John W Linville [Fri, 21 Jul 2017 18:12:24 +0000 (14:12 -0400)]
igb: support BCM54616 PHY
The management port on an Edgecore AS7712-32 switch uses an igb MAC, but
it uses a BCM54616 PHY. Without a patch like this, loading the igb
module produces dmesg output like this:
[ 3.439125] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.439866] igb: probe of 0000:00:14.0 failed with error -2
Signed-off-by: John W Linville <linville@tuxdriver.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver assumes the VF will not send another mailbox message until
the PF has written its reply to the previous message. If the VF does,
that message will be silently dropped by the PF before it writes its
reply to the mailbox. This results in a VF mailbox timeout for posted
messages waiting for an ACK, and the VF is reset by the
igbvf_watchdog_task in the VM.
Add a lock around the VF mailbox ops to prevent the VF from sending
another message while the PF is still processing the previous one.
Signed-off-by: Greg Edwards <gedwards@ddn.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i219 (8) and i219 (9) are the next LOM generations that will be available
on the next Intel Client platform (IceLake).
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Raanan Avargil <raanan.avargil@intel.com> Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Greg Edwards [Wed, 28 Jun 2017 15:22:26 +0000 (09:22 -0600)]
igb: do not drop PF mailbox lock after read of VF message
When the PF receives a mailbox message from the VF, it grabs the mailbox
lock, reads the VF message from the mailbox, ACKs the message and drops
the lock.
While the PF is performing the action for the VF message, nothing
prevents another VF message from being posted to the mailbox. The
current code handles this condition by just dropping any new VF messages
without processing them. This results in a mailbox timeout in the VM
for posted messages waiting for an ACK, and the VF is reset by the
igbvf_watchdog_task in the VM.
Given the right sequence of VF messages and mailbox timeouts, this
condition can go on ad infinitum.
Modify the PF mailbox read method to take an 'unlock' argument that
optionally leaves the mailbox locked by the PF after reading the VF
message. This ensures another VF message is not posted to the mailbox
until after the PF has completed processing the VF message and written
its reply.
Signed-off-by: Greg Edwards <gedwards@ddn.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TSAUXC.DisableSystime is never set, so SYSTIM runs into a SYS WRAP
every 1100 secs on 80580/i350/i354 (40 bit SYSTIM) and every 35000
secs on 80576 (45 bit SYSTIM).
This wrap event sets the TSICR.SysWrap bit unconditionally.
However, checking TSIM at interrupt time shows that this event does not
actually cause the interrupt. Rather, it's just bycatch while the
actual interrupt is caused by, for instance, TSICR.TXTS.
The conclusion is that the SYS WRAP is actually expected, so the
"unexpected SYS WRAP" message is entirely bogus and just helps to
confuse users. Drop it.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Acked-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check return value from call to e1e_wphy(). This value is being
checked during previous calls to function e1e_wphy() and it seems
a check was missing here.
Addresses-Coverity-ID: 1226905 Signed-off-by: Gustavo A R Silva <garsilva@embeddedor.com> Reviewed-by: Ethan Zhao <ethan.zhao@oracle.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cliff Spradlin [Mon, 19 Jun 2017 20:30:43 +0000 (13:30 -0700)]
igb: protect TX timestamping from API misuse
HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the igb
driver still allowed TX packets to request HW timestamping. In this
situation, the _IGB_PTP_TX_IN_PROGRESS flag was set and would never
clear. This prevented any future HW timestamping requests to succeed.
Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.
Signed-off-by: Cliff Spradlin <cspradlin@google.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Gangfeng Huang [Sat, 27 May 2017 01:17:53 +0000 (09:17 +0800)]
igb: Fix error of RX network flow classification
After add an ethertype filter, if user change the adapter speed several
times, the error "ethtool -N: etype filters are all used" is reported by
igb driver.
In older patch, function igb_nfc_filter_exit() and igb_nfc_filter_restore()
is not paried. igb_nfc_filter_restore() exist in igb_up(), but function
igb_nfc_filter_exit() is exist in __igb_close(). In the process of speed
changing, only igb_nfc_filter_restore() is called, it will take a position
of ethertype bitmap.
Reproduce steps:
Step 1: Add a etype filter by ethtool
$ethtool -N eth0 flow-type ether proto 0x88F8 action 1
Step 2: Change the adapter speed to 100M/full duplex
$ethtool -s eth0 speed 100 duplex full
Step 3: Change the adapter speed to 1000M/full duplex
ethtool -s eth0 speed 1000 duplex full
Repeat step2 and step3, then dmesg the system log, you can find the error
message, add new ethtype filter is also failed.
