Hector Martin [Thu, 30 Jun 2022 07:51:35 +0000 (09:51 +0200)]
ASoC: tas2764: Fix amp gain register offset & default
The register default is 0x28 per the datasheet, and the amp gain field
is supposed to be shifted left by one. With the wrong default, the ALSA
controls lie about the power-up state. With the wrong shift, we get only
half the gain we expect.
Signed-off-by: Hector Martin <marcan@marcan.st> Fixes: ff5fd908f544 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Link: https://lore.kernel.org/r/20220630075135.2221-4-povik+lin@cutebit.org Signed-off-by: Mark Brown <broonie@kernel.org>
Hector Martin [Thu, 30 Jun 2022 07:51:34 +0000 (09:51 +0200)]
ASoC: tas2764: Correct playback volume range
DVC value 0xc8 is -100dB and 0xc9 is mute; this needs to map to
-100.5dB as far as the dB scale is concerned. Fix that and enable
the mute flag, so alsamixer correctly shows the control as
<0 dB .. -100 dB, mute>.
Signed-off-by: Hector Martin <marcan@marcan.st> Fixes: ff5fd908f544 ("ASoC: tas2764: Add the driver for the TAS2764") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Link: https://lore.kernel.org/r/20220630075135.2221-3-povik+lin@cutebit.org Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Povišer [Thu, 30 Jun 2022 07:51:33 +0000 (09:51 +0200)]
ASoC: tas2764: Fix and extend FSYNC polarity handling
Fix setting of FSYNC polarity in case of LEFT_J and DSP_A/B formats.
Do NOT set the SCFG field as was previously done, because that is not
correct and is also in conflict with the "ASI1 Source" control which
sets the same SCFG field!
Martin Povišer [Thu, 30 Jun 2022 07:51:32 +0000 (09:51 +0200)]
ASoC: tas2764: Add post reset delays
Make sure there is at least 1 ms delay from reset to first command as
is specified in the datasheet. This is a fix similar to commit 0dea35f7773b ("ASoC: tas2770: Insert post reset delay").
Charles Keepax [Tue, 28 Jun 2022 15:34:09 +0000 (16:34 +0100)]
ASoC: arizona: Update arizona_aif_cfg_changed to use RX_BCLK_RATE
Currently the function arizona_aif_cfg_changed uses the TX_BCLK_RATE,
however this register is not used on wm8998. This was not noticed as
previously snd_soc_component_read did not print an error message.
However, now the log gets filled with error messages, further more the
test for if the LRCLK changed will return spurious results.
Update the code to use the RX_BCLK_RATE register, the LRCLK parameters
are written to both registers and the RX_BCLK_RATE register is used
across all Arizona devices.
Charles Keepax [Tue, 28 Jun 2022 15:34:08 +0000 (16:34 +0100)]
ASoC: cs47l92: Fix event generation for OUT1 demux
cs47l92_put_demux returns the value of snd_soc_dapm_mux_update_power,
which returns a 1 if a path was found for the kcontrol. This is
obviously different to the expected return a 1 if the control
was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Charles Keepax [Tue, 28 Jun 2022 15:34:07 +0000 (16:34 +0100)]
ASoC: wm8998: Fix event generation for input mux
wm8998_inmux_put returns the value of snd_soc_dapm_mux_update_power,
which returns a 1 if a path was found for the kcontrol. This is
obviously different to the expected return a 1 if the control
was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Charles Keepax [Tue, 28 Jun 2022 15:34:06 +0000 (16:34 +0100)]
ASoC: wm5102: Fix event generation for output compensation
The output compensation controls always returns zero regardless of if
the control value was updated. This results in missing notifications
to user-space of the control change. Update the handling to return 1
when the value is changed.
Yassine Oudjana [Wed, 22 Jun 2022 06:17:45 +0000 (10:17 +0400)]
ASoC: wcd9335: Use int array instead of bitmask for TX mixers
Currently slim_tx_mixer_get reports all TX mixers as enabled when
at least one is, due to it reading the entire tx_port_value bitmask
without testing the specific bit corresponding to a TX port.
Furthermore, using the same bitmask for all capture DAIs makes
setting one mixer affect them all. To prevent this, and since
the SLIM TX muxes effectively only connect to one of the mixers
at a time, turn tx_port_value into an int array storing the DAI
index each of the ports is connected to.
Sascha Hauer [Fri, 24 Jun 2022 10:57:16 +0000 (12:57 +0200)]
ASoC: tlv320adcx140: Fix tx_mask check
The tx_mask check doesn't reflect what the driver and the chip support.
