Internal Receive and Transmit Clock Delays are a common setting for
RGMII capable devices.
While these delays are typically applied by the PHY, some MACs support
configuring internal clock delay settings, too. Hence add standardized
properties to configure this.
This is the MAC counterpart of commit db44e3751ab7d089 ("dt-bindings:
net: Add tx and rx internal delays"), which applies to the PHY.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Mon, 28 Sep 2020 09:05:56 +0000 (12:05 +0300)]
net/mlx5e: Fix a use after free on error in mlx5_tc_ct_shared_counter_get()
This code frees "shared_counter" and then dereferences on the next line
to get the error code.
Fixes: da404640cb59 ("net/mlx5e: CT: Use the same counter for both directions") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
net/mlx5: Fix dereference on pointer attr after null check
When removing a flow from the slow path fdb, a flow attr struct is
allocated for the rule removal process. If the allocation fails the
code prints a warning message but continues with the removal flow
which include dereferencing a pointer which could be null.
Fix this by exiting the function in case the attr allocation failed.
Use the PCI device directly for dma accesses as non PCI device unlikely
support IOMMU and dma mappings.
Introduce and use helper routine to access DMA device.
Parav Pandit [Mon, 31 Aug 2020 19:47:47 +0000 (22:47 +0300)]
net/mlx5: E-switch, Move devlink eswitch ports closer to eswitch
Currently devlink eswitch ports are registered and unregistered by the
representor layer.
However it is better to register them at eswitch layer so that in future
user initiated command port add and delete commands can also
register/unregister devlink ports without depending on representor layer.
Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Vu Pham <vuhuong@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently only 256 vports can be supported as only 8 bits are
reserved for them and 8 bits are reserved for vhca_ids in
metadata reg c0. To support more than 256 vports, replace
vhca_id with a unique shorter 4-bit PF number which covers
upto 16 PF's. Use remaining 12 bits for vports ranging 1-4095.
This will continue to generate unique metadata even if
multiple PCI devices have same switch_id.
Hamdan Igbaria [Mon, 15 Jun 2020 15:18:14 +0000 (18:18 +0300)]
net/mlx5: DR, Add support for rule creation with flow source hint
Skip the rule according to flow arrival source, in case of RX and the
source is local port skip and in case of TX and the source is uplink
skip, we get this info according to the flow source hint we get from
upper layers when creating the rule.
This is needed because for example in case of FDB table which has a TX
and RX tables and we are inserting a rule with an encap action which
is only a TX action, in this case rule will fail on RX, so we can rely
on the flow source hint and skip RX in such case.
Until now we relied on metadata regc_0 that upper layer mapped the
port in the regc_0, but the problem is that upper layer did not always
use regc_0 for port mapping, so now we added support to flow source
hint which upper layers will pass to SW steering when creating a rule.
net/mlx5: DR, Call ste_builder directly with tag pointer
Instead of getting the tag in each function, call the builder
directly with the tag. This will allow to use the same function
for building the tag and the bitmask.
net/mlx5: DR, Remove unneeded vlan check from L2 builder
When we create a matcher we check that all fields are consumed.
There is no need for this specific check. This keeps the STE
builder functions simple and clean.
net/mlx5: DR, Remove unneeded check from source port builder
Mask validity for ste builders is checked by mlx5dr_ste_build_pre_check
during matcher creation.
It already checks the mask value of source_vport, so removing
this duplicated check.
Also, moving there the check of source_eswitch_owner_vhca_id mask.
net/mlx5: DR, Replace the check for valid STE entry
Validity check is done by reading the next lu_type from the STE,
this check can be replaced by checking the refcount.
This will make the check independent on internal STE structure.
====================
drop_monitor: Convert to use devlink tracepoint
Drop monitor is able to monitor both software and hardware originated
drops. Software drops are monitored by having drop monitor register its
probe on the 'kfree_skb' tracepoint. Hardware originated drops are
monitored by having devlink call into drop monitor whenever it receives
a dropped packet from the underlying hardware.
This patch set converts drop monitor to monitor both software and
hardware originated drops in the same way - by registering its probe on
the relevant tracepoint.
In addition to drop monitor being more consistent, it is now also
possible to build drop monitor as module instead of as a builtin and
still monitor hardware originated drops. Initially, CONFIG_NET_DEVLINK
implied CONFIG_NET_DROP_MONITOR, but after commit 2f5a0f65c9f7
("kconfig: allow symbols implied by y to become m") we can have
CONFIG_NET_DEVLINK=y and CONFIG_NET_DROP_MONITOR=m and hardware
originated drops will not be monitored.
Patch set overview:
Patch #1 adds a tracepoint in devlink for trap reports.
Patch #2 prepares probe functions in drop monitor for the new
tracepoint.
Patch #3 converts drop monitor to use the new tracepoint.
