mlxsw: spectrum: Add support for 400Gbps (50Gbps per lane) link modes

Extend speed support with 400Gbps

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: Add support for 400Gbps (50Gbps per lane) link modes

Add support for 400Gbps speed, link modes of 50Gbps per lane

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Update address for vrf and l3mdev in MAINTAINERS

Use my kernel.org address for all entries in MAINTAINERS.

Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'Scatter-gather-SPI-for-SJA1105-DSA'

Vladimir Oltean says:

====================
Scatter/gather SPI for SJA1105 DSA

This is a small series that reduces the stack memory usage for the
sja1105 driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Switch to scatter/gather API for SPI

This reworks the SPI transfer implementation to make use of more of the
SPI core features. The main benefit is to avoid the memcpy in
sja1105_xfer_buf().

The memcpy was only needed because the function was transferring a
single buffer at a time. So it needed to copy the caller-provided buffer
at buf + 4, to store the SPI message header in the "headroom" area.

But the SPI core supports scatter-gather messages, comprised of multiple
transfers. We can actually use those to break apart every SPI message
into 2 transfers: one for the header and one for the actual payload.

To keep the behavior the same regarding the chip select signal, it is
necessary to tell the SPI core to de-assert the chip select after each
chunk. This was not needed before, because each spi_message contained
only 1 single transfer.

The meaning of the per-transfer cs_change=1 is:

- If the transfer is the last one of the message, keep CS asserted
- Otherwise, deassert CS

We need to deassert CS in the "otherwise" case, which was implicit
before.

Avoiding the memcpy creates yet another opportunity. The device can't
process more than 256 bytes of SPI payload at a time, so the
sja1105_xfer_long_buf() function used to exist, to split the larger
caller buffer into chunks.

But these chunks couldn't be used as scatter/gather buffers for
spi_message until now, because of that memcpy (we would have needed more
memory for each chunk). So we can now remove the sja1105_xfer_long_buf()
function and have a single implementation for long and short buffers.

Another benefit is lower usage of stack memory. Previously we had to
store 2 SPI buffers for each chunk. Due to the elimination of the
memcpy, we can now send pointers to the actual chunks from the
caller-supplied buffer to the SPI core.

Since the patch merges two functions into a rewritten implementation,
the function prototype was also changed, mainly for cosmetic consistency
with the structures used within it.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Move sja1105_spi_transfer into sja1105_xfer

This is a cosmetic patch that reduces some boilerplate in the SPI
interaction of the driver.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: b44: remove redundant assignment to variable reg

The variable reg is being assigned a value that is never read
and is being re-assigned in the following for-loop. The
assignment is redundant and hence can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'PTP-driver-refactoring-for-SJA1105-DSA'

Vladimir Oltean says:

====================
PTP driver refactoring for SJA1105 DSA

This series creates a better separation between the driver core and the
PTP portion. Therefore, users who are not interested in PTP can get a
simpler and smaller driver by compiling it out.

This is in preparation for further patches: SPI transfer timestamping,
synchronizing the hardware clock (as opposed to keeping it
free-running), PPS input/output, etc.
====================

Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Change the PTP command access pattern

The PTP command register contains enable bits for:
- Putting the 64-bit PTPCLKVAL register in add/subtract or write mode
- Taking timestamps off of the corrected vs free-running clock
- Starting/stopping the TTEthernet scheduling
- Starting/stopping PPS output
- Resetting the switch

When a command needs to be issued (e.g. "change the PTPCLKVAL from write
mode to add/subtract mode"), one cannot simply write to the command
register setting the PTPCLKADD bit to 1, because that would zeroize the
other settings. One also cannot do a read-modify-write (that would be
too easy for this hardware) because not all bits of the command register
are readable over SPI.

So this leaves us with the only option of keeping the value of the PTP
command register in the driver, and operating on that.

Actually there are 2 types of PTP operations now:
- Operations that modify the cached PTP command. These operate on
  ptp_data->cmd as a pointer.
- Operations that apply all previously cached PTP settings, but don't
  otherwise cache what they did themselves. The sja1105_ptp_reset
  function is such an example. It copies the ptp_data->cmd on stack
  before modifying and writing it to SPI.

This practically means that struct sja1105_ptp_cmd is no longer an
implementation detail, since it needs to be stored in full into struct
sja1105_ptp_data, and hence in struct sja1105_private. So the (*ptp_cmd)
function prototype can change and take struct sja1105_ptp_cmd as second
argument now.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Move PTP data to its own private structure

This is a non-functional change with 2 goals (both for the case when
CONFIG_NET_DSA_SJA1105_PTP is not enabled):

- Reduce the size of the sja1105_private structure.
- Make the PTP code more self-contained.

Leaving priv->ptp_data.lock to be initialized in sja1105_main.c is not a
leftover: it will be used in a future patch "net: dsa: sja1105: Restore
PTP time after switch reset".

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Make all public PTP functions take dsa_switch as argument

The new rule (as already started for sja1105_tas.h) is for functions of
optional driver components (ones which may be disabled via Kconfig - PTP
and TAS) to take struct dsa_switch *ds instead of struct sja1105_private
*priv as first argument.

This is so that forward-declarations of struct sja1105_private can be
avoided.

So make sja1105_ptp.h the second user of this rule.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: sja1105: Get rid of global declaration of struct ptp_clock_info

We need priv->ptp_caps to hold a structure and not just a pointer,
because we use container_of in the various PTP callbacks.

Therefore, the sja1105_ptp_caps structure declared in the global memory
of the driver serves no further purpose after copying it into
priv->ptp_caps.

