Andrey Konovalov [Tue, 22 Dec 2020 20:01:52 +0000 (12:01 -0800)]
arm64: kasan: align allocations for HW_TAGS
Hardware tag-based KASAN uses the memory tagging approach, which requires
all allocations to be aligned to the memory granule size. Align the
allocations to MTE_GRANULE_SIZE via ARCH_SLAB_MINALIGN when
CONFIG_KASAN_HW_TAGS is enabled.
kasan, mm: untag page address in free_reserved_area
free_reserved_area() memsets the pages belonging to a given memory area.
As that memory hasn't been allocated via page_alloc, the KASAN tags that
those pages have are 0x00. As the result the memset might result in a tag
mismatch.
arm64: mte: switch GCR_EL1 in kernel entry and exit
When MTE is present, the GCR_EL1 register contains the tags mask that
allows to exclude tags from the random generation via the IRG instruction.
With the introduction of the new Tag-Based KASAN API that provides a
mechanism to reserve tags for special reasons, the MTE implementation has
to make sure that the GCR_EL1 setting for the kernel does not affect the
userspace processes and viceversa.
Save and restore the kernel/user mask in GCR_EL1 in kernel entry and exit.
The gcr_user mask is a per thread mask that represents the tags that are
excluded from random generation when the Memory Tagging Extension is
present and an 'irg' instruction is invoked.
gcr_user affects the behavior on EL0 only.
Currently that mask is an include mask and it is controlled by the user
via prctl() while GCR_EL1 accepts an exclude mask.
Convert the include mask into an exclude one to make it easier the
register setting.
Note: This change will affect gcr_kernel (for EL1) introduced with a
future patch.
Hardware tag-based KASAN relies on Memory Tagging Extension (MTE) feature
and requires it to be enabled. MTE supports
This patch adds a new mte_enable_kernel() helper, that enables MTE in
Synchronous mode in EL1 and is intended to be called from KASAN runtime
during initialization.
The Tag Checking operation causes a synchronous data abort as a
consequence of a tag check fault when MTE is configured in synchronous
mode.
As part of this change enable match-all tag for EL1 to allow the kernel to
access user pages without faulting. This is required because the kernel
does not have knowledge of the tags set by the user in a page.
Note: For MTE, the TCF bit field in SCTLR_EL1 affects only EL1 in a
similar way as TCF0 affects EL0.
MTE that is built on top of the Top Byte Ignore (TBI) feature hence we
enable it as part of this patch as well.
The hardware tag-based KASAN for compatibility with the other modes stores
the tag associated to a page in page->flags. Due to this the kernel
faults on access when it allocates a page with an initial tag and the user
changes the tags.
Reset the tag associated by the kernel to a page in all the meaningful
places to prevent kernel faults on access.
Note: An alternative to this approach could be to modify page_to_virt().
This though could end up being racy, in fact if a CPU checks the
PG_mte_tagged bit and decides that the page is not tagged but another CPU
maps the same with PROT_MTE and becomes tagged the subsequent kernel
access would fail.
Provide helper functions to manipulate allocation and pointer tags for
kernel addresses.
Low-level helper functions (mte_assign_*, written in assembly) operate tag
values from the [0x0, 0xF] range. High-level helper functions
(mte_get/set_*) use the [0xF0, 0xFF] range to preserve compatibility with
normal kernel pointers that have 0xFF in their top byte.
MTE_GRANULE_SIZE and related definitions are moved to mte-def.h header
that doesn't have any dependencies and is safe to include into any
low-level header.
Andrey Konovalov [Tue, 22 Dec 2020 20:01:20 +0000 (12:01 -0800)]
kasan: introduce CONFIG_KASAN_HW_TAGS
This patch adds a configuration option for a new KASAN mode called
hardware tag-based KASAN. This mode uses the memory tagging approach like
the software tag-based mode, but relies on arm64 Memory Tagging Extension
feature for tag management and access checking.
Andrey Konovalov [Tue, 22 Dec 2020 20:01:17 +0000 (12:01 -0800)]
kasan: separate metadata_fetch_row for each mode
This is a preparatory commit for the upcoming addition of a new hardware
tag-based (MTE-based) KASAN mode.
Rework print_memory_metadata() to make it agnostic with regard to the way
metadata is stored. Allow providing a separate metadata_fetch_row()
implementation for each KASAN mode. Hardware tag-based KASAN will provide
its own implementation that doesn't use shadow memory.
Andrey Konovalov [Tue, 22 Dec 2020 20:01:03 +0000 (12:01 -0800)]
kasan, arm64: rename kasan_init_tags and mark as __init
Rename kasan_init_tags() to kasan_init_sw_tags() as the upcoming hardware
tag-based KASAN mode will have its own initialization routine. Also
similarly to kasan_init() mark kasan_init_tags() as __init.
Andrey Konovalov [Tue, 22 Dec 2020 20:01:00 +0000 (12:01 -0800)]
kasan, arm64: move initialization message
Software tag-based KASAN mode is fully initialized with kasan_init_tags(),
while the generic mode only requires kasan_init(). Move the
initialization message for tag-based mode into kasan_init_tags().
Also fix pr_fmt() usage for KASAN code: generic.c doesn't need it as it
doesn't use any printing functions; tag-based mode should use "kasan:"
instead of KBUILD_MODNAME (which stands for file name).
Andrey Konovalov [Tue, 22 Dec 2020 20:00:46 +0000 (12:00 -0800)]
kasan: hide invalid free check implementation
This is a preparatory commit for the upcoming addition of a new hardware
tag-based (MTE-based) KASAN mode.
For software KASAN modes the check is based on the value in the shadow
memory. Hardware tag-based KASAN won't be using shadow, so hide the
implementation of the check in check_invalid_free().
Also simplify the code for software tag-based mode.
Andrey Konovalov [Tue, 22 Dec 2020 20:00:39 +0000 (12:00 -0800)]
kasan: rename report and tags files
Rename generic_report.c to report_generic.c and tags_report.c to
report_sw_tags.c, as their content is more relevant to report.c file.
Also rename tags.c to sw_tags.c to better reflect that this file contains
code for software tag-based mode.
Andrey Konovalov [Tue, 22 Dec 2020 20:00:35 +0000 (12:00 -0800)]
kasan: define KASAN_MEMORY_PER_SHADOW_PAGE
Define KASAN_MEMORY_PER_SHADOW_PAGE as (KASAN_GRANULE_SIZE << PAGE_SHIFT),
which is the same as (KASAN_GRANULE_SIZE * PAGE_SIZE) for software modes
that use shadow memory, and use it across KASAN code to simplify it.
