Junya Monden [Wed, 16 Oct 2019 12:42:55 +0000 (14:42 +0200)]
ASoC: rsnd: Reinitialize bit clock inversion flag for every format setting
Unlike other format-related DAI parameters, rdai->bit_clk_inv flag
is not properly re-initialized when setting format for new stream
processing. The inversion, if requested, is then applied not to default,
but to a previous value, which leads to SCKP bit in SSICR register being
set incorrectly.
Fix this by re-setting the flag to its initial value, determined by format.
Fixes: 7d91ef8fa3ed8 ("ASoC: rsnd: fixup SND_SOC_DAIFMT_xB_xF behavior") Cc: Andrew Gabbasov <andrew_gabbasov@mentor.com> Cc: Jiada Wang <jiada_wang@mentor.com> Cc: Timo Wischer <twischer@de.adit-jv.com> Cc: stable@vger.kernel.org # v3.17+ Signed-off-by: Junya Monden <jmonden@jp.adit-jv.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/20191016124255.7442-1-erosca@de.adit-jv.com Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_debug_info and asoc_simple_debug_dai must be static
otherwise we might a compilation error if the compiler decides
not to inline the given function.
Hans de Goede [Sat, 5 Oct 2019 21:22:02 +0000 (23:22 +0200)]
ASoC: core: Fix pcm code debugfs error
We can have 2 dcpm-s with the same backend and frontend name
(capture + playback pair), this causes the following debugfs error
on Intel Bay Trail systems:
Robin Murphy [Wed, 2 Oct 2019 15:30:37 +0000 (16:30 +0100)]
ASoc: rockchip: i2s: Fix RPM imbalance
If rockchip_pcm_platform_register() fails, e.g. upon deferring to wait
for an absent DMA channel, we return without disabling RPM, which makes
subsequent re-probe attempts scream with errors about the unbalanced
enable. Don't do that.
ASoC: wm_adsp: Don't generate kcontrols without READ flags
User space always expects to be able to read ALSA controls, so ensure
no kcontrols are generated without an appropriate READ flag. In the case
of a read of such a control zeros will be returned.
ASoC: intel: sof_rt5682: add remove function to disable jack
When removing sof module the rt5682 jack handler will oops
if jack detection is not disabled. So add remove function,
which disables the jack detection.
ASoC: SOF: Intel: hda: Disable DMI L1 entry during capture
There is a known issue on some Intel platforms which causes
pause/release to run into xrun's during capture usecases.
The suggested workaround to address the issue is to
disable the entry of lower power L1 state in the physical
DMI link when there is a capture stream open.
Kai Vehmanen [Fri, 27 Sep 2019 20:05:35 +0000 (15:05 -0500)]
ASoC: SOF: Intel: hda: fix warnings during FW load
The "snd_pcm_substream" handle was not initialized properly
in hda-loader.c for firmware load.
When the HDA DMAs were used to load the firmware,
the interrupts related to firmware load also triggered
calls to snd_sof_pcm_period_elapsed() on a non-existent ALSA
PCM stream.
This caused runtime kernel warnings from
pcm_lib.c:snd_pcm_period_elapsed().
Pan Xiuli [Fri, 27 Sep 2019 20:05:31 +0000 (15:05 -0500)]
ASoC: SOF: pcm: harden PCM STOP sequence
The old STOP sequence is: 1. stop DMA 2. send STOP ipc
If delay happen before the steps 1 and 2, the DMA buffer will be empty in
short time and cause pipeline xrun then stop the pipeline.
Then the step 2 ipc stop will return error as pipeline is already stopped.
Suggested change to avoid the issue is to switch the order of steps 1 and 2
for the stop sequence.
Kai Vehmanen [Fri, 27 Sep 2019 20:05:30 +0000 (15:05 -0500)]
ASoC: SOF: pcm: fix resource leak in hw_free
Fix a bug in sof_pcm_hw_free() where some cleanup actions were
skipped if STREAM_PCM_FREE IPC was already successfully sent to
DSP when the stream was stopped or suspended. This is incorrect
as hw_free should clean up also other resources, including pcm
lib page allocations, period elapsed work queue and call to
platform hw_free.
Fixes: c29d96c3b9b4 ("ASoC: SOF: reset DMA state in prepare") Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190927200538.660-6-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
We are using sof_parse_word_tokens() to parse tokens with
bool/byte/short/word tuple types, here add the missing check, to fix the
parsing failure at byte/bool tuple types.
