Stefan Roese [Thu, 3 Dec 2015 11:39:45 +0000 (12:39 +0100)]
arm: mvebu: Don't call arch_cpu_init() from SPL at all
This patch removes the call to arch_cpu_init() in the SPL U-Boot version.
As SPL does not need all the configuration done in this function. And
also does not need the reconfiguration of the internal register
address to 0xf1000000. This will be done by the main U-Boot later on.
This also fixes a problem with the timer not beeing initialized on AXP,
as needed for the mdelay in the setup_usb_phys(). This will now only
be called once in main U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
Stefan Roese [Mon, 14 Dec 2015 11:31:48 +0000 (12:31 +0100)]
arm: mvebu: Add v7_outer_cache_disable function for AXP & A38x
Add functionality to correctly disable the L2 cache on the Armada XP
and 38x platforms.
Without this, booting into Linux on ClearFog (A38x) results in a hangup
without any output on the serial console at all. Even with earlyprintk
enabled.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
Stefan Roese [Thu, 3 Dec 2015 11:39:45 +0000 (12:39 +0100)]
arm: mvebu: Enable L2 cache on Armada XP
Until now, the L2 cache was never enabled again in U-Boot. To get
even better performance (bootup time), lets enable the L2 cache
in U-Boot. This code was taken from the Linux kernel.
A performance gain was measured on the DB-MV784MP-GP board by testing
with tftpboot and sata commands.
This patch also cleans up the L2 cache related code. And makes sure that
the L2 cache is only disabled once.
Please note that A38x still runs with L2 cache disabled. And needs
to be enabled for this SoC in a separate patch if needed or desired.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
Stefan Roese [Thu, 3 Dec 2015 11:39:45 +0000 (12:39 +0100)]
arm: mvebu: db-mv784mp-gp: Switch from IDE to SATA support
Enable the newly introduced SATA driver for the Marvell AXP with DMA
support instead of the PIO-only IDE driver. This increases the
transfer speed. And is also more in-line with the Armada 38x
ports, which also use a SATA driver (AHCI) and the "sata" U-Boot
commands.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
Tor Krill [Thu, 3 Dec 2015 11:38:02 +0000 (12:38 +0100)]
sata: Add SATA driver with DMA support for Marvell Kirkwood and Armada XP
This patch adds a new SATA driver for the Marvell Kirkwood and Armada
370 / XP SoC's.
This driver supports the SATA controller of some Mavell SoC's.
Here a (most likely incomplete) list of the supported SoC's:
- Kirkwood
- Armada 370
- Armada XP
This driver implementation is an alternative to the already available
driver via the "ide" commands interface (drivers/block/mvsata_ide.c).
But this driver only supports PIO mode and as this new driver also
supports transfer via DMA, its much faster.
Please note, that the newer SoC's (e.g. Armada 38x) are not supported
by this driver. As they have an AHCI compatible SATA controller
integrated.
The original version of this driver was sent by Tor Krill to the U-Boot
list a few years ago. Here the link:
Changes by Stefan:
- Coding-style cleanup
- Support for Armada XP added
- MBUS window setup added
- D-cache flush and invalidation added - works with dcache enabled on
Armada XP
- Removed mdelay() from ata_wait_register() and add timer based timeout
detection to speed up the transfer
Signed-off-by: Tor Krill <tor@excito.com> Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Tom Rini <trini@konsulko.com>
Stefan Roese [Tue, 20 Oct 2015 13:14:47 +0000 (15:14 +0200)]
arm: mvebu: Add SolidRun ClearFog Armada 38x initial support
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Rabeeh Khoury <rabeeh@solid-run.com> Cc: Luka Perkov <luka.perkov@sartura.hr>
Stefan Roese [Thu, 19 Nov 2015 06:46:15 +0000 (07:46 +0100)]
net: mvneta: Convert to driver model
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Simon Glass <sjg@chromium.org>
Stefan Roese [Thu, 19 Nov 2015 10:03:25 +0000 (11:03 +0100)]
arm: mvebu: Add armada-xp-maxbcm.dts for maxbcm board
This is needed for the upcoming ethernet DM conversion of the maxbcm
board. The configuration of the PHY is then extracted from the DT
instead of using the defines from the config header.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
Stefan Roese [Fri, 20 Nov 2015 12:51:57 +0000 (13:51 +0100)]
arm: mvebu: Add SPI driver model support
This patch enables the DM support for the SPI driver and the
SPI NOR flash chips. Some MVEBU boards boot from SPI NOR, so
adding the aliases and enabling CONFIG_DM_SEQ_ALIAS is needed
here.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 20 Nov 2015 12:39:43 +0000 (13:39 +0100)]
spi: kirkwood_spi.c: Add driver model support
This patch adds driver model support to the kirkwood SPI driver. Which
is also used on the MVEBU SoC's, now being converted to DM. Non-DM
support is still available for the "older" platforms using this
