Maxime Ripard [Mon, 16 Apr 2018 12:36:55 +0000 (08:36 -0400)]
media: ov5640: Add horizontal and vertical totals
All the initialization arrays are changing the horizontal and vertical
totals for some value.
In order to clean up the driver, and since we're going to need that value
later on, let's introduce in the ov5640_mode_info structure the horizontal
and vertical total sizes, and move these out of the bytes array.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Maxime Ripard [Mon, 16 Apr 2018 12:36:53 +0000 (08:36 -0400)]
media: ov5640: Init properly the SCLK dividers
The SCLK and SCLK2X dividers are fixed in stone in the initialization
array. Let's make explicit what we're doing and move that away from the
huge array to the initialization code.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Maxime Ripard [Mon, 16 Apr 2018 12:36:52 +0000 (08:36 -0400)]
media: ov5640: Don't force the auto exposure state at start time
The sensor needs to have the auto exposure stopped while changing mode.
However, when the new mode is set, the driver will force the auto exposure
on, disregarding whether the control has been changed or not.
Bypass the controls code entirely to do that, and only use the control
value cached when restoring the auto exposure mode.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Akinobu Mita [Sat, 10 Feb 2018 15:28:38 +0000 (10:28 -0500)]
media: ov2640: make s_ctrl() work in power-down mode
The s_ctrl() operation can be called when the device is placed into
power down mode. Then, applying controls to H/W should be postponed at
this time. Instead the controls will be restored when the streaming is
started.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Akinobu Mita [Sat, 10 Feb 2018 15:28:37 +0000 (10:28 -0500)]
media: ov2640: make set_fmt() work in power-down mode
The set_fmt() subdev pad operation for this driver currently does not
only do the driver internal format selection but also do the actual
register setup.
This doesn't work if the device power control via GPIO lines is enabled.
Because the set_fmt() can be called when the device is placed into power
down mode.
First of all, this fix adds flag to keep track of whether the device starts
streaming or not. Then, the set_fmt() postpones applying the actual
register setup at this time. Instead the setup will be applied when the
streaming is started.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sakari Ailus [Tue, 24 Apr 2018 10:25:47 +0000 (06:25 -0400)]
media: ov5640: Use dev_fwnode() to obtain device's fwnode
Use dev_fwnode() on the device instead of getting an fwnode handle of the
device's OF node. The result is the same on OF-based systems and looks
better, too.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: drm: rcar-du: Add support for CRC computation
Implement CRC computation configuration and reporting through the DRM
debugfs-based CRC API. The CRC source can be configured to any input
plane or the pipeline output.
Laurent Pinchart [Thu, 30 Nov 2017 14:45:20 +0000 (09:45 -0500)]
media: v4l: vsp1: Integrate DISCOM in display pipeline
The DISCOM is used to compute CRCs on display frames. Integrate it in
the display pipeline at the output of the blending unit to process
output frames.
Computing CRCs on input frames is possible by positioning the DISCOM at
a different point in the pipeline. This use case isn't supported at the
moment and could be implemented by extending the API between the VSP1
and DU drivers if needed.
Laurent Pinchart [Mon, 27 Nov 2017 20:45:42 +0000 (15:45 -0500)]
media: v4l: vsp1: Add support for the DISCOM entity
The DISCOM calculates a CRC on a configurable window of the frame. It
interfaces to the VSP through the UIF glue, hence the name used in the
code.
The module supports configuration of the CRC window through the crop
rectangle on the sink pad of the corresponding entity. However, unlike
the traditional V4L2 subdevice model, the crop rectangle does not
influence the format on the source pad.
