Kai Vehmanen [Thu, 3 Oct 2019 08:55:30 +0000 (11:55 +0300)]
drm/i915: Fix audio power up sequence for gen10+ display
On platfroms with gen10+ display, driver must set the enable bit of
AUDIO_PIN_BUF_CTL register before transactions with the HDA controller
can proceed. Add setting this bit to the audio power up sequence.
Failing to do this resulted in errors during display audio codec probe,
and failures during resume from suspend.
Note: We may also need to disable the bit afterwards, but there are
still unresolved issues with that.
Jani Nikula [Wed, 2 Oct 2019 14:41:38 +0000 (17:41 +0300)]
drm/i915/dp: remove static variable for aux last status
Add aux_busy_last_status to intel_dp. Don't bother with initializing to
all ones; the only difference is potentially missing logging for one
error case if the readout is all zeros.
Chris Wilson [Thu, 3 Oct 2019 21:00:56 +0000 (22:00 +0100)]
drm/i915/execlists: Skip redundant resubmission
If we unwind the active requests, and on resubmission discover that we
intend to preempt the active contexts with themselves, simply skip the
ELSP submission.
Imre Deak [Wed, 2 Oct 2019 20:41:08 +0000 (23:41 +0300)]
drm/i915/tgl: Add the Thunderbolt PLL divider values
The Thunderbolt PLL divider values on TGL differ from the ICL ones,
update the PLL parameter calculation function accordingly.
Bspec: 49204
v2:
- Remove unused refclk config. (José)
Cc: Jose Souza <jose.souza@intel.com> Cc: Clinton A Taylor <clinton.a.taylor@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Mika Westerberg <mika.westerberg@intel.com> Tested-by: Mika Westerberg <mika.westerberg@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: Jose Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191002204108.32242-1-imre.deak@intel.com
If execlists's lite-restore is based on the common GEM context tag
rather than the per-intel_context LRCA, then a context switch between
two intel_contexts on the same engine derived from the same GEM context
will perform a lite-restore instead of a full context switch. We can
exploit this by poisoning the ringbuffer of the first context and trying
to trick a simple RING_TAIL update (i.e. lite-restore)
v2: Also check what happens if preempt ce[0] with ce[1] (both instances
on the same engine from the same parent context) [Tvrtko]
drm/i915/mg: Use tc_port instead of port parameter to MG registers
All the MG registers is based on the tc_port not port, so
MG_PHY_PORT_LN() was subtracting port and PORT_C what is very
fragile.
So replacing port to tc_port in all MG register macros and users
like we have for DKL.
Chris Wilson [Wed, 2 Oct 2019 12:24:30 +0000 (13:24 +0100)]
drm/i915/selftests: Extract random_offset() for use with a prng
For selftests, we desire repeatability and so prefer using a prng with
known seed over true randomness. Extract random_offset() as a selftest
utility that can take the prng state.
Ville Syrjälä [Mon, 30 Sep 2019 18:30:45 +0000 (21:30 +0300)]
drm/i915: Fix g4x sprite scaling stride check with GTT remapping
I forgot to update the g4x sprite scaling stride check when GTT
remapping was introduced. The stride of the original framebuffer
is irrelevant when remapping is used and instead we want to check
the stride of the remapped view.
Also drop the duplicate width_bytes check. We already check that
a few lines earlier.
Ville Syrjälä [Tue, 1 Oct 2019 15:46:29 +0000 (18:46 +0300)]
drm/i915: Polish intel_tv_mode_valid()
Drop the tv_mode NULL check since intel_tv_mode_find() never
actually returns NULL, and flip the condition around so that
the MODE_OK case is at the end, which is customary to all
the other .mode_valid() implementations.
Ville Syrjälä [Tue, 1 Oct 2019 15:46:28 +0000 (18:46 +0300)]
drm/i915: Limit MST modes based on plane size too
When adding the max plane size checks to the .mode_valid() hooks
I naturally forgot about MST. Take care of that one as well.
Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Sean Paul <sean@poorly.run> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: 2d20411e25a3 ("drm/i915: Don't advertise modes that exceed the max plane size") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191001154629.11063-1-ville.syrjala@linux.intel.com Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Chris Wilson [Sat, 28 Sep 2019 08:25:46 +0000 (09:25 +0100)]
drm/i915/userptr: Never allow userptr into the mappable GGTT
Daniel Vetter uncovered a nasty cycle in using the mmu-notifiers to
invalidate userptr objects which also happen to be pulled into GGTT
mmaps. That is when we unbind the userptr object (on mmu invalidation),
we revoke all CPU mmaps, which may then recurse into mmu invalidation.
