phy: marvell: cp110: let the firmware configure the comphy
Replace all comphy initialization with appropriate smc calls. It will
result with triggering synchronous exception that is handled by Secure
Monitor code in EL3. Then the Secure Monitor code will dispatch each smc
call (by parsing the smc function identifier) and triggers appropriate
comphy initialization.
This patch reworks serdes handling for: SATA, SGMII, HS-SGMII and SFI
interfaces.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com> Reviewed-by: Igal Liberman <igall@marvell.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Pratyush Yadav [Fri, 16 Oct 2020 10:46:35 +0000 (16:16 +0530)]
cmd: Add a mux command
This command lets the user list, select, and deselect mux controllers
introduced with the mux framework on the fly. It has 3 subcommands:
list, select, and deselect.
List: Lists all the mux present on the system. The muxes are listed for
each chip. The chip is identified by its device name. Each chip can have
a number of mux controllers. Each is listed in sequence and is assigned
a sequential ID based on its position in the mux chip. It lists details
like ID, whether the mux is currently selected or not, the current
state, the idle state, and the number of states.
A sample output would look something like:
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no unknown as-is 0x4
1 no 0x2 0x2 0x10
2 no 0x73 0x73 0x100
another-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x2 0x2 0x4
Select: Selects a given mux and puts it in the specified state. This
subcommand takes 3 arguments: mux chip, mux ID, state to set
the mux in. The arguments mux chip and mux ID are used to identify which
mux needs to be selected, and then it is selected to the given state.
The mux needs to be deselected before it can be selected again in
another state. The state should be a hexadecimal number.
For example:
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x1 0x1 0x4
=> mux select a-mux-controller 0 0x3
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 yes 0x3 0x1 0x4
1 no 0x1 0x1 0x4
Deselect: Deselects a given mux and puts it in its idle state. This
subcommand takes 2 arguments: the mux chip and mux ID to identify which
mux needs to be deselected. So in the above example, we can deselect mux
0 using:
=> mux deselect a-mux-controller 0
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x1 0x1 0x4
Signed-off-by: Pratyush Yadav <p.yadav@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Provide tests to check the behavior of the multiplexer framework.
Two sets of tests are added. One is using an emulated multiplexer driver
that can be used to test basic functionality like select, deselect, etc.
The other is using the mmio mux which adds tests specific to it.
This adds a driver for mmio-based syscon multiplexers controlled by
bitfields in a syscon register range.
This is heavily based on the linux mmio-mux driver.
drivers: Add a new framework for multiplexer devices
Add a new subsystem that handles multiplexer controllers. The API is the
same as in Linux.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[trini: Update some error calls to use different functions or pass
correct arguments] Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 28 Oct 2020 12:35:28 +0000 (08:35 -0400)]
Merge tag 'efi-2021-01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc2
A software RTC driver is supplied for UEFI SCT testing.
The following UEFI related bugs are fixed:
* correct handling of daylight saving time in GetTime() and SetTime()
* handling of the gd register in function tracing on RISC-V
* disable U-Boot devices in ExitBootServices()
Ilias Apalodimas [Wed, 21 Oct 2020 22:04:21 +0000 (01:04 +0300)]
efi_loader: Disable devices before handing over control
U-Boot Driver Model is supposed to remove devices with either
DM_REMOVE_ACTIVE_DMA or DM_REMOVE_OS_PREPARE flags set, before exiting.
Our bootm command does that by explicitly calling calling
"dm_remove_devices_flags(DM_REMOVE_ACTIVE_ALL);" and we also disable any
USB devices.
The EFI equivalent is doing none of those at the moment. As a result
probing an fTPM driver now renders it unusable in Linux. During our
(*probe) callback we open a session with OP-TEE, which is supposed to
close with our (*remove) callback. Since the (*remove) is never called,
once we boot into Linux and try to probe the device again we are getting
a busy error response. Moreover all uclass (*preremove) functions won't
run.
So let's fix this by mimicking what bootm does and disconnect devices
when efi_exit_boot_services() is called.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
An UEFI application may change the value of the register that gd lives in.
But some of our functions like get_ticks() access this register. So we
have to set the gd register to the U-Boot value when entering a trace
point and set it back to the application value when exiting the trace
point.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On a board without hardware clock this software real time clock can be
used. The build time is used to initialize the RTC. So you will have
to adjust the time either manually using the 'date' command or use
the 'sntp' to update the RTC with the time from a network time server.
See CONFIG_CMD_SNTP and CONFIG_BOOTP_NTPSERVER. The RTC time is
advanced according to CPU ticks.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Makefile: provide constant with seconds since epoch
Provide a constant U_BOOT_EPOCH with the number of seconds since
1970-01-01. This constant can be used to initialize a software
real time clock until it is updated via the 'sntp' command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some drivers use macro pr_cont() for continuing a message sent via printk.
Hence if we want to convert printk messaging to using the logging system,
we must support continuation of log messages too.
