Colin Ian King [Sun, 8 May 2022 21:45:00 +0000 (22:45 +0100)]
x25: remove redundant pointer dev
Pointer dev is being assigned a value that is never used, the assignment
and the variable are redundant and can be removed. Also replace null check
with the preferred !ptr idiom.
Cleans up clang scan warning:
net/x25/x25_proc.c:94:26: warning: Although the value stored to 'dev' is
used in the enclosing expression, the value is never actually read
from 'dev' [deadcode.DeadStores]
====================
This is a patch series for Ethernet driver of Sunplus SP7021 SoC.
Sunplus SP7021 is an ARM Cortex A7 (4 cores) based SoC. It integrates
many peripherals (ex: UART, I2C, SPI, SDIO, eMMC, USB, SD card and
etc.) into a single chip. It is designed for industrial control
applications.
Refer to:
https://sunplus.atlassian.net/wiki/spaces/doc/overview
https://tibbo.com/store/plus1.html
====================
====================
ptp: Support hardware clocks with additional free running cycle counter
ptp vclocks require a clock with free running time for the timecounter.
Currently only a physical clock forced to free running is supported.
If vclocks are used, then the physical clock cannot be synchronized
anymore. The synchronized time is not available in hardware in this
case. As a result, timed transmission with TAPRIO hardware support
is not possible anymore.
If hardware would support a free running time additionally to the
physical clock, then the physical clock does not need to be forced to
free running. Thus, the physical clocks can still be synchronized while
vclocks are in use.
The physical clock could be used to synchronize the time domain of the
TSN network and trigger TAPRIO. In parallel vclocks can be used to
synchronize other time domains.
One year ago I thought for two time domains within a TSN network also
two physical clocks are required. This would lead to new kernel
interfaces for asking for the second clock, ... . But actually for a
time triggered system like TSN there can be only one time domain that
controls the system itself. All other time domains belong to other
layers, but not to the time triggered system itself. So other time
domains can be based on a free running counter if similar mechanisms
like 2 step synchroisation are used.
Synchronisation was tested with two time domains between two directly
connected hosts. Each host run two ptp4l instances, the first used the
physical clock and the second used the virtual clock. I used my FPGA
based network controller as network device. ptp4l was used in
combination with the virtual clock support patches from Miroslav
Lichvar.
v4:
- if_index of 0 is invalid (Jonathan Lemon)
- set if_index to 0 in the SOF_TIMESTAMPING_RAW_HARDWARE block (Jonathan
Lemon)
- add helper function for netdev_get_tstamp() call (Jonathan Lemon)
- update SKBTX_ANY_TSTAMP (Paolo Abeni)
- use separate bits for new tx_flags (Richard Cochran)
v3:
- optimize ptp_convert_timestamp (Richard Cochran)
- call dev_get_by_napi_id() only if needed (Richard Cochran)
- use non-negated logical test (Richard Cochran)
- add comment for skipped output (Richard Cochran)
- add comment for SKBTX_HW_TSTAMP_USE_CYCLES masking (Richard Cochran)
The TSN endpoint Ethernet MAC supports a free running counter
additionally to its clock. This free running counter can be read and
hardware timestamps are supported. As the name implies, this counter
cannot be set and its frequency cannot be adjusted.
Add free running cycle counter support based on this free running
counter to physical clock. This also requires hardware time stamps
based on that free running counter.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ptp_convert_timestamp() is called in the RX path of network messages.
The current implementation takes ~5000ns on 1.2GHz A53. This is too much
for the hot path of packet processing.
Introduce hash table for fast vclock lookup in ptp_convert_timestamp().
The execution time of ptp_convert_timestamp() is reduced to ~700ns on
1.2GHz A53.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If a physical clock supports a free running cycle counter, then
timestamps shall be based on this time too. For TX it is known in
advance before the transmission if a timestamp based on the free running
cycle counter is needed. For RX it is impossible to know which timestamp
is needed before the packet is received and assigned to a socket.
Support late timestamp determination by a network device. Therefore, an
address/cookie is stored within the new netdev_data field of struct
skb_shared_hwtstamps. This address/cookie is provided to a new network
device function called ndo_get_tstamp(), which returns a timestamp based
on the normal/adjustable time or based on the free running cycle
counter. If function is not supported, then timestamp handling is not
changed.
This mechanism is intended for RX, but TX use is also possible.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ptp_convert_timestamp() converts only the timestamp hwtstamp, which is
a field of the argument with the type struct skb_shared_hwtstamps *. So
a pointer to the hwtstamp field of this structure is sufficient.
Rework ptp_convert_timestamp() to use an argument of type ktime_t *.
This allows to add additional timestamp manipulation stages before the
call of ptp_convert_timestamp().
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The free running cycle counter of physical clocks called cycles shall be
used for hardware timestamps to enable synchronisation.
Introduce new flag SKBTX_HW_TSTAMP_USE_CYCLES, which signals driver to
provide a TX timestamp based on cycles if cycles are supported.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ptp vclocks require a free running time for their timecounter.
Currently only a physical clock forced to free running is supported.
If vclocks are used, then the physical clock cannot be synchronized
anymore. The synchronized time is not available in hardware in this
case. As a result, timed transmission with TAPRIO hardware support
is not possible anymore.
If hardware would support a free running time additionally to the
physical clock, then the physical clock does not need to be forced to
free running. Thus, the physical clocks can still be synchronized
while vclocks are in use.
The physical clock could be used to synchronize the time domain of the
TSN network and trigger TAPRIO. In parallel vclocks can be used to
synchronize other time domains.
Introduce support for a free running cycle counter called cycles to
physical clocks. Rework ptp vclocks to use this free running cycle
counter. Default implementation is based on time of physical clock.
Thus, behavior of ptp vclocks based on physical clocks without free
running cycle counter is identical to previous behavior.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 6 May 2022 20:00:29 +0000 (13:00 -0700)]
eth: dpaa2-mac: remove a dead-code NULL check on fwnode parent
Since commit 4bbb2e40c23d ("dpaa2-mac: return -EPROBE_DEFER from dpaa2_mac_open in case the fwnode is not set")
@parent can't be NULL after the if. It's either the address
of the ->fwnode of @dpmacs or @fwnode in case of ACPI.
====================
nfp: support Corigine PCIE vendor ID
Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. This patch extends the driver to also support NFP
chips, which at this point are assumed to be otherwise identical from
a software perspective, that have Corigine's PCIE vendor ID (0x1da8).
This patchset begins by cleaning up strings to make them:
* Vendor neutral for the NFP chip
* Relate to Corigine for the driver itself
It then adds support to the driver for the Corigine's PCIE vendor ID
====================
Yu Xiao [Sun, 8 May 2022 17:38:16 +0000 (19:38 +0200)]
nfp: support Corigine PCIE vendor ID
Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. This patch extends the driver to also support NFP
chips, which at this point are assumed to be otherwise identical from
a software perspective, that have Corigine's PCIE vendor ID (0x1da8).