Patches #4-#6 perform cleanups after the conversion.
Patch #7 adds a test case for drop monitor. Both software originated
drops and hardware originated drops (using netdevsim) are tested.
Tested:
| CONFIG_NET_DEVLINK | CONFIG_NET_DROP_MONITOR | Build | SW drops | HW drops |
| -------------------|-------------------------|-------|----------|----------|
| y | y | v | v | v |
| y | m | v | v | v |
| y | n | v | x | x |
| n | y | v | v | x |
| n | m | v | v | x |
| n | n | v | x | x |
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
drop_monitor: Filter control packets in drop monitor
Previously, devlink called into drop monitor in order to report hardware
originated drops / exceptions. devlink intentionally filtered control
packets and did not pass them to drop monitor as they were not dropped
by the underlying hardware.
Now drop monitor registers its probe on a generic 'devlink_trap_report'
tracepoint and should therefore perform this filtering itself instead of
having devlink do that.
Add the trap type as metadata and have drop monitor ignore control
packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The old probe functions that were invoked by drop monitor code are no
longer called and can thus be removed. They were replaced by actual
probe functions that are registered on the recently introduced
'devlink_trap_report' tracepoint.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Convert drop monitor to use the recently introduced
'devlink_trap_report' tracepoint instead of having devlink call into
drop monitor.
This is both consistent with software originated drops ('kfree_skb'
tracepoint) and also allows drop monitor to be built as a module and
still report hardware originated drops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drop_monitor: Prepare probe functions for devlink tracepoint
Drop monitor supports two alerting modes: Summary and packet. Prepare a
probe function for each, so that they could be later registered on the
devlink tracepoint by calling register_trace_devlink_trap_report(),
based on the configured alerting mode.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tracepoint for trap reports so that drop monitor could register
its probe on it. Use trace_devlink_trap_report_enabled() to avoid
wasting cycles setting the trap metadata if the tracepoint is not
enabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
this is a pull request of 13 patches for net-next.
The first 10 target the mcp25xxfd driver (which is renamed to mcp251xfd during
this series).
The first two patches are by Thomas Kopp, which adds reference to the just
related errata and updates the documentation and log messages.
Dan Carpenter's patch fixes a resource leak during ifdown.
A patch by me adds the missing initialization of a variable.
Oleksij Rempel updates the DT binding documentation as requested by Rob
Herring.
The next 5 patches are by Thomas Kopp and me. During review Geert Uytterhoeven
suggested to use "microchip,mcp251xfd" instead of "microchip,mcp25xxfd" as the
DT autodetection compatible to avoid clashes with future but incompatible
devices. We decided not only to rename the compatible but the whole driver from
"mcp25xxfd" to "mcp251xfd". This is done in several patches.
Joakim Zhang contributes three patches for the flexcan driver. The first one
adds support for the ECC feature, which is implemented on some modern IP cores,
by initializing the controller's memory during ifup. The next patch adds
support for the i.MX8MP (which supports ECC) and the last patch properly
disables the runtime PM if device registration fails.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 30 Sep 2020 22:11:09 +0000 (15:11 -0700)]
Merge branch 'ionic-watchdog-training'
Shannon Nelson says:
====================
ionic watchdog training
Our link watchdog displayed a couple of unfriendly behaviors in some recent
stress testing. These patches change the startup and stop timing in order
to be sure that expected structures are ready to be used by the watchdog.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Wed, 30 Sep 2020 17:48:28 +0000 (10:48 -0700)]
ionic: prevent early watchdog check
In one corner case scenario, the driver device lif setup can
get delayed such that the ionic_watchdog_cb() timer goes off
before the ionic->lif is set, thus causing a NULL pointer panic.
We catch the problem by checking for a NULL lif just a little
earlier in the callback.
Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
Shannon Nelson [Wed, 30 Sep 2020 17:48:27 +0000 (10:48 -0700)]
ionic: stop watchdog timer earlier on remove
We need to be better at making sure we don't have a link check
watchdog go off while we're shutting things down, so let's stop
the timer as soon as we start the remove.
Meanwhile, since that was the only thing in
ionic_dev_teardown(), simplify and remove that function.
Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
tcp: exponential backoff in tcp_send_ack()
We had outages caused by repeated skb allocation failures in tcp_send_ack()
It is time to add exponential backoff to reduce number of attempts.
Before doing so, first patch removes icsk_ack.blocked to make
room for a new field (icsk_ack.retry)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Sep 2020 12:54:57 +0000 (05:54 -0700)]
tcp: add exponential backoff in __tcp_send_ack()
Whenever host is under very high memory pressure,
__tcp_send_ack() skb allocation fails, and we setup
a 200 ms (TCP_DELACK_MAX) timer before retrying.
On hosts with high number of TCP sockets, we can spend
considerable amount of cpu cycles in these attempts,
add high pressure on various spinlocks in mm-layer,
ultimately blocking threads attempting to free space
from making any progress.
