Zenghui Yu [Thu, 6 Feb 2020 07:57:06 +0000 (15:57 +0800)]
irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
The Size field of GICv4.1 VPROPBASER register indicates number of
pages minus one and together Page_Size and Size control the vPEID
width. Let's respect this requirement of the architecture.
Zenghui Yu [Mon, 2 Dec 2019 07:10:21 +0000 (15:10 +0800)]
irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
It looks like an obvious mistake to use its_mapc_cmd descriptor when
building the INVALL command block. It so far worked by luck because
both its_mapc_cmd.col and its_invall_cmd.col sit at the same offset of
the ITS command descriptor, but we should not rely on it.
Marc Zyngier [Mon, 16 Dec 2019 11:24:57 +0000 (11:24 +0000)]
irqchip/gic-v3: Only provision redistributors that are enabled in ACPI
We currently allocate redistributor region structures for
individual redistributors when ACPI doesn't present us with
compact MMIO regions covering multiple redistributors.
It turns out that we allocate these structures even when
the redistributor is flagged as disabled by ACPI. It works
fine until someone actually tries to tarse one of these
structures, and access the corresponding MMIO region.
Instead, track the number of enabled redistributors, and
only allocate what is required. This makes sure that there
is no invalid data to misuse.
Marc Zyngier [Tue, 24 Dec 2019 11:10:37 +0000 (11:10 +0000)]
irqchip/gic-v4.1: Suppress per-VLPI doorbell
Since GICv4.1 gives us a per-VPE doorbell, avoid programming anything
else on VMOVI/VMAPI/VMAPTI and on any other action that would have
otherwise resulted in a per-VLPI doorbell to be programmed.
Marc Zyngier [Tue, 24 Dec 2019 11:10:35 +0000 (11:10 +0000)]
irqchip/gic-v4.1: Add VPE eviction callback
When descheduling a VPE, special care must be taken to tell the GIC
about whether we want to receive a doorbell or not. This is a
major improvement on GICv4.0, where the doorbell had to be separately
enabled/disabled.
Marc Zyngier [Tue, 24 Dec 2019 11:10:34 +0000 (11:10 +0000)]
irqchip/gic-v4.1: Add VPE residency callback
Making a VPE resident on GICv4.1 is pretty simple, as it is just a
single write to the local redistributor. We just need extra information
about which groups to enable, which the KVM code will have to provide.
Marc Zyngier [Tue, 24 Dec 2019 11:10:32 +0000 (11:10 +0000)]
irqchip/gic-v4.1: Plumb skeletal VPE irqchip
Just like for GICv4.0, each VPE has its own doorbell interrupt, and
thus an irqchip that manages them. Since the doorbell management is
quite different on GICv4.1, let's introduce an almost empty irqchip
the will get populated over the next new patches.
Marc Zyngier [Tue, 24 Dec 2019 11:10:31 +0000 (11:10 +0000)]
irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP
With GICv4.1, VMOVP is extended to allow a default doorbell to be
specified, as well as a validity bit for this doorbell. As an added
bonus, VMOVP isn't required anymore of moving a VPE between
redistributors that share the same affinity.
Let's add this support to the VMOVP builder, and make sure we don't
issue the command if we don't really need to.
Marc Zyngier [Tue, 24 Dec 2019 11:10:30 +0000 (11:10 +0000)]
irqchip/gic-v4.1: Don't use the VPE proxy if RVPEID is set
The infamous VPE proxy device isn't used with GICv4.1 because:
- we can invalidate any LPI from the DirectLPI MMIO interface
- the ITS and redistributors understand the life cycle of
the doorbell, so we don't need to enable/disable it all
the time
So let's escape early from the proxy related functions.
Marc Zyngier [Tue, 24 Dec 2019 11:10:29 +0000 (11:10 +0000)]
irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP
The ITS VMAPP command gains some new fields with GICv4.1:
- a default doorbell, which allows a single doorbell to be used for
all the VLPIs routed to a given VPE
- a pointer to the configuration table (instead of having it in a register
that gets context switched)
- a flag indicating whether this is the first map or the last unmap for
this particular VPE
- a flag indicating whether the pending table is known to be zeroed, or not
Plumb in the new fields in the VMAPP builder, and add the map/unmap
refcounting so that the ITS can do the right thing.
GICv4.1 defines a new VPE table that is potentially shared between
both the ITSs and the redistributors, following complicated affinity
rules.
To make things more confusing, the programming of this table at
the redistributor level is reusing the GICv4.0 GICR_VPROPBASER register
for something completely different.
The code flow is somewhat complexified by the need to respect the
affinities required by the HW, meaning that tables can either be
inherited from a previously discovered ITS or redistributor.