Also, Rename the macro definitions PCI_DEVICE_ID_NERTONEOME_NFPXXXX
to PCI_DEVICE_ID_NFPXXXX, as they are now used in conjunction with two
PCIE vendor IDs.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yu Xiao [Sun, 8 May 2022 17:38:15 +0000 (19:38 +0200)]
nfp: vendor neutral strings for chip and Corigne in strings for driver
Historically the nfp driver has supported NFP chips with Netronome's
PCIE vendor ID. In preparation for extending the to also support NFP
chips that have Corigine's PCIE vendor ID (0x1da8) make printk statements
relating to the chip vendor neutral.
An alternate approach is to set the string based on the PCI vendor ID.
In our judgement this proved to cumbersome so we have taken this simpler
approach.
Update strings relating to the driver to use Corigine, who have taken
over maintenance of the driver.
Signed-off-by: Yu Xiao <yu.xiao@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 10 May 2022 00:51:01 +0000 (17:51 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-05-06
Marcin Szycik says:
This patchset adds support for systemd defined naming scheme for port
representors, as well as re-enables displaying PCI bus-info in ethtool.
bus-info information has previously been removed from ethtool for port
representors, as a workaround for a bug in lshw tool, where the tool would
sometimes display wrong descriptions for port representors/PF. Now the bug
has been fixed in lshw tool [1].
Removing the workaround can be considered a regression (user might be
running an older, unpatched version of lshw) (see [2] for discussion).
However, calling SET_NETDEV_DEV also produces the same effect as removing
the workaround, i.e. lshw is able to access PCI bus-info (this time not
via ethtool, but in some other way) and the bug can occur.
Adding SET_NETDEV_DEV is important, as it greatly improves netdev naming -
- port representors are named based on PF name. Currently port representors
are named "ethX", which might be confusing, especially when spawning VFs on
multiple PFs. Furthermore, it's currently harder to determine to which PF
does a particular port representor belong, as bus-info is not shown in
ethtool.
Consider the following three cases:
Case 1: current code - driver workaround in place, no SET_NETDEV_DEV,
lshw with or without fix. Port representors are not displayed because they
don't have bus-info (the workaround), PFs are labelled correctly:
$ sudo ./lshw -c net -businfo
Bus info Device Class Description
========================================================
pci@0000:02:00.0 ens6f0 network Ethernet Controller E810-XXV for SFP <-- PF
pci@0000:02:00.1 ens6f1 network Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0 ens6f0v0 network Ethernet Adaptive Virtual Function <-- VF
pci@0000:02:01.1 ens6f0v1 network Ethernet Adaptive Virtual Function
...
Case 2: driver workaround in place, SET_NETDEV_DEV, no lshw fix. Port
representors have predictable names. lshw is able to get bus-info because
of SET_NETDEV_DEV and netdevs CAN be mislabelled:
$ sudo ./lshw -c net -businfo
Bus info Device Class Description
=============================================================
pci@0000:02:00.0 ens6f0npf0vf60 network Ethernet Controller E810-XXV for SFP <-- mislabeled port representor
pci@0000:02:00.1 ens6f1 network Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0 ens6f0v0 network Ethernet Adaptive Virtual Function
pci@0000:02:01.1 ens6f0v1 network Ethernet Adaptive Virtual Function
...
pci@0000:02:00.0 ens6f0npf0vf26 network Ethernet interface
pci@0000:02:00.0 ens6f0 network Ethernet interface <-- mislabeled PF
pci@0000:02:00.0 ens6f0npf0vf81 network Ethernet interface
...
$ sudo ethtool -i ens6f0npf0vf60
driver: ice
...
bus-info:
...
Output of lshw would be the same with workaround removed; it does not
change the fact that lshw labels netdevs incorrectly, while at the same
time it prevents ethtool from displaying potentially useful data
(bus-info).
Case 3: workaround removed, SET_NETDEV_DEV, lshw fix:
$ sudo ./lshw -c net -businfo
Bus info Device Class Description
=============================================================
pci@0000:02:00.0 ens6f0npf0vf73 network Ethernet Controller E810-XXV for SFP
pci@0000:02:00.1 ens6f1 network Ethernet Controller E810-XXV for SFP
pci@0000:02:01.0 ens6f0v0 network Ethernet Adaptive Virtual Function
pci@0000:02:01.1 ens6f0v1 network Ethernet Adaptive Virtual Function
...
pci@0000:02:00.0 ens6f0npf0vf5 network Ethernet Controller E810-XXV for SFP
pci@0000:02:00.0 ens6f0 network Ethernet Controller E810-XXV for SFP
pci@0000:02:00.0 ens6f0npf0vf60 network Ethernet Controller E810-XXV for SFP
...
$ sudo ethtool -i ens6f0npf0vf73
driver: ice
...
bus-info: 0000:02:00.0
...
In this case poort representors have predictable names, netdevs are not
mislabelled in lshw, and bus-info is shown in ethtool.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
Revert "ice: Hide bus-info in ethtool for PRs in switchdev mode"
ice: link representors to PCI device
====================
David S. Miller [Mon, 9 May 2022 13:30:38 +0000 (14:30 +0100)]
Merge branch 'hns3-next'
Guangbin Huang says:
====================
net: hns3: updates for -next
This series includes some updates for the HNS3 ethernet driver.
Change logs:
V1 -> V2:
- Fix some sparse warnings of patch 3# and 4#.
- Add patch #6 to fix sparse warnings of incorrect type of argument.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang [Mon, 9 May 2022 07:55:32 +0000 (15:55 +0800)]
net: hns3: fix incorrect type of argument in declaration of function hclge_comm_get_rss_indir_tbl
The argument rss_ind_tbl_size is type u16 in function definition of
hclge_comm_get_rss_indir_tbl(), but it is set to type __le16 in function
declaration by mistake, so fix it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Mon, 9 May 2022 07:55:30 +0000 (15:55 +0800)]
net: hns3: add byte order conversion for VF to PF mailbox message
This patch uses __le16/__32 to define mailbox data structures. Then byte
order conversion are added for mailbox messages from VF to PF.
Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Wang [Mon, 9 May 2022 07:55:29 +0000 (15:55 +0800)]
net: hns3: add byte order conversion for PF to VF mailbox message
Currently, hns3 mailbox processing between PF and VF missed to convert
message byte order and use data type u16 instead of __le16 for mailbox
data process. These processes may cause problems between different
architectures.
So this patch uses __le16/__le32 data type to define mailbox data
structures. To be compatible with old hns3 driver, these structures use
one-byte alignment. Then byte order conversions are added to mailbox
messages from PF to VF.
Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Mon, 9 May 2022 07:55:28 +0000 (15:55 +0800)]
net: hns3: remove the affinity settings of vector0
Vector0 is used for common interrupt control events and is
irrelevant to performance. Currently, the driver sets the
default affinity of vector0 to NUMA nodes, which is unnecessary.
