Like the Acer Switch One 10 S1003, for which there already is a quirk,
the Acer Switch V 10 (SW5-017) has a 800x1280 portrait screen mounted
in the tablet part of a landscape oriented 2-in-1. Add a quirk for this.
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
When trying to transmit an data frame with tx_status to a destination
that have no route in the mesh, then it is dropped without recrediting
the ack_status_frames idr.
Once it is exhausted, wpa_supplicant starts failing to do SAE with
NL80211_CMD_FRAME and logs "nl80211: Frame command failed".
Use ieee80211_free_txskb() instead of kfree_skb() to fix it.
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. The UBSAN warning calltrace like below:
UBSAN: shift-out-of-bounds in kernel/auditfilter.c:179:23
left shift of 1 by 31 places cannot be represented in type 'int'
Call Trace:
<TASK>
dump_stack_lvl+0x7d/0xa5
dump_stack+0x15/0x1b
ubsan_epilogue+0xe/0x4e
__ubsan_handle_shift_out_of_bounds+0x1e7/0x20c
audit_register_class+0x9d/0x137
audit_classes_init+0x4d/0xb8
do_one_initcall+0x76/0x430
kernel_init_freeable+0x3b3/0x422
kernel_init+0x24/0x1e0
ret_from_fork+0x1f/0x30
</TASK>
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
[PM: remove bad 'Fixes' tag as issue predates git, added in v2.6.6-rc1] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes a warning that occurs when rc table support is enabled
(IEEE80211_HW_SUPPORTS_RC_TABLE) in mac80211_hwsim and the PS mode
is changed via the exported debugfs attribute.
When the PS mode is changed, a packet is broadcasted via
hwsim_send_nullfunc by creating and transmitting a plain skb with only
header initialized. The ieee80211 rate array in the control buffer is
zero-initialized. When ratetbl support is enabled, ieee80211_get_tx_rates
is called for the skb with sta parameter set to NULL and thus no
ratetbl can be used. The final rate array then looks like
[-1,0; 0,0; 0,0; 0,0] which causes the warning in ieee80211_get_tx_rate.
The issue is fixed by setting the count of the first rate with idx '0'
to 1 and hence ieee80211_get_tx_rates won't overwrite it with idx '-1'.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernel iterates over ATTR_RECORDs in mft record in ntfs_attr_find().
Because the ATTR_RECORDs are next to each other, kernel can get the next
ATTR_RECORD from end address of current ATTR_RECORD, through current
ATTR_RECORD length field.
The problem is that during iteration, when kernel calculates the end
address of current ATTR_RECORD, kernel may trigger an integer overflow bug
in executing `a = (ATTR_RECORD*)((u8*)a + le32_to_cpu(a->length))`. This
may wrap, leading to a forever iteration on 32bit systems.
This patch solves it by adding some checks on calculating end address
of current ATTR_RECORD during iteration.
Kernel iterates over ATTR_RECORDs in mft record in ntfs_attr_find(). To
ensure access on these ATTR_RECORDs are within bounds, kernel will do some
checking during iteration.
The problem is that during checking whether ATTR_RECORD's name is within
bounds, kernel will dereferences the ATTR_RECORD name_offset field, before
checking this ATTR_RECORD strcture is within bounds. This problem may
result out-of-bounds read in ntfs_attr_find(), reported by Syzkaller:
==================================================================
BUG: KASAN: use-after-free in ntfs_attr_find+0xc02/0xce0 fs/ntfs/attrib.c:597
Read of size 2 at addr ffff88807e352009 by task syz-executor153/3607
This patch solves it by moving the ATTR_RECORD strcture's bounds checking
earlier, then checking whether ATTR_RECORD's name is within bounds.
What's more, this patch also add some comments to improve its
maintainability.
Patch series "ntfs: fix bugs about Attribute", v2.
This patchset fixes three bugs relative to Attribute in record:
Patch 1 adds a sanity check to ensure that, attrs_offset field in first
mft record loading from disk is within bounds.
Patch 2 moves the ATTR_RECORD's bounds checking earlier, to avoid
dereferencing ATTR_RECORD before checking this ATTR_RECORD is within
bounds.
Patch 3 adds an overflow checking to avoid possible forever loop in
ntfs_attr_find().
Without patch 1 and patch 2, the kernel triggersa KASAN use-after-free
detection as reported by Syzkaller.
Although one of patch 1 or patch 2 can fix this, we still need both of
them. Because patch 1 fixes the root cause, and patch 2 not only fixes
the direct cause, but also fixes the potential out-of-bounds bug.
This patch (of 3):
Syzkaller reported use-after-free read as follows:
==================================================================
BUG: KASAN: use-after-free in ntfs_attr_find+0xc02/0xce0 fs/ntfs/attrib.c:597
Read of size 2 at addr ffff88807e352009 by task syz-executor153/3607
Kernel will loads $MFT/$DATA's first mft record in
ntfs_read_inode_mount().
Yet the problem is that after loading, kernel doesn't check whether
attrs_offset field is a valid value.
To be more specific, if attrs_offset field is larger than bytes_allocated
field, then it may trigger the out-of-bounds read bug(reported as
use-after-free bug) in ntfs_attr_find(), when kernel tries to access the
corresponding mft record's attribute.
This patch solves it by adding the sanity check between attrs_offset field
and bytes_allocated field, after loading the first mft record.
Functions implementing the a_ops->write_end() interface accept the `void
*fsdata` parameter that is supposed to be initialized by the corresponding
a_ops->write_begin() (which accepts `void **fsdata`).