This fixing is move igb_nfc_filter_exit() from __igb_close() to igb_down()
to make igb_nfc_filter_restore()/igb_nfc_filter_exit() is paired.
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David Ahern [Mon, 7 Aug 2017 17:08:10 +0000 (10:08 -0700)]
net: vrf: Add extack messages for newlink failures
Add extack error messages for failure paths creating vrf devices. Once
extack support is added to iproute2, we go from the unhelpful:
$ ip li add foobar type vrf
RTNETLINK answers: Invalid argument
to:
$ ip li add foobar type vrf
Error: VRF table id is missing
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Update DSA's FDB API and perform switchdev cleanup
The patchset adds support for configuring static FDB entries via the
switchdev notification chain. The current method for FDB configuration
uses the switchdev's bridge bypass implementation. In order to support
this legacy way and to perform the switchdev cleanup, the implementation
is moved inside DSA.
The DSA drivers cannot sync the software bridge with hardware learned
entries and use the switchdev's implementation of bypass FDB dumping.
Because they are the only ones using this functionality, the fdb_dump
implementation is moved from switchdev code into DSA.
Finally after this changes a major cleanup in switchdev can be done.
Please see individual patches for patch specific change logs.
v1->v2
- Split MDB/vlan dump removal into core/driver removal.
v2->v3
- The self implementation for FDB add/del is moved inside DSA.
====================
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: switchdev: Remove bridge bypass support from switchdev
Currently the bridge port flags, vlans, FDBs and MDBs can be offloaded
through the bridge code, making the switchdev's SELF bridge bypass
implementation to be redundant. This implies several changes:
- No need for dump infra in switchdev, DSA's special case is handled
privately.
- Remove obj_dump from switchdev_ops.
- FDBs are removed from obj_add/del routines, due to the fact that they
are offloaded through the bridge notification chain.
- The switchdev_port_bridge_xx() and switchdev_port_fdb_xx() functions
can be removed.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: Remove FDB deletion through switchdev object
At this point no driver supports FDB add/del through switchdev object
but rather via notification chain, thus, it is removed.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the MDB HW database is synced with the bridge's one, thus,
There is no need to support special dump functionality.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Remove support for MDB dump from DSA's drivers
This is done as a preparation before removing support for MDB dump from
DSA core. The MDBs are synced with the bridge and thus there is no
need for special dump operation support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Remove support for bypass bridge port attributes/vlan set
The bridge port attributes/vlan for DSA devices should be set only
from bridge code. Furthermore, The vlans are synced totally with the
bridge so there is no need for special dump support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Remove support for vlan dump from DSA's drivers
This is done as a preparation before removing support for vlan dump from
DSA core. The vlans are synced with the bridge and thus there is no
need for special dump operation support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Add support for querying supported bridge flags
The DSA drivers do not support bridge flags offload. Yet, this attribute
should be added in order for the bridge to fail when one tries set a
flag on the port, as explained in commit dc0ecabd6231 ("net: switchdev:
Add support for querying supported bridge flags by hardware").
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA uses switchdev's implementation of FDB add/del ndos. This
patch moves the implementation inside DSA in order to support the legacy
way for static FDB configuration.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Add support for learning FDB through notification
Add support for learning FDB through notification. The driver defers
the hardware update via ordered work queue. In case of a successful
FDB add a notification is sent back to bridge.
In case of hw FDB del failure the static FDB will be deleted from
the bridge, thus, the interface is moved to down state in order to
indicate inconsistent situation.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Remove switchdev dependency from DSA switch notifier chain
Currently, the switchdev objects are embedded inside the DSA notifier
info. This patch removes this dependency. This is done as a preparation
stage before adding support for learning FDB through the switchdev
notification chain.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Change DSA slave FDB API to be switchdev independent
In order to support FDB add/del to be on a notifier chain the slave
API need to be changed to be switchdev independent.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com> Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bhumika Goyal [Sun, 6 Aug 2017 08:51:45 +0000 (14:21 +0530)]
hamradio: baycom: make hdlcdrv_ops const
Make hdlcdrv_ops structures const as they are only passed to
hdlcdrv_register function. The corresponding argument is of type const,
so make the structures const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Ilan Tayari:
1. Set up a host-to-host IPSec tunnel (or transport, doesn't matter)
2. Ping over IPSec, or do something to populate the pcpu cache
3. Join a MC group, then leave MC group
4. Try to ping again using same CPU as before -> traffic
doesn't egress the machine at all
Ilan debugged the problem down to the fact that one of the path dsts
devices point to lo due to earlier dst_dev_put().