This patch adds standard exponential backoff to avoid
adding fuel to the fire.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Sep 2020 12:54:56 +0000 (05:54 -0700)]
inet: remove icsk_ack.blocked
TCP has been using it to work around the possibility of tcp_delack_timer()
finding the socket owned by user.
After commit f02b41be228f ("tcp: improve latencies of timer triggered events")
we added TCP_DELACK_TIMER_DEFERRED atomic bit for more immediate recovery,
so we can get rid of icsk_ack.blocked
This frees space that following patch will reuse.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
struct macb_platform_data is only used by macb_pci to register the platform
device, move its definition to cadence/macb.h and remove platform_data/macb.h
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 30 Sep 2020 21:06:54 +0000 (14:06 -0700)]
Merge branch 'mlxsw-PFC-and-headroom-selftests'
Petr Machata says:
====================
mlxsw: PFC and headroom selftests
Recent changes in the headroom management code made it clear that an
automated way of testing this functionality is needed. This patchset brings
two tests: a synthetic headroom behavior test, which verifies mechanics of
headroom management. And a PFC test, which verifies whether this behavior
actually translates into a working lossless configuration.
Both of these tests rely on mlnx_qos[1], a tool that interfaces with Linux
DCB API. The tool was originally written to work with Mellanox NICs, but
does not actually rely on anything Mellanox-specific, and can be used for
mlxsw as well as for any other NIC-like driver. Unlike Open LLDP it does
support buffer commands and permits a fire-and-forget approach to
configuration, which makes it very handy for writing of selftests.
Patches #1-#3 extend the selftest devlink_lib.sh in various ways. Patch #4
then adds a helper wrapper for mlnx_qos to mlxsw's qos_lib.sh.
Patch #5 adds a test for management of port headroom.
Petr Machata [Wed, 30 Sep 2020 10:49:11 +0000 (12:49 +0200)]
selftests: mlxsw: Add headroom handling test
Add a test for headroom configuration. This covers projection of ETS
configuration to ingress, PFC, adjustments for MTU, the qdisc / TC
mode and the effect of egress SPAN session on buffer configuration.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 30 Sep 2020 10:49:10 +0000 (12:49 +0200)]
selftests: mlxsw: qos_lib: Add a wrapper for running mlnx_qos
mlnx_qos is a script for configuration of DCB. Despite the name it is not
actually Mellanox-specific in any way. It is currently the only ad-hoc tool
available (in contrast to a daemon that manages an interface on an ongoing
basis). However, it is very verbose and parsing out error messages is not
really possible. Add a wrapper that makes it easier to use the tool.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 30 Sep 2020 10:49:09 +0000 (12:49 +0200)]
selftests: forwarding: devlink_lib: Support port-less topologies
Some selftests may not need any actual ports. Technically those are not
forwarding selftests, but devlink_lib can still be handy. Fall back on
NETIF_NO_CABLE in those cases.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 30 Sep 2020 10:49:07 +0000 (12:49 +0200)]
selftests: forwarding: devlink_lib: Split devlink_..._set() into save & set
Changing pool type from static to dynamic causes reinterpretation of
threshold values. They therefore need to be saved before pool type is
changed, then the pool type can be changed, and then the new values need
to be set up.
For that reason, set cannot subsume save, because it would be saving the
wrong thing, with possibly a nonsensical value, and restore would then fail
to restore the nonsensical value.
Thus extract a _save() from each of the relevant _set()'s. This way it is
possible to save everything up front, then to tweak it, and then restore in
the required order.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
can: flexcan: initialize all flexcan memory for ECC function
One issue was reported at a baremetal environment, which is used for
FPGA verification. "The first transfer will fail for extended ID
format(for both 2.0B and FD format), following frames can be transmitted
and received successfully for extended format, and standard format don't
have this issue. This issue occurred randomly with high possiblity, when
it occurs, the transmitter will detect a BIT1 error, the receiver a CRC
error. According to the spec, a non-correctable error may cause this
transfer failure."
With FLEXCAN_QUIRK_DISABLE_MECR quirk, it supports correctable errors,
disable non-correctable errors interrupt and freeze mode. Platform has
ECC hardware support, but select this quirk, this issue may not come to
light. Initialize all FlexCAN memory before accessing them, at least it
can avoid non-correctable errors detected due to memory uninitialized.
The internal region can't be initialized when the hardware doesn't support
ECC.
According to IMX8MPRM, Rev.C, 04/2020. There is a NOTE at the section
11.8.3.13 Detection and correction of memory errors:
"All FlexCAN memory must be initialized before starting its operation in
order to have the parity bits in memory properly updated. CTRL2[WRMFRZ]
grants write access to all memory positions that require initialization,
ranging from 0x080 to 0xADF and from 0xF28 to 0xFFF when the CAN FD feature
is enabled. The RXMGMASK, RX14MASK, RX15MASK, and RXFGMASK registers need to
be initialized as well. MCR[RFEN] must not be set during memory initialization."