So just populate priv->ptp_caps with the needed operations and remove
sja1105_ptp_caps.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next

Alexei Starovoitov says:

====================
pull-request: bpf-next 2019-10-14

The following pull-request contains BPF updates for your *net-next* tree.

12 days of development and
85 files changed, 1889 insertions(+), 1020 deletions(-)

The main changes are:

1) auto-generation of bpf_helper_defs.h, from Andrii.

2) split of bpf_helpers.h into bpf_{helpers, helper_defs, endian, tracing}.h
   and move into libbpf, from Andrii.

3) Track contents of read-only maps as scalars in the verifier, from Andrii.

4) small x86 JIT optimization, from Daniel.

5) cross compilation support, from Ivan.

6) bpf flow_dissector enhancements, from Jakub and Stanislav.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-next-for-net-next-2019-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
A few more small things, nothing really stands out:
 * minstrel improvements from Felix
 * a TX aggregation simplification
 * some additional capabilities for hwsim
 * minor cleanups & docs updates
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

genetlink: do not parse attributes for families with zero maxattr

Commit 61a1afebc302 ("net: genetlink: push attrbuf allocation and parsing
to a separate function") moved attribute buffer allocation and attribute
parsing from genl_family_rcv_msg_doit() into a separate function
genl_family_rcv_msg_attrs_parse() which, unlike the previous code, calls
__nlmsg_parse() even if family->maxattr is 0 (i.e. the family does its own
parsing). The parser error is ignored and does not propagate out of
genl_family_rcv_msg_attrs_parse() but an error message ("Unknown attribute
type") is set in extack and if further processing generates no error or
warning, it stays there and is interpreted as a warning by userspace.

Dumpit requests are not affected as genl_family_rcv_msg_dumpit() bypasses
the call of genl_family_rcv_msg_attrs_parse() if family->maxattr is zero.
Move this logic inside genl_family_rcv_msg_attrs_parse() so that we don't
have to handle it in each caller.

v3: put the check inside genl_family_rcv_msg_attrs_parse()
v2: adjust also argument of genl_family_rcv_msg_attrs_free()

Fixes: 61a1afebc302 ("net: genetlink: push attrbuf allocation and parsing to a separate function")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: improve recv_skip_hint for tcp_zerocopy_receive

tcp_zerocopy_receive() rounds down the zc->length a multiple of
PAGE_SIZE. This results in two issues:
- tcp_zerocopy_receive sets recv_skip_hint to the length of the
  receive queue if the zc->length input is smaller than the
  PAGE_SIZE, even though the data in receive queue could be
  zerocopied.
- tcp_zerocopy_receive would set recv_skip_hint of 0, in cases
  where we have a little bit of data after the perfectly-sized
  packets.

To fix these issues, do not store the rounded down value in
zc->length. Round down the length passed to zap_page_range(),
and return min(inq, zc->length) when the zap_range is 0.

Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'selftests-bpf-Makefile-cleanup'

Andrii Nakryiko says:

====================
Patch #1 enforces libbpf build to have bpf_helper_defs.h ready before test BPF
programs are built.
Patch #2 drops obsolete BTF/pahole detection logic from Makefile.

v1->v2:
- drop CPU and PROBE (Martin).
====================

Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

selftests/bpf: Remove obsolete pahole/BTF support detection

Given lots of selftests won't work without recent enough Clang/LLVM that
fully supports BTF, there is no point in maintaining outdated BTF
support detection and fall-back to pahole logic. Just assume we have
everything we need.

Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011220146.3798961-3-andriin@fb.com

selftests/bpf: Enforce libbpf build before BPF programs are built

Given BPF programs rely on libbpf's bpf_helper_defs.h, which is
auto-generated during libbpf build, libbpf build has to happen before
we attempt progs/*.c build. Enforce it as order-only dependency.

Fixes: 2cf90ad4a669 ("libbpf: auto-generate list of BPF helper definitions")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011220146.3798961-2-andriin@fb.com

Merge branch 'samples-cross-compile'

Ivan Khoronzhuk says:

====================
This series contains mainly fixes/improvements for cross-compilation
but not only, tested for arm, arm64, and intended for any arch.
Also verified on native build (not cross compilation) for x86_64
and arm, arm64.

Initial RFC link:
https://lkml.org/lkml/2019/8/29/1665

Prev. version:
https://lkml.org/lkml/2019/10/9/1045

Besides the patches given here, the RFC also contains couple patches
related to llvm clang
  arm: include: asm: swab: mask rev16 instruction for clang
  arm: include: asm: unified: mask .syntax unified for clang
They are necessarily to verify arm 32 build.

Also, couple more fixes were added but are not merged in bpf-next yet,
they can be needed for verification/configuration steps, if not in
your tree the fixes can be taken here:
https://www.spinics.net/lists/netdev/msg601716.html
https://www.spinics.net/lists/netdev/msg601714.html
https://www.spinics.net/lists/linux-kbuild/msg23468.html

Now, to build samples, SAMPLE_BPF should be enabled in config.

The change touches not only cross-compilation and can have impact on
other archs and build environments, so might be good idea to verify
it in order to add appropriate changes, some warn options could be
tuned also.

All is tested on x86-64 with clang installed (has to be built containing
targets for arm, arm64..., see llc --version, usually it's present already)

Instructions to test native on x86_64
=================================================
Native build on x86_64 is done in usual way and shouldn't have difference
except HOSTCC is now printed as CC wile building the samples.