The check currently checks for exactly two slots being enabled. The
tlv320adcx140 supports anything between one and eight channels, so relax
the check accordingly.
The tlv320adcx140 supports arbitrary tx_mask settings, but the driver
currently only supports adjacent slots beginning with the first slot,
so extend the check to check that the first slot is being used and that
there are no holes in the tx_mask.
Leave a comment to make it's the driver that limits the tx_mask
settings, not the chip itself.
While at it remove the set-but-unused struct adcx140p_priv::tdm_delay
field.
David Owens [Mon, 20 Jun 2022 18:37:43 +0000 (13:37 -0500)]
ASoC: ti: omap-mcbsp: duplicate sysfs error
Convert to managed versions of sysfs and clk allocation to simplify
unbinding and error handling in probe. Managed sysfs node
creation specifically addresses the following error seen the second time
probe is attempted after sdma_pcm_platform_register() previously requsted
probe deferral:
Put the SGTL5000 in a silent/safe state on shutdown/remove, this is
required since the SGTL5000 produces a constant noise on its output
after it is configured and its clock is removed. Without this change
this is happening every time the module is unbound/removed or from
reboot till the clock is enabled again.
The issue was experienced on both a Toradex Colibri/Apalis iMX6, but can
be easily reproduced everywhere just playing something on the codec and
after that removing/unbinding the driver.
Charles Keepax [Thu, 23 Jun 2022 10:51:19 +0000 (11:51 +0100)]
ASoC: madera: Fix event generation for rate controls
madera_adsp_rate_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the
value is changed.
Charles Keepax [Thu, 23 Jun 2022 10:51:18 +0000 (11:51 +0100)]
ASoC: madera: Fix event generation for OUT1 demux
madera_out1_demux_put returns the value of
snd_soc_dapm_mux_update_power, which returns a 1 if a path was found for
the kcontrol. This is obviously different to the expected return a 1 if
the control was updated value. This results in spurious notifications to
user-space. Update the handling to only return a 1 when the value is
changed.
Charles Keepax [Thu, 23 Jun 2022 10:51:17 +0000 (11:51 +0100)]
ASoC: cs47l15: Fix event generation for low power mux control
cs47l15_in1_adc_put always returns zero regardless of if the control
value was updated. This results in missing notifications to user-space
of the control change. Update the handling to return 1 when the value is
changed.
Charles Keepax [Thu, 23 Jun 2022 10:51:16 +0000 (11:51 +0100)]
ASoC: cs35l41: Add ASP TX3/4 source to register patch
The mixer controls for ASP TX3/4 are set to values that are not included
in their enumeration control. This will cause spurious event
notifications when the controls are first changed, as the register value
changes whilst the actual visible enumeration value does not. Use the
register patch to set them to a known value, zero, which equates to zero
fill, thereby avoiding the spurious notifications.
Charles Keepax [Thu, 23 Jun 2022 10:51:15 +0000 (11:51 +0100)]
ASoC: dapm: Initialise kcontrol data for mux/demux controls
DAPM keeps a copy of the current value of mux/demux controls,
however this value is only initialised in the case of autodisable
controls. This leads to false notification events when first
modifying a DAPM kcontrol that has a non-zero default.
Autodisable controls are left as they are, since they already
initialise the value, and there would be more work required to
support autodisable muxes where the first option isn't disabled
and/or that isn't the default.
Technically this issue could affect mixer/switch elements as well,
although not on any of the devices I am currently running. There
is also a little more work to do to address the issue there due to
that side supporting stereo controls, so that has not been tackled
in this patch.
Shuming Fan [Tue, 21 Jun 2022 09:07:19 +0000 (17:07 +0800)]
ASoC: rt711-sdca: fix kernel NULL pointer dereference when IO error
The initial settings will be written before the codec probe function.
But, the rt711->component doesn't be assigned yet.
If IO error happened during initial settings operations, it will cause the kernel panic.
This patch changed component->dev to slave->dev to fix this issue.
Judy Hsiao [Wed, 15 Jun 2022 04:56:43 +0000 (04:56 +0000)]
ASoC: rockchip: i2s: switch BCLK to GPIO
We discoverd that the state of BCLK on, LRCLK off and SD_MODE on
may cause the speaker melting issue. Removing LRCLK while BCLK
is present can cause unexpected output behavior including a large
DC output voltage as described in the Max98357a datasheet.
In order to:
1. prevent BCLK from turning on by other component.
