net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.
So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.
Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side
Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.
iperf3 results before the change:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender
[ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver
iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver
Fixes: b0a17773da22e4 ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Shmulik Ladkani [Wed, 25 Dec 2019 08:51:01 +0000 (10:51 +0200)]
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
There's no skb_pull performed when a mirred action is set at egress of a
mac device, with a target device/action that expects skb->data to point
at the network header.
As a result, either the target device is errornously given an skb with
data pointing to the mac (egress case), or the net stack receives the
skb with data pointing to the mac (ingress case).
E.g:
# tc qdisc add dev eth9 root handle 1: prio
# tc filter add dev eth9 parent 1: prio 9 protocol ip handle 9 basic \
action mirred egress redirect dev tun0
(tun0 is a tun device. result: tun0 errornously gets the eth header
instead of the iph)
Revise the push/pull logic of tcf_mirred_act() to not rely on the
skb_at_tc_ingress() vs tcf_mirred_act_wants_ingress() comparison, as it
does not cover all "pull" cases.
Instead, calculate whether the required action on the target device
requires the data to point at the network header, and compare this to
whether skb->data points to network header - and make the push/pull
adjustments as necessary.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Shmulik Ladkani <sladkani@proofpoint.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 23 Dec 2019 19:13:24 +0000 (11:13 -0800)]
net_sched: sch_fq: properly set sk->sk_pacing_status
If fq_classify() recycles a struct fq_flow because
a socket structure has been reallocated, we do not
set sk->sk_pacing_status immediately, but later if the
flow becomes detached.
This means that any flow requiring pacing (BBR, or SO_MAX_PACING_RATE)
might fallback to TCP internal pacing, which requires a per-socket
high resolution timer, and therefore more cpu cycles.
Fixes: c1fd2cc7e149 ("tcp: internal implementation for pacing") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 26 Dec 2019 23:27:15 +0000 (15:27 -0800)]
Merge branch 'bnx2x-Bug-fixes'
Manish Chopra says:
====================
bnx2x: Bug fixes
This series has changes in the area of vlan resources
management APIs to fix fw assert issue reported in max
vlan configuration testing over the PF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 23 Dec 2019 18:23:09 +0000 (10:23 -0800)]
bnx2x: Fix accounting of vlan resources among the PFs
While testing max vlan configuration on the PF, firmware gets
assert as driver was configuring number of vlans more than what
is supported per port/engine, it was figured out that there is an
implicit vlan (hidden default vlan consuming hardware cam entry resource)
which is configured default for all the clients (PF/VFs) on client_init
ramrod by the adapter implicitly, so when allocating resources among the
PFs this implicit vlan should be considered or total vlan entries should
be reduced by one to accommodate that default/implicit vlan entry.
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Mon, 23 Dec 2019 18:23:08 +0000 (10:23 -0800)]
bnx2x: Use appropriate define for vlan credit
Although it has same value as MAX_MAC_CREDIT_E2,
use MAX_VLAN_CREDIT_E2 appropriately.
Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
If CONFIG_OF_MDIO=n:
drivers/net/phy/mdio_bus.c:23:
include/linux/of_mdio.h:58:13: warning: ‘of_mdiobus_child_is_phy’ defined but not used [-Wunused-function]
static bool of_mdiobus_child_is_phy(struct device_node *child)
^~~~~~~~~~~~~~~~~~~~~~~
Fix this by adding the missing "inline" keyword.
Fixes: 8bd7e465f9d4d3b5 ("of: mdio: export of_mdiobus_child_is_phy") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Mon, 23 Dec 2019 08:06:10 +0000 (10:06 +0200)]
net: phy: aquantia: add suspend / resume ops for AQR105
The suspend/resume code for AQR107 works on AQR105 too.
This patch fixes issues with the partner not seeing the link down
when the interface using AQR105 is brought down.
Fixes: 02d75e4b3a23 ("net: phy: add driver for aquantia phy") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Mon, 23 Dec 2019 07:39:22 +0000 (09:39 +0200)]
dpaa_eth: fix DMA mapping leak
On the error path some fragments remain DMA mapped. Adding a fix
that unmaps all the fragments. Rework cleanup path to be simpler.