In this case, dst is marked as DEAD and we cannot reuse the bundle.
The cache only asserted that the requested policy and that of the cached
bundle match, but its not enough - also verify the path is still valid.
Fixes: ec30d78c14a813 ("xfrm: add xdst pcpu cache") Reported-by: Ayham Masood <ayhamm@mellanox.com> Tested-by: Ilan Tayari <ilant@mellanox.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Several DSA core setup functions take many arguments, mostly because of
the legacy code. This patch series removes the useless args of these
functions, where either the dsa_switch or dsa_port argument is enough.
Changes in v2:
- ds->dev is already assigned by dsa_switch_alloc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 5 Aug 2017 20:20:19 +0000 (16:20 -0400)]
net: dsa: remove useless args of dsa_slave_create
dsa_slave_create currently takes 4 arguments while it only needs the
related dsa_port and its name. Remove all other arguments.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 5 Aug 2017 20:20:18 +0000 (16:20 -0400)]
net: dsa: remove useless args of dsa_cpu_dsa_setup
dsa_cpu_dsa_setup currently takes 4 arguments but they are all available
from the dsa_port argument. Remove all others.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 5 Aug 2017 20:20:17 +0000 (16:20 -0400)]
net: dsa: remove useless argument in legacy setup
dsa_switch_alloc() already assigns ds-dev, which can be used in
dsa_switch_setup_one and dsa_cpu_dsa_setups instead of requiring an
additional struct device argument.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It changes the lan9303_enable_packet_processing,
lan9303_disable_packet_processing() to pass port number (0,1,2) as
parameter instead of port offset. This aligns them with
other functions in the module, and makes it possible to simplify the code.
The lan9303_enable_packet_processing, lan9303_disable_packet_processing
functions operate on port. Therefore rename the functions to reflect that
as well.
Reviewer pointed out lan9303_get_ethtool_stats would be better off with
the use of a lan9303_read_switch_port(). So that was added to the series.
Changes v1 -> v2:
- introduced lan9303_write_switch_port() in first patch
- inserted LAN9303_NUM_PORTS patch
- Use LAN9303_NUM_PORTS in last patch. Plus whitespace change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In lan9303_get_ethtool_stats: Get rid of 0x400 constant magic
by using new lan9303_read_switch_reg() inside loop.
Reduced scope of two variables.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The lan9303_enable_packet_processing, lan9303_disable_packet_processing
functions operate on port, so the names should reflect that.
And to align with lan9303_disable_processing(), rename:
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify usage of lan9303_enable_packet_processing,
lan9303_disable_packet_processing()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland [Sat, 5 Aug 2017 11:05:47 +0000 (13:05 +0200)]
net: dsa: lan9303: define LAN9303_NUM_PORTS 3
Will be used instead of '3' in upcomming patches.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland [Sat, 5 Aug 2017 11:05:46 +0000 (13:05 +0200)]
net: dsa: lan9303: Change lan9303_xxx_packet_processing() port param.
lan9303_enable_packet_processing, lan9303_disable_packet_processing()
Pass port number (0,1,2) as parameter instead of port offset.
Because other functions in the module pass port numbers.
And to enable simplifications in following patch.
Introduce lan9303_write_switch_port().
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
ipv6: sr: add support for advanced local segment processing
v2: use EXPORT_SYMBOL_GPL
The current implementation of IPv6 SR supports SRH insertion/encapsulation
and basic segment endpoint behavior (i.e., processing of an SRH contained in
a packet whose active segment (IPv6 DA) is routed to the local node). This
behavior simply consists of updating the DA to the next segment and forwarding
the packet accordingly. This processing is realised for all such packets,
regardless of the active segment.
The most recent specifications of IPv6 SR [1] [2] extend the SRH processing
features as follows. Each segment endpoint defines a MyLocalSID table.
This table maps segments to operations to perform. For each ingress IPv6
packet whose DA is part of a given prefix, the segment endpoint looks
up the active segment (i.e., the IPv6 DA) in the MyLocalSID table and
applies the corresponding operation. Such specifications enable to specify
arbitrary operations besides the basic SRH processing and allow for a more
fine-grained classification.