Memory range from 0x080 to 0xADF, there are reserved memory (unimplemented
by hardware, e.g. only configure 64 MBs), these memory can be initialized or not.
In this patch, initialize all flexcan memory which includes reserved memory.
In this patch, create FLEXCAN_QUIRK_SUPPORT_ECC for platforms which has ECC
feature. If you have a ECC platform in your hand, please select this
qurik to initialize all flexcan memory firstly, then you can select
FLEXCAN_QUIRK_DISABLE_MECR to only enable correctable errors.
can: mcp251xfd: rename all remaining occurrence to mcp251xfd
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver,
which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming,
but incompatible chips.
In the previous patch the autodetect DT compatbile has been renamed to
"microchip,mcp251xfd", this patch changes all non user facing occurrence of
"mcp25xxfd" to "mcp251xfd" and "MCP25XXFD" to "MCP251XFD".
can: mcp251xfd: rename all user facing strings to mcp251xfd
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver,
which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming,
but incompatible chips.
In the previous patch the autodetect DT compatbile has been renamed to
"microchip,mcp251xfd", this patch changes all user facing strings from
"mcp25xxfd" to "mcp251xfd" and "MCP25XXFD" to "MCP251XFD", including:
- kconfig symbols
- name of kernel module
- DT and SPI compatible
can: mcp251xfd: rename driver files and subdir to mcp251xfd
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver,
which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming,
but incompatible chips.
In the previous patch the autodetect DT compatbile has been renamed to
"microchip,mcp251xfd", this patch changes the name of the driver subdir and the
individual files accordinly.
Thomas Kopp [Wed, 30 Sep 2020 09:14:22 +0000 (11:14 +0200)]
can: mcp25xxfd: narrow down wildcards in device tree bindings to "microchip,mcp251xfd"
The wildcard should be narrowed down to prevent existing and future devices
that are not compatible from matching. It is very unlikely that incompatible
devices will be released that do not match the wildcard.
Thomas Kopp [Wed, 30 Sep 2020 09:14:23 +0000 (11:14 +0200)]
dt-binding: can: mcp251xfd: narrow down wildcards in device tree bindings to "microchip,mcp251xfd"
The wildcard should be narrowed down to prevent existing and future devices
that are not compatible from matching. It is very unlikely that incompatible
devices will be released that do not match the wildcard.
Apply following fixes:
- Use 'interrupts'. (interrupts-extended will automagically be supported
by the tools)
- *-supply is always a single item. So, drop maxItems=1
- add "additionalProperties: false" flag to detect unneeded properties.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/r/20200923125301.27200-1-o.rempel@pengutronix.de Reported-by: Rob Herring <robh@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Fixes: 2dffde966ad8 ("dt-binding: can: mcp25xxfd: document device tree bindings") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Thomas Kopp [Fri, 25 Sep 2020 06:56:06 +0000 (08:56 +0200)]
can: mcp25xxfd: mcp25xxfd_handle_eccif(): add ECC related errata and update log messages
This patch adds a reference to the recent released MCP2517FD and MCP2518FD
errata sheets and paste the explanation.
The single error correction does not always work, so always indicate that a
single error occurred. If the location of the ECC error is outside of the
TX-RAM always use netdev_notice() to log the problem. For ECC errors in the
TX-RAM, there is a recovery procedure.
====================
HW support for VCAP IS1 and ES0 in mscc_ocelot
The patches from RFC series "Offload tc-flower to mscc_ocelot switch
using VCAP chains" have been split into 2:
https://patchwork.ozlabs.org/project/netdev/list/?series=204810&state=*
This is the boring part, that deals with the prerequisites, and not with
tc-flower integration. Apart from the initialization of some hardware
blocks, which at this point still don't do anything, no new
functionality is introduced.
- Key and action field offsets are defined for the supported switches.
- VCAP properties are added to the driver for the new TCAM blocks. But
instead of adding them manually as was done for IS2, which is error
prone, the driver is refactored to read these parameters from
hardware, which is possible.
- Some improvements regarding the processing of struct ocelot_vcap_filter.
- Extending the code to be compatible with full and quarter keys.
This series was tested, along with other patches not yet submitted, on
the Felix and Seville switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 29 Sep 2020 22:27:33 +0000 (01:27 +0300)]
net: mscc: ocelot: look up the filters in flower_stats() and flower_destroy()
Currently a new filter is created, containing just enough correct
information to be able to call ocelot_vcap_block_find_filter_by_index()
on it.