We looked for ways of breaking the cycle, but the revocation on
invalidation is required and cannot be avoided. The only solution we
could see was to not allow such GGTT bindings of userptr objects in the
first place. In practice, no one really wants to use a GGTT mmapping of
a CPU pointer...
Just before Daniel's explosive lockdep patches land in v5.4-rc1, we got
a genuine blip from CI:
<4>[ 246.793958] ======================================================
<4>[ 246.793972] WARNING: possible circular locking dependency detected
<4>[ 246.793989] 5.3.0-gbd6c56f50d15-drmtip_372+ #1 Tainted: G U
<4>[ 246.794003] ------------------------------------------------------
<4>[ 246.794017] kswapd0/145 is trying to acquire lock:
<4>[ 246.794030] 000000003f565be6 (&dev->struct_mutex/1){+.+.}, at: userptr_mn_invalidate_range_start+0x18f/0x220 [i915]
<4>[ 246.794250]
but task is already holding lock:
<4>[ 246.794263] 000000001799cef9 (&anon_vma->rwsem){++++}, at: page_lock_anon_vma_read+0xe6/0x2a0
<4>[ 246.794291]
which lock already depends on the new lock.
Srinivasan S [Wed, 25 Sep 2019 00:35:42 +0000 (06:05 +0530)]
drm/i915/dp: Fix DP MST error after unplugging TypeC cable
This patch avoids DP MST payload error message in dmesg, as it is trying
to update the payload to the disconnected DP MST device. After DP MST
device is disconnected we should not be updating the payload and
hence remove the error.
v2: Removed the connector status check and converted from error to debug.
Chris Wilson [Tue, 1 Oct 2019 10:35:18 +0000 (11:35 +0100)]
drm/i915: Initialise breadcrumb lists on the virtual engine
With deferring the breadcrumb signalling to the virtual engine (thanks
preempt-to-busy) we need to make sure the lists and irq-worker are ready
to send a signal.
Fixes: cb2377a919bb ("drm/i915: Fixup preempt-to-busy vs reset of a virtual request") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191001103518.9113-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 27 Sep 2019 16:03:35 +0000 (17:03 +0100)]
drm/i915/gt: Only unwedge if we can reset first
Unwedging the GPU requires a successful GPU reset before we restore the
default submission, or else we may see residual context switch events
that we were not expecting.
v2: Pull in the special-case reset_clobbers_display, and explain why it
should be safe in the context of unwedging.
v3: Just forget all about resets before unwedging if it will clobber the
display; risk it all.
Reported-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> #v1 Link: https://patchwork.freedesktop.org/patch/msgid/20190927160335.10622-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 30 Sep 2019 14:49:19 +0000 (15:49 +0100)]
drm/i915/selftests: Exercise context switching in parallel
We currently test context switching on each engine as a basic stress
test (just verifying that nothing explodes if we execute 2 requests from
different contexts sequentially). What we have not tested is what
happens if we try and do so on all available engines simultaneously,
putting our SW and the HW under the maximal stress.
v2: Clone the set of engines from the first context into the secondary
contexts.
Chris Wilson [Fri, 27 Sep 2019 21:17:48 +0000 (22:17 +0100)]
drm/i915/selftests: Distinguish mock device from no wakeref
On systems that have no runtime-pm, we mark the wakeref as being -1. We
therefore cannot use that value for the mock-gt indicator, so opt for
-ENODEV instead. The wakeref should never be an error value -- one
hopes!
Chris Wilson [Fri, 27 Sep 2019 21:17:47 +0000 (22:17 +0100)]
drm/i915: Pass intel_gt to has-reset?
As we execute GPU resets on a gt/ basis, and use the intel_gt as the
primary for all other reset functions, also use it for the has-reset?
predicates. Gradually simplifying the churn of pointers.
Link training is failling when running link at 2.7GHz and 1.62GHz and
following BSpec pll algorithm.
