Avri Altman [Tue, 26 Feb 2019 15:10:24 +0000 (17:10 +0200)]
mmc: core: Add discard support to sd
SD spec v5.1 adds discard support. The flows and commands are similar to
mmc, so just set the discard arg in CMD38.
A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313)
is set in the SD_STATUS register. If the card does not support discard,
the host shall not issue DISCARD command, but ERASE command instead.
Post the DISCARD operation, the card may de-allocate the discarded
blocks partially or completely. So the host mustn't make any assumptions
concerning the content of the discarded region. This is unlike ERASE
command, in which the region is guaranteed to contain either '0's or
'1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr
register.
One more important difference compared to ERASE is the busy timeout
which we will address on the next patch.
BOUGH CHEN [Wed, 27 Feb 2019 08:24:48 +0000 (08:24 +0000)]
mmc: sdhci-esdhc-imx: clear the HALT bit when enable CQE
After system suspend, CQE is in cqhci_off state, which set the HALT bit, make
CQE in HALT state. If the SoC do not power down the USDHC module, then when
system resume back, this bit keep the same, still set. Though there is a
sdhci reset during sdhci_resume_host(), but this reset do not impact the
CQE part, so need to clear this bit when enable CQE, otherwise CQE will
stuck in the first CMDQ request after system resume back.
Chaotian Jing [Fri, 15 Feb 2019 05:59:34 +0000 (13:59 +0800)]
mmc: core: do not retry CMD6 in __mmc_switch()
the response type of CMD6 is R1B, when the first CMD6 gets response
CRC error, do retry may get timeout error due to card may still in
busy state, which cause this retry make no sense.
Ming Lei [Wed, 27 Feb 2019 16:02:11 +0000 (00:02 +0800)]
mmc: core: align max segment size with logical block size
Logical block size is the lowest possible block size that the storage
device can address. Max segment size is often related with controller's
DMA capability. And it is reasonable to align max segment size with
logical block size.
SDHCI sets un-aligned max segment size, and causes ADMA error, so
fix it by aligning max segment size with logical block size.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Christoph Hellwig <hch@lst.de> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Faiz Abbas <faiz_abbas@ti.com> Cc: linux-block@vger.kernel.org Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alamy Liu [Mon, 25 Feb 2019 19:22:14 +0000 (11:22 -0800)]
mmc: cqhci: Fix a tiny potential memory leak on error condition
Free up the allocated memory in the case of error return
The value of mmc_host->cqe_enabled stays 'false'. Thus, cqhci_disable
(mmc_cqe_ops->cqe_disable) won't be called to free the memory. Also,
cqhci_disable() seems to be designed to disable and free all resources, not
suitable to handle this corner case.
Fixes: 86a0b29c15a4 ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Alamy Liu <alamy.liu@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Alamy Liu [Mon, 25 Feb 2019 19:22:13 +0000 (11:22 -0800)]
mmc: cqhci: fix space allocated for transfer descriptor
There is not enough space being allocated when DCMD is disabled.
CQE_DCMD is not necessary to be enabled when CQE is enabled.
(Software could halt CQE to send command)
In the case that CQE_DCMD is not enabled, it still needs to allocate
space for data transfer. For instance:
CQE_DCMD is enabled: 31 slots space (one slot used by DCMD)
CQE_DCMD is disabled: 32 slots space
Fixes: 86a0b29c15a4 ("mmc: cqhci: support for command queue enabled host") Signed-off-by: Alamy Liu <alamy.liu@gmail.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ritesh Harjani [Fri, 22 Feb 2019 13:51:34 +0000 (19:21 +0530)]
mmc: core: Fix NULL ptr crash from mmc_should_fail_request
In case of CQHCI, mrq->cmd may be NULL for data requests (non DCMD).
In such case mmc_should_fail_request is directly dereferencing
mrq->cmd while cmd is NULL.
Fix this by checking for mrq->cmd pointer.
Fixes: 24d778b694c9 ("mmc: core: Add support for handling CQE requests") Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Takeshi Saito [Thu, 21 Feb 2019 19:38:05 +0000 (20:38 +0100)]
mmc: tmio: fix access width of Block Count Register
In R-Car Gen2 or later, the maximum number of transfer blocks are
changed from 0xFFFF to 0xFFFFFFFF. Therefore, Block Count Register
should use iowrite32().
