vikram pandita [Sat, 12 Dec 2009 00:16:37 +0000 (16:16 -0800)]
omap: serial: fix non-empty uart fifo read abort
OMAP3xxx and OMAP4430 UART IP blocks have a restriction wrt RX FIFO.
Empty RX fifo read causes an abort.
OMAP3xxx:
UART IP revision >= 0x52 have this issue
MVR register format is:
Bits Field Name Description Type Reset
31:8 RESERVED RO 0x0
7:4 MAJOR Major revision number of the module. RO 0x--
3:0 MINOR Minor revision number of the module. RO 0x--
OMAP4xxx:
All revisions have this issue
Revision id check is not used as the format of MVR resigster has changed
For omap4 MVR register reads as: 0x50410602 => Revision id = 0x0602
Format of MVR register on omap4 is: (Courtesy: Cousson, Benoit)
Bits Field Name Description Type Reset
31:30 SCHEME Scheme revision number of module RO 0x1
29:28 RESERVED RO 0x1
27:16 FUNC Function revision number of module RO 0x041
15:11 RTL Rtl revision number of module RO 0x00
10:8 MAJOR Major revision number of the module. RO 0x6
7:6 CUSTOM Custom revision number of the module. RO 0x0
5:0 MINOR Minor revision number of the module. RO 0x02
Override the default 8250 read handler: mem_serial_in()
by a custom handler: serial_in_8250()
which makes sure that RX fifo is not read when empty
Cory Maccarrone [Sat, 12 Dec 2009 00:16:36 +0000 (16:16 -0800)]
omap1: htcherald: Update defconfig to include mux support
The existing htcherald_defconfig did not include mux support, which
prevented USB and other functionality from working out of the box.
This change updates the defconfig to add it in. It also aligns the
defconfig to the -rc8 kernel config.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
omap1: LCD_DMA: Use some define rather than a hexadecimal
The patch corrects the issue introduced with one of my earlier patches:
OMAP: DMA: Fix omapfb/lcdc on OMAP1510 broken when PM set[1]
as pointed out by OMAP subsystem maintainer.
Applies on top of my prevoius patch:
OMAP: DMA: move LCD DMA related code from plat-omap to mach-omap1[2]
Tested on Amstrad Delta
Compile tested with omap_generic_2420_defconfig
vikram pandita [Sat, 12 Dec 2009 00:16:36 +0000 (16:16 -0800)]
omap: header: remove unused data-type
Remove unused data type omap_gpio_switch_config
Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> Acked-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mika Westerberg [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
OMAP3: serial - allow platforms specify which UARTs to initialize
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Mike Rapoport [Sat, 12 Dec 2009 00:16:35 +0000 (16:16 -0800)]
omap3: cm-t35: add mux initialization
CM-T35 can be assembled with different set of peripherals thus making
certain interfaces available to user as GPIOs or dedicated pins. Because
of it CM-T35 bootloader sets up mux configuration only for pins
necessary to boot the system and the rest of the mux configuration is
done by the kernel. Besides, having mux configuration in the kernel
allows to minimize dependancy on bootloader.
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable minimum features to boot omap4430 on es1.0 samples. v2 versions
removes the "CONFIG_SYSFS_DEPRECATED_V2" since it's deprecated. Without
this older file system doesn't boot. One need to upgrade the filesystem
if getting stuck in first init function.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4: AuxCoreBoot registers only accessible in secure mode
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Pandora board file updates:
- change keycodes of game buttons
it was decided not to use ABXY layout by the developers.
- drop i2c bus 3 speed to 100kHz
this is needed for battery monitoring chip to work reliably.
- drop pandora_lcd platform_device
the older DSS driver was never functional on l-o or mainline
kernels due to missing panel driver, so remove unneeded
pandora_lcd platform_device. This also removes last OMAP_TAG
from the board file.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Cory Maccarrone [Sat, 12 Dec 2009 00:16:34 +0000 (16:16 -0800)]
omap1: Add omap7xx USB support
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
omap1: DMA: move LCD related code from plat-omap to mach-omap1
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Reviewed-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ladislav Michl [Sat, 12 Dec 2009 00:16:33 +0000 (16:16 -0800)]
omap1: Use gen_nand
Since omapnand driver never find its way into mainline, switch to gen_nand instead.