This will be limiting us in the future, when we'll have more metadata
associated with a filter, which will matter in the stats() and destroy()
callbacks, and which we can't make up on the spot. For example, we'll
start "offloading" some dummy tc filter entries for the TCAM skeleton,
but we won't actually be adding them to the hardware, or to block->rules.
So, it makes sense to avoid deleting those rules too. That's the kind of
thing which is difficult to determine unless we look up the real filter.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 29 Sep 2020 22:27:32 +0000 (01:27 +0300)]
net: mscc: ocelot: add a new ocelot_vcap_block_find_filter_by_id function
And rename the existing find to ocelot_vcap_block_find_filter_by_index.
The index is the position in the TCAM, and the id is the flow cookie
given by tc.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 29 Sep 2020 22:27:31 +0000 (01:27 +0300)]
net: mscc: ocelot: rename variable 'cnt' in vcap_data_offset_get()
The 'cnt' variable is actually used for 2 purposes, to hold the number
of sub-words per VCAP entry, and the number of sub-words per VCAP
action.
In fact, I'm pretty sure these 2 numbers can never be different from one
another. By hardware definition, the entry (key) TCAM rows are divided
into the same number of sub-words as its associated action RAM rows.
But nonetheless, let's at least rename the variables such that
observations like this one are easier to make in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xiaoliang Yang [Tue, 29 Sep 2020 22:27:29 +0000 (01:27 +0300)]
net: mscc: ocelot: calculate vcap offsets correctly for full and quarter entries
When calculating the offsets for the current entry within the row and
placing them inside struct vcap_data, the function assumes half key
entry (2 keys per row).
This patch modifies the vcap_data_offset_get() function to calculate a
correct data offset when the setting VCAP Type-Group of a key to
VCAP_TG_FULL or VCAP_TG_QUARTER.
This is needed because, for example, VCAP ES0 only supports full keys.
Also rename the 'count' variable to 'num_entries_per_row' to make the
function just one tiny bit easier to follow.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 29 Sep 2020 22:27:28 +0000 (01:27 +0300)]
net: mscc: ocelot: parse flower action before key
When we'll make the switch to multiple chain offloading, we'll want to
know first what VCAP block the rule is offloaded to. This impacts what
keys are available. Since the VCAP block is determined by what actions
are used, parse the action first.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.
Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 29 Sep 2020 22:27:23 +0000 (01:27 +0300)]
net: mscc: ocelot: generalize existing code for VCAP
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.
In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.
In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.
Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Second issue, the callers don't actually check the return value at all.
So in case the filter is not found in the rule list, propagate the
return code.
So update the callers and also take the opportunity to get rid of the
odd coding idioms that appear to work but don't.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 29 Sep 2020 22:27:21 +0000 (01:27 +0300)]
net: mscc: ocelot: introduce a new ocelot_target_{read,write} API
There are some targets (register blocks) in the Ocelot switch that are
instantiated more than once. For example, the VCAP IS1, IS2 and ES0
blocks all share the same register layout for interacting with the cache
for the TCAM and the action RAM.
For the VCAPs, the procedure for servicing them is actually common. We
just need an API specifying which VCAP we are talking to, and we do that
via these raw ocelot_target_read and ocelot_target_write accessors.
In plain ocelot_read, the target is encoded into the register enum
itself:
u16 target = reg >> TARGET_OFFSET;
For the VCAPs, the registers are currently defined like this:
which is precisely what we want to avoid, because we'd have to duplicate
the same register map for S1 and for S0, and then figure out how to pass
VCAP instance-specific registers to the ocelot_read calls (basically
another lookup table that undoes the effect of shifting with
TARGET_OFFSET).
So for some targets, propose a more raw API, similar to what is
currently done with ocelot_port_readl and ocelot_port_writel. Those
targets can only be accessed with ocelot_target_{read,write} and not
with ocelot_{read,write} after the conversion, which is fine.
The VCAP registers are not actually modified to use this new API as of
this patch. They will be modified in the next one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Tue, 29 Sep 2020 21:58:57 +0000 (23:58 +0200)]
net: mvneta: avoid possible cache misses in mvneta_rx_swbm
Do not use rx_desc pointers if possible since rx descriptors are stored in
uncached memory and dereferencing rx_desc pointers generate extra loads.
This patch improves XDP_DROP performance of ~ 110Kpps (700Kpps vs 590Kpps)
on Marvell Espressobin
Analyzed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus clearly requested that code in drivers and libraries which changes
behaviour based on execution context should either be split up so that
e.g. task context invocations and BH invocations have different interfaces
or if that's not possible the context information has to be provided by the
caller which knows in which context it is executing.
This includes conditional locking, allocation mode (GFP_*) decisions and
avoidance of code paths which might sleep.
In the long run, usage of 'preemptible, in_*irq etc.' should be banned from
driver code completely.