Marc Zyngier [Tue, 24 Dec 2019 11:10:25 +0000 (11:10 +0000)]
irqchip/gic-v3: Add GICv4.1 VPEID size discovery
While GICv4.0 mandates 16 bit worth of VPEIDs, GICv4.1 allows smaller
implementations to be built. Add the required glue to dynamically
compute the limit.
Marc Zyngier [Tue, 24 Dec 2019 11:10:24 +0000 (11:10 +0000)]
irqchip/gic-v3: Detect GICv4.1 supporting RVPEID
GICv4.1 supports the RVPEID ("Residency per vPE ID"), which allows for
a much efficient way of making virtual CPUs resident (to allow direct
injection of interrupts).
The functionnality needs to be discovered on each and every redistributor
in the system, and disabled if the settings are inconsistent.
Marc Zyngier [Wed, 22 Jan 2020 13:53:44 +0000 (13:53 +0000)]
irqchip/gic-v3-its: Fix get_vlpi_map() breakage with doorbells
When updating an LPI configuration, get_vlpi_map() may be passed a
irq_data structure relative to an ITS domain (the normal case) or one
that is relative to the core GICv3 domain in the case of a GICv4
doorbell.
In the latter case, special care must be take not to dereference
the irq_chip data as an its_dev structure, as that isn't what is
stored there. Instead, check *first* whether the IRQ is forwarded
to a vcpu, and only then try to obtain the vlpi mapping.
Joakim Zhang [Fri, 17 Jan 2020 06:10:10 +0000 (06:10 +0000)]
irqchip: Add NXP INTMUX interrupt multiplexer support
The Interrupt Multiplexer (INTMUX) expands the number of peripherals
that can interrupt the core:
* The INTMUX has 8 channels that are assigned to 8 NVIC interrupt slots.
* Each INTMUX channel can receive up to 32 interrupt sources and has 1
interrupt output.
* The INTMUX routes the interrupt sources to the interrupt outputs.
Hyunki Koo [Tue, 24 Dec 2019 21:11:07 +0000 (06:11 +0900)]
irqchip: Define EXYNOS_IRQ_COMBINER
This patch is written to clean up dependency of ARCH_EXYNOS
Not all exynos device have IRQ_COMBINER, especially aarch64 EXYNOS
but it is built for all exynos devices.
Thus add the config for EXYNOS_IRQ_COMBINER
remove direct dependency between ARCH_EXYNOS and exynos-combiner.c
and only selected on the aarch32 devices
Qianggui Song [Mon, 16 Dec 2019 12:36:44 +0000 (20:36 +0800)]
irqchip/meson-gpio: Add support for meson a1 SoCs
The meson a1 Socs have some changes compared with previous
chips. For A113L, it contains 62 pins and can be spied on:
- 62:128 undefined
- 61:50 12 pins on bank A
- 49:37 13 pins on bank F
- 36:20 17 pins on bank X
- 19:13 7 pins on bank B
- 12:0 13 pins on bank P
There are five relative registers for gpio interrupt controller,
details are as below:
- PADCTRL_GPIO_IRQ_CTRL0
bit[31]: enable/disable the whole irq lines
bit[16-23]: both edge trigger
bit[8-15]: single edge trigger
bit[0-7]: pol trigger
- PADCTRL_GPIO_IRQ_CTRL[X]
bit[0-6]: 7 bits to choose gpio source for irq line 2*[X] - 2
bit[16-22]: 7 bits to choose gpio source for irq line 2*[X] - 1
where X =1,2,3,4
Qianggui Song [Mon, 16 Dec 2019 12:36:43 +0000 (20:36 +0800)]
irqchip/meson-gpio: Rework meson irqchip driver to support meson-A1 SoCs
Since Meson-A1 SoCs register layout of gpio interrupt controller has
difference with previous chips, registers to decide irq line and offset
of trigger method are all changed, the current driver should be modified.
The specific problem here is that the mbigen driver real probe has failed
as the mbigen_of_create_domain()->of_platform_device_create() call fails,
the reason for that being that we never destroyed the platform device
created during the remove test dry run and there is some conflict.
Since we generally would never want to unbind this driver, and to save
adding a driver tear down path for that, just set the driver
.suppress_bind_attrs member to avoid this possibility.
Eddie James [Wed, 15 Jan 2020 21:29:40 +0000 (15:29 -0600)]
irqchip: Add Aspeed SCU interrupt controller
The Aspeed SOCs provide some interrupts through the System Control
Unit registers. Add an interrupt controller that provides these
interrupts to the system.