As pr_cont() does not provide a message level we need a means of
remembering the last log level.
With the patch a pseudo log level LOGL_CONT as well as a pseudo log
category LOGC_CONT are introduced. Using these results in the application
of the same log level and category as in the previous log message.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 26 Oct 2020 12:25:37 +0000 (08:25 -0400)]
Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-riscv
- No need to check before free in kendryte clk.
- Only enable OF_BOARD_FIXUP if U-Boot is configured for S-Mode.
- Reduce k210 dts DMA block size
- Move timers into drivers/timer
- Correct fu540 dts reg size of clint node
Sean Anderson [Mon, 26 Oct 2020 01:46:58 +0000 (21:46 -0400)]
riscv: Move timer portions of SiFive CLINT to drivers/timer
Half of this driver is a DM-based timer driver, and half is RISC-V-specific
IPI code. Move the timer portions in with the other timer drivers. The
KConfig is not moved, since it also enables IPIs. It could also be split
into two configs, but no boards use the timer but not the IPI atm, so I
haven't split it.
Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Rick Chen <rick@andestech.com>
Sean Anderson [Mon, 12 Oct 2020 18:18:15 +0000 (14:18 -0400)]
riscv: k210: Reduce DMA block size
Although the max DMA size supported by the hardware register is 22 bits (or
4M), the Linux driver for this device only supports transfers of up to 2M.
On a device with 8M total memory, I don't think it will make too much of a
difference.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com> Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
Sean Anderson [Sat, 5 Sep 2020 13:22:11 +0000 (09:22 -0400)]
riscv: Only enable OF_BOARD_FIXUP for S-Mode
It is unsafe to enable OF_BOARD_FIXUP only based on OF_SEPARATE.
OF_SEPARATE may indicate that the user wishes U-Boot to use a different
device tree than one obtained via OF_PRIOR_STAGE. However, OF_SEPARATE may
also indicate that the device tree which would be obtained via
OF_PRIOR_STAGE is invalid, nonexistant, or otherwise unusable. In this
latter case, enabling OF_BOARD_FIXUP will result in corruption of the
device tree. To remedy this, only enable OF_BOARD_FIXUP if U-Boot is
configured for S-Mode.
Fixes: e01f8fd3ef16f478cffc332171fae0e045ce62fe Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Leo Liang <ycliang@andestech.com>
Tom Rini [Sat, 24 Oct 2020 14:49:28 +0000 (10:49 -0400)]
Merge branch '2020-10-23-misc-changes'
Highlights:
- Fix a problem with the bootm overlap tests
- Remove duplicated code in fatwrite
- Cleanup our current "misc" command code and add a new one for misc
class devices.
- Various GPIO fixes
Jaehoon Chung [Wed, 21 Oct 2020 05:17:03 +0000 (14:17 +0900)]
bootm: fix wrong conditions about images overlap
It doesn't need to consider start byte address.
If ramdisk size is 0x800000 and start address is 0x2700000, then it's
used until 0x02efffff, not 0x02f00000. But it's detected to overlapt RD
image, when kernel start address is 0x02f00000.
Because it's doing wrong calculation about rd_len.
This patch fixed wrong calculation address position when check
condition.
In addition, it needs to check one more condition about overlapping
entire area.
Fixes: commit ce142f79e9e2 ("common: bootm: add checks to verify if ramdisk / fdtimage overlaps OS image") Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Bin Meng [Wed, 14 Oct 2020 06:34:52 +0000 (14:34 +0800)]
cmd: Add a 'misc' command to access miscellaneous devices
Enable the command "misc" for accessing miscellaneous devices with
a MISC uclass driver. The command provides listing all MISC devices
as well as read and write functionalities via their drivers.
Pali Rohár [Wed, 7 Oct 2020 13:39:40 +0000 (15:39 +0200)]
Makefile: Fix u-boot-nodtb.bin target
This change fixes two issues when building u-boot-nodtb.bin target:
* Remove intermediate binary u-boot-nodtb.bin from disk when static_rela
call (which modifies u-boot-nodtb.bin binary) failed. It is required
because previous objcopy call creates binary and static_rela finish it.
* Do not call static_rela cmd when u-boot-nodtb.bin binary was not
created/updated by previous objcopy call.
Second fix would ensure that u-boot-nodtb.bin binary is not updated when
all prerequisites were up-to-date. And therefore final binary u-boot.bin
is not updated in case all prerequisites were not modified and were
up-to-date.
Now running 'make SOURCE_DATE_EPOCH=0 u-boot.bin' second time now does not
touch u-boot.bin binary in case nothing was modified, so GNU make can
correctly detect that everything is up-to-date.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 22 Oct 2020 18:36:47 +0000 (14:36 -0400)]
Merge branch '2020-10-22-misc-changes'
- Assorted updates for Xen, IPQ40xx, ASpeed, Keymile
- Assorted typo / documentation fixes
- Fix default preboot cmd to act like before with USB_STORAGE set
- A number of other bugfixes throughout the code
AKASHI Takahiro [Thu, 15 Oct 2020 04:25:14 +0000 (13:25 +0900)]
arch: arm/xen: add putc() for debugging
This new function, xen_debug_putc(), is intended to be used to
enable CONFIG_DEBUG_UART on xen guest.