2. keep BCLK and LRCLK being present at the same time
This patch switches BCLK to GPIO func before LRCLK output, and
configures BCLK func back during LRCLK is output.
Without this fix, BCLK is turned on 11 ms earlier than LRCK by the
da7219.
With this fix, BCLK is turned on only 0.4 ms earlier than LRCK by
the rockchip codec.
ASoC: SOF: Intel: disable IMR boot when resuming from ACPI S4 and S5 states
The IMR was assumed to be preserved when suspending to S4 and S5
states, but community reports invalidate that assumption, the hardware
seems to be powered off and the IMR memory content cleared.
Make sure regular boot with firmware download is used for S4 and S5.
ASoC: SOF: pm: add definitions for S4 and S5 states
We currently don't have a means to differentiate between S3, S4 and
S5. Add definitions so that we have select different code paths
depending on the target state in follow-up patches.
Peter Ujfalusi [Thu, 16 Jun 2022 20:19:53 +0000 (15:19 -0500)]
ASoC: SOF: Intel: hda: Fix compressed stream position tracking
Commit f27850a417a9 ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information")
modified the PCM path only, but left the compressed data patch using an
obsolete option.
Move the functionality in a helper that can be called for both PCM and
compressed data.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Fixes: f27850a417a9 ("ASoC: SOF: Intel: hda: add quirks for HDAudio DMA position information") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20220616201953.130876-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede [Sun, 12 Jun 2022 15:56:52 +0000 (17:56 +0200)]
ASoC: Intel: bytcr_wm5102: Fix GPIO related probe-ordering problem
The "wlf,spkvdd-ena" GPIO needed by the bytcr_wm5102 driver
is made available through a gpio-lookup table.
This gpio-lookup table is registered by drivers/mfd/arizona-spi.c, which
may get probed after the bytcr_wm5102 driver.
If the gpio-lookup table has not registered yet then the gpiod_get()
will return -ENOENT. Treat -ENOENT as -EPROBE_DEFER to still keep
things working in this case.
Keyon Jie was a key contributor to the Intel ASoC and SOF Intel
drivers, but he's moved on to a different role within Intel. We wish
him all the best in his new endeavors.
Bard Liao, Kai Vehmanen, Ranjani Sridharan and Peter Ujfalusi have
been involved in the Intel multi-maintainer team, it's time to update
the MAINTAINERS entry to reflect their contributions and clarify their
role.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20220610214313.42903-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 3 Jun 2022 12:25:26 +0000 (14:25 +0200)]
ASoC: wcd938x: Fix event generation for some controls
Currently wcd938x_*_put() unconditionally report that the value of the
control changed, resulting in spurious events being generated. Return 0 in
that case instead as we should. There is still an issue in the compander
control which is a bit more complex.
Mark Brown [Fri, 3 Jun 2022 12:46:09 +0000 (14:46 +0200)]
ASoC: wcd9335: Fix spurious event generation
The slimbus mux put operation unconditionally reports a change in value
which means that spurious events are generated. Fix this by exiting early
in that case.
Yassine Oudjana [Mon, 6 Jun 2022 15:22:26 +0000 (19:22 +0400)]
ASoC: wcd9335: Remove RX channel from old list before adding it to a new one
Currently in slim_rx_mux_put, an RX channel gets added to a new list
even if it is already in one. This can mess up links and make either
it, the new list head, or both, get linked to the wrong entries.
This can cause an entry to link to itself which in turn ends up
making list_for_each_entry in other functions loop infinitely.
To avoid issues, always remove the RX channel from any list it's in
before adding it to a new list.
Commit a299af034fc6 ("ASoC: remove codec hw_write/control_data") removed
use of hw_write_t in struct snd_soc_codec, but it left type definition.
Fully clean it up.
Peter Ujfalusi [Fri, 10 Jun 2022 08:47:35 +0000 (11:47 +0300)]
ASoC: SOF: ipc3-topology: Move and correct size checks in sof_ipc3_control_load_bytes()
Move the size checks prior to allocating memory as these checks do not need
the data to be allocated and in case of an error we would not need to free
the allocation.
The max size must not be less than the size of
struct sof_ipc_ctrl_data + struct sof_abi_hdr as the ABI header needs to
be present under all circumstances.
The check was incorrectly used or between the two size checks.
Fixes: 806f4f0b3d81 ("ASoC: SOF: topology: Make control parsing IPC agnostic") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://lore.kernel.org/r/20220610084735.19397-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Thu, 9 Jun 2022 08:59:49 +0000 (11:59 +0300)]
ASoC: SOF: Intel: hda-loader: Clarify the cl_dsp_init() flow
Update the comment for the cl_dsp_init() to clarify what is done by the
function and use the chip->init_core_mask instead of BIT(0) when
unstalling/running the init core.