However not all a_ops->write_begin() implementations initialize `fsdata`
unconditionally, so it may get passed uninitialized to a_ops->write_end(),
resulting in undefined behavior.
Fix this by initializing fsdata with NULL before the call to
write_begin(), rather than doing so in all possible a_ops implementations.
This patch covers only the following cases found by running x86 KMSAN
under syzkaller:
- generic_perform_write()
- cont_expand_zero() and generic_cont_expand_simple()
- page_symlink()
Other cases of passing uninitialized fsdata may persist in the codebase.
Link: https://lkml.kernel.org/r/20220915150417.722975-43-glider@google.com Signed-off-by: Alexander Potapenko <glider@google.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Konovalov <andreyknvl@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Borislav Petkov <bp@alien8.de> Cc: Christoph Hellwig <hch@lst.de> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Eric Biggers <ebiggers@kernel.org> Cc: Eric Dumazet <edumazet@google.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Ilya Leoshkevich <iii@linux.ibm.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Marco Elver <elver@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vegard Nossum <vegard.nossum@oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting hung task at p9_fd_close() [1], for p9_mux_poll_stop()
from p9_conn_destroy() from p9_fd_close() is failing to interrupt already
started kernel_read() from p9_fd_read() from p9_read_work() and/or
kernel_write() from p9_fd_write() from p9_write_work() requests.
Since p9_socket_open() sets O_NONBLOCK flag, p9_mux_poll_stop() does not
need to interrupt kernel_read()/kernel_write(). However, since p9_fd_open()
does not set O_NONBLOCK flag, but pipe blocks unless signal is pending,
p9_mux_poll_stop() needs to interrupt kernel_read()/kernel_write() when
the file descriptor refers to a pipe. In other words, pipe file descriptor
needs to be handled as if socket file descriptor.
We somehow need to interrupt kernel_read()/kernel_write() on pipes.
A minimal change, which this patch is doing, is to set O_NONBLOCK flag
from p9_fd_open(), for O_NONBLOCK flag does not affect reading/writing
of regular files. But this approach changes O_NONBLOCK flag on userspace-
supplied file descriptors (which might break userspace programs), and
O_NONBLOCK flag could be changed by userspace. It would be possible to set
O_NONBLOCK flag every time p9_fd_read()/p9_fd_write() is invoked, but still
remains small race window for clearing O_NONBLOCK flag.
If we don't want to manipulate O_NONBLOCK flag, we might be able to
surround kernel_read()/kernel_write() with set_thread_flag(TIF_SIGPENDING)
and recalc_sigpending(). Since p9_read_work()/p9_write_work() works are
processed by kernel threads which process global system_wq workqueue,
signals could not be delivered from remote threads when p9_mux_poll_stop()
from p9_conn_destroy() from p9_fd_close() is called. Therefore, calling
set_thread_flag(TIF_SIGPENDING)/recalc_sigpending() every time would be
needed if we count on signals for making kernel_read()/kernel_write()
non-blocking.
Switch from strlcpy to strscpy and make sure that @count is the size of
the smaller of the source and destination buffers. This prevents
reading beyond the end of the source buffer when the source string isn't
null terminated.
Found by a modified version of syzkaller.
Suggested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fuzzers like to scribble over sb_bsize_shift but in reality it's very
unlikely that this field would be corrupted on its own. Nevertheless it
should be checked to avoid the possibility of messy mount errors due to
bad calculations. It's always a fixed value based on the block size so
we can just check that it's the expected value.
Tested with:
mkfs.gfs2 -O -p lock_nolock /dev/vdb
for i in 0 -1 64 65 32 33; do
gfs2_edit -p sb field sb_bsize_shift $i /dev/vdb
mount /dev/vdb /mnt/test && umount /mnt/test
done
and with UBSAN configured we also get complaints like
[ 76.373395] UBSAN: shift-out-of-bounds in fs/gfs2/ops_fstype.c:295:19
[ 76.373815] shift exponent 4294967287 is too large for 64-bit type 'long unsigned int'
After the patch, these complaints don't appear, mount fails immediately
and we get an explanation in dmesg.
Reported-by: syzbot+dcf33a7aae997956fe06@syzkaller.appspotmail.com Signed-off-by: Andrew Price <anprice@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sk->sk_receive_queue is protected by skb queue lock, but for KCM
sockets its RX path takes mux->rx_lock to protect more than just
skb queue. However, kcm_recvmsg() still only grabs the skb queue
lock, so race conditions still exist.
We can teach kcm_recvmsg() to grab mux->rx_lock too but this would
introduce a potential performance regression as struct kcm_mux can
be shared by multiple KCM sockets.
So we have to enforce skb queue lock in requeue_rx_msgs() and handle
skb peek case carefully in kcm_wait_data(). Fortunately,
skb_recv_datagram() already handles it nicely and is widely used by
other sockets, we can just switch to skb_recv_datagram() after
getting rid of the unnecessary sock lock in kcm_recvmsg() and
kcm_splice_read(). Side note: SOCK_DONE is not used by KCM sockets,
so it is safe to get rid of this check too.
I ran the original syzbot reproducer for 30 min without seeing any
issue.