ASoC: SOF: loader: fix kernel oops on firmware boot failure
When we fail to boot the firmware, we encounter a kernel oops in
hda_dsp_get_registers(), which is called conditionally in
hda_dsp_dump() when the sdev_>boot_complete flag is set.
Setting this flag _after_ dumping the data fixes the issue and does
not change the programming flow.
Li Xu [Tue, 1 Oct 2019 13:09:11 +0000 (14:09 +0100)]
ASoC: wm_adsp: Fix theoretical NULL pointer for alg_region
Fix potential NULL pointer dereference for alg_region in
wm_adsp_buffer_parse_legacy. In practice this can never happen as
loading the firmware should have failed at the wm_adsp2_setup_algs
stage, however probably better for the code to be robust against
future changes and this is more helpful for static analysis.
ASoC: wm8994: Do not register inapplicable controls for WM1811
In case of WM1811 device there are currently being registered controls
referring to registers not existing on that device.
It has been noticed when getting values of "AIF1ADC2 Volume", "AIF1DAC2
Volume" controls was failing during ALSA state restoring at boot time:
"amixer: Mixer hw:0 load error: Device or resource busy"
Reading some registers through I2C was failing with EBUSY error and
indeed these registers were not available according to the datasheet.
To fix this controls not available on WM1811 are moved to a separate
array and registered only for WM8994 and WM8958.
There are some further differences between WM8994 and WM1811,
e.g. registers 603h, 604h, 605h, which are not covered in this patch.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Link: https://lore.kernel.org/r/20190920130218.32690-2-s.nawrocki@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: samsung: arndale: Add missing OF node dereferencing
Ensure there is no OF node references kept when the driver
is removed/unbound.
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20190920130218.32690-3-s.nawrocki@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_DM365_VOICE_CODEC is a 'bool' option in a choice statement,
meaning it cannot be set to =m, but it selects two other drivers
that we may want to be loadable modules after all:
WARNING: unmet direct dependencies detected for SND_SOC_CQ0093VC
Depends on [m]: SOUND [=m] && !UML && SND [=m] && SND_SOC [=m]
Selected by [y]:
- SND_SOC_DM365_VOICE_CODEC [=y] && <choice>
Selected by [m]:
- SND_SOC_ALL_CODECS [=m] && SOUND [=m] && !UML && SND [=m] && SND_SOC [=m] && COMPILE_TEST [=y]
Add an intermediate symbol that sets SND_SOC_CQ0093VC and
MFD_DAVINCI_VOICECODEC to =m if SND_SOC=m.
ASoC: core: use list_del_init and move it back to soc_cleanup_component
commit afa85fa6dd0e ("ASoC: core: delete component->card_list in soc_remove_component only")
was trying to fix a kernel oops when list_del was called twice without
re-init the list. Use list_del_init() can solve it, too. Besides, it
will be more readable if we cleanup all component related resource at
soc_cleanup_component().
A potential bug was reported in the email "[BUG] atmel_ssc_dai: a
possible sleep-in-atomic bug in atmel_ssc_shutdown"[1]
Indeed in the function atmel_ssc_shutdown() free_irq() was called in a
critical section protected by spinlock.
However this spinlock is only used in atmel_ssc_shutdown() and
atmel_ssc_startup() functions. After further analysis, it occurred that
the call to these function are already protected by mutex used on the
calling functions.
Then we can remove the spinlock which will fix this bug as a side
effect. Thanks to this patch the following message disappears:
"BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:909"
ASoC: core: delete component->card_list in soc_remove_component only
We add component->card_list in the end of soc_probe_component(). In
other words, component->card_list will not be added if there is an
error in the soc_probe_component() function. So we can't delete
component->card_list in the error handling of soc_probe_component().
Fixes: af11717a09e0 ("ASoC: soc-core: add soc_cleanup_component()") Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190916210353.6318-1-yung-chuan.liao@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Viorel Suman [Fri, 30 Aug 2019 21:59:10 +0000 (00:59 +0300)]
ASoC: fsl_sai: Implement set_bclk_ratio
This is to allow machine drivers to set a certain bitclk rate
which might not be exactly rate * frame size.
Cc: NXP Linux Team <linux-imx@nxp.com> Signed-off-by: Viorel Suman <viorel.suman@nxp.com> Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com> Acked-by: Nicolin Chen <nicoleotsuka@gmail.com> Link: https://lore.kernel.org/r/20190830215910.31590-1-daniel.baluta@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org>
Ben Zhang [Fri, 6 Sep 2019 19:46:24 +0000 (12:46 -0700)]
ASoC: rt5677: keep analog power register at SND_SOC_BIAS_OFF
Instead of clearing RT5677_PWR_ANLG2 (MX-64h) to 0 at SND_SOC_BIAS_OFF,
we only clear the RT5677_PWR_CORE bit which is set at SND_SOC_BIAS_PREPARE.