Andrey Konovalov [Tue, 22 Dec 2020 20:00:32 +0000 (12:00 -0800)]
kasan: split out shadow.c from common.c
This is a preparatory commit for the upcoming addition of a new hardware
tag-based (MTE-based) KASAN mode.
The new mode won't be using shadow memory. Move all shadow-related code
to shadow.c, which is only enabled for software KASAN modes that use
shadow memory.
Andrey Konovalov [Tue, 22 Dec 2020 20:00:24 +0000 (12:00 -0800)]
kasan: rename KASAN_SHADOW_* to KASAN_GRANULE_*
This is a preparatory commit for the upcoming addition of a new hardware
tag-based (MTE-based) KASAN mode.
The new mode won't be using shadow memory, but will still use the concept
of memory granules. Each memory granule maps to a single metadata entry:
8 bytes per one shadow byte for generic mode, 16 bytes per one shadow byte
for software tag-based mode, and 16 bytes per one allocation tag for
hardware tag-based mode.
Rename KASAN_SHADOW_SCALE_SIZE to KASAN_GRANULE_SIZE, and
KASAN_SHADOW_MASK to KASAN_GRANULE_MASK.
Also use MASK when used as a mask, otherwise use SIZE.
Andrey Konovalov [Tue, 22 Dec 2020 20:00:21 +0000 (12:00 -0800)]
kasan: rename (un)poison_shadow to (un)poison_range
This is a preparatory commit for the upcoming addition of a new hardware
tag-based (MTE-based) KASAN mode.
The new mode won't be using shadow memory. Rename external annotation
kasan_unpoison_shadow() to kasan_unpoison_range(), and introduce internal
functions (un)poison_range() (without kasan_ prefix).
Andrey Konovalov [Tue, 22 Dec 2020 20:00:07 +0000 (12:00 -0800)]
kasan: drop unnecessary GPL text from comment headers
Patch series "kasan: add hardware tag-based mode for arm64", v11.
This patchset adds a new hardware tag-based mode to KASAN [1]. The new
mode is similar to the existing software tag-based KASAN, but relies on
arm64 Memory Tagging Extension (MTE) [2] to perform memory and pointer
tagging (instead of shadow memory and compiler instrumentation).
This patchset is co-developed and tested by
Vincenzo Frascino <vincenzo.frascino@arm.com>.
The underlying ideas of the approach used by hardware tag-based KASAN are:
1. By relying on the Top Byte Ignore (TBI) arm64 CPU feature, pointer tags
are stored in the top byte of each kernel pointer.
2. With the Memory Tagging Extension (MTE) arm64 CPU feature, memory tags
for kernel memory allocations are stored in a dedicated memory not
accessible via normal instuctions.
3. On each memory allocation, a random tag is generated, embedded it into
the returned pointer, and the corresponding memory is tagged with the
same tag value.
4. With MTE the CPU performs a check on each memory access to make sure
that the pointer tag matches the memory tag.
5. On a tag mismatch the CPU generates a tag fault, and a KASAN report is
printed.
Same as other KASAN modes, hardware tag-based KASAN is intended as a
debugging feature at this point.
====== Rationale
There are two main reasons for this new hardware tag-based mode:
1. Previously implemented software tag-based KASAN is being successfully
used on dogfood testing devices due to its low memory overhead (as
initially planned). The new hardware mode keeps the same low memory
overhead, and is expected to have significantly lower performance
impact, due to the tag checks being performed by the hardware.
Therefore the new mode can be used as a better alternative in dogfood
testing for hardware that supports MTE.
2. The new mode lays the groundwork for the planned in-kernel MTE-based
memory corruption mitigation to be used in production.
====== Technical details
Considering the implementation perspective, hardware tag-based KASAN is
almost identical to the software mode. The key difference is using MTE
for assigning and checking tags.
Compared to the software mode, the hardware mode uses 4 bits per tag, as
dictated by MTE. Pointer tags are stored in bits [56:60), the top 4 bits
have the normal value 0xF. Having less distict tags increases the
probablity of false negatives (from ~1/256 to ~1/16) in certain cases.
Only synchronous exceptions are set up and used by hardware tag-based KASAN.
====== Benchmarks
Note: all measurements have been performed with software emulation of Memory
Tagging Extension, performance numbers for hardware tag-based KASAN on the
actual hardware are expected to be better.
Boot time [1]:
* 2.8 sec for clean kernel
* 5.7 sec for hardware tag-based KASAN
* 11.8 sec for software tag-based KASAN
* 11.6 sec for generic KASAN
Slab memory usage after boot [2]:
* 7.0 kb for clean kernel
* 9.7 kb for hardware tag-based KASAN
* 9.7 kb for software tag-based KASAN
* 41.3 kb for generic KASAN
Measurements have been performed with:
* defconfig-based configs
* Manually built QEMU master
* QEMU arguments: -machine virt,mte=on -cpu max
* CONFIG_KASAN_STACK_ENABLE disabled
* CONFIG_KASAN_INLINE enabled
* clang-10 as the compiler and gcc-10 as the assembler
[1] Time before the ext4 driver is initialized.
[2] Measured as `cat /proc/meminfo | grep Slab`.
