Ville Syrjälä [Wed, 28 Oct 2020 21:33:07 +0000 (23:33 +0200)]
drm/i915: Give DDI encoders even better names
Let's pimp the DDI encoder->name to reflect what the spec calls them.
Ie. on pre-tgl DDI A-F, on tgl+ DDI A-C or DDI TC1-6.
Also since each encoder is really a combination of the DDI and the PHY
we include the PHY name as well.
ICL is a bit special since it already has the two different types
of DDIs (combo or TC) but it still calls them just DDI A-F regarless
of the type. For that let's add an extra "(TC)" note to remind
is which type of DDI it really is.
The code is darn ugly, but not sure there's much we can do about it.
Imre Deak [Tue, 27 Oct 2020 16:09:28 +0000 (18:09 +0200)]
drm/i915: Fix encoder lookup during PSR atomic check
The atomic check hooks must look up the encoder to be used with a
connector from the connector's atomic state, and not assume that it's
the connector's current attached encoder. The latter one can change
under the atomic check func, or can be unset yet as in the case of MST
connectors.
Lucas De Marchi [Tue, 27 Oct 2020 04:46:17 +0000 (21:46 -0700)]
drm/i915/display: remove debug message from error path
First check in the function is if swsci() is supported. All the error
paths are easy to figure out the reason, so remove the extra debug
message: it's normal not to support swsci() e.g. in dgfx.
v2: Rather than special case dgfx, just remove the debug message
(from Ville)
Clinton A Taylor [Wed, 21 Oct 2020 08:20:30 +0000 (01:20 -0700)]
drm/i915/dg1: invert HPD pins
HPD pins are inverted for DG1 platform.
Bspec: 49956 Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201021082034.3170478-3-lucas.demarchi@intel.com
Lucas De Marchi [Wed, 21 Oct 2020 08:20:29 +0000 (01:20 -0700)]
drm/i915/dg1: add hpd interrupt handling
DG1 has one more combo phy port, no TC and all irq handling goes through
SDE, like for MCC.
v2: Also change intel_hpd_pin_default() to include DG1 mapping
v3, v4: Rebase on hpd refactor
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Anshuman Gupta <anshuman.gupta@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Imre Deak <imre.deak@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201021082034.3170478-2-lucas.demarchi@intel.com
drm/i915/tgl/psr: Fix glitches when doing frontbuffer modifications
Writes to CURSURFLIVE in TGL are causing IOMMU errors and visual
glitches that are often reproduced when executing CPU intensive
workloads while a eDP 4K panel is attached.
Manually exiting PSR causes the frontbuffer to be updated without
glitches and the IOMMU errors are also gone but this comes at the cost
of less time with PSR active.
So using this workaround until this issue is root caused and a better
fix is found.
The current code is already ready to enable PSR after this exit if
there is not other frontbuffer modifications.
Adding a new if block in psr_force_hw_tracking_exit() instead of reuse
the else/gen8- block because the plan is to revert this workaround
as soon as a better solution is found.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Tested-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201002231627.24528-1-jose.souza@intel.com
The block comment for cnl_program_nearest_filter_coefs() has a wonderful
diagram, but although it is marked up as kerneldoc does not use the
markup for providing the function definition.
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'dev_priv' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'pipe' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'id' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'set' not described in 'cnl_program_nearest_filter_coefs'
Ville Syrjälä [Wed, 21 Oct 2020 13:14:43 +0000 (16:14 +0300)]
drm/i915: Clean up the irq enable/disable for ilk rps
Let's unmask the PCU event irq _after_ we've set up the
hardware and software to deal with the fallout. We can
also drop the PCU event bit from DEIER except when we
need it for rps.
And on the disable side we replace the hand rolled (and
unlocked) DEIER/IIR/IMR frobbing with ilk_disable_display_irq().
Ocd does require me to reorder it to be symmetric with
the enable path however.
Ville Syrjälä [Wed, 21 Oct 2020 13:14:41 +0000 (16:14 +0300)]
drm/i915: Fix potential overflows in ilk ips calculations
A bunch of the ips calculations require 64bit math. In particular
'corr' and 'corr2' look like they can overflow on 32bit systems.
Switch to explicit u64 for those.
Ville Syrjälä [Wed, 21 Oct 2020 13:14:40 +0000 (16:14 +0300)]
drm/i915: Read actual GPU frequency from MEMSTAT_ILK on ILK
There is no GEN6_RPSTAT1 on ILK. Instead of reading that let's
try to get the same information from MEMSTAT_ILK. At least it
seems to track MEMSWCTL frequency request perfectly on my ILK.
It needs the same invert trick as the request value.
We don't want to put the invert thing into intel_gpu_freq()
and intel_freq_opcode() because that would incorrectly invert
the min/max/etc frequencies also.
One day someone might want to reverse engineer the formula for
converting these numbers to Hz, but for now we'll just report
them raw.
Ville Syrjälä [Wed, 21 Oct 2020 13:14:39 +0000 (16:14 +0300)]
drm/i915: Restore ILK-M RPS support
Restore RPS for ILK-M. We lost it when an extra HAS_RPS()
check appeared in intel_rps_enable().