Fixes: ccf131906849 ("dpaa_eth: use page backed rx buffers") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlxfw: Fix out-of-memory error in mfa2 flash burning
The burning process requires to perform internal allocations of large
chunks of memory. This memory doesn't need to be contiguous and can be
safely allocated by vzalloc() instead of kzalloc(). This patch changes
such allocation to avoid possible out-of-memory failure.
Fixes: dc10fdb21829 ("Add the mlxfw module for Mellanox firmware flash process") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Tested-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 26 Dec 2019 00:35:35 +0000 (16:35 -0800)]
Merge branch 'hsr-fix-several-bugs-in-hsr-module'
Taehee Yoo says:
====================
hsr: fix several bugs in hsr module
1. The first patch fixes debugfs warning when it's opened when hsr module
is being removed. debugfs file is opened, it tries to hold .owner module,
but it would print warning messages if it couldn't hold .owner module.
In order to avoid the warning message, this patch makes hsr module does
not set .owner. Unsetting .owner is safe because these are protected by
inode_lock().
2. The second patch fixes wrong error handling of hsr_dev_finalize()
a) hsr_dev_finalize() calls debugfs_create_{dir/file} to create debugfs.
it checks NULL pointer but debugfs don't return NULL so it's wrong code.
b) hsr_dev_finalize() calls register_netdevice(). so if it fails after
register_netdevice(), it should call unregister_netdevice().
But it doesn't.
c) debugfs doesn't affect any actual logic of hsr module.
So, the failure of creating of debugfs could be ignored.
3. The third patch adds hsr root debugfs directory.
When hsr interface is created, it creates debugfs directory in
/sys/kernel/debug/<interface name>.
It's a little bit faulty path because if an interface is the same with
another directory name in the same path, it will fail. If hsr root
directory is existing, the possibility of failure of creating debugfs
file will be reduced.
4. The fourth patch adds debugfs rename routine.
debugfs directory name is the same with hsr interface name.
So hsr interface name is changed, debugfs directory name should be
changed too.
5. The fifth patch fixes a race condition in node list add and del.
hsr nodes are protected by RCU and there is no write side lock.
But node insertions and deletions could be being operated concurrently.
So write side locking is needed.
6. The Sixth patch resets network header
Tap routine is enabled, below message will be printed.
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
hsr module doesn't set network header for supervision frame.
But tap routine validates network header.
If network header wasn't set, it resets and warns about it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Sun, 22 Dec 2019 11:27:08 +0000 (11:27 +0000)]
hsr: reset network header when supervision frame is created
The supervision frame is L2 frame.
When supervision frame is created, hsr module doesn't set network header.
If tap routine is enabled, dev_queue_xmit_nit() is called and it checks
network_header. If network_header pointer wasn't set(or invalid),
it resets network_header and warns.
In order to avoid unnecessary warning message, resetting network_header
is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
tcpdump -nei veth0
Splat looks like:
[ 175.852292][ C3] protocol 88fb is buggy, dev veth0
Fixes: f8baa9c29c38 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Sun, 22 Dec 2019 11:26:54 +0000 (11:26 +0000)]
hsr: fix a race condition in node list insertion and deletion
hsr nodes are protected by RCU and there is no write side lock.
But node insertions and deletions could be being operated concurrently.
So write side locking is needed.
Test commands:
ip netns add nst
ip link add veth0 type veth peer name veth1
ip link add veth2 type veth peer name veth3
ip link set veth1 netns nst
ip link set veth3 netns nst
ip link set veth0 up
ip link set veth2 up
ip link add hsr0 type hsr slave1 veth0 slave2 veth2
ip a a 192.168.100.1/24 dev hsr0
ip link set hsr0 up
ip netns exec nst ip link set veth1 up
ip netns exec nst ip link set veth3 up
ip netns exec nst ip link add hsr1 type hsr slave1 veth1 slave2 veth3
ip netns exec nst ip a a 192.168.100.2/24 dev hsr1
ip netns exec nst ip link set hsr1 up
for i in {0..9}
do
for j in {0..9}
do
for k in {0..9}
do
for l in {0..9}
do
arping 192.168.100.2 -I hsr0 -s 00:01:3$i:4$j:5$k:6$l -c1 &
done
done
done
done
Reported-by: syzbot+3924327f9ad5f4d2b343@syzkaller.appspotmail.com Fixes: f8baa9c29c38 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Sun, 22 Dec 2019 11:26:39 +0000 (11:26 +0000)]
hsr: rename debugfs file when interface name is changed
hsr interface has own debugfs file, which name is same with interface name.