This patch series implements those extended specifications by leveraging
a new type of lightweight tunnel, seg6local. The MyLocalSID table is
simply an arbitrary routing table (using CONFIG_IPV6_MULTIPLE_TABLES). The
following commands would assign the prefix fc00::/64 to the MyLocalSID
table, map the segment fc00::42 to the regular SRH processing function
(named "End"), and drop all packets received with an undefined active
segment:
ip -6 rule add fc00::/64 lookup 100
ip -6 route add fc00::42 encap seg6local action End dev eth0 table 100
ip -6 route add blackhole default table 100
As another example, the following command would assign the segment
fc00::1234 to the regular SRH processing function, except that the
processed packet must be forwarded to the next-hop fc42::1 (this operation
is named "End.X"):
ip -6 route add fc00::1234 encap seg6local action End.X nh6 fc42::1 dev eth0 table 100
Those two basic operations (End and End.X) are defined in [1]. A more
extensive list of advanced operations is defined in [2].
The first two patches of the series are preliminary work that remove an
assumption about initial SRH format, and export the two functions used to
insert and encapsulate an SRH onto packets. The third patch defines the
new seg6local lightweight tunnel and implement the core functions. The
fourth patch implements the operations needed to handle the newly defined
rtnetlink attributes. The fifth patch implements a few SRH processing
operations, including End and End.X.
David Lebrun [Sat, 5 Aug 2017 10:38:27 +0000 (12:38 +0200)]
ipv6: sr: add rtnetlink functions for seg6local action parameters
This patch adds the necessary functions to parse, fill, and compare
seg6local rtnetlink attributes, for all defined action parameters.
- The SRH parameter defines an SRH to be inserted or encapsulated.
- The TABLE parameter defines the table to use for the route lookup of
the next segment or the inner decapsulated packet.
- The NH4 parameter defines the IPv4 next-hop for an inner decapsulated
IPv4 packet.
- The NH6 parameter defines the IPv6 next-hop for the next segment or
for an inner decapsulated IPv6 packet
- The IIF parameter defines an ingress interface index.
- The OIF parameter defines an egress interface index.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net>
David Lebrun [Sat, 5 Aug 2017 10:38:26 +0000 (12:38 +0200)]
ipv6: sr: define core operations for seg6local lightweight tunnel
This patch implements a new type of lightweight tunnel named seg6local.
A seg6local lwt is defined by a type of action and a set of parameters.
The action represents the operation to perform on the packets matching the
lwt's route, and is not necessarily an encapsulation. The set of parameters
are arguments for the processing function.
Each action is defined in a struct seg6_action_desc within
seg6_action_table[]. This structure contains the action, mandatory
attributes, the processing function, and a static headroom size required by
the action. The mandatory attributes are encoded as a bitmask field. The
static headroom is set to a non-zero value when the processing function
always add a constant number of bytes to the skb (e.g. the header size for
encapsulations).
To facilitate rtnetlink-related operations such as parsing, fill_encap,
and cmp_encap, each type of action parameter is associated to three
function pointers, in seg6_action_params[].
All actions defined in seg6_local.h are detailed in [1].
David Lebrun [Sat, 5 Aug 2017 10:38:25 +0000 (12:38 +0200)]
ipv6: sr: export SRH insertion functions
This patch exports the seg6_do_srh_encap() and seg6_do_srh_inline()
functions. It also removes the CONFIG_IPV6_SEG6_INLINE knob
that enabled the compilation of seg6_do_srh_inline(). This function
is now built-in.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net>
David Lebrun [Sat, 5 Aug 2017 10:38:24 +0000 (12:38 +0200)]
ipv6: sr: allow SRH insertion with arbitrary segments_left value
The seg6_validate_srh() function only allows SRHs whose active segment is
the first segment of the path. However, an application may insert an SRH
whose active segment is not the first one. Such an application might be
for example an SR-aware Virtual Network Function.
This patch enables to insert SRHs with an arbitrary active segment.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Sat, 5 Aug 2017 05:02:19 +0000 (22:02 -0700)]
bpf: devmap fix mutex in rcu critical section
Originally we used a mutex to protect concurrent devmap update
and delete operations from racing with netdev unregister notifier
callbacks.
The notifier hook is needed because we increment the netdev ref
count when a dev is added to the devmap. This ensures the netdev
reference is valid in the datapath. However, we don't want to block
unregister events, hence the initial mutex and notifier handler.
The concern was in the notifier hook we search the map for dev
entries that hold a refcnt on the net device being torn down. But,
in order to do this we require two steps,
(i) dereference the netdev: dev = rcu_dereference(map[i])
(ii) test ifindex: dev->ifindex == removing_ifindex
and then finally we can swap in the NULL dev in the map via an
xchg operation,
xchg(map[i], NULL)
The danger here is a concurrent update could run a different
xchg op concurrently leading us to replace the new dev with a
NULL dev incorrectly.
