net/sched: act_ct: fix miss set mru for ovs after defrag in act_ct
When openvswitch conntrack offload with act_ct action. Fragment packets
defrag in the ingress tc act_ct action and miss the next chain. Then the
packet pass to the openvswitch datapath without the mru. The over
mtu packet will be dropped in output action in openvswitch for over mtu.
This patch add mru in the tc_skb_ext for adefrag and miss next chain
situation. And also add mru in the qdisc_skb_cb. The act_ct set the mru
to the qdisc_skb_cb when the packet defrag. And When the chain miss,
The mru is set to tc_skb_ext which can be got by ovs datapath.
Fixes: 1a23a38cf53c ("net/sched: Introduce action ct") Signed-off-by: wenxu <wenxu@ucloud.cn> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series is a result of trying to upstream a new device
tree for a TQMa7D based board[1][2]. Initial this DTS used some
deprecated PHY reset properties on the FEC device; NXP Ethernet
MAC also known as Freescale Fast Ethernet Controller.
When switching from FEC properties[3]:
"phy-reset-gpios"
"phy-reset-duration"
"phy-reset-post-delay"
To MDIO PHY properties[4]:
"reset-gpios"
"reset-assert-us"
"reset-deassert-us"
The result was that no Ethernet PHY device was detected on boot.
This issue could be worked around by disabling PHY type ID auto-
detection by using "ethernet-phy-id0022.1560" as compatible
string and not "ethernet-phy-ieee802.3-c22".
Upstreaming a DTS with this workaround was not accepted, so I
digged into the MDIO reset flow and found that it had a few
missing parts compared to the deprecated FEC reset function.
After some more testing and logic analyzer traces it was
revealed that the failed PHY communication was due to missing
initial device reset.
I was suggested[5] in a earlier mail thread to use MDIO bus
reset as that was performed before auto-detection, but current
device tree binding was limited to reset assert in usec.
Microchip/Micrel Ethernet PHYs recommended reset circuit[8],
figure 7-12, is a little "slow" after reset deassert as that
is left to a RC circuit with a tau of ~100ms; using a 10k PU
resistor together with a 10uF decoupling capacitor. The diode
in serie of the reset signal converts the GPIO push-pull output
into a open-drain output. So a post reset delay in the range
of 500-1000ms is needed, depending on component tolerances
and general hardware design margins.
In the first version of this patch series[6] I reused the
"reset-delay-us" property for reset deassert in usec as that
would cause 50/50% duty-cycle, but that would always apply.
The solution in this patch series is to add a new MDIO bus
property, so post reset delay is optional and configured
separately.
MDIO bus properties[7]:
"reset-delay-us"
"reset-post-delay-us" (new)
I have not marked this with "Fixes:" as no single commit is the
cause and historically this code has only supported MDIO devices
that need reset after auto-detection. The patch series also uses
a new flexible sleep helper function that was introduced in
5.8-rc1, so the driver uses the optimal sleep function depending
on value loaded from device tree.
Future work in this area could add new properties on the MDIO
device, so reset points are configurable, e.g. no reset,
before/after auto-detection or both.
Bruno Thomsen [Thu, 30 Jul 2020 19:57:49 +0000 (21:57 +0200)]
net: mdio device: use flexible sleeping in reset function
MDIO device reset assert and deassert length was created by
usleep_range() but that does not ensure optimal handling of
all the different values from device tree properties.
By switching to the new flexible sleeping helper function,
fsleep(), the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruno Thomsen [Thu, 30 Jul 2020 19:57:48 +0000 (21:57 +0200)]
net: mdiobus: add reset-post-delay-us handling
Load new "reset-post-delay-us" value from MDIO properties,
and if configured to a greater then zero delay do a
flexible sleeping delay after MDIO bus reset deassert.
This allows devices to exit reset state before start
bus communication.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bruno Thomsen [Thu, 30 Jul 2020 19:57:47 +0000 (21:57 +0200)]
net: mdiobus: use flexible sleeping for reset-delay-us
MDIO bus reset pulse width is created by using udelay()
and that function might not be optimal depending on
device tree value. By switching to the new fsleep() helper
the correct delay function is called depending on
delay length, e.g. udelay(), usleep_range() or msleep().
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add "reset-post-delay-us" parameter to MDIO bus properties,
so it's possible to add a delay after reset deassert.
This is optional in case external hardware slows down
release of the reset signal.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Encap offset calculation is incorrect in esp6, from Sabrina Dubroca.
2) Better parameter validation in pfkey_dump(), from Mark Salyzyn.
3) Fix several clang issues on powerpc in selftests, from Tanner Love.
4) cmsghdr_from_user_compat_to_kern() uses the wrong length, from Al
Viro.
5) Out of bounds access in mlx5e driver, from Raed Salem.
6) Fix transfer buffer memleak in lan78xx, from Johan Havold.
7) RCU fixups in rhashtable, from Herbert Xu.
8) Fix ipv6 nexthop refcnt leak, from Xiyu Yang.
9) vxlan FDB dump must be done under RCU, from Ido Schimmel.
10) Fix use after free in mlxsw, from Ido Schimmel.
11) Fix map leak in HASH_OF_MAPS bpf code, from Andrii Nakryiko.
12) Fix bug in mac80211 Tx ack status reporting, from Vasanthakumar
Thiagarajan.
13) Fix memory leaks in IPV6_ADDRFORM code, from Cong Wang.
14) Fix bpf program reference count leaks in mlx5 during
mlx5e_alloc_rq(), from Xin Xiong.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (86 commits)
vxlan: fix memleak of fdb
rds: Prevent kernel-infoleak in rds_notify_queue_get()
net/sched: The error lable position is corrected in ct_init_module
net/mlx5e: fix bpf_prog reference count leaks in mlx5e_alloc_rq
net/mlx5e: E-Switch, Specify flow_source for rule with no in_port
net/mlx5e: E-Switch, Add misc bit when misc fields changed for mirroring
net/mlx5e: CT: Support restore ipv6 tunnel
net: gemini: Fix missing clk_disable_unprepare() in error path of gemini_ethernet_port_probe()
ionic: unlock queue mutex in error path
atm: fix atm_dev refcnt leaks in atmtcp_remove_persistent
net: ethernet: mtk_eth_soc: fix MTU warnings
net: nixge: fix potential memory leak in nixge_probe()
devlink: ignore -EOPNOTSUPP errors on dumpit
rxrpc: Fix race between recvmsg and sendmsg on immediate call failure
MAINTAINERS: Replace Thor Thayer as Altera Triple Speed Ethernet maintainer
selftests/bpf: fix netdevsim trap_flow_action_cookie read
ipv6: fix memory leaks on IPV6_ADDRFORM path
net/bpfilter: Initialize pos in __bpfilter_process_sockopt
igb: reinit_locked() should be called with rtnl_lock
e1000e: continue to init PHY even when failed to disable ULP
...