Comparing the values calculated and the ones from the reference table
it looks like MG_CLKTOP2_CORECLKCTL1_A_DIVRATIO should not always set
to 5. For DP ports ICL mg pll algorithm sets it to 10 or 5 based on
div2 value, that matches with dkl hardcoded table.
So implementing this way as it proved to work in HW and leaving a
comment so we know why it do not match BSpec.
v4:
Using the same is_dp check as ICL, need testing on HDMI over tc port
Clinton A Taylor [Thu, 26 Sep 2019 21:06:57 +0000 (14:06 -0700)]
drm/i915/tgl: Add dkl phy programming sequences
Added DKL Phy sequences and helpers functions to program voltage
swing, clock gating and dp mode.
It is not written in DP enabling sequence but "PHY Clockgating
programming" states that clock gating should be enabled after the
link training but doing so causes all the following trainings to fail
so not enabling it for.
v2:
Setting the right HIP_INDEX_REG bits (José)
v3:
Adding the meaning of each column of tgl_dkl_phy_ddi_translations
Adding if gen >= 12 on intel_ddi_hdmi_level() and
intel_ddi_pre_enable_hdmi() instead of reuse part of gen >= 11 if
v4:
Moved the DP_MODE lane programing to another patch as ICL also
needed it
Sharing icl_phy_set_clock_gating() and icl_program_mg_dp_mode() with
TGL as bits and programing as now it almost identical to ICL
Clinton A Taylor [Thu, 26 Sep 2019 21:06:56 +0000 (14:06 -0700)]
drm/i915/tc: Update DP_MODE programming
BSpec was updated(r146548) with a new MG_DP_MODE Programming table,
now taking in consideration the pin assignment and allowing us to
optimize power by shutting down available but not needed lanes.
It was tested on ICL and TGL, with adaptors that used pin assignment
C and B, reversing the connector and going to different modes testing
the not needed lane shutdown.
v5:
Using crtc_state->lane_count instead of dp.lane_count
The HuC FW has silently switched to encoding the version the same way as
the GuC FW does, i.e. major.minor.patch instead of just major.minor. All
the current blobs follow the new scheme, but since minor and patch are
both zero there is no difference in the end results and we happily load
them. New binaries, however, will have non-zero values in there, so we
need to make sure to parse them correctly.
Michał Winiarski [Thu, 26 Sep 2019 10:06:33 +0000 (12:06 +0200)]
drm/i915: Add definitions for MI_MATH command
We can use it in i915 for updating parts of unmasked registers from
within a batch. We're also adding Gen8+ versions of CS_GPR registers
(aka MI_MATH_REG in the coprocessor).
Anna Karas [Thu, 26 Sep 2019 12:21:58 +0000 (15:21 +0300)]
drm/i915/perf: Fix use of kernel-doc format in structure members
Insert structure members names into their descriptions to follow
kernel-doc format.
Cc: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Anna Karas <anna.karas@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190926122158.13028-1-anna.karas@intel.com
drm/i915: Don't disable interrupts for intel_engine_breadcrumbs_irq()
The function intel_engine_breadcrumbs_irq() is always invoked from an interrupt
handler and for that reason it invokes (as an optimisation) only spin_lock()
for locking assuming that the interrupts are already disabled. The
function intel_engine_signal_breadcrumbs() is provided to disable
interrupts while the former function is invoked so that assumption is
also true for callers from preemptible context.
On PREEMPT_RT local_irq_disable() really disables interrupts and this
forbids to invoke spin_lock() which becomes a sleeping spinlock.
This is also problematic with `threadirqs' in conjunction with
irq_work. With force threading the interrupt handler, the handler is
invoked with disabled BH but with interrupts enabled. This is okay and
the lock itself is never acquired in IRQ context. This changes with
irq_work (signal_irq_work()) which _still_ invokes
intel_engine_breadcrumbs_irq() from IRQ context. Lockdep should see this
and complain.
Acquire the locks in intel_engine_breadcrumbs_irq() with _irqsave()
suffix and let all callers invoke intel_engine_breadcrumbs_irq()
directly instead using intel_engine_signal_breadcrumbs().
The lockdep_assert_irqs_disabled() check is needless. The previous
lockdep_assert_held() check ensures that the lock is acquired and while
the lock is acquired lockdep also prints a warning if the interrupts are
not disabled if they have to be.
These IRQ-off asserts trigger on PREEMPT_RT because the locks become
sleeping locks and do not really disable interrupts.