Linus Torvalds [Sun, 29 Dec 2019 18:01:27 +0000 (10:01 -0800)]
Merge tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"One important fix for RISC-V:
- Redirect any incoming syscall with an ID less than -1 to
sys_ni_syscall, rather than allowing them to fall through into the
syscall handler.
and two minor build fixes:
- Export __asm_copy_{from,to}_user() from where they are defined.
This fixes a build error triggered by some randconfigs.
- Export flush_icache_all(). I'd resisted this before, since
historically we didn't want modules to be able to flush the I$
directly; but apparently everyone else is doing it now"
* tag 'riscv/for-v5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: export flush_icache_all to modules
riscv: reject invalid syscalls below -1
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
Linus Torvalds [Sun, 29 Dec 2019 17:50:57 +0000 (09:50 -0800)]
Merge tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull /proc/locks formatting fix from Jeff Layton:
"This is a trivial fix for a _very_ long standing bug in /proc/locks
formatting. Ordinarily, I'd wait for the merge window for something
like this, but it is making it difficult to validate some overlayfs
fixes.
I've also gone ahead and marked this for stable"
* tag 'locks-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: print unsigned ino in /proc/locks
Linus Torvalds [Sun, 29 Dec 2019 17:48:47 +0000 (09:48 -0800)]
Merge tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"One performance fix for large directory searches, and one minor style
cleanup noticed by Clang"
* tag '5.5-rc3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Optimize readdir on reparse points
cifs: Adjust indentation in smb2_open_file
Olof Johansson [Tue, 17 Dec 2019 04:07:04 +0000 (20:07 -0800)]
riscv: export flush_icache_all to modules
This is needed by LKDTM (crash dump test module), it calls
flush_icache_range(), which on RISC-V turns into flush_icache_all(). On
other architectures, the actual implementation is exported, so follow
that precedence and export it here too.
Fixes build of CONFIG_LKDTM that fails with:
ERROR: "flush_icache_all" [drivers/misc/lkdtm/lkdtm.ko] undefined!
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Running "stress-ng --enosys 4 -t 20 -v" showed a large number of kernel oops
with "Unable to handle kernel paging request at virtual address" message. This
happens when enosys stressor starts testing random non-valid syscalls.
I forgot to redirect any syscall below -1 to sys_ni_syscall.
With the patch kernel oops messages are gone while running stress-ng enosys
stressor.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com> Fixes: f13529dcecc9 ("riscv: add support for SECCOMP and SECCOMP_FILTER") Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
riscv: fix compile failure with EXPORT_SYMBOL() & !MMU
When support for !MMU was added, the declaration of
__asm_copy_to_user() & __asm_copy_from_user() were #ifdefed
out hence their EXPORT_SYMBOL() give an error message like:
.../riscv_ksyms.c:13:15: error: '__asm_copy_to_user' undeclared here
.../riscv_ksyms.c:14:15: error: '__asm_copy_from_user' undeclared here
Since these symbols are not defined with !MMU it's wrong to export them.
Same for __clear_user() (even though this one is also declared in
include/asm-generic/uaccess.h and thus doesn't give an error message).
Fix this by doing the EXPORT_SYMBOL() directly where these symbols
are defined: inside lib/uaccess.S itself.
Fixes: 3932ca301903 ("riscv: fix compile failure with EXPORT_SYMBOL() & !MMU") Reported-by: kbuild test robot <lkp@intel.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Linus Torvalds [Fri, 27 Dec 2019 21:21:06 +0000 (13:21 -0800)]
Merge tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Post-xmas food coma recovery fixes. Only three fixes for i915 since I
expect most people are holidaying.
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix"
* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Hold reference to intel_frontbuffer as we track activity
drm/i915/gt: Ratelimit display power w/a
drm/i915/pmu: Ensure monotonic rc6
Linus Torvalds [Fri, 27 Dec 2019 19:30:26 +0000 (11:30 -0800)]
Merge tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- rseq build failures fixes related to glibc 2.30 compatibility from
Mathieu Desnoyers
- Kunit fixes and cleanups from SeongJae Park
- Fixes to filesystems/epoll, firmware, and livepatch build failures
and skip handling.