Following patch is compile tested only, but it is based on code I wrote for
NetStar board and runtime tested it there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Cc: Imre Deak <imre.deak@nokia.com> Cc: Brian Swetland <swetland@google.com> Cc: Kevin Hilman <kjh@hilman.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ladislav Michl [Sat, 12 Dec 2009 00:16:33 +0000 (16:16 -0800)]
smc91x: remove OMAP specific bits
Now that all OMAP boards are using the board resources, we don't need
to keep the arch/board specific crap in the driver header.
Cc: linux-net@vger.kernel.org Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Rajendra Nayak [Wed, 9 Dec 2009 01:47:17 +0000 (18:47 -0700)]
ARM: OMAP4: PM: Add init api for DPLL nodes
An api at init for all dpll nodes seem to be
needed to reparent the dpll clk node to its
bypass clk in case the dpll is in bypass.
If not done this causes sequencing issues at init
during propogate_rate.
Rajendra Nayak [Wed, 9 Dec 2009 01:47:16 +0000 (18:47 -0700)]
ARM: OMAP4: PM: Move DPLL control apis to dpll.c
This patch moves all the dpll control api's to a
common file dpll.c. This is in preperation of omap4
support wherein most of these api's can be reused.
Rajendra Nayak [Tue, 8 Dec 2009 18:31:44 +0000 (00:01 +0530)]
ARM: OMAP4: PM: Add dummy hooks for OMAP4 dpll api's
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Rajendra Nayak [Wed, 9 Dec 2009 01:46:28 +0000 (18:46 -0700)]
ARM: OMAP4: PM: OMAP4 clock tree and clkdev registration
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Rajendra Nayak [Wed, 9 Dec 2009 01:24:54 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Adds CM1/2 register field masks
This patch adds OMAP4 specific CM1 and CM2 module
register field masks. Auto generated using a python
script (gen_cm_shifts_and_mask.py) developed by Benoit
Cousson, Paul Walmsley and Rajendra Nayak.
Rajendra Nayak [Wed, 9 Dec 2009 01:24:52 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Adds PRM register shift and mask bits
This patch adds OMAP4 specific PRM register bit field
shifts and masks. Auto generated using a python script
(gen_prm_shifts_and_mask.py) developed by Benoit Cousson,
Paul Walmsley and Rajendra Nayak.
Rajendra Nayak [Wed, 9 Dec 2009 01:24:51 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Adds PRM register defs for OMAP4
This patch adds OMAP4 specific PRM register defs. Auto generated
using a python script (gen_prm_4430_h.py) developed by Paul
Walmsley and Benoit Cousson.
Rajendra Nayak [Wed, 9 Dec 2009 01:24:50 +0000 (18:24 -0700)]
ARM: OMAP4: PM: Adds CM1/2 register defs for OMAP4
This patch adds OMAP4 specific CM1 and CM2 module
register defs. Autogenerated using a python scripts
(gen_cm1_4430_h.py,gen_cm2_4430_h.py) developed
by Paul Walmsley and Benoit Cousson.
Rajendra Nayak [Wed, 9 Dec 2009 01:24:49 +0000 (18:24 -0700)]
ARM: OMAP4: PM: PRM/CM module offsets for OMAP4
This patch adds the offsets for new modules in PRM
and CM for OMAP4
These are autogenerated using a python script (gen_prcm44xx_h.py)
developed by Paul Walmsley and Benoit Cousson.
Kevin Hilman [Tue, 8 Dec 2009 23:34:23 +0000 (16:34 -0700)]
OMAP: omap_device: use read_persistent_clock() instead of getnstimeofday()
During suspend and resume, when omap_device deactivation and
activation is happening, the timekeeping subsystem has likely already
been suspended. Thus getnstimeofday() will fail and trigger a WARN().
Use read_persistent_clock() instead of getnstimeofday() to avoid this.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Tue, 8 Dec 2009 23:34:17 +0000 (16:34 -0700)]
OMAP3 hwmod: drop most of the OCP_SYSCONFIG.CLOCKACTIVITY code
Earlier, the hwmod code had considered the OCP_SYSCONFIG.CLOCKACTIVITY
bits to be incremental power saving bits, controlling internal IP
block clock gates. This was a misapprehension. The CLOCKACTIVITY
bits are used to indicate, in advance, which clocks will be cut when
the module acknowledges an idle request. This enables the IP block to
take whatever action is necessary to complete any in-progress work
before asserting its IdleAck.