Fixes: 01e0164f6208 ("kcm: Kernel Connection Multiplexor module") Reported-by: syzbot+278279efdd2730dd14bf@syzkaller.appspotmail.com Reported-by: shaozhengchao <shaozhengchao@huawei.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Tom Herbert <tom@herbertland.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/r/20221114005119.597905-1-xiyou.wangcong@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We got a syzkaller problem because of aarch64 alignment fault
if KFENCE enabled. When the size from user bpf program is an odd
number, like 399, 407, etc, it will cause the struct skb_shared_info's
unaligned access. As seen below:
BUG: KFENCE: use-after-free read in __skb_clone+0x23c/0x2a0 net/core/skbuff.c:1032
allocated by task 15074 on cpu 0 at 1342.585390s:
kmalloc include/linux/slab.h:568 [inline]
kzalloc include/linux/slab.h:675 [inline]
bpf_test_init.isra.0+0xac/0x290 net/bpf/test_run.c:191
bpf_prog_test_run_skb+0x11c/0xa7c net/bpf/test_run.c:512
bpf_prog_test_run kernel/bpf/syscall.c:3148 [inline]
__do_sys_bpf kernel/bpf/syscall.c:4441 [inline]
__se_sys_bpf+0xad0/0x1634 kernel/bpf/syscall.c:4381
__arm64_sys_bpf+0x50/0x60 kernel/bpf/syscall.c:4381
To fix the problem, we adjust @size so that (@size + @hearoom) is a
multiple of SMP_CACHE_BYTES. So we make sure the struct skb_shared_info
is aligned to a cache line.
syzbot found that kcm_tx_work() could crash [1] in:
/* Primarily for SOCK_SEQPACKET sockets */
if (likely(sk->sk_socket) &&
test_bit(SOCK_NOSPACE, &sk->sk_socket->flags)) {
<<*>> clear_bit(SOCK_NOSPACE, &sk->sk_socket->flags);
sk->sk_write_space(sk);
}
I think the reason is that another thread might concurrently
run in kcm_release() and call sock_orphan(sk) while sk is not
locked. kcm_tx_work() find sk->sk_socket being NULL.
[1]
BUG: KASAN: null-ptr-deref in instrument_atomic_write include/linux/instrumented.h:86 [inline]
BUG: KASAN: null-ptr-deref in clear_bit include/asm-generic/bitops/instrumented-atomic.h:41 [inline]
BUG: KASAN: null-ptr-deref in kcm_tx_work+0xff/0x160 net/kcm/kcmsock.c:742
Write of size 8 at addr 0000000000000008 by task kworker/u4:3/53
Apparently, mptcp is able to call tcp_disconnect() on an already
disconnected flow. This is generally fine, unless current congestion
control is CDG, because it might trigger a double-free [1]
Instead of fixing MPTCP, and future bugs, we can make tcp_disconnect()
more resilient.
[1]
BUG: KASAN: double-free in slab_free mm/slub.c:3539 [inline]
BUG: KASAN: double-free in kfree+0xe2/0x580 mm/slub.c:4567
macvlan should enforce a minimal mtu of 68, even at link creation.
This patch avoids the current behavior (which could lead to crashes
in ipv6 stack if the link is brought up)
$ ip link add macvlan1 link eno1 mtu 8 type macvlan # This should fail !
$ ip link sh dev macvlan1
5: macvlan1@eno1: <BROADCAST,MULTICAST> mtu 8 qdisc noop
state DOWN mode DEFAULT group default qlen 1000
link/ether 02:47:6c:24:74:82 brd ff:ff:ff:ff:ff:ff
$ ip link set macvlan1 mtu 67
Error: mtu less than device minimum.
$ ip link set macvlan1 mtu 68
$ ip link set macvlan1 mtu 8
Error: mtu less than device minimum.
Fixes: 1376e65bcf3a ("net: use core MTU range checking in core net infra") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid resetting the module-wide i8042_platform_device pointer in
i8042_probe() or i8042_remove(), so that the device can be properly
destroyed by i8042_exit() on module unload.
In __unregister_kprobe_top(), if the currently unregistered probe has
post_handler but other child probes of the aggrprobe do not have
post_handler, the post_handler of the aggrprobe is cleared. If this is
a ftrace-based probe, there is a problem. In later calls to
disarm_kprobe(), we will use kprobe_ftrace_ops because post_handler is
NULL. But we're armed with kprobe_ipmodify_ops. This triggers a WARN in
__disarm_kprobe_ftrace() and may even cause use-after-free:
For the kprobe-on-ftrace case, we keep the post_handler setting to
identify this aggrprobe armed with kprobe_ipmodify_ops. This way we
can disarm it correctly.
If device_register() fails in tcm_loop_setup_hba_bus(), the name allocated
by dev_set_name() need be freed. As comment of device_register() says, it
should use put_device() to give up the reference in the error path. So fix
this by calling put_device(), then the name can be freed in kobject_cleanup().
The 'tl_hba' will be freed in tcm_loop_release_adapter(), so it don't need
goto error label in this case.
Fixes: 0aca937055f0 ("[SCSI] tcm_loop: Add multi-fabric Linux/SCSI LLD fabric module") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221115015042.3652261-1-yangyingliang@huawei.com Reviewed-by: Mike Christie <michael.chritie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function ring_buffer_nr_dirty_pages() was created to find out how many
pages are filled in the ring buffer. There's two running counters. One is
incremented whenever a new page is touched (pages_touched) and the other
is whenever a page is read (pages_read). The dirty count is the number
touched minus the number read. This is used to determine if a blocked task
should be woken up if the percentage of the ring buffer it is waiting for
is hit.
The problem is that it does not take into account dropped pages (when the
new writes overwrite pages that were not read). And then the dirty pages
will always be greater than the percentage.