Peter Ujfalusi [Thu, 9 Jun 2022 08:59:48 +0000 (11:59 +0300)]
ASoC: SOF: Intel: hda-loader: Make sure that the fw load sequence is followed
The hda_dsp_enable_core() is powering up _and_ unstall the core in one
call while the first step of the firmware loading must not unstall the
core.
The core can be unstalled only after the set cpb_cfp and the configuration
of the IPC register for the ROM_CONTROL message.
The hda_dsp_core_power_up() needs to be exposed so that it can be used in
hda-loader.c to correct the boot flow.
The first step must not unstall the core, it should only power up the
core(s).
Add sanity check for the core_mask while exposing it to be safe.
ASoC: ak4613: cares Simple-Audio-Card case for TDM
Renesas is the only user of ak4613 on upstream for now, and
commit 1a0c74e5e05745 ("ASoC: ak4613: add TDM256 support")
added TDM256 support. Renesas tested part of it, because of
board connection.
It was assuming ak4613 is probed via Audio-Graph-Card, but it
might be probed via Simple-Audio-Card either.
It will indicates WARNING in such case. This patch fixup it.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/87h74v29f7.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: codecs: rt700/rt711/rt711-sdca: resume bus/codec in .set_jack_detect
The .set_jack_detect() codec component callback is invoked during card
registration, which happens when the machine driver is probed.
The issue is that this callback can race with the bus suspend/resume,
and IO timeouts can happen. This can be reproduced very easily if the
machine driver is 'blacklisted' and manually probed after the bus
suspends. The bus and codec need to be re-initialized using pm_runtime
helpers.
Previous contributions tried to make sure accesses to the bus during
the .set_jack_detect() component callback only happen when the bus is
active. This was done by changing the regcache status on a component
remove. This is however a layering violation, the regcache status
should only be modified on device probe, suspend and resume. The
component probe/remove should not modify how the device regcache is
handled. This solution also didn't handle all the possible race
conditions, and the RT700 headset codec was not handled.
This patch tries to resume the codec device before handling the jack
initializations. In case the codec has not yet been initialized,
pm_runtime may not be enabled yet, so we don't squelch the -EACCES
error code and only stop the jack information. When the codec reports
as attached, the jack initialization will proceed as usual.
ASoC: codecs: rt700/rt711/rt711-sdca: initialize workqueues in probe
The workqueues are initialized in the io_init functions, which isn't
quite right. In some tests, this leads to warnings throw from
__queue_delayed_work()
Realtek headset codec drivers typically check if the card is
instantiated before proceeding with the jack detection.
The rt700, rt711 and rt711-sdca are however missing a check on the
card pointer, which can lead to NULL dereferences encountered in
driver bind/unbind tests.
ASoC: Intel: sof_sdw: handle errors on card registration
If the card registration fails, typically because of deferred probes,
the device properties added for headset codecs are not removed, which
leads to kernel oopses in driver bind/unbind tests.
We already clean-up the device properties when the card is removed,
this code can be moved as a helper and called upon card registration
errors.
A quick check in the code shows that the 'calibrate_mutex' used by
this driver are not initialized at probe time. Moving the
initialization to the probe removes the issue.
Mark Brown [Fri, 3 Jun 2022 11:50:03 +0000 (13:50 +0200)]
ASoC: wm_adsp: Fix event generation for wm_adsp_fw_put()
Currently wm_adsp_fw_put() returns 0 rather than 1 when updating the value
of the control, meaning that no event is generated to userspace. Fix this
by setting the default return value to 1, the code already exits early with
a return value of 0 if the value is unchanged.
Mark Brown [Fri, 3 Jun 2022 12:39:37 +0000 (14:39 +0200)]
ASoC: es8328: Fix event generation for deemphasis control
Currently the put() method for the deemphasis control returns 0 when a new
value is written to the control even if the value changed, meaning events
are not generated. Fix this, skip the work of updating the value when it is
unchanged and then return 1 after having done so.
Dan Carpenter [Thu, 2 Jun 2022 09:09:35 +0000 (12:09 +0300)]
ASoC: SOF: ipc-msg-injector: Fix reversed if statement
This if statement is reversed. In fact, the condition can just be
deleted because writing zero bytes is a no-op.