Unfortunaltey this just makes the performance worse on my
ILK because intel_ips insists on limiting the GPU freq to
the minimum. If we don't do the RPS init then intel_ips will
not limit the frequency for whatever reason. Either it can't
get at some required information and thus makes wrong decisions,
or we mess up some weights/etc. and cause it to make the wrong
decisions when RPS init has been done, or the entire thing is
just wrong. Would require a bunch of reverse engineering to
figure out what's going on.
Pankaj Bharadiya [Tue, 20 Oct 2020 16:14:26 +0000 (21:44 +0530)]
drm/i915: Enable scaling filter for plane and CRTC
GEN >= 10 hardware supports the programmable scaler filter.
Attach scaling filter property for CRTC and plane for GEN >= 10
hardwares and program scaler filter based on the selected filter
type.
changes since v3:
* None
changes since v2:
* Use updated functions
* Add ps_ctrl var to contain the full PS_CTRL register value (Ville)
* Duplicate the scaling filter in crtc and plane hw state (Ville)
changes since v1:
* None
Changes since RFC:
* Enable properties for GEN >= 10 platforms (Ville)
* Do not round off the crtc co-ordinate (Danial Stone, Ville)
* Add new functions to handle scaling filter setup (Ville)
* Remove coefficient set 0 hardcoding.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-5-pankaj.laxminarayan.bharadiya@intel.com
Pankaj Bharadiya [Tue, 20 Oct 2020 16:14:25 +0000 (21:44 +0530)]
drm/i915/display: Add Nearest-neighbor based integer scaling support
Integer scaling (IS) is a nearest-neighbor upscaling technique that
simply scales up the existing pixels by an integer
(i.e., whole number) multiplier.Nearest-neighbor (NN) interpolation
works by filling in the missing color values in the upscaled image
with that of the coordinate-mapped nearest source pixel value.
Both IS and NN preserve the clarity of the original image. Integer
scaling is particularly useful for pixel art games that rely on
sharp, blocky images to deliver their distinctive look.
Introduce functions to configure the scaler filter coefficients to
enable nearest-neighbor filtering.
Bspec: 49247
changes since v6:
* Trust compiler, remove pointless inline keyword from cnl_coef_tap()
& cnl_nearest_filter_coef() functions (Ville)
changes since v4:
* Make cnl_coef_tap(), cnl_nearest_filter_coef() inline (Uma)
changes since v3:
* None
changes since v2:
* Move APIs from 5/5 into this patch.
* Change filter programming related function names to cnl_*, move
filter select bits related code into inline function (Ville)
changes since v1:
* Rearrange skl_scaler_setup_nearest_neighbor_filter() to iterate the
registers directly instead of the phases and taps (Ville)
changes since RFC:
* Refine the skl_scaler_setup_nearest_neighbor_filter() logic (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-4-pankaj.laxminarayan.bharadiya@intel.com
Pankaj Bharadiya [Tue, 20 Oct 2020 16:14:24 +0000 (21:44 +0530)]
drm/i915: Introduce scaling filter related registers and bit fields
Introduce scaler registers and bit fields needed to configure the
scaling filter in prgrammed mode and configure scaling filter
coefficients.
changes since v3:
* None
changes since v2:
* Change macro names to CNL_* and use +(set)*8 instead of adding
another trip through _PICK_EVEN (Ville).
changes since v1:
* None
changes since RFC:
* Parametrize scaler coeffient macros by 'set' (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-3-pankaj.laxminarayan.bharadiya@intel.com
Pankaj Bharadiya [Tue, 20 Oct 2020 16:14:23 +0000 (21:44 +0530)]
drm: Introduce plane and CRTC scaling filter properties
Introduce per-plane and per-CRTC scaling filter properties to allow
userspace to select the driver's default scaling filter or
Nearest-neighbor(NN) filter for upscaling operations on CRTC and
plane.
Drivers can set up this property for a plane by calling
drm_plane_create_scaling_filter() and for a CRTC by calling
drm_crtc_create_scaling_filter().
NN filter works by filling in the missing color values in the upscaled
image with that of the coordinate-mapped nearest source pixel value.
NN filter for integer multiple scaling can be particularly useful for
for pixel art games that rely on sharp, blocky images to deliver their
distinctive look.
changes since: v6:
* Move property doc to existing "Standard CRTC Properties" and
"Plane Composition Properties" doc comments (Simon)
changes since v3:
* Refactor code, add new function for common code (Ville)
changes since v2:
* Create per-plane and per-CRTC scaling filter property (Ville)
changes since v1:
* None
changes since RFC:
* Add separate properties for plane and CRTC (Ville)
Manasi Navare [Thu, 8 Oct 2020 21:45:26 +0000 (14:45 -0700)]
drm/i915/display: Rename pipe_timings to transcoder_timings
No functional changes in this patch.
With Bigjoiner, there are 2 pipes driving 2 halfs of 1
transcoder. The transcoder_mode has the full timings, and is used
for configuring the transcoder with the intended mode after
joining the 2 halves.