In the current Linux-OMAP code, this implies that the clock framework
should be changing module CLOCKACTIVITY bits as module clocks are enabled
and disabled. We don't do that yet, but in the future, we should.
This must wait until the clock tree is annotated with omap_hwmod pointers
(or vice-versa). In the meantime, drop most of the hwmod code that
controls CLOCKACTIVITY bits to avoid confusion.
This patch has benefited from many illuminating discussions with (in
alphabetical order) Benoît Cousson <b-cousson@ti.com>, Rajendra Nayak
<rnayak@ti.com>, and Sebastien Sabatier <s-sabatier1@ti.com>.
Paul Walmsley [Tue, 8 Dec 2009 23:34:16 +0000 (16:34 -0700)]
OMAP hwmod: add names to module MPU IRQ lines
Replace the existing u8 array of module MPU IRQ lines with a struct
that includes a name - similar to the existing struct
omap_hwmod_dma_info. Device drivers can then use
platform_get_resource_byname() to retrieve specific IRQs without nasty
dependencies on array ordering.
Thanks to Benoît Cousson <b-cousson@ti.com> and Kevin Hilman
<khilman@deeprootsystems.com> for feedback on this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com>
This patch fills in the OCP_SYSCONFIG.AUTOIDLE handling in the OMAP
hwmod code.
After this patch, the hwmod code will set the module AUTOIDLE bit
(generally <module>.OCP_SYSCONFIG.AUTOIDLE) to 1 by default upon
enable. If the hwmod flag HWMOD_NO_OCP_AUTOIDLE is set, AUTOIDLE will
be set to 0 upon enable. Upon module disable, AUTOIDLE will be set to
1.
Enabling module autoidle should save some power. The only reason to
not set the OCP_SYSCONFIG.AUTOIDLE bit is if there is a bug in the
module RTL, e.g., the MPUINTC block on OMAP3.
Comments from Kevin Hilman <khilman@deeprootsystems.com> inspired this patch,
and Kevin tested an earlier version of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley [Tue, 8 Dec 2009 23:34:14 +0000 (16:34 -0700)]
OMAP3 hwmod: reprogram OCP_SYSCONFIG register after setting SOFTRESET
Reprogram the module's OCP_SYSCONFIG register after module reset (SOFTRESET
= 1). This may not be needed, but the definition of the reset performed by
the SOFTRESET bit is unclear.
Kevin Hilman <khilman@deeprootsystems.com> tested an earlier version of
this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Paul Walmsley [Tue, 8 Dec 2009 23:33:16 +0000 (16:33 -0700)]
OMAP clock/hwmod: fix off-by-one errors
Fix loop bailout off-by-one bugs reported by Juha Leppänen
<juha_motorsportcom@luukku.com>.
This second version incorporates comments from Russell King
<linux@arm.linux.org.uk>. A new macro, 'omap_test_timeout', has
been created, with cleaner code, and existing code has been converted
to use it.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Juha Leppänen <juha_motorsportcom@luukku.com> Cc: Russell King <linux@arm.linux.org.uk>
Paul Walmsley [Tue, 8 Dec 2009 23:33:14 +0000 (16:33 -0700)]
OMAP3: SDRC: Place SDRC AC timing and MR changes in CORE DVFS SRAM code behind Kconfig
The code that reprograms the SDRC memory controller during CORE DVFS,
mach-omap2/sram34xx.S:omap3_sram_configure_core_dpll(), does not
ensure that all L3 initiators are prevented from accessing the SDRAM
before modifying the SDRC AC timing and MR registers. This can cause
memory to be corrupted or cause the SDRC to enter an unpredictable
state. This patch places that code behind a Kconfig option,
CONFIG_OMAP3_SDRC_AC_TIMING for now, and adds a note explaining what
is going on. Ideally the code can be added back in once supporting
code is present to ensure that other initiators aren't touching the
SDRAM. At the very least, these registers should be reprogrammable
during kernel init to deal with buggy bootloaders. Users who know
that all other system initiators will not be touching the SDRAM can
also re-enable this Kconfig option.
