The TI J721E EVM base board has TI DP83867 PHY connected to external CPSW
NUSS Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI j721e SoC MCU
Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT node for The TI J721E MCU SoC Gigabit Ethernet
subsystem (MCU CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
AM654 EVM base board has TI DP83867 PHY connected to external CPSW NUSS
Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI am654 SoC Gigabit
Ethernet two ports Switch subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT node for the TI AM65x SoC Gigabit Ethernet two ports Switch
subsystem (CPSW NUSS).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver
The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) with selectable RGMII and RMII
interfaces and an internal Communications Port Programming Interface (CPPI)
port (Host port 0) and with ALE in between. It also contains
- Management Data Input/Output (MDIO) interface for physical layer device
(PHY) management;
- Updated Address Lookup Engine (ALE) module;
- (TBD) New version of Common platform time sync (CPTS) module.
On the TI am65x/J721E SoCs CPSW NUSS Ethernet subsystem into device MCU
domain named MCU_CPSW0.
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and one RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.
Introduced driver provides standard Linux net_device to user space and supports:
- ifconfig up/down
- MAC address configuration
- ethtool operation:
--driver
--change
--register-dump
--negotiate phy
--statistics
--set-eee phy
--show-ring
--show-channels
--set-channels
- net_device ioctl mii-control
- promisc mode
- rx checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets.
The CPSW NUSS can verify IPv4/IPv6 TCP/UDP packets checksum and fills
csum information for each packet in psdata[2] word:
- BIT(16) CHECKSUM_ERROR - indicates csum error
- BIT(17) FRAGMENT - indicates fragmented packet
- BIT(18) TCP_UDP_N - Indicates TCP packet was detected
- BIT(19) IPV6_VALID, BIT(20) IPV4_VALID - indicates IPv6/IPv4 packet
- BIT(15, 0) CHECKSUM_ADD - This is the value that was summed
during the checksum computation. This value is FFFFh for non fragmented
IPV4/6 UDP/TCP packets with no checksum error.
RX csum offload can be disabled:
ethtool -K <dev> rx-checksum on|off
- tx checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).
TX csum HW offload can be enabled/disabled:
ethtool -K <dev> tx-checksum-ip-generic on|off
- multiq and switch between round robin/prio modes for cppi tx queues by
using Netdev private flag "p0-rx-ptype-rrobin" to switch between
Round Robin and Fixed priority modes:
# ethtool --show-priv-flags eth0
Private flags for eth0:
p0-rx-ptype-rrobin: on
# ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off
Number of TX DMA channels can be changed using "ethtool -L eth0 tx <N>".
- GRO support: the napi_gro_receive() and napi_complete_done() are used.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Document device tree bindings for The TI AM654x/J721E SoC Gigabit Ethernet MAC
(Media Access Controller - CPSW2G NUSS). The CPSW NUSS provides Ethernet packet
communication for the device.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Rob Herring <robh@kernel.org> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ti: ale: am65: add support for default thread cfg
Add support for default thread configuration for AM65x CPSW NUSS ALE to
allow route all ingress packets to one default RX UDMA flow.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ti: ale: add support for mac-only mode
The new CPSW ALE version, available on TI K3 AM654/J721E SoCs family,
allows to switch any external port to MAC only mode. When MAC only mode
enabled this port be treated like a MAC port for the host. All traffic
received is only sent to the host. The host must direct traffic to this
port as the lookup engine will not send traffic to the ports with the
p0_maconly bit set and the p0_no_learn also set. If p0_maconly bit is set
and the p0_no_learn is not set, the host can send non-directed packets that
can be sent to the destination of a MacOnly port. It is also possible that
The host can broadcast to all ports including MacOnly ports in this mode.
This patch add ALE supprt for MAC only mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled
On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS the unregistered multicast
packets are still can be received with promisc and allmulti disabled.
This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
ALE VLAN entry:UNREG_MCAST_FLOOD_INDEX -> ALE_VLAN_MASK_MUXx
ALE VLAN entry:REG_MCAST_FLOOD_INDEX -> ALE_VLAN_MASK_MUXy
The commit e479b3d4b48b ("net: netcp: ale: add proper ale entry mask bits
for netcp switch ALE") update ALE code to support such ALE entries, it is
always used ALE_VLAN_MASK_MUX0_REG index in ALE VLAN entry for unreg mcast
packets mask configuration, which is read-only, at least for AM65xx MCU
CPSW2G NUSS and 66AK2E/L NUSS. As result unreg mcast packets are allowed
always.
Hence, update ALE code to use ALE_VLAN_MASK_MUX1_REG index for ALE VLAN
entries to configure unreg mcast port mask.
Fixes: e479b3d4b48b ("net: netcp: ale: add proper ale entry mask bits for netcp switch ALE") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
phy: ti: gmii-sel: simplify config dependencies between net drivers and gmii phy
The phy-gmii-sel can be only auto selected in Kconfig and now the pretty
complex Kconfig dependencies are defined for phy-gmii-sel driver, which
also need to be updated every time phy-gmii-sel is re-used for any new
networking driver.