So, interface name is changed, debugfs file name should be changed too.
Fixes: f194a197c0dd ("net: hsr: add debugfs support for display node list") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Sun, 22 Dec 2019 11:26:27 +0000 (11:26 +0000)]
hsr: add hsr root debugfs directory
In current hsr code, when hsr interface is created, it creates debugfs
directory /sys/kernel/debug/<interface name>.
If there is same directory or file name in there, it fails.
In order to reduce possibility of failure of creation of debugfs,
this patch adds root directory.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
Before this patch:
/sys/kernel/debug/hsr0/node_table
After this patch:
/sys/kernel/debug/hsr/hsr0/node_table
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Sun, 22 Dec 2019 11:26:15 +0000 (11:26 +0000)]
hsr: fix error handling routine in hsr_dev_finalize()
hsr_dev_finalize() is called to create new hsr interface.
There are some wrong error handling codes.
1. wrong checking return value of debugfs_create_{dir/file}.
These function doesn't return NULL. If error occurs in there,
it returns error pointer.
So, it should check error pointer instead of NULL.
2. It doesn't unregister interface if it fails to setup hsr interface.
If it fails to initialize hsr interface after register_netdevice(),
it should call unregister_netdevice().
3. Ignore failure of creation of debugfs
If creating of debugfs dir and file is failed, creating hsr interface
will be failed. But debugfs doesn't affect actual logic of hsr module.
So, ignoring this is more correct and this behavior is more general.
Fixes: aefd34382d1c ("net/hsr: Use list_head (and rcu) instead of array for slave devices.") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Sun, 22 Dec 2019 11:25:27 +0000 (11:25 +0000)]
hsr: avoid debugfs warning message when module is remove
When hsr module is being removed, debugfs_remove() is called to remove
both debugfs directory and file.
When module is being removed, module state is changed to
MODULE_STATE_GOING then exit() is called.
At this moment, module couldn't be held so try_module_get()
will be failed.
debugfs's open() callback tries to hold the module if .owner is existing.
If it fails, warning message is printed.
In order to avoid the warning message, this patch makes hsr module does
not set .owner. Unsetting .owner is safe because these are protected by
inode_lock().
Test commands:
#SHELL1
ip link add dummy0 type dummy
ip link add dummy1 type dummy
while :
do
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
modprobe -rv hsr
done
#SHELL2
while :
do
cat /sys/kernel/debug/hsr0/node_table
done
Fixes: f194a197c0dd ("net: hsr: add debugfs support for display node list") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 25 Dec 2019 06:41:07 +0000 (22:41 -0800)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-12-23
please apply the following patch series for qeth to your net tree.
This brings two fixes for errors during device initialization, deals with
several issues in the vnicc control code, and adds a missing lock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 23 Dec 2019 14:03:26 +0000 (15:03 +0100)]
s390/qeth: fix initialization on old HW
I stumbled over an old OSA model that claims to support DIAG_ASSIST,
but then rejects the cmd to query its DIAG capabilities.
In the old code this was ok, as the returned raw error code was > 0.
Now that we translate the raw codes to errnos, the "rc < 0" causes us
to fail the initialization of the device.
The fix is trivial: don't bail out when the DIAG query fails. Such an
error is not critical, we can still use the device (with a slightly
reduced set of features).
Fixes: 507c62c6067d ("s390/qeth: convert remaining legacy cmd callbacks") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandra Winter [Mon, 23 Dec 2019 14:03:25 +0000 (15:03 +0100)]
s390/qeth: vnicc Fix init to default
During vnicc_init wanted_char should be compared to cur_char and not
to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce
the default values as desired values.
Note, that it is expected, that a card comes online with default values.
This patch was tested with private card firmware.
Fixes: 7cb7f614c986 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandra Winter [Mon, 23 Dec 2019 14:03:24 +0000 (15:03 +0100)]
s390/qeth: Fix vnicc_is_in_use if rx_bcast not set
Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: 7cb7f614c986 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandra Winter [Mon, 23 Dec 2019 14:03:23 +0000 (15:03 +0100)]
s390/qeth: fix false reporting of VNIC CHAR config failure
Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.