* tag 'linux-kselftest-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
rseq/selftests: Clarify rseq_prepare_unload() helper requirements
rseq/selftests: Fix: Namespace gettid() for compatibility with glibc 2.30
rseq/selftests: Turn off timeout setting
kunit/kunit_tool_test: Test '--build_dir' option run
kunit: Rename 'kunitconfig' to '.kunitconfig'
kunit: Place 'test.log' under the 'build_dir'
kunit: Create default config in '--build_dir'
kunit: Remove duplicated defconfig creation
docs/kunit/start: Use in-tree 'kunit_defconfig'
selftests: livepatch: Fix it to do root uid check and skip
selftests: firmware: Fix it to do root uid check and skip
selftests: filesystems/epoll: fix build error
Linus Torvalds [Fri, 27 Dec 2019 19:26:54 +0000 (11:26 -0800)]
Merge tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
remove redundant Kconfig dependencies from multiple devfreq drivers
(Leonard Crestez)"
* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
Linus Torvalds [Fri, 27 Dec 2019 19:17:08 +0000 (11:17 -0800)]
Merge tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Removal of now unused busy wqe list (Hillf)
- Add cond_resched() to io-wq work processing (Hillf)
- And then the series that I hinted at from last week, which removes
the sqe from the io_kiocb and keeps all sqe handling on the prep
side. This guarantees that an opcode can't do the wrong thing and
read the sqe more than once. This is unchanged from last week, no
issues have been observed with this in testing. Hence I really think
we should fold this into 5.5.
* tag 'io_uring-5.5-20191226' of git://git.kernel.dk/linux-block:
io-wq: add cond_resched() to worker thread
io-wq: remove unused busy list from io_sqe
io_uring: pass in 'sqe' to the prep handlers
io_uring: standardize the prep methods
io_uring: read 'count' for IORING_OP_TIMEOUT in prep handler
io_uring: move all prep state for IORING_OP_{SEND,RECV}_MGS to prep handler
io_uring: move all prep state for IORING_OP_CONNECT to prep handler
io_uring: add and use struct io_rw for read/writes
io_uring: use u64_to_user_ptr() consistently
Linus Torvalds [Fri, 27 Dec 2019 19:09:04 +0000 (11:09 -0800)]
Merge tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Only thing here are the changes from Arnd from last week, which now
have the appropriate header include to ensure they actually compile if
COMPAT is enabled"
* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
compat_ioctl: block: handle Persistent Reservations
compat_ioctl: block: handle add zone open, close and finish ioctl
compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
pktcdvd: fix regression on 64-bit architectures
Linus Torvalds [Fri, 27 Dec 2019 19:02:48 +0000 (11:02 -0800)]
Merge tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A set of fixes for the v5.5 series:
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which is
causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and work
properly.
- Fix the Kconfig on the Tegra driver"
* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra186: Allow building on Tegra194-only configurations
gpio: pca953x: Switch to bitops in IRQ callbacks
gpiolib: fix up emulated open drain outputs
MAINTAINERS: Append missed file to the database
gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
gpio: aspeed: avoid return type warning
gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
gpio: Fix error message on out-of-range GPIO in lookup table
gpio: mpc8xxx: Add platform device to gpiochip->parent
gpio: xtensa: fix driver build
Florian Fainelli [Tue, 10 Dec 2019 18:53:47 +0000 (10:53 -0800)]
ata: ahci_brcm: Add missing clock management during recovery
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: bf3ea5501f7a ("ata: ahci_brcm: Recover from failures to identify devices") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms") Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Florian Fainelli [Tue, 10 Dec 2019 18:53:45 +0000 (10:53 -0800)]
ata: ahci_brcm: Fix AHCI resources management
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: 06b9d81d0b92 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Florian Fainelli [Tue, 10 Dec 2019 18:53:44 +0000 (10:53 -0800)]
ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()
This reverts commit d8d701c2c5c5ac117c3e1c8fc2088b35946993e2
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sascha Hauer [Fri, 13 Dec 2019 08:04:08 +0000 (09:04 +0100)]
libata: Fix retrieving of active qcs
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 3996a413557 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 3996a413557e ("libata: add extra internal command") Cc: stable@vger.kernel.org Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Merge tag 'devfreq-fixes-for-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux
Pull devfreq fixes for 5.5-rc4 from Chanwoo Choi:
"1. Fix the build error of tegra*-devfreq.c when COMPILE_TEST is enabled.
2. Drop unneeded PM_OPP dependency from each driver in Kconfig."
* tag 'devfreq-fixes-for-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
The rseq.h UAPI now documents that the rseq_cs field must be cleared
before reclaiming memory that contains the targeted struct rseq_cs, but
also that the rseq_cs field must be cleared before reclaiming memory of
the code pointed to by the rseq_cs start_ip and post_commit_offset
fields.
While we can expect that use of dlclose(3) will typically unmap
both struct rseq_cs and its associated code at once, nothing would
theoretically prevent a JIT from reclaiming the code without
reclaiming the struct rseq_cs, which would erroneously allow the
kernel to consider new code which is not a rseq critical section
as a rseq critical section following a code reclaim.