This makes the "buffer_percent" file inaccurate, as the number of dirty
pages end up always being larger than the percentage, event when it's not
and this causes user space to be woken up more than it wants to be.
Add a new counter to keep track of lost pages, and include that in the
accounting of dirty pages so that it is actually accurate.
Link: https://lkml.kernel.org/r/20221021123013.55fb6055@gandalf.local.home Fixes: 3b1e5cf0237dd ("ring-buffer: Add percentage of ring buffer full to wake up reader") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Returning true from handle_rx_dma() without flushing DMA first creates
a data ordering hazard. If DMA Rx has handled any character at the
point when RLSI occurs, the non-DMA path handles any pending characters
jumping them ahead of those characters that are pending under DMA.
Local variable ev created at:
qp_notify_peer+0x54/0x290 drivers/misc/vmw_vmci/vmci_queue_pair.c:1456
qp_broker_attach drivers/misc/vmw_vmci/vmci_queue_pair.c:1662
qp_broker_alloc+0x2977/0x2f30 drivers/misc/vmw_vmci/vmci_queue_pair.c:1750
Bytes 28-31 of 48 are uninitialized
Memory access of size 48 starts at ffff888035155e00
Data copied to user address 0000000020000100
Use memset() to prevent the infoleaks.
Also speculatively fix qp_notify_peer_local(), which may suffer from the
same problem.
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before amd_probe() returns. There is no problem for the 'smbus_dev ==
NULL' branch because pci_dev_put() can also handle the NULL input
parameter case.
Fixes: 4bb3e069dfa7 ("mmc: sdhci-pci: Build o2micro support in the same module") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221114083100.149200-1-wangxiongfeng2@huawei.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SD card is recognized failed sometimes when resume from suspend.
Because CD# debounce time too long then card present report wrong.
Finally, card is recognized failed.
In mmc_select_voltage(), if there is no full power cycle, the voltage
range selected at the end of the function will be on a single range
(e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V),
the mask shift should be reduced by 1.
This issue was triggered by using a specific SD-card (Verbatim Premium
16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes
and there is no power cycle. And the card was failing to switch to
high-speed mode. When adding the range 3.2V/3.3V for this card with the
proposed shift change, the card can switch to high-speed mode.
We used to use the wrong type of integer in 'zfcp_fsf_req_send()' to cache
the FSF request ID when sending a new FSF request. This is used in case the
sending fails and we need to remove the request from our internal hash
table again (so we don't keep an invalid reference and use it when we free
the request again).
In 'zfcp_fsf_req_send()' we used to cache the ID as 'int' (signed and 32
bit wide), but the rest of the zfcp code (and the firmware specification)
handles the ID as 'unsigned long'/'u64' (unsigned and 64 bit wide [s390x
ELF ABI]). For one this has the obvious problem that when the ID grows
past 32 bit (this can happen reasonably fast) it is truncated to 32 bit
when storing it in the cache variable and so doesn't match the original ID
anymore. The second less obvious problem is that even when the original ID
has not yet grown past 32 bit, as soon as the 32nd bit is set in the
original ID (0x80000000 = 2'147'483'648) we will have a mismatch when we
cast it back to 'unsigned long'. As the cached variable is of a signed
type, the compiler will choose a sign-extending instruction to load the 32
bit variable into a 64 bit register (e.g.: 'lgf %r11,188(%r15)'). So once
we pass the cached variable into 'zfcp_reqlist_find_rm()' to remove the
request again all the leading zeros will be flipped to ones to extend the
sign and won't match the original ID anymore (this has been observed in
practice).
If we can't successfully remove the request from the hash table again after
'zfcp_qdio_send()' fails (this happens regularly when zfcp cannot notify
the adapter about new work because the adapter is already gone during
e.g. a ChpID toggle) we will end up with a double free. We unconditionally
free the request in the calling function when 'zfcp_fsf_req_send()' fails,
but because the request is still in the hash table we end up with a stale
memory reference, and once the zfcp adapter is either reset during recovery
or shutdown we end up freeing the same memory twice.
The resulting stack traces vary depending on the kernel and have no direct
correlation to the place where the bug occurs. Here are three examples that
have been seen in practice:
To fix this, simply change the type of the cache variable to 'unsigned
long', like the rest of zfcp and also the argument for
'zfcp_reqlist_find_rm()'. This prevents truncation and wrong sign extension
and so can successfully remove the request from the hash table.
Fixes: 3f417d1bf9ff ("[SCSI] zfcp: Remove function zfcp_reqlist_find_safe") Cc: <stable@vger.kernel.org> #v2.6.34+ Signed-off-by: Benjamin Block <bblock@linux.ibm.com> Link: https://lore.kernel.org/r/979f6e6019d15f91ba56182f1aaf68d61bf37fc6.1668595505.git.bblock@linux.ibm.com Reviewed-by: Steffen Maier <maier@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting uninitialized value at iforce_init_device() [1], for
commit 2fcf38d9c120 ("Input: iforce - allow callers supply data buffer
when fetching device IDs") is checking that valid length is shorter than
bytes to read. Since iforce_get_id_packet() stores valid length when
returning 0, the caller needs to check that valid length is longer than or
equals to bytes to read.
If the platform doesn't use DMA device filter (as is the case with
Elkhart Lake), whole lpss8250_dma_setup() setup is skipped. This
results in skipping also *_maxburst setup which is undesirable.
Refactor lpss8250_dma_setup() to configure DMA even if filter is not
setup.