The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.
For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.
So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.
Fixes: 7cb7f614c986 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 23 Dec 2019 14:03:22 +0000 (15:03 +0100)]
s390/qeth: lock the card while changing its hsuid
qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't
take the conf_mutex to ensure that the card stays in this state while
being reconfigured.
Rework the code to take this lock, and drop a redundant state check in a
helper function.
Fixes: 27a8eccc0d1c ("qeth: add support for af_iucv HiperSockets transport") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Mon, 23 Dec 2019 14:03:21 +0000 (15:03 +0100)]
s390/qeth: fix qdio teardown after early init error
qeth_l?_set_online() goes through a number of initialization steps, and
on any error uses qeth_l?_stop_card() to tear down the residual state.
The first initialization step is qeth_core_hardsetup_card(). When this
fails after having established a QDIO context on the device
(ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't
shut down this QDIO context again (since the card state hasn't
progressed from DOWN at this stage).
Even worse, we then call qdio_free() as final teardown step to free the
QDIO data structures - while some of them are still hooked into wider
QDIO infrastructure such as the IRQ list. This is inevitably followed by
use-after-frees and other nastyness.
Fix this by unconditionally calling qeth_qdio_clear_card() to shut down
the QDIO context, and also to halt/clear any pending activity on the
various IO channels.
Remove the naive attempt at handling the teardown in
qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it
properly now in the wider teardown code.
Fixes: a5a090d6ef88 ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
disable neigh update for tunnels during pmtu update
When we setup a pair of gretap, ping each other and create neighbour cache.
Then delete and recreate one side. We will never be able to ping6 to the new
created gretap.
The reason is when we ping6 remote via gretap, we will call like
As the confirmed time updated, in neigh_timer_handler() the check for
NUD_DELAY confirm time will pass and the neigh state will back to
NUD_REACHABLE. So the old/wrong mac address will be used again.
If we do not update the confirmed time, the neigh state will go to
neigh->nud_state = NUD_PROBE; then go to NUD_FAILED and re-create the
neigh later, which is what IPv4 does.
We couldn't remove the ip6_confirm_neigh() directly as we still need it
for TCP flows. To fix it, we have to pass a bool parameter to
dst_ops.update_pmtu() and only disable neighbor update for tunnels.
v5: No code change, upate some commits description
v4: No code change, upate some commits description
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sun, 22 Dec 2019 02:51:16 +0000 (10:51 +0800)]
net/dst: do not confirm neighbor for vxlan and geneve pmtu update
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
So disable the neigh confirm for vxlan and geneve pmtu update.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: 6daedd25f623 ("vxlan: update skb dst pmtu on tx path") Fixes: 83aa5a183b06 ("geneve: update skb dst pmtu on tx path") Reviewed-by: Guillaume Nault <gnault@redhat.com> Tested-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sun, 22 Dec 2019 02:51:15 +0000 (10:51 +0800)]
sit: do not confirm neighbor when do pmtu update
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sun, 22 Dec 2019 02:51:14 +0000 (10:51 +0800)]
vti: do not confirm neighbor when do pmtu update
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although vti and vti6 are immune to this problem because they are IFF_NOARP
interfaces, as Guillaume pointed. There is still no sense to confirm neighbour
here.
v5: Update commit description.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sun, 22 Dec 2019 02:51:13 +0000 (10:51 +0800)]
tunnel: do not confirm neighbor when do pmtu update
When do tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No Change.
v4: Update commit description
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: 374abf25e969 ("net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP") Reviewed-by: Guillaume Nault <gnault@redhat.com> Tested-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sun, 22 Dec 2019 02:51:12 +0000 (10:51 +0800)]
net/dst: add new function skb_dst_update_pmtu_no_confirm
Add a new function skb_dst_update_pmtu_no_confirm() for callers who need
update pmtu but should not do neighbor confirm.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sun, 22 Dec 2019 02:51:11 +0000 (10:51 +0800)]
gtp: do not confirm neighbor when do pmtu update
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although GTP only support ipv4 right now, and __ip_rt_update_pmtu() does not
call dst_confirm_neigh(), we still set it to false to keep consistency with
IPv6 code.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sun, 22 Dec 2019 02:51:10 +0000 (10:51 +0800)]
ip6_gre: do not confirm neighbor when do pmtu update
When we do ipv6 gre pmtu update, we will also do neigh confirm currently.
