Marc Zyngier [Sun, 27 May 2018 15:14:15 +0000 (16:14 +0100)]
irqchip/gic-v3-its: Refactor LPI allocator
Our current LPI allocator relies on a bitmap, each bit representing
a chunk of 32 LPIs, meaning that each device gets allocated LPIs
in multiple of 32. It served us well so far, but new use cases now
require much more finer grain allocations, down the the individual
LPI.
Given the size of the IntID space (up to 32bit), it isn't practical
to continue using a bitmap, so let's use a different data structure
altogether.
We switch to a list, where each element represent a contiguous range
of LPIs. On allocation, we simply grab the first group big enough to
satisfy the allocation, and substract what we need from it. If the
group becomes empty, we just remove it. On freeing interrupts, we
insert a new group of interrupt in the list, sort it and fuse the
adjacent groups.
This makes freeing interrupt much more expensive than allocating
them (an unusual behaviour), but that's fine as long as we consider
that freeing interrupts is an extremely rare event.
We still allocate interrupts in blocks of 32 for the time being,
but subsequent patches will relax this.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
- A fix for OMAP5 and DRA7 to make the branch predictor hardening
settings take proper effect on secondary cores
- Disable USB OTG on am3517 since current driver isn't working
- Fix thermal sensor register settings on Armada 38x
- Fix suspend/resume IRQs on pxa3xx
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
ARM: pxa: irq: fix handling of ICMR registers in suspend/resume
ARM: dts: armada-38x: use the new thermal binding
Merge tag 'rtc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for 4.18:
- an important core fix for RTCs using the core offsetting only one
driver is affected
- a fix for the error path of mrst"
* tag 'rtc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: fix alarm read and set offset
rtc: mrst: fix error code in probe()
Olof Johansson [Sat, 14 Jul 2018 22:14:02 +0000 (15:14 -0700)]
Merge tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two omap fixes for v4.18-rc cycle
Turns out the recent patches for ARM branch predictor hardening are
not working on omap5 and dra7 as planned because the secondary CPU
is parked to the bootrom code. We can't configure it in the bootloader.
So we must enable invalidates of BTB for omap5 and dra7 secondary
core in the kernel.
And there's a fix for reserved register access for am3517. The
usb otg module on am3517 is not the same as for other omap3.
* tag 'omap-for-v4.18/fixes-rc4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
Merge tag 'for-linus-4.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two related fixes for a boot failure of Xen PV guests"
* tag 'for-linus-4.18-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: setup pv irq ops vector earlier
xen: remove global bit from __default_kernel_pte_mask for pv guests
* emailed patches form Andrew Morton <akpm@linux-foundation.org>:
reiserfs: fix buffer overflow with long warning messages
checkpatch: fix duplicate invalid vsprintf pointer extension '%p<foo>' messages
mm: do not bug_on on incorrect length in __mm_populate()
mm/memblock.c: do not complain about top-down allocations for !MEMORY_HOTREMOVE
fs, elf: make sure to page align bss in load_elf_library
x86/purgatory: add missing FORCE to Makefile target
net/9p/client.c: put refcount of trans_mod in error case in parse_opts()
mm: allow arch to supply p??_free_tlb functions
autofs: fix slab out of bounds read in getname_kernel()
fs/proc/task_mmu.c: fix Locked field in /proc/pid/smaps*
mm: do not drop unused pages when userfaultd is running
Eric Biggers [Fri, 13 Jul 2018 23:59:27 +0000 (16:59 -0700)]
reiserfs: fix buffer overflow with long warning messages
ReiserFS prepares log messages into a 1024-byte buffer with no bounds
checks. Long messages, such as the "unknown mount option" warning when
userspace passes a crafted mount options string, overflow this buffer.
This causes KASAN to report a global-out-of-bounds write.
Fix it by truncating messages to the buffer size.
Link: http://lkml.kernel.org/r/20180707203621.30922-1-ebiggers3@gmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+b890b3335a4d8c608963@syzkaller.appspotmail.com Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reason is that the length of the new brk is not page aligned when we
try to populate the it. There is no reason to bug on that though.
do_brk_flags already aligns the length properly so the mapping is
expanded as it should. All we need is to tell mm_populate about it.
Besides that there is absolutely no reason to to bug_on in the first
place. The worst thing that could happen is that the last page wouldn't
get populated and that is far from putting system into an inconsistent
state.
Fix the issue by moving the length sanitization code from do_brk_flags
up to vm_brk_flags. The only other caller of do_brk_flags is brk
syscall entry and it makes sure to provide the proper length so t here
is no need for sanitation and so we can use do_brk_flags without it.
Also remove the bogus BUG_ONs.
[osalvador@techadventures.net: fix up vm_brk_flags s@request@len@] Link: http://lkml.kernel.org/r/20180706090217.GI32658@dhcp22.suse.cz Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: syzbot <syzbot+5dcb560fe12aa5091c06@syzkaller.appspotmail.com> Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: "Huang, Ying" <ying.huang@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Fri, 13 Jul 2018 23:59:16 +0000 (16:59 -0700)]
mm/memblock.c: do not complain about top-down allocations for !MEMORY_HOTREMOVE
Mike Rapoport is converting architectures from bootmem to nobootmem
allocator. While doing so for m68k Geert has noticed that he gets a
scary looking warning:
The warning is basically saying that a top-down allocation can break
memory hotremove because memblock allocation is not movable. But m68k
doesn't even support MEMORY_HOTREMOVE so there is no point to warn about
it.
Make the warning conditional only to configurations that care.
Link: http://lkml.kernel.org/r/20180706061750.GH32658@dhcp22.suse.cz Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Tested-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Greg Ungerer <gerg@linux-m68k.org> Cc: Sam Creasey <sammy@sammy.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oscar Salvador [Fri, 13 Jul 2018 23:59:13 +0000 (16:59 -0700)]
fs, elf: make sure to page align bss in load_elf_library
The current code does not make sure to page align bss before calling
vm_brk(), and this can lead to a VM_BUG_ON() in __mm_populate() due to
the requested lenght not being correctly aligned.
Let us make sure to align it properly.
Kees: only applicable to CONFIG_USELIB kernels: 32-bit and configured
for libc5.
Link: http://lkml.kernel.org/r/20180705145539.9627-1-osalvador@techadventures.net Signed-off-by: Oscar Salvador <osalvador@suse.de> Reported-by: syzbot+5dcb560fe12aa5091c06@syzkaller.appspotmail.com Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Acked-by: Kees Cook <keescook@chromium.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Philipp Rudo [Fri, 13 Jul 2018 23:59:09 +0000 (16:59 -0700)]
x86/purgatory: add missing FORCE to Makefile target
- Build the kernel without the fix
- Add some flag to the purgatories KBUILD_CFLAGS,I used
-fno-asynchronous-unwind-tables
- Re-build the kernel
When you look at makes output you see that sha256.o is not re-build in the
last step. Also readelf -S still shows the .eh_frame section for
sha256.o.
With the fix sha256.o is rebuilt in the last step.