CPU 1 CPU 2
notifier hook bpf devmap update
dev = rcu_dereference(map[i])
dev = rcu_dereference(map[i])
xchg(map[i]), new_dev);
rcu_call(dev,...)
xchg(map[i], NULL)
The above flow would create the incorrect state with the dev
reference in the update path being lost. To resolve this the
original code used a mutex around the above block. However,
updates, deletes, and lookups occur inside rcu critical sections
so we can't use a mutex in this context safely.
Fortunately, by writing slightly better code we can avoid the
mutex altogether. If CPU 1 in the above example uses a cmpxchg
and _only_ replaces the dev reference in the map when it is in
fact the expected dev the race is removed completely. The two
cases being illustrated here, first the race condition,
CPU 1 CPU 2
notifier hook bpf devmap update
dev = rcu_dereference(map[i])
dev = rcu_dereference(map[i])
xchg(map[i]), new_dev);
rcu_call(dev,...)
odev = cmpxchg(map[i], dev, NULL)
Now we can test the cmpxchg return value, detect odev != dev and
abort. Or in the good case,
And viola the original race we tried to solve with a mutex is
corrected and the trace noted by Sasha below is resolved due
to removal of the mutex.
Note: When walking the devmap and removing dev references as needed
we depend on the core to fail any calls to dev_get_by_index() using
the ifindex of the device being removed. This way we do not race with
the user while searching the devmap.
Additionally, the mutex was also protecting list add/del/read on
the list of maps in-use. This patch converts this to an RCU list
and spinlock implementation. This protects the list from concurrent
alloc/free operations. The notifier hook walks this list so it uses
RCU read semantics.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 16315, name: syz-executor1
1 lock held by syz-executor1/16315:
#0: (rcu_read_lock){......}, at: [<ffffffff8c363bc2>] map_delete_elem kernel/bpf/syscall.c:577 [inline]
#0: (rcu_read_lock){......}, at: [<ffffffff8c363bc2>] SYSC_bpf kernel/bpf/syscall.c:1427 [inline]
#0: (rcu_read_lock){......}, at: [<ffffffff8c363bc2>] SyS_bpf+0x1d32/0x4ba0 kernel/bpf/syscall.c:1388
Fixes: 2ddf71e23cc2 ("net: add notifier hooks for devmap bpf map") Reported-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 7 Aug 2017 21:12:18 +0000 (14:12 -0700)]
Merge branch 'net_sched-clean-up-filter-handle'
Cong Wang says:
====================
net_sched: clean up filter handle
This patchset sits in my local branch for a long time, it is time to
send it out. It cleans up the ambiguous use of 'unsigned long fh',
please see each of them for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sat, 5 Aug 2017 04:31:43 +0000 (21:31 -0700)]
net_sched: use void pointer for filter handle
Now we use 'unsigned long fh' as a pointer in every place,
it is safe to convert it to a void pointer now. This gets
rid of many casts to pointer.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sat, 5 Aug 2017 04:31:42 +0000 (21:31 -0700)]
net_sched: refactor notification code for RTM_DELTFILTER
It is confusing to use 'unsigned long fh' as both a handle
and a pointer, especially commit 9ee7837449b3
("net sched filters: fix notification of filter delete with proper handle").
This patch introduces tfilter_del_notify() so that we can
pass it as a pointer as before, and we don't need to check
RTM_DELTFILTER in tcf_fill_node() any more.
This prepares for the next patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
bpf: add support for sys_{enter|exit}_* tracepoints
Currently, bpf programs cannot be attached to sys_enter_* and sys_exit_*
style tracepoints. The main reason is that syscalls/sys_enter_* and syscalls/sys_exit_*
tracepoints are treated differently from other tracepoints and there
is no bpf hook to it.
This patch set adds bpf support for these syscalls tracepoints and also
adds a test case for it.
Changelogs:
v3 -> v4:
- Check the legality of ctx offset access for syscall tracepoint as well.
trace_event_get_offsets will return correct max offset for each
specific syscall tracepoint.
- Use variable length array to avoid hardcode 6 as the maximum
arguments beyond syscall_nr.
v2 -> v3:
- Fix a build issue
v1 -> v2:
- Do not use TRACE_EVENT_FL_CAP_ANY to identify syscall tracepoint.