Linus Torvalds [Sat, 1 Aug 2020 20:08:50 +0000 (13:08 -0700)]
Merge tag 'perf-tools-fixes-2020-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tooling fixes from Arnaldo Carvalho de Melo:
- Fix libtraceevent build with binutils 2.35
- Fix memory leak in process_dynamic_array_len in libtraceevent
- Fix 'perf test 68' zstd compression for s390
- Fix record failure when mixed with ARM SPE event
* tag 'perf-tools-fixes-2020-08-01' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
libtraceevent: Fix build with binutils 2.35
perf tools: Fix record failure when mixed with ARM SPE event
perf tests: Fix test 68 zstd compression for s390
tools lib traceevent: Fix memory leak in process_dynamic_array_len
kernel test robot says:
net/mptcp/syncookies.c: In function 'mptcp_join_cookie_init':
include/linux/kernel.h:47:38: warning: division by zero [-Wdiv-by-zero]
#define ARRAY_SIZE(arr) (sizeof(arr) / sizeof((arr)[0]) + __must_be_array(arr))
I forgot that spinock_t size is 0 on UP, so ARRAY_SIZE cannot be used.
Fixes: dbbc43de3bfb70 ("mptcp: enable JOIN requests even if cookies are in use") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Sat, 1 Aug 2020 07:07:50 +0000 (07:07 +0000)]
vxlan: fix memleak of fdb
When vxlan interface is deleted, all fdbs are deleted by vxlan_flush().
vxlan_flush() flushes fdbs but it doesn't delete fdb, which contains
all-zeros-mac because it is deleted by vxlan_uninit().
But vxlan_uninit() deletes only the fdb, which contains both all-zeros-mac
and default vni.
So, the fdb, which contains both all-zeros-mac and non-default vni
will not be deleted.
Test commands:
ip link add vxlan0 type vxlan dstport 4789 external
ip link set vxlan0 up
bridge fdb add to 00:00:00:00:00:00 dst 172.0.0.1 dev vxlan0 via lo \
src_vni 10000 self permanent
ip link del vxlan0
Fixes: 7d44fd599ad5 ("vxlan: support fdb and learning in COLLECT_METADATA mode") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Brian Vazquez [Sat, 1 Aug 2020 03:01:10 +0000 (20:01 -0700)]
fib: fix another fib_rules_ops indirect call wrapper problem
It turns out that on commit a8046f06b782 ("fib: fix fib_rules_ops
indirect calls wrappers") I forgot to include the case when
CONFIG_IP_MULTIPLE_TABLES is not set.
Fixes: a8046f06b782 ("fib: fix fib_rules_ops indirect calls wrappers") Reported-by: Randy Dunlap <rdunlap@infradead.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Brian Vazquez <brianvv@google.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 1 Aug 2020 02:09:29 +0000 (19:09 -0700)]
tcp: fix build fong CONFIG_MPTCP=n
Fixes these errors:
net/ipv4/syncookies.c: In function 'tcp_get_cookie_sock':
net/ipv4/syncookies.c:216:19: error: 'struct tcp_request_sock' has no
member named 'drop_req'
216 | if (tcp_rsk(req)->drop_req) {
| ^~
net/ipv4/syncookies.c: In function 'cookie_tcp_reqsk_alloc':
net/ipv4/syncookies.c:289:27: warning: unused variable 'treq'
[-Wunused-variable]
289 | struct tcp_request_sock *treq;
| ^~~~
make[3]: *** [scripts/Makefile.build:280: net/ipv4/syncookies.o] Error 1
make[3]: *** Waiting for unfinished jobs....
Fixes: dbbc43de3bfb ("mptcp: enable JOIN requests even if cookies are in use") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 1 Aug 2020 17:11:42 +0000 (10:11 -0700)]
Merge tag 'pinctrl-v5.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"A single last minute pin control fix to the Qualcomm driver fixing
missing dual edge PCH interrupts"
* tag 'pinctrl-v5.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: Handle broken/missing PDC dual edge IRQs on sc7180
David S. Miller [Sat, 1 Aug 2020 01:51:40 +0000 (18:51 -0700)]
Merge tag 'mac80211-next-for-davem-2020-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes
* code cleanups and fixups as usual
* AQL & internal TXQ improvements from Felix
* some mesh 802.1X support bits
* some injection improvements from Mathy of KRACK
fame, so we'll see what this results in ;-)
* some more initial S1G supports bits, this time
(some of?) the userspace APIs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Sat, 1 Aug 2020 00:34:01 +0000 (17:34 -0700)]
rtnetlink: add support for protodown reason
netdev protodown is a mechanism that allows protocols to
hold an interface down. It was initially introduced in
the kernel to hold links down by a multihoming protocol.
There was also an attempt to introduce protodown
reason at the time but was rejected. protodown and protodown reason
is supported by almost every switching and routing platform.
It was ok for a while to live without a protodown reason.
But, its become more critical now given more than
one protocol may need to keep a link down on a system
at the same time. eg: vrrp peer node, port security,
multihoming protocol. Its common for Network operators and
protocol developers to look for such a reason on a networking
box (Its also known as errDisable by most networking operators)
This patch adds support for link protodown reason
attribute. There are two ways to maintain protodown
reasons.
(a) enumerate every possible reason code in kernel
- A protocol developer has to make a request and
have that appear in a certain kernel version
(b) provide the bits in the kernel, and allow user-space
(sysadmin or NOS distributions) to manage the bit-to-reasonname
map.