To clear the confusion, we rename intel_set_pipe_timings to
intel_set_transcoder_timings
v2:
* Split the renaming into separate patch (Ville)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Animesh Manna <animesh.manna@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201008214535.22942-2-manasi.d.navare@intel.com
Ville Syrjälä [Tue, 13 Oct 2020 18:11:37 +0000 (21:11 +0300)]
drm/i915: Reorder hpd init vs. display resume
Currently we call .hpd_irq_setup() directly just before display
resume, and follow it with another call via intel_hpd_init()
just afterwards. Assuming the hpd pins are marked as enabled
during the open-coded call these two things do exactly the
same thing (ie. enable HPD interrupts). Which even makes sense
since we definitely need working HPD interrupts for MST sideband
during the display resume.
So let's nuke the open-coded call and move the intel_hpd_init()
call earlier. However we need to leave the poll_init_work stuff
behind after the display resume as that will trigger display
detection while we're resuming. We don't want that trampling over
the display resume process. To make this a bit more symmetric
we turn this into a intel_hpd_poll_{enable,disable}() pair.
So we end up with the following transformation:
intel_hpd_poll_init() -> intel_hpd_poll_enable()
lone intel_hpd_init() -> intel_hpd_init()+intel_hpd_poll_disable()
.hpd_irq_setup()+resume+intel_hpd_init() -> intel_hpd_init()+resume+intel_hpd_poll_disable()
If we really would like to prevent all *long* HPD processing during
display resume we'd need some kind of software mechanism to simply
ignore all long HPDs. Currently we appear to have that just for
fbdev via ifbdev->hpd_suspended. Since we aren't exploding left and
right all the time I guess that's mostly sufficient.
For a bit of history on this, we first got a mechanism to block
hotplug processing during suspend in commit 17dbd0c24d32 ("drm/i915:
enable irqs earlier when resuming") on account of moving the irq enable
earlier. This then got removed in commit 545480c5c811 ("drm/fb-helper:
Fix hpd vs. initial config races") because the fdev initial config
got pushed to a later point. The second ad-hoc hpd_irq_setup() for
resume was added in commit 266e4ae46a17 ("drm/i915: add DP 1.2 MST
support (v0.7)") to be able to do MST sideband during the resume.
And finally we got a partial resurrection of the hpd blocking
mechanism in commit 4ff1afc3e79d ("drm/i915: Block fbdev HPD
processing during suspend"), but this time it only prevent fbdev
from handling hpd while resuming.
v2: Leave the poll_init_work behind
v3: Remove the extra intel_hpd_poll_disable() from display reset (Lyude)
Add the missing intel_hpd_poll_disable() to display init (Imre)
Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.
Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.
Ville Syrjälä [Fri, 16 Oct 2020 19:47:59 +0000 (22:47 +0300)]
drm/i915: Move the lspcon resume from .reset() to intel_dp_sink_dpms()
Rather that try to trick LSPCON back into PCON mode from the .reset()
hook let's just do that as a regular part of the normal modeset
sequence, which is going to take care of the system resume case. During
a normal modeset this should normally be a nop as the mode should have
already been switched by .detect().
Chris Wilson [Tue, 11 Aug 2020 09:25:32 +0000 (10:25 +0100)]
drm/i915: Drop runtime-pm assert from vgpu io accessors
The "mmio" writes into vgpu registers are simple memory traps from the
guest into the host. We do not need to assert in the guest that the
device is awake for the io as we do not write to the device itself.
However, over time we have refactored all the mmio accessors with the
result that the vgpu reuses the gen2 accessors and so inherits the
assert for runtime-pm of the native device. The assert though has
actually been there since commit 615b8a8acd1a ("drm/i915: Create vGPU
specific MMIO operations to reduce traps").
Chris Wilson [Mon, 19 Oct 2020 10:15:23 +0000 (11:15 +0100)]
drm/i915: Force VT'd workarounds when running as a guest OS
If i915.ko is being used as a passthrough device, it does not know if
the host is using intel_iommu. Mixing the iommu and gfx causes a few
issues (such as scanout overfetch) which we need to workaround inside
the driver, so if we detect we are running under a hypervisor, also
assume the device access is being virtualised.
Reported-by: Stefan Fritsch <sf@sfritsch.de> Suggested-by: Stefan Fritsch <sf@sfritsch.de> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Stefan Fritsch <sf@sfritsch.de> Cc: stable@vger.kernel.org Tested-by: Stefan Fritsch <sf@sfritsch.de> Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201019101523.4145-1-chris@chris-wilson.co.uk
Underruns happens when plane height + y offset is not a modulo of 4
when FBC is enabled. It happens when scanline is at vactive - 10 but
that is not feasible to do from the software side so here completely
disabling FBC when height + y offset matches to avoid visual glitches.
Specification says that it only affects TGL display C stepping and
newer but to simply the check and as TGL is already in final costumers
hands, pre-production display stepping A and B was also included.
Ville Syrjälä [Thu, 24 Sep 2020 18:41:56 +0000 (21:41 +0300)]
drm/i915: Inline intel_dp_ycbcr420_config()
intel_dp_ycbcr420_config() is rather pointless. Just inline it
directly into intel_dp_compute_config(). This gets rid of the
ugly double assignment of output_format.