Michał Winiarski [Thu, 26 Sep 2019 13:31:41 +0000 (14:31 +0100)]
drm/i915/execlists: Use per-process HWSP as scratch
Some of our commands (MI_FLUSH_DW / PIPE_CONTROL) require a post-sync write
operation to be performed. Currently we're using dedicated VMA for
PIPE_CONTROL and global HWSP for MI_FLUSH_DW.
On execlists platforms, each of our contexts has an area that can be
used as scratch space. Let's use that instead.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190926133142.2838-2-chris@chris-wilson.co.uk
Michał Winiarski [Thu, 26 Sep 2019 13:31:40 +0000 (14:31 +0100)]
drm/i915: Define explicit wedged on init reset state
We're currently using scratch presence as a way of identifying that we
entered wedged state at driver initialization time.
Let's use a separate flag rather than rely on scratch.
Matt Roper [Wed, 25 Sep 2019 23:45:42 +0000 (16:45 -0700)]
drm/i915: Small joiner RAM buffer size is platform-specific
According to the bspec, GLK/CNL have a smaller small joiner RAM buffer
than ICL+. This feels like something that could easily change again on
future platforms, so let's just add a function to return the proper
per-platform buffer size. That may also slightly simplify the upcoming
bigjoiner enabling.
Since we have to change intel_dp_dsc_get_output_bpp()'s signature to
pass the dev_priv down for the platform check, let's take the
opportunity to also make that function static since it isn't used
outside the intel_dp file.
James Ausmus [Tue, 24 Sep 2019 22:28:29 +0000 (15:28 -0700)]
drm/i915/tgl: Add memory type decoding for bandwidth checking
The memory type values have changed in TGL, so we need to translate them
differently than ICL. While we're moving it, fix up the ICL translation
for LPDDR4.
BSpec: 53998
v2: Fix up ICL LPDDR4 entry (Ville); Drop unused values from TGL (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Signed-off-by: James Ausmus <james.ausmus@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Stuart Summers <stuart.summers@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190924222829.13142-1-james.ausmus@intel.com
Lucas De Marchi [Tue, 24 Sep 2019 21:00:38 +0000 (14:00 -0700)]
drm/i915/tgl: re-indent code to prepare for DKL changes
The final save operation into pll_state of the calculations done will
be different for DKL PHY. Prepare for that by reindenting code so it's
easier to check for correctness. This one has no change in behavior.
Lucas De Marchi [Tue, 24 Sep 2019 21:00:35 +0000 (14:00 -0700)]
drm/i915/tgl: Add initial dkl pll support
The disable function can be the same as for MG phy since the same
registers are used. The others are different as registers changed,
also adding a empty dkl_pll_write() to be implemented later.
v2:
Setting the right HIP_INDEX_REG bits (José)
v3:
Masking non-computed registers of mg_pll_tdc_coldst_bias
when getting hardware state
Sharing mg_pll_enable() with TGL
Chris Wilson [Wed, 25 Sep 2019 13:08:45 +0000 (14:08 +0100)]
drm/i915/execlists: Simplify gen12_csb_parse
Having decided that we only care about the promotion predicate, we can
simplify gen12_csb_parse to simply check whether we need to jump to a
new queue.
Rename linked_plane to planar_linked_plane and slave to planar_slave,
this will make it easier to keep apart bigjoiner linking and planar plane
linking.
We had this as an optimization to not do a plane update, but we killed
it off because there are so many reasons we may have to do a plane
update or fastset that it's best to just assume everything changed.
Readout the FEC state in encoder->get_config(), this will allow
us to ensure that we can correctly inherit the state from boot,
and that we set FEC during modeset.
There was a integer wraparound when mode_clock became too high,
and we didn't correct for the FEC overhead factor when dividing,
with the calculations breaking at HBR3.
As a result our calculated bpp was way too high, and the link width
limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just
in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%,
all the calculations use 1/0.972261, and the same ratio should be
applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogus fec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: d9218c8f6cf4 ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC") Cc: <stable@vger.kernel.org> # v5.0+ Cc: Manasi Navare <manasi.d.navare@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190925082110.17439-1-maarten.lankhorst@linux.intel.com Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Chris Wilson [Tue, 24 Sep 2019 17:35:01 +0000 (18:35 +0100)]
drm/i915/tgl: Swap engines for no rps (gpu reclocking)
If we disable rps, it appears the Tigerlake is stable enough to run
multiple engines simultaneously in CI. As disabling rps should only
cause the execution to be slow, whereas many features depend on the
different engines, we would prefer to have the engines enabled while the
machine hangs are being debugged.
drm/i915: Add Pipe D cursor ctrl register for Gen12
Currently the offset for PIPE D cursor control register is missing in
i915_reg.h due to which the cursor plane cannot be enabled for Pipe D.