This will cause the neigh cache be refreshed and set to REACHABLE before
xmit.
But if the remote mac address changed, e.g. device is deleted and recreated,
we will not able to notice this and still use the old mac address as the neigh
cache is REACHABLE.
Fix this by disable neigh confirm when do pmtu update
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Sun, 22 Dec 2019 02:51:09 +0000 (10:51 +0800)]
net: add bool confirm_neigh parameter for dst_ops.update_pmtu
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net> Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 25 Dec 2019 00:12:47 +0000 (16:12 -0800)]
Merge tag 'rxrpc-fixes-20191220' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fixes
Here are a couple of bugfixes plus a patch that makes one of the bugfixes
easier:
(1) Move the ping and mutex unlock on a new call from rxrpc_input_packet()
into rxrpc_new_incoming_call(), which it calls. This means the
lock-unlock section is entirely within the latter function. This
simplifies patch (2).
(2) Don't take the call->user_mutex at all in the softirq path. Mutexes
aren't allowed to be taken or released there and a patch was merged
that caused a warning to be emitted every time this happened. Looking
at the code again, it looks like that taking the mutex isn't actually
necessary, as the value of call->state will block access to the call.
(3) Fix the incoming call path to check incoming calls earlier to reject
calls to RPC services for which we don't have a security key of the
appropriate class. This avoids an assertion failure if YFS tries
making a secure call to the kafs cache manager RPC service.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Fri, 20 Dec 2019 19:24:21 +0000 (11:24 -0800)]
net: dsa: bcm_sf2: Fix IP fragment location and behavior
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 8d74278c0f50 ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The fix on 677cac304ac8 fixed the issued reported there but introduced
another. When the allocation fails within sctp_stream_init() it is
okay/necessary to free the genradix. But it is also called when adding
new streams, from sctp_send_add_streams() and
sctp_process_strreset_addstrm_in() and in those situations it cannot
just free the genradix because by then it is a fully operational
association.
The fix here then is to only free the genradix in sctp_stream_init()
and on those other call sites move on with what it already had and let
the subsequent error handling to handle it.
Tested with the reproducers from this report and the previous one,
with lksctp-tools and sctp-tests.
Reported-by: syzbot+9a1bc632e78a1a98488b@syzkaller.appspotmail.com Fixes: 677cac304ac8 ("sctp: fix memleak on err handling of stream initialization") Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Messina [Thu, 19 Dec 2019 14:08:03 +0000 (15:08 +0100)]
udp: fix integer overflow while computing available space in sk_rcvbuf
When the size of the receive buffer for a socket is close to 2^31 when
computing if we have enough space in the buffer to copy a packet from
the queue to the buffer we might hit an integer overflow.
When an user set net.core.rmem_default to a value close to 2^31 UDP
packets are dropped because of this overflow. This can be visible, for
instance, with failure to resolve hostnames.
This can be fixed by casting sk_rcvbuf (which is an int) to unsigned
int, similarly to how it is done in TCP.
Signed-off-by: Antonio Messina <amessina@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 22 Dec 2019 22:37:40 +0000 (23:37 +0100)]
bpf: Fix precision tracking for unbounded scalars
Anatoly has been fuzzing with kBdysch harness and reported a hang in one
of the outcomes. Upon closer analysis, it turns out that precise scalar
value tracking is missing a few precision markings for unknown scalars:
In the analysis of the second path coming after the successful exit above,
the path is being pruned at line 7. Pruning analysis found that both r0 are
precise P0 and both R1 are non-precise scalars and given prior path with
R1 as non-precise scalar succeeded, this one is therefore safe as well.
However, problem is that given condition at insn 7 in the first run, we only
followed goto and didn't push the other branch for later analysis, we've
never walked the few insns in there and therefore dead-code sanitation
rewrites it as goto pc-1, causing the hang depending on the skb address
hitting these conditions. The issue is that R1 should have been marked as
precise as well such that pruning enforces range check and conluded that new
R1 is not in range of old R1. In insn 4, we mark R1 (skb) as unknown scalar
via __mark_reg_unbounded() but not mark_reg_unbounded() and therefore
regs->precise remains as false.