- This makes extending reason codes easier (kind of like
the iproute2 table to vrf-name map /etc/iproute2/rt_tables.d/)
This patch takes approach (b).
a few things about the patch:
- It treats the protodown reason bits as counter to indicate
active protodown users
- Since protodown attribute is already an exposed UAPI,
the reason is not enforced on a protodown set. Its a no-op
if not used.
the patch follows the below algorithm:
- presence of reason bits set indicates protodown
is in use
- user can set protodown and protodown reason in a
single or multiple setlink operations
- setlink operation to clear protodown, will return -EBUSY
if there are active protodown reason bits
- reason is not included in link dumps if not used
example with patched iproute2:
$cat /etc/iproute2/protodown_reasons.d/r.conf
0 mlag
1 evpn
2 vrrp
3 psecurity
$ip link set dev vxlan0 protodown on protodown_reason vrrp on
$ip link set dev vxlan0 protodown_reason mlag on
$ip link show
14: vxlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether f6:06:be:17:91:e7 brd ff:ff:ff:ff:ff:ff protodown on <mlag,vrrp>
$ip link set dev vxlan0 protodown_reason mlag off
$ip link set dev vxlan0 protodown off protodown_reason vrrp off
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
We've added 5 non-merge commits during the last 21 day(s) which contain
a total of 5 files changed, 126 insertions(+), 18 deletions(-).
The main changes are:
1) Fix a map element leak in HASH_OF_MAPS map type, from Andrii Nakryiko.
2) Fix a NULL pointer dereference in __btf_resolve_helper_id() when no
btf_vmlinux is available, from Peilin Ye.
3) Init pos variable in __bpfilter_process_sockopt(), from Christoph Hellwig.
4) Fix a cgroup sockopt verifier test by specifying expected attach type,
from Jean-Philippe Brucker.
Note that when net gets merged into net-next later on, there is a small
merge conflict in kernel/bpf/btf.c between commit 42fd97e157b5 ("bpf: Fix
NULL pointer dereference in __btf_resolve_helper_id()") from the bpf tree
and commit 138b9a0511c7 ("bpf: Remove btf_id helpers resolving") from the
net-next tree.
Resolve as follows: remove the old hunk with the __btf_resolve_helper_id()
function. Change the btf_resolve_helper_id() so it actually tests for a
NULL btf_vmlinux and bails out:
int btf_resolve_helper_id(struct bpf_verifier_log *log,
const struct bpf_func_proto *fn, int arg)
{
int id;
if (fn->arg_type[arg] != ARG_PTR_TO_BTF_ID || !btf_vmlinux)
return -EINVAL;
id = fn->btf_id[arg];
if (!id || id > btf_vmlinux->nr_types)
return -EINVAL;
return id;
}
Let me know if you run into any others issues (CC'ing Jiri Olsa so he's in
the loop with regards to merge conflict resolution).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix policy matching with mark and mask on userspace interfaces.
From Xin Long.
2) Several fixes for the new ESP in TCP encapsulation.
From Sabrina Dubroca.
3) Fix crash when the hold queue is used. The assumption that
xdst->path and dst->child are not a NULL pointer only if dst->xfrm
is not a NULL pointer is true with the exception of using the
hold queue. Fix this by checking for hold queue usage before
dereferencing xdst->path or dst->child.
4) Validate pfkey_dump parameter before sending them.
From Mark Salyzyn.
5) Fix the location of the transport header with ESP in UDPv6
encapsulation. From Sabrina Dubroca.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: add earliest departure time to SCM_TIMESTAMPING_OPT_STATS
This change adds TCP_NLA_EDT to SCM_TIMESTAMPING_OPT_STATS that reports
the earliest departure time(EDT) of the timestamped skb. By tracking EDT
values of the skb from different timestamps, we can observe when and how
much the value changed. This allows to measure the precise delay
injected on the sender host e.g. by a bpf-base throttler.
Signed-off-by: Yousuk Seung <ysseung@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 Jul 2020 23:55:32 +0000 (16:55 -0700)]
Merge branch 'mptcp-syncookies'
Florian Westphal says:
====================
mptcp: add syncookie support
Changes in v2:
- first patch renames req->ts_cookie to req->syncookie instead of
removing ts_cookie member.
- patch to add 'want_cookie' arg to init_req() functions has been dropped.
All users of that arg were changed to check 'req->syncookie' instead.
v1 cover letter:
When syn-cookies are used the SYN?ACK never contains a MPTCP option,
because the code path that creates a request socket based on a valid
cookie ACK lacks the needed changes to construct MPTCP request sockets.
After this series, if SYN carries MP_CAPABLE option, the option is not
cleared anymore and request socket will be reconstructed using the
MP_CAPABLE option data that is re-sent with the ACK.
This means that no additional state gets encoded into the syn cookie or
the TCP timestamp.
There are two caveats for SYN-Cookies with MPTCP:
1. When syn-cookies are used, the server-generated key is not stored.
The drawback is that the next connection request that comes in before
the cookie-ACK has a small chance that it will generate the same local_key.
If this happens, the cookie ACK that comes in second will (re)compute the
token hash and then detects that this is already in use.
Unlike normal case, where the server will pick a new key value and then
re-tries, we can't do that because we already committed to the key value
(it was sent to peer already).
Im this case, MPTCP cannot be used and late TCP fallback happens.
2). SYN packets with a MP_JOIN requests cannot be handled without storing
state. This is because the SYN contains a nonce value that is needed to
verify the HMAC of the MP_JOIN ACK that completes the three-way
handshake. Also, a local nonce is generated and used in the cookie
SYN/ACK.
There are only 2 ways to solve this:
a) Do not support JOINs when cookies are in effect.
b) Store the nonces somewhere.
The approach chosen here is b).
Patch 8 adds a fixed-size (1024 entries) state table to store the
information required to validate the MP_JOIN ACK and re-build the
request socket.
State gets stored when syn-cookies are active and the token in the JOIN
request referred to an established MPTCP connection that can also accept
a new subflow.
State is restored if the ACK cookie is valid, an MP_JOIN option is present
and the state slot contains valid data from a previous SYN.
After the request socket has been re-build, normal HMAC check is done just
as without syn cookies.
Largely identical to last RFC, except patch #8 which follows Paolos
suggestion to use a private table storage area rather than keeping
request sockets around. This also means I dropped the patch to remove
const qualifier from sk_listener pointers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: mptcp: add test cases for mptcp join tests with syn cookies
Also add test cases with MP_JOIN when tcp_syncookies sysctl is 2 (i.e.,
syncookies are always-on).
While at it, also print the test number and add the test number
to the pcap files that can be generated optionally.
This makes it easier to match the pcap to the test case.
Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: mptcp: make 2nd net namespace use tcp syn cookies unconditionally
check we can establish connections also when syn cookies are in use.
Check that
MPTcpExtMPCapableSYNRX and MPTcpExtMPCapableACKRX increase for each
MPTCP test.
Check TcpExtSyncookiesSent and TcpExtSyncookiesRecv increase in netns2.
Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp: enable JOIN requests even if cookies are in use
JOIN requests do not work in syncookie mode -- for HMAC validation, the
peers nonce and the mptcp token (to obtain the desired connection socket
the join is for) are required, but this information is only present in the
initial syn.
So either we need to drop all JOIN requests once a listening socket enters
syncookie mode, or we need to store enough state to reconstruct the request
socket later.
This adds a state table (1024 entries) to store the data present in the
MP_JOIN syn request and the random nonce used for the cookie syn/ack.
When a MP_JOIN ACK passed cookie validation, the table is consulted
to rebuild the request socket from it.
An alternate approach would be to "cancel" syn-cookie mode and force
MP_JOIN to always use a syn queue entry.
However, doing so brings the backlog over the configured queue limit.
v2: use req->syncookie, not (removed) want_cookie arg
Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: syncookies: create mptcp request socket for ACK cookies with MPTCP option
If SYN packet contains MP_CAPABLE option, keep it enabled.
Syncokie validation and cookie-based socket creation is changed to
instantiate an mptcp request sockets if the ACK contains an MPTCP
connection request.
Rather than extend both cookie_v4/6_check, add a common helper to create
the (mp)tcp request socket.
Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used to initialize the mptcp request socket when a MP_CAPABLE
request was handled in syncookie mode, i.e. when a TCP ACK containing a
MP_CAPABLE option is a valid syncookie value.
Normally (non-cookie case), MPTCP will generate a unique 32 bit connection
ID and stores it in the MPTCP token storage to be able to retrieve the
mptcp socket for subflow joining.
In syncookie case, we do not want to store any state, so just generate the
unique ID and use it in the reply.
This means there is a small window where another connection could generate
the same token.
When Cookie ACK comes back, we check that the token has not been registered
in the mean time. If it was, the connection needs to fall back to TCP.
Changes in v2:
- use req->syncookie instead of passing 'want_cookie' arg to ->init_req()
(Eric Dumazet)
Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mptcp: rename and export mptcp_subflow_request_sock_ops
syncookie code path needs to create an mptcp request sock.
Prepare for this and add mptcp prefix plus needed export of ops struct.
Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When syncookie support is added, we will need to add a variant of
subflow_init_req() helper. It will do almost same thing except
that it will not compute/add a token to the mptcp token tree.
To avoid excess copy&paste, this commit splits away part of the
code into a new helper, __subflow_init_req, that can then be re-used
from the 'no insert' function added in a followup change.
Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Once syncookie support is added, no state will be stored anymore when the
syn/ack is generated in syncookie mode.
When the ACK comes back, the generated key will be taken from the TCP ACK,
the token is re-generated and inserted into the token tree.
This means we can't retry with a new key when the token is already taken
in the syncookie case.
Therefore, move the retry logic to the caller to prepare for syncookie
support in mptcp.
Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peilin Ye [Thu, 30 Jul 2020 19:20:26 +0000 (15:20 -0400)]
rds: Prevent kernel-infoleak in rds_notify_queue_get()
rds_notify_queue_get() is potentially copying uninitialized kernel stack
memory to userspace since the compiler may leave a 4-byte hole at the end
of `cmsg`.
In 2016 we tried to fix this issue by doing `= { 0 };` on `cmsg`, which
unfortunately does not always initialize that 4-byte hole. Fix it by using
memset() instead.
Cc: stable@vger.kernel.org Fixes: e424af85ffaa ("rds: fix a leak of kernel memory") Fixes: 6a8e52eba9d0 ("RDS: recv.c") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper, in multiple places, instead
of an open-coded version in order to avoid any potential type
mistakes and protect against potential integer overflows.
Also, remove unnecessary object identifier size.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
please apply the following patch series for qeth to netdev's net-next tree.
This primarily brings some modernization to the RX path, laying the
groundwork for smarter RX refill policies.
Some of the patches are tagged as fixes, but really target only rare /
theoretical issues. So given where we are in the release cycle and that we
touch the main RX path, taking them through net-next seems more appropriate.
====================
Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Discard events that don't contain any entries. This shouldn't happen,
but subsequent code relies on being able to use entry 0. So better
be safe than accessing garbage.
Fixes: 415d00be3e08 ("qeth: bridgeport support - basic control") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Running a RX refill outside of NAPI context is inherently racy, even
though the worker is only started for an entirely idle RX ring.
>From the moment that the worker has replenished parts of the RX ring,
the HW can use those RX buffers, raise an IRQ and cause our NAPI code to
run concurrently to the RX refill worker.
Instead let the worker schedule our NAPI instance, and refill the RX
ring from there. Keeping accurate count of how many buffers still need
to be refilled also removes some quirky arithmetic from the low-level
code.
Fixes: 68abee9432ec ("qeth: add support for af_iucv HiperSockets transport") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When preparing a buffer for RX refill, tolerate that it already has a
pool_entry attached. Otherwise we could easily leak such a pool_entry
when re-driving the RX refill after an error (from eg. do_qdio()).
This needs some minor adjustment in the code that drains RX buffer(s)
prior to RX refill and during teardown, so that ->pool_entry is NULLed
accordingly.
Fixes: a5a090d6ef88 ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/sched: The error lable position is corrected in ct_init_module
Exchange the positions of the err_tbl_init and err_register labels in
ct_init_module function.
Fixes: d042927a6c1a ("net/sched: act_ct: Create nf flow table per zone") Signed-off-by: liujian <liujian56@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 Jul 2020 23:15:03 +0000 (16:15 -0700)]
bluetooth: sco: Fix sockptr reference.
net/bluetooth/sco.c: In function ‘sco_sock_setsockopt’:
net/bluetooth/sco.c:862:3: error: cannot convert to a pointer type
862 | if (get_user(opt, (u32 __user *)optval)) {
| ^~
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the main bluetooth-next pull request for 5.9:
- Fix firmware filenames for Marvell chipsets
- Several suspend-related fixes
- Addedd mgmt commands for runtime configuration
- Multiple fixes for Qualcomm-based controllers
- Add new monitoring feature for mgmt
- Fix handling of legacy cipher (E4) together with security level 4
- Add support for Realtek 8822CE controller
- Fix issues with Chinese controllers using fake VID/PID values
- Multiple other smaller fixes & improvements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some I2C core improvements to prevent NULL pointer usage and a
MAINTAINERS update"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: slave: add sanity check when unregistering
i2c: slave: improve sanity check when registering
MAINTAINERS: Update GENI I2C maintainers list
i2c: also convert placeholder function to return errno
Merge tag 'powerpc-5.8-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
"Fix a bug introduced by the changes we made to lockless page table
walking this cycle.