DW UART sometimes triggers IIR_RDI during DMA Rx when IIR_RX_TIMEOUT
should have been triggered instead. Since IIR_RDI has higher priority
than IIR_RX_TIMEOUT, this causes the Rx to hang into interrupt loop.
The problem seems to occur at least with some combinations of
small-sized transfers (I've reproduced the problem on Elkhart Lake PSE
UARTs).
If there's already an on-going Rx DMA and IIR_RDI triggers, fall
graciously back to non-DMA Rx. That is, behave as if IIR_RX_TIMEOUT had
occurred.
8250_omap already considers IIR_RDI similar to this change so its
nothing unheard of.
Fixes: 06dcb8934ce4 ("serial: 8250_dma: Fix RX handling") Cc: <stable@vger.kernel.org> Co-developed-by: Srikanth Thokala <srikanth.thokala@intel.com> Signed-off-by: Srikanth Thokala <srikanth.thokala@intel.com> Co-developed-by: Aman Kumar <aman.kumar@intel.com> Signed-off-by: Aman Kumar <aman.kumar@intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20221108121952.5497-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__list_versions will first estimate the required space using the
"dm_target_iterate(list_version_get_needed, &needed)" call and then will
fill the space using the "dm_target_iterate(list_version_get_info,
&iter_info)" call. Each of these calls locks the targets using the
"down_read(&_lock)" and "up_read(&_lock)" calls, however between the first
and second "dm_target_iterate" there is no lock held and the target
modules can be loaded at this point, so the second "dm_target_iterate"
call may need more space than what was the first "dm_target_iterate"
returned.
The code tries to handle this overflow (see the beginning of
list_version_get_info), however this handling is incorrect.
The code sets "param->data_size = param->data_start + needed" and
"iter_info.end = (char *)vers+len" - "needed" is the size returned by the
first dm_target_iterate call; "len" is the size of the buffer allocated by
userspace.
"len" may be greater than "needed"; in this case, the code will write up
to "len" bytes into the buffer, however param->data_size is set to
"needed", so it may write data past the param->data_size value. The ioctl
interface copies only up to param->data_size into userspace, thus part of
the result will be truncated.
Fix this bug by setting "iter_info.end = (char *)vers + needed;" - this
guarantees that the second "dm_target_iterate" call will write only up to
the "needed" buffer and it will exit with "DM_BUFFER_FULL_FLAG" if it
overflows the "needed" space - in this case, userspace will allocate a
larger buffer and retry.
Note that there is also a bug in list_version_get_needed - we need to add
"strlen(tt->name) + 1" to the needed size, not "strlen(tt->name)".
dev_set_name() allocates memory for name, it need be freed
when device_add() fails, call put_device() to give up the
reference that hold in device_initialize(), so that it can
be freed in kobject_cleanup() when the refcount hit to 0.
If iio_trigger_register() returns error, it should call iio_trigger_free()
to give up the reference that hold in iio_trigger_alloc(), so that it can
call iio_trig_release() to free memory when the refcount hit to 0.
We hold ci->lock in position (1) and use hrtimer_cancel() to
wait ci_otg_hrtimer_func() to stop, but ci_otg_hrtimer_func()
also need ci->lock in position (2). As a result, the
hrtimer_cancel() in ci_otg_del_timer() will be blocked forever.
This patch extracts hrtimer_cancel() from the protection of
spin_lock_irqsave() in order that the ci_otg_hrtimer_func()
could obtain the ci->lock.
What`s more, there will be no race happen. Because the
"next_timer" is always under the protection of
spin_lock_irqsave() and we only check whether "next_timer"
equals to NUM_OTG_FSM_TIMERS in the following code.
Before adding this quirk, this (mechanical keyboard) device would not be
recognized, logging:
new full-speed USB device number 56 using xhci_hcd
unable to read config index 0 descriptor/start: -32
chopping to 0 config(s)
It would take dozens of plugging/unpuggling cycles for the keyboard to
be recognized. Keyboard seems to simply work after applying this quirk.
This issue had been reported by users in two places already ([1], [2])
but nobody tried upstreaming a patch yet. After testing I believe their
suggested fix (DELAY_INIT + NO_LPM + DEVICE_QUALIFIER) was probably a
little overkill. I assume this particular combination was tested because
it had been previously suggested in [3], but only NO_LPM seems
sufficient for this device.
Add LARA-L6 PIDs for three different USB compositions.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In default mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
[ johan: drop PID defines in favour of comments ] Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not
implement a QMI interface on port 4, the reservation (RSVD(4)) has been
added to meet other companies that implement QMI on that interface.
LARA-R6 00B USB composition exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parser/alternative functions
Remove the UBLOX_PRODUCT_R6XX 0x90fa association since LARA-R6 00B final
product uses a new USB composition with different PID. 0x90fa PID used
only by LARA-R6 internal prototypes.
Move 0x90fa PID directly in the option_ids array since used by other
Qualcomm based modem vendors as pointed out in:
Add support for the AT and diag ports, similar to other qualcomm SDX55
modems. In QDL mode, the modem uses a different device ID and support
is provided by qcserial in commit ff84d45a214b ("USB: serial: qcserial:
add EM9191 QDL support").
The offending commit disabled the USB core PHY management as the dwc3
already manages the PHYs in question.
Unfortunately some platforms have started relying on having USB core
also controlling the PHY and this is specifically currently needed on
some Exynos platforms for PHY calibration or connected device may fail
to enumerate.