Back in 28eac819dbea ("bpf: precise scalar_value tracking"), this was not
the case since marking out of __mark_reg_unbounded() had this covered as well.
Once in both are set as precise in 4 as they should have been, we conclude
that given R1 was in prior fall-through path 0x104c1500 and now is completely
unknown, the check at insn 7 concludes that we need to continue walking.
Analysis after the fix:
Linus Torvalds [Sun, 22 Dec 2019 18:59:06 +0000 (10:59 -0800)]
Merge tag 'xfs-5.5-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Fix a few bugs that could lead to corrupt files, fsck complaints, and
filesystem crashes:
- Minor documentation fixes
- Fix a file corruption due to read racing with an insert range
operation.
- Fix log reservation overflows when allocating large rt extents
- Fix a buffer log item flags check
- Don't allow administrators to mount with sunit= options that will
cause later xfs_repair complaints about the root directory being
suspicious because the fs geometry appeared inconsistent
- Fix a non-static helper that should have been static"
* tag 'xfs-5.5-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Make the symbol 'xfs_rtalloc_log_count' static
xfs: don't commit sunit/swidth updates to disk if that would cause repair failures
xfs: split the sunit parameter update into two parts
xfs: refactor agfl length computation function
libxfs: resync with the userspace libxfs
xfs: use bitops interface for buf log item AIL flag check
xfs: fix log reservation overflows when allocating large rt extents
xfs: stabilize insert range start boundary to avoid COW writeback race
xfs: fix Sphinx documentation warning
Linus Torvalds [Sun, 22 Dec 2019 18:41:48 +0000 (10:41 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 bug fixes from Ted Ts'o:
"Ext4 bug fixes, including a regression fix"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: clarify impact of 'commit' mount option
ext4: fix unused-but-set-variable warning in ext4_add_entry()
jbd2: fix kernel-doc notation warning
ext4: use RCU API in debug_print_tree
ext4: validate the debug_want_extra_isize mount option at parse time
ext4: reserve revoke credits in __ext4_new_inode
ext4: unlock on error in ext4_expand_extra_isize()
ext4: optimize __ext4_check_dir_entry()
ext4: check for directory entries too close to block end
ext4: fix ext4_empty_dir() for directories with holes
Linus Torvalds [Sun, 22 Dec 2019 18:36:55 +0000 (10:36 -0800)]
Merge tag 'block-5.5-20191221' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Let's try this one again, this time without the compat_ioctl changes.
We've got those fixed up, but that can go out next week.
This contains:
- block queue flush lockdep annotation (Bart)
- Type fix for bsg_queue_rq() (Bart)
- Three dasd fixes (Stefan, Jan)
- nbd deadlock fix (Mike)
- Error handling bio user map fix (Yang)
- iocost fix (Tejun)
- sbitmap waitqueue addition fix that affects the kyber IO scheduler
(David)"
* tag 'block-5.5-20191221' of git://git.kernel.dk/linux-block:
sbitmap: only queue kyber's wait callback if not already active
block: fix memleak when __blk_rq_map_user_iov() is failed
s390/dasd: fix typo in copyright statement
s390/dasd: fix memleak in path handling error case
s390/dasd/cio: Interpret ccw_device_get_mdc return value correctly
block: Fix a lockdep complaint triggered by request queue flushing
block: Fix the type of 'sts' in bsg_queue_rq()
block: end bio with BLK_STS_AGAIN in case of non-mq devs and REQ_NOWAIT
nbd: fix shutdown and recv work deadlock v2
iocost: over-budget forced IOs should schedule async delay
- Fix scratch register clearing in M-mode (affects nommu users)
- Fix a mismerge on my part that broke the build for
CONFIG_SPARSEMEM_VMEMMAP users
Cleanup:
- Move SiFive L2 cache-related code to drivers/soc, per request"
* tag 'riscv/for-v5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: move sifive_l2_cache.c to drivers/soc
riscv: define vmemmap before pfn_to_page calls
riscv: fix scratch register clearing in M-mode.
riscv: Fix use of undefined config option CONFIG_CONFIG_MMU
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
Jan Stancek [Sun, 22 Dec 2019 12:33:24 +0000 (13:33 +0100)]
pipe: fix empty pipe check in pipe_write()
LTP pipeio_1 test is hanging with v5.5-rc2-385-gb8e382a185eb,
with read side observing empty pipe and sleeping and write
side running out of space and then sleeping as well. In this
scenario there are 5 writers and 1 reader.