Modeling the DISCOM as a sink-only entity would allow adhering to the
V4L2 subdevice model at the expense of more complex code in the driver,
as at the hardware level the UIF is handled as a sink+source entity. As
the DISCOM is only present in R-Car Gen3 VSP-D and VSP-DL instances it
is not exposed to userspace through V4L2 but controlled through the DU
driver. We can thus change this model later if needed without fear of
affecting userspace.
media: v4l: vsp1: Extend the DU API to support CRC computation
Add a parameter (in the form of a structure to ease future API
extensions) to the VSP atomic flush handler to pass CRC source
configuration, and pass the CRC value to the completion callback.
Laurent Pinchart [Tue, 28 Nov 2017 00:27:32 +0000 (19:27 -0500)]
media: v4l: vsp1: Reset the crop and compose rectangles in the set_fmt helper
To make vsp1_subdev_set_pad_format() usable by entities that support
selection rectangles, we need to reset the crop and compose rectangles
when setting the format on the sink pad. Do so and replace the custom
set_fmt implementation of the histogram code by a call to
vsp1_subdev_set_pad_format().
Resetting the crop and compose rectangles for entities that don't
support crop and compose has no adverse effect as the rectangles are
ignored anyway.
Adopt the SPDX license identifier headers to ease license compliance
management. All files in the driver are licensed under the GPLv2+ except
for the vsp1_regs.h file which is licensed under the GPLv2. This is
likely an oversight, but fixing this requires contacting the copyright
owners and is out of scope for this patch.
While at it fix the file descriptions to match file names where copy and
paste error occurred.
The Cadence MIPI-CSI2 TX controller is an hardware block meant to be used
as a bridge between pixel interfaces and a CSI-2 bus.
It supports operating with an internal or external D-PHY, with up to 4
lanes, or without any D-PHY. The current code only supports the latter
case.
While the virtual channel input on the pixel interface can be directly
mapped to CSI2, the datatype input is actually a selection signal (3-bits)
mapping to a table of up to 8 preconfigured datatypes/formats (programmed
at start-up)
Maxime Ripard [Fri, 4 May 2018 14:08:09 +0000 (10:08 -0400)]
media: dt-bindings: media: Add Cadence MIPI-CSI2 TX Device Tree bindings
The Cadence MIPI-CSI2 TX controller is a CSI2 bridge that supports up to 4
video streams and can output on up to 4 CSI-2 lanes, depending on the
hardware implementation.
It can operate with an external D-PHY, an internal one or no D-PHY at all
in some configurations.
Acked-by: Benoit Parrot <bparrot@ti.com> Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Maxime Ripard [Fri, 4 May 2018 14:08:07 +0000 (10:08 -0400)]
media: dt-bindings: media: Add Cadence MIPI-CSI2 RX Device Tree bindings
The Cadence MIPI-CSI2 RX controller is a CSI2RX bridge that supports up to
4 CSI-2 lanes, and can route the frames to up to 4 streams, depending on
the hardware implementation.
It can operate with an external D-PHY, an internal one or no D-PHY at all
in some configurations.
Acked-by: Rob Herring <robh@kernel.org> Acked-by: Benoit Parrot <bparrot@ti.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sakari Ailus [Wed, 9 May 2018 14:34:45 +0000 (17:34 +0300)]
media: staging: atomisp: Remove driver
The atomisp driver has a long list of todo items and little has been done
to address these lately while more has been added. The driver is also not
functional. In other words, the driver would not be getting out of staging
in the foreseeable future. At the same time it consumes developer
resources in order to maintain the flaky code base. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are lots of data structs defined there but aren't used
anywhere.