This is the second version of the first batch of related changes. V1 can be
found here:
net: rtlwifi: Replace in_interrupt() for context detection
rtl_lps_enter() and rtl_lps_leave() are using in_interrupt() to detect
whether it is safe to acquire a mutex or if it is required to defer to a
workqueue.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
in_interrupt() also is only partially correct because it fails to chose the
correct code path when just preemption or interrupts are disabled.
Add an argument 'may_block' to both functions and adjust the callers to
pass the context information.
The following call chains were analyzed to be safe to block:
rtl_watchdog_wq_callback()
rlf_lps_leave/enter()
rtl_op_suspend()
rtl_lps_leave()
rtl_op_bss_info_changed()
rtl_lps_leave()
rtl_op_sw_scan_start()
rtl_lps_leave()
The following call chains were analyzed to be unsafe to block:
This leaves four callers of rtl_lps_enter/leave() where the analyzis
stopped dead in the maze of several nested pointer based callchains and
lack of rtlwifi hardware to debug this via tracing:
These four have been cautionally marked to be unable to block which is the
safe option, but the rtwifi wizards should be able to clarify that.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: rtlwifi: Remove in_interrupt() from debug macro
The usage of in_interrupt() in drivers in is phased out.
rtl_dbg() a printk based debug aid is using in_interrupt() in the
underlying C function _rtl_dbg_out() which is almost identical to
_rtl_dbg_print(). The only difference is the printout of in_interrupt().
The decoding of in_interrupt() as hexvalue is non-trivial and aside of
being phased out for driver usage the return value is just by chance the
masked preempt count value and not a boolean.
These home brewn printk debug aids are tedious to work with and provide
only minimal context. They should be replaced by trace_printk() or a debug
tracepoint which automatically records all context information.
To make progress on the in_interrupt() cleanup, make rtl_dbg() use
_rtl_dbg_print() and remove _rtl_dbg_out().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: rtlwifi: Remove void* casts related to delayed work
INIT_DELAYED_WORK() takes two arguments: A pointer to the delayed work and
a function reference for the callback.
The rtl code casts all function references to (void *) because the
callbacks in use are not matching the required function signature. That's
error prone and bad pratice.
Some of the callback functions are also global, but only used in a single
file.
Clean the mess up by:
- Adding the proper arguments to the callback functions and using them in
the container_of() constructs correctly which removes the hideous
container_of_dwork_rtl() macro as well.
- Removing the type cast at the initializers
- Making the unnecessary global functions static
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
libertas uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: libertas libertas_tf: Remove in_interrupt() from debug macro.
The debug macro prints (INT) when in_interrupt() returns true. The value of
this information is dubious as it does not distinguish between the various
contexts which are covered by in_interrupt().
As the usage of in_interrupt() in drivers is phased out and the same
information can be more precisely obtained with tracing, remove the
in_interrupt() conditional from this debug printk.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
mwifiex uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
hfa384x_cmd() and prism2_hw_reset() check in_interrupt() at function entry
and if true emit a printk at debug loglevel and return. This is clearly debug
code.
Both functions invoke functions which can sleep. These functions already
have appropriate debug checks which cover all invalid contexts, while
in_interrupt() fails to detect context which just has preemption or
interrupts disabled.
Remove both checks as they are incomplete, debug only and already covered
by the subsequently invoked functions properly. If called from invalid
context the resulting back trace is definitely more helpful to analyze the
problem than a printk at debug loglevel.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: iwlwifi: Remove in_interrupt() from tracing macro.
The usage of in_interrupt) in driver code is phased out.
The iwlwifi_dbg tracepoint records in_interrupt() seperately, but that's
superfluous because the trace header already records all kind of state and
context information like hardirq status, softirq status, preemption count
etc.
Aside of that the recording of in_interrupt() as boolean does not allow to
distinguish between the possible contexts (hard interrupt, soft interrupt,
bottom half disabled) while the trace header gives precise information.
Remove the duplicate information from the tracepoint and fixup the caller.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Luca Coelho <luca@coelho.fi> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipw2x00,iwlegacy,iwlwifi: Remove in_interrupt() from debug macros
The usage of in_interrupt() in non-core code is phased out.
The debugging macros in these drivers use in_interrupt() to print 'I' or
'U' depending on the return value of in_interrupt(). While 'U' is confusing
at best and 'I' is not really describing the actual context (hard interupt,
soft interrupt, bottom half disabled section) these debug macros originate
from the pre ftrace kernel era and their value today is questionable. They
probably should be removed completely.
The macros weere added initially for ipw2100 and then spreaded when the
driver was forked.
Remove the in_interrupt() usage at least..
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
brcmf_fweh_process_event() uses in_interrupt() to select the allocation
mode GFP_KERNEL/GFP_ATOMIC. Aside of the above reasons this check is
incomplete as it cannot detect contexts which just have preemption or
interrupts disabled.