When using the hash MMU, and perf with callchain recording, we can
deadlock if the PMI interrupts a hash fault, and the callchain
recording then takes a hash fault on the same page.
Thanks to Nicholas Piggin, Aneesh Kumar K.V, Anton Blanchard, and
Athira Rajeev"
* tag 'powerpc-5.8-8' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s/hash: Fix hash_preload running with interrupts enabled
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main one is to fix the build after Willy's per-cpu entropy changes
this week. Although that was already resolved elsewhere, the arm64 fix
here is useful cleanup anyway.
Other than that, we've got a fix for building with Clang's integrated
assembler and a fix to make our IPv4 checksumming robust against
invalid header lengths (this only seems to be triggerable by injected
errors).
- Fix build breakage due to circular headers
- Fix build regression when using Clang's integrated assembler
- Fix IPv4 header checksum code to deal with invalid length field
- Fix broken path for Arm PMU entry in MAINTAINERS"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
MAINTAINERS: Include drivers subdirs for ARM PMU PROFILING AND DEBUGGING entry
arm64: csum: Fix handling of bad packets
arm64: Drop unnecessary include from asm/smp.h
arm64/alternatives: move length validation inside the subsection
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- avoid invoking overflow handler for uaccess watchpoints
- fix incorrect clock_gettime64 availability
- fix EFI crash in create_mapping_late()
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8988/1: mmu: fix crash in EFI calls due to p4d typo in create_mapping_late()
ARM: 8987/1: VDSO: Fix incorrect clock_gettime64
ARM: 8986/1: hw_breakpoint: Don't invoke overflow handler on uaccess watchpoints
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Two more merge window regressions, a corruption bug in hfi1 and a few
other small fixes.
- Missing user input validation regression in ucma
- Disallowing a previously allowed user combination regression in
mlx5
- ODP prefetch memory leaking triggerable by userspace
- Memory corruption in hf1 due to faulty ring buffer logic
- Missed mutex initialization crash in mlx5
- Two small defects with RDMA DIM"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/core: Free DIM memory in error unwind
RDMA/core: Stop DIM before destroying CQ
RDMA/mlx5: Initialize QP mutex for the debug kernels
IB/rdmavt: Fix RQ counting issues causing use of an invalid RWQE
RDMA/mlx5: Allow providing extra scatter CQE QP flag
RDMA/mlx5: Fix prefetch memory leak if get_prefetchable_mr fails
RDMA/cm: Add min length checks to user structure copies
Merge tag 'sound-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few wrap-up small fixes for the usual HD-audio and USB-audio stuff:
- A regression fix for S3 suspend on old Intel platforms
- A fix for possible Oops in ASoC HD-audio binding
- Trivial quirks for various devices"
* tag 'sound-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fixed HP right speaker no sound
ALSA: hda: fix NULL pointer dereference during suspend
ALSA: hda/hdmi: Fix keep_power assignment for non-component devices
ALSA: hda: Workaround for spurious wakeups on some Intel platforms
ALSA: hda/realtek: Fix add a "ultra_low_power" function for intel reference board (alc256)
ALSA: hda/realtek: typo_fix: enable headset mic of ASUS ROG Zephyrus G14(GA401) series with ALC289
ALSA: hda/realtek: enable headset mic of ASUS ROG Zephyrus G15(GA502) series with ALC289
ALSA: usb-audio: Add implicit feedback quirk for SSL2
Ben Hutchings [Sat, 25 Jul 2020 01:06:23 +0000 (02:06 +0100)]
libtraceevent: Fix build with binutils 2.35
In binutils 2.35, 'nm -D' changed to show symbol versions along with
symbol names, with the usual @@ separator. When generating
libtraceevent-dynamic-list we need just the names, so strip off the
version suffix if present.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Reviewed-by: Steven Rostedt <rostedt@goodmis.org> Cc: linux-trace-devel@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Wei Li [Fri, 24 Jul 2020 07:11:10 +0000 (15:11 +0800)]
perf tools: Fix record failure when mixed with ARM SPE event
When recording with cache-misses and arm_spe_x event, I found that it
will just fail without showing any error info if i put cache-misses
after 'arm_spe_x' event.
[root@localhost 0620]# perf record -e cache-misses \
-e arm_spe_0/ts_enable=1,pct_enable=1,pa_enable=1,load_filter=1,jitter=1,store_filter=1,min_latency=0/ sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.067 MB perf.data ]
[root@localhost 0620]#
[root@localhost 0620]# perf record -e arm_spe_0/ts_enable=1,pct_enable=1,pa_enable=1,load_filter=1,jitter=1,store_filter=1,min_latency=0/ \
-e cache-misses sleep 1
[root@localhost 0620]#
The current code can only work if the only event to be traced is an
'arm_spe_x', or if it is the last event to be specified. Otherwise the
last event type will be checked against all the arm_spe_pmus[i]->types,
none will match and an out of bound 'i' index will be used in
arm_spe_recording_init().
We don't support concurrent multiple arm_spe_x events currently, that
is checked in arm_spe_recording_options(), and it will show the relevant
info. So add the check and record of the first found 'arm_spe_pmu' to
fix this issue here.
Fixes: 8990eef61845 ("perf tools: Add ARM Statistical Profiling Extensions (SPE) support") Signed-off-by: Wei Li <liwei391@huawei.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Tested-by-by: Leo Yan <leo.yan@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kim Phillips <kim.phillips@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lore.kernel.org/lkml/20200724071111.35593-2-liwei391@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Thomas Richter [Wed, 29 Jul 2020 13:53:14 +0000 (15:53 +0200)]
perf tests: Fix test 68 zstd compression for s390
Commit bd99740ff4bc ("s390/cpum_sf: prohibit callchain data collection")
prohibits call graph sampling for hardware events on s390. The
information recorded is out of context and does not match.
On s390 this commit now breaks test case 68 Zstd perf.data
compression/decompression.
Therefore omit call graph sampling on s390 in this test.
Output before:
[root@t35lp46 perf]# ./perf test -Fv 68
68: Zstd perf.data compression/decompression :
--- start ---
Collecting compressed record file:
Error:
cycles: PMU Hardware doesn't support sampling/overflow-interrupts.
Try 'perf stat'
---- end ----
Zstd perf.data compression/decompression: FAILED!