Without FORCE make does not detect changes only made to the command line
options. So object files might not be re-built even when they should be.
Fix this by adding FORCE where it is missing.
Link: http://lkml.kernel.org/r/20180704110044.29279-2-prudo@linux.ibm.com Fixes: c17187b0b393 ("kernel/kexec_file.c: move purgatories sha256 to common code") Signed-off-by: Philipp Rudo <prudo@linux.ibm.com> Acked-by: Dave Young <dyoung@redhat.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> [4.17+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net/9p/client.c: put refcount of trans_mod in error case in parse_opts()
In my testing, the second mount will fail after umounting successfully.
The reason is that we put refcount of trans_mod in the correct case
rather than the error case in parse_opts() at last. That will cause the
refcount decrease to -1, and when we try to get trans_mod again in
try_module_get(), we could only increase refcount to 0 which will cause
failure as follows:
parse_opts
v9fs_get_trans_by_name
try_module_get : return NULL to caller which cause error
So we should put refcount of trans_mod in error case.
Link: http://lkml.kernel.org/r/5B3F39A0.2030509@huawei.com Fixes: 37198f64738447 ("net/9p/client.c: fix potential refcnt problem of trans module") Signed-off-by: Jun Piao <piaojun@huawei.com> Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com> Reviewed-by: Greg Kurz <groug@kaod.org> Reviewed-by: Dominique Martinet <dominique.martinet@cea.fr> Tested-by: Dominique Martinet <dominique.martinet@cea.fr> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicholas Piggin [Fri, 13 Jul 2018 23:59:03 +0000 (16:59 -0700)]
mm: allow arch to supply p??_free_tlb functions
The mmu_gather APIs keep track of the invalidated address range
including the span covered by invalidated page table pages. Ranges
covered by page tables but not ptes (and therefore no TLBs) still need
to be invalidated because some architectures (x86) can cache
intermediate page table entries, and invalidate those with normal TLB
invalidation instructions to be almost-backward-compatible.
Architectures which don't cache intermediate page table entries, or
which invalidate these caches separately from TLB invalidation, do not
require TLB invalidation range expanded over page tables.
Allow architectures to supply their own p??_free_tlb functions, which
can avoid the __tlb_adjust_range.
Link: http://lkml.kernel.org/r/20180703013131.2807-1-npiggin@gmail.com Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: "Aneesh Kumar K. V" <aneesh.kumar@linux.vnet.ibm.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Nadav Amit <nadav.amit@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tomas Bortoli [Fri, 13 Jul 2018 23:58:59 +0000 (16:58 -0700)]
autofs: fix slab out of bounds read in getname_kernel()
The autofs subsystem does not check that the "path" parameter is present
for all cases where it is required when it is passed in via the "param"
struct.
In particular it isn't checked for the AUTOFS_DEV_IOCTL_OPENMOUNT_CMD
ioctl command.
To solve it, modify validate_dev_ioctl(function to check that a path has
been provided for ioctl commands that require it.
Link: http://lkml.kernel.org/r/153060031527.26631.18306637892746301555.stgit@pluto.themaw.net Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Signed-off-by: Ian Kent <raven@themaw.net> Reported-by: syzbot+60c837b428dc84e83a93@syzkaller.appspotmail.com Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fs/proc/task_mmu.c: fix Locked field in /proc/pid/smaps*
Thomas reports:
"While looking around in /proc on my v4.14.52 system I noticed that all
processes got a lot of "Locked" memory in /proc/*/smaps. A lot more
memory than a regular user can usually lock with mlock().
Commit ce6cd7fa7adf (in v4.14-rc1) seems to have changed the behavior
of "Locked".
Before that commit the code was like this. Notice the VM_LOCKED check.
mm: do not drop unused pages when userfaultd is running
KVM guests on s390 can notify the host of unused pages. This can result
in pte_unused callbacks to be true for KVM guest memory.
If a page is unused (checked with pte_unused) we might drop this page
instead of paging it. This can have side-effects on userfaultd, when
the page in question was already migrated:
The next access of that page will trigger a fault and a user fault
instead of faulting in a new and empty zero page. As QEMU does not
expect a userfault on an already migrated page this migration will fail.
The most straightforward solution is to ignore the pte_unused hint if a
userfault context is active for this VMA.
Link: http://lkml.kernel.org/r/20180703171854.63981-1-borntraeger@de.ibm.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Janosch Frank <frankja@linux.ibm.com> Cc: David Hildenbrand <david@redhat.com> Cc: Cornelia Huck <cohuck@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus, also saw this bug on his machine, and confirmed that reverting
commit 4cf0fbea2757 ("x86/e820: put !E820_TYPE_RAM regions into
memblock.reserved") fixes the issue.
The problem is that we incorrectly zero some struct pages after they
were setup.
The fix is to zero unavailable struct pages prior to initializing of
struct pages.
A more detailed fix should come later that would avoid double zeroing
cases: one in __init_single_page(), the other one in
zero_resv_unavail().
Fixes: 4cf0fbea2757 ("x86/e820: put !E820_TYPE_RAM regions into memblock.reserved") Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"A clocksource driver fix and a revert"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: arm_arch_timer: Set arch_mem_timer cpumask to cpu_possible_mask
Revert "tick: Prefer a lower rating device only if it's CPU local device"
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tool fixes from Ingo Molnar:
"Misc tooling fixes: python3 related fixes, gcc8 fix, bashism fixes and
some other smaller fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Use python-config --includes rather than --cflags
perf script python: Fix dict reference counting
perf stat: Fix --interval_clear option
perf tools: Fix compilation errors on gcc8
perf test shell: Prevent temporary editor files from being considered test scripts
perf llvm-utils: Remove bashism from kernel include fetch script
perf test shell: Make perf's inet_pton test more portable
perf test shell: Replace '|&' with '2>&1 |' to work with more shells
perf scripts python: Add Python 3 support to EventClass.py
perf scripts python: Add Python 3 support to sched-migration.py
perf scripts python: Add Python 3 support to Util.py
perf scripts python: Add Python 3 support to SchedGui.py
perf scripts python: Add Python 3 support to Core.py
perf tools: Generate a Python script compatible with Python 2 and 3
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rseq fixes from Ingo Molnar:
"Various rseq ABI fixes and cleanups: use get_user()/put_user(),
validate parameters and use proper uapi types, etc"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq/selftests: cleanup: Update comment above rseq_prepare_unload
rseq: Remove unused types_32_64.h uapi header
rseq: uapi: Declare rseq_cs field as union, update includes
rseq: uapi: Update uapi comments
rseq: Use get_user/put_user rather than __get_user/__put_user
rseq: Use __u64 for rseq_cs fields, validate user inputs
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Things have been quite slow, only 6 RC patches have been sent to the
list. Regression, user visible bugs, and crashing fixes:
- cxgb4 could wrongly fail MR creation due to a typo
- various crashes if the wrong QP type is mixed in with APIs that
expect other types
- syzkaller oops
- using ERR_PTR and NULL together cases HFI1 to crash in some cases
- mlx5 memory leak in error unwind"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix memory leak in mlx5_ib_create_srq() error path
RDMA/uverbs: Don't fail in creation of multiple flows
IB/hfi1: Fix incorrect mixing of ERR_PTR and NULL return values
RDMA/uverbs: Fix slab-out-of-bounds in ib_uverbs_ex_create_flow
RDMA/uverbs: Protect from attempts to create flows on unsupported QP
iw_cxgb4: correctly enforce the max reg_mr depth
Merge tag 'kbuild-fixes-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- update Kbuild and Kconfig documents
- sanitize -I compiler option handling
- update extract-vmlinux script to recognize LZ4 and ZSTD
- fix tools Makefiles
- update tags.sh to handle __ro_after_init
- suppress warnings in case getconf does not recognize LFS_* parameters
* tag 'kbuild-fixes-v4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: suppress warnings from 'getconf LFS_*'
scripts/tags.sh: add __ro_after_init
tools: build: Use HOSTLDFLAGS with fixdep
tools: build: Fixup host c flags
tools build: fix # escaping in .cmd files for future Make
scripts: teach extract-vmlinux about LZ4 and ZSTD
kbuild: remove duplicated comments about PHONY
kbuild: .PHONY is not a variable, but PHONY is
kbuild: do not drop -I without parameter
kbuild: document the KBUILD_KCONFIG env. variable
kconfig: update user kconfig tools doc.
