Alex Kiernan [Wed, 11 Mar 2020 08:46:29 +0000 (08:46 +0000)]
cmd: gpio: Make `gpio input` return pin value again
a8f4e9f5cf39 ("cmd: gpio: Correct do_gpio() return value") correctly
changed the behaviour of the gpio command to return CMD_RET_SUCCESS or
CMD_RET_FAILURE, but any existing script which expects the return value
to be the pin value is broken by this change.
Reinstate the legacy behaviour for `gpio input` only.
Fixes: a8f4e9f5cf39 ("cmd: gpio: Correct do_gpio() return value") Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Signed-off-by: Alex Kiernan <alex.kiernan@hivehome.com> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Tue, 10 Mar 2020 00:20:43 +0000 (09:20 +0900)]
Makefile: doesn't need check stack size when dtb is not built
The commit 427d00c64417 ("Makefile: ensure DTB doesn't overflow into
initial stack") adds an extra check for stack size in BSS if
CONFIG_SYS_INIT_SP_BSS_OFFSET is enabled.
This check, however, doesn't make sense under the configuration where
control dtb won't be built in and it should be void in such cases.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Fixes: 427d00c64417 ("Makefile: ensure DTB doesn't overflow into initial stack") Reviewed-by: Stephen Warren <swarren@nvidia.com>
Actually, using dev->seq value before probe to deduce the current
serial port index leads to reading an invalid seq value (-1).
So, getting dev->seq at probe time.
Tom Rini [Thu, 12 Mar 2020 16:51:44 +0000 (12:51 -0400)]
Merge tag 'efi-2020-04-rc4-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4 (3)
This pull request provides the hardware RNG driver for Amlogic systems needed
for the EFI_RNG_PROTOCOL.
Furthermore bug fixes are provided:
* correct an error message in the efidebug command
* correct an error in the 'efidebug rm' command
* remove an unnecessary assignment in efi_queue_event()
For all sandbox systems with DM_RNG we enable RNG_SANDBOX. So we can simply
set the default to yes.
All rng drivers depend on DM_RNG. Use a single 'if' instead of individual
dependencies. Now 'make menuconfig' shows the individual drivers neatly
indented under the DM_RNG entry.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
AKASHI Takahiro [Fri, 28 Feb 2020 00:05:04 +0000 (09:05 +0900)]
cmd: efidebug: fix a failure of "boot rm" sub-command
There is a wrong usage of utf8_utf16_strncpy() in "boot rm" command, and
then it will end up with a failure of this command due to a wrong
value of an interim variable ("var_name16").
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Wed, 11 Mar 2020 06:18:18 +0000 (15:18 +0900)]
efi_loader: get_memory_map: return parameters whenever possible
Currently, if GetMemoryMap API returns EFI_BUFFER_TOO_SMALL, it doesn't
set valid values to other parameters, descriptor_size and
descriptor_version, except memory_map_size.
Some efi applications, however, may use those value; in particular,
xen uses descriptor_size to calculate a size of buffer to be allocated.
While UEFI specification is ambiguous in this point, it would be better
to address this issue proactively to maximize the compatibility with
existing efi applications.
With this patch, for example, xen.efi (and hence linux kernel) can be
started via bootefi without modification.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Sam Shih [Wed, 4 Mar 2020 12:03:48 +0000 (20:03 +0800)]
arm: mediatek: remove unused binman config
The binman-option BINMAN_FDT is introduced by this commit:
commit 2b6c644e9e18 ("binman: Add a library to access binman entries")
BINMAN_FDT being selected when BINMAN=y that resulting in mt7623
and mt7622 are unable to boot. The root cause of this issue is commit:
commit a599fe241181 ("arm: MediaTek: add basic support for MT7629 boards")
select BINMAN=y in all mediatek SoCs, and others mediatek SoCs not
expect to use BINMAN_FDT.
This patch remove BINMAN=y option when ARCH_MEDIATEK=y and
move this to the specify SoCs part config.