Not really sure what the best policy would be when the user
supplies a mode classified by the display as "YCbCr 4:2:0
only", but we know that we can't do YCbCr 4:2:0 output. For
now keep the current behaviour of just silently upgrade
it to RGB 4:4:4.
Ville Syrjälä [Thu, 24 Sep 2020 18:41:55 +0000 (21:41 +0300)]
drm/i915: Nuke lspcon_ycbcr420_config()
Remove the lspcon special case from intel_dp_compute_config() and
just treat it like any other DFP than can do 4:4:4->4:2:0 conversion.
The only difference between the two codepaths was that the lspcon
code tried to already halve port_clock. That was just total nonsense
as we hadn't even computed the base port_clock at that time.
All that stuff happens intel_dp_compute_link_config*() and it
already takes care of the 4:2:0 clock reduction.
Ville Syrjälä [Thu, 24 Sep 2020 18:41:54 +0000 (21:41 +0300)]
drm/i915: Nuke lspcon_downsampling
crtc_state->lspcon_downsampling isn't particularly useful at
the moment since we can't even do proper readout for it.
Let's get rid of it. Will help with unifying the LSPCON with
the regular DFP YCbCr output support.
Ville Syrjälä [Wed, 7 Oct 2020 12:03:27 +0000 (15:03 +0300)]
drm/i915: Mark initial fb obj as WT on eLLC machines to avoid rcu lockup during fbdev init
Currently we leave the cache_level of the initial fb obj
set to NONE. This means on eLLC machines the first pin_to_display()
will try to switch it to WT which requires a vma unbind+bind.
If that happens during the fbdev initialization rcu does not
seem operational which causes the unbind to get stuck. To
most appearances this looks like a dead machine on boot.
Avoid the unbind by already marking the object cache_level
as WT when creating it. We still do an excplicit ggtt pin
which will rewrite the PTEs anyway, so they will match whatever
cache level we set.
Ville Syrjälä [Thu, 16 Jul 2020 19:04:26 +0000 (22:04 +0300)]
drm/i915: Apply WAC6entrylatency to kbl/cfl
WAC6entrylatency is trying to fix excessive rc6 entry latency caused
by the extra delay from FBC_LLC_READ_CTRL, which is there for some
extra sync with uncore for frame buffer caching in LLC.
Reading through the hsd the recommendation was to set the FBC_LLC_FULLY_OPEN
bit to disable this extra delay entirely. This can be done whenever fb LLC
caching is not used. The alternative suggestion was to reduce the delay to
eg. 0x5 via updated BIOS programming instructions. But all the kbl/cfl
machines I've seen still have the default 0xff programmed. As we never use
fb LLC caching let's just apply the w/a to all skl derivatives to get
consistent rc6 latencies.
I was able to measure the effect of FBC_LLC_READ_CTRL to rc6 latency
via forcewake. Here's a graph of some of the results:
The default FBC_LLC_READ_CTRL value of 0xff is documented to give us
a 170usec delay. That tracks well with the knees at 0xffff->~44msec and
0x8000->~22msec we see in the graph.
We can see that if we sleep longer than the FBC_LLC_READ_CTRL delay
we always observe the full (~145usec) rc6 wakeup latency. But if we sleep
for less than the FBC_LLC_READ_CTRL delay we see a quicker fw wakeup,
presumably due the hardware not having yet entered rc6 fully.
The other plateaus in the graph I suspect correspond to some shallower
internal rc states.
Matt Roper [Thu, 15 Oct 2020 22:00:38 +0000 (15:00 -0700)]
drm/i915/rkl: Add new cdclk table
A recent bspec update has provided a new cdclk table for RKL. All of
the cdclk values are the same as those we've been using on ICL, TGL,
etc., but we obtain them by doubling both the PLL ratio and CD2X divider
numbers.
Anshuman Gupta [Wed, 14 Oct 2020 19:19:36 +0000 (12:19 -0700)]
drm/i915/dg1: Update DMC_DEBUG register
Update the DMC_DEBUG_DC5 register to its new location and do not try
reading the DC6 counter since DG1 doesn't support DC6.
v2: Use IS_DGFX() instead of IS_DG1(). Even if not having DC6 is not
directly related to DGFX, the register move to a new location is. So in
future, if there is one supporting DC6, it would just need to add the
other register rather than fixing the case of a wrong register being
read (Matt)
Stuart Summers [Wed, 14 Oct 2020 19:19:34 +0000 (12:19 -0700)]
drm/i915/dg1: Add initial DG1 workarounds
DG1 shares some workarounds with TGL and RKL and also has some
additional workarounds of its own.
v2: Correct location of Wa_1408615072 (JohnH).
v3: Apply WAs 1606700617, 18011464164 and 22010931296 to DG1 (José)
v4 (Anusha)
- Add Wa_22010271021
- s/Wa_14010096844/Wa_1409836686
v5:
- Extend Wa_14010919138 to all revs (Matt Atwood)
- Power gate media is global gen12 design. (Rodrigo)
- Rebase (Lucas)
v6: use REG_BIT() to fix checkpatch warning (Lucas)
BSpec: 53508
Cc: Matt Atwood <matthew.s.atwood@intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Signed-off-by: Stuart Summers <stuart.summers@intel.com> Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-8-lucas.demarchi@intel.com
Lucas De Marchi [Wed, 14 Oct 2020 19:19:32 +0000 (12:19 -0700)]
drm/i915/dg1: Enable DPLL for DG1
Add DG1 DPLL Enable register macro and use the macro to enable the
correct DPLL based on PLL id. Although we use
_MG_PLL1_ENABLE/_MG_PLL2_ENABLE these are rather combo phys.