kbuild: delete INSTALL_FW_PATH from kbuild documentation
kbuild: update ARCH alias info for sparc
kbuild: update ARCH alias info for sh
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Catalin's out enjoying the sunshine, so I'm sending the fixes for a
couple of weeks (although there hopefully won't be any more!).
We've got a revert of a previous fix because it broke the build with
some distro toolchains and a preemption fix when detemining whether or
not the SIMD unit is in use.
Summary:
- Revert back to the 'linux' target for LD, as 'elf' breaks some
distributions
- Fix preemption race when testing whether the vector unit is in use
or not"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: neon: Fix function may_use_simd() return error status
Revert "arm64: Use aarch64elf and aarch64elfb emulation mode variants"
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A couple of small fixes this time around from Steven for an
interaction between ftrace and kernel read-only protection, and
Vladimir for nommu"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8780/1: ftrace: Only set kernel memory back to read-only after boot
ARM: 8775/1: NOMMU: Use instr_sync instead of plain isb in common code
Merge tag 'trace-v4.18-rc3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixlet from Steven Rostedt:
"Joel Fernandes asked to add a feature in tracing that Android had its
own patch internally for. I took it back in 4.13. Now he realizes that
he had a mistake, and swapped the values from what Android had. This
means that the old Android tools will break when using a new kernel
that has the new feature on it.
The options are:
1. To swap it back to what Android wants.
2. Add a command line option or something to do the swap
3. Just let Android carry a patch that swaps it back
Since it requires setting a tracing option to enable this anyway, I
doubt there are other users of this than Android. Thus, I've decided
to take option 1. If someone else is actually depending on the order
that is in the kernel, then we will have to revert this change and go
to option 2 or 3"
* tag 'trace-v4.18-rc3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Reorder display of TGID to be after PID
Merge tag 'sound-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few HD-auio fixes: one fix for a possible mutex deadlock at
HDMI hotplug handling is somewhat subtle and delicate, while the rest
are usual device-specific quirks"
* tag 'sound-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/ca0132: Update a pci quirk device name
ALSA: hda/ca0132: Add Recon3Di quirk for Gigabyte G1.Sniper Z97
ALSA: hda/realtek - two more lenovo models need fixup of MIC_LOCATION
ALSA: hda - Handle pm failure during hotplug
Merge tag 'libnvdimm-fixes-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dave Jiang:
- ensure that a variable passed in by reference to acpi_nfit_ctl is
always set to a value. An incremental patch is provided due to notice
from testing in -next. The rest of the commits did not exhibit
issues.
- fix a return path in nsio_rw_bytes() that was not returning "bytes
remain" as expected for the function.
- address an issue where applications polling on scrub-completion for
the NVDIMM may falsely wakeup and read the wrong state value and
cause hang.
- change the test unit persistent capability attribute to fix up a
broken assumption in the unit test infrastructure wrt the
'write_cache' attribute
- ratelimit dev_info() in the dax device check_vma() function since
this is easily triggered from userspace
* tag 'libnvdimm-fixes-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix unchecked dereference in acpi_nfit_ctl
acpi, nfit: Fix scrub idle detection
tools/testing/nvdimm: advertise a write cache for nfit_test
acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value
dev-dax: check_vma: ratelimit dev_info-s
libnvdimm, pmem: Fix memcpy_mcsafe() return code handling in nsio_rw_bytes()
However Android's trace visualization tools expect a slightly different
format due to an out-of-tree patch patch that was been carried for a
decade, notice that the TGID and CPU fields are reversed:
From kernel v4.13 onwards, during which TGID was introduced, tracing
with systrace on all Android kernels will break (most Android kernels
have been on 4.9 with Android patches, so this issues hasn't been seen
yet). From v4.13 onwards things will break.
The chrome browser's tracing tools also embed the systrace viewer which
uses the legacy TGID format and updates to that are known to be
difficult to make.
Considering this, I suggest we make this change to the upstream kernel
and backport it to all Android kernels. I believe this feature is merged
recently enough into the upstream kernel that it shouldn't be a problem.
Also logically, IMO it makes more sense to group the TGID with the
TASK-PID and the CPU after these.
Link: http://lkml.kernel.org/r/20180626000822.113931-1-joel@joelfernandes.org Cc: jreck@google.com Cc: tkjos@google.com Cc: stable@vger.kernel.org Fixes: 0c3dcda51a41 ("tracing: Add support for display of tgid in trace output") Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Wolfram Sang [Tue, 10 Jul 2018 21:42:15 +0000 (23:42 +0200)]
i2c: recovery: if possible send STOP with recovery pulses
I2C clients may misunderstand recovery pulses if they can't read SDA to
bail out early. In the worst case, as a write operation. To avoid that
and if we can write SDA, try to send STOP to avoid the
misinterpretation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
Suppress warnings for systems that do not recognize LFS_*.
getconf: no such configuration parameter `LFS_CFLAGS'
getconf: no such configuration parameter `LFS_LDFLAGS'
getconf: no such configuration parameter `LFS_LIBS'
Fixes: fd03d2504ecf ("kbuild: Enable Large File Support for hostprogs") Reported-by: Chen Feng <puck.chen@hisilicon.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Laura Abbott [Tue, 10 Jul 2018 00:45:56 +0000 (17:45 -0700)]
tools: build: Fixup host c flags
Commit 8dcae63c7d83 ("tools build: Add support for host programs format")
introduced host_c_flags which referenced CHOSTFLAGS. The actual name of the
variable is HOSTCFLAGS. Fix this up.