Simplify Kconfig definition for phy-gmii-sel PHY driver - drop all
dependencies and from networking drivers and rely on using 'imply
PHY_TI_GMII_SEL' in Kconfig definitions for networking drivers instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Kishon Vijay Abraham I <kishon@ti.com> Tested-by: Murali Karicheri <m-karicheri2@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Mon, 23 Mar 2020 20:48:51 +0000 (21:48 +0100)]
cls_flower: Add extack support for src and dst port range options
Pass extack down to fl_set_key_port_range() and set message on error.
Both the min and max ports would qualify as invalid attributes here.
Report the min one as invalid, as it's probably what makes the most
sense from a user point of view.
Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: net: add marvell usb to mdio bindings
Describe how the USB to MDIO controller can optionally use device tree
bindings to reference attached devices such as switches.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
then we expect the PHY driver to be bound to the phydev when triggering
the action. This may not be the case in case of asynchronous probing.
Therefore ensure that PHY drivers are probed synchronously.
Default still is sync probing, except async probing is explicitly
requested. I saw some comments that the intention is to promote
async probing for more parallelism in boot process and want to be
prepared for the case that the default is changed to async probing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds support for the DEVLINK_CMD_REGION_NEW operation, used to
enable userspace requesting a snapshot of a region on demand.
This can be useful to enable adding regions for a driver for which there is
no trigger to create snapshots. By making this a core part of devlink, there
is no need for the drivers to use a separate channel such as debugfs.
The primary intent for this kind of region is to expose device information
that might be useful for diagnostics and information gathering.
The first few patches refactor regions to support a new ops structure for
extending the available operations that regions can perform. This includes
converting the destructor into an op from a function argument.
Next, patches refactor the snapshot id allocation to use an xarray which
tracks the number of current snapshots using a given id. This is done so
that id lifetime can be determined, and ids can be released when no longer
in use.
Without this change, snapshot ids remain used forever, until the snapshot_id
count rolled over UINT_MAX.
Finally, code to enable the previously unused DEVLINK_CMD_REGION_NEW is
added. This code enforces that the snapshot id is always provided, unlike
previous revisions of this series.
Finally, a patch is added to enable using this new command via the .snapshot
callback in both netdevsim and the ice driver.
For the ice driver, a new "nvm-flash" region is added, which will enable
read access to the NVM flash contents. The intention for this is to allow
diagnostics tools to gather information about the device. By using a
snapshot and gathering the NVM contents all at once, the contents can be
atomic.
Major changes since RFC:
* use an xarray for tracking snapshot ids, rather than an IDR
* remove support for auto-generated snapshot ids in DEVLINK_CMD_REGION_NEW
See each patch for an individual changelog per-patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:18 +0000 (11:37 -0700)]
ice: add a devlink region for dumping NVM contents
Add a devlink region for exposing the device's Non Volatime Memory flash
contents.
Support the recently added .snapshot operation, enabling userspace to
request a snapshot of the NVM contents via DEVLINK_CMD_REGION_NEW.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:17 +0000 (11:37 -0700)]
netdevsim: support taking immediate snapshot via devlink
Implement the .snapshot region operation for the dummy data region. This
enables a region snapshot to be taken upon request via the new
DEVLINK_CMD_REGION_SNAPSHOT command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:16 +0000 (11:37 -0700)]
devlink: implement DEVLINK_CMD_REGION_NEW
Implement support for the DEVLINK_CMD_REGION_NEW command for creating
snapshots. This new command parallels the existing
DEVLINK_CMD_REGION_DEL.
In order for DEVLINK_CMD_REGION_NEW to work for a region, the new
".snapshot" operation must be implemented in the region's ops structure.
The desired snapshot id must be provided. This helps avoid confusion on
the purpose of DEVLINK_CMD_REGION_NEW, and keeps the API simpler.
The requested id will be inserted into the xarray tracking the number of
snapshots using each id. If this id is already used by another snapshot
on any region, an error will be returned.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:15 +0000 (11:37 -0700)]
devlink: track snapshot id usage count using an xarray
Each snapshot created for a devlink region must have an id. These ids
are supposed to be unique per "event" that caused the snapshot to be
created. Drivers call devlink_region_snapshot_id_get to obtain a new id
to use for a new event trigger. The id values are tracked per devlink,
so that the same id number can be used if a triggering event creates
multiple snapshots on different regions.
There is no mechanism for snapshot ids to ever be reused. Introduce an
xarray to store the count of how many snapshots are using a given id,
replacing the snapshot_id field previously used for picking the next id.
The devlink_region_snapshot_id_get() function will use xa_alloc to
insert an initial value of 1 value at an available slot between 0 and
U32_MAX.
The new __devlink_snapshot_id_increment() and
__devlink_snapshot_id_decrement() functions will be used to track how
many snapshots currently use an id.
Drivers must now call devlink_snapshot_id_put() in order to release
their reference of the snapshot id after adding region snapshots.
By tracking the total number of snapshots using a given id, it is
possible for the decrement() function to erase the id from the xarray
when it is not in use.
With this method, a snapshot id can become reused again once all
snapshots that referred to it have been deleted via
DEVLINK_CMD_REGION_DEL, and the driver has finished adding snapshots.
This work also paves the way to introduce a mechanism for userspace to
request a snapshot.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:14 +0000 (11:37 -0700)]
devlink: report error once U32_MAX snapshot ids have been used
The devlink_snapshot_id_get() function returns a snapshot id. The
snapshot id is a u32, so there is no way to indicate an error code.