MICBIAS control bits are left unchanged.
This fixed the bug where if MICBIAS1 widget is forced on, MICBIAS
control bits will be cleared at suspend and never turned back on again,
since DAPM thinks the widget is always on.
In order to simplify understanding what register values are being
written to the codec for debugging more advanced features (such as
hotwording) it is best to remove magic numbers
soc_unbind_aux_dev() itself is not related to remove_order (1).
And, it is called from soc_remove_aux_devices(), even though
its paired function soc_bind_aux_dev() is called from
snd_soc_instantiate_card().
It is very unbalance, and very difficult to understand.
This patch do
1) update soc_bind_aux_dev() to self contained
2) call it from soc_cleanup_card_resources() to make up balance
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
soc-core.c has soc_bind_aux_dev(), but, there is no its paired
soc_unbind_aux_dev().
This patch adds soc_unbind_aux_dev().
ASoC: soc-core: move soc_probe_link_dais() next to soc_remove_link_dais()
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
This patch moves soc_probe_link_dais() next to soc_remove_link_dais()
which is paired function.
Current soc_probe_link_dais() (1) is called under probe_order (2),
and it will initialize dai_link related settings at *Last* turn (3)(B).
It is very complex code.
static int soc_probe_link_dais(..., order)
{
(A) /* probe DAIs here */
...
(3) if (order != SND_SOC_COMP_ORDER_LAST)
return 0;
(B) /* initialize dai_link related settings */
...
}
static int snd_soc_instantiate_card(...)
{
...
(2) for_each_comp_order(order) {
for_each_card_rtds(...) {
(1) ret = soc_probe_link_dais(..., order);
}
}
}
This patch separes soc_probe_link_dais() into "DAI probe" portion (A),
and dai_link settings portion (B).
The later is named as soc_link_init() by this patch.
ASoC: soc-core: move soc_probe_dai() next to soc_remove_dai()
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
This patch moves soc_probe_dai() next to soc_remove_dai() which is
paired function.
SoC: simple-card-utils: set 0Hz to sysclk when shutdown
This patch set 0Hz to sysclk when shutdown the card.
Some codecs set rate constraints that derives from sysclk. This
mechanism works correctly if machine drivers give fixed frequency.
But simple-audio and audio-graph card set variable clock rate if
'mclk-fs' property exists. In this case, rate constraints will go
bad scenario. For example a codec accepts three limited rates
(mclk / 256, mclk / 384, mclk / 512).
Bad scenario as follows (mclk-fs = 256):
- Initialize sysclk by correct value (Ex. 12.288MHz)
- Codec set constraints of PCM rate by sysclk
48kHz (1/256), 32kHz (1/384), 24kHz (1/512)
- Play 48kHz sound, it's acceptable
- Sysclk is not changed
- Play 32kHz sound, it's acceptable
- Set sysclk to 8.192MHz (= fs * mclk-fs = 32k * 256)
- Codec set constraints of PCM rate by sysclk
32kHz (1/256), 21.33kHz (1/384), 16kHz (1/512)
- Play 48kHz again, but it's NOT acceptable because constraints
do not allow 48kHz
So codecs treat 0Hz sysclk as signal of applying no constraints to
avoid this problem.
Some codecs treat 0Hz sysclk as signal of applying no constraints.
This driver does not have such feature but current implementation
outputs 'Failed to set mclk' error message if machine driver sets
0Hz sysclk to this driver.
ASoC: es8316: support fixed and variable both clock rates
This patch supports some type of machine drivers that set 0 to mclk
when sound device goes to idle state. After applied this patch,
sysclk == 0 means there is no constraint of sound rate and other
values will set constraints which is derived by sysclk setting.
Original code refuses sysclk == 0 setting. But some boards and SoC
(such as RockPro64 and RockChip I2S) has connected SoC MCLK out to
ES8316 MCLK in. In this case, SoC side I2S will choose suitable
frequency of MCLK such as fs * mclk-fs when user starts playing or
capturing.