Comment them out. Gets rid of those warnings:
drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:1808:45: warning: 'mt9m114_entity_ops' defined but not used [-Wunused-const-variable=]
static const struct media_entity_operations mt9m114_entity_ops = {
^~~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:35:0:
drivers/staging/media/atomisp/i2c/mt9m114.h:805:34: warning: 'mt9m114_iq' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_iq[] = {
^~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:797:34: warning: 'mt9m114_antiflicker_60hz' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_antiflicker_60hz[] = {
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:789:34: warning: 'mt9m114_antiflicker_50hz' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_antiflicker_50hz[] = {
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:682:34: warning: 'mt9m114_720_480P_init' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_720_480P_init[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:533:34: warning: 'mt9m114_960P_init' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_960P_init[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:518:34: warning: 'mt9m114_wakeup_reg' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_wakeup_reg[] = {
^~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:504:34: warning: 'mt9m114_streaming' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_streaming[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:497:34: warning: 'mt9m114_suspend' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_suspend[] = {
^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:393:34: warning: 'mt9m114_exitstandby' defined but not used [-Wunused-const-variable=]
static struct misensor_reg const mt9m114_exitstandby[] = {
^~~~~~~~~~~~~~~~~~~
It seems that, originally, the logic would allow selecting between
fine and coarse integration. However, only coarse seems to be
implemented.
Get rid of this warning:
drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c: In function 'mt9m114_s_exposure':
drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:1003:6: warning: variable 'exposure_local' set but not used [-Wunused-but-set-variable]
u16 exposure_local[3];
^~~~~~~~~~~~~~
media: atomisp-gc0310: return errors at gc0310_init()
If something wrong gets there, return the error.
Get rid of this warning:
drivers/staging/media/atomisp/i2c/atomisp-gc0310.c: In function 'gc0310_init':
drivers/staging/media/atomisp/i2c/atomisp-gc0310.c:713:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘__ov2680_set_exposure’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:400:10: warning: variable ‘hts’ set but not used [-Wunused-but-set-variable]
u16 vts,hts;
^~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘ov2680_detect’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:1164:5: warning: variable ‘revision’ set but not used [-Wunused-but-set-variable]
u8 revision;
^~~~~~~~
media: staging: atomisp: Comment out several unused sensor resolutions
The register settings for several resolutions aren't used
currently. So, comment them out.
Fix those warnings:
In file included from drivers/staging/media/atomisp/i2c/atomisp-gc2235.c:35:0:
drivers/staging/media/atomisp/i2c/gc2235.h:340:32: warning: 'gc2235_960_640_30fps' defined but not used [-Wunused-const-variable=]
static struct gc2235_reg const gc2235_960_640_30fps[] = {
^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/gc2235.h:287:32: warning: 'gc2235_1296_736_30fps' defined but not used [-Wunused-const-variable=]
static struct gc2235_reg const gc2235_1296_736_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/atomisp-ov2722.c:35:0:
drivers/staging/media/atomisp/i2c/ov2722.h:999:32: warning: 'ov2722_720p_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_720p_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:787:32: warning: 'ov2722_1M3_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_1M3_30fps[] = {
^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:476:32: warning: 'ov2722_VGA_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_VGA_30fps[] = {
^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:367:32: warning: 'ov2722_480P_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_480P_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:257:32: warning: 'ov2722_QVGA_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2722_reg const ov2722_QVGA_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function '__ov2680_set_exposure':
In file included from drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:35:0:
At top level:
drivers/staging/media/atomisp/i2c/ov2680.h:736:33: warning: 'ov2680_1616x1082_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_1616x1082_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:649:33: warning: 'ov2680_1456x1096_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_1456x1096_30fps[]= {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:606:33: warning: 'ov2680_1296x976_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_1296x976_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:563:33: warning: 'ov2680_720p_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_720p_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:520:33: warning: 'ov2680_800x600_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_800x600_30fps[] = {