====== Notes
The cover letter for software tag-based KASAN patchset can be found here:
Linus Torvalds [Mon, 21 Dec 2020 18:39:37 +0000 (10:39 -0800)]
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
Linus Torvalds [Mon, 21 Dec 2020 18:35:11 +0000 (10:35 -0800)]
Merge tag 'm68knommu-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
- cleanup of 68328 code
- align BSS section to 32bit
* tag 'm68knommu-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: m68328: remove duplicate code
m68k: m68328: move platform code to separate files
m68knommu: align BSS section to 4-byte boundaries
Linus Torvalds [Mon, 21 Dec 2020 18:28:02 +0000 (10:28 -0800)]
Merge tag '9p-for-5.11-rc1' of git://github.com/martinetd/linux
Pull 9p update from Dominique Martinet:
- fix long-standing limitation on open-unlink-fop pattern
- add refcount to p9_fid (fixes the above and will allow for more
cleanups and simplifications in the future)
* tag '9p-for-5.11-rc1' of git://github.com/martinetd/linux:
9p: Remove unnecessary IS_ERR() check
9p: Uninitialized variable in v9fs_writeback_fid()
9p: Fix writeback fid incorrectly being attached to dentry
9p: apply review requests for fid refcounting
9p: add refcount to p9_fid struct
fs/9p: search open fids first
fs/9p: track open fids
fs/9p: fix create-unlink-getattr idiom
Stephen Boyd [Mon, 21 Dec 2020 01:18:05 +0000 (17:18 -0800)]
Merge branches 'clk-ingenic', 'clk-vc5', 'clk-cleanup', 'clk-canaan' and 'clk-marvell' into clk-next
- Bindings for Canaan K210 SoC clks
* clk-ingenic:
clk: ingenic: Fix divider calculation with div tables
* clk-vc5:
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
* clk-cleanup:
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: bcm: dvp: Add MODULE_DEVICE_TABLE()
clk: bcm: dvp: drop a variable that is assigned to only
Stephen Boyd [Mon, 21 Dec 2020 01:17:51 +0000 (17:17 -0800)]
Merge branches 'clk-ti', 'clk-analog', 'clk-trace', 'clk-at91' and 'clk-silabs' into clk-next
- Add some trace points for clk_set_rate() "range" functions
- DVFS support for AT91 clk driver
* clk-ti:
clk: ti: omap5: Fix reboot DPLL lock failure when using ABE TIMERs
clk: ti: Fix memleak in ti_fapll_synth_setup
* clk-analog:
clk: axi-clkgen: move the OF table at the bottom of the file
clk: axi-clkgen: wrap limits in a struct and keep copy on the state object
dt-bindings: clock: adi,axi-clkgen: convert old binding to yaml format
* clk-at91:
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
* clk-silabs:
clk: si5351: Wait for bit clear after PLL reset
Stephen Boyd [Mon, 21 Dec 2020 01:17:37 +0000 (17:17 -0800)]
Merge branches 'clk-tegra', 'clk-imx', 'clk-sifive', 'clk-mediatek' and 'clk-summary' into clk-next
- Support for SiFive FU740 PRCI
- Add hardware enable information to clk_summary debugfs
* clk-tegra:
clk: tegra: Fix duplicated SE clock entry
clk: tegra: bpmp: Clamp clock rates on requests
clk: tegra: Do not return 0 on failure
* clk-imx: (24 commits)
clk: imx: scu: remove the calling of device_is_bound
clk: imx: scu: Make pd_np with static keyword
clk: imx8mq: drop of_match_ptr from of_device_id table
clk: imx8mp: drop of_match_ptr from of_device_id table
clk: imx8mn: drop of_match_ptr from of_device_id table
clk: imx8mm: drop of_match_ptr from of_device_id table
clk: imx: gate2: Remove unused variable ret
clk: imx: gate2: Add locking in is_enabled op
clk: imx: gate2: Add cgr_mask for more flexible number of control bits
clk: imx: gate2: Check if clock is enabled against cgr_val
clk: imx: gate2: Keep the register writing in on place
clk: imx: gate2: Remove the IMX_CLK_GATE2_SINGLE_BIT special case
clk: imx: scu: fix build break when compiled as modules
clk: imx: remove redundant assignment to pointer np
clk: imx: remove unneeded semicolon
clk: imx: lpcg: add suspend/resume support
clk: imx: clk-imx8qxp-lpcg: add runtime pm support
clk: imx: lpcg: allow lpcg clk to take device pointer
clk: imx: imx8qxp-lpcg: add parsing clocks from device tree
clk: imx: scu: add suspend/resume support
...
* clk-sifive:
clk: sifive: Add clock enable and disable ops
clk: sifive: Fix the wrong bit field shift
clk: sifive: Add a driver for the SiFive FU740 PRCI IP block
clk: sifive: Use common name for prci configuration
clk: sifive: Extract prci core to common base
dt-bindings: fu740: prci: add YAML documentation for the FU740 PRCI
* clk-mediatek:
clk: mediatek: Make mtk_clk_register_mux() a static function
* clk-summary:
clk: Add hardware-enable column to clk summary
Stephen Boyd [Mon, 21 Dec 2020 01:17:01 +0000 (17:17 -0800)]
Merge branches 'clk-doc', 'clk-qcom', 'clk-simplify', 'clk-hw', 'clk-renesas' and 'clk-samsung' into clk-next
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
* clk-doc:
clk: fix a kernel-doc markup
* clk-qcom: (27 commits)
clk: qcom: rpmh: add support for SM8350 rpmh clocks
dt-bindings: clock: Add RPMHCC bindings for SM8350
clk: qcom: lpasscc: Introduce pm autosuspend for SC7180
clk: qcom: gcc-sc7180: Add 50 MHz clock rate for SDC2
clk: qcom: gcc-sc7180: Use floor ops for sdcc clks
clk: qcom: Add GDSC support for SDX55 GCC
dt-bindings: clock: Add GDSC in SDX55 GCC
clk: qcom: Add support for SDX55 RPMh clocks
dt-bindings: clock: Introduce RPMHCC bindings for SDX55
clk: qcom: Add SDX55 GCC support
dt-bindings: clock: Add SDX55 GCC clock bindings
clk: qcom: Kconfig: Fix spelling mistake "dyanmic" -> "dynamic"
clk: qcom: rpmh: Add CE clock on sdm845.
dt-bindings: clock: Add entry for crypto engine RPMH clock resource
clk: qcom: dispcc-sm8250: handle MMCX power domain
clk: qcom: camcc-sc7180: Use runtime PM ops instead of clk ones
clk: qcom: lpass-sc7180: Clean up on error in lpass_sc7180_init()
clk: qcom: Add support to LPASS AON_CC Glitch Free Mux clocks
clk: qcom: Add support to LPASS AUDIO_CC Glitch Free Mux clocks
dt-bindings: clock: Add support for LPASS Always ON Controller
...