SeongJae Park [Fri, 20 Dec 2019 05:14:07 +0000 (05:14 +0000)]
kunit: Rename 'kunitconfig' to '.kunitconfig'
This commit renames 'kunitconfig' to '.kunitconfig' so that it can be
automatically ignored by git and do not disturb people who want to type
'kernel/' by pressing only the 'k' and then 'tab' key.
SeongJae Park [Fri, 20 Dec 2019 05:14:06 +0000 (05:14 +0000)]
kunit: Place 'test.log' under the 'build_dir'
'kunit' writes the 'test.log' under the kernel source directory even
though a 'build_dir' option is given. As users who use the option might
expect the outputs to be placed under the specified directory, this
commit modifies the logic to write the log file under the 'build_dir'.
SeongJae Park [Fri, 20 Dec 2019 05:14:05 +0000 (05:14 +0000)]
kunit: Create default config in '--build_dir'
If both '--build_dir' and '--defconfig' are given, the handling of
'--defconfig' ignores '--build_dir' option. This commit modifies the
behavior to respect '--build_dir' option.
SeongJae Park [Fri, 20 Dec 2019 05:14:04 +0000 (05:14 +0000)]
kunit: Remove duplicated defconfig creation
'--defconfig' option is handled by the 'main() of the 'kunit.py' but
again handled in following 'run_tests()'. This commit removes this
duplicated handling of the option in the 'run_tests()'.
SeongJae Park [Fri, 20 Dec 2019 05:14:03 +0000 (05:14 +0000)]
docs/kunit/start: Use in-tree 'kunit_defconfig'
The kunit doc suggests users to get the default `kunitconfig` from an
external git tree. However, the file is already located under the
`arch/um/configs/` of the kernel tree. Because the local file is easier
to access and maintain, this commit updates the doc to use it.
Shuah Khan [Mon, 16 Dec 2019 19:18:40 +0000 (12:18 -0700)]
selftests: livepatch: Fix it to do root uid check and skip
livepatch test configures the system and debug environment to run
tests. Some of these actions fail without root access and test
dumps several permission denied messages before it exits.
Fix test-state.sh to call setup_config instead of set_dynamic_debug
as suggested by Petr Mladek <pmladek@suse.com>
Fix it to check root uid and exit with skip code instead.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Acked-by: Joe Lawrence <joe.lawrence@redhat.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Shuah Khan [Fri, 13 Dec 2019 01:56:06 +0000 (18:56 -0700)]
selftests: firmware: Fix it to do root uid check and skip
firmware attempts to load test modules that require root access
and fail. Fix it to check for root uid and exit with skip code
instead.
Before this fix:
selftests: firmware: fw_run_tests.sh
modprobe: ERROR: could not insert 'test_firmware': Operation not permitted
You must have the following enabled in your kernel:
CONFIG_TEST_FIRMWARE=y
CONFIG_FW_LOADER=y
CONFIG_FW_LOADER_USER_HELPER=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
With this fix:
selftests: firmware: fw_run_tests.sh
skip all tests: must be run as root
not ok 1 selftests: firmware: fw_run_tests.sh # SKIP
Shuah Khan [Wed, 11 Dec 2019 00:12:33 +0000 (17:12 -0700)]
selftests: filesystems/epoll: fix build error
epoll build fails to find pthread lib. Fix Makefile to use LDLIBS
instead of LDFLAGS. LDLIBS is the right flag to use here with -l
option when invoking ld.
gcc -I../../../../../usr/include/ -lpthread epoll_wakeup_test.c -o .../tools/testing/selftests/filesystems/epoll/epoll_wakeup_test
/usr/bin/ld: /tmp/ccaZvJUl.o: in function `kill_timeout':
epoll_wakeup_test.c:(.text+0x4dd): undefined reference to `pthread_kill'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x4f2): undefined reference to `pthread_kill'
/usr/bin/ld: /tmp/ccaZvJUl.o: in function `epoll9':
epoll_wakeup_test.c:(.text+0x6382): undefined reference to `pthread_create'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x64d2): undefined reference to `pthread_create'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6626): undefined reference to `pthread_join'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x684c): undefined reference to `pthread_tryjoin_np'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6864): undefined reference to `pthread_kill'
/usr/bin/ld: epoll_wakeup_test.c:(.text+0x6878): undefined reference to `pthread_join'
Hillf Danton [Sun, 22 Dec 2019 14:46:54 +0000 (22:46 +0800)]
io-wq: remove unused busy list from io_sqe
Commit 5546fb621638 ("io-wq: ensure free/busy list browsing see all
items") added a list for io workers in addition to the free and busy
lists, not only making worker walk cleaner, but leaving the busy list
unused. Let's remove it.