If another system (U-boot, Hypervisor OS, etc) uses bit[31:16], this
value will not be cleared. So, SD/MMC card initialization fails.
So, check for the bigger register and use apropriate write. Also, mark
the register as extended on Gen2.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: use max_blk_count in if(), add Gen2, update commit message] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@kernel.org Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
[Ulf: Fixed build error] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I have encountered an interrupt storm during the eMMC chip probing (and
the chip finally didn't get detected). It turned out that U-Boot left
the DMAC interrupts enabled while the Linux driver didn't use those.
The SDHI driver's interrupt handler somehow assumes that, even if an
SDIO interrupt didn't happen, it should return IRQ_HANDLED. I think
that if none of the enabled interrupts happened and got handled, we
should return IRQ_NONE -- that way the kernel IRQ code recoginizes
a spurious interrupt and masks it off pretty quickly...
Fixes: a47eb0dfa375 ("mmc: tmio: Provide separate interrupt handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Wed, 13 Feb 2019 19:03:30 +0000 (20:03 +0100)]
mmc: core: Convert mmc_align_data_size() into an SDIO specific function
The only user of mmc_align_data_size() is sdio_align_size(), which is
called from SDIO func drivers to let them distinguish, how to optimally
allocate data buffers.
Let's move mmc_align_data_size() close to the SDIO code as to make it
static, rename it to _sdio_align_size() and simplify its definition, all
with the purpose of clarifying that this is SDIO specific.
When using the mmc_spi driver with a card-detect pin, I noticed that the
card was not detected immediately after probe, but only after it was
unplugged and plugged back in (and the CD IRQ fired).
Ulf Hansson [Wed, 13 Feb 2019 17:46:45 +0000 (18:46 +0100)]
mmc: core: Move mmc_of_parse_voltage() to host.c
MMC OF parsing functions, which parses various host DT properties, should
stay close to each other. Therefore, let's move mmc_of_parse_voltage()
close to mmc_of_parse() into host.c.
Additionally, there is no reason to build the code only when CONFIG_OF is
set, as there should be stub functions for the OF helpers that is being
used, so let's drop this condition as well.
Ulf Hansson [Wed, 13 Feb 2019 17:10:37 +0000 (18:10 +0100)]
mmc: core: Move regulator helpers to separate file
The mmc regulator helper functions, are placed in the extensive core.c
file. In a step towards trying to create a better structure of files,
avoiding too many lines of code per file, let's move these helpers to a new
file, regulator.c.
Moreover, this within this context it makes sense to also drop the export
of mmc_vddrange_to_ocrmask(), but instead let's make it internal to the mmc
core.
Ulf Hansson [Wed, 13 Feb 2019 14:17:13 +0000 (15:17 +0100)]
mmc: core: Drop retries as in-parameter to mmc_wait_for_app_cmd()
All callers of mmc_wait_for_app_cmd() set the retries in-parameter to
MMC_CMD_RETRIES. This is silly, so let's just drop the in-parameter
altogether, as to simplify the code.
Ulf Hansson [Tue, 29 Jan 2019 14:35:56 +0000 (15:35 +0100)]
mmc: mmci: Send a CMD12 to clear the DPSM at errors
The current approach with sending a CMD12 (STOP_TRANSMISSION) to complete a
data transfer request, either because of using the open-ended transmission
type or because of receiving an error during a pre-defined data transfer,
isn't sufficient for the STM32 sdmmc variant. More precisely, this variant
needs to clear the DPSM ("Data Path State Machine") by sending a CMD12, for
all failing ADTC commands.
Support this, by adding a struct mmc_command inside the struct mmci_host
and initialize it to a CMD12 during ->probe(). Let's also add checks for
the new conditions, to enable mmci_data_irq() and mmci_cmd_irq() to
postpone the calls to mmci_request_end(), but instead send the CMD12.