This is a modification of a patch originally written by Rajendra Nayak
<rnayak@ti.com> (the original is at http://patchwork.kernel.org/patch/51927/).
Rather than removing the code completely, this patch just comments it out.
Thanks to Benoît Cousson <b-cousson@ti.com> and Christophe Sucur
<c-sucur@ti.com> for explaining the technical basis for this and for
explaining what can be done to make this path work in future code.
Thanks to Richard Woodruff <r-woodruff2@ti.com>, Nishanth Menon
<nm@ti.com>, and Olof Johansson <olof@lixom.net> for their comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Rajendra Nayak <rnayak@ti.com> Cc: Christophe Sucur <c-sucur@ti.com> Cc: Benoît Cousson <b-cousson@ti.com> Cc: Richard Woodruff <r-woodruff2@ti.com> Cc: Nishanth Menon <nm@ti.com> Cc: Olof Johansson <olof@lixom.net>
Paul Walmsley [Tue, 8 Dec 2009 23:33:11 +0000 (16:33 -0700)]
OMAP clockdomain/powerdomain: optimize out sleepdep code on OMAP24xx
OMAP24xx chips don't support software-configurable sleep dependencies.
Test early for this so the compiler can redact the entire function body
on OMAP24xx.
Avoid cluttering the Kconfig space with debug options that are rarely
used. These can now be enabled and disabled by patching the "#undef DEBUG"
in the source files with "#define DEBUG", conforming to the practice for
the rest of the linux-omap code.
Also, while we're here, some lines in plat-omap/Kconfig use sets of
leading spaces when those lines should start with tabs. Convert most
of them to use tabs.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com>
Device drivers and loadable modules should not be calling these
prm_* and cm_* functions, so stop exporting them. Only core code
and device driver integration code (in arch/arm/*omap*) should
call these functions.
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the mpu_rate data structures out into their own
files, opp.h and opp_data.c. In the long run, these mpu_rate tables
should be replaced with OPP code.
Also includes a patch from Felipe Balbi <felipe.balbi@nokia.com> to
mark omap1_clk_functions as __initdata to avoid a section warning:
http://patchwork.kernel.org/patch/64366/
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Felipe Balbi <felipe.balbi@nokia.com> Cc: Nishanth Menon <nm@ti.com>
Paul Walmsley [Tue, 8 Dec 2009 23:29:37 +0000 (16:29 -0700)]
OMAP1 clock: convert test in disable_unused() to use ENABLE_ON_INIT
mach-omap1/clock.c:omap1_clk_disable_unused() contains a test that
assumes that the clock structures are available in the file's
namespace. After a following patch, this will no longer be the case.
So we need to reimplement that test. It turns out that we already
have a facility in the clock framework to handle this case - the
ENABLE_ON_INIT flag - used on OMAP2/3. Remove the offending test and
mark the clocks that it was intended to catch as ENABLE_ON_INIT.
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the prcm_config data structures out into their own
files, opp2xxx.h and opp24{2,3}0_data.c, and only build in the OPP tables
for the target device. This should save some memory. In the long run,
these prcm_config tables should be replaced with OPP code.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Richard Woodruff <r-woodruff2@ti.com> Cc: Nishanth Menon <nm@ti.com>
Paul Walmsley [Tue, 8 Dec 2009 23:18:47 +0000 (16:18 -0700)]
OMAP2xxx clock: remove implicit dependency between rate CPU flag and clkdev_omap CPU flag
cpu_mask is reused in the OMAP2xxx clock code to match against both the
CPU-specific rate flags (e.g., RATE_IN_2420) and the OMAP clkdev integration
code CPU flags (e.g., CK_242X). This means that any patch that renumbers the
CK_* macros, as the next patch does, will probably break. This patch
separates the clkdev_omap and clksel_rate CPU type detection flags so
the CK_* macros can be renumbered freely.