Bad scenario as follows (mclk-fs = 256):
- Initialize sysclk by correct value (Ex. 12.288MHz)
- ES8316 set constraints of PCM rate by sysclk
48kHz (1/256), 32kHz (1/384), 30.720kHz (1/400),
24kHz (1/512), 16kHz (1/768), 12kHz (1/1024)
- Play 48kHz sound, it's acceptable
- Sysclk is not changed
- Play 32kHz sound, it's acceptable
- Set sysclk by 8.192MHz (= fs * mclk-fs = 32k * 256)
- ES8316 set constraints of PCM rate by sysclk
32kHz (1/256), 21.33kHz (1/384), 20.48kHz (1/400),
16kHz (1/512), 10.66kHz (1/768), 8kHz (1/1024)
- Play 48kHz again, but it's NOT acceptable because constraints
list does not allow 48kHz
When do compile test, if SND_SOC_SOF_OF is not set, we get:
sound/soc/sof/imx/imx8.o: In function `imx8_dsp_handle_request':
imx8.c:(.text+0xb0): undefined reference to `snd_sof_ipc_msgs_rx'
sound/soc/sof/imx/imx8.o: In function `imx8_ipc_msg_data':
imx8.c:(.text+0xf4): undefined reference to `sof_mailbox_read'
sound/soc/sof/imx/imx8.o: In function `imx8_dsp_handle_reply':
imx8.c:(.text+0x160): undefined reference to `sof_mailbox_read'
Make SND_SOC_SOF_IMX_TOPLEVEL always depends on SND_SOC_SOF_OF
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: f8612cb94e5f ("ASoC: SOF: imx: Add i.MX8 HW support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190905064400.24800-1-yuehaibing@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org>
The TODDR component, as it, has a maximum of 8 input. Depending on
the SoC, these may not all be connected or some input components may
not be supported
Instead of decribing only the connected inputs, describe them all
and let ASoC routing do the rest.
The g12a audio subsystem, which is a derivative of the axg subsystem,
provides a dedicated reset line for each of the audio components.
The axg did not provide that and it is unclear if/when these reset are
required. The reset already helped solve a channel mapping issue on the
tdm formatter devices. Let's add the reset binding for the other
components, so we can describe this in DT. We'll use it later on
in the driver when/if needed.
ASoC: qcom: common: Include link-name in error messages
Reading out the link-name earlier and including it in the various error
messages makes it much more convenient to figure out what links have
unmet dependencies.
ASoC: soc-core: add comment to jack at soc_remove_component()
Basically, driver which setups snd_soc_component_set_jack() need
to release it by themselves. But, as framework level robustness,
soc_remove_component() also releases it.
To avoid code reader confuse, this patch makes it clarify.
This patch introduce clock property for MCLK master freq control.
Driver will set rate of MCLK master if set_sysclk is called and
changing sysclk by board driver.
[Modified slightly to apply without an earlier patch in the series due
to context diffs -- broonie]
ALSA SoC try to rebind Sound Card if Card/CPU/Codec/Platform
were unbinded and re-binded again.
But, Audio Graph Card might can't rebind again if user do for example
unbind CPU or Codec driver
bind CPU or Codec driver
Because Audio Graph Card is still pointing old/unbinded
CPU or Codec driver's DAI name at dlc->dai_name.
To avoid this issue, it needs to alloc memory and keep DAI name
even though if CPU or Codec driver was unbinded.
Or, always do unbind/bind at Sound Card.
For now, this patch indicates this issue as FIXME.
ALSA SoC try to rebind Sound Card if Card/CPU/Codec/Platform
were unbinded and re-binded again.
But, Simple Card might can't rebind again if user do for example
unbind CPU or Codec driver
bind CPU or Codec driver
Because Simple Card is still pointing old/unbinded
CPU or Codec driver's DAI name at dlc->dai_name.
To avoid this issue, it needs to alloc memory and keep DAI name
even though if CPU or Codec driver was unbinded.
Or, always do unbind/bind at Sound Card.
For now, this patch indicates this issue as FIXME.
ASoC: soc-core: move soc_probe_link_components() position
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
soc_probe_link_components() has paired soc_remove_link_components(),
but, these are implemented at different place.
So it is difficult to confirm code.
This patch moves soc_probe_link_components() next to
soc_remove_link_components().
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
soc-dapm has snd_soc_dapm_free() which cleanups debugfs, widgets, list.
But, there is no paired initialize function.
This patch adds snd_soc_dapm_init() and initilaizing dapm
Current ASoC setups some dapm related member at
snd_soc_component_initialize() which is called when component was
registered, and setups remaining member at soc_probe_component()
which is called when component was probed.
This kind of setup separation is no meanings, and it is very
difficult to read and confusable.
This patch setups all dapm settings at one place.