Therefore, the default setting is removed, and the driver does
not set the affinity for vector0.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hao Chen [Mon, 9 May 2022 07:55:27 +0000 (15:55 +0800)]
net: hns3: fix access null pointer issue when set tx-buf-size as 0
When set tx-buf-size as 0 by ethtool, hns3_init_tx_spare_buffer()
will return directly and priv->ring->tx_spare->len is uninitialized,
then print function access priv->ring->tx_spare->len will cause
this issue.
When set tx-buf-size as 0 by ethtool, the print function will
print 0 directly and not access priv->ring->tx_spare->len.
Fixes: e033e2008394 ("net: hns3: add log for setting tx spare buf size") Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuiko Oshino [Thu, 5 May 2022 18:12:52 +0000 (11:12 -0700)]
net: phy: smsc: add LAN8742 phy support.
The current phy IDs on the available hardware.
LAN8742 0x0007C130, 0x0007C131
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuiko Oshino [Thu, 5 May 2022 18:12:51 +0000 (11:12 -0700)]
net: phy: microchip: update LAN88xx phy ID and phy ID mask.
update LAN88xx phy ID and phy ID mask because the existing code conflicts with the LAN8742 phy.
The current phy IDs on the available hardware.
LAN8742 0x0007C130, 0x0007C131
LAN88xx 0x0007C132
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
changes v3:
- export reusable code snippets and make use of it in the dp83td510
driver
changes v2:
- rewrite the driver reduce usage of common code and to reduce amount of
quirks.
- add genphy_c45_baset1_an_config_aneg fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel [Fri, 6 May 2022 04:23:55 +0000 (06:23 +0200)]
net: phy: genphy_c45_pma_baset1_read_master_slave: read actual configuration
Since MDIO_PMA_PMD_BT1_CTRL register shows actual configuration (and
forced state configuration is equal to the state), we should show
this configuration for ethtool.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel [Fri, 6 May 2022 04:23:51 +0000 (06:23 +0200)]
net: phy: genphy_c45_baset1_an_config_aneg: do no set unknown configuration
Do not change default master/slave autoneg configuration if no
changes was requested.
Fixes: 101de7da0e4f ("net: phy: Add 10BASE-T1L support in phy-c45") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Alaa Mohamed [Thu, 5 May 2022 15:09:58 +0000 (17:09 +0200)]
net: vxlan: Add extack support to vxlan_fdb_delete
This patch adds extack msg support to vxlan_fdb_delete and vxlan_fdb_parse.
extack is used to propagate meaningful error msgs to the user of vxlan
fdb netlink api
Signed-off-by: Alaa Mohamed <eng.alaamohamedsoliman.am@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 May 2022 09:51:59 +0000 (10:51 +0100)]
Merge branch 'wwan-t7xx'
Ricardo Martinez says:
====================
net: wwan: t7xx: PCIe driver for MediaTek M.2 modem
t7xx is the PCIe host device driver for Intel 5G 5000 M.2 solution which
is based on MediaTek's T700 modem to provide WWAN connectivity.
The driver uses the WWAN framework infrastructure to create the following
control ports and network interfaces:
* /dev/wwan0mbim0 - Interface conforming to the MBIM protocol.
Applications like libmbim [1] or Modem Manager [2] from v1.16 onwards
with [3][4] can use it to enable data communication towards WWAN.
* /dev/wwan0at0 - Interface that supports AT commands.
* wwan0 - Primary network interface for IP traffic.
The main blocks in t7xx driver are:
* PCIe layer - Implements probe, removal, and power management callbacks.
* Port-proxy - Provides a common interface to interact with different types
of ports such as WWAN ports.
* Modem control & status monitor - Implements the entry point for modem
initialization, reset and exit, as well as exception handling.
* CLDMA (Control Layer DMA) - Manages the HW used by the port layer to send
control messages to the modem using MediaTek's CCCI (Cross-Core
Communication Interface) protocol.
* DPMAIF (Data Plane Modem AP Interface) - Controls the HW that provides
uplink and downlink queues for the data path. The data exchange takes
place using circular buffers to share data buffer addresses and metadata
to describe the packets.
* MHCCIF (Modem Host Cross-Core Interface) - Provides interrupt channels
for bidirectional event notification such as handshake, exception, PM and
port enumeration.
The compilation of the t7xx driver is enabled by the CONFIG_MTK_T7XX config
option which depends on CONFIG_WWAN.
This driver was originally developed by MediaTek. Intel adapted t7xx to
the WWAN framework, optimized and refactored the driver source code in close
collaboration with MediaTek. This will enable getting the t7xx driver on the
Approved Vendor List for interested OEM's and ODM's productization plans
with Intel 5G 5000 M.2 solution.
List of contributors:
Amir Hanania <amir.hanania@intel.com>
Andriy Shevchenko <andriy.shevchenko@linux.intel.com>
Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Dinesh Sharma <dinesh.sharma@intel.com>
Eliot Lee <eliot.lee@intel.com>
Haijun Liu <haijun.liu@mediatek.com>
M Chetan Kumar <m.chetan.kumar@intel.com>
Mika Westerberg <mika.westerberg@linux.intel.com>
Moises Veleta <moises.veleta@intel.com>
Pierre-louis Bossart <pierre-louis.bossart@intel.com>
Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Ricardo Martinez <ricardo.martinez@linux.intel.com>
Madhusmita Sahu <madhusmita.sahu@intel.com>
Muralidharan Sethuraman <muralidharan.sethuraman@intel.com>
Soumya Prakash Mishra <Soumya.Prakash.Mishra@intel.com>
Sreehari Kancharla <sreehari.kancharla@intel.com>
Suresh Nagaraj <suresh.nagaraj@intel.com>
V7:
- Delete unused macros.
- Avoid duplicated calls to le32_to_cpu().
- Fix 'out of bounds' compilation error.
- Rename port_number to port_count.
- Remove '!!' when the destination variable is a boolean.
- Remove unneeded spinlock around rx_length_th.
- Remove common field from union inside dpmaif_drb struct.
- Use 'goto' for the exit flow in t7xx_pci_enable_sleep().
- Merge CLDMA tgpd and rgpd structs.
- Add comments to clarify skb consumption by ports.
- Introduce skb_data_area_size() helper.
- Declare the port config array as constant.
- Update CLDMA_JUMBO_BUFF_SZ definition when ccci_header
is introduced by port-proxy patch.
- Update Reviewed-by tags.
- Simplify t7xx_dpmaif_tx_send_skb() and make t7xx_dpmaif_add_skb_to_ring()
report the tx queue full state early.
V6:
- Remove unneeded initializations and bit masks.
- Remove t7xx_common.h file.
- Add comment to circular linking in GPD list.
- Use min instead of min_t.
- Use int for local indexes instead of short or char.
- Update the commit message in CLDMA patch about dependencies on core patch.
- Add space between contributor name and email address.
- Rename registers with double negatives
e.g. DIS_ASPM_LOWPWR_CLR_0 -> ENABLE_ASPM_LOWPWR.