Fixes: 73bffe328996 ("ASoC: SOF: ipc-msg-injector: Add support for IPC4 messages") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/Yph+T3PpGCdPsEDj@kili Signed-off-by: Mark Brown <broonie@kernel.org>
This code is supposed to propagate errors from simple_write_to_buffer()
or return -EFAULT if "size != count". However "size" needs to be signed
for the code to work correctly and the case where "size == 0" is not
handled correctly.
Fixes: 73bffe328996 ("ASoC: SOF: ipc-msg-injector: Add support for IPC4 messages") Fixes: a66e6ff7622f ("ASoC: SOF: debug: Add support for IPC message injection") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/Yph+Cd+JrfOH0i7z@kili Signed-off-by: Mark Brown <broonie@kernel.org>
Cleanup path for sof_prepare_widgets_in_path() should check if unprepare
callback exists before calling it, instead it checks if it does not
exist. Fix the check.
Linus Torvalds [Mon, 6 Jun 2022 00:14:03 +0000 (17:14 -0700)]
Merge tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull file descriptor fix from Al Viro:
"Fix for breakage in #work.fd this window"
* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the breakage in close_fd_get_file() calling conventions change
Linus Torvalds [Sun, 5 Jun 2022 18:51:48 +0000 (11:51 -0700)]
bluetooth: don't use bitmaps for random flag accesses
The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.
It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32. It shoudln't have been a bitmap in the first
place. The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.
The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.
So just use a regular integer.
In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).
That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit a1a19b185fa0 ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.
Al Viro [Sun, 5 Jun 2022 18:01:42 +0000 (14:01 -0400)]
fix the breakage in close_fd_get_file() calling conventions change
It used to grab an extra reference to struct file rather than
just transferring to caller the one it had removed from descriptor
table. New variant doesn't, and callers need to be adjusted.
Reported-and-tested-by: syzbot+47dd250f527cb7bebf24@syzkaller.appspotmail.com Fixes: 8d392c99b321 ("Unify the primitives for file descriptor closing") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sun, 5 Jun 2022 18:00:43 +0000 (11:00 -0700)]
Merge tag 'x86-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 SGX fix from Thomas Gleixner:
"A single fix for x86/SGX to prevent that memory which is allocated for
an SGX enclave is accounted to the wrong memory control group"
* tag 'x86-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sgx: Set active memcg prior to shmem allocation
Linus Torvalds [Sun, 5 Jun 2022 17:55:23 +0000 (10:55 -0700)]
Merge tag 'x86-microcode-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 microcode updates from Thomas Gleixner:
- Disable late microcode loading by default. Unless the HW people get
their act together and provide a required minimum version in the
microcode header for making a halfways informed decision its just
lottery and broken.
- Warn and taint the kernel when microcode is loaded late
- Remove the old unused microcode loader interface
- Remove a redundant perf callback from the microcode loader
* tag 'x86-microcode-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Remove unnecessary perf callback
x86/microcode: Taint and warn on late loading
x86/microcode: Default-disable late loading
x86/microcode: Rip out the OLD_INTERFACE
Linus Torvalds [Sun, 5 Jun 2022 17:53:41 +0000 (10:53 -0700)]
Merge tag 'x86-cleanups-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 cleanups from Thomas Gleixner:
"A set of small x86 cleanups:
- Remove unused headers in the IDT code
- Kconfig indendation and comment fixes
- Fix all 'the the' typos in one go instead of waiting for bots to
fix one at a time"
* tag 'x86-cleanups-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix all occurences of the "the the" typo
x86/idt: Remove unused headers
x86/Kconfig: Fix indentation of arch/x86/Kconfig.debug
x86/Kconfig: Fix indentation and add endif comments to arch/x86/Kconfig
Linus Torvalds [Sun, 5 Jun 2022 17:47:06 +0000 (10:47 -0700)]
Merge tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clockevent/clocksource updates from Thomas Gleixner:
- Device tree bindings for MT8186
- Tell the kernel that the RISC-V SBI timer stops in deeper power
states
- Make device tree parsing in sp804 more robust
- Dead code removal and tiny fixes here and there
- Add the missing SPDX identifiers
* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
clocksource/drivers/timer-sun5i: Convert to SPDX identifier
clocksource/drivers/timer-sun4i: Convert to SPDX identifier
clocksource/drivers/pistachio: Convert to SPDX identifier
clocksource/drivers/orion: Convert to SPDX identifier
clocksource/drivers/lpc32xx: Convert to SPDX identifier
clocksource/drivers/digicolor: Convert to SPDX identifier
clocksource/drivers/armada-370-xp: Convert to SPDX identifier
clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