Instructions to test cross compilation on arm64
=================================================
gcc version 8.3.0
(GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))

I've used sdk for TI am65x got here:
http://downloads.ti.com/processor-sdk-linux/esd/AM65X/latest/exports/\
ti-processor-sdk-linux-am65xx-evm-06.00.00.07-Linux-x86-Install.bin

make ARCH=arm64 -C tools/ clean
make ARCH=arm64 -C samples/bpf clean
make ARCH=arm64 clean
make ARCH=arm64 defconfig

make ARCH=arm64 headers_install

make ARCH=arm64 INSTALL_HDR_PATH=/../sdk/\
ti-processor-sdk-linux-am65xx-evm-06.00.00.07/linux-devkit/sysroots/\
aarch64-linux/usr headers_install

make samples/bpf/ ARCH=arm64 CROSS_COMPILE="aarch64-linux-gnu-"\
SYSROOT="/../sdk/ti-processor-sdk-linux-am65xx-evm-06.00.00.07/\
linux-devkit/sysroots/aarch64-linux"

Instructions to test cross compilation on arm
=================================================
arm-linux-gnueabihf-gcc (Linaro GCC 7.2-2017.11) 7.2.1 20171011
or
arm-linux-gnueabihf-gcc
(GNU Toolchain for the A-profile Architecture 8.3-2019.03 \
(arm-rel-8.36)) 8.3.0

http://downloads.ti.com/processor-sdk-linux/esd/AM57X/05_03_00_07/exports/\
ti-processor-sdk-linux-am57xx-evm-05.03.00.07-Linux-x86-Install.bin

make ARCH=arm -C tools/ clean
make ARCH=arm -C samples/bpf clean
make ARCH=arm clean
make ARCH=arm omap2plus_defconfig

make ARCH=arm headers_install

make ARCH=arm INSTALL_HDR_PATH=/../sdk/\
ti-processor-sdk-linux-am57xx-evm-05.03.00.07/linux-devkit/sysroots/\
armv7ahf-neon-linux-gnueabi/usr headers_install

make samples/bpf/ ARCH=arm CROSS_COMPILE="arm-linux-gnueabihf-"\
SYSROOT="/../sdk/ti-processor-sdk-linux-am57xx-evm-05.03\
.00.07/linux-devkit/sysroots/armv7ahf-neon-linux-gnueabi"

Based on bpf-next/master

v5..v4:
- any changes, only missed SOBs are added

v4..v3:
- renamed CLANG_EXTRA_CFLAGS on BPF_EXTRA_CFLAGS
- used filter for ARCH_ARM_SELECTOR
- omit "-fomit-frame-pointer" and use same flags for native and "cross"
- used sample/bpf prefixes
- use C instead of C++ compiler for test_libbpf target

v3..v2:
- renamed makefile.progs to makeifle.target, as more appropriate
- left only __LINUX_ARM_ARCH__ for D options for arm
- for host build - left options from KBUILD_HOST for compatibility reasons
- split patch adding c/cxx/ld flags to libbpf by modules
- moved readme change to separate patch
- added patch setting options for cross-compile
- fixed issue with option error for syscall_nrs.S,
  avoiding overlap for ccflags-y.

v2..v1:
- restructured patches order
- split "samples: bpf: Makefile: base progs build on Makefile.progs"
  to make change more readable. It added couple nice extra patches.
- removed redundant patch:
  "samples: bpf: Makefile: remove target for native build"
- added fix:
  "samples: bpf: makefile: fix cookie_uid_helper_example obj build"
- limited -D option filter only for arm
- improved comments
- added couple instructions to verify cross compilation for arm and
  arm64 arches based on TI am57xx and am65xx sdks.
- corrected include a little order
====================

Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>

samples/bpf: Add preparation steps and sysroot info to readme

Add couple preparation steps: clean and configuration. Also add newly
added sysroot support info to cross-compile section.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011002808.28206-16-ivan.khoronzhuk@linaro.org

samples/bpf: Add sysroot support

Basically it only enables that was added by previous couple fixes.
Sysroot contains correct libs installed and its headers. Useful when
working with NFC or virtual machine.

Usage example:

clean (on demand)
    make ARCH=arm -C samples/bpf clean
    make ARCH=arm -C tools clean
    make ARCH=arm clean

configure and install headers:

    make ARCH=arm defconfig
    make ARCH=arm headers_install

build samples/bpf:
    make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- samples/bpf/ \
    SYSROOT="path/to/sysroot"

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011002808.28206-15-ivan.khoronzhuk@linaro.org

samples/bpf: Provide C/LDFLAGS to libbpf

In order to build lib using C/LD flags of target arch, provide them
to libbpf make.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011002808.28206-14-ivan.khoronzhuk@linaro.org

libbpf: Add C/LDFLAGS to libbpf.so and test_libpf targets

In case of C/LDFLAGS there is no way to pass them correctly to build
command, for instance when --sysroot is used or external libraries
are used, like -lelf, wich can be absent in toolchain. This can be
used for samples/bpf cross-compiling allowing to get elf lib from
sysroot.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191011002808.28206-13-ivan.khoronzhuk@linaro.org

libbpf: Don't use cxx to test_libpf target

No need to use C++ for test_libbpf target when libbpf is on C and it
can be tested with C, after this change the CXXFLAGS in makefiles can
be avoided, at least in bpf samples, when sysroot is used, passing
same C/LDFLAGS as for lib.