* clk-hw:
clk: meson: g12: use devm variant to register notifiers
clk: add devm variant of clk_notifier_register
clk: meson: g12: drop use of __clk_lookup()
clk: add api to get clk consumer from clk_hw
clk: avoid devm_clk_release name clash
Linus Torvalds [Sun, 20 Dec 2020 21:08:19 +0000 (13:08 -0800)]
Merge tag '5.11-rc-smb3-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Four small CIFS/SMB3 fixes (witness protocol and reconnect related),
and two that add ability to get and set auditing information in the
security descriptor (SACL), which can be helpful not just for backup
scenarios ("smbinfo secdesc" etc.) but also for improving security"
* tag '5.11-rc-smb3-part2' of git://git.samba.org/sfrench/cifs-2.6:
Add SMB 2 support for getting and setting SACLs
SMB3: Add support for getting and setting SACLs
cifs: Avoid error pointer dereference
cifs: Re-indent cifs_swn_reconnect()
cifs: Unlock on errors in cifs_swn_reconnect()
cifs: Delete a stray unlock in cifs_swn_reconnect()
Linus Torvalds [Sun, 20 Dec 2020 19:21:06 +0000 (11:21 -0800)]
Merge tag 'perf-tools-2020-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools updates from Arnaldo Carvalho de Melo:
"perf record:
- Fix memory leak when using '--user-regs=?' to list registers
aarch64 support:
- Add aarch64 registers to 'perf record's' --user-regs command line
option
aarch64 hw tracing support:
- Decode memory tagging properties
- Improve ARM's auxtrace support
- Add support for ARMv8.3-SPE
perf kvm:
- Add kvm-stat for arm64
perf stat:
- Add --quiet option
Cleanups:
- Fixup function names wrt what is in libperf and what is in
tools/perf
Build:
- Allow building without libbpf in older systems
New kernel features:
- Initial support for data/code page size sample type, more to come
perf annotate:
- Support MIPS instruction extended support
perf stack unwinding:
- Fix separate debug info files when using elfutils' libdw's unwinder
perf vendor events:
- Update Intel's Skylake client events to v50
- Add JSON metrics for ARM's imx8mm DDR Perf
- Support printing metric groups for system PMUs
perf build id:
- Prep work for supporting having the build id provided by the kernel
in PERF_RECORD_MMAP2 metadata events
perf stat:
- Support regex pattern in --for-each-cgroup
pipe mode:
- Allow to use stdio functions for pipe mode
- Support 'perf report's' --header-only for pipe mode
- Support pipe mode display in 'perf evlist'
Documentation:
- Update information about CAP_PERFMON"
* tag 'perf-tools-2020-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (134 commits)
perf mem: Factor out a function to generate sort order
perf sort: Add sort option for data page size
perf script: Support data page size
tools headers UAPI: Update asm-generic/unistd.h
tools headers cpufeatures: Sync with the kernel sources
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools headers UAPI: Sync linux/fscrypt.h with the kernel sources
tools headers UAPI: Sync linux/const.h with the kernel headers
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf trace beauty: Update copy of linux/socket.h with the kernel sources
tools headers: Update linux/ctype.h with the kernel sources
tools headers: Add conditional __has_builtin()
tools headers: Get tools's linux/compiler.h closer to the kernel's
tools headers UAPI: Sync linux/stat.h with the kernel sources
tools headers: Syncronize linux/build_bug.h with the kernel sources
perf tools: Reformat record's control fd man text
perf config: Fix example command in manpage to conform to syntax specified in the SYNOPSIS section.
perf test: Make sample-parsing test aware of PERF_SAMPLE_{CODE,DATA}_PAGE_SIZE
perf tools: Add support to read build id from compressed elf
perf debug: Add debug_set_file function
...
Document the device tree bindings of the Canaan Kendryte K210 SoC clock
driver in Documentation/devicetree/bindings/clock/canaan,k210-clk.yaml.
The header file include/dt-bindings/clock/k210-clk.h is modified to
include the complete list of IDs for all clocks of the SoC.
Damien Le Moal [Sun, 20 Dec 2020 08:57:24 +0000 (17:57 +0900)]
dt-bindings: Add Canaan vendor prefix
Update Documentation/devicetree/bindings/vendor-prefixes.yaml to
include "canaan" as a vendor prefix for "Canaan Inc.". Canaan is the
vendor of the Kendryte K210 RISC-V SoC.
Linus Torvalds [Sun, 20 Dec 2020 18:44:05 +0000 (10:44 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Much x86 work was pushed out to 5.12, but ARM more than made up for it.
ARM:
- PSCI relay at EL2 when "protected KVM" is enabled
- New exception injection code
- Simplification of AArch32 system register handling
- Fix PMU accesses when no PMU is enabled
- Expose CSV3 on non-Meltdown hosts
- Cache hierarchy discovery fixes
- PV steal-time cleanups
- Allow function pointers at EL2
- Various host EL2 entry cleanups
- Simplification of the EL2 vector allocation
s390:
- memcg accouting for s390 specific parts of kvm and gmap
- selftest for diag318
- new kvm_stat for when async_pf falls back to sync
x86:
- Tracepoints for the new pagetable code from 5.10
- Catch VFIO and KVM irqfd events before userspace
- Reporting dirty pages to userspace with a ring buffer
- SEV-ES host support
- Nested VMX support for wait-for-SIPI activity state
- New feature flag (AVX512 FP16)
- New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
- Selftest improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: SVM: fix 32-bit compilation
KVM: SVM: Add AP_JUMP_TABLE support in prep for AP booting
KVM: SVM: Provide support to launch and run an SEV-ES guest
KVM: SVM: Provide an updated VMRUN invocation for SEV-ES guests
KVM: SVM: Provide support for SEV-ES vCPU loading
KVM: SVM: Provide support for SEV-ES vCPU creation/loading
KVM: SVM: Update ASID allocation to support SEV-ES guests
KVM: SVM: Set the encryption mask for the SVM host save area
KVM: SVM: Add NMI support for an SEV-ES guest
KVM: SVM: Guest FPU state save/restore not needed for SEV-ES guest
KVM: SVM: Do not report support for SMM for an SEV-ES guest
KVM: x86: Update __get_sregs() / __set_sregs() to support SEV-ES
KVM: SVM: Add support for CR8 write traps for an SEV-ES guest
KVM: SVM: Add support for CR4 write traps for an SEV-ES guest
KVM: SVM: Add support for CR0 write traps for an SEV-ES guest
KVM: SVM: Add support for EFER write traps for an SEV-ES guest
KVM: SVM: Support string IO operations for an SEV-ES guest
KVM: SVM: Support MMIO for an SEV-ES guest
KVM: SVM: Create trace events for VMGEXIT MSR protocol processing
KVM: SVM: Create trace events for VMGEXIT processing
...
Linus Torvalds [Sun, 20 Dec 2020 18:12:06 +0000 (10:12 -0800)]
Merge tag 'rtc-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- Remove nvram ABI. There was no complaints about the deprecation for
the last 3 years.