A future change is going to possibly add additional cases where this
function could fail. Refactor the function to return the snapshot id in
an argument, so that it can return zero or an error value.
This ensures that snapshot ids cannot be confused with error values, and
aids in the future refactor of snapshot id allocation management.
Because there is no current way to release previously used snapshot ids,
add a simple check ensuring that an error is reported in case the
snapshot_id would over flow.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:13 +0000 (11:37 -0700)]
devlink: extract snapshot id allocation to helper function
A future change is going to implement a new devlink command to request
a snapshot on demand. As part of this, the logic for handling the
snapshot ids will be refactored. To simplify the snapshot id allocation
function, move it to a separate function prefixed by `__`. This helper
function will assume the lock is held.
While no other callers will exist, it simplifies refactoring the logic
because there is no need to complicate the function with gotos to handle
unlocking on failure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:12 +0000 (11:37 -0700)]
devlink: use -ENOSPC to indicate no more room for snapshots
The devlink_region_snapshot_create function returns -ENOMEM when the
maximum number of snapshots has been reached. This is confusing because
it is not an issue of being out of memory. Change this to use -ENOSPC
instead.
Reported-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:11 +0000 (11:37 -0700)]
devlink: add function to take snapshot while locked
A future change is going to add a new devlink command to request
a snapshot on demand. This function will want to call the
devlink_region_snapshot_create function while already holding the
devlink instance lock.
Extract the logic of this function into a static function prefixed by
`__` to indicate that it is an internal helper function. Modify the
original function to be implemented in terms of the new locked
function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:10 +0000 (11:37 -0700)]
devlink: trivial: fix tab in function documentation
The function documentation comment for devlink_region_snapshot_create
included a literal tab character between 'future analyses' that was
difficult to spot as it happened to only display as one space wide.
Fix the comment to use a space here instead of a stray tab appearing in
the middle of a sentence.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:09 +0000 (11:37 -0700)]
devlink: convert snapshot destructor callback to region op
It does not makes sense that two snapshots for a given region would use
different destructors. Simplify snapshot creation by adding
a .destructor op for regions.
This operation will replace the data_destructor for the snapshot
creation, and makes snapshot creation easier.
Noticed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Thu, 26 Mar 2020 18:37:08 +0000 (11:37 -0700)]
devlink: prepare to support region operations
Modify the devlink region code in preparation for adding new operations
on regions.
Create a devlink_region_ops structure, and move the name pointer from
within the devlink_region structure into the ops structure (similar to
the devlink_health_reporter_ops).
This prepares the regions to enable support of additional operations in
the future such as requesting snapshots, or accessing the region
directly without a snapshot.
In order to re-use the constant strings in the mlx4 driver their
declaration must be changed to 'const char * const' to ensure the
compiler realizes that both the data and the pointer cannot change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Thu, 26 Mar 2020 22:10:20 +0000 (23:10 +0100)]
veth: rely on peer veth_rq for ndo_xdp_xmit accounting
Rely on 'remote' veth_rq to account ndo_xdp_xmit ethtool counters.
Move XDP_TX accounting to veth_xdp_flush_bq routine.
Remove 'rx' prefix in rx xdp ethool counters
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lorenzo Bianconi [Thu, 26 Mar 2020 22:10:19 +0000 (23:10 +0100)]
veth: rely on veth_rq in veth_xdp_flush_bq signature
Substitute net_device point with veth_rq one in veth_xdp_flush_bq,
veth_xdp_flush and veth_xdp_tx signature. This is a preliminary patch
to account xdp_xmit counter on 'receiving' veth_rq
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Implement stats_update callback for pedit and skbedit
The stats_update callback is used for adding HW counters to the SW ones.
Both skbedit and pedit actions are actually recognized by flow_offload.h,
but do not implement these callbacks. As a consequence, the reported values
are only the SW ones, even where there is a HW counter available.
Patch #1 adds the callback to action skbedit, patch #2 adds it to action
pedit. Patch #3 tweaks an skbedit selftest with a check that would have
caught this problem.
The pedit test is not likewise tweaked, because the iproute2 pedit action
currently does not support JSON dumping. This will be addressed later.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 26 Mar 2020 20:45:57 +0000 (22:45 +0200)]
selftests: skbedit_priority: Test counters at the skbedit rule
Currently the test checks the observable effect of skbedit priority:
queueing of packets at the correct qdisc band. It therefore misses the fact
that the counters for offloaded rules are not updated. Add an extra check
for the counter.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 26 Mar 2020 20:45:56 +0000 (22:45 +0200)]
sched: act_pedit: Implement stats_update callback
Implement this callback in order to get the offloaded stats added to the
kernel stats.
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Implement this callback in order to get the offloaded stats added to the
kernel stats.
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum switches allow packet prioritization based on DSCP on ingress,
and update of DSCP on egress. This is configured through the DCB APP rules.
For some use cases, assigning a custom DSCP value based on an ACL match is
a better tool. To that end, offload FLOW_ACTION_MANGLE to permit changing
of dsfield as a whole, or DSCP and ECN values in isolation.
After fixing a commentary nit in patch #1, and mlxsw naming in patch #2,
patches #3 and #4 add the offload to mlxsw.