^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:475:33: warning: 'ov2680_720x592_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_720x592_30fps[] = {
^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:433:33: warning: 'ov2680_656x496_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_656x496_30fps[] = {
^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:389:33: warning: 'ov2680_QVGA_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_QVGA_30fps[] = {
^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:346:33: warning: 'ov2680_CIF_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_CIF_30fps[] = {
^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:301:33: warning: 'ov2680_QCIF_30fps' defined but not used [-Wunused-const-variable=]
static struct ov2680_reg const ov2680_QCIF_30fps[] = {
^~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/ov5693/atomisp-ov5693.c:36:0:
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:988:32: warning: 'ov5693_1424x1168_30fps' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1424x1168_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:954:32: warning: 'ov5693_2592x1944_30fps' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_2592x1944_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:889:32: warning: 'ov5693_2592x1456_30fps' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_2592x1456_30fps[] = {
^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:862:32: warning: 'ov5693_1940x1096' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1940x1096[] = {
^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:796:32: warning: 'ov5693_1636p_30fps' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1636p_30fps[] = {
^~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:758:32: warning: 'ov5693_1296x736' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1296x736[] = {
^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:730:32: warning: 'ov5693_976x556' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_976x556[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:672:32: warning: 'ov5693_736x496' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_736x496[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:643:32: warning: 'ov5693_192x160' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_192x160[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:616:32: warning: 'ov5693_368x304' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_368x304[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:587:32: warning: 'ov5693_336x256' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_336x256[] = {
^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:540:32: warning: 'ov5693_1296x976' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_1296x976[] = {
^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:509:32: warning: 'ov5693_654x496' defined but not used [-Wunused-const-variable=]
static struct ov5693_reg const ov5693_654x496[] = {
^~~~~~~~~~~~~~
media: staging: atomisp-gc2235: don't fill an unused var
The code with uses the dummy var is commented out. So,
coment out its definition/initialization.
Fix this warning:
drivers/staging/media/atomisp/i2c/atomisp-gc2235.c: In function 'gc2235_get_intg_factor':
drivers/staging/media/atomisp/i2c/atomisp-gc2235.c:249:26: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
u16 reg_val, reg_val_h, dummy;
^~~~~
Trivial fix to spelling mistake in ia_css_print message text
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: dvb_ca_en50221: prevent using slot_info for Spectre attacs
slot can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability,
as warned by smatch:
drivers/media/dvb-core/dvb_ca_en50221.c:1479 dvb_ca_en50221_io_write() warn: potential spectre issue 'ca->slot_info' (local cap)
Right now, the Siano's core uses GFP_DMA for both USB and
SDIO variants of the driver. There's no reason to use it
for USB. So, pass GFP_DMA as a parameter during sms core
register.
Matthias Reichl [Sun, 13 May 2018 11:24:31 +0000 (07:24 -0400)]
media: rc: ite-cir: lower timeout and extend allowed timeout range
The minimum possible timeout of ite-cir is 8 samples, which is
typically about 70us. The driver however changes the FIFO trigger
level from the hardware's default of 1 byte to 17 bytes, so the minimum
usable timeout value is 17 * 8 samples, which is typically about 1.2ms.
Tests showed that using timeouts down to 1.2ms actually work fine.
The current default timeout of 200ms is much longer than necessary and
the maximum timeout of 1s seems to have been chosen a bit arbitrarily.
So change the minimum timeout to the driver's limit of 17 * 8 samples
and bring timeout and maximum timeout in line with the settings
of many other receivers.
Signed-off-by: Matthias Reichl <hias@horus.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sean Young [Thu, 10 May 2018 10:14:38 +0000 (06:14 -0400)]
media: rc: decoders do not need to check for transitions
Drivers should never produce consecutive pulse or space raw events. Should
that occur, we would have bigger problems than this code is trying to
guard against.
Note that we already log an error should a driver misbehave.
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: dvb_frontend: cleanup some coding style errors
This is a core media file... it shoudn't have so many coding
style issues! The last patch ended by being submitted with
an error like that, very likely due to some cut and paste
issue.