clocksource/drivers/jcore: Convert to SPDX identifier
clocksource/drivers/bcm_kona: Convert to SPDX identifier
clocksource/drivers/sp804: Avoid error on multiple instances
clocksource/drivers/riscv: Events are stopped during CPU suspend
clocksource/drivers/ixp4xx: Drop boardfile probe path
dt-bindings: timer: Add compatible for Mediatek MT8186
Linus Torvalds [Sun, 5 Jun 2022 17:40:31 +0000 (10:40 -0700)]
Merge tag 'perf-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
- Make the ICL event constraints match reality
- Remove a unused local variable
* tag 'perf-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove unused local variable
perf/x86/intel: Fix event constraints for ICL
Linus Torvalds [Sun, 5 Jun 2022 16:45:27 +0000 (09:45 -0700)]
Merge tag 'objtool-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Thomas Gleixner:
- Handle __ubsan_handle_builtin_unreachable() correctly and treat it as
noreturn
- Allow architectures to select uaccess validation
- Use the non-instrumented bit test for test_cpu_has() to prevent
escape from non-instrumentable regions
- Use arch_ prefixed atomics for JUMP_LABEL=n builds to prevent escape
from non-instrumentable regions
- Mark a few tiny inline as __always_inline to prevent GCC from
bringing them out of line and instrumenting them
- Mark the empty stub context_tracking_enabled() as always inline as
GCC brings them out of line and instruments the empty shell
- Annotate ex_handler_msr_mce() as dead end
* tag 'objtool-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/extable: Annotate ex_handler_msr_mce() as a dead end
context_tracking: Always inline empty stubs
x86: Always inline on_thread_stack() and current_top_of_stack()
jump_label,noinstr: Avoid instrumentation for JUMP_LABEL=n builds
x86/cpu: Elide KCSAN for cpu_has() and friends
objtool: Mark __ubsan_handle_builtin_unreachable() as noreturn
objtool: Add CONFIG_HAVE_UACCESS_VALIDATION
Linus Torvalds [Sun, 5 Jun 2022 16:12:28 +0000 (09:12 -0700)]
Merge tag 'hte/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux
Pull hardware timestamping subsystem from Thierry Reding:
"This contains the new HTE (hardware timestamping engine) subsystem
that has been in the works for a couple of months now.
The infrastructure provided allows for drivers to register as hardware
timestamp providers, while consumers will be able to request events
that they are interested in (such as GPIOs and IRQs) to be timestamped
by the hardware providers.
Note that this currently supports only one provider, but there seems
to be enough interest in this functionality and we expect to see more
drivers added once this is merged"
[ Linus Walleij mentions the Intel PMC in the Elkhart and Tiger Lake
platforms as another future timestamp provider ]
* tag 'hte/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: timestamp: Correct id path
dt-bindings: Renamed hte directory to timestamp
hte: Uninitialized variable in hte_ts_get()
hte: Fix off by one in hte_push_ts_ns()
hte: Fix possible use-after-free in tegra_hte_test_remove()
hte: Remove unused including <linux/version.h>
MAINTAINERS: Add HTE Subsystem
hte: Add Tegra HTE test driver
tools: gpio: Add new hardware clock type
gpiolib: cdev: Add hardware timestamp clock type
gpio: tegra186: Add HTE support
gpiolib: Add HTE support
dt-bindings: Add HTE bindings
hte: Add Tegra194 HTE kernel provider
drivers: Add hardware timestamp engine (HTE) subsystem
Documentation: Add HTE subsystem guide
Linus Torvalds [Sun, 5 Jun 2022 16:06:03 +0000 (09:06 -0700)]
Merge tag 'kbuild-v5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- Fix build regressions for parisc, csky, nios2, openrisc
- Simplify module builds for CONFIG_LTO_CLANG and CONFIG_X86_KERNEL_IBT
- Remove arch/parisc/nm, which was presumably a workaround for old
tools
- Check the odd combination of EXPORT_SYMBOL and 'static' precisely
- Make external module builds robust against "too long argument error"
- Support j, k keys for moving the cursor in nconfig
* tag 'kbuild-v5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
kbuild: Allow to select bash in a modified environment
scripts: kconfig: nconf: make nconfig accept jk keybindings
modpost: use fnmatch() to simplify match()
modpost: simplify mod->name allocation
kbuild: factor out the common objtool arguments
kbuild: move vmlinux.o link to scripts/Makefile.vmlinux_o
kbuild: clean .tmp_* pattern by make clean
kbuild: remove redundant cleanups in scripts/link-vmlinux.sh
kbuild: rebuild multi-object modules when objtool is updated
kbuild: add cmd_and_savecmd macro
kbuild: make *.mod rule robust against too long argument error
kbuild: make built-in.a rule robust against too long argument error
kbuild: check static EXPORT_SYMBOL* by script instead of modpost
parisc: remove arch/parisc/nm
kbuild: do not create *.prelink.o for Clang LTO or IBT
kbuild: replace $(linked-object) with CONFIG options
kbuild: do not try to parse *.cmd files for objects provided by compiler
kbuild: replace $(if A,A,B) with $(or A,B) in scripts/Makefile.modpost
modpost: squash if...else-if in find_elf_symbol2()
modpost: reuse ARRAY_SIZE() macro for section_mismatch()
...