Fixes: 8dcae63c7d83 ("tools build: Add support for host programs format") Signed-off-by: Laura Abbott <labbott@redhat.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Adam Ford [Wed, 11 Jul 2018 17:54:54 +0000 (12:54 -0500)]
ARM: dts: am3517.dtsi: Disable reference to OMAP3 OTG controller
The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi. This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.
Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: DRA7/OMAP5: Enable ACTLR[0] (Enable invalidates of BTB) for secondary cores
Call secure services to enable ACTLR[0] (Enable invalidates of BTB with
ICIALLU) when branch hardening is enabled for kernel.
On GP devices OMAP5/DRA7, there is no possibility to update secure
side since "secure world" is ROM and there are no override mechanisms
possible. On HS devices, appropriate PPA should do the workarounds as
well.
However, the configuration is only done for secondary core, since it is
expected that firmware/bootloader will have enabled the required
configuration for the primary boot core (note: bootloaders typically
will NOT enable secondary processors, since it has no need to do so).
Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
xen: remove global bit from __default_kernel_pte_mask for pv guests
When removing the global bit from __supported_pte_mask do the same for
__default_kernel_pte_mask in order to avoid the WARN_ONCE() in
check_pgprot() when setting a kernel pte before having called
init_mem_mapping().
Cc: <stable@vger.kernel.org> # 4.17 Reported-by: Michael Young <m.a.young@durham.ac.uk> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com>
ARM: 8780/1: ftrace: Only set kernel memory back to read-only after boot
Dynamic ftrace requires modifying the code segments that are usually
set to read-only. To do this, a per arch function is called both before
and after the ftrace modifications are performed. The "before" function
will set kernel code text to read-write to allow for ftrace to make the
modifications, and the "after" function will set the kernel code text
back to "read-only" to keep the kernel code text protected.
The issue happens when dynamic ftrace is tested at boot up. The test is
done before the kernel code text has been set to read-only. But the
"before" and "after" calls are still performed. The "after" call will
change the kernel code text to read-only prematurely, and other boot
code that expects this code to be read-write will fail.
The solution is to add a variable that is set when the kernel code text
is expected to be converted to read-only, and make the ftrace "before"
and "after" calls do nothing if that variable is not yet set. This is
similar to the x86 solution from commit 5e691f76602f ("ftrace, x86:
make kernel text writable only for conversions").
Link: http://lkml.kernel.org/r/20180620212906.24b7b66e@vmware.local.home Reported-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Kamal Heib [Tue, 10 Jul 2018 08:56:50 +0000 (11:56 +0300)]
RDMA/mlx5: Fix memory leak in mlx5_ib_create_srq() error path
Fix memory leak in the error path of mlx5_ib_create_srq() by making sure
to free the allocated srq.
Fixes: 88abe80b5270 ("IB/mlx5: Fix integer overflows in mlx5_ib_create_srq") Signed-off-by: Kamal Heib <kamalheib1@gmail.com> Acked-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Merge branch 'for-4.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
- Jens's patches to expand the usable command depth from 31 to 32 broke
sata_fsl due to a subtle command iteration bug. Fixed by introducing
explicit iteration helpers and using the correct variant.
- On some laptops, enabling LPM by default reportedly led to occasional
hard hangs. Blacklist the affected cases.
- Other misc fixes / changes.
* 'for-4.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: Remove depends on HAS_DMA in case of platform dependency
ata: Fix ZBC_OUT all bit handling
ata: Fix ZBC_OUT command block check
ahci: Add Intel Ice Lake LP PCI ID
ahci: Disable LPM on Lenovo 50 series laptops with a too old BIOS
sata_nv: remove redundant pointers sdev0 and sdev1
sata_fsl: remove dead code in tag retrieval
sata_fsl: convert to command iterator
libata: convert eh to command iterators
libata: add command iterator helpers
ata: ahci_mvebu: ahci_mvebu_stop_engine() can be static
libahci: Fix possible Spectre-v1 pmp indexing in ahci_led_store()
sample: vfio-mdev: avoid deadlock in mdev_access()
mdev_access() calls mbochs_get_page() with mdev_state->ops_lock held,
while mbochs_get_page() locks the mutex by itself.
It leads to unavoidable deadlock.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Merge tag 'char-misc-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are a few char/misc driver fixes for 4.18-rc5.
The "largest" stuff here is fixes for the UIO changes in 4.18-rc1 that
caused breakages for some people. Thanks to Xiubo Li for fixing them
quickly. Other than that, minor fixes for thunderbolt, vmw_balloon,
nvmem, mei, ibmasm, and mei drivers. There's also a MAINTAINERS update
where Rafael is offering to help out with reviewing driver core
patches.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
nvmem: Don't let a NULL cell_id for nvmem_cell_get() crash us
thunderbolt: Notify userspace when boot_acl is changed
uio: fix crash after the device is unregistered
uio: change to use the mutex lock instead of the spin lock
uio: use request_threaded_irq instead
fpga: altera-cvp: Fix an error handling path in 'altera_cvp_probe()'
ibmasm: don't write out of bounds in read handler
MAINTAINERS: Add myself as driver core changes reviewer
mei: discard messages from not connected client during power down.
vmw_balloon: fix inflation with batching
Merge tag 'staging-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are two tiny staging driver fixes for reported issues for
4.18-rc5.
One fixes the r8822be driver to properly work on lots of new laptops,
the other is for the rtl8723bs driver to fix an underflow error.
Both have been in linux-next for a while with no reported issues"
* tag 'staging-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8822be: Fix RTL8822be can't find any wireless AP
staging: rtl8723bs: Prevent an underflow in rtw_check_beacon_data().
Merge tag 'usb-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.18-rc5.
Nothing major here, just the normal set of new device ids, xhci fixes,
and some typec fixes. The typec fix required some tiny changes in an
i2c driver, which that maintainer acked to come through my tree.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: yurex: fix out-of-bounds uaccess in read handler
usb: quirks: add delay quirks for Corsair Strafe
xhci: xhci-mem: off by one in xhci_stream_id_to_ring()
usb/gadget: aspeed-vhub: add USB_LIBCOMPOSITE dependency
docs: kernel-parameters.txt: document xhci-hcd.quirks parameter
USB: serial: mos7840: fix status-register error handling
USB: serial: keyspan_pda: fix modem-status error handling
USB: serial: cp210x: add another USB ID for Qivicon ZigBee stick
USB: serial: ch341: fix type promotion bug in ch341_control_in()
i2c-cht-wc: Fix bq24190 supplier
typec: tcpm: Correctly report power_supply current and voltage for non pd supply
usb: xhci: dbc: Don't decrement runtime PM counter if DBC is not started
Merge tag 'mmc-v4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fixup devname in /proc/interrupts for card detect GPIO
MMC host:
- sdhci-esdhc-imx: Allow 1.8V speed-modes without 100/200MHz pinctrls
- sunxi: Disable IRQ in low power state to prevent IRQ storm
- dw_mmc: Fix card threshold control configuration
- renesas_sdhi_internal_dmac: Fixup DMA error paths"
* tag 'mmc-v4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-esdhc-imx: allow 1.8V modes without 100/200MHz pinctrl states
mmc: sunxi: Disable irq during pm_suspend
mmc: dw_mmc: fix card threshold control configuration
mmc: core: cd_label must be last entry of mmc_gpio struct
mmc: renesas_sdhi_internal_dmac: Cannot clear the RX_IN_USE in abort
mmc: renesas_sdhi_internal_dmac: Fix missing unmap in error patch
Merge tag 'acpi-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Address a regression in ACPICA that ceased to clear the status of GPEs
and fixed events before entering the ACPI S5 (off) system state during
the 4.17 cycle which caused some systems to power up immediately after
they had been turned off"
* tag 'acpi-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Clear status of all events when entering S5
arm64: neon: Fix function may_use_simd() return error status
It does not matter if the caller of may_use_simd() migrates to
another cpu after the call, but it is still important that the
kernel_neon_busy percpu instance that is read matches the cpu the
task is running on at the time of the read.