While at it, fix coding style: wrong newlines and use if/else chain
v2: Rewrite original patch from Aditya Swarup based on refactors
upstream
Aditya Swarup [Wed, 14 Oct 2020 19:19:31 +0000 (12:19 -0700)]
drm/i915/dg1: Add and setup DPLLs for DG1
Add entries for dg1 plls and setup dg1_pll_mgr to reuse ICL callbacks.
Initial setup for shared dplls DPLL0/1 for DDIA/DDIB and DPLL2/3 for
DDI-TC1/DDI-TC2. Configure dpll cfgcrx registers to drive the plls on
DG1.
v2 (Lucas): Reword commit message and add missing update_ref_clks hook
(requested by Matt Roper)
Lucas De Marchi [Wed, 14 Oct 2020 19:19:28 +0000 (12:19 -0700)]
drm/i915/cnl: skip PW_DDI_F on certain skus
The skus guarded by IS_CNL_WITH_PORT_F() have port F and thus they need
those power wells. The others don't have those. Up to now we were
just overriding the number of power wells on !IS_CNL_WITH_PORT_F(),
relying on those power wells to be the last ones. Now that we have logic
in place to skip power wells by id, use it instead.
Aditya Swarup [Wed, 14 Oct 2020 19:19:27 +0000 (12:19 -0700)]
drm/i915/display: allow to skip certain power wells
This allows us to skip power wells on a platform allowing it to re-use
the table from another one instead of having to create a new table from
scratch that is basically a copy with a few removals.
Cc: Imre Deak <imre.deak@intel.com> Suggested-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
[ Adapt ignore logic to be based on pw id rather than adding a new
field, as suggested by Imre ] Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201014191937.1266226-1-lucas.demarchi@intel.com
Tejas Upadhyay [Tue, 13 Oct 2020 19:29:48 +0000 (00:59 +0530)]
drm/i915/jsl: Split EHL/JSL platform info and PCI ids
Recently we came across requirement to identify EHL and JSL
platform to program them differently. Thus Split the basic
platform definition, macros, and PCI IDs to differentiate
between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced
with IS_JSL_EHL everywhere.
Changes since V1 :
- Rebased to avoid merge conflicts
- Added missed check for jasperlake in intel_uc_fw.c
Aaron Ma [Fri, 9 Oct 2020 08:57:50 +0000 (16:57 +0800)]
drm/i915: Force DPCD backlight mode for BOE 2270 panel
BOE 2270 panel failed to control backlight brightness.
Add it in edid quirks to force using DPCD backlight control.
Then the brightness can be controlled.
Sean Paul [Fri, 18 Sep 2020 00:28:42 +0000 (20:28 -0400)]
drm/i915/dp: Tweak initial dpcd backlight.enabled value
In commit f8af9e66566d ("drm/i915: Assume 100% brightness when not in
DPCD control mode"), we fixed the brightness level when DPCD control was
not active to max brightness. This is as good as we can guess since most
backlights go on full when uncontrolled.
However in doing so we changed the semantics of the initial
'backlight.enabled' value. At least on Pixelbooks, they were relying
on the brightness level in DP_EDP_BACKLIGHT_BRIGHTNESS_MSB to be 0 on
boot such that enabled would be false. This causes the device to be
enabled when the brightness is set. Without this, brightness control
doesn't work. So by changing brightness to max, we also flipped enabled
to be true on boot.
To fix this, make enabled a function of brightness and backlight control
mechanism.
Fixes: f8af9e66566d ("drm/i915: Assume 100% brightness when not in DPCD control mode") Cc: Lyude Paul <lyude@redhat.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com> Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Kevin Chowski <chowski@chromium.org>> Signed-off-by: Sean Paul <seanpaul@chromium.org> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200918002845.32766-1-sean@poorly.run
Imre Deak [Wed, 7 Oct 2020 17:09:17 +0000 (20:09 +0300)]
drm/i915: Switch to LTTPR non-transparent mode link training
The DP Standard's recommendation is to use the LTTPR non-transparent
mode link training if LTTPRs are detected, so let's do this.
Besides power-saving, the advantages of this are that the maximum number
of LTTPRs can only be used in non-transparent mode (the limit is 5-8 in
transparent mode), and it provides a way to narrow down the reason for a
link training failure to a given link segment. Non-transparent mode is
probably also the mode that was tested the most by the industry.
The changes in this patchset:
- Pass the DP PHY that is currently link trained to all LT helpers, so
that these can access the correct LTTPR/DPRX DPCD registers.
- During LT take into account the LTTPR common lane rate/count and the
per LTTPR-PHY vswing/pre-emph limits.