When listing a directory with thounsands of files and most of them are
reparse points, we simply marked all those dentries for revalidation
and then sending additional (compounded) create/getinfo/close requests
for each of them.
Instead, upon receiving a response from an SMB2_QUERY_DIRECTORY
(FileIdFullDirectoryInformation) command, the directory entries that
have a file attribute of FILE_ATTRIBUTE_REPARSE_POINT will contain an
EaSize field with a reparse tag in it, so we parse it and mark the
dentry for revalidation only if it is a DFS or a symlink.
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
../fs/cifs/smb2file.c:70:3: warning: misleading indentation; statement
is not part of the previous 'if' [-Wmisleading-indentation]
if (oparms->tcon->use_resilient) {
^
../fs/cifs/smb2file.c:66:2: note: previous statement is here
if (rc)
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: abc22a45d3b8 ("Add resilienthandles mount parm") Link: https://github.com/ClangBuiltLinux/linux/issues/826 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Chris Wilson [Wed, 18 Dec 2019 10:40:43 +0000 (10:40 +0000)]
drm/i915: Hold reference to intel_frontbuffer as we track activity
Since obj->frontbuffer is no longer protected by the struct_mutex, as we
are processing the execbuf, it may be removed. Mark the
intel_frontbuffer as rcu protected, and so acquire a reference to
the struct as we track activity upon it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/827 Fixes: d6f402fc3b7e ("drm/i915: Extract intel_frontbuffer active tracking") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Matthew Auld <matthew.auld@intel.com> Cc: <stable@vger.kernel.org> # v5.4+ Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191218104043.3539458-1-chris@chris-wilson.co.uk
(cherry picked from commit da42104f589d979bbe402703fd836cec60befae1) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Wed, 18 Dec 2019 09:35:04 +0000 (09:35 +0000)]
drm/i915/gt: Ratelimit display power w/a
For very light workloads that frequently park, acquiring the display
power well (required to prevent the dmc from trashing the system) takes
longer than the execution. A good example is the igt_coherency selftest,
which is slowed down by an order of magnitude in the worst case with
powerwell cycling. To prevent frequent cycling, while keeping our fast
soft-rc6, use a timer to delay release of the display powerwell.
First is not assuming rc6 value zero means GT is asleep since that can
also mean GPU is fully busy and we do not want to enter the estimation
path in that case.
Second is ensuring monotonicity on the estimation path itself. I suspect
what is happening is with extremely rapid park/unpark cycles we get no
updates on the real rc6 and therefore have to careful not to
unconditionally trust use last known real rc6 when creating a new
estimation.
v2:
* Simplify logic by not tracking the estimate but last reported value.
Leonard Crestez [Mon, 11 Nov 2019 18:16:10 +0000 (20:16 +0200)]
PM / devfreq: Drop explicit selection of PM_OPP
CONFIG_PM_OPP is already selected by CONFIG_PM_DEVFREQ
since commit 71f74a36bded ("PM / devfreq: Add dependency on PM_OPP").
This means that individual drivers shouldn't "select PM_OPP" explicitly.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[cw00.choi: Edit the patch title] Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Linus Torvalds [Sun, 22 Dec 2019 18:59:06 +0000 (10:59 -0800)]
Merge tag 'xfs-5.5-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Fix a few bugs that could lead to corrupt files, fsck complaints, and
filesystem crashes:
- Minor documentation fixes
- Fix a file corruption due to read racing with an insert range
operation.
- Fix log reservation overflows when allocating large rt extents
- Fix a buffer log item flags check
- Don't allow administrators to mount with sunit= options that will
cause later xfs_repair complaints about the root directory being
suspicious because the fs geometry appeared inconsistent
- Fix a non-static helper that should have been static"
* tag 'xfs-5.5-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Make the symbol 'xfs_rtalloc_log_count' static
xfs: don't commit sunit/swidth updates to disk if that would cause repair failures
xfs: split the sunit parameter update into two parts
xfs: refactor agfl length computation function
libxfs: resync with the userspace libxfs
xfs: use bitops interface for buf log item AIL flag check
xfs: fix log reservation overflows when allocating large rt extents
xfs: stabilize insert range start boundary to avoid COW writeback race
xfs: fix Sphinx documentation warning
Linus Torvalds [Sun, 22 Dec 2019 18:41:48 +0000 (10:41 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Ext4 bug fixes, including a regression fix"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: clarify impact of 'commit' mount option
ext4: fix unused-but-set-variable warning in ext4_add_entry()
jbd2: fix kernel-doc notation warning
ext4: use RCU API in debug_print_tree
ext4: validate the debug_want_extra_isize mount option at parse time
ext4: reserve revoke credits in __ext4_new_inode
ext4: unlock on error in ext4_expand_extra_isize()
ext4: optimize __ext4_check_dir_entry()
ext4: check for directory entries too close to block end
ext4: fix ext4_empty_dir() for directories with holes
Linus Torvalds [Sun, 22 Dec 2019 18:36:55 +0000 (10:36 -0800)]
Merge tag 'block-5.5-20191221' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Let's try this one again, this time without the compat_ioctl changes.