ASoC: soc-core: move soc_probe_component() position
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
soc_probe_comonent() has paired soc_remove_comonent(),
but, these are implemented at different place.
So it is difficult to confirm code.
This patch moves soc_probe_component() next to
soc_remove_component().
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
soc_rtd_init() was soc_post_component_init(), but there was no
its paired soc_post_component_free(), but it is done at
soc_remove_link_dais().
This means it is difficult to find related code.
This patch adds soc_rtd_free() which is paired soc_rtd_init().
soc_rtd_xxx() will be more cleanuped in the future.
Maxime Ripard [Wed, 28 Aug 2019 12:52:09 +0000 (14:52 +0200)]
ASoC: dt-bindings: Convert Allwinner A64 analog codec to a schema
The Allwinner A64 SoC has an embedded audio codec that uses a separate
controller to drive its analog part, which is supported in Linux, with a
matching Device Tree binding.
Now that we have the DT validation in place, let's convert the device tree
bindings for that controller over to a YAML schemas.
Even though the H6 compatible has been properly added, the exeption for the
number of DMA channels hasn't been updated, leading in a validation
warning.
Fix this.
Fixes: f03fc08a0adc ("dt-bindings: sound: sun4i-spdif: Add Allwinner H6 compatible") Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Link: https://lore.kernel.org/r/20190828125209.28173-1-mripard@kernel.org Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
We should only select SND_INTEL_NHLT when ACPI is defined. This was
done for the legacy HDAudio driver but not for DSP-enabled cases,
leading to compilation errors with randconfig.
Fix by aligning on the same solution.
For the Skylake driver this is overkill since there is a top-level
dependency on ACPI, but it doesn't hurt and it's better to have
consistency.
Fixes: 67aa344f79736 ('ASoC: SOF: Intel: hda: fixup HDaudio topology name with DMIC number') Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20190829214213.11653-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Apart from Haswell machines, all other devices have their private data
set to snd_soc_acpi_mach instance.
Changes for HSW/ BDW boards introduced with series:
https://patchwork.kernel.org/cover/10782035/
added support for dai_link platform_name adjustments within card probe
routines. These take for granted private_data points to
snd_soc_acpi_mach whereas for Haswell, it's sst_pdata instead. Change
private context of platform_device - representing machine board - to
address this.
Fixes: e736e6d6936d ("ASoC: Intel: haswell: platform name fixup support") Fixes: f211bee40848 ("ASoC: Intel: bdw-rt5677: platform name fixup support") Fixes: 958631599dd0 ("ASoC: Intel: broadwell: platform name fixup support") Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com> Link: https://lore.kernel.org/r/20190822113616.22702-2-cezary.rojewski@intel.com Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Fri, 30 Aug 2019 10:38:40 +0000 (13:38 +0300)]
ASoC: ti: edma-pcm: Fix for legacy dma_slave_map based channel lookup
Most of the daVinci devices does not boot with DT. In this case the DMA
channel is looked up with dma_slave_map and for that the chan_names[]
must be configured.
Both McASP and ASP/McBSP uses "tx" and "rx" as channel names, so we can
just do this when the dev->of_node is not valid.
Peter Ujfalusi [Fri, 30 Aug 2019 10:38:38 +0000 (13:38 +0300)]
ASoC: ti: davinci-i2s: Add S32_LE as support format
ASP/McBSP can support 8/16/20/24/32 bits word in theory. I have only tested
S16_LE and S32_LE, the other formats might not work so only extend the
supported formats with S32_LE for now.
ALSA: pcm: add support for 352.8KHz and 384KHz sample rate
Most of the modern codecs supports 352.8KHz and 384KHz sample rates.
Currenlty HW params fails to set 352.8Kz and 384KHz sample rate
as these are not in known rates list.
Add these new rates to known list to allow them.
This patch also adds defines in pcm.h so that drivers can use it.
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org> Signed-off-by: Banajit Goswami <bgoswami@codeaurora.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20190822095653.7200-2-srinivas.kandagatla@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org>
Michał Mirosław [Sat, 24 Aug 2019 20:26:53 +0000 (22:26 +0200)]
ASoC: atmel_ssc_dai: rework DAI format configuration
Rework DAI format calculation in preparation for adding more formats
later. As a side-effect this enables all CBM/CBS x CFM/CFS combinations
for supported formats. (Note: the additional modes are not tested.)
Note: this changes FSEDGE to POSITIVE for I2S CBM_CFS mode as the TXSYN
interrupt is not used anyway.
projects / kernel.git / log