[root@t35lp46 perf]#
Output after:
[root@t35lp46 perf]# ./perf test -Fv 68
68: Zstd perf.data compression/decompression :
--- start ---
Collecting compressed record file:
500+0 records in
500+0 records out
256000 bytes (256 kB, 250 KiB) copied, 0.00615638 s, 41.6 MB/s
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.004 MB /tmp/perf.data.X3M,
compressed (original 0.002 MB, ratio is 3.609) ]
Checking compressed events stats:
# compressed : Zstd, level = 1, ratio = 4
COMPRESSED events: 1
2ELIFREPh---- end ----
Zstd perf.data compression/decompression: Ok
[root@t35lp46 perf]#
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Reviewed-by: Sumanth Korikkar <sumanthk@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Link: http://lore.kernel.org/lkml/20200729135314.91281-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
tools lib traceevent: Fix memory leak in process_dynamic_array_len
I compiled with AddressSanitizer and I had these memory leaks while I
was using the tep_parse_format function:
Direct leak of 28 byte(s) in 4 object(s) allocated from:
#0 0x7fb07db49ffe in __interceptor_realloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10dffe)
#1 0x7fb07a724228 in extend_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:985
#2 0x7fb07a724c21 in __read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1140
#3 0x7fb07a724f78 in read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1206
#4 0x7fb07a725191 in __read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1291
#5 0x7fb07a7251df in read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1299
#6 0x7fb07a72e6c8 in process_dynamic_array_len /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:2849
#7 0x7fb07a7304b8 in process_function /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3161
#8 0x7fb07a730900 in process_arg_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3207
#9 0x7fb07a727c0b in process_arg /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1786
#10 0x7fb07a731080 in event_read_print_args /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3285
#11 0x7fb07a731722 in event_read_print /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3369
#12 0x7fb07a740054 in __tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6335
#13 0x7fb07a74047a in __parse_event /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6389
#14 0x7fb07a740536 in tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6431
#15 0x7fb07a785acf in parse_event ../../../src/fs-src/fs.c:251
#16 0x7fb07a785ccd in parse_systems ../../../src/fs-src/fs.c:284
#17 0x7fb07a786fb3 in read_metadata ../../../src/fs-src/fs.c:593
#18 0x7fb07a78760e in ftrace_fs_source_init ../../../src/fs-src/fs.c:727
#19 0x7fb07d90c19c in add_component_with_init_method_data ../../../../src/lib/graph/graph.c:1048
#20 0x7fb07d90c87b in add_source_component_with_initialize_method_data ../../../../src/lib/graph/graph.c:1127
#21 0x7fb07d90c92a in bt_graph_add_source_component ../../../../src/lib/graph/graph.c:1152
#22 0x55db11aa632e in cmd_run_ctx_create_components_from_config_components ../../../src/cli/babeltrace2.c:2252
#23 0x55db11aa6fda in cmd_run_ctx_create_components ../../../src/cli/babeltrace2.c:2347
#24 0x55db11aa780c in cmd_run ../../../src/cli/babeltrace2.c:2461
#25 0x55db11aa8a7d in main ../../../src/cli/babeltrace2.c:2673
#26 0x7fb07d5460b2 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x270b2)
The token variable in the process_dynamic_array_len function is
allocated in the read_expect_type function, but is not freed before
calling the read_token function.
Free the token variable before calling read_token in order to plug the
leak.
Johannes Berg [Thu, 30 Jul 2020 13:52:13 +0000 (15:52 +0200)]
mac80211: warn only once in check_sdata_in_driver() at each caller
Ben Greear has repeatedly reported in the past (for a few years
probably) that this triggers repeatedly in certain scenarios.
Make this a macro so that each callsite can trigger the warning
only once - that will still give us an idea of what's going on
and what paths can reach it, but avoids being too noisy.
Chung-Hsien Hsu [Tue, 23 Jun 2020 13:49:35 +0000 (08:49 -0500)]
nl80211: support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
Let drivers advertise support for AP-mode WPA/WPA2-PSK 4-way handshake
offloading with a new NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK flag.
Extend use of NL80211_ATTR_PMK attribute indicating it might be passed
as part of NL80211_CMD_START_AP command, and contain the PSK (which is
the PMK, hence the name).
The driver is assumed to handle the 4-way handshake by itself in this
case, instead of relying on userspace.
Johannes Berg [Thu, 30 Jul 2020 11:00:52 +0000 (13:00 +0200)]
cfg80211: invert HE BSS color 'disabled' to 'enabled'
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Felix Fietkau [Sun, 26 Jul 2020 11:06:11 +0000 (13:06 +0200)]
mac80211: add a function for running rx without passing skbs to the stack
This can be used to run mac80211 rx processing on a batch of frames in NAPI
poll before passing them to the network stack in a large batch.
This can improve icache footprint, or it can be used to pass frames via
netif_receive_skb_list.
mac80211: parse radiotap header when selecting Tx queue
Already parse the radiotap header in ieee80211_monitor_select_queue.
In a subsequent commit this will allow us to add a radiotap flag that
influences the queue on which injected packets will be sent.
This also fixes the incomplete validation of the injected frame in
ieee80211_monitor_select_queue: currently an out of bounds memory
access may occur in in the called function ieee80211_select_queue_80211
if the 802.11 header is too small.
Note that in ieee80211_monitor_start_xmit the radiotap header is parsed
again, which is necessairy because ieee80211_monitor_select_queue is not
always called beforehand.
mac80211: use same flag everywhere to avoid sequence number overwrite
Use the IEEE80211_TX_CTRL_NO_SEQNO flag in ieee80211_tx_info to mark
probe requests whose sequence number must not be overwritten. This
provides consistency with the radiotap flag that can be set to indicate
that the sequence number of an injected frame should not be overwritten.
mac80211: add radiotap flag to prevent sequence number overwrite
The radiotap specification contains a flag to indicate that the sequence
number of an injected frame should not be overwritten. Parse this flag
and define and set a corresponding Tx control flag.
mac80211: never drop injected frames even if normally not allowed
In ieee80211_tx_dequeue there is a check to see if the dequeued frame
is allowed in the current state. Injected frames that are normally
not allowed are being be dropped here. Fix this by checking if a
frame was injected and if so always allowing it.
Felix Fietkau [Fri, 24 Jul 2020 18:28:16 +0000 (20:28 +0200)]
mac80211: improve AQL tx airtime estimation
AQL does not take into account that most HT/VHT/HE traffic is A-MPDU aggregated.