All callchains leading to brcmf_fweh_process_event() can clearly identify
the calling context. Convey a 'gfp' argument through the callchains and let
the callers hand in the appropriate GFP mode.
This has also the advantage that any change of execution context or
preemption/interrupt state in these callchains will be detected by the
memory allocator for all GFP_KERNEL allocations.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Arend van Spriel <arend.vanspriel@broadcom.com> Cc: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
brcmf_sdio_isr() is using in_interrupt() to distinguish if it is called
from a interrupt service routine or from a worker thread.
Passing such information from the calling context is preferred and
requested by Linus, so add an argument `in_isr' to brcmf_sdio_isr() and let
the callers pass the information about the calling context.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
lmc_trace() was first introduced in commit e7a392d5158af ("Import
2.3.99pre6-5") and was not touched ever since.
The reason for looking at this was to get rid of the in_interrupt() usage,
but while looking at it the following observations were made:
- At least lmc_get_stats() (->ndo_get_stats()) is invoked with disabled
preemption which is not detected by the in_interrupt() check, which
would cause schedule() to be called from invalid context.
- The code is hidden behind #ifdef LMC_TRACE which is not defined within
the kernel and wasn't at the time it was introduced.
- Three jiffies don't match 50ms. msleep() would be a better match which
would also avoid the schedule() invocation. But why have it to begin
with?
- Nobody would do something like this today. Either netdev_dbg() or
trace_printk() or a trace event would be used. If only the functions
related to this driver are interesting then ftrace can be used with
filtering.
As it is obviously broken for years, simply remove it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
The comment above nc_vendor_write() suggests that the function could become
async so that is usable in `in_interrupt()' context or that it already is
safe to be called from such a context.
Eitherway: The function did not become async since v2.4.9.2 (2002) and it
must be not be called from `in_interrupt()' context because it sleeps on
mutltiple occations.
Remove the misleading comment.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net: usb: kaweth: Remove last user of kaweth_control()
kaweth_async_set_rx_mode() invokes kaweth_contol() and has two callers:
- kaweth_open() which is invoked from preemptible context
.
- kaweth_start_xmit() which holds a spinlock and has bottom halfs disabled.
If called from kaweth_start_xmit() kaweth_async_set_rx_mode() obviously
cannot block, which means it can't call kaweth_control(). This is detected
with an in_interrupt() check.
Replace the in_interrupt() check in kaweth_async_set_rx_mode() with an
argument which is set true by the caller if the context is safe to sleep,
otherwise false.
Now kaweth_control() is only called from preemptible context which means
there is no need for GFP_ATOMIC allocations anymore. Replace it with
usb_control_msg(). Cleanup the code a bit while at it.
Finally remove kaweth_control() since the last user is gone.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: usb: kaweth: Replace kaweth_control() with usb_control_msg()
kaweth_control() is almost the same as usb_control_msg() except for the
memory allocation mode (GFP_ATOMIC vs GFP_NOIO) and the in_interrupt()
check.
All the invocations of kaweth_control() are within the probe function in
fully preemtible context so there is no reason to use atomic allocations,
GFP_NOIO which is used by usb_control_msg() is perfectly fine.
Replace kaweth_control() invocations from probe with usb_control_msg().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and
a tree wide effort to clean up and consolidate the (ab)usage of
in_interrupt() and related checks is happening.
handle_regs_int() is always invoked as part of URB callback which is either
invoked from hard or soft interrupt context.
Remove the magic assertion.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
vxge_os_dma_malloc() and vxge_os_dma_malloc_async() are both called from
callchains which use GFP_KERNEL allocations unconditionally or have other
requirements to be called from fully preemptible task context..
That means neither of these functions needs a conditional allocation mode.
Remove the in_interrupt() conditional and use GFP_KERNEL.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sun3lance: Remove redundant checks in interrupt handler
lance_interrupt() contains two pointless checks:
- A check whether the 'dev_id' argument is NULL. 'dev_id' is the pointer
which was handed in to request_irq() and the interrupt handler will
always be invoked with that pointer as 'dev_id' argument by the core
code.
- A check for interrupt reentrancy. The core code already guarantees
non-reentrancy of interrupt handlers.
Remove these check.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
bigmac_init_rings() has an argument signaling if it is called from the
interrupt handler. This is used to decide between GFP_KERNEL and GFP_ATOMIC
for memory allocations.
But it also checks in_interrupt() to handle invocations which come from the
timer callback bigmac_timer() via bigmac_hw_init(), which is invoked with
'in_irq = 0'. While the timer callback is clearly not in hard interrupt
context it is still not sleepable context.
Rename the argument to `non_blocking' and set it to true if invoked from
the timer callback or the interrupt handler which allows to remove the
in_interrupt() check and makes the code consistent.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sfc: Use GFP_KERNEL in efx_ef10_try_update_nic_stats()
efx_ef10_try_update_nic_stats_vf() is now only invoked from thread context
and can sleep after efx::stats_lock is dropped.