This also causes kernel Warning, when a user requests to enable cursor
plane for PIPE D for Gen 12 platforms.
This patch adds the CURSOR_CTL_D register in the i915_reg.h.
Chris Wilson [Tue, 24 Sep 2019 14:59:50 +0000 (15:59 +0100)]
drm/i915/selftests: Verify the LRC register layout between init and HW
Before we submit the first context to HW, we need to construct a valid
image of the register state. This layout is defined by the HW and should
match the layout generated by HW when it saves the context image.
Asserting that this should be equivalent should help avoid any undefined
behaviour and verify that we haven't missed anything important!
Of course, having insisted that the initial register state within the
LRC should match that returned by HW, we need to ensure that it does.
v2: Drop the RELATIVE_MMIO flag from gen11, we ignore it for
constructing the lrc image.
Added bandwidth calculation algorithm and checks,
similar way as it was done for ICL, some constants
were corrected according to BSpec 53998.
v2: Start using same icl_get_bw_info function to avoid
code duplication. Moved mpagesize to memory info
related structure as it is now dependent on memory type.
Fixed qi.t_bl field assignment.
v3: Removed mpagesize as unused. Duplicate code and redundant blankline
fixed.
v4: Changed ordering of IS_GEN checks as agreed. Minor commit
message fixes.
Chris Wilson [Fri, 20 Sep 2019 12:18:21 +0000 (13:18 +0100)]
drm/i915: Mark contents as dirty on a write fault
Since dropping the set-to-gtt-domain in commit a679f58d0510 ("drm/i915:
Flush pages on acquisition"), we no longer mark the contents as dirty on
a write fault. This has the issue of us then not marking the pages as
dirty on releasing the buffer, which means the contents are not written
out to the swap device (should we ever pick that buffer as a victim).
Notably, this is visible in the dumb buffer interface used for cursors.
Having updated the cursor contents via mmap, and swapped away, if the
shrinker should evict the old cursor, upon next reuse, the cursor would
be invisible.
E.g. echo 80 > /proc/sys/kernel/sysrq ; echo f > /proc/sysrq-trigger
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111541 Fixes: a679f58d0510 ("drm/i915: Flush pages on acquisition") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.william.auld@gmail.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: <stable@vger.kernel.org> # v5.2+ Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190920121821.7223-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 23 Sep 2019 15:28:44 +0000 (16:28 +0100)]
drm/i915: Prevent bonded requests from overtaking each other on preemption
Force bonded requests to run on distinct engines so that they cannot be
shuffled onto the same engine where timeslicing will reverse the order.
A bonded request will often wait on a semaphore signaled by its master,
creating an implicit dependency -- if we ignore that implicit dependency
and allow the bonded request to run on the same engine and before its
master, we will cause a GPU hang. [Whether it will hang the GPU is
debatable, we should keep on timeslicing and each timeslice should be
"accidentally" counted as forward progress, in which case it should run
but at one-half to one-third speed.]
We can prevent this inversion by restricting which engines we allow
ourselves to jump to upon preemption, i.e. baking in the arrangement
established at first execution. (We should also consider capturing the
implicit dependency using i915_sched_add_dependency(), but first we need
to think about the constraints that requires on the execution/retirement
ordering.)
Chris Wilson [Mon, 23 Sep 2019 15:28:43 +0000 (16:28 +0100)]
drm/i915: Fixup preempt-to-busy vs reset of a virtual request
Due to the nature of preempt-to-busy the execlists active tracking and
the schedule queue may become temporarily desync'ed (between resubmission
to HW and its ack from HW). This means that we may have unwound a
request and passed it back to the virtual engine, but it is still
inflight on the HW and may even result in a GPU hang. If we detect that
GPU hang and try to reset, the hanging request->engine will no longer
match the current engine, which means that the request is not on the
execlists active list and we should not try to find an older incomplete
request. Given that we have deduced this must be a request on a virtual
engine, it is the single active request in the context and so must be
guilty (as the context is still inflight, it is prevented from being
executed on another engine as we process the reset).