- Improve RTC device allocation and registration
- Now available for ARCH=um
Drivers:
- at91rm9200: correction and sam9x60 support
- ds1307: improve ACPI support
- mxc: now DT only
- pcf2127: watchdog support now needs the reset-source property
- pcf8523: set range
- rx6110: i2c support"
* tag 'rtc-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (43 commits)
rtc: pcf2127: only use watchdog when explicitly available
dt-bindings: rtc: add reset-source property
rtc: fix RTC removal
rtc: s3c: Remove dead code related to periodic tick handling
rtc: s3c: Disable all enable (RTC, tick) bits in the probe
rtc: ep93xx: Fix NULL pointer dereference in ep93xx_rtc_read_time
rtc: test: remove debug message
rtc: mxc{,_v2}: enable COMPILE_TEST
rtc: enable RTC framework on ARCH=um
rtc: pcf8523: use BIT
rtc: pcf8523: set range
rtc: pcf8523: switch to devm_rtc_allocate_device
rtc: destroy mutex when releasing the device
rtc: shrink devm_rtc_allocate_device()
rtc: rework rtc_register_device() resource management
rtc: nvmem: emit an error message when nvmem registration fails
rtc: add devm_ prefix to rtc_nvmem_register()
rtc: nvmem: remove nvram ABI
Documentation: list RTC devres helpers in devres.rst
rtc: omap: use devm_pinctrl_register()
...
Linus Torvalds [Sun, 20 Dec 2020 18:04:49 +0000 (10:04 -0800)]
Merge tag 'gfs2-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 updates from Andreas Gruenbacher:
- Don't wait for unfreeze of the wrong filesystems
- Remove an obsolete delete_work_func hack and an incorrect
sb_start_write
- Minor documentation updates and cosmetic care
* tag 'gfs2-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: in signal_our_withdraw wait for unfreeze of _this_ fs only
gfs2: Remove sb_start_write from gfs2_statfs_sync
gfs2: remove trailing semicolons from macro definitions
Revert "GFS2: Prevent delete work from occurring on glocks used for create"
gfs2: Make inode operations static
MAINTAINERS: Add gfs2 bug tracker link
Documentation: Update filesystems/gfs2.rst
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
Commit 45c940184b501fc6 ("dt-bindings: clk: versaclock5: convert to
yaml") accidentally changed "idt,voltage-microvolts" to
"idt,voltage-microvolt" in the DT bindings, while the driver still used
the former.
Update the driver to match the bindings, as
Documentation/devicetree/bindings/property-units.txt actually recommends
using "microvolt".
Fixes: 260249f929e81d3d ("clk: vc5: Enable addition output configurations of the Versaclock") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20201218125253.3815567-1-geert+renesas@glider.be Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Paul Cercueil [Sat, 12 Dec 2020 13:57:33 +0000 (13:57 +0000)]
clk: ingenic: Fix divider calculation with div tables
The previous code assumed that a higher hardware value always resulted
in a bigger divider, which is correct for the regular clocks, but is
an invalid assumption when a divider table is provided for the clock.
Perfect example of this is the PLL0_HALF clock, which applies a /2
divider with the hardware value 0, and a /1 divider otherwise.
Fixes: a9fa2893fcc6 ("clk: ingenic: Add support for divider tables") Cc: <stable@vger.kernel.org> # 5.2 Signed-off-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20201212135733.38050-1-paul@crapouillou.net Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Jernej Skrabec [Wed, 2 Dec 2020 20:38:17 +0000 (21:38 +0100)]
clk: sunxi-ng: Make sure divider tables have sentinel
Two clock divider tables are missing sentinel at the end. Effect of that
is that clock framework reads past the last entry. Fix that with adding
sentinel at the end.
Terry Zhou [Fri, 6 Nov 2020 10:00:39 +0000 (11:00 +0100)]
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
There is an error in the current code that the XTAL MODE
pin was set to NB MPP1_31 which should be NB MPP1_9.
The latch register of NB MPP1_9 has different offset of 0x8.
Signed-off-by: Terry Zhou <bjzhou@marvell.com>
[pali: Fix pin name in commit message] Signed-off-by: Pali Rohár <pali@kernel.org> Fixes: 7ea8250406a6 ("clk: mvebu: Add the xtal clock for Armada 3700 SoC") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201106100039.11385-1-pali@kernel.org Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Sascha Hauer [Mon, 30 Nov 2020 09:10:33 +0000 (10:10 +0100)]
clk: si5351: Wait for bit clear after PLL reset
Documentation states that SI5351_PLL_RESET_B and SI5351_PLL_RESET_A bits
are self clearing bits, so wait until they are cleared before
continuing.
This fixes a case when the clock doesn't come up properly after a PLL
reset. It worked properly when the frequency was below 900MHz, but with
900MHz it only works when we are waiting for the bit to clear.
Linus Torvalds [Sat, 19 Dec 2020 21:03:12 +0000 (13:03 -0800)]
Merge tag 'close-range-cloexec-unshare-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull close_range fix from Christian Brauner:
"syzbot reported a bug when asking close_range() to unshare the file
descriptor table and making all fds close-on-exec.
If CLOSE_RANGE_UNSHARE the caller will receive a private file
descriptor table in case their file descriptor table is currently
shared before operating on the requested file descriptor range.
For the case where the caller has requested all file descriptors to be
actually closed via e.g. close_range(3, ~0U, CLOSE_RANGE_UNSHARE) the
kernel knows that the caller does not need any of the file descriptors
anymore and will optimize the close operation by only copying all
files in the range from 0 to 3 and no others.
However, if the caller requested CLOSE_RANGE_CLOEXEC together with
CLOSE_RANGE_UNSHARE the caller wants to still make use of the file
descriptors so the kernel needs to copy all of them and can't
optimize.
The original patch didn't account for this and thus could cause oopses
as evidenced by the syzbot report because it assumed that all fds had
been copied. Fix this by handling the CLOSE_RANGE_CLOEXEC case and
copying all fds if the two flags are specified together.
This should've been caught in the selftests but the original patch
didn't cover this case and I didn't catch it during review. So in
addition to the bugfix I'm also adding selftests. They will reliably
reproduce the bug on a non-fixed kernel and allows us to catch
regressions and verify correct behavior.