This means that raw_cpu_read() is not sufficient. kernel_neon_busy
may appear true if the caller migrates during the execution of
raw_cpu_read() and the next task to be scheduled in on the initial
cpu calls kernel_neon_begin().
This patch replaces raw_cpu_read() with this_cpu_read() to protect
against this race.
Cc: <stable@vger.kernel.org> Fixes: b06e6ffad596 ("arm64: neon: Remove support for nested or hardirq kernel-mode NEON") Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: Dave Martin <Dave.Martin@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Yandong Zhao <yandong77520@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Tony Battersby [Wed, 11 Jul 2018 14:46:03 +0000 (10:46 -0400)]
bsg: fix bogus EINVAL on non-data commands
Fix a regression introduced in Linux kernel 4.17 where sending a SCSI
command that does not transfer data (such as TEST UNIT READY) via
/dev/bsg/* results in EINVAL.
Fixes: a54164822a8c ("bsg: split handling of SCSI CDBs vs transport requeues") Cc: <stable@vger.kernel.org> # 4.17+ Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jeremy Cline [Tue, 10 Jul 2018 15:46:12 +0000 (11:46 -0400)]
perf tools: Use python-config --includes rather than --cflags
Builds started failing in Fedora on Python 3.7 with:
`.gnu.debuglto_.debug_macro' referenced in section
`.gnu.debuglto_.debug_macro' of
util/scripting-engines/trace-event-python.o: defined in discarded
section
In Fedora, Python 3.7 added -flto to the list of --cflags and since it
was only applied to util/scripting-engines/trace-event-python.c and
scripts/python/Perf-Trace-Util/Context.c, linking failed.
It's not the first time the addition of flags has broken builds: commit ab98d0192b21 ("perf tools: Fix up build in hardnened environments")
appears to have fixed a similar problem. "python-config --includes"
provides the proper -I flags and doesn't introduce additional CFLAGS.
Signed-off-by: Jeremy Cline <jcline@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180710154612.6285-1-jcline@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Janne Huttunen [Mon, 9 Jul 2018 10:59:50 +0000 (13:59 +0300)]
perf script python: Fix dict reference counting
The dictionaries are attached to the parameter tuple that steals the
references and takes care of releasing them when appropriate. The code
should not decrement the reference counts explicitly. E.g. if libpython
has been built with reference debugging enabled, the superfluous DECREFs
will trigger this error when running perf script:
Fatal Python error: Objects/tupleobject.c:238 object at
0x7f10f2041b40 has negative ref count -1
Aborted (core dumped)
If the reference debugging is not enabled, the superfluous DECREFs might
cause the dict objects to be silently released while they are still in
use. This may trigger various other assertions or just cause perf
crashes and/or weird and unexpected data changes in the stored Python
objects.
Signed-off-by: Janne Huttunen <janne.huttunen@nokia.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jaroslav Skarvada <jskarvad@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1531133990-17485-1-git-send-email-janne.huttunen@nokia.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jiri Olsa [Mon, 2 Jul 2018 13:42:01 +0000 (15:42 +0200)]
perf tools: Fix compilation errors on gcc8
We are getting following warnings on gcc8 that break compilation:
$ make
CC jvmti/jvmti_agent.o
jvmti/jvmti_agent.c: In function ‘jvmti_open’:
jvmti/jvmti_agent.c:252:35: error: ‘/jit-’ directive output may be truncated \
writing 5 bytes into a region of size between 1 and 4096 [-Werror=format-truncation=]
snprintf(dump_path, PATH_MAX, "%s/jit-%i.dump", jit_path, getpid());
There's no point in checking the result of snprintf call in
jvmti_open, the following open call will fail in case the
name is mangled or too long.
Using tools/lib/ function scnprintf that touches the return value from
the snprintf() calls and thus get rid of those warnings.
$ make DEBUG=1
CC arch/x86/util/perf_regs.o
arch/x86/util/perf_regs.c: In function ‘arch_sdt_arg_parse_op’:
arch/x86/util/perf_regs.c:229:4: error: ‘strncpy’ output truncated before terminating nul
copying 2 bytes from a string of the same length [-Werror=stringop-truncation]
strncpy(prefix, "+0", 2);
^~~~~~~~~~~~~~~~~~~~~~~~
Using scnprintf instead of the strncpy (which we know is safe in here)
to get rid of that warning.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: David Ahern <dsahern@gmail.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/20180702134202.17745-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kim Phillips [Fri, 29 Jun 2018 17:46:58 +0000 (12:46 -0500)]
perf test shell: Prevent temporary editor files from being considered test scripts
Allows a perf shell test developer to concurrently edit and run their
test scripts, avoiding perf test attempts to execute their editor
temporary files, such as seen here:
Signed-off-by: Kim Phillips <kim.phillips@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sandipan Das <sandipan@linux.vnet.ibm.com> Cc: Thomas Richter <tmricht@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/20180629124658.15a506b41fc4539c08eb9426@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kim Phillips [Fri, 29 Jun 2018 17:46:52 +0000 (12:46 -0500)]
perf llvm-utils: Remove bashism from kernel include fetch script
Like system(), popen() calls /bin/sh, which may/may not be bash.
Script when run on dash and encounters the line, yields:
exit: Illegal number: -1
checkbashisms report on script content:
possible bashism (exit|return with negative status code):
exit -1
Remove the bashism and use the more portable non-zero failure
status code 1.
Signed-off-by: Kim Phillips <kim.phillips@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sandipan Das <sandipan@linux.vnet.ibm.com> Cc: Thomas Richter <tmricht@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/20180629124652.8d0af7e2281fd3fd8262cacc@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kim Phillips [Fri, 29 Jun 2018 17:46:43 +0000 (12:46 -0500)]
perf test shell: Make perf's inet_pton test more portable
Debian based systems such as Ubuntu have dash as their default shell.
Even if the normal or root user's shell is bash, certain scripts still
call /bin/sh, which points to dash, so we fix this perf test by
rewriting it in a more portable way.