The PHY calibration was previously handled in the dwc3 driver, but to
work around some issues related to how the dwc3 driver interacts with
xhci (e.g. using multiple drivers) this was moved to USB core by commits d644632156bf ("usb: core: phy: add support for PHY calibration") and b0897686c7b6 ("usb: dwc3: remove generic PHY calibrate() calls").
The same PHY obviously should not be controlled from two different
places, which for example do no agree on the PHY mode or power state
during suspend, but as the offending patch was backported to stable,
let's revert it for now.
snd_usbmidi_output_open() has a check of the NULL port with
snd_BUG_ON(). snd_BUG_ON() was used as this shouldn't have happened,
but in reality, the NULL port may be seen when the device gives an
invalid endpoint setup at the descriptor, hence the driver skips the
allocation. That is, the check itself is valid and snd_BUG_ON()
should be dropped from there. Otherwise it's confusing as if it were
a real bug, as recently syzbot stumbled on it.
The @ftrace_mod is allocated by kzalloc(), so both the members {prev,next}
of @ftrace_mode->list are NULL, it's not a valid state to call list_del().
If kstrdup() for @ftrace_mod->{func|module} fails, it goes to @out_free
tag and calls free_ftrace_mod() to destroy @ftrace_mod, then list_del()
will write prev->next and next->prev, where null pointer dereference
happens.
If the returning value of SMB2_set_info_init is an error-value,
exit the function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: a14e6f7f4ff8 ("cifs: use a compound for setting an xattr") Signed-off-by: Anastasia Belova <abelova@astralinux.ru> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A problem about insmod thunderbolt-net failed is triggered with following
log given while lsmod does not show thunderbolt_net:
insmod: ERROR: could not insert module thunderbolt-net.ko: File exists
The reason is that tbnet_init() returns tb_register_service_driver()
directly without checking its return value, if tb_register_service_driver()
failed, it returns without removing property directory, resulting the
property directory can never be created later.
Fix by remove property directory when tb_register_service_driver() returns
error.
Fixes: 8231206ef815 ("net: Add support for networking over Thunderbolt cable") Signed-off-by: Yuan Can <yuancan@huawei.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
x25_lapb_receive_frame() using skb_copy() to get a private copy of
skb, the new skb should be freed in the undersized/fragmented skb
error handling path. Otherwise there is a memory leak.
The current logic in the Intel PMC driver will forcefully attach it
when detecting any CPU on the intel_pmc_core_platform_ids array,
even if the matching ACPI device is not present.
There's no checking in pmc_core_probe() to assert that the PMC device
is present, and hence on virtualized environments the PMC device
probes successfully, even if the underlying registers are not present.
Before commit e86d48fb6227 ("platform/x86: intel_pmc_core: Substitute PCI
with CPUID enumeration") the driver would check for the presence of a
specific PCI device, and that prevented the driver from attaching when
running virtualized.
Fix by only forcefully attaching the PMC device when not running
virtualized. Note that virtualized platforms can still get the device
to load if the appropriate ACPI device is present on the tables
provided to the VM.
Make an exception for the Xen initial domain, which does have full
hardware access, and hence can attach to the PMC if present.
Fixes: e86d48fb6227 ("platform/x86: intel_pmc_core: Substitute PCI with CPUID enumeration") Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Acked-by: David E. Box <david.e.box@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20221110163145.80374-1-roger.pau@citrix.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In device_add(), dev_set_name() is called to allocate name, if it returns
error, the name need be freed. As comment of device_register() says, it
should use put_device() to give up the reference in the error path. So fix
this by calling put_device(), then the name can be freed in kobject_cleanup().
When pci_register_driver failed, we need to remove debugfs,
which will caused a resource leak, fix it.
Resource leak logs as follows:
[ 52.184456] debugfs: Directory 'bnxt_en' with parent '/' already present!
Fixes: 57aece0f11d7 ("bnxt_en: add debugfs support for DIM") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When connecting to client timeout, disconnect client for twice in
chnl_net_open(). Remove one. Compile tested only.
Fixes: 29db29f3a202 ("caif: Use link layer MTU instead of fixed MTU") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
hlist_for_each_entry_rcu() has built-in RCU and lock checking.
Pass cond argument to hlist_for_each_entry_rcu() to silence false
lockdep warning when CONFIG_PROVE_RCU_LIST is enabled.
Execute as follow:
ip link add link eth0 type macvlan mode source macaddr add <MAC-ADDR>
The rtnl_lock is held when macvlan_hash_lookup_source() or
macvlan_fill_info_macaddr() are called in the non-RCU read side section.
So, pass lockdep_rtnl_is_held() to silence false lockdep warning.
Fixes: fe178a01da16 ("macvlan: add source mode") Signed-off-by: Chuang Wang <nashuiliang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should not release reference by put_device() before calling device_initialize().
Fixes: 0dbf43dff27e ("mISDN: fix possible memory leak in mISDN_register_device()") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Afer commit 13e0419aca34 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
use put_device() to give up the reference, so that the name can be
freed in kobject_cleanup() when the refcount is 0.
The 'entry' is going to be freed in mISDN_dsp_dev_release(), so the
kfree() is removed. list_del() is called in mISDN_dsp_dev_release(),
so it need be initialized.
Fixes: 13e0419aca34 ("driver core: get rid of struct device's bus_id string array") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221109132832.3270119-1-yangyingliang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
netdev is allocated in bgmac_alloc() with devm_alloc_etherdev() and will
be auto released in ->remove and ->probe failure path. Using free_netdev()
in bgmac_enet_remove() leads to double free.