Note, the kernel selftest tree contained a bunch of changes that made
the original selftest fail to compile so there are small fixups in
here make them compile without warnings"
* tag 'close-range-cloexec-unshare-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
selftests/core: add regression test for CLOSE_RANGE_UNSHARE | CLOSE_RANGE_CLOEXEC
selftests/core: add test for CLOSE_RANGE_UNSHARE | CLOSE_RANGE_CLOEXEC
selftests/core: handle missing syscall number for close_range
selftests/core: fix close_range_test build after XFAIL removal
close_range: unshare all fds for CLOSE_RANGE_UNSHARE | CLOSE_RANGE_CLOEXEC
Kan Liang [Wed, 16 Dec 2020 18:57:59 +0000 (10:57 -0800)]
perf mem: Factor out a function to generate sort order
Now, "--phys-data" is the only option which impacts the sort order. A
simple "if else" is enough to handle the option. But there will be more
options added, e.g. "--data-page-size", which also impact the sort
order. The code will become too complex to be maintained.
Divide the sort order string into several small pieces. The first piece
is always the default sort string for LOAD/STORE. Appends the specific
sort string if related option is applied.
No functional change.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Stephane Eranian <eranian@google.com> Cc: Will Deacon <will@kernel.org> Link: http://lore.kernel.org/lkml/20201216185805.9981-4-kan.liang@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Sat, 19 Dec 2020 20:50:10 +0000 (12:50 -0800)]
Merge branch 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux
Pull pcmcia updates from Dominik Brodowski:
"Besides a few PCMCIA odd fixes, the NEC VRC4173 CARDU driver is
removed, as it has not compiled in ages"
* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
pcmcia: omap: Fix error return code in omap_cf_probe()
pcmcia: Remove NEC VRC4173 CARDU
pcmcia: db1xxx_ss: remove unneeded semicolon
pcmcia/electra_cf: Fix some return values in 'electra_cf_probe()' in case of error
Linus Torvalds [Sat, 19 Dec 2020 19:58:46 +0000 (11:58 -0800)]
Merge tag 'for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Battery/charger driver changes:
- collie_battery, generic-adc-battery, s3c-adc-battery: convert to
GPIO descriptors (incl ARM board files)
- misc cleanup and fixes
Reset drivers:
- new poweroff driver for force disabling a regulator
- use printk format symbol resolver
- ocelot: add support for Luton and Jaguar2"
* tag 'for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (31 commits)
power: supply: Fix a typo in warning message
Documentation: DT: binding documentation for regulator-poweroff
power: reset: new driver regulator-poweroff
power: supply: ab8500: Use dev_err_probe() for IIO channels
power: supply: ab8500_fg: Request all IRQs as threaded
power: supply: ab8500_charger: Oneshot threaded IRQs
power: supply: ab8500: Convert to dev_pm_ops
power: supply: ab8500: Use local helper
power: supply: wm831x_power: remove unneeded break
power: supply: bq24735: Drop unused include
power: supply: bq24190_charger: Drop unused include
power: supply: generic-adc-battery: Use GPIO descriptors
power: supply: collie_battery: Convert to GPIO descriptors
power: supply: bq24190_charger: fix reference leak
power: supply: s3c-adc-battery: Convert to GPIO descriptors
power: reset: Use printk format symbol resolver
power: supply: axp20x_usb_power: Use power efficient workqueue for debounce
power: supply: axp20x_usb_power: fix typo
power: supply: max8997-charger: Improve getting charger status
power: supply: max8997-charger: Fix platform data retrieval
...
Linus Torvalds [Sat, 19 Dec 2020 19:53:47 +0000 (11:53 -0800)]
Merge tag 'hsi-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI updates from Sebastian Reichel:
"Misc cleanups"
* tag 'hsi-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
HSI: core: fix a kernel-doc markup
HSI: omap_ssi: Don't jump to free ID in ssi_add_controller()
Linus Torvalds [Sat, 19 Dec 2020 19:51:32 +0000 (11:51 -0800)]
Merge tag 'pwm/for-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This is a fairly big release cycle from the PWM framework's point of
view.
There's a large patcheset here which converts drivers to use the new
devm_platform_ioremap_resource() helper and a bunch of minor fixes to
existing drivers. Some of the existing drivers also add support for
more hardware, such as Atmel SAMA 5D2 and Mediatek MT8183.
Finally there's a couple of new drivers for Intel Keem Bay and LGM
SoCs as well as the DesignWare PWM controller"
* tag 'pwm/for-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (66 commits)
pwm: sun4i: Remove erroneous else branch
pwm: sl28cpld: Set driver data before registering the PWM chip
pwm: Remove unused function pwmchip_add_inversed()
pwm: imx27: Fix overflow for bigger periods
pwm: bcm2835: Support apply function for atomic configuration
pwm: keembay: Fix build failure with -Os
pwm: core: Use octal permission
pwm: lpss: Make compilable with COMPILE_TEST
pwm: Fix dependencies on HAS_IOMEM
pwm: Use -EINVAL for unsupported polarity
pwm: sti: Remove unnecessary blank line
pwm: sti: Avoid conditional gotos
pwm: Add PWM fan controller driver for LGM SoC
Add DT bindings YAML schema for PWM fan controller of LGM SoC
pwm: Add DesignWare PWM Controller Driver
dt-bindings: pwm: mtk-disp: add MT8167 SoC binding
pwm: mediatek: Add MT8183 SoC support
pwm: mediatek: Always use bus clock
dt-bindings: pwm: pwm-mediatek: Add documentation for MT8183 SoC
pwm: Add PWM driver for Intel Keem Bay
...
Claudiu Beznea [Thu, 19 Nov 2020 15:43:17 +0000 (17:43 +0200)]
clk: at91: sama7g5: register cpu clock
Register CPU clock as being the master clock prescaler. This would
be used by DVFS. The block schema of SAMA7G5's PMC contains also a divider
between master clock prescaler and CPU (PMC_CPU_RATIO.RATIO) but the
frequencies supported by SAMA7G5 could be directly received from
CPUPLL + master clock prescaler and the extra divider would do no work in
case it would be enabled.
Claudiu Beznea [Thu, 19 Nov 2020 15:43:16 +0000 (17:43 +0200)]
clk: at91: clk-master: re-factor master clock
Re-factor master clock driver by splitting it into 2 clocks: prescaller
and divider clocks. Based on registered clock flags the prescaler's rate
could be changed at runtime. This is necessary for platforms supporting
DVFS (e.g. SAMA7G5) where master clock could be changed at run-time.