Paul Walmsley [Tue, 8 Dec 2009 23:18:46 +0000 (16:18 -0700)]
OMAP2 clock: APLL code shouldn't rely on static clocks in its local namespace
Similar to the previous patch, the APLL code relied on the presence of the
static struct clks in its own namespace. The APLL code didn't use them for
validation, however - it adjusted its own internal state depending on
the struct clk * that called it. Now that static struct clks are
leaving the clock24xx.c namespace, use a more durable method: split the
omap2_clk_fixed_enable() function into omap2_clk_apll96_enable() and
omap2_clk_apll54_enable(). They still share a disable function.
Paul Walmsley [Tue, 8 Dec 2009 23:18:44 +0000 (16:18 -0700)]
OMAP1/2/3 clock: remove paranoid checks in preparation for clock{,2xxx,3xxx}_data.c
Some parts of the clock code took advantage of the fact that the statically
allocated clock tree was in clock{,24xx,34xx}.c's local namespace to do some
extra argument checks. These are overzealous and are more difficult to
maintain when the clock tree is in a separate namespace, so, remove them.
Linus Torvalds [Thu, 10 Dec 2009 17:35:02 +0000 (09:35 -0800)]
Merge branch 'bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
* 'bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: try harder to balloon up under memory pressure.
Xen balloon: fix totalram_pages counting.
xen: explicitly create/destroy stop_machine workqueues outside suspend/resume region.
xen: improve error handling in do_suspend.
xen: don't leak IRQs over suspend/resume.
xen: call clock resume notifier on all CPUs
xen: use iret for return from 64b kernel to 32b usermode
xen: don't call dpm_resume_noirq() with interrupts disabled.
xen: register runstate info for boot CPU early
xen: register runstate on secondary CPUs
xen: register timer interrupt with IRQF_TIMER
xen: correctly restore pfn_to_mfn_list_list after resume
xen: restore runstate_info even if !have_vcpu_info_placement
xen: re-register runstate area earlier on resume.
xen: wait up to 5 minutes for device connetion
xen: improvement to wait_for_devices()
xen: fix is_disconnected_device/exists_disconnected_device
xen/xenbus: make DEVICE_ATTR()s static
Linus Torvalds [Thu, 10 Dec 2009 17:34:40 +0000 (09:34 -0800)]
Merge branch 'xen/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen
* 'xen/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen pvfb: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
fb-defio: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
fb-defio: If FBINFO_VIRTFB is defined, do not set VM_IO flag.
Fix toogle whether xenbus driver should be built as module or part of kernel.
Linus Torvalds [Thu, 10 Dec 2009 17:33:29 +0000 (09:33 -0800)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (47 commits)
ext4: Fix potential fiemap deadlock (mmap_sem vs. i_data_sem)
ext4: Do not override ext2 or ext3 if built they are built as modules
jbd2: Export jbd2_log_start_commit to fix ext4 build
ext4: Fix insufficient checks in EXT4_IOC_MOVE_EXT
ext4: Wait for proper transaction commit on fsync
ext4: fix incorrect block reservation on quota transfer.
ext4: quota macros cleanup
ext4: ext4_get_reserved_space() must return bytes instead of blocks
ext4: remove blocks from inode prealloc list on failure
ext4: wait for log to commit when umounting
ext4: Avoid data / filesystem corruption when write fails to copy data
ext4: Use ext4 file system driver for ext2/ext3 file system mounts
ext4: Return the PTR_ERR of the correct pointer in setup_new_group_blocks()
jbd2: Add ENOMEM checking in and for jbd2_journal_write_metadata_buffer()
ext4: remove unused parameter wbc from __ext4_journalled_writepage()
ext4: remove encountered_congestion trace
ext4: move_extent_per_page() cleanup
ext4: initialize moved_len before calling ext4_move_extents()
ext4: Fix double-free of blocks with EXT4_IOC_MOVE_EXT
ext4: use ext4_data_block_valid() in ext4_free_blocks()
...