Patch #5 adds a forwarding selftest for pedit dsfield, applicable to SW as
well as HW datapaths. Patch #6 adds a mlxsw-specific test to verify DSCP
rewrite due to DCB APP rules is not performed on pedited packets.
The tests only cover IPv4 dsfield setting. We have tests for IPv6 as well,
but would like to postpone their contribution until the corresponding
iproute patches have been accepted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 26 Mar 2020 14:01:14 +0000 (16:01 +0200)]
selftests: mlxsw: qos_dscp_router: Test no DSCP rewrite after pedit
When DSCP is updated through an offloaded pedit action, DSCP rewrite on
egress should be disabled. Add a test that check that it is so.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 26 Mar 2020 14:01:13 +0000 (16:01 +0200)]
selftests: forwarding: Add a forwarding test for pedit munge dsfield
Add a test that runs packets with dsfield set, and test that pedit adjusts
the DSCP or ECN parts or the whole field.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Offload action pedit ex munge when used with a flower classifier. Only
allow setting of DSCP, ECN, or the whole DSField in IPv4 and IPv6 packets.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 26 Mar 2020 14:01:11 +0000 (16:01 +0200)]
mlxsw: core: Add DSCP, ECN, dscp_rw to QOS_ACTION
The QOS_ACTION is used for manipulating the QOS attributes of the packet.
Add the defines and helpers related to DSCP and ECN fields, and dscp_rw.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 26 Mar 2020 14:01:10 +0000 (16:01 +0200)]
mlxsw: core: Rename mlxsw_afa_qos_cmd to mlxsw_afa_qos_switch_prio_cmd
The original idea was to reuse this set of actions for ECN rewrite as well,
but on second look, it's not such a great idea. These two items should each
have its own command. Rename the existing enum to make it obvious that it
belongs to switch_prio_cmd.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Thu, 26 Mar 2020 14:01:09 +0000 (16:01 +0200)]
net: flow_offload.h: Fix a comment at flow_action_entry.mangle
This field references FLOW_ACTION_PACKET_EDIT. Such action does not exist
though. Instead the field is used for FLOW_ACTION_MANGLE and _ADD.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 26 Mar 2020 03:21:50 +0000 (11:21 +0800)]
atl2: remove unused variable 'atl2_driver_string'
drivers/net/ethernet/atheros/atlx/atl2.c:40:19: warning: ‘atl2_driver_string’ defined but not used [-Wunused-const-variable=]
static const char atl2_driver_string[] = "Atheros(R) L2 Ethernet Driver";
^~~~~~~~~~~~~~~~~~
commit 413afd8e9705 ("net/atheros: Clean atheros code from driver version")
left behind this, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hoang Le [Thu, 26 Mar 2020 02:50:29 +0000 (09:50 +0700)]
tipc: Add a missing case of TIPC_DIRECT_MSG type
In the commit 5248c6f8694f
("tipc: improve throughput between nodes in netns"), we're missing a check
to handle TIPC_DIRECT_MSG type, it's still using old sending mechanism for
this message type. So, throughput improvement is not significant as
expected.
Besides that, when sending a large message with that type, we're also
handle wrong receiving queue, it should be enqueued in socket receiving
instead of multicast messages.
Fix this by adding the missing case for TIPC_DIRECT_MSG.
Fixes: 5248c6f8694f ("tipc: improve throughput between nodes in netns") Reported-by: Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hence, they are synchronized using a new mode_lock.
eswitch's state_lock is not used as it can lead to a deadlock scenario
below and state_lock is only for vport and fdb exclusive access.
ip link set vf <param>
netlink rcv_msg() - Lock A
rtnl_lock
vfinfo()
esw->state_lock() - Lock B
devlink eswitch_set
devlink_mutex
esw->state_lock() - Lock B
attach_netdev()
register_netdev()
rtnl_lock - Lock A
Alternatives considered:
1. Acquiring rtnl lock before taking esw->state_lock to follow similar
locking sequence as ip link flow during eswitch mode set.
rtnl lock is not good idea for two reasons.
(a) Holding rtnl lock for several hundred device commands is not good
idea.
(b) It leads to below and more similar deadlocks.
devlink eswitch_set
devlink_mutex
rtnl_lock - Lock A
esw->state_lock() - Lock B
eswitch_disable()
reload()
ib_register_device()
ib_cache_setup_one()
rtnl_lock()
2. Exporting devlink lock may lead to undesired use of it in vendor
driver(s) in future.
3. Unloading representors outside of the mode_lock requires
serialization with other process trying to enable the eswitch.
4. Differing the representors life cycle to a different workqueue
requires synchronization with func_change_handler workqueue.
Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Bodong Wang <bodong@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Parav Pandit [Wed, 18 Dec 2019 10:58:58 +0000 (04:58 -0600)]
net/mlx5: E-switch, Extend eswitch enable to handle num_vfs change
Subsequent patch protects eswitch mode changes across sriov and devlink
interfaces. It is desirable for eswitch to provide thread safe eswitch
enable and disable APIs.
Hence, extend eswitch enable API to optionally update num_vfs when
requested.
In subsequent patch, eswitch num_vfs are updated after all the eswitch
users eswitch drops its reference count.