Maybe it is time to clean it up. Do it with the auto
fix logic:
Max Kellermann [Thu, 3 May 2018 18:12:59 +0000 (14:12 -0400)]
media: dvbdev: add a mutex protecting the "mdev" pointer
During destruction, a race condition in
dvb_media_controller_disable_source() can cause a kernel crash,
because the "mdev" pointer has been read successfully while another
task executes dvb_usb_media_device_unregister(), which destroys the
object. Example for such a crash:
Hans Verkuil [Fri, 11 May 2018 14:57:07 +0000 (10:57 -0400)]
media: lgdt330x.h: fix compiler warning
Add missing 'inline' to fix this compiler warning:
In file included from drivers/media/common/b2c2/flexcop-fe-tuner.c:21:0:
drivers/media/dvb-frontends/lgdt330x.h:61:22: warning: 'lgdt330x_attach' defined but not used [-Wunused-function]
struct dvb_frontend *lgdt330x_attach(const struct lgdt330x_config *config,
^~~~~~~~~~~~~~~
Niklas Söderlund [Fri, 11 May 2018 14:41:26 +0000 (10:41 -0400)]
media: rcar-vin: fix crop and compose handling for Gen3
When refactoring the Gen3 enablement series crop and compose handling
where broken. This went unnoticed but can result in writing out side the
capture buffer. Fix this by restoring the crop and compose to reflect
the format dimensions as we have not yet enabled the scaler for Gen3.
Fixes: 7672deb9b60bb29d ("media: rcar-vin: use different v4l2 operations in media controller mode") Reported-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Niklas Söderlund [Fri, 11 May 2018 14:41:25 +0000 (10:41 -0400)]
media: Revert "media: rcar-vin: enable field toggle after a set number of lines for Gen3"
The offending commit was an attempt to fix the issue of writing outside
the capture buffer for VIN Gen3. Unfortunately it only fixed the symptom
of the problem to such a degree I could no longer reproduce it. Revert
the offending commit before a proper fix can be added in a follow-up
patch.
Trivial fix to spelling mistake in dprintk message text
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Anders Roxell [Tue, 8 May 2018 12:31:21 +0000 (08:31 -0400)]
media: usb: cx231xx-417: include linux/slab.h header
cx231-417 uses kmalloc/kfree functions, so slab header needs to be
included in order to fix the following build errors:
drivers/media/usb/cx231xx/cx231xx-417.c: In function ‘cx231xx_bulk_copy’:
CC drivers/media/platform/qcom/venus/firmware.o
drivers/media/usb/cx231xx/cx231xx-417.c:1389:11: error: implicit declaration of function ‘kmalloc’; did you mean ‘vmalloc’? [-Werror=implicit-function-declaration]
buffer = kmalloc(buffer_size, GFP_ATOMIC);
^~~~~~~
vmalloc
drivers/media/usb/cx231xx/cx231xx-417.c:1389:9: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
buffer = kmalloc(buffer_size, GFP_ATOMIC);
^
drivers/media/usb/cx231xx/cx231xx-417.c:1400:2: error: implicit declaration of function ‘kfree’; did you mean ‘vfree’? [-Werror=implicit-function-declaration]
kfree(buffer);
^~~~~
vfree
drivers/media/usb/cx231xx/cx231xx-417.c: In function ‘mpeg_open’:
drivers/media/usb/cx231xx/cx231xx-417.c:1713:7: error: implicit declaration of function ‘kzalloc’; did you mean ‘vzalloc’? [-Werror=implicit-function-declaration]
fh = kzalloc(sizeof(*fh), GFP_KERNEL);
^~~~~~~
vzalloc
drivers/media/usb/cx231xx/cx231xx-417.c:1713:5: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
fh = kzalloc(sizeof(*fh), GFP_KERNEL);
^
Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: i2c: tda1997: Fix an error handling path 'tda1997x_probe()'
If 'media_entity_pads_init()' fails, we must free the resources allocated
by 'v4l2_ctrl_handler_init()', as already done in the previous error
handling path.
Trivial fix to spelling mistake in dev_err message.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Brad Love [Tue, 8 May 2018 21:20:18 +0000 (17:20 -0400)]
media: cx23885: Ryzen DMA related RiSC engine stall fixes
This bug affects all of Hauppauge QuadHD boards when used on all Ryzen
platforms and some XEON platforms. On these platforms it is possible to
error out the RiSC engine and cause it to stall, whereafter the only
way to reset the board to a working state is to reboot.