- Switch to LTTPR non-transparent LT mode and train each link segment
according to the sequence in DP Standard v2.0 (complete CR/EQ for
each segment before continuing with the next segment).
v2:
- Switch to non-transparent mode during connector detection, which is
required before reading the per-PHY LTTPR capabilities.
- Move the DP_PHY_LTTPR() macro to drm_dp_helper.h (Ville)
- Use the new drm_dp_dpcd_read_phy_link_status() instead of adding the
same logic to intel_dp_get_link_status(). (Ville)
- Make intel_dp_lttpr_phy_caps() return a pointer to the whole array
instead of a pointer to its first element. (Ville)
- Add the intel_dp_phy_is_downstream_of_source() helper. (Ville)
- Add a code comment about the disable->enable quirk of
non-transparent mode.
- Add the intel_dp_training_pattern_set_reg() helper.
- Fix checkpatch/sparse warns.
Imre Deak [Wed, 7 Oct 2020 17:09:16 +0000 (20:09 +0300)]
drm/i915: Switch to LTTPR transparent mode link training
By default LTTPRs should be in transparent link training mode,
nevertheless in this patch we switch to this default mode explicitly.
The DP Standard recommends this, supposedly because an LTTPR may be left
in the non-transparent mode (by BIOS, previous kernel, or after reset
due to a firmware bug). I haven't seen this happening, but let's follow
the DP Standard.
v2:
- Add a code comment about the explicit disabling of non-transparent
mode.
v3:
- Move check to prevent initing LTTPRs on eDP to init_dp_lttpr_init().
Imre Deak [Wed, 7 Oct 2020 17:09:15 +0000 (20:09 +0300)]
drm/dp: Add LTTPR helpers
Add the helpers and register definitions needed to read out the common
and per-PHY LTTPR capabilities and perform link training in the LTTPR
non-transparent mode.
v2:
- Add drm_dp_dpcd_read_phy_link_status() and DP_PHY_LTTPR() here instead
of adding these to i915. (Ville)
v3:
- Use memmove() to convert LTTPR to DPRX link status format. (Ville)
Cc: dri-devel@lists.freedesktop.org Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Lyude Paul <lyude@redhat.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-5-imre.deak@intel.com
Imre Deak [Wed, 7 Oct 2020 17:09:14 +0000 (20:09 +0300)]
drm/i915: Factor out a helper to disable the DPCD training pattern
To prepare for a follow-up LTTPR change factor out a helper to disable
the training pattern in DPCD. We'll need to do this for each LTTPR
(without programming the port to output the idle pattern) when training
in LTTPR non-transparent mode.
While at it also move the disable-link-training logic from
intel_dp_set_link_train() to intel_dp_stop_link_train(), since the
latter is the only user of this.
v2:
- Move the disable-link-training logic to intel_dp_stop_link_train()
(Ville)
Imre Deak [Wed, 7 Oct 2020 17:09:13 +0000 (20:09 +0300)]
drm/i915: Simplify the link training functions
Split the prepare, link training, fallback-handling steps into their own
functions for clarity and as a preparation for the upcoming LTTPR
changes.
While at it also:
- Unexport and inline intel_dp_set_idle_link_train(), which is used at a
single place.
- Add some documentation to functions that are exported or that can use
a better description about which part of the LT sequence they
implement.
v2: (Ville)
- Unexport/inline intel_dp_set_idle_link_train()
- Make the documentation of
intel_dp_prepare_link_train()/intel_dp_stop_link_train() more accurate
wrt. HW specific details.
Imre Deak [Wed, 7 Oct 2020 17:09:12 +0000 (20:09 +0300)]
drm/i915: Fix DP link training pattern mask
An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.
Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.
v2:
- Use a helper instead of open-coding the masking. (Ville)
Matt Roper [Fri, 9 Oct 2020 19:44:42 +0000 (12:44 -0700)]
drm/i915: Update gen12 multicast register ranges
The updated bspec forcewake table also provides us with new multicast
ranges that should be reflected in our workaround code.
Note that there are different types of multicast registers with
different styles of replication and different steering registers. The
i915 MCR range lists we're updating here are only used to ensure we can
verify workarounds properly (i.e., if we can't steer register reads we
don't want to verify workarounds where an unsteered read might hit a
fused-off instance of the unit). Because of this, we don't need to
include any of the multicast ranges where all instances of the register
will always present and fusing doesn't play a role. Specifically, that
means that we are not including the MCR ranges designated as "SQIDI" in
the bspec.
Matt Roper [Fri, 9 Oct 2020 19:44:41 +0000 (12:44 -0700)]
drm/i915: Update gen12 forcewake table
The bspec's forcewake page was very stale and out of date for recent
platforms. The hardware team finally provided us with an updated gen12
table (which applies to TGL, RKL, and DG1) and there are a lot of
changes.
v2:
- Add comments showing the subregions of ranges that we've combined for
ease of code review. (Jose)
- Rebase on the s/FORCEWAKE_BLITTER/FORCEWAKE_GT/ patch
Matt Roper [Fri, 9 Oct 2020 19:44:40 +0000 (12:44 -0700)]
drm/i915: Rename FORCEWAKE_BLITTER to FORCEWAKE_GT
The power well that we've been referring to as the 'blitter' well is
actually more of a general GT power well which contains a lot of things
other than the blitter engine registers. The FORCEWAKE_BLITTER name in
the code was used for historic reasons, but no longer matches how the
bspec describes this power well and just causes confusion for people not
familiar with this area of the code. Let's rename it to FORCEWAKE_GT to
more accurately describe the role of the power well and match how the
modern bspec refers to it.
v2:
- Add a comment noting that the GT power well includes the blitter
engine. (Jose)
drm/i915/display: Program PSR2 selective fetch registers
Another step towards PSR2 selective fetch, here programming plane
selective fetch registers and MAN_TRK_CTL enabling selective fetch but
for now it is fetching the whole area of the planes.