Claudiu Beznea [Thu, 19 Nov 2020 15:43:15 +0000 (17:43 +0200)]
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
Since CPU PLL feeds both CPU clock and MCK0, MCK0 cannot go higher
than 200MHz and MCK0 maximum prescaller is 5 limit the CPU PLL at
1GHz to avoid MCK0 overclocking while CPU PLL is changed by DVFS.
Claudiu Beznea [Thu, 19 Nov 2020 15:43:14 +0000 (17:43 +0200)]
clk: at91: sama7g5: decrease lower limit for MCK0 rate
On SAMA7G5 CPU clock is changed at run-time by DVFS. Since MCK0 and
CPU clock shares the same parent clock (CPUPLL clock) the MCK0 is
also changed by DVFS to avoid over/under clocking of MCK0 consumers.
The lower limit is changed to be able to set MCK0 accordingly by
DVFS.
Claudiu Beznea [Thu, 19 Nov 2020 15:43:13 +0000 (17:43 +0200)]
clk: at91: sama7g5: remove mck0 from parent list of other clocks
MCK0 is changed at runtime by DVFS. Due to this, since not all IPs
are glitch free aware at MCK0 changes, remove MCK0 from parent list
of other clocks (e.g. generic clock, programmable/system clock, MCKX).
Claudiu Beznea [Thu, 19 Nov 2020 15:43:07 +0000 (17:43 +0200)]
clk: at91: sama7g5: fix compilation error
pmc_data_allocate() has been changed. pmc_data_free() was removed.
Adapt the code taking this into consideration. With this the programmable
clocks were also saved in sama7g5_pmc so that they could be later
referenced.
Fixes: cb783bbbcf54 ("clk: at91: sama7g5: add clock support for sama7g5") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com> Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com> Link: https://lore.kernel.org/r/1605800597-16720-2-git-send-email-claudiu.beznea@microchip.com Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Uwe Kleine-König [Fri, 20 Nov 2020 13:21:21 +0000 (14:21 +0100)]
clk: bcm: dvp: drop a variable that is assigned to only
The third parameter to devm_platform_get_and_ioremap_resource() is used
only to provide the used resource. As this variable isn't used
afterwards, switch to the function devm_platform_ioremap_resource()
which doesn't provide this output parameter.
Linus Torvalds [Sat, 19 Dec 2020 19:39:50 +0000 (11:39 -0800)]
Merge branch 'akpm' (patches from Andrew)
Merge still more updates from Andrew Morton:
"18 patches.
Subsystems affected by this patch series: mm (memcg and cleanups) and
epoll"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/Kconfig: fix spelling mistake "whats" -> "what's"
selftests/filesystems: expand epoll with epoll_pwait2
epoll: wire up syscall epoll_pwait2
epoll: add syscall epoll_pwait2
epoll: convert internal api to timespec64
epoll: eliminate unnecessary lock for zero timeout
epoll: replace gotos with a proper loop
epoll: pull all code between fetch_events and send_event into the loop
epoll: simplify and optimize busy loop logic
epoll: move eavail next to the list_empty_careful check
epoll: pull fatal signal checks into ep_send_events()
epoll: simplify signal handling
epoll: check for events when removing a timed out thread from the wait queue
mm/memcontrol:rewrite mem_cgroup_page_lruvec()
mm, kvm: account kvm_vcpu_mmap to kmemcg
mm/memcg: remove unused definitions
mm/memcg: warning on !memcg after readahead page charged
mm/memcg: bail early from swap accounting if memcg disabled
Willem de Bruijn [Fri, 18 Dec 2020 22:05:35 +0000 (14:05 -0800)]
epoll: convert internal api to timespec64
Patch series "add epoll_pwait2 syscall", v4.
Enable nanosecond timeouts for epoll.
Analogous to pselect and ppoll, introduce an epoll_wait syscall
variant that takes a struct timespec instead of int timeout.
This patch (of 4):
Make epoll more consistent with select/poll: pass along the timeout as
timespec64 pointer.
In anticipation of additional changes affecting all three polling
mechanisms:
- add epoll_pwait2 syscall with timespec semantics,
and share poll_select_set_timeout implementation.
- compute slack before conversion to absolute time,
to save one ktime_get_ts64 call.
epoll: eliminate unnecessary lock for zero timeout
We call ep_events_available() under lock when timeout is 0, and then call
it without locks in the loop for the other cases.
Instead, call ep_events_available() without lock for all cases. For
non-zero timeouts, we will recheck after adding the thread to the wait
queue. For zero timeout cases, by definition, user is opportunistically
polling and will have to call epoll_wait again in the future.
Note that this lock was kept in c5a282e9635e9 because the whole loop was
historically under lock.
This patch results in a 1% CPU/RPC reduction in RPC benchmarks.
Link: https://lkml.kernel.org/r/20201106231635.3528496-9-soheil.kdev@gmail.com Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Suggested-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Khazhismel Kumykov <khazhy@google.com> Cc: Guantao Liu <guantaol@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ep_events_available() is called multiple times around the busy loop logic,
even though the logic is generally not used. ep_reset_busy_poll_napi_id()
is similarly always called, even when busy loop is not used.
Eliminate ep_reset_busy_poll_napi_id() and inline it inside
ep_busy_loop(). Make ep_busy_loop() return whether there are any events
available after the busy loop. This will eliminate unnecessary loads and
branches, and simplifies the loop.
Link: https://lkml.kernel.org/r/20201106231635.3528496-6-soheil.kdev@gmail.com Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Khazhismel Kumykov <khazhy@google.com> Cc: Guantao Liu <guantaol@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
epoll: pull fatal signal checks into ep_send_events()
To simplify the code, pull in checking the fatal signals into
ep_send_events(). ep_send_events() is called only from ep_poll().
Note that, previously, we were always checking fatal events, but it is
checked only if eavail is true. This should be fine because the goal of
that check is to quickly return from epoll_wait() when there is a pending
fatal signal.
Link: https://lkml.kernel.org/r/20201106231635.3528496-4-soheil.kdev@gmail.com Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Suggested-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Khazhismel Kumykov <khazhy@google.com> Cc: Guantao Liu <guantaol@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
epoll: check for events when removing a timed out thread from the wait queue
Patch series "simplify ep_poll".