Linus Torvalds [Thu, 10 Dec 2009 17:32:24 +0000 (09:32 -0800)]
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
exofs: Multi-device mirror support
exofs: Move all operations to an io_engine
exofs: move osd.c to ios.c
exofs: statfs blocks is sectors not FS blocks
exofs: Prints on mount and unmout
exofs: refactor exofs_i_info initialization into common helper
exofs: dbg-print less
exofs: More sane debug print
trivial: some small fixes in exofs documentation
David Wong [Thu, 3 Dec 2009 13:54:25 +0000 (10:54 -0300)]
V4L/DVB (13592): max2165: 32bit build patch
This patch drops usage of floating point variable for 32bit build
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Boaz Harrosh [Mon, 16 Nov 2009 14:03:05 +0000 (16:03 +0200)]
exofs: Multi-device mirror support
This patch changes on-disk format, it is accompanied with a parallel
patch to mkfs.exofs that enables multi-device capabilities.
After this patch, old exofs will refuse to mount a new formatted FS and
new exofs will refuse an old format. This is done by moving the magic
field offset inside the FSCB. A new FSCB *version* field was added. In
the future, exofs will refuse to mount unmatched FSCB version. To
up-grade or down-grade an exofs one must use mkfs.exofs --upgrade option
before mounting.
Introduced, a new object that contains a *device-table*. This object
contains the default *data-map* and a linear array of devices
information, which identifies the devices used in the filesystem. This
object is only written to offline by mkfs.exofs. This is why it is kept
separate from the FSCB, since the later is written to while mounted.
Same partition number, same object number is used on all devices only
the device varies.
* define the new format, then load the device table on mount time make
sure every thing is supported.
* Change I/O engine to now support Mirror IO, .i.e write same data
to multiple devices, read from a random device to spread the
read-load from multiple clients (TODO: stripe read)
Implementation notes:
A few points introduced in previous patch should be mentioned here:
* Special care was made so absolutlly all operation that have any chance
of failing are done before any osd-request is executed. This is to
minimize the need for a data consistency recovery, to only real IO
errors.
* Each IO state has a kref. It starts at 1, any osd-request executed
will increment the kref, finally when all are executed the first ref
is dropped. At IO-done, each request completion decrements the kref,
the last one to return executes the internal _last_io() routine.
_last_io() will call the registered io_state_done. On sync mode a
caller does not supply a done method, indicating a synchronous
request, the caller is put to sleep and a special io_state_done is
registered that will awaken the caller. Though also in sync mode all
operations are executed in parallel.
Boaz Harrosh [Sun, 8 Nov 2009 12:54:08 +0000 (14:54 +0200)]
exofs: Move all operations to an io_engine
In anticipation for multi-device operations, we separate osd operations
into an abstract I/O API. Currently only one device is used but later
when adding more devices, we will drive all devices in parallel according
to a "data_map" that describes how data is arranged on multiple devices.
The file system level operates, like before, as if there is one object
(inode-number) and an i_size. The io engine will split this to the same
object-number but on multiple device.
At first we introduce Mirror (raid 1) layout. But at the final outcome
we intend to fully implement the pNFS-Objects data-map, including
raid 0,4,5,6 over mirrored devices, over multiple device-groups. And
more. See: http://tools.ietf.org/html/draft-ietf-nfsv4-pnfs-obj-12
* Define an io_state based API for accessing osd storage devices
in an abstract way.
Usage:
First a caller allocates an io state with:
exofs_get_io_state(struct exofs_sb_info *sbi,
struct exofs_io_state** ios);
And when done
exofs_put_io_state(struct exofs_io_state *ios);
* Convert all source files to use this new API
* Convert from bio_alloc to bio_kmalloc
* In io engine we make use of the now fixed osd_req_decode_sense
There are no functional changes or on disk additions after this patch.
Boaz Harrosh [Tue, 3 Nov 2009 14:46:00 +0000 (16:46 +0200)]
exofs: move osd.c to ios.c
If I do a "git mv" together with a massive code change
and commit in one patch, git looses the rename and
records a delete/new instead. This is bad because I want
a rename recorded so later rebased/cherry-picked patches
to the old name will work. Also the --follow is lost.
Linus Torvalds [Thu, 10 Dec 2009 03:57:06 +0000 (19:57 -0800)]
Merge branch 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: Update version to 20091112.
