: Simon Ser <contact@emersion.fr> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
To pick the changes in:
b65a9489730a2494 ("drm/i915/userptr: Probe existence of backing struct pages upon creation") ee242ca704d38699 ("drm/i915/guc: Implement GuC priority management") 81340cf3bddded4f ("drm/i915/uapi: reject set_domain for discrete") 7961c5b60f23dff5 ("drm/i915: Add TTM offset argument to mmap.") aef7b67a79564f6c ("drm/i915/uapi: convert drm_i915_gem_userptr to kernel doc") e7737b67ab46ee0e ("drm/i915/uapi: reject caching ioctls for discrete") 3aa8c57fe25a9247 ("drm/i915/uapi: convert drm_i915_gem_set_domain to kernel doc") 289f5a72009b8f67 ("drm/i915/uapi: convert drm_i915_gem_caching to kernel doc") 4a766ae40ec83301 ("drm/i915: Drop the CONTEXT_CLONE API (v2)") 6ff6d61dd2a943bd ("drm/i915: Drop I915_CONTEXT_PARAM_NO_ZEROMAP") fe4751c3d513ff4f ("drm/i915: Drop I915_CONTEXT_PARAM_RINGSIZE") 577729533cdc4e37 ("drm/i915: Document the Virtual Engine uAPI") c649432e86ca677d ("drm/i915: Fix busy ioctl commentary")
That doesn't result in any changes to tooling as no new ioctl were
added (at least not perceived by tools/perf/trace/beauty/drm_ioctl.sh).
Addressing this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'
diff -u tools/include/uapi/drm/i915_drm.h include/uapi/drm/i915_drm.h
Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Matthew Auld <matthew.auld@intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools headers UAPI: Sync linux/fs.h with the kernel sources
To pick the change in:
7957d93bf32bc211 ("block: add ioctl to read the disk sequence number")
It adds a new ioctl, but we are still not using that to generate tables
for 'perf trace', so no changes in tooling.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/fs.h' differs from latest version at 'include/uapi/linux/fs.h'
diff -u tools/include/uapi/linux/fs.h include/uapi/linux/fs.h
tools headers UAPI: Sync linux/in.h copy with the kernel sources
To pick the changes in:
db243b796439c0ca ("net/ipv4/ipv6: Replace one-element arraya with flexible-array members") 2d3e5caf96b9449a ("net/ipv4: Replace one-element array with flexible-array member")
That don't result in any change in tooling, the structs changed remains
with the same layout.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net> Cc: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ian Rogers <irogers@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: tony garnock-jones <tonyg@leastfixedpoint.com> Link: http://lore.kernel.org/lkml/20210910225756.729087-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Namhyung Kim [Fri, 10 Sep 2021 22:46:30 +0000 (15:46 -0700)]
perf tools: Allow build-id with trailing zeros
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 39be8d0115b321ed ("perf tools: Pass build_id object to dso__build_id_equal()") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter [Thu, 9 Sep 2021 12:55:08 +0000 (15:55 +0300)]
perf tools: Fix hybrid config terms list corruption
A config terms list was spliced twice, resulting in a never-ending loop
when the list was traversed. Fix by using list_splice_init() and copying
and freeing the lists as necessary.
This patch also depends on patch "perf tools: Factor out
copy_config_terms() and free_config_terms()"
Example on ADL:
Before:
# perf record -e '{intel_pt//,cycles/aux-sample-size=4096/pp}' uname &
# jobs
[1]+ Running perf record -e "{intel_pt//,cycles/aux-sample-size=4096/pp}" uname
# perf top -E 10
PerfTop: 4071 irqs/sec kernel: 6.9% exact: 100.0% lost: 0/0 drop: 0/0 [4000Hz cycles], (all, 24 CPUs)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
projects / kernel.git / log