Included is checks of the TC_REQ and TC_REQ_SET registers during states
of board initialization, reset, DMA start, and DMA stop. If both registers
are set, this indicates a stall in the RiSC engine, at which point the
bridge error is cleared.
A small delay is introduced in stop_dma as well, to allow transfers in
progress to finish.
After application all models work on Ryzen, occasionally yielding:
cx23885_clear_bridge_error: dma in progress detected 0x00000001 0x00000001, clearing
Signed-off-by: Brad Love <brad@nextdimension.cc> Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[hansverk@cisco.com: fix compiler warning of unused 'reg' variable] Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch loops up to five times on wakeup, marking any buffers
found done.
Since the count register is u16, but the vb2 counter is u32, some modulo
arithmetic is used to accommodate wraparound and ensure current active
buffer is the buffer expected.
Signed-off-by: Brad Love <brad@nextdimension.cc> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Thu, 3 May 2018 14:52:51 +0000 (10:52 -0400)]
media: v4l2-device.h: always expose mdev
The mdev field is only present if CONFIG_MEDIA_CONTROLLER is set.
But since we will need to pass the media_device to vb2 and the
control framework it is very convenient to just make this field
available all the time. If CONFIG_MEDIA_CONTROLLER is not set,
then it will just be NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sami Tolvanen [Tue, 8 May 2018 17:56:12 +0000 (13:56 -0400)]
media: v4l2-ioctl: replace IOCTL_INFO_STD with stub functions
This change removes IOCTL_INFO_STD and adds stub functions where
needed using the DEFINE_V4L_STUB_FUNC macro. This fixes indirect call
mismatches with Control-Flow Integrity, caused by calling standard
ioctls using a function pointer that doesn't match the function type.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Hans Verkuil <hansverk@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are two places pointing to an unexisting "m.chehab@kernel.org"
email. I never had such email, so, I'm unsure how it ends there.
Anyway, it is plain wrong.
While here, use my canonical e-mail on a bunch of places that
are pointing to another e-mail. The idea is that, from now on,
all places will be pointing to the same SMTP server.
* tag 'v4.17-rc4': (920 commits)
Linux 4.17-rc4
KVM: x86: remove APIC Timer periodic/oneshot spikes
genksyms: fix typo in parse.tab.{c,h} generation rules
kbuild: replace hardcoded bison in cmd_bison_h with $(YACC)
gcc-plugins: fix build condition of SANCOV plugin
MAINTAINERS: Update Kbuild entry with a few paths
Revert "usb: host: ehci: Use dma_pool_zalloc()"
platform/x86: Kconfig: Fix dell-laptop dependency chain.
platform/x86: asus-wireless: Fix NULL pointer dereference
arm64: vgic-v2: Fix proxying of cpuif access
KVM: arm/arm64: vgic_init: Cleanup reference to process_maintenance
KVM: arm64: Fix order of vcpu_write_sys_reg() arguments
MAINTAINERS & files: Canonize the e-mails I use at files
media: imx-media-csi: Fix inconsistent IS_ERR and PTR_ERR
tools: power/acpi, revert to LD = gcc
bdi: Fix oops in wb_workfn()
RDMA/cma: Do not query GID during QP state transition to RTR
IB/mlx4: Fix integer overflow when calculating optimal MTT size
IB/hfi1: Fix memory leak in exception path in get_irq_affinity()
IB/{hfi1, rdmavt}: Fix memory leak in hfi1_alloc_devdata() upon failure
...
qm1d1b0004: fix a warning about an unused default_cfg var
As warned by gcc:
drivers/media/tuners/qm1d1b0004.c:62:39: warning: 'default_cfg' defined but not used [-Wunused-const-variable=]
static const struct qm1d1b0004_config default_cfg = {
^~~~~~~~~~~
Sakari Ailus [Mon, 7 May 2018 12:41:58 +0000 (08:41 -0400)]
media: omap3isp: Don't use GFP_DMA
The isp stat driver allocates memory for DMA and uses GFP_DMA flag for
dev_alloc_coherent. The flag is no longer needed as the DMA mask is used
for the purpose. Remove it.