Fixes: 2cc7abab1a0f ("net: bgmac: allocate struct bgmac just once & don't copy it") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20221109150136.2991171-1-weiyongjun@huaweicloud.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the error path in ata_tport_add(), when calling put_device(),
ata_tport_release() is called, it will put the refcount of 'ap->host'.
And then ata_host_put() is called again, the refcount is decreased
to 0, ata_host_release() is called, all ports are freed and set to
null.
When unbinding the device after failure, ata_host_stop() is called
to release the resources, it leads a null-ptr-deref(), because all
the ports all freed and null.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
CPU: 7 PID: 18671 Comm: modprobe Kdump: loaded Tainted: G E 6.1.0-rc3+ #8
pstate: 80400009 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ata_host_stop+0x3c/0x84 [libata]
lr : release_nodes+0x64/0xd0
Call trace:
ata_host_stop+0x3c/0x84 [libata]
release_nodes+0x64/0xd0
devres_release_all+0xbc/0x1b0
device_unbind_cleanup+0x20/0x70
really_probe+0x158/0x320
__driver_probe_device+0x84/0x120
driver_probe_device+0x44/0x120
__driver_attach+0xb4/0x220
bus_for_each_dev+0x78/0xdc
driver_attach+0x2c/0x40
bus_add_driver+0x184/0x240
driver_register+0x80/0x13c
__pci_register_driver+0x4c/0x60
ahci_pci_driver_init+0x30/0x1000 [ahci]
Fix this by removing redundant ata_host_put() in the error path.
Fixes: e0b5b9dfb61c ("libata: add refcounting to ata_host") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The NAND controller size-cells should be 0 per DT bindings.
Fix the following warning produces by DT bindings check:
"
nand-controller@33002000: #size-cells:0:0: 0 was expected
nand-controller@33002000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
"
The NAND controller size-cells should be 0 per DT bindings.
Fix the following warning produces by DT bindings check:
"
nand-controller@33002000: #size-cells:0:0: 0 was expected
nand-controller@33002000: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
"
Fix the missing space in node name too.
Match the data type of a temporary holding a reference to the FIFO port
with the type of the original reference coming from `struct parport',
avoiding data truncation with LP64 ports such as SPARC64 that refer to
PCI port I/O locations via their corresponding MMIO addresses and will
therefore have non-zero bits in the high 32-bit part of the reference.
And in any case it is cleaner to have the data types matching here.
If device_register() returns error in siox_device_add(),
the name allocated by dev_set_name() need be freed. As
comment of device_register() says, it should use put_device()
to give up the reference in the error path. So fix this
by calling put_device(), then the name can be freed in
kobject_cleanup(), and sdevice is freed in siox_device_release(),
set it to null in error path.
Fixes: 97987337042b ("siox: new driver framework for eckelmann SIOX") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20221104021334.618189-1-yangyingliang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In accordance with [1] the DMA-able memory buffers must be
cacheline-aligned otherwise the cache writing-back and invalidation
performed during the mapping may cause the adjacent data being lost. It's
specifically required for the DMA-noncoherent platforms [2]. Seeing the
opal_dev.{cmd,resp} buffers are implicitly used for DMAs in the NVME and
SCSI/SD drivers in framework of the nvme_sec_submit() and sd_sec_submit()
methods respectively they must be cacheline-aligned to prevent the denoted
problem. One of the option to guarantee that is to kmalloc the buffers
[2]. Let's explicitly allocate them then instead of embedding into the
opal_dev structure instance.
Note this fix was inspired by the commit 30b8bd365b4a ("nvme-hwmon:
kmalloc the NVME SMART log buffer").
The function gsm_dlci_t1() is a timer handler that runs in an
atomic context, but it calls "kzalloc(..., GFP_KERNEL)" that
may sleep. As a result, the sleep-in-atomic-context bug will
happen. The process is shown below:
Rebinding 8250_omap in a loop will at some point produce a warning for
kernel/power/qos.c:296 cpu_latency_qos_update_request() with error
"cpu_latency_qos_update_request called for unknown object". Let's flush
the possibly pending PM QOS work scheduled from omap8250_runtime_suspend()
before we disable runtime PM.
On remove, we get an error for "Runtime PM usage count underflow!". I guess
this driver is mostly built-in, and this issue has gone unnoticed for a
while. Somehow I did not catch this issue with my earlier fix done with
commit afc5aa7b6470 ("serial: 8250_omap: Fix probe and remove for PM
runtime").
Fixes: afc5aa7b6470 ("serial: 8250_omap: Fix probe and remove for PM runtime") Signed-off-by: Tony Lindgren <tony@atomide.com>
Depends-on: c4a28fe77ffc ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter") Link: https://lore.kernel.org/r/20221028105813.54290-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We were occasionally seeing the "Errata i202: timedout" on an AM335x
board when repeatedly opening and closing a UART connected to an active
sender. As new input may arrive at any time, it is possible to miss the
"RX FIFO empty" condition, forcing the loop to wait until it times out.
Nothing in the i202 Advisory states that such a wait is even necessary;
other FIFO clear functions like serial8250_clear_fifos() do not wait
either. For this reason, it seems safe to remove the wait, fixing the
mentioned issue.