Please note that the underlying functionality in Xen is available
only when Xen is configured with !NDEBUG but is much simpler than
a generic HYPERVISOR_console_io().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Chia-Wei, Wang [Thu, 15 Oct 2020 02:25:13 +0000 (10:25 +0800)]
reset: ast2500: Use SCU for reset control
The System Control Unit (SCU) controller of Aspeed
SoCs provides the reset control for each peripheral.
This patch refactors the reset method to leverage
the SCU reset control. Thus the driver dependency
on watchdog including dedicated WDT API and reset
flag encoding can be eliminated.
The Kconfig description is also updated accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com> Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Dario Binacchi [Wed, 14 Oct 2020 21:42:17 +0000 (23:42 +0200)]
clk: ccf: replace the get_rate helper
The 24064745af commit fixed the get_rate helper because the set_parent
one did not re-parent the clock device to the new parent. The 957309678a
commit allows you to remove this workaround by calling the
clk_get_parent_rate routine.
Patrick Delaunay [Mon, 12 Oct 2020 07:47:50 +0000 (09:47 +0200)]
Remove default value of CONFIG_PREBOOT for CONFIG_USB_STORAGE
Remove the default value "usb start" for CONFIG_USB_STORAGE as the USB
storage boot initialization is correctly managed by distro boot command
('usb_boot' defined in include/config_distro_bootcmd.h already include
the command 'usb start').
Fixes: 36611e1991f3 ("Define default CONFIG_PREBOOT with right config option") Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Holger Brunck [Fri, 9 Oct 2020 15:21:33 +0000 (17:21 +0200)]
km/common: change ubicopy variable
Instead having a hard coded value for "cramfsaddr" after compile time,
we change it to take the variable "cramfsaddr" for the ubicopy variable.
This makes sure that ubicopy uses the right address, even when
the value for "cramfsaddr" has changed.
Holger Brunck [Fri, 9 Oct 2020 15:21:32 +0000 (17:21 +0200)]
km: adapt defines and variables for new memory layout
Due to increasing kernel image sizes we get problems when decompressing
the kernel image. To fix this we need to change the addresses where we
load and where we extract the kernel. Also we need to adapt the address
where to load the CRAMFS image and where to load the DTB file.
While at it also harmonize all boards for PPC and ARM to have the
same values. Also we add a new variable "env_version", so that the
userspace is able to detect if this is a u-boot binary with updated
values or not.
CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com> CC: Heiko Schocher <hs@denx.de> CC: Tom Rini <trini@konsulko.com> Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com> Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Remove old values from kmp204x.h] Signed-off-by: Tom Rini <trini@konsulko.com>
When building on a 32bit host the following warning occurs:
tools/image-host.c: In function ‘fit_image_read_data’:
tools/image-host.c:296:56: warning: format ‘%ld’ expects argument of
type ‘long int’, but argument 3 has type ‘__off64_t’
{aka ‘long long int’} [-Wformat=]
printf("File %s don't have the expected size (size=%ld, expected=%d)\n",
~~^
%lld
filename, sbuf.st_size, expected_size);
~~~~~~~~~~~~
tools/image-host.c:311:62: warning: format ‘%ld’ expects argument of
type ‘long int’, but argument 4 has type ‘__off64_t’
{aka ‘long long int’} [-Wformat=]
printf("Can't read all file %s (read %zd bytes, expexted %ld)\n",
~~^
%lld
filename, n, sbuf.st_size);
~~~~~~~~~~~~
Fix the format strings.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Holger Brunck [Thu, 8 Oct 2020 10:27:22 +0000 (12:27 +0200)]
km: fix license string and compatible strings
As the ownership is now Hitachi Power Grids, change the license string
and adapt the compatible string in DTS files. For kmeter1.dts we
change it to "keymile,KMETER1" for now, as this is then compliant with
what is submitted to the linux kernel. All other boards don't have
a upstreamed version in linux mainline.
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com> CC: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com> CC: Heiko Schocher <hs@denx.de> CC: Marek Vasut <marex@denx.de> CC: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Naoki Hayama [Thu, 8 Oct 2020 04:16:18 +0000 (13:16 +0900)]
README: Update links to mailing list archives
This patch includes these updates
- Change http://lists.denx.de/pipermail/u-boot
to https://lists.denx.de/pipermail/u-boot
- http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
is broken, so remove it
- Another archive https://marc.info/?l=u-boot
is available, so add it
Additional information:
dir.gmane.org has moved to news.gmane.io, but it only allows
access to the archive via NNTP.
- Server: news.gmane.io
- Group : gmane.comp.boot-loaders.u-boot
I don't include this information in this patch because
it's not very useful without web interfaces.
projects / uboot.git / log