Linus Torvalds [Sun, 5 Jun 2022 02:07:15 +0000 (19:07 -0700)]
Merge tag 'pull-18-rc1-work.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pathname updates from Al Viro:
"Several cleanups in fs/namei.c"
* tag 'pull-18-rc1-work.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
namei: cleanup double word in comment
get rid of dead code in legitimize_root()
fs/namei.c:reserve_stack(): tidy up the call of try_to_unlazy()
Linus Torvalds [Sun, 5 Jun 2022 02:00:05 +0000 (19:00 -0700)]
Merge tag 'pull-18-rc1-work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull mount handling updates from Al Viro:
"Cleanups (and one fix) around struct mount handling.
The fix is usermode_driver.c one - once you've done kern_mount(), you
must kern_unmount(); simple mntput() will end up with a leak. Several
failure exits in there messed up that way... In practice you won't hit
those particular failure exits without fault injection, though"
* tag 'pull-18-rc1-work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
move mount-related externs from fs.h to mount.h
blob_to_mnt(): kern_unmount() is needed to undo kern_mount()
m->mnt_root->d_inode->i_sb is a weird way to spell m->mnt_sb...
linux/mount.h: trim includes
uninline may_mount() and don't opencode it in fspick(2)/fsopen(2)
Linus Torvalds [Sun, 5 Jun 2022 01:52:00 +0000 (18:52 -0700)]
Merge tag 'pull-18-rc1-work.fd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull file descriptor updates from Al Viro.
- Descriptor handling cleanups
* tag 'pull-18-rc1-work.fd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Unify the primitives for file descriptor closing
fs: remove fget_many and fput_many interface
io_uring_enter(): don't leave f.flags uninitialized
Linus Torvalds [Sun, 5 Jun 2022 00:42:33 +0000 (17:42 -0700)]
Merge tag '5.19-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
"Nine cifs/smb3 client fixes.
Includes DFS fixes, some cleanup of leagcy SMB1 code, duplicated
message cleanup and a double free and deadlock fix"
* tag '5.19-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix uninitialized pointer in error case in dfs_cache_get_tgt_share
cifs: skip trailing separators of prefix paths
cifs: update internal module number
cifs: version operations for smb20 unneeded when legacy support disabled
cifs: do not build smb1ops if legacy support is disabled
cifs: fix potential deadlock in direct reclaim
cifs: when extending a file with falloc we should make files not-sparse
cifs: remove repeated debug message on cifs_put_smb_ses()
cifs: fix potential double free during failed mount
Masahiro Yamada [Mon, 30 May 2022 09:01:38 +0000 (18:01 +0900)]
modpost: simplify mod->name allocation
mod->name is set to the ELF filename with the suffix ".o" stripped.
The current code calls strdup() and free() to manipulate the string,
but a simpler approach is to pass new_module() with the name length
subtracted by 2.
Also, check if the passed filename ends with ".o" before stripping it.
The current code blindly chops the suffix:
tmp[strlen(tmp) - 2] = '\0'
It will cause buffer under-run if strlen(tmp) < 2;
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Masahiro Yamada [Sat, 28 May 2022 15:47:04 +0000 (00:47 +0900)]
kbuild: factor out the common objtool arguments
scripts/Makefile.build and scripts/link-vmlinux.sh have similar setups
for the objtool arguments.
It was difficult to factor out them because all the vmlinux build rules
were written in a shell script. It is somewhat tedious to touch the two
files every time a new objtool option is supported.
To reduce the code duplication, move the objtool for vmlinux.o into
scripts/Makefile.vmlinux_o. Then, move the common macros to Makefile.lib
so they are shared between Makefile.build and Makefile.vmlinux_o.