Add "return 0" in test_libbpf to avoid warn, but also remove spaces at
start of the lines to keep same style and avoid warns while apply.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191011002808.28206-12-ivan.khoronzhuk@linaro.org

samples/bpf: Use target CC environment for HDR_PROBE

No need in hacking HOSTCC to be cross-compiler any more, so drop
this trick and use target CC for HDR_PROBE.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191011002808.28206-11-ivan.khoronzhuk@linaro.org

samples/bpf: Use own flags but not HOSTCFLAGS

While compiling natively, the host's cflags and ldflags are equal to
ones used from HOSTCFLAGS and HOSTLDFLAGS. When cross compiling it
should have own, used for target arch. While verification, for arm,
arm64 and x86_64 the following flags were used always:

-Wall -O2
-fomit-frame-pointer
-Wmissing-prototypes
-Wstrict-prototypes

So, add them as they were verified and used before adding
Makefile.target and lets omit "-fomit-frame-pointer" as were proposed
while review, as no sense in such optimization for samples.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011002808.28206-10-ivan.khoronzhuk@linaro.org

samples/bpf: Base target programs rules on Makefile.target

The main reason for that - HOSTCC and CC have different aims.
HOSTCC is used to build programs running on host, that can
cross-comple target programs with CC. It was tested for arm and arm64
cross compilation, based on linaro toolchain, but should work for
others.

So, in order to split cross compilation (CC) with host build (HOSTCC),
lets base samples on Makefile.target. It allows to cross-compile
samples/bpf programs with CC while auxialry tools running on host
built with HOSTCC.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011002808.28206-9-ivan.khoronzhuk@linaro.org

samples/bpf: Add makefile.target for separate CC target build

The Makefile.target is added only and will be used in
sample/bpf/Makefile later in order to switch cross-compiling to CC
from HOSTCC environment.

The HOSTCC is supposed to build binaries and tools running on the host
afterwards, in order to simplify build or so, like "fixdep" or else.
In case of cross compiling "fixdep" is executed on host when the rest
samples should run on target arch. In order to build binaries for
target arch with CC and tools running on host with HOSTCC, lets add
Makefile.target for simplicity, having definition and routines similar
to ones, used in script/Makefile.host. This allows later add
cross-compilation to samples/bpf with minimum changes.

The tprog stands for target programs built with CC.

Makefile.target contains only stuff needed for samples/bpf, potentially
can be reused later and now needed only for unblocking tricky
samples/bpf cross compilation.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011002808.28206-8-ivan.khoronzhuk@linaro.org

samples/bpf: Drop unnecessarily inclusion for bpf_load

Drop inclusion for bpf_load -I$(objtree)/usr/include as it is
included for all objects anyway, with above line:
KBUILD_HOSTCFLAGS += -I$(objtree)/usr/include

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191011002808.28206-7-ivan.khoronzhuk@linaro.org

samples/bpf: Use __LINUX_ARM_ARCH__ selector for arm

For arm, -D__LINUX_ARM_ARCH__=X is min version used as instruction
set selector and is absolutely required while parsing some parts of
headers. It's present in KBUILD_CFLAGS but not in autoconf.h, so let's
retrieve it from and add to programs cflags. In another case errors
like "SMP is not supported" for armv7 and bunch of other errors are
issued resulting to incorrect final object.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191011002808.28206-6-ivan.khoronzhuk@linaro.org

samples/bpf: Use own EXTRA_CFLAGS for clang commands

It can overlap with CFLAGS used for libraries built with gcc if
not now then in next patches. Correct it here for simplicity.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191011002808.28206-5-ivan.khoronzhuk@linaro.org

samples/bpf: Use --target from cross-compile

For cross compiling the target triple can be inherited from
cross-compile prefix as it's done in CLANG_FLAGS from kernel makefile.
So copy-paste this decision from kernel Makefile.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191011002808.28206-4-ivan.khoronzhuk@linaro.org

samples/bpf: Fix cookie_uid_helper_example obj build

Don't list userspace "cookie_uid_helper_example" object in list for
bpf objects.

'always' target is used for listing bpf programs, but
'cookie_uid_helper_example.o' is a user space ELF file, and covered
by rule `per_socket_stats_example`, so shouldn't be in 'always'.
Let us remove `always += cookie_uid_helper_example.o`, which avoids
breaking cross compilation due to mismatched includes.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191011002808.28206-3-ivan.khoronzhuk@linaro.org

samples/bpf: Fix HDR_PROBE "echo"

echo should be replaced with echo -e to handle '\n' correctly, but
instead, replace it with printf as some systems can't handle echo -e.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191011002808.28206-2-ivan.khoronzhuk@linaro.org

Merge branch 'netdevsim-add-devlink-health-reporters-support'

Jiri Pirko says:

====================
netdevsim: add devlink health reporters support

This patchset adds support for devlink health reporter interface
testing. First 2 patches are small dependencies of the last 2.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: add netdevsim devlink health tests

Add basic tests to verify functionality of netdevsim reporters.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdevsim: implement couple of testing devlink health reporters

Implement "empty" and "dummy" reporters. The first one is really simple
and does nothing. The other one has debugfs files to trigger breakage
and it is able to do recovery. The ops also implement dummy fmsg
content.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: propagate extack down to health reporter ops

During health reporter operations, driver might want to fill-up
the extack message, so propagate extack down to the health reporter ops.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: don't do reporter recovery if the state is healthy

If reporter state is healthy, don't call into a driver for recover and
don't increase recovery count.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: usb: ax88179_178a: write mac to hardware in get_mac_addr

When the MAC address is supplied via device tree or a random
MAC is generated it has to be written to the asix chip in
order to receive any data.