The damaged area calculation will come as next and final step.
v2:
- removed warn on when no plane is visible in state
- removed calculations using plane damaged area in
intel_psr2_program_plane_sel_fetch()
v3:
- do not shift 16 positions the plane dst coordinates, only src is
shifted
v4:
- only setting PLANE_SEL_FETCH_CTL_ENABLE and MCURSOR_MODE in
PLANE_SEL_FETCH_CTL
drm/i915/display: Check PSR parameter and flag only in state compute phase
Due to the debugfs flag, has_psr2 in CRTC state could have a different
value than psr.psr2_enabled and it was causing PSR2 subfeatures(DC3CO
and selective fetch) to be set to not a expected state.
So here only taking in consideration the parameter and debugfs flag
when computing PSR state, this way the CRTC state will also have
the correct state.
intel_psr_fastset_force() was already broken as
intel_psr_compute_config() was already only enabling PSR when
psr_global_enabled() and all other PSR requirements are met.
So some changes was required in this function, now it iterates over
all connectors, if it is a eDP connector and is active force a modeset
in the CRTC driving this connector, what will cause the new PSR state
to be set based on the debugfs flag.
drm/i915/vbt: Update the version and expected size of BDB_GENERAL_DEFINITIONS map
This will remove the "Expected child device config size for VBT
version 235 not known" debug message seen in TGL, although this is not
fixing anything it good to keep our VBT parser updated.
Child min_brightness is obsolete from VBT 234+, instead the new
min_brightness field in the main structure should be used.
This new field is 16 bits wide, so backlight_precision_bits is needed
to check if value needs to be scaled down but it is only available in
VBT 236+ so working around it by using the also new backlight_level
in the main struct.
v2:
- missed that backlight_data->level is also obsolete
v3:
- s/backlight/brightness to better match specification
- using u16 to specify brightness level instead of a u32 : 16
Ville Syrjälä [Fri, 9 Oct 2020 12:00:28 +0000 (15:00 +0300)]
drm/i915: Skip aux plane stuff when there is no aux plane
when the hardware isn't going to use the aux plane there's no
real point in dealing with the relevant hardware restrictions.
So let's just skip all that when not necessary.
We can now also remove the offset=~0xfff behaviour for unused
color planes. Let's just zero out everyting so as to not leave
stale garbage behind to confuse people debugging the code.
v2: Explicitly set AUX_DIST to zero when there is no aux plane
Ville Syrjälä [Thu, 8 Oct 2020 10:16:06 +0000 (13:16 +0300)]
drm/i915: Set all unused color plane offsets to ~0xfff again
When the number of potential color planes grew to 4 we stopped
setting all unused color plane offsets to ~0xfff. The code
still tries to do this, but actually does nothing since the
loop limits are bogus.
skl_check_main_surface() actually depends on this ~0xfff
behaviour as it will make sure to move the main surface
offset below the aux surface offset because the hardware
AUX_DIST must be a non-negative value [1], and for simplicity
it doesn't bother checking if the AUX plane is actually
needed or not. So currently it may end up shuffling the
main surface around based on some stale leftover AUX offset.
The skl+ plane code also just blindly calculates the AUX_DIST
whether or not the AUX plane is actually needed by the hw or
not, and that too will now potentially use some stale AUX
surface offset in the calculation. Would seem nicer to
guarantee a consistent non-negative AUX_DIST always.
So bring back the original ~0xfff offset behaviour for
unused color planes. Though it doesn't seem super likely
that this inconsistency would cause any real issues.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Fixes: aec23a1c131f ("drm/i915/tgl: Gen-12 display can decompress surfaces compressed by the media engine") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201008101608.8652-1-ville.syrjala@linux.intel.com Reviewed-by: Imre Deak <imre.deak@intel.com>
Ville Syrjälä [Mon, 5 Oct 2020 17:14:41 +0000 (20:14 +0300)]
drm/i915: Rename i915_{save,restore}_state()
i915_{save,restore}_state() are actually all about the display.
Currently they are split into display part + SWF part. But since
the SWF part is also related to the display let's just move that
part into its own thing and flip the roles around so that the
current display part is the main function.
Ville Syrjälä [Thu, 1 Oct 2020 15:16:40 +0000 (18:16 +0300)]
drm/i915: Wait for VLV/CHV/BXT/GLK DSI panel power cycle delay on reboot
As with eDP and LVDS we should also respect the power cycle
delay on DSI panels. We are not using the power sequencer
for these, and we have no optimizations around the sleep
duration, so we just msleep() the whole thing away.