Reviewed-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Bodong Wang <bodong@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Parav Pandit [Mon, 24 Feb 2020 01:06:56 +0000 (19:06 -0600)]
devlink: Rely on driver eswitch thread safety instead of devlink
devlink_nl_cmd_eswitch_set_doit() doesn't hold devlink->lock mutex while
invoking driver callback. This is likely due to eswitch mode setting
involves adding/remove devlink ports, health reporters or
other devlink objects for a devlink device.
So it is driver responsiblity to ensure thread safe eswitch state
transition happening via either sriov legacy enablement or via devlink
eswitch set callback.
Therefore, get() callback should also be invoked without holding
devlink->lock mutex.
Vendor driver can use same internal lock which it uses during eswitch
mode set() callback.
This makes get() and set() implimentation symmetric in devlink core and
in vendor drivers.
Hence, remove holding devlink->lock mutex during eswitch get() callback.
Failing to do so results into below deadlock scenario when mlx5_core
driver is improved to handle eswitch mode set critical section invoked
by devlink and sriov sysfs interface in subsequent patch.
devlink_nl_cmd_eswitch_set_doit()
mlx5_eswitch_mode_set()
mutex_lock(esw->mode_lock) <- Lock A
[...]
register_devlink_port()
mutex_lock(&devlink->lock); <- lock B
mutex_lock(&devlink->lock); <- lock B
devlink_nl_cmd_eswitch_get_doit()
mlx5_eswitch_mode_get()
mutex_lock(esw->mode_lock) <- Lock A
In subsequent patch, mlx5_core driver uses its internal lock during
get() and set() eswitch callbacks.
Other drivers have been inspected which returns either constant during
get operations or reads the value from already allocated structure.
Hence it is safe to remove the lock in get( ) callback and let vendor
driver handle it.
Parav Pandit [Mon, 9 Mar 2020 03:19:51 +0000 (22:19 -0500)]
net/mlx5: Simplify mlx5_register_device to return void
mlx5_register_device() doesn't check for any error and always returns 0.
Simplify mlx5_register_device() to return void and its caller, remove
dead code related to it.
Eli Cohen [Wed, 4 Mar 2020 08:32:56 +0000 (10:32 +0200)]
net/mlx5: Avoid group version scan when not necessary
Group version is used when modifying a rule is allowed
(FLOW_ACT_NO_APPEND is clear) to detect a case where the rule was found
but while the groups where unlocked a new FTE was added. In this case,
the added FTE could be one with identical match value so we need to
attempt again with group lock held.
Change the code so version is retrieved only when FLOW_ACT_NO_APPEND is
cleared. As result, later compare can also be avoided if FLOW_ACT_NO_APPEND
is cleared.
Also improve comments text.
Signed-off-by: Eli Cohen <eli@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Wed, 4 Mar 2020 08:32:56 +0000 (10:32 +0200)]
net/mlx5: Fix group version management
When adding a rule to a flow group we need increment the version of the
group. Current code fails to do that and as a result, when trying to add
a rule, we will fail to discover a case where an FTE with the same match
value was added while we scanned the groups of the same match criteria,
thus we may try to add an FTE that was already added.
Signed-off-by: Eli Cohen <eli@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Wed, 26 Feb 2020 13:03:16 +0000 (15:03 +0200)]
net/mlx5: Simplify matching group searches
Instead of using two different structs for searching groups with the
same match, use a single struct and thus simplify the code, make it more
readable and smaller size which means less code cache misses.
text data bss dec hex
before: 35524 2744 0 38268 957c
after: 35038 2744 0 37782 9396
When testing add 70000 rules, delete all the rules, and repeat three
times taking the average, we get (time in seconds):
Before the change: insert 16.80, delete 11.02
After the change: insert 16.55, delete 10.95
Signed-off-by: Eli Cohen <eli@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Roi Dayan [Thu, 19 Mar 2020 15:48:18 +0000 (17:48 +0200)]
net/mlx5: E-Switch, free flow_group_in after creating the restore table
We allocate a temporary memory but forget to free it.
Fixes: d8802af9ffdc ("net/mlx5: E-Switch, Get reg_c0 value on CQE") Signed-off-by: Roi Dayan <roid@mellanox.com> Reviewed-by: Paul Blakey <paulb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Paul Blakey [Wed, 18 Mar 2020 09:43:06 +0000 (11:43 +0200)]
net/mlx5: E-Switch, Enable chains only if regs loopback is enabled
Register c0 loopback is needed to fully support chains and prios.
Enable chains and prio only if loopback (of reg c1 which came together
with c0), is enabled. To be able to check that, move enabling of loopback
before eswitch chains init.
Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Paul Blakey [Wed, 18 Mar 2020 08:55:12 +0000 (10:55 +0200)]
net/mlx5: E-Switch, Enable restore table only if reg_c1 is supported
Reg c0/c1 matching, rewrite of regs c0/c1, and copy header of regs c1,B
is needed for the restore table to function, might not be supported by
firmware, and creation of the restore table or the copy header will
fail.
Check reg_c1 loopback support, as firmware which supports this,
should have all of the above.
Fixes: d8802af9ffdc ("net/mlx5: E-Switch, Get reg_c0 value on CQE") Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Dan Carpenter [Fri, 20 Mar 2020 13:23:05 +0000 (16:23 +0300)]
net/mlx5e: Fix actions_match_supported() return
The actions_match_supported() function returns a bool, true for success
and false for failure. This error path is returning a negative which
is cast to true but it should return false.