driver, like kirkwood.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org>
Stefan Roese [Fri, 20 Nov 2015 07:44:21 +0000 (08:44 +0100)]
spi: kirkwood_spi.c: Prepare for driver model support
This patch prepares the Kirkwood SPI driver, also used on the MVEBU board
(Armada XP / 38x), for the conversion to driver model.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org>
Stefan Roese [Wed, 25 Nov 2015 06:37:00 +0000 (07:37 +0100)]
arm: mvebu: Add DM and OF_CONTROL support to SPL
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Simon Glass <sjg@chromium.org>
Stefan Roese [Thu, 19 Nov 2015 12:50:10 +0000 (13:50 +0100)]
arm: mvebu: ddr: Fix compilation warning
gcc 5.1 generates this new warning (for Armada 38x platforms):
drivers/ddr/marvell/a38x/ddr3_debug.c: In function 'hws_ddr3_tip_read_training_result':
drivers/ddr/marvell/a38x/ddr3_debug.c:177:40: warning: 'sizeof' on array
function parameter 'result' will return size of 'enum hws_result (*)[1]' [-Wsizeof-array-argument]
memcpy(result, training_result, sizeof(result));
^
drivers/ddr/marvell/a38x/ddr3_debug.c:171:31: note: declared here
u32 dev_num, enum hws_result result[MAX_STAGE_LIMIT][MAX_INTERFACE_NUM])
^
Since this functions is not referenced anywhere, lets just remove it.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
Masahiro Yamada [Thu, 17 Dec 2015 08:19:35 +0000 (17:19 +0900)]
image: check "bootm_low" and "bootm_size" if "initrd_high" is missing
To boot Linux, we should prevent Initramdisk and FDT from going too
high.
Currently, boot_relocate_fdt() checks "fdt_high" environment first,
and then falls back to getenv_bootm_mapsize() + getenv_bootm_low()
if "fdt_high" is missing.
On the other hand, boot_ramdisk_high() only checks "initrd_high" to
get the address limit for the Initramdisk. We also want to let this
case fall back to getenv_bootm_mapsize() + getenv_bootm_low().
Mugunthan V N [Wed, 23 Dec 2015 15:09:36 +0000 (20:39 +0530)]
dm: core: Add a new api to get indexed device address
Add new api to get device address based on index.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Jagan Teki <jteki@openedev.com>
[Rebased on master] Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Tue, 5 Jan 2016 08:14:26 +0000 (13:44 +0530)]
power: pmic.h: Drop include <spi.h>
include/power/pmic.h never used any generic spi code
from include/spi.h, but this has been added in below commit.
"dm: pmic: add implementation of driver model pmic uclass"
(sha1: 4d9057e82be11a862db411c4867e859fe0d4ca2a)
Adding functionalities in include/spi.h will trigger a build
issue as this been added used in include/power/pmic.h
Build issue on trats2 with adding BIT macro on spi.h:
----------------------------------------------------
CC lib/asm-offsets.s
In file included from include/power/pmic.h:15:0,
from include/power/max77686_pmic.h:11,
from include/configs/trats2.h:212,
from include/config.h:5,
from include/common.h:18,
from lib/asm-offsets.c:15:
include/spi.h: In function 'spi_w8r8':
include/spi.h:327:2: warning: implicit declaration of function 'BIT' [-Wimplicit-function-declaration]
Cc: Simon Glass <sjg@chromium.org> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Simon Glass <sjg@chromium.org>
Mugunthan V N [Wed, 23 Dec 2015 15:09:49 +0000 (20:39 +0530)]
defconfig: am437x_sk_evm: enable spi driver model
enable spi driver model for am437x_sk_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:46 +0000 (20:39 +0530)]
defconfig: dra74_evm: enable spi driver model
enable spi driver model for dra74_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:45 +0000 (20:39 +0530)]
defconfig: dra72_evm: enable spi driver model
enable mmc driver model for dra72_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:40 +0000 (20:39 +0530)]
drivers: spi: ti_qspi: convert driver to adopt device driver model
adopt ti_qspi driver to device driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:37 +0000 (20:39 +0530)]
spi: Add support for dual and quad mode
spi bus can support dual and quad wire data transfers for tx and
rx. So defining dual and quad modes for both tx and rx. Also add
support to parse bus width used for spi tx and rx transfers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:34 +0000 (20:39 +0530)]
drivers: spi:ti_qspi: change ti_qspi_slave to ti_qspi_priv for driver model conversion
Changing the ti_qspi_priv structure and its instance names from
to priv for driver mode conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:33 +0000 (20:39 +0530)]
drivers: spi: ti_qspi: do not hard code chip select for memory map configuration
To enable memory map in dra7xx, specific chip select must be
written to control module register. But this hard coded to chip
select 1, fixing it by writing the specific chip select value to
control module register.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 28 Dec 2015 17:25:50 +0000 (22:55 +0530)]
spi: Add SPI_TX_DUAL mode
Added SPI_TX_DUAL mode flag.
Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Tue, 29 Dec 2015 06:42:30 +0000 (12:12 +0530)]
spi: Minor cleanup
- Add comments on mode_rx
- Tab space's
Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 28 Dec 2015 16:54:08 +0000 (22:24 +0530)]
spi: Use BIT macro
Used BIT macro like 1 << nr as BIT(nr) where nr is 0...n
Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 10:21:06 +0000 (15:51 +0530)]
spi: Fix bit assignment with flags
Fixed bit assignment with flags members on spi_slave{}
Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 28 Dec 2015 16:53:14 +0000 (22:23 +0530)]
spi: Move flags macro's to spi_slave{} members
This patch moves flags macro's to respective member
position on spi_slave{}, for better readabilty and
finding the respective member macro's easily.
Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 09:54:24 +0000 (15:24 +0530)]
spi: Rename op_mode_rx to mode_rx
Since spi rx mode macro's are renamed to simple and
meaninfull, this patch will rename the respective
structure members.
Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 09:31:23 +0000 (15:01 +0530)]
spi: Remove SPI_OPM_RX_DIO|QIOF
SPI_OPM_RX_DIO and SPI_OPM_RX_QIOF are rx IO
commands/opmodes for dual and quad. Usually IO
operation's are referred to flash protocol rather
with spi controller protocol, these are still present
in flash side for the usage of spi-nor controllers.
Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 09:23:59 +0000 (14:53 +0530)]
spi: Remove SPI_OPM_RX_EXTN
SPI_OPM_RX_EXTN is a combination of all rx opmode's
and spi driver shall use any one of the rx mode at
a time not the combination and it is true in case of
flash where spi_flash_table mention combination of
supported read opmodes so-that the required one
will pick based on the rx mode from spi driver.
Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 08:18:08 +0000 (13:48 +0530)]
sf: Write quad bit along with read status
While setting quad bit on spansion, macronix code
is writing only particular quad bit this may give
wrong functionality with other register bits,
So this patch fix the issue where it with write
previous read reg status along particular quad bit.
Cc: Vignesh R <vigneshr@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Tue, 15 Dec 2015 07:12:02 +0000 (12:42 +0530)]
sf: Read back and check once macronix quad bit set
One macronix quad bit set using SR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Tue, 15 Dec 2015 06:58:39 +0000 (12:28 +0530)]
sf: Read back and check once spansion quad bit set
One spansion quad bit set using CR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 14 Dec 2015 12:45:39 +0000 (18:15 +0530)]
sf: Fix quad bit set for micron devices
Setting up quad bit for micron devices need to do the
same way as other flash devices like spansion, winbond
etc does using enhanced volatile config register so this
patch adds this support instead of printing "QEB is volatile"
Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Peter Pan <peterpandong@micron.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sun, 13 Dec 2015 14:40:33 +0000 (20:10 +0530)]
spi: Use mode instead of op_mode_tx
Used mode member from spi_slave{} instead of op_mode_tx.
Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 14 Dec 2015 06:45:17 +0000 (12:15 +0530)]
spi: make mode visible to both dm and non-dm
Couldn't find the exact reason to define 'mode' for dm,
probably it is not using in non-dm drivers but it need
to visible both dm and non-dm as mode data is getting
dereferred in spi flash core ie common to both.
Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sat, 12 Dec 2015 06:21:57 +0000 (11:51 +0530)]
sf: Get spi locally from spi_flash
For better code readabilty, get the spi pointer from
spi_flash{} locally and use it instead of direct
dereferring spi pinter as flash->spi->*
Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
Tom Rini [Tue, 8 Dec 2015 03:26:34 +0000 (22:26 -0500)]
sandbox: eth-raw-os.c: Ensure that our interface name is not too long
Coverity notes that we do not ensure when we copy ifname we still have
space left to ensure NULL termination. As cannot control the size of
ifr_name we must make sure that our argument will not overflow the
buffer.