Sakari Ailus [Mon, 7 May 2018 12:37:48 +0000 (08:37 -0400)]
media: omap3isp: Remove useless NULL check in omap3isp_stat_config
The omap3isp driver checked whether the second argument (the new
configuration) to the ISP statistics is NULL. This is the pointer to the
user-given argument and is never NULL. Remove the check.
Reported-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com> Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: omap3isp: support 64-bit version of omap3isp_stat_data
C libraries with 64-bit time_t use an incompatible format for
struct omap3isp_stat_data. This changes the kernel code to
support either version, by moving over the normal handling
to the 64-bit variant, and adding compatiblity code to handle
the old binary format with the existing ioctl command code.
Fortunately, the command code includes the size of the structure,
so the difference gets handled automatically. In the process of
eliminating the references to 'struct timeval' from the kernel,
I also change the way the timestamp is generated internally,
basically by open-coding the v4l2_get_timestamp() call.
[Sakari Ailus: Alphabetical order of headers, clean up compat code]
Philipp Zabel [Thu, 3 May 2018 15:06:06 +0000 (11:06 -0400)]
media: imx: add 16-bit grayscale support
Since commit c8748e991fa0 ("gpu: ipu-csi: add 10/12-bit grayscale
support to mbus_code_to_bus_cfg") the IPU CSI can be configured to
capture 10-bit and 12-bit grayscale formats, expanded to 16-bit
grayscale, in bayer/generic data mode.
This patch adds support for V4L2_PIX_FMT_Y16 captured from sensors
that provide MEDIA_BUS_FMT_Y10_1X10 or MEDIA_BUS_FMT_Y12_1X12 data.
Cc: Jan Luebbe <jlu@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Acked-by: Steve Longerbeam <steve_longerbeam@mentor.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jasmin Jessich [Sun, 6 May 2018 10:44:22 +0000 (06:44 -0400)]
media: Use ktime_set() in pt1.c
In commit fdd7ec8fd29c a new variable ktime_t delay has been added.
We decided to use the API functions to initialize ktime_t variables
within media-tree. Thus variable delay needs to be initialized with
ktime_set() instead of setting it directly.
Julia Lawall [Sun, 6 May 2018 08:33:14 +0000 (04:33 -0400)]
media: pvrusb2: delete unneeded include
pvrusb2-video-v4l.h only declares pvr2_saa7115_subdev_update and
includes pvrusb2-hdw-internal.h. pvrusb2-cx2584x-v4l.c does not
use pvr2_saa7115_subdev_update and it explicitly includes
pvrusb2-hdw-internal.h.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Brad Love [Fri, 4 May 2018 21:53:35 +0000 (17:53 -0400)]
media: saa7164: Fix driver name in debug output
This issue was reported by a user who downloaded a corrupt saa7164
firmware, then went looking for a valid xc5000 firmware to fix the
error displayed...but the device in question has no xc5000, thus after
much effort, the wild goose chase eventually led to a support call.
The xc5000 has nothing to do with saa7164 (as far as I can tell),
so replace the string with saa7164 as well as give a meaningful
hint on the firmware mismatch.
Signed-off-by: Brad Love <brad@nextdimension.cc> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Jacopo Mondi [Fri, 4 May 2018 09:32:17 +0000 (05:32 -0400)]
media: renesas-ceu: Set mbus_fmt on subdev operations
The renesas-ceu driver intializes the desired mbus_format at 'complete'
time, inspecting the supported subdevice ones, and tuning some
parameters to produce the requested memory format from what the sensor
can produce. Although, the initially selected mbus_format was not
provided to the subdevice during set_fmt and try_fmt operations,
providing instead a '0' mbus format code.