Fixes: 523aa4ec2a2d ("net/mlx5e: CT: Introduce connection tracking") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
1) Fix deadlock in bpf_send_signal() from Yonghong Song.
2) Fix off by one in kTLS offload of mlx5, from Tariq Toukan.
3) Add missing locking in iwlwifi mvm code, from Avraham Stern.
4) Fix MSG_WAITALL handling in rxrpc, from David Howells.
5) Need to hold RTNL mutex in tcindex_partial_destroy_work(), from Cong
Wang.
6) Fix producer race condition in AF_PACKET, from Willem de Bruijn.
7) cls_route removes the wrong filter during change operations, from
Cong Wang.
8) Reject unrecognized request flags in ethtool netlink code, from
Michal Kubecek.
9) Need to keep MAC in reset until PHY is up in bcmgenet driver, from
Doug Berger.
10) Don't leak ct zone template in act_ct during replace, from Paul
Blakey.
11) Fix flushing of offloaded netfilter flowtable flows, also from Paul
Blakey.
12) Fix throughput drop during tx backpressure in cxgb4, from Rahul
Lakkireddy.
13) Don't let a non-NULL skb->dev leave the TCP stack, from Eric
Dumazet.
14) TCP_QUEUE_SEQ socket option has to update tp->copied_seq as well,
also from Eric Dumazet.
15) Restrict macsec to ethernet devices, from Willem de Bruijn.
16) Fix reference leak in some ethtool *_SET handlers, from Michal
Kubecek.
17) Fix accidental disabling of MSI for some r8169 chips, from Heiner
Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (138 commits)
net: Fix CONFIG_NET_CLS_ACT=n and CONFIG_NFT_FWD_NETDEV={y, m} build
net: ena: Add PCI shutdown handler to allow safe kexec
selftests/net/forwarding: define libs as TEST_PROGS_EXTENDED
selftests/net: add missing tests to Makefile
r8169: re-enable MSI on RTL8168c
net: phy: mdio-bcm-unimac: Fix clock handling
cxgb4/ptp: pass the sign of offset delta in FW CMD
net: dsa: tag_8021q: replace dsa_8021q_remove_header with __skb_vlan_pop
net: cbs: Fix software cbs to consider packet sending time
net/mlx5e: Do not recover from a non-fatal syndrome
net/mlx5e: Fix ICOSQ recovery flow with Striding RQ
net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset
net/mlx5e: Enhance ICOSQ WQE info fields
net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure
selftests: netfilter: add nfqueue test case
netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
netfilter: nft_fwd_netdev: validate family and chain type
netfilter: nft_set_rbtree: Detect partial overlaps on insertion
netfilter: nft_set_rbtree: Introduce and use nft_rbtree_interval_start()
netfilter: nft_set_pipapo: Separate partial and complete overlap cases on insertion
...
Linus Torvalds [Wed, 25 Mar 2020 20:52:36 +0000 (13:52 -0700)]
Merge tag 'gpio-v5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- One core quirk by myself to fix the .irq_disable() semantics when the
gpiolib core takes over this callback.
- The rest is an elaborate series of four patches fixing Intel laptop
ACPI wakeup quirks.
* tag 'gpio-v5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: acpi: Add quirk to ignore EC wakeups on HP x2 10 CHT + AXP288 model
gpiolib: acpi: Add quirk to ignore EC wakeups on HP x2 10 BYT + AXP288 model
gpiolib: acpi: Rework honor_wakeup option into an ignore_wake option
gpiolib: acpi: Correct comment for HP x2 10 honor_wakeup quirk
gpiolib: Fix irq_disable() semantics
net: Fix CONFIG_NET_CLS_ACT=n and CONFIG_NFT_FWD_NETDEV={y, m} build
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: ed7040a300fa33f4 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress") Reported-by: noreply@ellerman.id.au Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rahul Kundu [Wed, 25 Mar 2020 11:53:09 +0000 (04:53 -0700)]
cxgb4: Add support to catch bits set in INT_CAUSE5
This commit adds support to catch any bits set in SGE_INT_CAUSE5 for Parity Errors.
F_ERR_T_RXCRC flag is used to ignore that particular bit as it is not considered as fatal.
So, we clear out the bit before looking for error.
This patch now read and report separately all three registers(Cause1, Cause2, Cause5).
Also, checks for errors if any.
Signed-off-by: Raju Rangoju <rajur@chelsio.com> Signed-off-by: Rahul Kundu <rahul.kundu@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
please apply the following patch series for qeth to netdev's net-next
tree.
Same series as yesterday, with one minor update to patch 1 as per
your review.
This adds
1) NAPI poll support for the async-Completion Queue (with one qdio layer
patch acked by Heiko),
2) ethtool support for per-queue TX IRQ coalescing,
3) various cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:35:06 +0000 (10:35 +0100)]
s390/qeth: keep track of fixed prio-queue configuration
When a device is configured in prio-queue mode to pin all traffic onto
a specific HW queue, treat this as a distinct variant of prio-queueing
instead of QETH_NO_PRIO_QUEUEING.