Signed-off-by: Sam Shih <sam.shih@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de>
Currently when booting the kernel on i.MX8 U-Boot hangs in an
endless loop when switching off dma, connectivity or lsio power
domains during device removal. It hapens first when removing
gpio0 (gpio@5d080000) device, here its power domain device
'lsio_gpio0' is obtained for switching off power. Since the
obtained 'lsio_gpio0' device is removed afterwards, its power
domain is also switched off and here the parent power domain
device 'lsio_power_domain' is optained for switching off the
power. Thereafter, when the obtained 'lsio_power_domain' is
removed, device_remove() removes its first child 'lsio_gpio0'.
During this child removal the 'lsio_power_domain' device is
obtained again for switching and when removing it later,
the same child removal is repeated, so we are stuck in an
endless loop. Below is a snippet from dm tree on i.MX8QXP
for better illustration of the DM devices relationship:
Patrick Delaunay [Tue, 10 Mar 2020 15:05:43 +0000 (16:05 +0100)]
stm32mp: update dependency for STM32_ETZPC
Correct the dependency for STM32 ETZPC protection, linked to SOC
STM32MP identified by CONFIG_STM32MP15x and not linked to
CONFIG_TARGET_STM32MP1 (no more existing).
This patch fix an issue introduced by commit 9ab25759e1e7 ("stm32mp1:
split board and SOC support for STM32MP15x family").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
Pedro Jardim [Thu, 13 Feb 2020 12:25:32 +0000 (09:25 -0300)]
mx6slevk: Convert to DM_ETH
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Pedro Jardim [Thu, 13 Feb 2020 17:59:43 +0000 (14:59 -0300)]
mx6sabreauto: Convert to DM_ETH
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Alifer Moraes [Fri, 14 Feb 2020 19:18:50 +0000 (16:18 -0300)]
arm: dts: imx8mq-evk: add phy-reset-gpios for fec1
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Alifer Moraes [Mon, 10 Feb 2020 14:28:01 +0000 (11:28 -0300)]
mx6sabresd: Convert ethernet to driver model
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Fabien Lehoussel [Mon, 24 Feb 2020 15:45:31 +0000 (16:45 +0100)]
board: sama5d3_xplained: Fix uboot size when loaded from NAND by SPL
Uboot size is incorrect.
Uboot SPL use CONFIG_SYS_MONITOR_LEN to read uboot from NAND : 0x80000
With sama5d3_xplained_nandflash_defconfig : u-boot.bin size is ~800Ko 0xC0000
Clemens Gruber [Mon, 24 Feb 2020 19:52:20 +0000 (20:52 +0100)]
net: phy: marvell: Unify 88E151x series phy_driver
The PHY models of the Marvell 88E151x series are not reliably
distinguishable by their uid / PHY identifiers.
The 88E1510, 88E1512, 88E1514 and 88E1518 all have the same OUI and
model number and bits 3:0 in the PHY Identifier 2 (Page 0, Reg 3) are
described as HW revision number, but both 88E1510 and 88E1518 PHYs were
observed with the same HW rev number (1).
Before commit eda8441ada77 ("net: phy: Fix mask so that we can identify
Marvell 88E1518"), the 88E151x were detected because the HW revision
bits were masked from the uid. After that change, 88E1510/12/18 were all
detected as 88E1518 and the 88E1510 specific code was no longer run.
I modified the mask to again ignore all four HW revision bits, removed
the 88E1510 specific code (board-specific LED/INTn setup), which was not
called since late 2016 anyway and renamed the config function and
phy_driver struct to the better fitting 88e151x.
The uid and mask bits 3:0 are now again the same as in the Linux kernel.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Michal Simek [Tue, 18 Feb 2020 12:51:02 +0000 (13:51 +0100)]
net: phy: dp83867: Add SGMII mode type switching
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Patch description, dt flags have been done in mainline Linux by
commit a2111c460c0c ("net: phy: dp83867: Add documentation for SGMII mode type")
and by commit 507ddd5c0d47 ("net: phy: dp83867: Add SGMII mode type switching")
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michal Simek [Mon, 17 Feb 2020 09:38:57 +0000 (10:38 +0100)]
dt-bindings: net: dp83867: Remove binding doc from U-Boot tree
U-Boot is having DT which doesn't cover all options currently supported by
driver. DT binding is aligned with Linux kernel version available here.
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ti,dp83867.txt
Based on my talk with Grygorii Strashko better will be to remove it.