As long as the sensor defaults to a compatible mbus_format when an
invalid code as '0' is provided, capture operations work correctly. If
the subdevice defaults to an unsupported format (eg. some RGB
permutations) capture does not work properly due to a mismatch on the
expected and received image format on the wire.
Fix that by re-using the initially selected mbus_format code during
set_fmt and try_fmt subdevice operation calls.
Tested by printing out the format selection procedure with ov7670
sensor.
With this patch applied:
[ 0.867015] ov7670_try_fmt_internal -- Looking for mbus_code 0x2008
[ 0.873205] ov7670_try_fmt_internal -- Try mbus_code 0x2008: match
Brad Love [Wed, 2 May 2018 21:46:18 +0000 (17:46 -0400)]
media: em28xx: Fix DualHD broken second tuner
The use of a hard coded i2c address breaks the creation of the
second tuner in DualHD 01595 models. The issue is compounded
by lack of any error message stating that a driver failed
initialization. Use addr, which contains the correct address
for each tuner.
Whilst the rationale for the above commit was in general correct, i.e.
that users *consuming* the DMA addresses should rely on sglen rather
than num_pages, it has always been the case that the DMA API itself
still requires that dma_{sync,unmap}_sg() are called with the original
number of entries as passed to dma_map_sg(), not the number of mapped
entries it returned. Thus the particular changes made in that patch
were erroneous.
At worst this might lead to data loss at the tail end of mapped buffers
on non-coherent hardware, while at best it's an example of incorrect
DMA API usage which has proven to mislead readers.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Trivial fix to spelling mistake in proc text string
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Fri, 27 Apr 2018 16:19:17 +0000 (12:19 -0400)]
media: coda: set colorimetry on coded queue
Do not set context colorimetry on the raw (OUTPUT) queue for encoders.
Always set colorimetry on the coded queue (CAPTURE for encoders, OUTPUT
for decoders).
This also skips propagation of capture queue format and selection
rectangle on S_FMT(OUTPUT) to the CAPTURE queue for encoders.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Fri, 27 Apr 2018 16:19:16 +0000 (12:19 -0400)]
media: coda: do not try to propagate format if capture queue busy
The driver helpfully resets the capture queue format and selection
rectangle whenever output format is changed. This only works while
the capture queue is not busy.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: sta2x11: Use gpio_is_valid() and remove unnecessary check
Replace the manual validity checks for the GPIO with the
gpio_is_valid().
In vip_gpio_reserve(), Error checking for gpio pin is not correct.
If pwr_pin = -1, It will return 0. This should be return an error.
In sta2x11_vip_init_one(), Error checking for gpio 'reset_pin'
is unnecessary. Because vip_gpio_reserve() is also checking for
valid gpio pin. So removed extra error checking for gpio 'reset_pin'.
Dan Carpenter [Fri, 20 Apr 2018 10:13:52 +0000 (06:13 -0400)]
media: vpbe_venc: potential uninitialized variable in ven_sub_dev_init()
Smatch complains that "venc" could be uninitialized. There are a couple
of error paths where it looks like maybe that could happen. I don't know
if it's really a bug, but it's reasonable to set "venc" to NULL and
silence the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Fri, 20 Apr 2018 08:13:53 +0000 (04:13 -0400)]
media: cec-gpio: use GPIOD_OUT_HIGH_OPEN_DRAIN
This driver needs a pull up output GPIO, but devm_gpiod_get() is called
with GPIOD_IN. This apparently works fine for the RPi3 where the DT
correctly specifies a pull up GPIO, but on the i.MX6 it also needs to
be specified with devm_gpiod_get().
Reported-by: Henrik Mau <Henrik.Mau@linn.co.uk> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
Reference id -> 668ff7502a9d ("mm: change return type to
vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>