- Fix a race condition in pci sleep resource locking.
- Initialize interrupts with t7xx_pcie_mac_set_int() instead of 'clear'.
- Remove duplicate spin_lock_init(&md->exp_lock).
- Remove .ndo_select_queue callback due to singular TX queue.
- Remove call to deprecated netif_rx_any_context().
- Fix include guard name in t7xx_hif_dpmaif.h.
- Remove unused q_num parameter in DPMAIF functions.
- Do not serialize the drb_wr_idx write in t7xx_dpmaif_add_skb_to_ring()
and the read from t7xx_txq_drb_wr_available().
- Fix potential leak in t7xx_dpmaif_add_skb_to_ring().
- Unionize:
DRB structs: msg and pd.
PIT structs: msg and pd.
- Replace list_head & spinlock with skb_buff_head in dpmaif_tx_queue.
- Remove rx_length_th check in TX WWAN port flow.
- Remove wwan_remove_port() from the critical section in WWAN port uninit.
- Use skb_end_pointer() to avoid conditional compilation.
- Simplify the loop in t7xx_port_ctrl_tx() by checking the buffer offset
instead of calculating the number of required packets.
- Remove the code for unused channel PORT_CH_STATUS_RX.
- Remove bit flags from ports. Ports can check chan_enable instead of the
PORT_F_RX_ALLOW_DROP flag.
- Use INVALID_SEQ_NUM to identify the first seq number.
- Rename port_static to port_conf and ports_private to ports.
- Implement t7xx_port_send_skb() and t7xx_port_send_ctl_skb() in a layered
approach to reduce duplicated code and simplify the CCCI header handling.
- Move wwan_port_rx() call from port-proxy to WWAN port.
- Rename t7xx_port_recv_skb() to t7xx_port_enqueue_skb().
- Move control message parsing logic from port-proxy to control port,
preserve the endianness when parsing the message and make port-proxy
export a function to enable/disable ports.
- Use flexible arrays for:
port-proxy ports.
payload data in t7xx_fsm_event, port_msg, and mtk_runtime_feature.
v5:
- Update Intel's copyright years to 2021-2022.
- Remove circular dependency between DPMAIF HW (07) and HIF (08).
- Keep separate patches for CLDMA (02) and Core (03)
but improve the code split by decoupling CLDMA from
modem ops and cleaning up t7xx_common.h.
- Rename ID_CLDMA0/ID_CLDMA1 to CLDMA_ID_AP/CLDMA_ID_MD.
- Consistently use CLDMA's ring_lock to protect tr_ring.
- Free resources first and then print messages.
- Implement suggested name changes.
- Do not explicitly include dev_printk.h.
- Remove redundant dev_err()s.
- Fix possible memory leak during probe.
- Remove infrastructure for legacy interrupts.
- Remove unused macros and variables, including those that
can be replaced with constants.
- Remove PCIE_MAC_MSIX_MSK_SET macro which is duplicated code.
- Refactor __t7xx_pci_pm_suspend() for clarity.
- Refactor t7xx_cldma_rx_ring_init() and t7xx_cldma_tx_ring_init().
- Do not use & for function callbacks.
- Declare a structure to access skb->cb[] data.
- Use skb_put_data instead of memcpy.
- No need to use kfree_sensitive.
- Use dev_kfree_skb() instead of kfree_skb().
- Refactor t7xx_prepare_device_rt_data() to remove potential leaks,
avoid unneeded memset and keep rt_data and packet_size updates
inside the same 'if' block.
- Set port's rx_length_th back to 0 during uninit.
- Remove unneeded 'blocking' parameter from t7xx_cldma_send_skb().
- Return -EIO in t7xx_cldma_send_skb() if the queue is inactive.
- Refactor t7xx_cldma_qs_are_active() to use pci_device_is_present().
- Simplify t7xx_cldma_stop_q() and rename it to t7xx_cldma_stop_all_qs().
- Fix potential leaks in t7xx_cldma_init().
- Improve error handling in fsm_append_event and fsm_routine_starting().
- Propagate return codes from fsm_append_cmd() and t7xx_fsm_append_event().
- Refactor fsm_wait_for_event() to avoid unnecessary sleep.
- Create the WWAN ports and net device only after the modem is in
the ready state.
- Refactor t7xx_port_proxy_recv_skb() and port_recv_skb().
- Rename t7xx_port_check_rx_seq_num() as t7xx_port_next_rx_seq_num()
and fix the seq_num logic to handle overflows.
- Declare seq_nums as u16 instead of short.
- Use unsigned int for local indexes.
- Use min_t instead of the ternary operator.
- Refactor the loop in t7xx_dpmaif_rx_data_collect() to avoid a dead
condition check.
- Use a bitmap (bat_bitmap) instead of an array to keep track of
the DRB status. Used in t7xx_dpmaif_avail_pkt_bat_cnt().
- Refactor t7xx_dpmaif_tx_send_skb() to protect tx_submit_skb_cnt
with spinlock and remove the misleading tx_drb_available variable.
- Consolidate bit operations before endianness conversion.
- Use C bit fields in dpmaif_drb_skb struct which is not HW related.
- Add back the que_started check in t7xx_select_tx_queue().
- Create a helper function to get the DRB count.
- Simplify the use of 'usage' during t7xx_ccmni_close().
- Enforce CCMNI MTU selection with BUILD_BUG_ON() instead of a comment.
- Remove t7xx_ccmni_ctrl->capability parameter which remains constant.
v4:
- Implement list_prev_entry_circular() and list_next_entry_circular() macros.
- Remove inline from all c files.
- Define ioread32_poll_timeout_atomic() helper macro.
- Fix return code for WWAN port tx op.
- Allow AT commands fragmentation same as MBIM commands.
- Introduce t7xx_common.h file in the first patch.
- Rename functions and variables as suggested in v3.
- Reduce code duplication by creating fsm_wait_for_event() helper function.
- Remove unneeded dev_err in t7xx_fsm_clr_event().
- Remove unused variable last_state from struct t7xx_fsm_ctl.
- Remove unused variable txq_select_times from struct dpmaif_ctrl.
- Replace ETXTBSY with EBUSY.
- Refactor t7xx_dpmaif_rx_buf_alloc() to remove an unneeded allocation.
- Fix potential leak at t7xx_dpmaif_rx_frag_alloc().
- Simplify return value handling at t7xx_dpmaif_rx_start().
- Add a helper to handle the common part of CCCI header initialization.
- Make sure interrupts are enabled during PM resume.
- Add a parameter to t7xx_fsm_append_cmd() to tell if it is in interrupt context.
v3:
- Avoid unneeded ping-pong changes between patches.
- Use t7xx_ prefix in functions.
- Use t7xx_ prefix in generic structs where mtk_ or ccci prefix was used.
- Update Authors/Contributors header.
- Remove skb pools used for control path.
- Remove skb pools used for RX data path.
- Do not use dedicated TX queue for ACK-only packets.
- Remove __packed attribute from GPD structs.