Change the allocation mode from GFP_ATOMIC to GFP_KERNEL. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Tue, 29 Sep 2020 20:25:24 +0000 (22:25 +0200)]
net: sfc: Replace in_interrupt() usage
efx_ef10_try_update_nic_stats_vf() used in_interrupt() to figure out
whether it is safe to sleep (for MCDI) or not.
The only caller from which it was not is efx_net_stats(), which can be
invoked under dev_base_lock from net-sysfs::netstat_show().
So add a new update_stats_atomic() method to struct efx_nic_type, and call
it from efx_net_stats(), removing the need for
efx_ef10_try_update_nic_stats_vf() to behave differently for this case
(which it wasn't doing correctly anyway).
For all nic_types other than EF10 VF, this method is NULL so the the
regular update_stats() methods are invoked , which are happy with being
called from atomic contexts.
Fixes: 5be74da53936 ("sfc: don't update stats on VF when called in atomic context") Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Gleixner [Tue, 29 Sep 2020 20:25:23 +0000 (22:25 +0200)]
net: natsemi: Replace in_interrupt() usage.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
sonic_quiesce() uses 'in_interrupt() || irqs_disabled()' to chose either
udelay() or usleep_range() in the wait loop.
In all callchains leading to it the context is well defined and known.
Add a 'may_sleep' argument and pass it through the various callchains
leading to this function.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the check covers only parts of the contexts in which these
functions cannot be called. It fails to detect preemption or interrupt
disabled invocations.
As the functions which contain these warnings invoke mutex_lock() which
contains a broad variety of checks (always enabled or debug option
dependent) and therefore covers all invalid conditions already, there is no
point in having inconsistent warnings in those drivers. The conditional
return is not really valuable in practice either.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the check covers only parts of the contexts in which these
functions cannot be called. It fails to detect preemption or interrupt
disabled invocations.
As the functions which are invoked from ionic_adminq_post() and
ionic_dev_cmd_wait() contain a broad variety of checks (always enabled or
debug option dependent) which cover all invalid conditions already, there
is no point in having inconsistent warnings in those drivers.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
The in_interrupt() usage in this driver tries to figure out which context
may sleep and which context may not sleep. in_interrupt() is not really
suitable as it misses both preemption disabled and interrupt disabled
invocations from task context.
Conditionals like that in driver code are frowned upon in general because
invocations of functions from invalid contexts might not be detected
as the conditional papers over it.
ionic_lif_addr() and _ionoc_lif_rx_mode() can be called from:
1) ->ndo_set_rx_mode() which is under netif_addr_lock_bh()) so it must not
sleep.
2) Init and setup functions which are in fully preemptible task context.
ionic_link_status_check_request() has two call paths:
1) NAPI which obviously cannot sleep
2) Setup which is again fully preemptible task context
Add arguments which convey the execution context to the affected functions
and let the callers provide the context instead of letting the functions
deduce it.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
in_interrupt() is ill defined and does not provide what the name
suggests. The usage especially in driver code is deprecated and a tree wide
effort to clean up and consolidate the (ab)usage of in_interrupt() and
related checks is happening.
In this case the checks cover only parts of the contexts in which these
functions cannot be called. They fail to detect preemption or interrupt
disabled invocations.
As the functions which are invoked from the various places contain already
a broad variety of checks (always enabled or debug option dependent) cover
all invalid conditions already, there is no point in having inconsistent
warnings in those drivers.
Just remove them.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
mpc52xx_fec_stop() uses in_interrupt() to check if it is safe to sleep. All
callers run in well defined contexts.
Pass an argument from the callers indicating whether it is safe to sleep.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net: e100: Remove in_interrupt() usage and pointless GFP_ATOMIC allocation
e100_hw_init() invokes e100_self_test() only if in_interrupt() returns
false as e100_self_test() uses msleep() which requires sleepable task
context. The in_interrupt() check is incomplete because in_interrupt()
cannot catch callers from contexts which have just preemption or interrupts
disabled.
e100_hw_init() is invoked from:
- e100_loopback_test() which clearly is sleepable task context as the
function uses msleep() itself.
- e100_up() which clearly is sleepable task context as well because it
invokes e100_alloc_cbs() abd request_irq() which both require sleepable
task context due to GFP_KERNEL allocations and mutex_lock() operations.
Remove the pointless in_interrupt() check.
As a side effect of this analysis it turned out that e100_rx_alloc_list()
which is only invoked from e100_loopback_test() and e100_up() pointlessly
uses a GFP_ATOMIC allocation. The next invoked function e100_alloc_cbs() is
using GFP_KERNEL already.
Change the allocation mode in e100_rx_alloc_list() to GFP_KERNEL as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log