Note that the ICL+ DSI code doesn't seem to have any power
off/power cycle delay handling whatsoever. The only thing it
handles is the power on delay. As that looks pretty busted
in general I won't bother dealing with it for the time being.
Ville Syrjälä [Thu, 1 Oct 2020 15:16:39 +0000 (18:16 +0300)]
drm/i915: Wait for LVDS panel power cycle delay on reboot
Just like with eDP let's wait for the power sequencer power
cycle delay before we reboot the machine, as otherwise we
can't guarantee the panel's minimum power cycle delay will
be respected.
Ville Syrjälä [Thu, 1 Oct 2020 15:16:38 +0000 (18:16 +0300)]
drm/i915: Wait for eDP panel power cycle delay on reboot on all platforms
Extend the eDP panel power cycle delay wait on reboot handling
to cover all platforms. No reason to think that VLV/CHV are
in any way special since the documentation states that the
hardware power cycle delay goes back to its default value on
reset, and that may not be enough for all panels.
Ville Syrjälä [Thu, 1 Oct 2020 15:16:37 +0000 (18:16 +0300)]
drm/i915: Replace the VLV/CHV eDP reboot notifier with the .shutdown() hook
Currently VLV/CHV use a reboot notifier to make sure the panel
power cycle delay isn't violated across a system reboot. Replace
that with the new encoder .shutdown() hook.
And let's also stop overriding the power cycle delay with the
max value. No idea why the current code does that. The already
programmed delay should be correct.
Ville Syrjälä [Thu, 1 Oct 2020 15:16:36 +0000 (18:16 +0300)]
drm/i915: Add an encoder .shutdown() hook
Add a new encoder hook .shutdown() which will get called at the end
of the pci .shutdown() hook. We shall use this to deal with the
panel power cycle delay issues.
Ville Syrjälä [Thu, 1 Oct 2020 15:16:35 +0000 (18:16 +0300)]
drm/i915: Shut down displays gracefully on reboot
Implement the pci .shutdown() hook in order to quiesce the
hardware prior to reboot. The main purpose here is to turn
all displays off. Some displays/other drivers tend to get
confused if the state after reboot isn't exactly as they
expected.
One specific example was the Dell UP2414Q in MST mode.
It would require me to pull the power cord after a reboot
or else it would just not come back to life. Sadly I don't
have that at hand anymore so not sure if it's still
misbehaving without the graceful shutdown, or if we
managed to fix something else since I last tested it.
For good measure we do a gem suspend as well, so that
we match the suspend flow more closely. Also stopping
all DMA and whatnot is probably a good idea for kexec.
I would expect that some kind of GT reset happens on
normal reboot so probably not totally necessary there.
v2: Use the pci .shutdown() hook instead of a reboot notifier (Lukas)
Do the gem suspend for kexec (Chris)
Matt Roper [Wed, 7 Oct 2020 00:22:08 +0000 (17:22 -0700)]
drm/i915/dg1: Don't program PHY_MISC for PHY-C and PHY-D
The only bit we use in PHY_MISC is DE_IO_COMP_PWR_DOWN, and the bspec
details for that bit tell us that it need only be set for PHY-A and
PHY-B. It also turns out that there isn't even an instance of the
PHY_MISC register for PHY-D on this platform. Let's extend the EHL/RKL
logic that conditionally skips PHY_MISC usage to DG1 as well.
Lucas De Marchi [Wed, 7 Oct 2020 00:22:07 +0000 (17:22 -0700)]
drm/i915/dg1: gmbus pin mapping
Add tables to map the GMBUS pin pairs to GPIO registers and port to DDC.
From spec we have registers GPIO_CTL[1-4], so we should not do the 4->9
mapping as in ICL/TGL.
The values for VBT seem wrong in BSpec. For the current boards we
actually have a 1:1 mapping.
Lucas De Marchi [Wed, 7 Oct 2020 00:22:05 +0000 (17:22 -0700)]
drm/i915/dg1: Define MOCS table for DG1
DG1 has a new MOCS table. We still use the old definition of the table,
but as for any dgfx card it doesn't contain the control_value values
(these values don't matter as we won't program them).
Bspec: 45101
v2: Reword the comment to state that the last few entries are reserved
instead of "the last two". DG1 reserves four instead of two from
previous platforms (from Matt Roper)
Matt Roper [Wed, 7 Oct 2020 00:22:04 +0000 (17:22 -0700)]
drm/i915/dg1: Initialize RAWCLK properly
DG1 always uses a 38.4 MHz rawclk rather than the 19.2/24 MHz
frequencies on CNP+. Note that register bits associated with this
frequency confusingly use 37 for the divider field rather than 38 as you
might expect.
For simplicity, let's just assume that this 38.4 MHz frequency will hold
true for other future platforms with "fake" PCH south displays and that
the CNP-style behavior will remain for other platforms with a real PCH.
Bspec: 49950
Bspec: 49309 Cc: Aditya Swarup <aditya.swarup@intel.com> Cc: Clinton Taylor <Clinton.A.Taylor@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201007002210.3678024-2-lucas.demarchi@intel.com
projects / kernel.git / log