Thomas Petazzoni [Tue, 12 Feb 2019 14:07:37 +0000 (15:07 +0100)]
mmc: sdhci-tegra: drop ->get_ro() implementation
The SDHCI core is know properly checking for the state of a WP GPIO,
so there is no longer any need for the sdhci-tegra code to implement
->get_ro() using mmc_gpio_get_ro().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Tested-by: Thierry Reding <treding@nvidia.com> Acked-by: Thierry Reding <treding@nvidia.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Thomas Petazzoni [Tue, 12 Feb 2019 14:07:36 +0000 (15:07 +0100)]
mmc: sdhci-omap: drop ->get_ro() implementation
The SDHCI core is now properly checking for the state of a WP GPIO,
so there is no longer any need for the sdhci-omap code to implement
->get_ro() using mmc_gpio_get_ro().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Thomas Petazzoni [Tue, 12 Feb 2019 14:07:35 +0000 (15:07 +0100)]
mmc: sdhci: use WP GPIO in sdhci_check_ro()
Even though SDHCI controllers may have a dedicated WP pin that can be
queried using the SDHCI_PRESENT_STATE register, some platforms may
chose to use a separate regular GPIO to route the WP signal. Such a
GPIO is typically represented using the wp-gpios property in the
Device Tree.
Unfortunately, the current sdhci_check_ro() function does not make use
of such GPIO when available: it either uses a host controller specific
->get_ro() operation, or uses the SDHCI_PRESENT_STATE. Several host
controller specific ->get_ro() functions are implemented just to check
a WP GPIO state.
Instead of pushing this to more controller-specific implementations,
let's handle this in the core SDHCI code, just like it is already done
for the CD GPIO in sdhci_get_cd().
The below patch simply changes sdhci_check_ro() to use the value of
the WP GPIO if available.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Avri Altman [Wed, 6 Feb 2019 11:28:05 +0000 (13:28 +0200)]
mmc: core: Calculate the discard arg only once
In MMC, the discard arg is a read-only ext_csd parameter - set it once
on card init. To be consistent, do that for SD as well even though its
discard arg is always 0x0.
Linus Walleij [Tue, 5 Feb 2019 09:30:22 +0000 (10:30 +0100)]
mmc: slot-gpio: Remove override_active_level on WP
The argument "override_active_level" made it possible to
enforce a specific polarity on the write-protect
GPIO line. All callers in the kernel pass "false" to this
call after I have converted all drivers to use GPIO machine
descriptors, so remove the argument and clean out this.
This kind of polarity inversion should be handled by the
GPIO descriptor inside the GPIO library if needed.
This rids us of one instance of the kludgy calls into
the gpiod_get_raw_value() API.
Lukas Wunner [Sun, 3 Feb 2019 08:27:00 +0000 (09:27 +0100)]
mmc: bcm2835: Deduplicate reset of driver data on remove
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Lukas Wunner [Sun, 3 Feb 2019 08:27:00 +0000 (09:27 +0100)]
mmc: bcm2835: Drop pointer to mmc_host from bcm2835_host
The BCM2835 MMC host driver uses a pointer to get from the private
bcm2835_host structure to the generic mmc_host structure. However the
latter is always immediately preceding the former in memory, so compute
its address with a subtraction (which is cheaper than a dereference) and
drop the superfluous pointer.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Cc: Alexander Graf <agraf@suse.de> Reviewed-by: Alexander Graf <agraf@suse.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Lukas Wunner [Sun, 3 Feb 2019 08:27:00 +0000 (09:27 +0100)]
mmc: bcm2835: Drop DMA channel error pointer check
bcm2835_add_host() invokes IS_ERR_OR_NULL() on a DMA channel pointer,
however dma_request_slave_channel() (which was used to populate the
pointer) never returns an error pointer. So a NULL pointer check is
sufficient.
Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: Frank Pavlic <f.pavlic@kunbus.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Aaro Koskinen [Sat, 2 Feb 2019 22:14:33 +0000 (00:14 +0200)]
mmc: omap: fix the maximum timeout setting
When running OMAP1 kernel on QEMU, MMC access is annoyingly noisy:
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
MMC: CTO of 0xff and 0xfe cannot be used!
[ad inf.]