Also Linux kernel bindings are being converted to yaml that's another
reason to do it only at one place.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Alex Marginean [Thu, 9 Jan 2020 08:50:05 +0000 (10:50 +0200)]
net: phy: add XFI, USXGMII types to is_10g_interface() helper
The helper is used to reset PHYs on connect and it determines the clause
to use (C22/C45) based on interface type. This fixes 'PHY reset timed out'
warnings in console for USXGMII/XFI PHYs.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andre Przywara [Fri, 3 Jan 2020 22:08:47 +0000 (22:08 +0000)]
net: phy: Fix overlong PHY timeout
Commit 038ea7521a45 ("net: phy: Increase link up delay in
genphy_update_link()") increased the per-iteration waiting time from
1ms to 50ms, without adjusting the timeout counter. This lead to the
timeout increasing from the typical 4 seconds to over three minutes.
Adjust the timeout counter evaluation by that factor of 50 to bring the
timeout back to the intended value.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Fixes: net: phy: Increase link up delay in genphy_update_link() ("038ea7521a45") Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Matthias Brugger <mbrugger@suse.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andre Przywara [Mon, 25 Nov 2019 01:32:15 +0000 (01:32 +0000)]
doc: net: Rewrite network driver documentation
doc/README.drivers.eth seems like a good source for understanding
U-Boot's network subsystem, but is only talking about legacy network
drivers. This is particularly sad as proper documentation would help in
porting drivers over to the driver model.
Rewrite the document to describe network drivers in the new driver model
world. Most driver callbacks/methods are almost identical in their
semantic, but recv() differs in some important details.
Also keep some parts of the original text at the end, to help
understanding old drivers. Add some hints on how to port drivers over.
This also uses the opportunity to reformat the document in reST, on the
way moving it into doc/driver-model and adding it into the structure
there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Wed, 4 Dec 2019 13:32:15 +0000 (15:32 +0200)]
drivers: net: phy: aquantia: drop XGMII as a valid system interface proto
Use either USXGMII or XFI in aquantia_set_proto and drop XGMII as a valid
protocol configuration. The PHY doesn't support it, it's just used as an
alias for one of the other two protocols.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add NC-SI to the usual phy handling. This makes two notable changes:
- Somewhat similar to a fixed phy, phy_connect() will create an NC-SI
phy if CONFIG_PHY_NCSI is defined.
- An early return is added to phy_read() and phy_write() to handle a
case like the NC-SI phy which does not define a bus.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.
NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).
This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).
The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Mon, 9 Mar 2020 17:01:57 +0000 (13:01 -0400)]
Azure/Travis: Re-sync jobs and clarify exclusions
We keep both of these jobs in sync as much as possible even when the
primary motivation is to keep Travis from exceeding the build time limit
there. With that in mind:
- Use "rk" not "rockchip" to get all Rockchip SoC platforms in one job,
rather than just all Rockchip vendor platforms.
- The NXP LX216* SoCs have their own job, exclude them from the AArch64
generic job.
- SoCFPGA SoCs have their own job, exclude them from the AArch64 generic
job.
Giulio Benetti [Fri, 31 Jan 2020 13:39:47 +0000 (14:39 +0100)]
serial_lpuart: make clock failure less verbose
Some device may enable CONFIG_CLK but not still support this clock in
CC, so better use debug() in place of dev_warn() otherwise a lot of
boards will throw useless dev_warn()s.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Simon Glass <sjg@chromium.org>
imx8mm/mn: Add missing root clock entry for ARM core clock
The current implementation in arch/arm/mach-imx/cpu.c uses non-DM
code to retrieve the core clock frequency. As the root clock is not
listed we currently get:
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Fix this by adding the missing entry, which results in:
Baruch Siach [Tue, 4 Feb 2020 16:57:08 +0000 (18:57 +0200)]
mx6cuboxi: don't disable fdt relocation
fdt_high value of 0xffffffff disables fdt relocation on boot. We don't
need that for Cubox-i/Hummingboard. Rely on generic code to find the
optimal fdt location at boot time.
, which causes the console to not show characters after the LPUART driver
is probed as the 'baudrate' variable is not properly translated.
Fix it by splitting the console variable in two parts: one for the
ttyLP0 part and the other one for the baudrate, which matches the way
it is done on other i.MX targets.