We've got those fixed up, but that can go out next week.
This contains:
- block queue flush lockdep annotation (Bart)
- Type fix for bsg_queue_rq() (Bart)
- Three dasd fixes (Stefan, Jan)
- nbd deadlock fix (Mike)
- Error handling bio user map fix (Yang)
- iocost fix (Tejun)
- sbitmap waitqueue addition fix that affects the kyber IO scheduler
(David)"
* tag 'block-5.5-20191221' of git://git.kernel.dk/linux-block:
sbitmap: only queue kyber's wait callback if not already active
block: fix memleak when __blk_rq_map_user_iov() is failed
s390/dasd: fix typo in copyright statement
s390/dasd: fix memleak in path handling error case
s390/dasd/cio: Interpret ccw_device_get_mdc return value correctly
block: Fix a lockdep complaint triggered by request queue flushing
block: Fix the type of 'sts' in bsg_queue_rq()
block: end bio with BLK_STS_AGAIN in case of non-mq devs and REQ_NOWAIT
nbd: fix shutdown and recv work deadlock v2
iocost: over-budget forced IOs should schedule async delay
- Fix scratch register clearing in M-mode (affects nommu users)
- Fix a mismerge on my part that broke the build for
CONFIG_SPARSEMEM_VMEMMAP users
Cleanup:
- Move SiFive L2 cache-related code to drivers/soc, per request"
* tag 'riscv/for-v5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: move sifive_l2_cache.c to drivers/soc
riscv: define vmemmap before pfn_to_page calls
riscv: fix scratch register clearing in M-mode.
riscv: Fix use of undefined config option CONFIG_CONFIG_MMU
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
Jan Stancek [Sun, 22 Dec 2019 12:33:24 +0000 (13:33 +0100)]
pipe: fix empty pipe check in pipe_write()
LTP pipeio_1 test is hanging with v5.5-rc2-385-gb8e382a185eb,
with read side observing empty pipe and sleeping and write
side running out of space and then sleeping as well. In this
scenario there are 5 writers and 1 reader.
Problem is that after pipe_write() reacquires pipe lock, it
re-checks for empty pipe with potentially stale 'head' and
doesn't wake up read side anymore. pipe->tail can advance
beyond 'head', because there are multiple writers.
Use pipe->head for empty pipe check after reacquiring lock
to observe current state.
Testing: With patch, LTP pipeio_1 ran successfully in loop for 1 hour.
Without patch it hanged within a minute.
Paolo Bonzini [Wed, 4 Dec 2019 14:33:35 +0000 (15:33 +0100)]
MAINTAINERS: remove Radim from KVM maintainers
Radim's kernel.org email is bouncing, which I take as a signal that
he is not really able to deal with KVM at this time. Make MAINTAINERS
match the effective value of KVM's bus factor.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
James Hogan [Sat, 21 Dec 2019 15:50:13 +0000 (15:50 +0000)]
MAINTAINERS: Orphan KVM for MIPS
I haven't been active for 18 months, and don't have the hardware set up
to test KVM for MIPS, so mark it as orphaned and remove myself as
maintainer. Hopefully somebody from MIPS can pick this up.
Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: kvm@vger.kernel.org Cc: linux-mips@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yunfeng Ye [Tue, 17 Dec 2019 14:46:49 +0000 (22:46 +0800)]
ext4: fix unused-but-set-variable warning in ext4_add_entry()
Warning is found when compile with "-Wunused-but-set-variable":
fs/ext4/namei.c: In function ‘ext4_add_entry’:
fs/ext4/namei.c:2167:23: warning: variable ‘sbi’ set but not used
[-Wunused-but-set-variable]
struct ext4_sb_info *sbi;
^~~
Fix this by moving the variable @sbi under CONFIG_UNICODE.