Chris Wilson [Mon, 23 Sep 2019 15:28:42 +0000 (16:28 +0100)]
drm/i915: Fixup preempt-to-busy vs resubmission of a virtual request
As preempt-to-busy leaves the request on the HW as the resubmission is
processed, that request may complete in the background and even cause a
second virtual request to enter queue. This second virtual request
breaks our "single request in the virtual pipeline" assumptions.
Furthermore, as the virtual request may be completed and retired, we
lose the reference the virtual engine assumes is held. Normally, just
removing the request from the scheduler queue removes it from the
engine, but the virtual engine keeps track of its singleton request via
its ve->request. This pointer needs protecting with a reference.
Clinton A Taylor [Fri, 20 Sep 2019 20:58:07 +0000 (13:58 -0700)]
drm/i915/tgl/pll: Set update_active_dpll
Commit 24a7bfe0c2d7 ("drm/i915: Keep the TypeC port mode fixed when the
port is active") added this new hook while in parallel TGL upstream was
happening and this was missed.
Without this driver will crash when TC DDI is added and driver is
preparing to do a full modeset.
drm/i915/tgl: Finish modular FIA support on registers
If platform supports and has modular FIA is enabled, the registers
bits also change, example: reading TC3 registers with modular FIA
enabled, driver should read from FIA2 but with TC1 bits offsets.
It is described in BSpec 50231 for DFLEXDPSP, other registers don't
have the BSpec description but testing in real hardware have proven
that it had moved for all other registers too.
v2:
- Caching index in tc_phy_fia_idx, instead of calculate it each time
v3:
- Setting tc_phy_fia and tc_phy_fia_idx in the same function
Chris Wilson [Mon, 23 Sep 2019 11:00:56 +0000 (12:00 +0100)]
drm/i915/execlists: Refactor -EIO markup of hung requests
Pull setting -EIO on the hung requests into its own utility function.
Having allowed ourselves to short-circuit submission of completed
requests, we can now do the mark_eio() prior to submission and avoid
some redundant operations.
Chris Wilson [Mon, 23 Sep 2019 11:00:55 +0000 (12:00 +0100)]
drm/i915: Only enqueue already completed requests
If we are asked to submit a completed request, just move it onto the
active-list without modifying it's payload. If we try to emit the
modified payload of a completed request, we risk racing with the
ring->head update during retirement which may advance the head past our
breadcrumb and so we generate a warning for the emission being behind
the RING_HEAD.
v2: Commentary for the sneaky, shared responsibility between functions.
v3: Spelling mistakes and bonus assertion
Chris Wilson [Mon, 23 Sep 2019 11:00:54 +0000 (12:00 +0100)]
drm/i915/execlists: Drop redundant list_del_init(&rq->sched.link)
Since amalgamating the queued and active lists in commit 422d7df4f090
("drm/i915: Replace engine->timeline with a plain list"), performing a
i915_request_submit() will remove the request from the execlists
priority queue.
Chris Wilson [Mon, 23 Sep 2019 11:00:53 +0000 (12:00 +0100)]
drm/i915/execlists: Relax assertion for a pinned context image on reset
A gpu hang can occur at any time, given a sufficiently angry gpu. An
example is when it forgets to perform a context-switch at the end of a
request, leaving us with a hanging GPU on a completed request. Here, we
may retire the request, only leaving its context alive via the active
barrier. When we reset the GPU on a completed request, we do not modify
its context image (just updating the ring state) and can safely defer
the assertion that we have the image pinned and ready to modify.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111639 Fixes: dffa8feb3084 ("drm/i915/perf: Assert locking for i915_init_oa_perf_state()") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190923110056.15176-1-chris@chris-wilson.co.uk
Jani Nikula [Fri, 20 Sep 2019 18:54:19 +0000 (21:54 +0300)]
drm/i915: abstract intel_panel_sanitize_ssc() from intel_modeset_init()
The code is too specific and detailed to have open in a high level
function. Abstract away. As a drive-by improvement switch to using
enableddisabled() in logging and git rid of a redundant !!. No
functional changes.