Tested by successfully booting a mainline kernel on a i.MX8QXP MEK
board.
Heiko Schocher [Mon, 2 Mar 2020 08:44:03 +0000 (09:44 +0100)]
imx6, aristainetos2c: add da9063 pmic setup
On the aristainetos2c boards the PMIC needs to be initialized,
because the Ethernet PHY uses a different regulator that is not
setup per hardware default. This does not influence the other
versions as this regulator isn't used there at all.
Faiz Abbas [Wed, 26 Feb 2020 08:14:37 +0000 (13:44 +0530)]
arm: dts: k3-j721e-r5-common-proc-board: Use unique names for dummy clocks
Update the dummy clock names to use unique identifiers. Otherwise the
previous node just gets overwitten by the next one with the same name.
This fixes eMMC boot not working on J721e-evm.
Faiz Abbas [Wed, 26 Feb 2020 08:14:36 +0000 (13:44 +0530)]
arm: K3: sysfw-loader: Add a config_pm_pre_callback()
System firmware does not guarantee that clocks going out of the device
will be stable during power management configuration. There are some
DCRC errors when SPL tries to get the next stage during eMMC boot after
sysfw pm configuration.
Therefore add a config_pm_pre_callback() to switch off the eMMC clock
before power management and restart it after it is done.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Faiz Abbas [Wed, 26 Feb 2020 08:14:34 +0000 (13:44 +0530)]
mmc: am654_sdhci: Implement workaround for card detect
The 4 bit MMC controllers have an internal debounce for the SDCD line
with a debounce delay of 1 second. Therefore, after clocks to the IP are
enabled, software has to wait for this time before it can power on the
controller.
Add a deferred_probe() callback which polls on sdcd for a maximum of 2 seconds
before switching on power to the controller or (in the case of no card)
returning a ENOMEDIUM. This pushes the 1 second wait time to when the
card is actually needed rather than at every probe() making sure that
users who don't insert an SD card in the slot don't have to wait such a
long time.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Faiz Abbas [Wed, 26 Feb 2020 08:14:33 +0000 (13:44 +0530)]
mmc: am654_sdhci: Update output tap delay writes
With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Faiz Abbas [Wed, 26 Feb 2020 08:14:32 +0000 (13:44 +0530)]
mmc: Merge SD_LEGACY and MMC_LEGACY bus modes
MMC_LEGACY & SD_LEGACY are not differentiated timings in the spec and
don't have any meaningful differences. Therefore, get rid of all
references to SD_LEGACY and use MMC_LEGACY to mean both of them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Faiz Abbas [Wed, 26 Feb 2020 08:14:31 +0000 (13:44 +0530)]
sdhci: Add sdhci_deferred_probe() API
Add the sdhci_deferred_probe() function to register as the
deferred_probe() callback to the mmc core. It will in turn call the
deferred_probe() callback of the platform drivers as declared in the
sdhci_ops.
- Revert "x86: use invd instead of wbinvd in real mode start code"
- Convert toradex boards README to reST
- serial: ns16550: Move PCI access from ofdata_to_platdata() to probe()
- x86: apl: Use cpu_x86_get_count() for cpu_ops.get_count
Wolfgang Wallner [Tue, 25 Feb 2020 12:19:48 +0000 (13:19 +0100)]
x86: apl: Use cpu_x86_get_count() for cpu_ops.get_count
Use cpu_x86_get_count() to read the number of cores.
cpu_x86_get_count() reads the number of CPUs from the device tree.
Using this function we can support multiple Apollo Lake
variants, e.g.: E3940 (4 cores) and E3930 (2 cores).
This was tested on the E3940 and E3930 Apollo Lake variants.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wolfgang Wallner [Fri, 21 Feb 2020 11:20:09 +0000 (12:20 +0100)]
doc: Chromebook Coral: Fix typo for "Top of CAR region"
The value for "Top of CAR region" should be fefc0000, not fefc000. This matches the Kconfig default values, as
SYS_CAR_ADDR and SYS_CAR_SIZE are 0xfef00000 and 0xc0000
respectively.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wolfgang Wallner [Tue, 18 Feb 2020 14:32:10 +0000 (15:32 +0100)]
x86: p2sb: Drop 'apl' prefix
Drop the Apollo Lake prefix 'apl' from the functions, types and
variables in the P2SB driver.