Because of that, the per-packet airtime overhead is vastly overestimated.
Improve it by assuming an average aggregation length of 16 for non-legacy
traffic if not using the VO AC queue.
This should improve performance with high data rates, especially with multiple
stations
Markus Theil [Thu, 11 Jun 2020 14:02:37 +0000 (16:02 +0200)]
cfg80211/mac80211: add connected to auth server to meshconf
Besides information about num of peerings and gate connectivity,
the mesh formation byte also contains a flag for authentication
server connectivity, that currently cannot be set in the mesh conf.
This patch adds this capability, which is necessary to implement
802.1X authentication in mesh mode.
Linus Lüssing [Wed, 17 Jun 2020 07:30:33 +0000 (09:30 +0200)]
cfg80211/mac80211: add mesh_param "mesh_nolearn" to skip path discovery
Currently, before being able to forward a packet between two 802.11s
nodes, both a PLINK handshake is performed upon receiving a beacon and
then later a PREQ/PREP exchange for path discovery is performed on
demand upon receiving a data frame to forward.
When running a mesh protocol on top of an 802.11s interface, like
batman-adv, we do not need the multi-hop mesh routing capabilities of
802.11s and usually set mesh_fwding=0. However, even with mesh_fwding=0
the PREQ/PREP path discovery is still performed on demand. Even though
in this scenario the next hop PREQ/PREP will determine is always the
direct 11s neighbor node.
The new mesh_nolearn parameter allows to skip the PREQ/PREP exchange in
this scenario, leading to a reduced delay, reduced packet buffering and
simplifies HWMP in general.
mesh_nolearn is still rather conservative in that if the packet destination
is not a direct 11s neighbor, it will fall back to PREQ/PREP path
discovery.
For normal, multi-hop 802.11s mesh routing it is usually not advisable
to enable mesh_nolearn as a transmission to a direct but distant neighbor
might be worse than reaching that same node via a more robust /
higher throughput etc. multi-hop path.
Cc: Sven Eckelmann <sven@narfation.org> Cc: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Link: https://lore.kernel.org/r/20200617073034.26149-1-linus.luessing@c0d3.blue
[fix nl80211 policy to range 0/1 only] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: allow the low level driver to flush the BSS table
The low level driver adds its own opaque information
in the BSS table in the cfg80211_bss structure.
The low level driver may need to signal that this information
is no longer relevant and needs to be recreated.
Add an API to allow the low level driver to do that.
iwlwifi needs this because it keeps there an information about
the firmware's internal clock. This is kept in mac80211's
struct ieee80211_bss::sync_device_ts.
This information is populated while we scan, we add the
internal firmware's clock to each beacon which allows us to
program the firmware correctly after association so that
it'll know when (in terms of its internal clock) the DTIM
and TBTT will happen.
When the firmware is reset this internal clock is reset as
well and ieee80211_bss::sync_device_ts is no longer accurate.
iwlwifi will call this new API any time the firmware is started.
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
nl80211: Remove a misleading label in 'nl80211_trigger_scan()'
Since commit 0403a5ec2fc0 ("cfg80211: vastly simplify locking"), the
'unlock' label at the end of 'nl80211_trigger_scan()' is useless and
misleading, because nothing is unlocked there.
Direct return can be used instead of 'err = -<error code>; goto unlock;'
construction.
Randy Dunlap [Wed, 15 Jul 2020 16:43:25 +0000 (09:43 -0700)]
net/wireless: regulatory.h: drop duplicate word in comment
Drop doubled word "of" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: netdev@vger.kernel.org Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Cc: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20200715164325.9109-5-rdunlap@infradead.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Randy Dunlap [Wed, 15 Jul 2020 16:43:24 +0000 (09:43 -0700)]
net/wireless: mac80211.h: drop duplicate words in comments
Drop doubled words "are" and "by" in comments.
Change doubled "to to" to "to the".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: netdev@vger.kernel.org Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Cc: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20200715164325.9109-4-rdunlap@infradead.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Randy Dunlap [Wed, 15 Jul 2020 16:43:23 +0000 (09:43 -0700)]
net/wireless: cfg80211.h: drop duplicate words in comments
Drop doubled word "by" in a comment.
Change "operate in in" to "operate with in" as is used below.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: netdev@vger.kernel.org Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Cc: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20200715164325.9109-3-rdunlap@infradead.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Randy Dunlap [Wed, 15 Jul 2020 16:43:22 +0000 (09:43 -0700)]
net/wireless: wireless.h: drop duplicate word in comments
Drop doubled word "threshold" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: netdev@vger.kernel.org Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Cc: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20200715164325.9109-2-rdunlap@infradead.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Randy Dunlap [Wed, 15 Jul 2020 16:43:21 +0000 (09:43 -0700)]
net/wireless: nl80211.h: drop duplicate words in comments
Drop doubled words in several comments.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: netdev@vger.kernel.org Cc: Kalle Valo <kvalo@codeaurora.org> Cc: linux-wireless@vger.kernel.org Cc: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20200715164325.9109-1-rdunlap@infradead.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: allow vendor dumpit to terminate by returning 0
nl80211 vendor netlink dumpit, like netlink_callback->dump, should
signal successful completion by returning 0.
Currently, that will just cause dumpit to be called again, possibly
many times until an error occurs. Since skb->len is never going to be
0 by the time dumpit is called, the only way for dumpit to signal
completion is by returning an error. If it returns a positive value,
the current message is cancelled, but that positive value is returned
and nl80211_vendor_cmd_dump gets called again.
Colin Ian King [Wed, 22 Jul 2020 15:38:30 +0000 (16:38 +0100)]
mac80211: remove the need for variable rates_idx
Currently rates_idx is being initialized with the value -1 and this
value is never read so the initialization is redundant and can be
removed. The next time the variable is used it is assigned a value
that is returned a few statements later. Just return i - 1 and
remove the need for rates_idx.
Bluetooth: use the proper scan params when conn is pending
When an LE connection is requested and an RPA update is needed via
hci_connect_le_scan, the default scanning parameters are used rather
than the connect parameters. This leads to significant delays in the
connection establishment process when using lower duty cycle scanning
parameters.
The patch simply looks at the pended connection list when trying to
determine which scanning parameters should be used.