This patch series is a followup based on the suggestions and feedback by
Linus:
https://lkml.kernel.org/r/CAHk-=wizk=OxUyQPbO8MS41w2Pag1kniUV5WdD5qWL-gq1kjDA@mail.gmail.com
The first patch in the series is a fix for the epoll race in presence of
timeouts, so that it can be cleanly backported to all affected stable
kernels.
The rest of the patch series simplify the ep_poll() implementation. Some
of these simplifications result in minor performance enhancements as well.
We have kept these changes under self tests and internal benchmarks for a
few days, and there are minor (1-2%) performance enhancements as a result.
This patch (of 8):
After abc610e01c66 ("fs/epoll: avoid barrier after an epoll_wait(2)
timeout"), we break out of the ep_poll loop upon timeout, without checking
whether there is any new events available. Prior to that patch-series we
always called ep_events_available() after exiting the loop.
This can cause races and missed wakeups. For example, consider the
following scenario reported by Guantao Liu:
Suppose we have an eventfd added using EPOLLET to an epollfd.
Thread 1: Sleeps for just below 5ms and then writes to an eventfd.
Thread 2: Calls epoll_wait with a timeout of 5 ms. If it sees an
event of the eventfd, it will write back on that fd.
Thread 3: Calls epoll_wait with a negative timeout.
Prior to abc610e01c66, it is guaranteed that Thread 3 will wake up either
by Thread 1 or Thread 2. After abc610e01c66, Thread 3 can be blocked
indefinitely if Thread 2 sees a timeout right before the write to the
eventfd by Thread 1. Thread 2 will be woken up from
schedule_hrtimeout_range and, with evail 0, it will not call
ep_send_events().
To fix this issue:
1) Simplify the timed_out case as suggested by Linus.
2) while holding the lock, recheck whether the thread was woken up
after its time out has reached.
Note that (2) is different from Linus' original suggestion: It do not set
"eavail = ep_events_available(ep)" to avoid unnecessary contention (when
there are too many timed-out threads and a small number of events), as
well as races mentioned in the discussion thread.
This is the first patch in the series so that the backport to stable
releases is straightforward.
Hui Su [Fri, 18 Dec 2020 22:01:41 +0000 (14:01 -0800)]
mm/memcontrol:rewrite mem_cgroup_page_lruvec()
mem_cgroup_page_lruvec() in memcontrol.c and mem_cgroup_lruvec() in
memcontrol.h is very similar except for the param(page and memcg) which
also can be convert to each other.
So rewrite mem_cgroup_page_lruvec() with mem_cgroup_lruvec().
[alex.shi@linux.alibaba.com: add missed warning in mem_cgroup_lruvec] Link: https://lkml.kernel.org/r/94f17bb7-ec61-5b72-3555-fabeb5a4d73b@linux.alibaba.com
[lstoakes@gmail.com: warn on missing memcg on mem_cgroup_page_lruvec()] Link: https://lkml.kernel.org/r/20201125112202.387009-1-lstoakes@gmail.com Link: https://lkml.kernel.org/r/20201108143731.GA74138@rlk Signed-off-by: Hui Su <sh_def@163.com> Signed-off-by: Alex Shi <alex.shi@linux.alibaba.com> Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <guro@fb.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Yafang Shao <laoar.shao@gmail.com> Cc: Chris Down <chris@chrisdown.name> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shakeel Butt [Fri, 18 Dec 2020 22:01:38 +0000 (14:01 -0800)]
mm, kvm: account kvm_vcpu_mmap to kmemcg
A VCPU of a VM can allocate couple of pages which can be mmap'ed by the
user space application. At the moment this memory is not charged to the
memcg of the VMM. On a large machine running large number of VMs or
small number of VMs having large number of VCPUs, this unaccounted
memory can be very significant. So, charge this memory to the memcg of
the VMM. Please note that lifetime of these allocations corresponds to
the lifetime of the VMM.
Link: https://lkml.kernel.org/r/20201106202923.2087414-1-shakeelb@google.com Signed-off-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <guro@fb.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Shi [Fri, 18 Dec 2020 22:01:31 +0000 (14:01 -0800)]
mm/memcg: warning on !memcg after readahead page charged
Add VM_WARN_ON_ONCE_PAGE() macro.
Since readahead page is charged on memcg too, in theory we don't have to
check this exception now. Before safely remove them all, add a warning
for the unexpected !memcg.
Link: https://lkml.kernel.org/r/1604283436-18880-3-git-send-email-alex.shi@linux.alibaba.com Signed-off-by: Alex Shi <alex.shi@linux.alibaba.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Hugh Dickins <hughd@google.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alex Shi [Fri, 18 Dec 2020 22:01:28 +0000 (14:01 -0800)]
mm/memcg: bail early from swap accounting if memcg disabled
Patch series "bail out early for memcg disable".
These 2 patches are indepenedent from per memcg lru lock, and may
encounter unexpected warning, so let's move out them from per memcg
lru locking patchset.
This patch (of 2):
We could bail out early when memcg wasn't enabled.
selftests/core: add regression test for CLOSE_RANGE_UNSHARE | CLOSE_RANGE_CLOEXEC
This test is a minimalized version of the reproducer given by syzbot
(cf. [1]).
After introducing CLOSE_RANGE_CLOEXEC syzbot reported a crash when
CLOSE_RANGE_CLOEXEC is specified in conjunction with
CLOSE_RANGE_UNSHARE. When CLOSE_RANGE_UNSHARE is specified the caller
will receive a private file descriptor table in case their file
descriptor table is currently shared.
For the case where the caller has requested all file descriptors to be
actually closed via e.g. close_range(3, ~0U, 0) the kernel knows that
the caller does not need any of the file descriptors anymore and will
optimize the close operation by only copying all files in the range from
0 to 3 and no others.
However, if the caller requested CLOSE_RANGE_CLOEXEC together with
CLOSE_RANGE_UNSHARE the caller wants to still make use of the file
descriptors so the kernel needs to copy all of them and can't optimize.
The original patch didn't account for this and thus could cause oopses
as evidenced by the syzbot report. Add tests for this regression.
We first create a huge gap in the fd table. When we now call
CLOSE_RANGE_UNSHARE with a shared fd table and and with ~0U as upper
bound the kernel will only copy up to fd1 file descriptors into the new
fd table. If the kernel is buggy and doesn't handle CLOSE_RANGE_CLOEXEC
correctly it will not have copied all file descriptors and we will oops!
This test passes on a fixed kernel and will trigger an oops on a buggy
kernel.
projects / kernel.git / log