BEFORE:
$ sudo perf test -v 64
64: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 31942
./tests/shell/record+probe_libc_inet_pton.sh: 18: ./tests/shell/record+probe_libc_inet_pton.sh: expected[0]=ping[][0-9 \.:]+probe_libc:inet_pton: \([[:xdigit:]]+\): not found
./tests/shell/record+probe_libc_inet_pton.sh: 19: ./tests/shell/record+probe_libc_inet_pton.sh: expected[1]=.*inet_pton\+0x[[:xdigit:]]+[[:space:]]\(/lib/x86_64-linux-gnu/libc-2.27.so|inlined\)$: not found
./tests/shell/record+probe_libc_inet_pton.sh: 29: ./tests/shell/record+probe_libc_inet_pton.sh: expected[2]=getaddrinfo\+0x[[:xdigit:]]+[[:space:]]\(/lib/x86_64-linux-gnu/libc-2.27.so\)$: not found
./tests/shell/record+probe_libc_inet_pton.sh: 30: ./tests/shell/record+probe_libc_inet_pton.sh: expected[3]=.*\+0x[[:xdigit:]]+[[:space:]]\(.*/bin/ping.*\)$: not found
ping 31963 [004] 83577.670613: probe_libc:inet_pton: (7fe15f87f4b0)
./tests/shell/record+probe_libc_inet_pton.sh: 39: ./tests/shell/record+probe_libc_inet_pton.sh: Bad substitution
./tests/shell/record+probe_libc_inet_pton.sh: 41: ./tests/shell/record+probe_libc_inet_pton.sh: Bad substitution
test child finished with -2
---- end ----
probe libc's inet_pton & backtrace it with ping: Skip
AFTER:
$ sudo perf test -v 64
64: probe libc's inet_pton & backtrace it with ping :
--- start ---
test child forked, pid 32277
ping 32295 [001] 83679.690020: probe_libc:inet_pton: (7ff244f504b0) 7ff244f504b0 __GI___inet_pton+0x0 (/lib/x86_64-linux-gnu/libc-2.27.so) 7ff244f14ce4 getaddrinfo+0x124 (/lib/x86_64-linux-gnu/libc-2.27.so) 556ac036b57d _init+0xb75 (/bin/ping)
test child finished with 0
---- end ----
probe libc's inet_pton & backtrace it with ping: Ok
Signed-off-by: Kim Phillips <kim.phillips@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sandipan Das <sandipan@linux.vnet.ibm.com> Cc: Thomas Richter <tmricht@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/20180629124643.2089b3ce59960eba34e87b27@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Kim Phillips [Fri, 29 Jun 2018 17:46:33 +0000 (12:46 -0500)]
perf test shell: Replace '|&' with '2>&1 |' to work with more shells
Since we do not specify bash (and/or zsh) as a requirement, use the
standard error redirection that is more widely supported.
BEFORE:
$ sudo perf test -v 62
62: Check open filename arg using perf trace + vfs_getname:
--- start ---
test child forked, pid 27305
./tests/shell/trace+probe_vfs_getname.sh: 20: ./tests/shell/trace+probe_vfs_getname.sh: Syntax error: "&" unexpected
test child finished with -2
---- end ----
Check open filename arg using perf trace + vfs_getname: Skip
AFTER:
$ sudo perf test -v 62
64: Check open filename arg using perf trace + vfs_getname :
--- start ---
test child forked, pid 23008
Added new event:
probe:vfs_getname (on getname_flags:72 with pathname=result->name:string)
You can now use it in all perf tools, such as:
perf record -e probe:vfs_getname -aR sleep 1
0.361 ( 0.008 ms): touch/23032 openat(dfd: CWD, filename: /tmp/temporary_file.VEh0n, flags: CREAT|NOCTTY|NONBLOCK|WRONLY, mode: IRUGO|IWUGO) = 4
test child finished with 0
---- end ----
Check open filename arg using perf trace + vfs_getname: Ok
Similar to commit 50ef5f304b4c, with the same title.
Signed-off-by: Kim Phillips <kim.phillips@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sandipan Das <sandipan@linux.vnet.ibm.com> Cc: Thomas Richter <tmricht@linux.vnet.ibm.com> Link: http://lkml.kernel.org/r/20180629124633.0a9f4bea54b8d2c28f265de2@arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jeremy Cline [Tue, 8 May 2018 21:27:46 +0000 (21:27 +0000)]
perf scripts python: Add Python 3 support to Util.py
Support both Python 2 and Python 3 in Util.py. The dict class no longer
has a ``has_key`` method and print is now a function rather than a
statement. This should have no functional change.
Signed-off-by: Jeremy Cline <jeremy@jcline.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Herton Krzesinski <herton@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/0100016341a730c6-8db8b9b1-da2d-4ee3-96bf-47e0ae9796bd-000000@email.amazonses.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jeremy Cline [Tue, 8 May 2018 21:27:43 +0000 (21:27 +0000)]
perf tools: Generate a Python script compatible with Python 2 and 3
When generating a Python script with "perf script -g python", produce
one that is compatible with Python 2 and 3. The difference between the
two generated scripts is:
--- python2-perf-script.py 2018-05-08 15:35:00.865889705 -0400
+++ python3-perf-script.py 2018-05-08 15:34:49.019789564 -0400
@@ -7,6 +7,8 @@
# be retrieved using Python functions of the form common_*(context).
# See the perf-script-python Documentation for the list of available functions.
+from __future__ import print_function
+
import os
import sys
@@ -18,10 +20,10 @@
def trace_begin():
- print "in trace_begin"
+ print("in trace_begin")
def trace_end():
- print "in trace_end"
+ print("in trace_end")
efi/x86: Fix mixed mode reboot loop by removing pointless call to PciIo->Attributes()
Hans de Goede reported that his mixed EFI mode Bay Trail tablet
would not boot at all any more, but enter a reboot loop without
any logs printed by the kernel.
Unbreak 64-bit Linux/x86 on 32-bit UEFI:
When it was first introduced, the EFI stub code that copies the
contents of PCI option ROMs originally only intended to do so if
the EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM attribute was *not* set.
The reason was that the UEFI spec permits PCI option ROM images
to be provided by the platform directly, rather than via the ROM
BAR, and in this case, the OS can only access them at runtime if
they are preserved at boot time by copying them from the areas
described by PciIo->RomImage and PciIo->RomSize.
However, it implemented this check erroneously, as can be seen in
commit:
f5e16a7d5c97d ("EFI: Stash ROMs if they're not in the PCI BAR")
which introduced:
if (!attributes & EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM)
continue;
and given that the numeric value of EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM
is 0x4000, this condition never becomes true, and so the option ROMs
were copied unconditionally.
This was spotted and 'fixed' by commit:
61a66af064b656c67 ("x86, efi: correct precedence of operators in setup_efi_pci")
but inadvertently inverted the logic at the same time, defeating
the purpose of the code, since it now only preserves option ROM
images that can be read from the ROM BAR as well.
Unsurprisingly, this broke some systems, and so the check was removed
entirely in the following commit:
2d4513759328 ("x86, efi: remove attribute check from setup_efi_pci")
It is debatable whether this check should have been included in the
first place, since the option ROM image provided to the UEFI driver by
the firmware may be different from the one that is actually present in
the card's flash ROM, and so whatever PciIo->RomImage points at should
be preferred regardless of whether the attribute is set.