Emulator warnings appear to be valid. The TI document SPRU680 [1]
("OMAP5910 Dual-Core Processor MultiMedia Card/Secure Data Memory Card
(MMC/SD) Reference Guide") page 36 states that the maximum timeout is 253
cycles and "0xff and 0xfe cannot be used".
Fix by using 0xfd as the maximum timeout.
Tested using QEMU 2.5 (Siemens SX1 machine, OMAP310), and also checked on
real hardware using Palm TE (OMAP310), Nokia 770 (OMAP1710) and Nokia N810
(OMAP2420) that MMC works as before.
mmc: sdhci: Add ADMA3 DMA support for V4 enabled host
Below are the supported DMA types in Host Control1 Register
with Version 4 enable
b'00 - SDMA
b'01 - Not Used
b'10 - ADMA2
b'11 - ADMA2 or ADMA3
ADMA3 uses Command Descriptor to issue an SD command.
A multi-block data transfer is performed by using a pair of CMD
descriptor and ADMA2 descriptor.
ADMA3 performs multiple of multi-block data transfer by using
Integrated Descriptor which is more suitable for Command Queuing
to fetch both Command and Transfer descriptors.
Host Capabilities register indicates the supports of ADMA3 DMA.
Ulf Hansson [Wed, 30 Jan 2019 09:04:31 +0000 (10:04 +0100)]
MAINTAINERS: Add maintainers for eMMC CQHCI driver
The eMMC CQHCI is the host controller interface, introduced in the eMMC
spec v5.1. The code was originally developed as collaboration among several
people, however none really stepped in to maintain it.
Let's add Adrian Hunter (Intel), Ritesh Harjani and Asutosh Das as the
maintainers, whom knows both the code and the spec.
Cc: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Ritesh Harjani <riteshh@codeaurora.org> Acked-by: Asutosh Das <asutoshd@codeaurora.org>
Takeshi Saito [Tue, 29 Jan 2019 05:40:39 +0000 (06:40 +0100)]
mmc: renesas_sdhi: Fix card initialization failure in high speed mode
This fixes card initialization failure in high speed mode.
If U-Boot uses SDR or HS200/400 mode before starting Linux and Linux
DT does not enable SDR/HS200/HS400 mode, card initialization fails in
high speed mode.
It is necessary to initialize SCC registers during card initialization
phase. HW reset function is registered only for a port with either of
SDR/HS200/HS400 properties in device tree. If SDR/HS200/HS400 properties
are not present in device tree, SCC registers will not be reset. In SoC
that support SCC registers, HW reset function should be registered
regardless of the configuration of device tree.
Reproduction procedure:
- Use U-Boot that support MMC HS200/400 mode.
- Delete HS200/HS400 properties in device tree.
(Delete mmc-hs200-1_8v and mmc-hs400-1_8v)
- MMC port works high speed mode and all commands fail.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Cc: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ernest Zhang(WH) [Fri, 18 Jan 2019 06:04:53 +0000 (06:04 +0000)]
mmc: sdhci: Remove unneeded quirk2 flag of O2 SD host controller
O2 SD host controller only need set the quirk2 flag
SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD when
work on force 1.8v emmc mode but not normal mode
Signed-off-by: Ernest Zhang <ernest.zhang@bayhubtech.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1).
This commit removes the following warnings:
drivers/mmc/host/jz4740_mmc.c:745:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/mmc/host/jz4740_mmc.c:779:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Wei Yongjun [Wed, 16 Jan 2019 05:44:51 +0000 (05:44 +0000)]
mmc: sdhci-esdhc-imx: fix return value check in sdhci_esdhc_imx_probe()
In case of error, the function devm_kzalloc() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
There is a plan to build the kernel with -Wimplicit-fallthrough and
this place in the code produced a warning (W=1).
In this particular case rewrote the comment to start with the string "fall
through", so as to match the regular expression expected by GCC. Truncate
the comment slightly to fit the max line length of 80 characters.
This commit remove the following warning:
drivers/mmc/core/host.c:196:14: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program initial drive code offsets which will be used by auto
calibration process.
Program fixed drive strengths for SDMMC pads in pad control
register when auto cal timeouts.