This corrects an error message from qeth_osa_set_output_queues() for
devices configured in such a mode.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:35:04 +0000 (10:35 +0100)]
s390/qeth: add TX IRQ coalescing support for IQD devices
Since IQD devices complete (most of) their transmissions synchronously,
they don't offer TX completion IRQs and have no HW coalescing controls.
But we can fake the easy parts in SW, and give the user some control wrt
to how often the TX NAPI code should be triggered to process the TX
completions.
Having per-queue controls can in particular help the dedicated mcast
queue, as it likely benefits from different fine-tuning than what the
ucast queues need.
CC: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:35:03 +0000 (10:35 +0100)]
s390/qeth: collect more TX statistics
Count the number of TX doorbells we issue to the qdio layer.
Also count the number of actual frames in a TX buffer, and then
use this data along with the byte count during TX completion.
We'll make additional use of the frame count in a subsequent patch.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:35:02 +0000 (10:35 +0100)]
s390/qeth: clean up the mac_bits
We're down to a single bit flag for MAC-address related status, reflect
that in the info struct.
Also set up the flag during initialization instead of clearing it during
shutdown - one more little step towards unifying the shutdown code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:35:01 +0000 (10:35 +0100)]
s390/qeth: simplify L3 dev_id logic
The logic that deals with errors from qeth_l3_get_unique_id() is quite
complex: it sets card->unique_id to 0xfffe, additionally flags it as
UNIQUE_ID_NOT_BY_CARD and later takes this flag as cue to not propagate
card->unique_id to dev->dev_id. With dev->dev_id thus holding 0,
addrconf_ifid_eui48() applies its default behaviour.
Get rid of all the special bit masks, and just return the old uid in
case of an error. For the vast majority of cases this will be 0 (and so
we still get the desired default behaviour) - with the rare exception
where qeth_l3_get_unique_id() might have been called earlier but the
initialization then failed at a later point.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:35:00 +0000 (10:35 +0100)]
s390/qdio: extend polling support to multiple queues
When the support for polling drivers was initially added, it only
considered Input Queue 0. But as QDIO interrupts are actually for the
full device and not a single queue, this doesn't really fit for
configurations where multiple Input Queues are used.
Rework the qdio code so that interrupts for a polling driver are not
split up into actions for each queue. Instead deliver the interrupt as
a single event, and let the driver decide which queue needs what action.
When re-enabling the QDIO interrupt via qdio_start_irq(), this means
that the qdio code needs to
(1) put _all_ eligible queues back into a state where they raise IRQs,
(2) and afterwards check _all_ eligible queues for new work to bridge
the race window.
On the qeth side of things (as the only qdio polling driver), we can now
add CQ polling support to the main NAPI poll routine. It doesn't consume
NAPI budget, and to avoid hogging the CPU we yield control after
completing one full queue worth of buffers.
The subsequent qdio_start_irq() will check for any additional work, and
have us re-schedule the NAPI instance accordingly.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:34:59 +0000 (10:34 +0100)]
s390/qeth: remove redundant if-clause in RX poll code
Whenever all completed RX buffers have been processed
(ie. rx->b_count == 0), we call down to the HW layer to scan for
additional buffers. If no further buffers are available, the code
breaks out of the while-loop.
So we never reach the 'process an RX buffer' step with rx->b_count == 0,
eliminate that check and one level of indentation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:34:58 +0000 (10:34 +0100)]
s390/qeth: split out RX poll code
The main NAPI poll routine should eventually handle more types of work,
beyond just the RX ring.
Split off the RX poll logic into a separate function, and simplify the
nested while-loop.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 25 Mar 2020 09:34:57 +0000 (10:34 +0100)]
s390/qeth: simplify RX buffer tracking
Since RX buffers may contain multiple packets, qeth's NAPI poll code can
exhaust its budget in the middle of an RX buffer. Thus we keep track of
our current position within the active RX buffer, so we can resume
processing here in the next NAPI poll period.
Clean up that code by tracking the index of the active buffer element,
instead of a pointer to it.
Also simplify the code that advances to the next RX buffer when the
current buffer has been fully processed.
v2: - remove QDIO_ELEMENT_NO() macro (davem)
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ena: Add PCI shutdown handler to allow safe kexec
Currently ENA only provides the PCI remove() handler, used during rmmod
for example. This is not called on shutdown/kexec path; we are potentially
creating a failure scenario on kexec:
(a) Kexec is triggered, no shutdown() / remove() handler is called for ENA;
instead pci_device_shutdown() clears the master bit of the PCI device,
stopping all DMA transactions;
(b) Kexec reboot happens and the device gets enabled again, likely having
its FW with that DMA transaction buffered; then it may trigger the (now
invalid) memory operation in the new kernel, corrupting kernel memory area.
This patch aims to prevent this, by implementing a shutdown() handler
quite similar to the remove() one - the difference being the handling
of the netdev, which is unregistered on remove(), but following the
convention observed in other drivers, it's only detached on shutdown().
This prevents an odd issue in AWS Nitro instances, in which after the 2nd
kexec the next one will fail with an initrd corruption, caused by a wild
DMA write to invalid kernel memory. The lspci output for the adapter
present in my instance is:
Suggested-by: Gavin Shan <gshan@redhat.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@canonical.com> Acked-by: Sameeh Jubran <sameehj@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Wed, 25 Mar 2020 08:41:01 +0000 (16:41 +0800)]
selftests/net/forwarding: define libs as TEST_PROGS_EXTENDED
The lib files should not be defined as TEST_PROGS, or we will run them
in run_kselftest.sh.