Previously in 1a7f4ce06175 ("net: usb: ax88179_178a: allow
optionally getting mac address from device tree") this line was
omitted because it seemed to work perfectly fine without it.

But it was simply not detected because the chip keeps the mac
stored even beyond a reset and it was tested on a hardware
with an integrated UPS where the asix chip was permanently
powered on even throughout power cycles.

Fixes: 1a7f4ce06175 ("net: usb: ax88179_178a: allow optionally getting mac address from device tree")
Signed-off-by: Peter Fink <pfink@christ-es.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_get_timeout: drop unnecessary return variable

Remove pointless use of size return variable by directly returning
sizes.

Signed-off-by: Vito Caputo <vcaputo@pengaru.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

af_unix: __unix_find_socket_byname() cleanup

Remove pointless return variable dance.

Appears vestigial from when the function did locking as seen in
unix_find_socket_byinode(), but locking is handled in
unix_find_socket_byname() for __unix_find_socket_byname().

Signed-off-by: Vito Caputo <vcaputo@pengaru.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-ftgmac100-Ungate-RCLK-for-RMII-on-ASPEED-MACs'

Andrew Jeffery says:

====================
net: ftgmac100: Ungate RCLK for RMII on ASPEED MACs

This series slightly extends the devicetree binding and driver for the
FTGMAC100 to describe an optional RMII RCLK gate in the clocks property.
Currently it's necessary for the kernel to ungate RCLK on the AST2600 in NCSI
configurations as u-boot does not yet support NCSI (which uses the
R(educed)MII).

v2:
* Clear up Reduced vs Reversed MII in the cover letter
* Mitigate anxiety in the commit message for 1/3
* Clarify that AST2500 is also affected in the clocks property description in
  2/3
* Rework the error paths and update some comments in 3/3

v1 can be found here: https://lore.kernel.org/netdev/20191008115143.14149-1-andrew@aj.id.au/
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: ftgmac100: Ungate RCLK for RMII on ASPEED MACs

The 50MHz RCLK has to be enabled before the RMII interface will function.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: ftgmac100: Describe clock properties

Critically, the AST2600 requires ungating the RMII RCLK if e.g. NCSI is
in use.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: ftgmac100: Document AST2600 compatible

The AST2600 contains an FTGMAC100-compatible MAC, although the MDIO
controller previously embedded in the MAC has been moved out to a
dedicated MDIO block.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

libbpf: Handle invalid typedef emitted by old GCC

Old GCC versions are producing invalid typedef for __gnuc_va_list
pointing to void. Special-case this and emit valid:

typedef __builtin_va_list __gnuc_va_list;

Reported-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20191011032901.452042-1-andriin@fb.com

libbpf: Generate more efficient BPF_CORE_READ code

Existing BPF_CORE_READ() macro generates slightly suboptimal code. If
there are intermediate pointers to be read, initial source pointer is
going to be assigned into a temporary variable and then temporary
variable is going to be uniformly used as a "source" pointer for all
intermediate pointer reads. Schematically (ignoring all the type casts),
BPF_CORE_READ(s, a, b, c) is expanded into:
({
const void *__t = src;
bpf_probe_read(&__t, sizeof(*__t), &__t->a);
bpf_probe_read(&__t, sizeof(*__t), &__t->b);

typeof(s->a->b->c) __r;
bpf_probe_read(&__r, sizeof(*__r), &__t->c);
})

This initial `__t = src` makes calls more uniform, but causes slightly
less optimal register usage sometimes when compiled with Clang. This can
cascase into, e.g., more register spills.

This patch fixes this issue by generating more optimal sequence:
({
const void *__t;
bpf_probe_read(&__t, sizeof(*__t), &src->a); /* <-- src here */
bpf_probe_read(&__t, sizeof(*__t), &__t->b);

typeof(s->a->b->c) __r;
bpf_probe_read(&__r, sizeof(*__r), &__t->c);
})

Fixes: 6632cb7d8101 ("libbpf: Add BPF_CORE_READ/BPF_CORE_READ_INTO helpers")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191011023847.275936-1-andriin@fb.com

xdp: Trivial, fix spelling in function description

Fix typo 'boolian' into 'boolean'.

Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191011084303.28418-1-anton.ivanov@cambridgegreys.com

bpf: Fix cast to pointer from integer of different size warning

Fix "warning: cast to pointer from integer of different size" when
casting u64 addr to void *.

Fixes: 46a1145a9048 ("bpf: Track contents of read-only maps as scalars")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191011172053.2980619-1-andriin@fb.com

selftests/bpf: Check that flow dissector can be re-attached

Make sure a new flow dissector program can be attached to replace the old
one with a single syscall. Also check that attaching the same program twice
is prohibited.

Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191011082946.22695-3-jakub@cloudflare.com

flow_dissector: Allow updating the flow dissector program atomically

It is currently not possible to detach the flow dissector program and
attach a new one in an atomic fashion, that is with a single syscall.
Attempts to do so will be met with EEXIST error.

This makes updates to flow dissector program hard. Traffic steering that
relies on BPF-powered flow dissection gets disrupted while old program has
been already detached but the new one has not been attached yet.

There is also a window of opportunity to attach a flow dissector to a
non-root namespace while updating the root flow dissector, thus blocking
the update.

Lastly, the behavior is inconsistent with cgroup BPF programs, which can be
replaced with a single bpf(BPF_PROG_ATTACH, ...) syscall without any
restrictions.

Allow attaching a new flow dissector program when another one is already
present with a restriction that it can't be the same program.

Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20191011082946.22695-2-jakub@cloudflare.com

bpf: Align struct bpf_prog_stats

Do not risk spanning these small structures on two cache lines.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191011181140.2898-1-edumazet@google.com

mac80211_hwsim: add support for OCB

OCB (Outside the Context of a BSS) interfaces are the
implementation of 802.11p, support that.

Signed-off-by: Ramon Fontes <ramonreisfontes@gmail.com>
Link: https://lore.kernel.org/r/20191010181307.11821-2-ramonreisfontes@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211_hwsim: add more 5GHz channels, 5/10 MHz support

These new 5GHz channels and 5/10 MHz support should be
available for OCB usage (802.11p).

Signed-off-by: Ramon Fontes <ramonreisfontes@gmail.com>
Link: https://lore.kernel.org/r/20191010181307.11821-1-ramonreisfontes@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: minstrel_ht: rename prob_ewma to prob_avg, use it for the new average

Reduces per-rate data structure size

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20191008171139.96476-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: minstrel_ht: replace rate stats ewma with a better moving average

Rate success probability usually fluctuates a lot under normal conditions.
With a simple EWMA, noise and fluctuation can be reduced by increasing the
window length, but that comes at the cost of introducing lag on sudden
changes.

This change replaces the EWMA implementation with a moving average that's
designed to significantly reduce lag while keeping a bigger window size
by being better at filtering out noise.

It is only slightly more expensive than the simple EWMA and still avoids
divisions in its calculation.

The algorithm is adapted from an implementation intended for a completely
different field (stock market trading), where the tradeoff of lag vs
noise filtering is equally important. It is based on the "smoothing filter"
from http://www.stockspotter.com/files/PredictiveIndicators.pdf.

I have adapted it to fixed-point math with some constants so that it uses
only addition, bit shifts and multiplication

To better make use of the filtering and bigger window size, the update
interval time is cut in half.

For testing, the algorithm can be reverted to the older one via debugfs

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20191008171139.96476-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: minstrel: remove divisions in tx status path

Use a slightly different threshold for downgrading spatial streams to
make it easier to calculate without divisions.
Slightly reduces CPU overhead.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20191008171139.96476-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

nl80211: trivial: Remove redundant loop

cfg80211_assign_cookie already checks & prevents a 0 from being
returned, so the explicit loop is unnecessary.

Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20191008164350.2836-1-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

ipvlan: consolidate TSO flags using NETIF_F_ALL_TSO

This will ensure that any new TSO related flags added (which
would be part of ALL_TSO mask and IPvlan driver doesn't need
to update every time new flag gets added.

Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Merge branch 'bpf-romap-known-scalars'

Andrii Nakryiko says:

====================
With BPF maps supporting direct map access (currently, array_map w/ single
element, used for global data) that are read-only both from system call and
BPF side, it's possible for BPF verifier to track its contents as known
constants.

Now it's possible for user-space control app to pre-initialize read-only map
(e.g., for .rodata section) with user-provided flags and parameters and rely
on BPF verifier to detect and eliminate dead code resulting from specific
combination of input parameters.

v1->v2:
- BPF_F_RDONLY means nothing, stick to just map->frozen (Daniel);
- stick to passing just offset into map_direct_value_addr (Martin).
====================

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

selftests/bpf: Add read-only map values propagation tests

Add tests checking that verifier does proper constant propagation for
read-only maps. If constant propagation didn't work, skipp_loop and
part_loop BPF programs would be rejected due to BPF verifier otherwise
not being able to prove they ever complete. With constant propagation,
though, they are succesfully validated as properly terminating loops.

Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191009201458.2679171-3-andriin@fb.com

bpf: Track contents of read-only maps as scalars

Maps that are read-only both from BPF program side and user space side
have their contents constant, so verifier can track referenced values
precisely and use that knowledge for dead code elimination, branch
pruning, etc. This patch teaches BPF verifier how to do this.

Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191009201458.2679171-2-andriin@fb.com

tc-testing: updated pedit test cases

Added test case for layered IP operation for a single source IP4/IP6
address and a single destination IP4/IP6 address.

Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

ptp: ptp_dte: use devm_platform_ioremap_resource() to simplify code

Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

scripts/bpf: Fix xdp_md forward declaration typo

Fix typo in struct xpd_md, generated from bpf_helpers_doc.py, which is
causing compilation warnings for programs using bpf_helpers.h

Fixes: 6cd8e1ab54d9 ("scripts/bpf: teach bpf_helpers_doc.py to dump BPF helper definitions")
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191010042534.290562-1-andriin@fb.com

team: call RCU read lock when walking the port_list

Before reading the team port list, we need to acquire the RCU read lock.
Also change list_for_each_entry() to list_for_each_entry_rcu().

v2:
repost the patch to net-next and remove fixes flag as this is a cosmetic
change.

Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: stmmac: Remove break after a return

Since break is not useful after a return, remove it.

Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net/ethernet: xgmac don't set .driver twice

Cleanup the .driver setup to just do it once, to avoid
the following sparse warning:

drivers/net/ethernet/calxeda/xgmac.c:1914:10: warning: Initializer entry defined twice
drivers/net/ethernet/calxeda/xgmac.c:1920:10:   also defined here

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Merge branch 'net-smc-improve-termination-handling'

Karsten Graul says:

====================
net/smc: improve termination handling

First set of patches to improve termination handling.
====================

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net/smc: improve close of terminated socket

Make sure a terminated SMC socket reaches the CLOSED state.
Even if sending of close flags fails, change the socket state to
the intended state to avoid dangling sockets not reaching the
CLOSED state.

Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net/smc: no new connections on disappearing devices

Add a "going_away" indication to ISM devices and IB ports and
avoid creation of new connections on such disappearing devices.

And do not handle ISM events if ISM device is disappearing.

Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net/smc: increase device refcount for added link group

SMCD link groups belong to certain ISM-devices and SMCR link group
links belong to certain IB-devices. Increase the refcount for
these devices, as long as corresponding link groups exist.

Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net/smc: separate locks for SMCD and SMCR link group lists

This patch introduces separate locks for the split SMCD and SMCR
link group lists.

Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net/smc: separate SMCD and SMCR link group lists

Currently SMCD and SMCR link groups are maintained in one list.
To facilitate abnormal termination handling they are split into
a separate list for SMCR link groups and separate lists for SMCD
link groups per SMCD device.

Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: stmmac: dwmac-mediatek: fix wrong delay value issue when resume back

mac_delay value will be divided by 550/170 in mt2712_delay_ps2stage(),
which is invoked at the beginning of mt2712_set_delay(), and the value
should be restored at the end of mt2712_set_delay().
Or, mac_delay will be divided again when invoking mt2712_set_delay()
when resume back.
So, add mt2712_delay_stage2ps() to mt2712_set_delay() to recovery the
original mac_delay value.

Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

DIM: fix dim.h kernel-doc and headers

Lots of fixes to kernel-doc in structs, enums, and functions.
Also add header files that are being used but not yet #included.

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yamin Friedman <yaminf@mellanox.com>
Cc: Tal Gilboa <talgi@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Merge branch 'sctp-add-some-missing-events-from-rfc5061'

Xin Long says:
====================
There are 4 events defined in rfc5061 missed in linux sctp:
SCTP_ADDR_ADDED, SCTP_ADDR_REMOVED, SCTP_ADDR_MADE_PRIM and
SCTP_SEND_FAILED_EVENT.

This patchset is to add them up.
====================

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

sctp: add SCTP_SEND_FAILED_EVENT event

This patch is to add a new event SCTP_SEND_FAILED_EVENT described in
rfc6458#section-6.1.11. It's a update of SCTP_SEND_FAILED event:

  struct sctp_sndrcvinfo ssf_info is replaced with
  struct sctp_sndinfo ssfe_info in struct sctp_send_failed_event.

SCTP_SEND_FAILED is being deprecated, but we don't remove it in this
patch. Both are being processed in sctp_datamsg_destroy() when the
corresp event flag is set.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

sctp: add SCTP_ADDR_MADE_PRIM event

sctp_ulpevent_nofity_peer_addr_change() would be called in
sctp_assoc_set_primary() to send SCTP_ADDR_MADE_PRIM event
when this transport is set to the primary path of the asoc.

This event is described in rfc6458#section-6.1.2:

  SCTP_ADDR_MADE_PRIM:  This address has now been made the primary
     destination address.  This notification is provided whenever an
     address is made primary.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

sctp: add SCTP_ADDR_REMOVED event

sctp_ulpevent_nofity_peer_addr_change() is called in
sctp_assoc_rm_peer() to send SCTP_ADDR_REMOVED event
when this transport is removed from the asoc.

This event is described in rfc6458#section-6.1.2:

  SCTP_ADDR_REMOVED:  The address is no longer part of the
     association.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

sctp: add SCTP_ADDR_ADDED event

A helper sctp_ulpevent_nofity_peer_addr_change() will be extracted
to make peer_addr_change event and enqueue it, and the helper will
be called in sctp_assoc_add_peer() to send SCTP_ADDR_ADDED event.

This event is described in rfc6458#section-6.1.2:

  SCTP_ADDR_ADDED:  The address is now part of the association.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

libbpf: Fix passing uninitialized bytes to setsockopt

'struct xdp_umem_reg' has 4 bytes of padding at the end that makes
valgrind complain about passing uninitialized stack memory to the
syscall:

  Syscall param socketcall.setsockopt() points to uninitialised byte(s)
    at 0x4E7AB7E: setsockopt (in /usr/lib64/libc-2.29.so)
    by 0x4BDE035: xsk_umem__create@@LIBBPF_0.0.4 (xsk.c:172)
  Uninitialised value was created by a stack allocation
    at 0x4BDDEBA: xsk_umem__create@@LIBBPF_0.0.4 (xsk.c:140)

Padding bytes appeared after introducing of a new 'flags' field.
memset() is required to clear them.

Fixes: 4128156a9b72 ("libbpf: add flags to umem config")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191009164929.17242-1-i.maximets@ovn.org

Merge branch 'btf2c-padding'

Andrii Nakryiko says:

====================
Fix BTF-to-C logic of handling padding at the end of a struct. Fix existing
test that should have captured this. Also move test_btf_dump into a test_progs
test to leverage common infrastructure.
====================

Signed-off-by: Alexei Starovoitov <ast@kernel.org>

selftests/bpf: Fix btf_dump padding test case

Existing padding test case for btf_dump has a good test that was
supposed to test padding generation at the end of a struct, but its
expected output was specified incorrectly. Fix this.

Fixes: 476eb023697e ("selftests/bpf: add btf_dump BTF-to-C conversion tests")
Reported-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191008231009.2991130-4-andriin@fb.com

selftests/bpf: Convert test_btf_dump into test_progs test

Convert test_btf_dump into a part of test_progs, instead of
a stand-alone test binary.

Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191008231009.2991130-3-andriin@fb.com

libbpf: Fix struct end padding in btf_dump

Fix a case where explicit padding at the end of a struct is necessary
due to non-standart alignment requirements of fields (which BTF doesn't
capture explicitly).

Fixes: b653ca9bf78a ("libbpf: add btf_dump API for BTF-to-C conversion")
Reported-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20191008231009.2991130-2-andriin@fb.com

net: stmmac: add flexible PPS to dwmac 4.10a

All the registers and the functionalities used in the callback
dwmac5_flex_pps_config() are common between dwmac 4.10a [1] and
5.00a [2].

Reuse the same callback for dwmac 4.10a too.

Tested on STM32MP15x, based on dwmac 4.10a.

[1] DWC Ethernet QoS Databook 4.10a October 2014
[2] DWC Ethernet QoS Databook 5.00a September 2017

Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Merge tag 'spi-ptp-api' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull in a dependency for Vladimir's work on more precise
packet time stamping.

Mark Brown says:

====================
spi: Add a PTP API

For detailed timestamping of operations.
====================

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Revert "tun: call dev_get_valid_name() before register_netdevice()"

This reverts commit eac978a17becb50733061f79f5ca101183ff148f.

As noticed by Jakub, this is no longer needed after
commit be785e0ec91f ("tun: fix memory leak in error path")

This no longer exports dev_get_valid_name() for the exclusive
use of tun driver.

Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: tipc: prepare attrs in __tipc_nl_compat_dumpit()

__tipc_nl_compat_dumpit() calls tipc_nl_publ_dump() which expects
the attrs to be available by genl_dumpit_info(cb)->attrs. Add info
struct and attr parsing in compat dumpit function.

Reported-by: syzbot+8d37c50ffb0f52941a5e@syzkaller.appspotmail.com
Fixes: 3a3cc4be2327 ("net: tipc: have genetlink code to parse the attrs during dumpit")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: genetlink: always allocate separate attrs for dumpit ops

Individual dumpit ops (start, dumpit, done) are locked by genl_lock
if !family->parallel_ops. However, multiple
genl_family_rcv_msg_dumpit() calls may in in flight in parallel.
Each has a separate struct genl_dumpit_info allocated
but they share the same family->attrbuf. Fix this by allocating separate
memory for attrs for dumpit ops, for non-parallel_ops (for parallel_ops
it is done already).

Reported-by: syzbot+495688b736534bb6c6ad@syzkaller.appspotmail.com
Reported-by: syzbot+ff59dc711f2cff879a05@syzkaller.appspotmail.com
Reported-by: syzbot+dbe02e13bcce52bcf182@syzkaller.appspotmail.com
Reported-by: syzbot+9cb7edb2906ea1e83006@syzkaller.appspotmail.com
Fixes: aa97a7fc27d2 ("net: genetlink: parse attrs and store in contect info struct during dumpit")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Merge branch 'hns3-next' into net-next

Huazhong Tan says:

====================
This patch-set includes some new features for the HNS3 ethernet
controller driver.

[patch 01/06] adds support for configuring VF link status on the host.

[patch 02/06] adds support for configuring VF spoof check.

[patch 03/06] adds support for configuring VF trust.

[patch 04/06] adds support for configuring VF bandwidth on the host.

[patch 05/06] adds support for configuring VF MAC on the host.

[patch 06/06] adds support for tx-scatter-gather-fraglist.
====================

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: support tx-scatter-gather-fraglist feature

The hardware supports up to 8 TX BD for non-tso skb and up to
63 TX BD for TSO skb. Currently, the hns3 driver supports RX skb
with fraglist when HW GRO is enabled, when the stack forwards a
RX skb with fraglist, the stack need to linearize the skb before
sending to other interface without TX fraglist support.

This patch adds support for TX fraglist. The performance increases
from 1 GByte to 1.5 GByte for one iperf TCP stream during
forwarding test after this patch. BTW, the minimum BD number of
ring should be updated to 72 for supporting TX fraglist.

This patch also changes the error handling of some function that
called by hns3_fill_desc, which returns BD num when there is no
error, change some macro to more meaningful name.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add support for configuring VF MAC from the host

This patch adds support of configuring VF MAC from the host
for the HNS3 driver.

BTW, the parameter init in the hns3_init_mac_addr is
unnecessary now, since the MAC address will not read from
NCL_CONFIG when doing reset, so it should be removed,
otherwise it will affect VF's MAC address initialization.

Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add support for configuring bandwidth of VF on the host

This patch adds support for configuring bandwidth of VF on the host
for HNS3 drivers.

Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add support for setting VF trust

This patch adds supports for setting VF trust by host. If specified
VF is trusted, then it can enable promisc(include allmulti mode).
If a trusted VF enabled promisc, and being untrusted, host will
disable promisc mode for this VF.

For VF will update its promisc mode from set_rx_mode now, so it's
unnecessary to set broadcst promisc mode when initialization or
reset.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add support for spoof check setting

This patch adds support for spoof check configuration for VFs.
When it is enabled, "spoof checking" is done for both mac address
and VLAN. For each VF, the HW ensures that the source MAC address
(or VLAN) of every outgoing packet exists in the MAC-list (or
VLAN-list) configured for RX filtering for that VF. If not,
the packet is dropped.

Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

net: hns3: add support for setting VF link status on the host

This patch adds support to configure VF link properties.
The options are auto, enable, and disable. Even if the PF
is down, the communication between VFs will be normal
if the VFs are set to enable. The commands are as follows:

'ip link set <pf> vf <vf_id> state <auto|enable|disable>'
change the VF status

'ip link show'
show the setting status

Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>