Fixed settings are based on Pre-SI analysis of the pad design.
dt-bindings: mmc: tegra: Add pinctrl for SDMMC drive strengths
Add pinctrls for 3V3 and 1V8 pad drive strength configuration for
Tegra210 sdmmc.
Tegra210 sdmmc has pad configuration registers in pinmux register
domain and handled thru pinctrl to pinmux device node.
Tegra186 and Tegra194 has pad configuration register with in the
SDMMC register domain itself and are handles thru drive strength
properties in sdmmc device node.
BOUGH CHEN [Mon, 7 Jan 2019 10:11:42 +0000 (10:11 +0000)]
mmc: sdhci-esdhc-imx: add DCMD support for CMDQ
Currently, USDHC do not generate transfer complete interrupt
when send a non-data-command with R1b response. But if want
to support DCMD in CMDQ, need to change this, the DCMD IC
logic require the USDHC to enable this function, otherwise
DCMD will never get a CC(command complete) interrupt.
This patch set ESDHC_VEND_SPEC2_EN_BUSY_IRQ and add DCMD support.
BOUGH CHEN [Mon, 7 Jan 2019 10:11:39 +0000 (10:11 +0000)]
mmc: sdhci-esdhc-imx: add CMDQ support
Add CMDQ support for imx8qm/imx8qxp.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased on top of latest changes] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BOUGH CHEN [Mon, 7 Jan 2019 10:11:36 +0000 (10:11 +0000)]
mmc: sdhci: correct the maximum timeout when enable CMDQ
Change to use sdhci_set_timeout() to set the maximum timeout, so that
the host can use it's own set_timeout() callback to set the maximum
timeout if the host has.
BOUGH CHEN [Mon, 7 Jan 2019 10:11:32 +0000 (10:11 +0000)]
mmc: sdhci-esdhc-imx: add HS400_ES support for i.MX8QXP
Add an new esdhc_soc_data for i.MX8QXP, and add HS400_ES mode
support.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Rebased on top of latest changes] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BOUGH CHEN [Mon, 7 Jan 2019 10:11:29 +0000 (10:11 +0000)]
mmc: sdhci-esdhc-imx: remove the 100MHz limitation for Strobe DLL
For some eMMC, after switch to HS400ES mode, it need to config the strobe
dll target dealy even if the clock is 50MHZ or 25MHz, otherwise will meet
CMD index/crc error when send CMD13 to check the switch status.
1. O2 Host Controller PLL lock status is not in compliance with
CLOCK_CONTROL register bit 1
2. O2 Host Controller card detect function only work when PLL is
enabled and locked
Signed-off-by: Ernest Zhang <ernest.zhang@bayhubtech.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BOUGH CHEN [Fri, 28 Dec 2018 08:35:49 +0000 (08:35 +0000)]
mmc: sdhci: add delay after the last tuning command
When host set the host->tuning_delay, even the last tuning
command need a delay, otherwise the first command after the
tuning will meet issue.
Take i.MX7D as an example, there will be the following log:
mmc2: switch to high-speed from hs200 failed, err:-110
mmc2: error -110 whilst initialising MMC card
BOUGH CHEN [Fri, 28 Dec 2018 03:26:10 +0000 (03:26 +0000)]
mmc: sdhci-esdhc-imx: add SD clock limitation for imx6ull
i.MX6ULL has errata ERR010450, point out that due to SOC I/O
timing limitation, for eMMC HS200 and SD/SDIO 3.0 SDR104, the
clock rate can't exceed 150MHz. And for eMMC DDR52 and SD/SDIO
DDR50 mode, the clock rate can't exceed 45MHz.
This patch add this limit for imx6ull.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed comments and whitespace] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BOUGH CHEN [Thu, 27 Dec 2018 11:20:24 +0000 (11:20 +0000)]
mmc: sdhci-esdhc-imx: fix HS400 timing issue
Now tuning reset will be done when the timing is MMC_TIMING_LEGACY/
MMC_TIMING_MMC_HS/MMC_TIMING_SD_HS. But for timing MMC_TIMING_MMC_HS,
we can not do tuning reset, otherwise HS400 timing is not right.