- Remove the infrastructure for test and debug ports.
- Use the skb control buffer to store metadata.
- Get the IP packet type from RX PIT.
- Merge variable declaration and simple assignments.
- Use preferred coding patterns.
- Remove global variables.
- Declare HW facing structure members as little endian.
- Rename goto tags to describe what is going to be done.
- Do not use variable length arrays.
- Remove unneeded blank lines source code and kdoc headers.
- Use C99 initialization format for port-proxy ports.
- Clean up comments.
- Review included headers.
- Better use of 100 column limit.
- Remove unneeded mb() in CLDMA.
- Remove unneeded spin locks and atomics.
- Handle read_poll_timeout error.
- Use dev_err_ratelimited() where required.
- Fix resource leak when requesting IRQs.
- Use generic DEFAULT_TX_QUEUE_LEN instead custom macro.
- Use ETH_DATA_LEN instead of defining WWAN_DEFAULT_MTU.
- Use sizeof() instead of defines when the size of structures is required.
- Remove unneeded code from netdev:
No need to configure HW address length
No need to implement .ndo_change_mtu
Remove random address generation
- Code simplifications by using kernel provided functions and macros such as:
module_pci_driver
PTR_ERR_OR_ZERO
for_each_set_bit
pci_device_is_present
skb_queue_purge
list_prev_entry
__ffs64
v2:
- Replace pdev->driver->name with dev_driver_string(&pdev->dev).
- Replace random_ether_addr() with eth_random_addr().
- Update kernel-doc comment for enum data_policy.
- Indicate the driver is 'Supported' instead of 'Maintained'.
- Fix the Signed-of-by and Co-developed-by tags in the patches.
- Added authors and contributors in the top comment of the src files.
====================
Haijun Liu [Fri, 6 May 2022 18:13:09 +0000 (11:13 -0700)]
net: wwan: t7xx: Device deep sleep lock/unlock
Introduce the mechanism to lock/unlock the device 'deep sleep' mode.
When the PCIe link state is L1.2 or L2, the host side still can keep
the device is in D0 state from the host side point of view. At the same
time, if the device's 'deep sleep' mode is unlocked, the device will
go to 'deep sleep' while it is still in D0 state on the host side.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:13:08 +0000 (11:13 -0700)]
net: wwan: t7xx: Runtime PM
Enables runtime power management callbacks including runtime_suspend
and runtime_resume. Autosuspend is used to prevent overhead by frequent
wake-ups.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Eliot Lee <eliot.lee@intel.com> Signed-off-by: Eliot Lee <eliot.lee@intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:13:07 +0000 (11:13 -0700)]
net: wwan: t7xx: Introduce power management
Implements suspend, resumes, freeze, thaw, poweroff, and restore
`dev_pm_ops` callbacks.
From the host point of view, the t7xx driver is one entity. But, the
device has several modules that need to be addressed in different ways
during power management (PM) flows.
The driver uses the term 'PM entities' to refer to the 2 DPMA and
2 CLDMA HW blocks that need to be managed during PM flows.
When a dev_pm_ops function is called, the PM entities list is iterated
and the matching function is called for each entry in the list.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:13:06 +0000 (11:13 -0700)]
net: wwan: t7xx: Add WWAN network interface
Creates the Cross Core Modem Network Interface (CCMNI) which implements
the wwan_ops for registration with the WWAN framework, CCMNI also
implements the net_device_ops functions used by the network device.
Network device operations include open, close, start transmission, TX
timeout and change MTU.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Co-developed-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:13:05 +0000 (11:13 -0700)]
net: wwan: t7xx: Add data path interface
Data Path Modem AP Interface (DPMAIF) HIF layer provides methods
for initialization, ISR, control and event handling of TX/RX flows.
DPMAIF TX
Exposes the 'dmpaif_tx_send_skb' function which can be used by the
network device to transmit packets.
The uplink data management uses a Descriptor Ring Buffer (DRB).
First DRB entry is a message type that will be followed by 1 or more
normal DRB entries. Message type DRB will hold the skb information
and each normal DRB entry holds a pointer to the skb payload.
DPMAIF RX
The downlink buffer management uses Buffer Address Table (BAT) and
Packet Information Table (PIT) rings.
The BAT ring holds the address of skb data buffer for the HW to use,
while the PIT contains metadata about a whole network packet including
a reference to the BAT entry holding the data buffer address.
The driver reads the PIT and BAT entries written by the modem, when
reaching a threshold, the driver will reload the PIT and BAT rings.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:13:04 +0000 (11:13 -0700)]
net: wwan: t7xx: Data path HW layer
Data Path Modem AP Interface (DPMAIF) HW layer provides HW abstraction
for the upper layer (DPMAIF HIF). It implements functions to do the HW
configuration, TX/RX control and interrupt handling.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Adds AT and MBIM ports to the port proxy infrastructure.
The initialization method is responsible for creating the corresponding
ports using the WWAN framework infrastructure. The implemented WWAN port
operations are start, stop, and TX.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:13:02 +0000 (11:13 -0700)]
net: wwan: t7xx: Add control port
Control Port implements driver control messages such as modem-host
handshaking, controls port enumeration, and handles exception messages.
The handshaking process between the driver and the modem happens during
the init sequence. The process involves the exchange of a list of
supported runtime features to make sure that modem and host are ready
to provide proper feature lists including port enumeration. Further
features can be enabled and controlled in this handshaking process.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:13:01 +0000 (11:13 -0700)]
net: wwan: t7xx: Add port proxy infrastructure
Port-proxy provides a common interface to interact with different types
of ports. Ports export their configuration via `struct t7xx_port` and
operate as defined by `struct port_ops`.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Co-developed-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:13:00 +0000 (11:13 -0700)]
net: wwan: t7xx: Add core components
Registers the t7xx device driver with the kernel. Setup all the core
components: PCIe layer, Modem Host Cross Core Interface (MHCCIF),
modem control operations, modem state machine, and build
infrastructure.
* PCIe layer code implements driver probe and removal.
* MHCCIF provides interrupt channels to communicate events
such as handshake, PM and port enumeration.
* Modem control implements the entry point for modem init,
reset and exit.
* The modem status monitor is a state machine used by modem control
to complete initialization and stop. It is used also to propagate
exception events reported by other components.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haijun Liu [Fri, 6 May 2022 18:12:59 +0000 (11:12 -0700)]
net: wwan: t7xx: Add control DMA interface
Cross Layer DMA (CLDMA) Hardware interface (HIF) enables the control
path of Host-Modem data transfers. CLDMA HIF layer provides a common
interface to the Port Layer.
CLDMA manages 8 independent RX/TX physical channels with data flow
control in HW queues. CLDMA uses ring buffers of General Packet
Descriptors (GPD) for TX/RX. GPDs can represent multiple or single
data buffers (DB).
CLDMA HIF initializes GPD rings, registers ISR handlers for CLDMA
interrupts, and initializes CLDMA HW registers.