As this was the only use of the attributes field, we can remove
the call to PciIo->Attributes() entirely, which is especially
nice because its prototype involves uint64_t type by-value
arguments which the EFI mixed mode has trouble dealing with.
Any mixed mode system with PCI is likely to be affected.
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de> Tested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20180711090235.9327-2-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Vladimir Murzin [Mon, 18 Jun 2018 13:33:03 +0000 (14:33 +0100)]
ARM: 8775/1: NOMMU: Use instr_sync instead of plain isb in common code
Greg reported that commit 4650d85e32f59 ("ARM: 8756/1: NOMMU: Postpone
MPU activation till __after_proc_init") is causing breakage for the
old Versatile platform in no-MMU mode (with out-of-tree patches):
AS arch/arm/kernel/head-nommu.o
arch/arm/kernel/head-nommu.S: Assembler messages:
arch/arm/kernel/head-nommu.S:180: Error: selected processor does not support `isb' in ARM mode
scripts/Makefile.build:417: recipe for target 'arch/arm/kernel/head-nommu.o' failed
make[2]: *** [arch/arm/kernel/head-nommu.o] Error 1
Makefile:1034: recipe for target 'arch/arm/kernel' failed
make[1]: *** [arch/arm/kernel] Error 2
Since the code is common for all NOMMU builds usage of the isb was a
bad idea (please, note that isb also used in MPU related code which is
fine because MPU has dependency on CPU_V7/CPU_V7M), instead use more
robust instr_sync assembler macro.
Fixes: 4650d85e32f5 ("ARM: 8756/1: NOMMU: Postpone MPU activation till __after_proc_init") Reported-by: Greg Ungerer <gerg@kernel.org> Tested-by: Greg Ungerer <gerg@kernel.org> Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Merge tag 'mips_fixes_4.18_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A couple more MIPS fixes for 4.18:
- Use async IPIs for arch_trigger_cpumask_backtrace() in order to
avoid warnings & deadlocks, fixing a problem introduced in v3.19
with the fix trivial to backport as far as v4.9.
- Fix ioremap()'s MMU/TLB backed path to avoid spuriously rejecting
valid requests due to an incorrect belief that the memory region is
backed by potentially-in-use RAM. This fixes a regression in v4.2"
* tag 'mips_fixes_4.18_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Fix ioremap() RAM check
MIPS: Use async IPIs for arch_trigger_cpumask_backtrace()
MIPS: Call dump_stack() from show_regs()
rseq as it was merged does not have rseq_finish_*() in the user-space
selftests anymore. Update the rseq_prepare_unload() helper comment to
adapt to this reality.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-api@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Watson <davejwatson@fb.com> Cc: Paul Turner <pjt@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Chris Lameter <cl@linux.com> Cc: Ben Maurer <bmaurer@fb.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Joel Fernandes <joelaf@google.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20180709195155.7654-7-mathieu.desnoyers@efficios.com
rseq: uapi: Declare rseq_cs field as union, update includes
Declaring the rseq_cs field as a union between __u64 and two __u32
allows both 32-bit and 64-bit kernels to read the full __u64, and
therefore validate that a 32-bit user-space cleared the upper 32
bits, thus ensuring a consistent behavior between native 32-bit
kernels and 32-bit compat tasks on 64-bit kernels.
Check that the rseq_cs value read is < TASK_SIZE.
The asm/byteorder.h header needs to be included by rseq.h, now
that it is not using linux/types_32_64.h anymore.
Considering that only __32 and __u64 types are declared in linux/rseq.h,
the linux/types.h header should always be included for both kernel and
user-space code: including stdint.h is just for u64 and u32, which are
not used in this header at all.
Use copy_from_user()/clear_user() to interact with a 64-bit field,
because arm32 does not implement 64-bit __get_user, and ppc32 does not
64-bit get_user. Considering that the rseq_cs pointer does not need to
be loaded/stored with single-copy atomicity from the kernel anymore, we
can simply use copy_from_user()/clear_user().
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-api@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Watson <davejwatson@fb.com> Cc: Paul Turner <pjt@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Chris Lameter <cl@linux.com> Cc: Ben Maurer <bmaurer@fb.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Joel Fernandes <joelaf@google.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20180709195155.7654-5-mathieu.desnoyers@efficios.com
Update rseq uapi header comments to reflect that user-space need to do
thread-local loads/stores from/to the struct rseq fields.
As a consequence of this added requirement, the kernel does not need
to perform loads/stores with single-copy atomicity.
Update the comment associated to the "flags" fields to describe
more accurately that it's only useful to facilitate single-stepping
through rseq critical sections with debuggers.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-api@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Watson <davejwatson@fb.com> Cc: Paul Turner <pjt@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Chris Lameter <cl@linux.com> Cc: Ben Maurer <bmaurer@fb.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Joel Fernandes <joelaf@google.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20180709195155.7654-4-mathieu.desnoyers@efficios.com
rseq: Use get_user/put_user rather than __get_user/__put_user
__get_user()/__put_user() is used to read values for address ranges that
were already checked with access_ok() on rseq registration.
It has been recognized that __get_user/__put_user are optimizing the
wrong thing. Replace them by get_user/put_user across rseq instead.
If those end up showing up in benchmarks, the proper approach would be to
use user_access_begin() / unsafe_{get,put}_user() / user_access_end()
anyway.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-api@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Watson <davejwatson@fb.com> Cc: Paul Turner <pjt@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Chris Lameter <cl@linux.com> Cc: Ben Maurer <bmaurer@fb.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Joel Fernandes <joelaf@google.com> Cc: linux-arm-kernel@lists.infradead.org Link: https://lkml.kernel.org/r/20180709195155.7654-3-mathieu.desnoyers@efficios.com
rseq: Use __u64 for rseq_cs fields, validate user inputs
Change the rseq ABI so rseq_cs start_ip, post_commit_offset and abort_ip
fields are seen as 64-bit fields by both 32-bit and 64-bit kernels rather
that ignoring the 32 upper bits on 32-bit kernels. This ensures we have a
consistent behavior for a 32-bit binary executed on 32-bit kernels and in
compat mode on 64-bit kernels.
Validating the value of abort_ip field to be below TASK_SIZE ensures the
kernel don't return to an invalid address when returning to userspace
after an abort. I don't fully trust each architecture code to consistently
deal with invalid return addresses.
Validating the value of the start_ip and post_commit_offset fields
prevents overflow on arithmetic performed on those values, used to
check whether abort_ip is within the rseq critical section.
If validation fails, the process is killed with a segmentation fault.
When the signature encountered before abort_ip does not match the expected
signature, return -EINVAL rather than -EPERM to be consistent with other
input validation return codes from rseq_get_rseq_cs().