Jani Nikula [Fri, 20 Sep 2019 18:54:18 +0000 (21:54 +0300)]
drm/i915: pass i915 to intel_modeset_driver_remove()
In general, prefer struct drm_i915_private * over struct drm_device *
when either will do. Rename the local variable to i915. Also propagate
to intel_hpd_poll_fini(). No functional changes.
Kai Vehmanen [Fri, 20 Sep 2019 08:39:18 +0000 (11:39 +0300)]
drm/i915: save AUD_FREQ_CNTRL state at audio domain suspend
When audio power domain is suspended, the display driver must
save state of AUD_FREQ_CNTRL on Tiger Lake and Ice Lake
systems. The initial value of the register is set by BIOS and
is read by driver during the audio component init sequence.
Animesh Manna [Fri, 20 Sep 2019 11:59:28 +0000 (17:29 +0530)]
drm/i915/dsb: Enable gamma lut programming using DSB.
Gamma lut programming can be programmed using DSB
where bulk register programming can be done using indexed
register write which takes number of data and the mmio offset
to be written.
Currently enabled for 12-bit gamma LUT which is enabled by
default and later 8-bit/10-bit will be enabled in future
based on need.
v1: Initial version.
v2: Directly call dsb-api at callsites. (Jani)
v3:
- modified the code as per single dsb instance per crtc. (Shashank)
- Added dsb get/put call in platform specific load_lut hook. (Jani)
- removed dsb pointer from dev_priv. (Jani)
v4: simplified code by dropping ref-count implementation. (Shashank)
Animesh Manna [Fri, 20 Sep 2019 11:59:27 +0000 (17:29 +0530)]
drm/i915/dsb: function to trigger workload execution of DSB.
Batch buffer will be created through dsb-reg-write function which can have
single/multiple request based on usecase and once the buffer is ready
commit function will trigger the execution of the batch buffer. All
the registers will be updated simultaneously.
v1: Initial version.
v2: Optimized code few places. (Chris)
v3: USed DRM_ERROR for dsb head/tail programming failure. (Shashank)
v4: reset ins_start_offset after commit. (Jani)
Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Animesh Manna <animesh.manna@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-8-animesh.manna@intel.com
Animesh Manna [Fri, 20 Sep 2019 11:59:26 +0000 (17:29 +0530)]
drm/i915/dsb: functions to enable/disable DSB engine.
DSB will be used for performance improvement for some special scenario.
DSB engine will be enabled based on need and after completion of its work
will be disabled. Api added for enable/disable operation by using DSB_CTRL
register.
v1: Initial version.
v2: POSTING_READ added after writing control register. (Shashank)
v3: cosmetic changes done. (Shashank)
Cc: Michel Thierry <michel.thierry@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Animesh Manna <animesh.manna@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-7-animesh.manna@intel.com
Animesh Manna [Fri, 20 Sep 2019 11:59:24 +0000 (17:29 +0530)]
drm/i915/dsb: Indexed register write function for DSB.
DSB can program large set of data through indexed register write
(opcode 0x9) in one shot. DSB feature can be used for bulk register
programming e.g. gamma lut programming, HDR meta data programming.
v1: initial version.
v2: simplified code by using ALIGN(). (Chris)
v3: ascii table added as code comment. (Shashank)
v4: cosmetic changes done. (Shashank)
v5: reset ins_start_offset. (Jani)
v6: update ins_start_offset in inel_dsb_reg_write.
Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Animesh Manna <animesh.manna@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-5-animesh.manna@intel.com
Jani Nikula [Mon, 23 Sep 2019 07:09:23 +0000 (10:09 +0300)]
drm/i915/dsb: single register write function for DSB.
DSB support single register write through opcode 0x1. Generic
api created which accumulate all single register write in a batch
buffer and once DSB is triggered, it will program all the registers
at the same time.
v1: Initial version.
v2: Unused macro removed and cosmetic changes done. (Shashank)
v3: set free_pos to zero in dsb-put() instead dsb-get() and
a cosmetic change. (Shashank)
v4: macro of indexed-write is moved. (Shashank)
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Animesh Manna <animesh.manna@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-4-animesh.manna@intel.com
Animesh Manna [Fri, 20 Sep 2019 11:59:22 +0000 (17:29 +0530)]
drm/i915/dsb: DSB context creation.