Reported-by: Coverity (CID 131094) Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Mon, 14 Dec 2015 15:18:15 +0000 (16:18 +0100)]
dm: core: Add option to configure an offset for the address translation
Some platforms need to ability to configure an offset to the standard
addresses extracted from the device-tree. This patch allows this by
adding a function to DM to configure this offset (if needed).
Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Cc: Simon Glass <sjg@chromium.org>
Fixed space before tab: Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 14 Dec 2015 04:37:00 +0000 (21:37 -0700)]
rockchip: Use the debug UART on rk3036
Rather than using a new debug UART implementation, use the standard one
provided by U-Boot. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Simon Glass [Sun, 29 Nov 2015 20:18:10 +0000 (13:18 -0700)]
dm: net: usb: Refactor mcs7830 driver ready for DM conversion
Remove stamp data and create common functions for the main Ethernet
operations. This will make it easier to convert this driver to support
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 29 Nov 2015 20:18:09 +0000 (13:18 -0700)]
pci: Tidy up comments in pci_bind_bus_devices()
The current comments are confusing. We don't actually bind a generic device
when the device tree has no information. We try to scan available PCI
drivers. Update the comments to reflect this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:18:08 +0000 (13:18 -0700)]
dm: Convert PCI MMC over to use DM PCI API
At present pci_mmc_init() does not correctly use the PCI function since the
list it passes is not terminated. The array size passed to pci_mmc_init() is
actually not used correctly. Fix this and adjust the pci_mmc_init() to scan
all available MMC devices.
Adjust this code to use the new driver model PCI API.
This should move over to the new MMC uclass at some point.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:55 +0000 (13:17 -0700)]
dm: x86: ivybridge: Convert graphics init to use DM PCI API
Use the driver-model PCI functions here where possible. For now we have to
search for the device with pci_bus_find_bdf() but at some point we can put
this in a proper driver and avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:54 +0000 (13:17 -0700)]
dm: serial: Convert ns16550 driver to use driver model PCI API
Use the driver model version of the function to find the BAR. This updates
the fdtdec function, of which ns16550 is the only user.
The fdtdec_get_pci_bdf() function is dropped for several reasons:
- with driver model we should use 'struct udevice *' rather than passing the
device tree offset explicitly
- there are no other users in the tree
- the function parses for information which is already available in the PCI
device structure (specifically struct pci_child_platdata which is available
at dev_get_parent_platdata(dev)
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:49 +0000 (13:17 -0700)]
dm: pci: Use driver model PCI API in auto-config
At present we are using legacy functions even in the auto-configuration code
used by driver model. Add a new pci_auto.c version which uses the correct
API.
Create a new pci_internal.h header to hold functions that are used within
the PCI subsystem, but are not exported to other drivers.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:48 +0000 (13:17 -0700)]
dm: pci: Add a dm_ prefix to pci_bus_find_bdf()
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.
For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_bus_find_bdf() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:47 +0000 (13:17 -0700)]
dm: pci: Add a dm_ prefix to pci_get_bdf()
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.
For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_get_bdf() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Masahiro Yamada [Fri, 8 Jan 2016 16:51:16 +0000 (01:51 +0900)]
ARM: uniphier: fix recommended board setting in document
The mem_is_flash() in arch/arm/mach-uniphier/micro-support_card.c
writes/reads the tail of each NOR flash bank to check if the device
really resides there.
If CS1_SPLIT were enabled, the support card would always require two
NOR flash devices to be inserted for the correct NOR detection.
This is not probably what we want.
Masahiro Yamada [Fri, 8 Jan 2016 16:51:15 +0000 (01:51 +0900)]
ARM: uniphier: add dump command for DDR Multi PHY registers
The ProXstream2/PH1-LD6b is integrated with a new IP for DDR PHY
which is not register-compatible with the former SoCs.
Add a new command to support the register dump of this IP.
Masahiro Yamada [Fri, 8 Jan 2016 16:51:14 +0000 (01:51 +0900)]
ARM: uniphier: add DRAM init code for ProXstream2/PH1-LD6b
As mentioned in the log of commit 019df879a93e2 (ARM: uniphier: add
ProXstream2 and PH1-LD6b support), the DRAM init code was missing
for a long time. Finally, here it is. SPL works now.
projects / uboot.git / log