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-api@vger.kernel.org Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com> Cc: Boqun Feng <boqun.feng@gmail.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Watson <davejwatson@fb.com> Cc: Paul Turner <pjt@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Chris Lameter <cl@linux.com> Cc: Ben Maurer <bmaurer@fb.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Cc: Joel Fernandes <joelaf@google.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Link: https://lkml.kernel.org/r/20180709195155.7654-2-mathieu.desnoyers@efficios.com
clocksource: arm_arch_timer: Set arch_mem_timer cpumask to cpu_possible_mask
Currently, arch_mem_timer cpumask is set to cpu_all_mask which should be
fine. However, cpu_possible_mask is more accurate and if there are other
clockevent source in the system which are set to cpu_possible_mask, then
having cpu_all_mask may result in issue.
E.g. on a platform with arm,sp804 timer with rating 300 and
cpu_possible_mask and this arch_mem_timer timer with rating 400 and
cpu_all_mask, tick_check_preferred may choose both preferred as the
cpumasks are not equal though they must be.
This issue was root caused incorrectly initially and a fix was merged as
commit 7451807a30cc ("tick: Prefer a lower rating device only if it's CPU
local device").
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Link: https://lkml.kernel.org/r/1531151136-18297-2-git-send-email-sudeep.holla@arm.com
The original issue was not because of incorrect checking of cpumask for
both new and old tick device. It was incorrectly analysed was due to the
misunderstanding of the comment and misinterpretation of the return value
from tick_check_preferred. The main issue is with the clockevent driver
that sets the cpumask to cpu_all_mask instead of cpu_possible_mask.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Marc Zyngier <marc.zyngier@arm.com> Link: https://lkml.kernel.org/r/1531151136-18297-1-git-send-email-sudeep.holla@arm.com
Merge tag 'drm-fixes-2018-07-10' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This just contains some etnaviv fixes and a MAINTAINERS update for the
new drm tree locations"
* tag 'drm-fixes-2018-07-10' of git://anongit.freedesktop.org/drm/drm:
MAINTAINERS: update drm tree
drm/etnaviv: bring back progress check in job timeout handler
drm/etnaviv: Fix driver unregistering
drm/etnaviv: Check for platform_device_register_simple() failure
Distributions such as Fedora and Debian do not package the ELF linker
scripts with their toolchains, resulting in kernel build failures such
as:
| CHK include/generated/compile.h
| LD [M] arch/arm64/crypto/sha512-ce.o
| aarch64-linux-gnu-ld: cannot open linker script file ldscripts/aarch64elf.xr: No such file or directory
| make[1]: *** [scripts/Makefile.build:530: arch/arm64/crypto/sha512-ce.o] Error 1
| make: *** [Makefile:1029: arch/arm64/crypto] Error 2
Revert back to the linux targets for now, adding a comment to the Makefile
so we don't accidentally break this in the future.
Cc: Paul Kocialkowski <contact@paulk.fr> Cc: <stable@vger.kernel.org> Fixes: d51fa8e65e1b ("arm64: Use aarch64elf and aarch64elfb emulation mode variants") Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
Dave Airlie [Tue, 10 Jul 2018 00:45:04 +0000 (10:45 +1000)]
Merge branch 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux into drm-fixes
Lucas wrote:
"a couple of small fixes:
- 2 patches from Fabio to fix module reloading
- one patch to fix a userspace visible regression, where the job
timeout is a bit too eager and kills legitimate jobs"
Update my TDA998x HDMI encoder MAINTAINERS entry to include the
dt-bindings header, and a keyword pattern to catch patches containing
the DT compatible. Also change the status to "maintained" rather than
"supported".
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jon Hunter [Tue, 3 Jul 2018 08:55:43 +0000 (09:55 +0100)]
i2c: tegra: Fix NACK error handling
On Tegra30 Cardhu the PCA9546 I2C mux is not ACK'ing I2C commands on
resume from suspend (which is caused by the reset signal for the I2C
mux not being configured correctl). However, this NACK is causing the
Tegra30 to hang on resuming from suspend which is not expected as we
detect NACKs and handle them. The hang observed appears to occur when
resetting the I2C controller to recover from the NACK.
Commit c9f7f1c374e4 ("i2c: tegra: proper handling of error cases") added
additional error handling for some error cases including NACK, however,
it appears that this change conflicts with an early fix by commit 4b020a4d92d5 ("i2c: tegra: Add delay before resetting the controller
after NACK"). After commit c9f7f1c374e4 was made we now disable 'packet
mode' before the delay from commit 4b020a4d92d5 happens. Testing shows
that moving the delay to before disabling 'packet mode' fixes the hang
observed on Tegra30. The delay was added to give the I2C controller
chance to send a stop condition and so it makes sense to move this to
before we disable packet mode. Please note that packet mode is always
enabled for Tegra.
Fixes: c9f7f1c374e4 ("i2c: tegra: proper handling of error cases") Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@vger.kernel.org
uref->field_index, uref->usage_index, finfo.field_index and cinfo.index can be
indirectly controlled by user-space, hence leading to a potential exploitation
of the Spectre variant 1 vulnerability.
Fix this by sanitizing such structure fields before using them to index
report->field, field->usage and hid->collection
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Jason Andryuk [Fri, 22 Jun 2018 16:25:49 +0000 (12:25 -0400)]
HID: i2c-hid: Fix "incomplete report" noise
Commit ec9861c6a0bf ("HID: i2c-hid: fix size check and type usage") started
writing messages when the ret_size is <= 2 from i2c_master_recv. However, my
device i2c-DLL07D1 returns 2 for a short period of time (~0.5s) after I stop
moving the pointing stick or touchpad. It varies, but you get ~50 messages
each time which spams the log hard.
Only print the message when ret_size is totally invalid and less than 2 to cut
down on the log spam.
Fixes: ec9861c6a0bf ("HID: i2c-hid: fix size check and type usage") Reported-by: John Smith <john-s-84@gmx.net> Cc: stable@vger.kernel.org Signed-off-by: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stefan Agner [Wed, 4 Jul 2018 15:07:45 +0000 (17:07 +0200)]
mmc: sdhci-esdhc-imx: allow 1.8V modes without 100/200MHz pinctrl states
If pinctrl nodes for 100/200MHz are missing, the controller should
not select any mode which need signal frequencies 100MHz or higher.
To prevent such speed modes the driver currently uses the quirk flag
SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V
signaling is required for all faster modes and slower modes use 3.3V
signaling only.
However, there are eMMC modes which use 1.8V signaling and run below
100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this
mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply
the stack has no valid mode to use. In this tenuous situation the
kernel continuously prints voltage switching errors:
mmc1: Switching to 3.3V signalling voltage failed
Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by
altering the SDHCI capability register. With that the stack is able
to select 1.8V modes even if no faster pinctrl states are available:
# cat /sys/kernel/debug/mmc1/ios
...
timing spec: 8 (mmc DDR52)
signal voltage: 1 (1.80 V)
...
Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch Signed-off-by: Stefan Agner <stefan@agner.ch> Fixes: 33edb9877c73 ("mmc: sdhci-esdhc-imx: change pinctrl state according
to uhs mode") Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
projects / kernel.git / log