CLDMA TX flow:
1. Port Layer write
2. Get DB address
3. Configure GPD
4. Triggering processing via HW register write
CLDMA RX flow:
1. CLDMA HW sends a RX "done" to host
2. Driver starts thread to safely read GPD
3. DB is sent to Port layer
4. Create a new buffer for GPD ring
Note: This patch does not enable compilation since it has dependencies
such as t7xx_pcie_mac_clear_int()/t7xx_pcie_mac_set_int() and
struct t7xx_pci_dev which are added by the core patch.
Signed-off-by: Haijun Liu <haijun.liu@mediatek.com> Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com> Co-developed-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Loic Poulain <loic.poulain@linaro.org> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Helper to calculate the linear data space in the skb.
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
list: Add list_next_entry_circular() and list_prev_entry_circular()
Add macros to get the next or previous entries and wraparound if
needed. For example, calling list_next_entry_circular() on the last
element should return the first element in the list.
Signed-off-by: Ricardo Martinez <ricardo.martinez@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mlxsw: A dedicated notifier block for router code
Petr says:
Currently all netdevice events are handled in the centralized notifier
handler maintained by spectrum.c. Since a number of events are involving
router code, spectrum.c needs to dispatch them to spectrum_router.c. The
spectrum module therefore needs to know more about the router code than it
should have, and there is are several API points through which the two
modules communicate.
In this patchset, move bulk of the router-related event handling to the
router code. Some of the knowledge has to stay: spectrum.c cannot veto
events that the router supports, and vice versa. But beyond that, the two
can ignore each other's details, which leads to more focused and simpler
code.
As a side effect, this fixes L3 HW stats support on tunnel netdevices.
The patch set progresses as follows:
- In patch #1, change spectrum code to not bounce L3 enslavement, which the
router code supports.
- In patch #2, add a new do-nothing notifier block to the router code.
- In patches #3-#6, move router-specific event handling to the router
module. In patch #7, clean up a comment.
- In patch #8, use the advantage that all router event handling is in the
router code and clean up taking router lock.
- mlxsw supports L3 HW stats on tunnels as of this patchset. Patches #9 and
#10 therefore add a selftest for L3 HW stats support on tunnels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:22 +0000 (11:08 +0300)]
selftests: lib: Add a generic helper for obtaining HW stats
The function get_l3_stats() from the test hw_stats_l3.sh will be useful for
any test that wishes to work with L3 stats. Furthermore, it is easy to
generalize to other HW stats suites (for when such are added). Therefore,
move the code to lib.sh, rewrite it to have the same interface as the other
stats-collecting functions, and generalize to take the name of the HW stats
suite to collect as an argument.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:21 +0000 (11:08 +0300)]
mlxsw: spectrum_router: Take router lock in router notifier handler
For notifications that the router needs to handle, router lock is taken.
Further, at least to determine whether an event is related to a tunnel
underlay, router lock also needs to be taken. Due to this, the router lock
is always taken for each unhandled event, and also for some handled events,
even if they are not related to underlay. Thus each event implies at least
one router lock, sometimes two.
Instead of deferring the locking to the leaf handlers, take the lock in the
router notifier handler always. This simplifies thinking about the locking
state, and in some cases saves one lock cycle.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:20 +0000 (11:08 +0300)]
mlxsw: spectrum: Update a comment
The position of netdevice notifier registration no longer depends on the
router initialization, because the event handler no longer dispatches to
the router code. Update the comment at the registration to that effect.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:19 +0000 (11:08 +0300)]
mlxsw: spectrum: Move handling of tunnel events to router code
The events related to IPIP tunnels are handled by the router code. Move the
handling from the central dispatcher in spectrum.c to the new notifier
handler in the router module.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:18 +0000 (11:08 +0300)]
mlxsw: spectrum: Move handling of router events to router code
The events NETDEV_PRE_CHANGEADDR, NETDEV_CHANGEADDR and NETDEV_CHANGEMTU
have implications for in-ASIC router interface objects, and as such are
handled in the router module. Move the handling from the central dispatcher
in spectrum.c to the new notifier handler in the router module.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:17 +0000 (11:08 +0300)]
mlxsw: spectrum: Move handling of HW stats events to router code
L3 HW stats are implemented in mlxsw as RIF counters, and therefore the
code resides in spectrum_router. Exclude the offload xstats events from the
mlxsw_sp_netdevice_event_is_router() predicate, and instead recreate the
glue code in the router module.
Previously, the order of dispatch was that for events on tunnels, a
dedicated handler was called, which however did not handle HW stats events.
But there is nothing special about tunnel devices as far as HW stats: there
is a RIF associated with the tunnel netdevice, and that RIF is where the
counter should be installed. Therefore now, HW stats events are tested
first, independent of netdevice type. The upshot is that as of this commit,
mlxsw supports L3 HW stats work on GRE tunnels.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:16 +0000 (11:08 +0300)]
mlxsw: spectrum: Move handling of VRF events to router code
Events involving VRF, as L3 concern, are handled in the router code, by the
helper mlxsw_sp_netdevice_vrf_event(). The handler is currently invoked
from the centralized dispatcher in spectrum.c. Instead, move the call to
the newly-introduced router-specific notifier handler.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:15 +0000 (11:08 +0300)]
mlxsw: spectrum_router: Add a dedicated notifier block
Currently all netdevice events are handled in the centralized notifier
handler maintained by spectrum.c. Since a number of events are involving
router code, spectrum.c needs to dispatch them to spectrum_router.c. The
spectrum module therefore needs to know more about the router code than it
should have, and there is are several API points through which the two
modules communicate.
To simplify the notifier handlers, introduce a new notifier into the router
module.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 8 May 2022 08:08:14 +0000 (11:08 +0300)]
mlxsw: spectrum: Tolerate enslaving of various devices to VRF
Enslaving netdevices to VRF is currently handled through an
mlxsw_sp_is_vrf_event() conditional in mlxsw_sp_netdevice_event(). In the
following patch sets, VRF enslavement will be handled purely in the router
code. Therefore make handlers of NETDEV_PRECHANGEUPPER tolerant of
enslaving to VRF, so that they do not bounce the change.
For NETDEV_CHANGEUPPER, drop the WARN_ON(1) and bounce from
mlxsw_sp_netdevice_port_vlan_event(). This is the only handler that warned
and bounces even in the CHANGEUPPER code, other handler quietly do nothing
when they encounter an unfamiliar upper.
Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: switch drivers to netif_napi_add_weight()
The minority of drivers pass a custom weight to netif_napi_add().
Switch those away to the new netif_napi_add_weight(). All drivers
(which can go thru net-next) calling netif_napi_add() will now
be calling it with NAPI_POLL_WEIGHT or 64.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 6 May 2022 17:07:50 +0000 (10:07 -0700)]
net: virtio: switch to netif_napi_add_weight()
virtio netdev driver uses a custom napi weight, switch to the new
API for setting custom weight.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Simplify migration of host filtered addresses in Felix driver
The purpose of this patch set is to remove the functions
dsa_port_walk_fdbs() and dsa_port_walk_mdbs() from the DSA core, which
were introduced when the Felix driver gained support for unicast
filtering on standalone ports. They get called when changing the tagging
protocol back and forth between "ocelot" and "ocelot-8021q".