Instead use trace_event_call->class.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Fri, 4 Aug 2017 23:00:09 +0000 (16:00 -0700)]
bpf: add support for sys_enter_* and sys_exit_* tracepoints
Currently, bpf programs cannot be attached to sys_enter_* and sys_exit_*
style tracepoints. The iovisor/bcc issue #748
(https://github.com/iovisor/bcc/issues/748) documents this issue.
For example, if you try to attach a bpf program to tracepoints
syscalls/sys_enter_newfstat, you will get the following error:
# ./tools/trace.py t:syscalls:sys_enter_newfstat
Ioctl(PERF_EVENT_IOC_SET_BPF): Invalid argument
Failed to attach BPF to tracepoint
The main reason is that syscalls/sys_enter_* and syscalls/sys_exit_*
tracepoints are treated differently from other tracepoints and there
is no bpf hook to it.
This patch adds bpf support for these syscalls tracepoints by
. permitting bpf attachment in ioctl PERF_EVENT_IOC_SET_BPF
. calling bpf programs in perf_syscall_enter and perf_syscall_exit
The legality of bpf program ctx access is also checked.
Function trace_event_get_offsets returns correct max offset for each
specific syscall tracepoint, which is compared against the maximum offset
access in bpf program.
Signed-off-by: Yonghong Song <yhs@fb.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Fri, 4 Aug 2017 21:43:43 +0000 (00:43 +0300)]
of_mdio: use of_property_read_u32_array()
The "fixed-link" prop support predated of_property_read_u32_array(), so
basically had to open-code it. Using the modern API saves 24 bytes of the
object code (ARM gcc 4.8.5); the only behavior change would be that the
prop length check is now less strict (however the strict pre-check done
in of_phy_is_fixed_link() is left intact anyway)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
John Allen [Mon, 7 Aug 2017 20:42:30 +0000 (15:42 -0500)]
ibmvnic: Report rx buffer return codes as netdev_dbg
Reporting any return code for a receive buffer as an "rx error" only
produces alarming noise and the only values that have been observed to be
used in this field are not error conditions. Change this to a netdev_dbg
with a more descriptive message.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: l3mdev: Support for sockets bound to enslaved device
A missing piece to the VRF puzzle is the ability to bind sockets to
devices enslaved to a VRF. This patch set adds the enslaved device
index, sdif, to IPv4 and IPv6 socket lookups. The end result for users
is the following scope options for services:
1. "global" services - sockets not bound to any device
Allows 1 service to work across all network interfaces with
connected sockets bound to the VRF the connection originates
(Requires net.ipv4.tcp_l3mdev_accept=1 for TCP and
net.ipv4.udp_l3mdev_accept=1 for UDP)
2. "VRF" local services - sockets bound to a VRF
Sockets work across all network interfaces enslaved to a VRF but
are limited to just the one VRF.
3. "device" services - sockets bound to a specific network interface
Service works only through the one specific interface.
v3
- convert __inet_lookup_established in dccp_v4_err; missed in v2
v2
- remove sk_lookup struct and add sdif as an argument to existing
functions
Changes since RFC:
- no significant logic changes; mainly whitespace cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 7 Aug 2017 15:44:22 +0000 (08:44 -0700)]
net: ipv6: add second dif to raw socket lookups
Add a second device index, sdif, to raw socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 7 Aug 2017 15:44:21 +0000 (08:44 -0700)]
net: ipv6: add second dif to inet6 socket lookups
Add a second device index, sdif, to inet6 socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
TCP moves the data in the cb. Prior to tcp_v4_rcv (e.g., early demux) the
ingress index is obtained from IPCB using inet_sdif and after tcp_v4_rcv
tcp_v4_sdif is used.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 7 Aug 2017 15:44:20 +0000 (08:44 -0700)]
net: ipv6: add second dif to udp socket lookups
Add a second device index, sdif, to udp socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Early demux lookups are handled in the next patch as part of INET_MATCH
changes.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 7 Aug 2017 15:44:18 +0000 (08:44 -0700)]
net: ipv4: add second dif to raw socket lookups
Add a second device index, sdif, to raw socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 7 Aug 2017 15:44:17 +0000 (08:44 -0700)]
net: ipv4: add second dif to inet socket lookups
Add a second device index, sdif, to inet socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
TCP moves the data in the cb. Prior to tcp_v4_rcv (e.g., early demux) the
ingress index is obtained from IPCB using inet_sdif and after the cb move
in tcp_v4_rcv the tcp_v4_sdif helper is used.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 7 Aug 2017 15:44:16 +0000 (08:44 -0700)]
net: ipv4: add second dif to udp socket lookups
Add a second device index, sdif, to udp socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Early demux lookups are handled in the next patch as part of INET_MATCH
changes.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 7 Aug 2017 18:34:41 +0000 (11:34 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
The first wireless-drivers-next pull request for 4.14. I'm submitting
this unusally late in the cycle as my vacation postponed this. But
even if this is late there's not still that much new features, mostly
cleanup or fixes.