Here is the process of init HS400, first finish tuning in HS200 mode,
then switch to HS mode and 8 bit DDR mode, finally switch to HS400
mode. If we do tuning reset in HS mode, this will cause HS400 mode
lost the tuning setting, which will cause CRC error.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Cc: stable@vger.kernel.org # v4.12+ Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: fae62463bb1a ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BOUGH CHEN [Fri, 21 Dec 2018 09:20:53 +0000 (09:20 +0000)]
mmc: sdhci: usdhc: do not do tuning for DDR50 mode.
DDR50 tuning is optinally defined in sd 3.0 spec. And i.MX
uSDHC internally already uses a fixed optimized timing for
DDR50, normally does not require tuning for DDR50 mode.
This patch specify a new execute_tuning function for i.MX
uSDHC, do not impact i.MX eSDHC.
BOUGH CHEN [Thu, 20 Dec 2018 11:57:41 +0000 (11:57 +0000)]
mmc: sdhci-esdhc-imx: clear ESDHC_STD_TUNING_EN for manual tuning method
The bit ESDHC_STD_TUNING_EN may be configed by bootloader code if it
choose to use standard tuning method. So on linux side, if choose to
use manual tuning method, need to clear the bit ESDHC_STD_TUNING_EN,
remove the impact of bootloader code.
Linus Torvalds [Sun, 24 Feb 2019 17:47:07 +0000 (09:47 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
Linus Walleij [Sun, 24 Feb 2019 00:11:15 +0000 (01:11 +0100)]
net: phy: realtek: Dummy IRQ calls for RTL8366RB
This fixes a regression introduced by
commit 3f8451dadb9d4e784673da75cb1f219455d39f0d
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 3f8451dadb9d ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt") Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 23 Feb 2019 21:24:59 +0000 (13:24 -0800)]
net/x25: fix a race in x25_bind()
syzbot was able to trigger another soft lockup [1]
I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.
This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list
Fixes: aa00142fe2a3 ("X.25 remove bkl in bind") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: andrew hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 22 Feb 2019 13:22:32 +0000 (21:22 +0800)]
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
This reverts commit e86a3d48bc7f ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 7ca814f685f2 ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de> Fixes: e86a3d48bc7f ("bridge: do not add port to router list when receives query with source 0.0.0.0") Fixes: 7ca814f685f2 ("net: bridge: remove ipv6 zero address check in mcast queries") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: fib_tests: sleep after changing carrier. again.
Just like commit adfbfc0aca3a ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Fri, 22 Feb 2019 06:57:23 +0000 (14:57 +0800)]
net: set static variable an initial value in atl2_probe()
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 96b4c6baf6d8 ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reported-by: Russell King <linux@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 17:48:01 +0000 (09:48 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 01:46:30 +0000 (17:46 -0800)]
Merge tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
Linus Torvalds [Sat, 23 Feb 2019 00:31:26 +0000 (16:31 -0800)]
Merge tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
Daniel Borkmann [Fri, 22 Feb 2019 23:03:44 +0000 (00:03 +0100)]
bpf, doc: add bpf list as secondary entry to maintainers file
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Sat, 23 Feb 2019 00:12:01 +0000 (16:12 -0800)]
Merge branch 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
Linus Torvalds [Sat, 23 Feb 2019 00:09:55 +0000 (16:09 -0800)]
Merge tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
* tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
sh: fix build error for invisible CONFIG_BUILTIN_DTB_SOURCE
kallsyms: Handle too long symbols in kallsyms.c
David S. Miller [Sat, 23 Feb 2019 00:05:12 +0000 (16:05 -0800)]
Merge branch 'udp-a-few-fixes'
Paolo Abeni says:
====================
udp: a few fixes
This series includes some UDP-related fixlet. All this stuff has been
pointed out by the sparse tool. The first two patches are just annotation
related, while the last 2 cover some very unlikely races.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:44:00 +0000 (17:44 +0100)]
udp: fix possible user after free in error handler
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: 51baa94611d1 ("udp: Support for error handlers of tunnels with arbitrary destination port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:59 +0000 (17:43 +0100)]
udpv6: fix possible user after free in error handler
Before derefencing the encap pointer, commit 51baa94611d1 ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: 51baa94611d1 ("udp: Support for error handlers of tunnels with arbitrary destination port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>