BUG: KASAN: use-after-free in device_del+0xb5b/0xc60
Read of size 8 at addr ffff888008655050 by task rmmod/387
CPU: 2 PID: 387 Comm: rmmod
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996)
Call Trace:
<TASK>
dump_stack_lvl+0x79/0x9a
print_report+0x17f/0x47b
kasan_report+0xbb/0xf0
device_del+0xb5b/0xc60
platform_device_del.part.0+0x24/0x200
platform_device_unregister+0x2e/0x40
snd_soc_exit+0xa/0x22 [snd_soc_core]
__do_sys_delete_module.constprop.0+0x34f/0x5b0
do_syscall_64+0x3a/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
...
</TASK>
It's bacause in snd_soc_init(), snd_soc_util_init() is possble to fail,
but its ret is ignored, which makes soc_dummy_dev unregistered twice.
snd_soc_init()
snd_soc_util_init()
platform_device_register_simple(soc_dummy_dev)
platform_driver_register() # fail
platform_device_unregister(soc_dummy_dev)
platform_driver_register() # success
...
snd_soc_exit()
snd_soc_util_exit()
# soc_dummy_dev will be unregistered for second time
To fix it, handle error and stop snd_soc_init() when util_init() fail.
Also clean debugfs when util_init() or driver_register() fail.
Fixes: e2e49ab152be ("ASoC: Work around allmodconfig failure") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com> Link: https://lore.kernel.org/r/20221028031603.59416-1-chenzhongjin@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes: 5e75d576a13b6 ("spi: stm32: Rate-limit the 'Communication suspended' message") Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two spelling mistakes in codec routing description. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Acked-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20221019071639.1003730-1-colin.i.king@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
l2cap_global_chan_by_psm shall not return fixed channels as they are not
meant to be connected by (S)PSM.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Several places in the qgroup self tests follow the pattern of freeing the
ulist pointer they passed to btrfs_find_all_roots() if the call to that
function returned an error. That is pointless because that function always
frees the ulist in case it returns an error.
Also In some places like at test_multiple_refs(), after a call to
btrfs_qgroup_account_extent() we also leave "old_roots" and "new_roots"
pointing to ulists that were freed, because btrfs_qgroup_account_extent()
has freed those ulists, and if after that the next call to
btrfs_find_all_roots() fails, we call ulist_free() on the "old_roots"
ulist again, resulting in a double free.
So remove those calls to reduce the code size and avoid double ulist
free in case of an error.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mode_valid field in drm_connector_helper_funcs is expected to be of
type:
enum drm_mode_status (* mode_valid) (struct drm_connector *connector,
struct drm_display_mode *mode);
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of imx_tve_connector_mode_valid should be changed from
int to enum drm_mode_status.
Dell Vostro 5568 laptop has lis3lv02d, but its i2c address is not known
to the kernel. Add this address.
Output of "cat /sys/devices/platform/lis3lv02d/position" on Dell Vostro
5568 laptop:
- Horizontal: (-18,0,1044)
- Front elevated: (522,-18,1080)
- Left elevated: (-18,-360,1080)
- Upside down: (36,108,-1134)
Signed-off-by: Nam Cao <namcaov@gmail.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Reviewed-by: Pali Rohár <pali@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's a small window where a LOCK sent during a delegation return can
race with another OPEN on client, but the open stateid has not yet been
updated. In this case, the client doesn't handle the OLD_STATEID error
from the server and will lose this lock, emitting:
"NFS: nfs4_handle_delegation_recall_error: unhandled error -10024".
Fix this by sending the task through the nfs4 error handling in
nfs4_lock_done() when we may have to reconcile our stateid with what the
server believes it to be. For this case, the result is a retry of the
LOCK operation with the updated stateid.
Reported-by: Gonzalo Siero Humet <gsierohu@redhat.com> Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't use the test-specific header files as source files to force a
target dependency, as clang will complain if more than one source file
is used for a compile command with a single '-o' flag.
Use the proper Makefile variables instead as defined in
tools/testing/selftests/lib.mk.
Line In Bypass control is used as Master Capture at the moment
this is completely incorrect.
Current control routed to Mixer instead of ADC, thus can't affect
Capture path. ADC control shall be used instead.
ADC volume control parameters are different, so the patch fixes that
as well. Manual says (16.6.3.2 Programmable input attenuation amplifier:
PGATM) that gain varies in range 0dB..22.5dB with 1.5dB step.
DAC volume control is the Master Playback Volume at the moment
and it reports wrong levels in alsamixer and other alsa apps.
The patch fixes that, as stated in manual on the jz4725b SoC
(16.6.3.4 Programmable attenuation: GOD) the ctl range varies
from -22.5dB to 0dB with 1.5dB step.
According to documentation, the 64K erase opcode is located in VSCC
range [16:23] instead of [8:15].
Use the proper value to shift the mask over the correct range.
In wm8962 driver, the WM8962_ADDITIONAL_CONTROL_4 is used as a volatile
register, but this register mixes a bunch of volatile status bits and a
bunch of non-volatile control bits. The dapm widgets TEMP_HP and
TEMP_SPK leverages the control bits in this register. After the wm8962
probe, the regmap will bet set to cache only mode, then a read error
like below would be triggered when trying to read the initial power
state of the dapm widgets TEMP_HP and TEMP_SPK.
wm8962 0-001a: ASoC: error at soc_component_read_no_lock
on wm8962.0-001a: -16
In order to fix this issue, we add event handler to actually power
up/down these widgets. With this change, we also need to explicitly
power off these widgets in the wm8962 probe since they are enabled
by default.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com> Tested-by: Adam Ford <aford173@gmail.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20221010092014.2229246-1-xiaolei.wang@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / kernel.git / log