Major changes:
ath10k
* preparation for wcn3990 support
iwlwifi
* Reorganization of the code into separate directories continues
qtnfmac
* regulatory support updates
* add get_channel, dump_survey and channel_switch cfg80211 handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Mon, 7 Aug 2017 10:41:53 +0000 (12:41 +0200)]
hns3: fix unused function warning
Without CONFIG_PCI_IOV, we get a harmless warning about an
unused function:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2273:13: error: 'hclge_disable_sriov' defined but not used [-Werror=unused-function]
The #ifdefs in this driver are obviously wrong, so this just
removes them and uses an IS_ENABLED() check that does the same
thing correctly in a more readable way.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 7 Aug 2017 17:42:09 +0000 (10:42 -0700)]
Merge tag 'mlx5-shared-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-shared-2017-08-07
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: sched: summer cleanup part 2, ndo_setup_tc
This patchset focuses on ndo_setup_tc and its args.
Currently there are couple of things that do not make much sense.
The type is passed in struct tc_to_netdev, but as it is always
required, should be arg of the ndo. Other things are passed as args
but they are only relevant for cls offloads and not mqprio. Therefore,
they should be pushed to struct. As the tc_to_netdev struct in the end
is just a container of single pointer, we get rid of it and pass the
struct according to type. So in the end, we have:
ndo_setup_tc(dev, type, type_data_struct)
There are couple of cosmetics done on the way to make things smooth.
Also, reported error is consolidated to eopnotsupp in case the
asked offload is not supported.
Jiri Pirko [Mon, 7 Aug 2017 08:15:32 +0000 (10:15 +0200)]
net: sched: get rid of struct tc_to_netdev
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Mon, 7 Aug 2017 08:15:30 +0000 (10:15 +0200)]
net: sched: move prio into cls_common
prio is not cls_flower specific, but it is meaningful for all
classifiers. Seems that only mlxsw cares about the value. Obviously,
cls offload in other drivers is broken.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Mon, 7 Aug 2017 08:15:29 +0000 (10:15 +0200)]
net: sched: push cls related args into cls_common structure
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Mon, 7 Aug 2017 08:15:26 +0000 (10:15 +0200)]
dsa: push cls_matchall setup_tc processing into a separate function
Let dsa_slave_setup_tc be a splitter for specific setup_tc types and
push out cls_matchall specific code into a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Mon, 7 Aug 2017 08:15:23 +0000 (10:15 +0200)]
mlx5e_rep: push cls_flower setup_tc processing into a separate function
Let mlx5e_rep_setup_tc (former mlx5e_rep_ndo_setup_tc) be a splitter for
specific setup_tc types and push out cls_flower specific code into
a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Mon, 7 Aug 2017 08:15:22 +0000 (10:15 +0200)]
mlx5e: push cls_flower and mqprio setup_tc processing into separate functions
Let mlx5e_setup_tc (former mlx5e_ndo_setup_tc) be a splitter for specific
setup_tc types and push out cls_flower and mqprio specific codes into
separate functions. Also change the return values so they are the same
as in the rest of the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Mon, 7 Aug 2017 08:15:21 +0000 (10:15 +0200)]
ixgbe: push cls_u32 and mqprio setup_tc processing into separate functions
Let __ixgbe_setup_tc be a splitter for specific setup_tc types and push out
cls_u32 and mqprio specific codes into separate functions. Also change
the return values so they are the same as in the rest of the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Increase the maximum flow counters supported
Read new NIC capability field which represnts 16 MSBs of the max flow
counters number supported (max_flow_counter_31_16).
Backward compatibility with older firmware is preserved, the modified
driver reads max_flow_counter_31_16 as 0 from the older firmware and
uses up to 64K counters.
Changed flow counter id from 16 bits to 32 bits. Backward compatibility
with older firmware is preserved as we kept the 16 LSBs of the counter
id in place and added 16 MSBs from reserved field.
Changed the background bulk reading of flow counters to work in chunks
of at most 32K counters, to make sure we don't attempt to allocate very
large buffers.