Linus Torvalds [Sat, 21 Dec 2019 23:16:56 +0000 (15:16 -0800)]
Merge tag 'trace-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix memory leak on error path of process_system_preds()
- Lock inversion fix with updating tgid recording option
- Fix histogram compare function on big endian machines
- Fix histogram trigger function on big endian machines
- Make trace_printk() irq sync on init for kprobe selftest correctness
* tag 'trace-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix endianness bug in histogram trigger
samples/trace_printk: Wait for IRQ work to finish
tracing: Fix lock inversion in trace_event_enable_tgid_record()
tracing: Have the histogram compare functions convert to u64 first
tracing: Avoid memory leak in process_system_preds()
Linus Torvalds [Sat, 21 Dec 2019 23:12:26 +0000 (15:12 -0800)]
Merge tag 'libnvdimm-fix-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Dan Williams:
"A minor regression fix.
The libnvdimm unit tests were expecting to mock calls to
ioremap_nocache() which disappeared in v5.5-rc1. This fix has appeared
in -next and collided with some cleanups that Christoph has planned
for v5.6, but he will fix up his branch once this goes in.
Summary:
- Restore the operation of the libnvdimm unit tests after the removal
of ioremap_nocache()"
* tag 'libnvdimm-fix-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
tools/testing/nvdimm: Fix mock support for ioremap
Sven Schnelle [Wed, 18 Dec 2019 07:44:27 +0000 (08:44 +0100)]
tracing: Fix endianness bug in histogram trigger
At least on PA-RISC and s390 synthetic histogram triggers are failing
selftests because trace_event_raw_event_synth() always writes a 64 bit
values, but the reader expects a field->size sized value. On little endian
machines this doesn't hurt, but on big endian this makes the reader always
read zero values.
Link: http://lore.kernel.org/linux-trace-devel/20191218074427.96184-4-svens@linux.ibm.com Cc: stable@vger.kernel.org Fixes: 00a1b9a7a86b6 ("tracing: Add support for 'synthetic' events") Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com> Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This gives a circular dependency deadlock between trace_types_lock and
event_mutex. To fix this invert the usage of trace_types_lock and
event_mutex in trace_options_core_write(). This keeps the sequence of
lock usage consistent.
Linus Torvalds [Sat, 21 Dec 2019 20:17:14 +0000 (12:17 -0800)]
Merge tag 's390-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix unwinding from irq context of interrupted user process.
- Add purgatory build missing symbols check. That helped to uncover and
fix missing symbols when built with kasan support enabled.
- Couple of ftrace fixes. Avoid broken stack trace and fix recursion
loop in function_graph tracer.
* tag 's390-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ftrace: save traced function caller
s390/unwind: stop gracefully at user mode pt_regs in irq stack
s390/purgatory: do not build purgatory with kcov, kasan and friends
s390/purgatory: Make sure we fail the build if purgatory has missing symbols
s390/ftrace: fix endless recursion in function_graph tracer
Linus Torvalds [Sat, 21 Dec 2019 18:52:10 +0000 (10:52 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: a (rare) PSI crash fix, a CPU affinity related balancing
fix, and a toning down of active migration attempts"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cfs: fix spurious active migration
sched/fair: Fix find_idlest_group() to handle CPU affinity
psi: Fix a division error in psi poll()
sched/psi: Fix sampling error and rare div0 crashes with cgroups and high uptime
Linus Torvalds [Sat, 21 Dec 2019 18:51:00 +0000 (10:51 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: a BTS fix, a PT NMI handling fix, a PMU sysfs fix and an
SRCU annotation"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Add SRCU annotation for pmus list walk
perf/x86/intel: Fix PT PMI handling
perf/x86/intel/bts: Fix the use of page_private()
perf/x86: Fix potential out-of-bounds access
Linus Torvalds [Sat, 21 Dec 2019 18:49:47 +0000 (10:49 -0800)]
Merge tag 'kbuild-fixes-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix warning in out-of-tree 'make clean'
- add READELF variable to the top Makefile
- fix broken builds when LINUX_COMPILE_BY contains a backslash
- fix build warning in kallsyms
- fix NULL pointer access in expr_eq() in Kconfig
- fix missing dependency on rsync in deb-pkg build
- remove ---help--- from documentation
- fix misleading documentation about directory descending
* tag 'kbuild-fixes-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: clarify the difference between obj-y and obj-m w.r.t. descending
kconfig: remove ---help--- from documentation
scripts: package: mkdebian: add missing rsync dependency
kconfig: don't crash on NULL expressions in expr_eq()
scripts/kallsyms: fix offset overflow of kallsyms_relative_base
mkcompile_h: use printf for LINUX_COMPILE_BY
mkcompile_h: git rid of UTS_TRUNCATE from LINUX_COMPILE_{BY,HOST}
x86/boot: kbuild: allow readelf executable to be specified
kbuild: fix 'No such file or directory' warning when cleaning
projects / kernel.git / log