Before:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#378 [hci0] 1659.247156
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 367.500 msec (0x024c)
Window: 37.500 msec (0x003c)
After:
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
#39 [hci0] 7.422109
Own address type: Public (0x00)
Filter policy: Ignore not in white list (0x01)
PHYs: 0x01
Entry 0: LE 1M
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 60.000 msec (0x0060)
Merge tag 'drm-fixes-2020-07-31' of git://anongit.freedesktop.org/drm/drm
Pull more drm fixes from Dave Airlie:
"As mentioned previously this contains the nouveau regression fix.
amdgpu had three fixes outstanding as well, one revert, an info leak
and use after free. The use after free is a bit trickier than I'd
like, and I've personally gone over it to confirm I'm happy that it is
doing what it says.
nouveau:
- final modifiers regression fix
amdgpu:
- Revert a fix which caused other regressions
- Fix potential kernel info leak
- Fix a use-after-free bug that was uncovered by another change in 5.7"
* tag 'drm-fixes-2020-07-31' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau: Accept 'legacy' format modifiers
Revert "drm/amdgpu: Fix NULL dereference in dpm sysfs handlers"
drm/amd/display: Clear dm_state for fast updates
drm/amdgpu: Prevent kernel-infoleak in amdgpu_info_ioctl()
Dave Airlie [Fri, 31 Jul 2020 03:04:00 +0000 (13:04 +1000)]
Merge tag 'amd-drm-fixes-5.8-2020-07-30' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.8-2020-07-30:
amdgpu:
- Revert a fix which caused other regressions
- Fix potential kernel info leak
- Fix a use-after-free bug that was uncovered by another change in 5.7
James Jones [Thu, 30 Jul 2020 23:58:23 +0000 (16:58 -0700)]
drm/nouveau: Accept 'legacy' format modifiers
Accept the DRM_FORMAT_MOD_NVIDIA_16BX2_BLOCK()
family of modifiers to handle broken userspace
Xorg modesetting and Mesa drivers. Existing Mesa
drivers are still aware of only these older
format modifiers which do not differentiate
between different variations of the block linear
layout. When the format modifier support flag was
flipped in the nouveau kernel driver, the X.org
modesetting driver began attempting to use its
format modifier-enabled framebuffer path. Because
the set of format modifiers advertised by the
kernel prior to this change do not intersect with
the set of format modifiers advertised by Mesa,
allocating GBM buffers using format modifiers
fails and the modesetting driver falls back to
non-modifier allocation. However, it still later
queries the modifier of the GBM buffer when
creating its DRM-KMS framebuffer object, receives
the old-format modifier from Mesa, and attempts
to create a framebuffer with it. Since the kernel
is still not aware of these formats, this fails.
Userspace should not be attempting to query format
modifiers of GBM buffers allocated with a non-
format-modifier-aware allocation path, but to
avoid breaking existing userspace behavior, this
change accepts the old-style format modifiers when
creating framebuffers and applying them to planes
by translating them to the equivalent new-style
modifier. To accomplish this, some layout
parameters must be assumed to match properties of
the device targeted by the relevant ioctls. To
avoid perpetuating misuse of the old-style
modifiers, this change does not advertise support
for them. Doing so would imply compatibility
between devices with incompatible memory layouts.
Reported-by: Kirill A. Shutemov <kirill@shutemov.name> Fixes: f8eeaaa1cbec ("drm/nouveau/kms: Support NVIDIA format modifiers") Link: https://lkml.org/lkml/2020/6/30/1251 Signed-off-by: James Jones <jajones@nvidia.com> Acked-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
net/mlx5e: fix bpf_prog reference count leaks in mlx5e_alloc_rq
The function invokes bpf_prog_inc(), which increases the reference
count of a bpf_prog object "rq->xdp_prog" if the object isn't NULL.
The refcount leak issues take place in two error handling paths. When
either mlx5_wq_ll_create() or mlx5_wq_cyc_create() fails, the function
simply returns the error code and forgets to drop the reference count
increased earlier, causing a reference count leak of "rq->xdp_prog".
Fix this issue by jumping to the error handling path err_rq_wq_destroy
while either function fails.
Fixes: 91042d25c3f5 ("net/mlx5e: RX, Split WQ objects for different RQ types") Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Jianbo Liu [Fri, 3 Jul 2020 02:34:23 +0000 (02:34 +0000)]
net/mlx5e: E-Switch, Specify flow_source for rule with no in_port
The flow_source must be specified, even for rule without matching
source vport, because some actions are only allowed in uplink.
Otherwise, rule can't be offloaded and firmware syndrome happens.
Fixes: c41ef6f5d9a3 ("net/mlx5: E-Switch, Add support for offloading rules with no in_port") Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Chris Mi <chrism@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Jianbo Liu [Thu, 2 Jul 2020 01:06:37 +0000 (01:06 +0000)]
net/mlx5e: E-Switch, Add misc bit when misc fields changed for mirroring
The modified flow_context fields in FTE must be indicated in
modify_enable bitmask. Previously, the misc bit in modify_enable is
always set as source vport must be set for each rule. So, when parsing
vxlan/gre/geneve/qinq rules, this bit is not set because those are all
from the same misc fileds that source vport fields are located at, and
we don't need to set the indicator twice.
After adding per vport tables for mirroring, misc bit is not set, then
firmware syndrome happens. To fix it, set the bit wherever misc fileds
are changed. This also makes it unnecessary to check misc fields and set
the misc bit accordingly in metadata matching, so here remove it.
Besides, flow_source must be specified for uplink because firmware
will check it and some actions are only allowed for packets received
from uplink.
Fixes: 9dcde02e5029 ("net/mlx5e: Eswitch, Use per vport tables for mirroring") Signed-off-by: Jianbo Liu <jianbol@mellanox.com> Reviewed-by: Chris Mi <chrism@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
David S. Miller [Fri, 31 Jul 2020 00:47:34 +0000 (17:47 -0700)]
Merge tag 'mac80211-for-davem-2020-07-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of more changes:
* remove a warning that can trigger in certain races
* check a function pointer before using it
* check before adding 6 GHz to avoid a warning in mesh
* fix two memory leaks in mesh
* fix a TX status bug leading to a memory leak
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Hai [Thu, 30 Jul 2020 07:30:00 +0000 (15:30 +0800)]
net: gemini: Fix missing clk_disable_unprepare() in error path of gemini_ethernet_port_probe()
Fix the missing clk_disable_unprepare() before return
from gemini_ethernet_port_probe() in the error handling case.
Fixes: a8b83602f149 ("net: ethernet: Add a driver for Gemini gigabit ethernet") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log