I did not realize we could get away without having them.
The patch set was regression-tested using the local_termination.sh
selftest using both tagging protocols.
====================
Vladimir Oltean [Thu, 5 May 2022 16:22:12 +0000 (19:22 +0300)]
net: dsa: felix: perform MDB migration based on ocelot->multicast list
The felix driver is the only user of dsa_port_walk_mdbs(), and there
isn't even a good reason for it, considering that the host MDB entries
are already saved by the ocelot switch lib in the ocelot->multicast list.
Rewrite the multicast entry migration procedure around the
ocelot->multicast list so we can delete dsa_port_walk_mdbs().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Thu, 5 May 2022 16:22:11 +0000 (19:22 +0300)]
net: dsa: felix: stop migrating FDBs back and forth on tag proto change
I just realized we don't need to migrate the host-filtered FDB entries
when the tagging protocol changes from "ocelot" to "ocelot-8021q".
Host-filtered addresses are learned towards the PGID_CPU "multicast"
port group, reserved by software, which contains BIT(ocelot->num_phys_ports).
That is the "special" port entry in the analyzer block for the CPU port
module.
In "ocelot" mode, the CPU port module's packets are redirected to the
NPI port.
In "ocelot-8021q" mode, felix_8021q_cpu_port_init() does something funny
anyway, and changes PGID_CPU to stop pointing at the CPU port module and
start pointing at the physical port where the DSA master is attached.
The fact that we can alter the destination of packets learned towards
PGID_CPU without altering the MAC table entries themselves means that it
is pointless to walk through the FDB entries, forget that they were
learned towards PGID_CPU, and re-learn them towards the "unicast" PGID
associated with the physical port connected to the DSA master. We can
let the PGID_CPU value change simply alter the destination of the
host-filtered unicast packets in one fell swoop.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Thu, 5 May 2022 16:22:10 +0000 (19:22 +0300)]
net: dsa: felix: use PGID_CPU for FDB entry migration on NPI port
ocelot_fdb_add() redirects FDB entries installed on the NPI port towards
the special reserved PGID_CPU used for host-filtered addresses. PGID_CPU
contains BIT(ocelot->num_phys_ports) in the destination port mask, which
is code name for the CPU port module.
Whereas felix_migrate_fdbs_to_*_port() uses the ocelot->num_phys_ports
PGID directly, and it appears that this works too. Even if this PGID is
set to zero, apparently its number is special and packets still reach
the CPU port module.
Nonetheless, in the end, these addresses end up in the same place
regardless of whether they go through an extra indirection layer or not.
Use PGID_CPU across to have more uniformity.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Thompson [Thu, 5 May 2022 16:23:09 +0000 (12:23 -0400)]
mlxbf_gige: increase MDIO polling rate to 5us
This patch increases the polling rate used by the
mlxbf_gige driver on the MDIO bus. The previous
polling rate was every 100us, and the new rate is
every 5us. With this change the amount of time
spent waiting for the MDIO BUSY signal to de-assert
drops from ~100us to ~27us for each operation.
Jakub Kicinski [Fri, 6 May 2022 22:39:28 +0000 (15:39 -0700)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
10GbE Intel Wired LAN Driver Updates 2022-05-05
This series contains updates to ixgbe and igb drivers.
Jeff Daly adjusts type for 'allow_unsupported_sfp' to match the
associated struct value for ixgbe.
Alaa Mohamed converts, deprecated, kmap() call to kmap_local_page() for
igb.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igb: Convert kmap() to kmap_local_page()
ixgbe: Fix module_param allow_unsupported_sfp type
====================
Commit 995e48660e0f ("ice: Hide bus-info in ethtool for PRs in switchdev
mode") was a workaround for lshw tool displaying incorrect
descriptions for port representors and PF in switchdev mode. Now the issue
has been fixed in the lshw tool itself [1].
Removing the workaround can be considered a regression, as the user might
be running older, unpatched lshw version. However, another important change
(ice: link representors to PCI device, which improves port representor
netdev naming with SET_NETDEV_DEV) also causes the same "regression" as
removing the workaround, i.e. unpatched lshw is able to access bus-info
information (this time not via ethtool) and the bug can occur. Therefore,
the workaround no longer prevents the bug and can be removed.
David S. Miller [Fri, 6 May 2022 11:07:56 +0000 (12:07 +0100)]
Merge branch 'tso-gso-limit-split'
Jakub Kicinski says:
====================
net: disambiguate the TSO and GSO limits
This series separates the device-reported TSO limitations
from the user space-controlled GSO limits. It used to be that
we only had the former (HW limits) but they were named GSO.
This probably lead to confusion and letting user override them.
The problem came up in the BIG TCP discussion between Eric and
Alex, and seems like something we should address.
Targeting net-next because (a) nobody is reporting problems;
and (b) there is a tiny but non-zero chance that some actually
wants to lift the HW limitations.
====================
Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 6 May 2022 02:51:32 +0000 (19:51 -0700)]
net: don't allow user space to lift the device limits
Up until commit b60d324269f8 ("rtnetlink: allow GSO maximums to
be set on device creation") the gso_max_segs and gso_max_size
of a device were not controlled from user space.
The quoted commit added the ability to control them because of
the following setup:
netns A | netns B
veth<->veth eth0
If eth0 has TSO limitations and user wants to efficiently forward
traffic between eth0 and the veths they should copy the TSO
limitations of eth0 onto the veths. This would happen automatically
for macvlans or ipvlan but veth users are not so lucky (given the
loose coupling).
Unfortunately the commit in question allowed users to also override
the limits on real HW devices.
It may be useful to control the max GSO size and someone may be using
that ability (not that I know of any user), so create a separate set
of knobs to reliably record the TSO limitations. Validate the user
requests.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 6 May 2022 02:51:31 +0000 (19:51 -0700)]
net: add netif_inherit_tso_max()
To make later patches smaller create a helper for inheriting
the TSO limitations of a lower device. The TSO in the name
is not an accident, subsequent patches will replace GSO
with TSO in more names.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series reworks the way in which flow rules that outputs to
OVS internal ports gets handled by the nfp driver.
Previously this made use of a small pre_tun_table, but this only used
destination MAC addresses, and made the implicit assumption that there is
only a single source MAC":"destination MAC" mapping per tunnel. In
hindsight this seems to be a pretty obvious oversight, but this was hidden
in plain sight for quite some time.
This series changes the implementation to make use of the same Neighbour
table for decap that is in use for the tunnel encap solution. It stores
any new Neighbour updates in this table. Previously this path was only
triggered for encapsulation candidates, and the entries were send and
forget, not saved on the host as it is after this series. It also keeps
track of any flow rule that outputs to OVS internal ports (and some
other criteria not worth mentioning here), very similar to how it was
done previously, except now these flows are kept track of in a list.