The P2SB is not Apollo Lake specific, and as such it was moved in
commit 36779c18ac55 ("x86: Move P2SB from Apollo Lake to a more generic
location") from the Apollo Lake folder to the intel_common folder.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
serial: ns16550: Move PCI access from ofdata_to_platdata() to probe()
Currently the ofdata_to_platdata() method calls dev_read_addr_pci(),
which potentially accesses the parent PCI bus. If this happens before
the parent PCI bus is probed the resulting address will be wrong.
This behavior was triggered by commit 332eecf72d7b ("dm: core:
Allocate parent data separate from probing parent").
According to a comment in drivers/pci/pci-uclass.c [1] accessing
the PCI parent bus in ofdata_to_platdata() is not allowed, and the
access should be moved to the probe() function.
Move the call to dev_read_addr_pci() and the related handling of the
'addr' value from the ofdata_to_platdata() to its own function,
which is then called from the probe() method.
While moving the code, the comment /* try Processor Local Bus device
first */ was dropped. It was initially added with commit 3db886a5bf38
("serial: ns16550: Support ns16550 compatible pci uart devices") and
later made obsolete with commit 458f7d4f17b6 ("dm: pci: Add a function
to read a PCI BAR").
[1] Comment in drivers/pci/pci-uclass.c:
"A common cause of this problem is that this function is called in the
ofdata_to_platdata() method of @dev. Accessing the PCI bus in that
method is not allowed, since it has not yet been probed. To fix this,
move that access to the probe() method of @dev instead."
Fixes: 332eecf72d7b ("dm: core: Allocate parent data separate from probing parent") Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> # Tested on Intel Galileo
As real hardware testing (*) shows the above mentioned commit
breaks U-Boot on it. Revert for the upcoming release. We may get
more information in the future and optimize the code accordingly.
(*) on Intel Edison board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix a typo in the commit message] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Igor Opaniuk [Wed, 12 Feb 2020 15:14:29 +0000 (17:14 +0200)]
doc: board: verdin-imx8mm: convert readme to reST
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: spell out U-Boot correctly] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Igor Opaniuk [Wed, 12 Feb 2020 15:14:28 +0000 (17:14 +0200)]
doc: board: toradex: add colibri_imx7.rst
- add initial index for toradex boards reST documentation
- add initial colibri_imx7.rst doc file which provides all needed
information for obtaining a workable image ready for flashing
for both eMMC/NAND versions of Colibri iMX7.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: make title underline the same length as the title itself] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 2 Feb 2020 20:37:06 +0000 (13:37 -0700)]
x86: Correct error return value in mrccache_get_region()
This function doesn't use uclass_find_first_device() correctly. Add a
check that the device is found so we don't try to read properties from a
NULL device.
The fixes booting on minnoxmax.
Fixes: 8f172af47d3 ("x86: Adjust mrccache_get_region() to use livetree") Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add driver flag to skip power domain disabling on device removal.
Fixes: decfe1bdb42e ("dm: core: device: switch off power domain after device removal") Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Guillaume La Roque <glaroque@baylibre.com>
dm: core: Add a flag for power domain control on device removal
In various cases a power domain must stay enabled after device
removal when booting OS (i.e. serial debug console or display).
Add a flag to selectively skip switching off a power domain.
Fixes: decfe1bdb42e ("dm: core: device: switch off power domain after device removal") Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Guillaume La Roque <glaroque@baylibre.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Sat, 15 Feb 2020 13:10:02 +0000 (14:10 +0100)]
ARM: socfpga: Permit overriding the default timer frequency
The default timer rate may be different than 25 MHz, permit overriding
the default rate in board configuration file. Ultimatelly, this should
be properly handled by a clock driver, however that is not available
on Gen5 yet.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Ley Foon Tan <ley.foon.tan@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Marek Vasut [Sat, 15 Feb 2020 13:46:10 +0000 (14:46 +0100)]
rtc: m41t62: add compatible for m41st87
This adds a compatible string for m41st87. This ensures that this driver
can be used for m41st87.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de>
projects / uboot.git / log