This patch adds a function, which will internally get the gem buffer
for DSB engine. The GEM buffer is from global GTT, and is mapped into
CPU domain, contains the data + opcode to be feed to DSB engine.
v1: Initial version.
v2:
- removed some unwanted code. (Chris)
- Used i915_gem_object_create_internal instead of _shmem. (Chris)
- cmd_buf_tail removed and can be derived through vma object. (Chris)
v3: vma realeased if i915_gem_object_pin_map() failed. (Shashank)
v4: for simplification and based on current usage added single dsb
object in intel_crtc. (Shashank)
v5: seting NULL to cmd_buf moved outside of mutex in dsb-put(). (Shashank)
v6:
- refcount machanism added.
- Used atomic_add_return and atomic_dec_and_test instead of
atomic_inc and atomic_dec. (Jani)
Cc: Imre Deak <imre.deak@intel.com> Cc: Michel Thierry <michel.thierry@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[Jani: added #include <linux/types.h> while pushing] Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190920115930.27829-3-animesh.manna@intel.com
For icl+, have hw read out to create hw blob of gamma
lut values. icl+ platforms supports multi segmented gamma
mode by default, add hw lut creation for this mode.
This will be used to validate gamma programming using dsb
(display state buffer) which is a tgl specific feature.
Major change done-removal of readouts of coarse and fine segments
because PAL_PREC_DATA register isn't giving propoer values.
State checker limited only to "fine segment"
v2: -readout code for multisegmented gamma has to come
up with some intermediate entries that aren't preserved
in hardware (Jani N)
-linear interpolation (Ville)
-moved common code to check gamma_enable to specific funcs,
since icl doesn't support that
v3: -use u16 instead of __u16 [Jani N]
-used single lut [Jani N]
-improved and more readable for loops [Jani N]
-read values directly to actual locations and then fill gaps [Jani N]
-moved cleaning to patch 1 [Jani N]
-renamed icl_read_lut_multi_seg() to icl_read_lut_multi_segment to
make it similar to icl_load_luts()
-renamed icl_compute_interpolated_gamma_blob() to
icl_compute_interpolated_gamma_lut_values() more sensible, I guess
v4: -removed interpolated func for creating gamma lut values
-removed readouts of fine and coarse segments, failure to read PAL_PREC_DATA
correctly
Gen12 has dual-subslices (DSS), which compared to gen11 subslices have
some duplicated resources/paths. Although DSS behave similarly to 2
subslices, instead of splitting this and presenting userspace with bits
not directly representative of hardware resources, present userspace
with a subslice_mask made up of DSS bits instead.
v2: GEM_BUG_ON on mask size (Lionel)
Bspec: 29547
Bspec: 12247 Cc: Kelvin Gardiner <kelvin.gardiner@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com> CC: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Cc: Michel Thierry <michel.thierry@intel.com> #v1 Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Signed-off-by: James Ausmus <james.ausmus@intel.com> Signed-off-by: Oscar Mateo <oscar.mateo@intel.com> Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com> Signed-off-by: Stuart Summers <stuart.summers@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190913075137.18476-2-chris@chris-wilson.co.uk Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Thu, 18 Jul 2019 14:50:53 +0000 (17:50 +0300)]
drm/i915: Add PIPECONF YCbCr 4:4:4 programming for ILK-IVB
On ILK-IVB the pipe colorspace is configured via PIPECONF
(as opposed to PIPEMISC in BDW+). Let's configure+readout
that stuff correctly.
Enabling YCbCr 4:4:4 output will now be a simple matter of
setting crtc_state->output_format appropriately in the encoder
.compute_config(). However, when we do that we must be
aware of the fact that YCbCr DP output doesn't seem to work
on ILK (resulting image is totally garbled), but on SNB+
it works fine. However HDMI YCbCr output does work correctly
even on ILK.
Ville Syrjälä [Thu, 18 Jul 2019 14:50:52 +0000 (17:50 +0300)]
drm/i915: Set up ILK/SNB csc unit properly for YCbCr output
Prepare the pipe csc for YCbCr output on ilk/snb. The main difference
to IVB+ is the lack of explicit post offsets, and instead we must
configure the CSC info RGB->YUV mode (which takes care of offsetting
Cb/Cr properly) and enable the "black screen offset" bit to add the
required offset to Y.
And while at it throw some comments around the bit defines to
document which platforms have which bits.
projects / kernel.git / log