When a new Neighbour entry gets added this list gets iterated for
potential matches, in which case the table gets updated with a reference
to the flow, and the Neighbour entry on the card gets updated with the
relevant host_ctx. The same happens when a new qualifying flow gets
added - the Neighbour table gets iterated for applicable matches, and
once again the firmware gets updated with the host_ctx when any matches
are found.
Since this also requires a firmware change we add a new capability bit,
and keep the old behaviour in case of older firmware without this bit
set.
This series starts by doing some preparation, then adding the new list
and table entries. Next the functionality to link/unlink these entries
are added, and finally this new functionality is enabled by adding the
DECAP_V2 bit to the driver feature list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:48 +0000 (14:43 +0900)]
nfp: flower: enable decap_v2 bit
Finally enable the decap_v2 feature bit now that all the
other bits are in place to configure it correctly.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:47 +0000 (14:43 +0900)]
nfp: flower: remove unused neighbour cache
With the neighbour entries now stored in a dedicated table there
is no use to make use of the tunnel route cache anymore, so remove
this.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:46 +0000 (14:43 +0900)]
nfp: flower: link pre_tun flow rules with neigh entries
Add helper functions that can create links between flow rules
and cached neighbour entries. Also add the relevant calls to
these functions.
* When a new neighbour entry gets added cycle through the saved
pre_tun flow list and link any relevant matches. Update the
neighbour table on the nfp with this new information.
* When a new pre_tun flow rule gets added iterate through the
save neighbour entries and link any relevant matches. Once
again update the nfp neighbour table with any new links.
* Do the inverse when deleting - remove any created links and
also inform the nfp of this.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the way in which the tunnel neighbour entries
are handled. Previously they were mostly send-and-forget, with
just the destination IP's cached in a list. This update changes
to a scheme where the neighbour entry information is stored in
a hash table.
The reason for this is that the neighbour table will now also
be used on the decapsulation path, whereas previously it was
only used for encapsulation. We need to save more of the neighbour
information in order to link them with flower flows in follow
up patches.
Updating of the neighbour table is now also handled by the same
function, instead of separate *_write_neigh_vX functions.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:44 +0000 (14:43 +0900)]
nfp: flower: update nfp_tun_neigh structs
Prepare for more rework in following patches by updating
the existing nfp_neigh_structs. The update allows for
the same headers to be used for both old and new firmware,
with a slight length adjustment when sending the control message
to the firmware.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:43 +0000 (14:43 +0900)]
nfp: flower: fixup ipv6/ipv4 route lookup for neigh events
When a callback is received to invalidate a neighbour entry
there is no need to try and populate any other flow information.
Only the flowX->daddr information is needed as lookup key to delete
an entry from the NFP neighbour table. Fix this by only doing the
lookup if the callback is for a new entry.
As part of this cleanup remove the setting of flow6.flowi6_proto, as
this is not needed either, it looks to be a possible leftover from a
previous implementation.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:42 +0000 (14:43 +0900)]
nfp: flower: enforce more strict pre_tun checks
Make sure that the rule also matches on source MAC address. On top
of that also now save the src and dst MAC addresses similar to how
vlan_tci is saved - this will be used in later comparisons with
neighbour entries. Indicate if the flow matched on ipv4 or ipv6.
Populate the vlan_tpid field that got added to the pre_run_rule
struct as well.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:41 +0000 (14:43 +0900)]
nfp: flower: add/remove predt_list entries
Add calls to add and remove flows to the predt_table. This very simply
just allocates and add a new pretun entry if detected as such, and
removes it when encountered on a delete flow.
Compatibility for older firmware is kept in place through the
DECAP_V2 feature bit.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Louis Peens [Thu, 5 May 2022 05:43:40 +0000 (14:43 +0900)]
nfp: flower: add infrastructure for pre_tun rework
The previous implementation of using a pre_tun_table for decap has
some limitations, causing flows to end up unoffloaded when in fact
we are able to offload them. This is because the pre_tun_table does
not have enough matching resolution. The next step is to instead make
use of the neighbour table which already exists for the encap direction.
This patch prepares for this by:
- Moving nfp_tun_neigh/_v6 to main.h.
- Creating two new "wrapping" structures, one to keep track of neighbour
entries (previously they were send-and-forget), and another to keep
track of pre_tun flows.
- Create a new list in nfp_flower_priv to keep track of pre_tunnel flows
- Create a new table in nfp_flower_priv to keep track of next neighbour
entries
- Initialising and destroying these new list/tables
- Extending nfp_fl_payload->pre_tun_rule to save more information for
future use.
Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 6 May 2022 09:50:05 +0000 (10:50 +0100)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-05-05
This series contains updates to ice driver only.
Wan Jiabing converts an open coded min selection to min_t().
Maciej commonizes on a single find VSI function and removes the
duplicated implementation.
Wojciech adjusts the return value when exceeding ICE_MAX_CHAIN_WORDS to,
a more appropriate, -ENOSPC and allows for the error to be propagated.
Michal adds support for ndo_get_devlink_port().
Jake does some cleanup related to virtualization code. Mainly involving
function header comments and wording changes. NULL checks are added to
ice_get_vf_vsi() calls in order to prevent static analysis tools from
complaining that a NULL value could be dereferenced.
---
v2: Dropped patch 1: "ice: Add support for classid based queue selection"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This series improves MPTCP receive window compliance with RFC 8684 and
helps increase throughput on high-speed links. Note that patch 3 makes a
change in tcp_output.c
For the details, Paolo says:
I've been chasing bad/unstable performance with multiple subflows
on very high speed links.
It looks like the root cause is due to the current mptcp-level
congestion window handling. There are apparently a few different
sub-issues:
- the rcv_wnd is not effectively shared on the tx side, as each
subflow takes in account only the value received by the underlaying
TCP connection. This is addressed in patch 1/5
- The mptcp-level offered wnd right edge is currently allowed to shrink.
Reading section 3.3.4.:
"""
The receive window is relative to the DATA_ACK. As in TCP, a
receiver MUST NOT shrink the right edge of the receive window (i.e.,
DATA_ACK + receive window). The receiver will use the data sequence
number to tell if a packet should be accepted at the connection
level.
"""
I read the above as we need to reflect window right-edge tracking
on the wire, see patch 4/5.
- The offered window right edge tracking can happen concurrently on
multiple subflows, but there is no mutex protection. We need an
additional atomic operation - still patch 4/5
This series additionally bumps a few new MIBs to track all the above
(ensure/observe that the suspected races actually take place).
I could not access again the host where the issue was so
noticeable, still in the current setup the tput changes from
[6-18] Gbps to 19Gbps very stable.
====================
Paolo Abeni [Wed, 4 May 2022 21:54:08 +0000 (14:54 -0700)]
mptcp: add more offered MIBs counter
Track the exceptional handling of MPTCP-level offered window
with a few more counters for observability.
Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / kernel.git / log