ACPICA: Add additional module-level code support
ACPICA: Deploy new create integer interface where appropriate
ACPICA: New internal utility function to create Integer objects
ACPICA: Add repair for predefined methods that must return sorted lists
ACPICA: Fix possible fault if return Package objects contain NULL elements
ACPICA: Add post-order callback to acpi_walk_namespace
ACPICA: Change package length error message to an info message
ACPICA: Reduce severity of predefined repair messages, Warning to Info
ACPICA: Update version to 20091013
ACPICA: Fix possible memory leak for Scope ASL operator
ACPICA: Remove possibility of executing _REG methods twice
ACPICA: Add repair for bad _MAT buffers
ACPICA: Add repair for bad _BIF/_BIX packages
Linus Torvalds [Thu, 10 Dec 2009 03:53:11 +0000 (19:53 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (41 commits)
hwmon: (adt7475) Add VID support for the ADT7476
hwmon: (adt7475) Add an entry in MAINTAINERS
hwmon: (adt7475) Add support for the ADT7476
hwmon: (adt7475) Voltage attenuators can be bypassed
hwmon: (adt7475) Print device information on probe
hwmon: (adt7475) Handle alternative pin functions
hwmon: (adt7475) Move sysfs files removal to a separate function
hwmon: (adt7475) Add support for the ADT7490
hwmon: (adt7475) Improve device detection
hwmon: (adt7475) Add missing static marker
hwmon: (adt7475) Rework voltage inputs handling
hwmon: (adt7475) Implement pwm_use_point2_pwm_at_crit
hwmon: (adt7475) New documentation
hwmon: (adt7475) Add support for the ADT7473
hwmon: (f71882fg) Add support for the f71889fg (version 2)
hwmon: (f71882fg) Fix sysfs file removal
hwmon: (f71882fg) Cleanup sysfs attr creation 2/2
hwmon: (f71882fg) Cleanup sysfs attr creation 1/2
hwmon: (thmc50) Stop using I2C_CLIENT_MODULE_PARM
hwmon: Add Freescale MC13783 ADC driver
...
Linus Torvalds [Thu, 10 Dec 2009 03:52:01 +0000 (19:52 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
Linus Torvalds [Thu, 10 Dec 2009 03:46:12 +0000 (19:46 -0800)]
Merge branch 'next-i2c' of git://git.fluff.org/bjdooks/linux
* 'next-i2c' of git://git.fluff.org/bjdooks/linux: (25 commits)
i2c-pnx: Map I2C adapter number to platform ID number
i2c-omap: OMAP3: PM: (re)init for every transfer to support off-mode
i2c-designware: i2c_dw_handle_tx_abort: Use dev_dbg() for NOACK cases
i2c-designware: Cosmetic cleanups
i2c-designware: Tx abort cleanups
i2c-designware: Skip RX_FULL and TX_EMPTY bits on tx abort errors
i2c-designware: i2c_dw_xfer_msg: Fix error handling procedures
i2c-designware: Disable TX_EMPTY when all i2c_msg msgs has been processed
i2c-designware: Process all i2c_msg messages in the interrupt handler
i2c-designware: i2c_dw_read: Remove redundant target address checker
i2c-designware: i2c_dw_func: Set I2C_FUNC_SMBUS_foo bits
i2c-designware: Initialize byte count variables just prior to being used
i2c-designware: i2c_dw_xfer_msg: Introduce a local "buf" pointer
i2c-designware: Divide i2c_dw_xfer_msg into two functions
i2c-designware: Enable RX_FULL interrupt
i2c-designware: Set Tx/Rx FIFO threshold levels
i2c-designware: Process i2c_msg messages in the interrupt handler
i2c-designware: i2c_dw_xfer_msg: Fix i2c_msg search bug
i2c-designware: Improved _HCNT/_LCNT calculation
i2c-designware: Remove an useless local variable "num"
...
Linus Torvalds [Thu, 10 Dec 2009 03:45:58 +0000 (19:45 -0800)]
Merge branch 's3c24xx-updates' of git://git.fluff.org/bjdooks/linux
* 's3c24xx-updates' of git://git.fluff.org/bjdooks/linux:
ARM: S3C24XX: DMA: Use valid index when accessing array
ARM: S3C: move s3c_pwm_remove to .devexit.text
ARM: S3C24XX: Export s3c24xx_set_fiq for modules.
ARM: S3C: move s3c_adc_remove to .devexit.text