Also remove ethtool_lib.sh exec permission.
Fixes: 1ab04a373f2a ("selftests/net/forwarding: add Makefile to install tests") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 25 Mar 2020 02:23:21 +0000 (19:23 -0700)]
net: use indirect call wrappers for skb_copy_datagram_iter()
TCP recvmsg() calls skb_copy_datagram_iter(), which
calls an indirect function (cb pointing to simple_copy_to_iter())
for every MSS (fragment) present in the skb.
CONFIG_RETPOLINE=y forces a very expensive operation
that we can avoid thanks to indirect call wrappers.
This patch gives a 13% increase of performance on
a single flow, if the bottleneck is the thread reading
the TCP socket.
Fixes: 8dc3f0dbe4ca ("datagram: consolidate datagram copy to iter helpers") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 25 Mar 2020 01:17:50 +0000 (09:17 +0800)]
cxgb4: remove set but not used variable 'tab'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c: In function cxgb4_get_free_ftid:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_filter.c:547:23:
warning: variable tab set but not used [-Wunused-but-set-variable]
commit a910a42aee0e ("cxgb4: rework TC filter rule insertion across regions")
involved this, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Damien Le Moal [Fri, 20 Mar 2020 12:36:54 +0000 (21:36 +0900)]
zonfs: Fix handling of read-only zones
The write pointer of zones in the read-only consition is defined as
invalid by the SCSI ZBC and ATA ZAC specifications. It is thus not
possible to determine the correct size of a read-only zone file on
mount. Fix this by handling read-only zones in the same manner as
offline zones by disabling all accesses to the zone (read and write)
and initializing the inode size of the read-only zone to 0).
For zones found to be in the read-only condition at runtime, only
disable write access to the zone and keep the size of the zone file to
its last updated value to allow the user to recover previously written
data.
Also fix zonefs documentation file to reflect this change.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
The following patchset contains Netfilter fixes for net:
1) A new selftest for nf_queue, from Florian Westphal. This test
covers two recent fixes: 53c10d6f9e43 ("tcp: also NULL skb->dev
when copy was needed") and 8cc31357d03b ("tcp: ensure skb->dev is
NULL before leaving TCP stack").
2) The fwd action breaks with ifb. For safety in next extensions,
make sure the fwd action only runs from ingress until it is extended
to be used from a different hook.
3) The pipapo set type now reports EEXIST in case of subrange overlaps.
Update the rbtree set to validate range overlaps, so far this
validation is only done only from userspace. From Stefano Brivio.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
From Aya, Fixes to the RX error recovery flows
From Leon, Fix IB capability mask
Please pull and let me know if there is any problem.
For -stable v5.5
('net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure')
For -stable v5.4
('net/mlx5e: Fix ICOSQ recovery flow with Striding RQ')
('net/mlx5e: Do not recover from a non-fatal syndrome')
('net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset')
('net/mlx5e: Enhance ICOSQ WQE info fields')
The above patch ('net/mlx5e: Enhance ICOSQ WQE info fields')
will fail to apply cleanly on v5.4 due to a trivial contextual conflict,
but it is an important fix, do I need to do something about it or just
assume Greg will know how to handle this ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 24 Mar 2020 19:58:29 +0000 (20:58 +0100)]
r8169: re-enable MSI on RTL8168c
The original change fixed an issue on RTL8168b by mimicking the vendor
driver behavior to disable MSI on chip versions before RTL8168d.
This however now caused an issue on a system with RTL8168c, see [0].
Therefore leave MSI disabled on RTL8168b, but re-enable it on RTL8168c.
Fixes: 759dd3c2f322 ("r8169: don't use MSI before RTL8168d") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 24 Mar 2020 17:30:16 +0000 (10:30 -0700)]
devlink: expand the devlink-info documentation
We are having multiple review cycles with all vendors trying
to implement devlink-info. Let's expand the documentation with
more information about what's implemented and motivation behind
this interface in an attempt to make the implementations easier.
Describe what each info section is supposed to contain, and make
some references to other HW interfaces (PCI caps).
Document how firmware management is expected to look, to make
it clear how devlink-info and devlink-flash work in concert.
Name some future work.
v2: - improve wording
v3: - improve wording
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Przywara [Tue, 24 Mar 2020 16:10:10 +0000 (16:10 +0000)]
net: phy: mdio-bcm-unimac: Fix clock handling
The DT binding for this PHY describes an *optional* clock property.
Due to a bug in the error handling logic, we are actually ignoring this
clock *all* of the time so far.
Fix this by using devm_clk_get_optional() to handle this clock properly.
Fixes: e0db9e21471bc ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider") Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 24 Mar 2020 14:13:58 +0000 (16:13 +0200)]
net: phy: mscc: consolidate a common RGMII delay implementation
It looks like the VSC8584 PHY driver is rolling its own RGMII delay
configuration code, despite the fact that the logic is mostly the same.
In fact only the register layout and position for the RGMII controls has
changed. So we need to adapt and parameterize the PHY-dependent bit
fields when calling the new generic function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log