Linus Torvalds [Sat, 4 Jun 2022 21:04:27 +0000 (14:04 -0700)]
Merge tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
Linus Torvalds [Sat, 4 Jun 2022 20:50:23 +0000 (13:50 -0700)]
Merge tag 'for-5.19/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc architecture updates from Helge Deller:
"A fix to prevent crash at bootup if CONFIG_SCHED_MC is enabled, and
add auto-detection of primary graphics card for framebuffer driver"
* tag 'for-5.19/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc/stifb: Keep track of hardware path of graphics card
parisc/stifb: Implement fb_is_primary_device()
parisc: fix a crash with multicore scheduler
Linus Torvalds [Sat, 4 Jun 2022 20:42:53 +0000 (13:42 -0700)]
Merge tag 'for-linus-5.19-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
"Two cleanup patches for Xen related code and (more important) an
update of MAINTAINERS for Xen, as Boris Ostrovsky decided to step
down"
* tag 'for-linus-5.19-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: replace xen_remap() with memremap()
MAINTAINERS: Update Xen maintainership
xen: switch gnttab_end_foreign_access() to take a struct page pointer
Linus Torvalds [Sat, 4 Jun 2022 20:33:12 +0000 (13:33 -0700)]
Merge tag 'perf-tools-for-v5.19-2022-06-04' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Synthesize task events for pre-existing threads when using 'perf lock
--threads', as we need to show task names.
- Fix unwinding with ld.lld (>= version 10.0) linked objects, where
.eh_frame_hdr and .text are in different PT_LOAD program headers,
which makes perf record --call-graph dwarf fail with such obkects.
- Check if 'perf record' hangs in the ARM SPE (Statistical Profiling
Extensions) 'perf test' entry when recording a workload with forks.
- Trace physical address for Arm SPE events, needed for 'perf c2c' to
locate the memory node for samples.
- Fix sorting in percent_rmt_hitm_cmp() in 'perf c2c'.
- Further support for Intel hybrid systems in the evlist and 'perf
record' code.
- Update IBM s/390 vendor event JSON tables.
- Add metrics (JSON) for Intel Sapphirerapids.
- Update metrics for Intel Alderlake.
- Correct typo of sysf 'event_source' directory in the documentation.
* tag 'perf-tools-for-v5.19-2022-06-04' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf vendor events intel: Update metrics for Alderlake
perf vendor events intel: Add metrics for Sapphirerapids
perf c2c: Fix sorting in percent_rmt_hitm_cmp()
perf mem: Trace physical address for Arm SPE events
perf list: Update event description for IBM zEC12/zBC12 to latest level
perf list: Update event description for IBM z196/z114 to latest level
perf list: Update event description for IBM z15 to latest level
perf list: Update event description for IBM z14 to latest level
perf list: Update event description for IBM z13 to latest level
perf list: Update event description for IBM z10 to latest level
perf list: Add IBM z16 event description for s390
perf record: Support sample-read topdown metric group for hybrid platforms
perf lock: Change to synthesize task events
perf unwind: Fix segbase for ld.lld linked objects
perf test arm-spe: Check if perf-record hangs when recording workload with forks
perf docs: Correct typo of event_sources
perf evlist: Extend arch_evsel__must_be_in_group to support hybrid systems
Helge Deller [Thu, 2 Jun 2022 11:50:44 +0000 (13:50 +0200)]
parisc/stifb: Implement fb_is_primary_device()
Implement fb_is_primary_device() function, so that fbcon detects if this
framebuffer belongs to the default graphics card which was used to start
the system.
Linus Torvalds [Sat, 4 Jun 2022 03:01:25 +0000 (20:01 -0700)]
Merge tag 'gpio-fixes-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- use the correct register for regcache sync in gpio-pca953x
- remove unused and potentially harmful code from gpio-adp5588
- MAINTAINERS update
* tag 'gpio-fixes-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: adp5588: Remove support for platform setup and teardown callbacks
gpio: pca953x: use the correct register address to do regcache sync
MAINTAINERS: Update Intel GPIO (PMIC and PCH) to Supported
MAINTAINERS: Update GPIO ACPI library to Supported
Linus Torvalds [Sat, 4 Jun 2022 02:57:25 +0000 (19:57 -0700)]
Merge tag 'regulator-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"One fix that came in during the merge window, fixing an error in the
examples in the DT binding documentation for mt6315"
* tag 'regulator-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: mt6315-regulator: fix invalid allowed mode
projects / kernel.git / log