Erez Shitrit [Wed, 7 Jun 2017 09:14:24 +0000 (12:14 +0300)]
net/mlx5: Delay events till ib registration ends
When mlx5_ib registers itself to mlx5_core as an interface, it will
call mlx5_add_device which will call mlx5_ib interface add callback,
in case the latter successfully returns, only then mlx5_core will add
it to the interface list and async events will be forwarded to mlx5_ib.
Between mlx5_ib interface add callback and mlx5_core adding the mlx5_ib
interface to its devices list, arriving mlx5_core events can be missed
by the new mlx5_ib registering interface.
In other words:
thread 1: mlx5_ib: mlx5_register_interface(dev)
thread 1: mlx5_core: mlx5_add_device(dev)
thread 1: mlx5_core: ctx = dev->add => (mlx5_ib)->mlx5_ib_add
thread 2: mlx5_core_event: **new event arrives, forward to dev_list
thread 1: mlx5_core: add_ctx_to_dev_list(ctx)
/* previous event was missed by the new interface.*/
It is ok to miss events before dev->add (mlx5_ib)->mlx5_ib_add_device
but not after.
We fix this race by accumulating the events that come between the
ib_register_device (inside mlx5_add_device->(dev->add)) till the adding
to the list completes and fire them to the new registering interface
after that.
Fixes: f1ee87fe55c8 ("net/mlx5: Organize device list API in one place") Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Mon, 5 Jun 2017 12:17:12 +0000 (15:17 +0300)]
net/mlx5: Add CONFIG_MLX5_ESWITCH Kconfig
Allow to selectively build the driver with or without sriov eswitch, VF
representors and TC offloads.
Also remove the need of two ndo ops structures (sriov & basic)
and keep only one unified ndo ops, compile out VF SRIOV ndos when not
needed (MLX5_ESWITCH=n), and for VF netdev calling those ndos will result
in returning -EPERM.
Saeed Mahameed [Sun, 4 Jun 2017 20:11:55 +0000 (23:11 +0300)]
net/mlx5: Separate between E-Switch and MPFS
Multi-Physical Function Switch (MPFs) is required for when multi-PF
configuration is enabled to allow passing user configured unicast MAC
addresses to the requesting PF.
Before this patch eswitch.c used to manage the HW MPFS l2 table,
E-Switch always (regardless of sriov) enabled vport(0) (NIC PF) vport's
contexts update on unicast mac address list changes, to populate the PF's
MPFS L2 table accordingly.
In downstream patch we would like to allow compiling the driver without
E-Switch functionalities, for that we move MPFS l2 table logic out
of eswitch.c into its own file, and provide Kconfig flag (MLX5_MPFS) to
allow compiling out MPFS for those who don't want Multi-PF support.
NIC PF netdevice will now directly update MPFS l2 table via the new MPFS
API. VF netdevice has no access to MPFS L2 table, so E-Switch will remain
responsible of updating its MPFS l2 table on behalf of its VFs.
Due to this change we also don't require enabling vport(0) (PF vport)
unicast mac changes events anymore, for when SRIOV is not enabled.
Which means E-Switch is now activated only on SRIOV activation, and not
required otherwise.
Saeed Mahameed [Tue, 6 Jun 2017 06:12:04 +0000 (09:12 +0300)]
net/mlx5e: NIC netdev init flow cleanup
Remove redundant call to unregister vport representor in mlx5e_add error
flow.
Hide the representor priv and eswitch internal structures from en_main.c
as preparation step for downstream patches which would allow building
the driver without support for representors and eswitch.
Fixes: 6f08a22c5fb2 ("net/mlx5e: Register/unregister vport representors on interface attach/detach") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Saeed Mahameed [Tue, 6 Jun 2017 14:46:49 +0000 (17:46 +0300)]
net/mlx5e: Rearrange netdevice ops structures
Since we are going to allow building the driver without eswitch support,
it would be possible to compile out the sriov netdevice ops struct such
that the basic ops instance will be used for non VF devices too.
Add missing udp tunnel ndos into mlx5e_netdev_ops_basic.
While here, rearrange some ndos in the sriov ops struct and put
vf/eswitch related ndos towards the end of it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Xin Long [Sat, 5 Aug 2017 12:00:04 +0000 (20:00 +0800)]
sctp: remove the typedef sctp_subtype_t
This patch is to remove the typedef sctp_subtype_t, and
replace with union sctp_subtype in the places where it's
using this typedef.
Note that it doesn't fix many indents although it should,
as sctp_disposition_t's removal would mess them up again.
So better to fix them when removing sctp_disposition_t in
later patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log