Problem is that after pipe_write() reacquires pipe lock, it
re-checks for empty pipe with potentially stale 'head' and
doesn't wake up read side anymore. pipe->tail can advance
beyond 'head', because there are multiple writers.
Use pipe->head for empty pipe check after reacquiring lock
to observe current state.
Testing: With patch, LTP pipeio_1 ran successfully in loop for 1 hour.
Without patch it hanged within a minute.
Paolo Bonzini [Wed, 4 Dec 2019 14:33:35 +0000 (15:33 +0100)]
MAINTAINERS: remove Radim from KVM maintainers
Radim's kernel.org email is bouncing, which I take as a signal that
he is not really able to deal with KVM at this time. Make MAINTAINERS
match the effective value of KVM's bus factor.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
James Hogan [Sat, 21 Dec 2019 15:50:13 +0000 (15:50 +0000)]
MAINTAINERS: Orphan KVM for MIPS
I haven't been active for 18 months, and don't have the hardware set up
to test KVM for MIPS, so mark it as orphaned and remove myself as
maintainer. Hopefully somebody from MIPS can pick this up.
Signed-off-by: James Hogan <jhogan@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: "Radim Krčmář" <rkrcmar@redhat.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: kvm@vger.kernel.org Cc: linux-mips@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yunfeng Ye [Tue, 17 Dec 2019 14:46:49 +0000 (22:46 +0800)]
ext4: fix unused-but-set-variable warning in ext4_add_entry()
Warning is found when compile with "-Wunused-but-set-variable":
fs/ext4/namei.c: In function ‘ext4_add_entry’:
fs/ext4/namei.c:2167:23: warning: variable ‘sbi’ set but not used
[-Wunused-but-set-variable]
struct ext4_sb_info *sbi;
^~~
Fix this by moving the variable @sbi under CONFIG_UNICODE.
Linus Torvalds [Sat, 21 Dec 2019 23:16:56 +0000 (15:16 -0800)]
Merge tag 'trace-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix memory leak on error path of process_system_preds()
- Lock inversion fix with updating tgid recording option
- Fix histogram compare function on big endian machines
- Fix histogram trigger function on big endian machines
- Make trace_printk() irq sync on init for kprobe selftest correctness
* tag 'trace-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix endianness bug in histogram trigger
samples/trace_printk: Wait for IRQ work to finish
tracing: Fix lock inversion in trace_event_enable_tgid_record()
tracing: Have the histogram compare functions convert to u64 first
tracing: Avoid memory leak in process_system_preds()
Linus Torvalds [Sat, 21 Dec 2019 23:12:26 +0000 (15:12 -0800)]
Merge tag 'libnvdimm-fix-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Dan Williams:
"A minor regression fix.
The libnvdimm unit tests were expecting to mock calls to
ioremap_nocache() which disappeared in v5.5-rc1. This fix has appeared
in -next and collided with some cleanups that Christoph has planned
for v5.6, but he will fix up his branch once this goes in.
Summary:
- Restore the operation of the libnvdimm unit tests after the removal
of ioremap_nocache()"
* tag 'libnvdimm-fix-5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
tools/testing/nvdimm: Fix mock support for ioremap
Sven Schnelle [Wed, 18 Dec 2019 07:44:27 +0000 (08:44 +0100)]
tracing: Fix endianness bug in histogram trigger
At least on PA-RISC and s390 synthetic histogram triggers are failing
selftests because trace_event_raw_event_synth() always writes a 64 bit
values, but the reader expects a field->size sized value. On little endian
machines this doesn't hurt, but on big endian this makes the reader always
read zero values.
Link: http://lore.kernel.org/linux-trace-devel/20191218074427.96184-4-svens@linux.ibm.com Cc: stable@vger.kernel.org Fixes: 00a1b9a7a86b6 ("tracing: Add support for 'synthetic' events") Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com> Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
This gives a circular dependency deadlock between trace_types_lock and
event_mutex. To fix this invert the usage of trace_types_lock and
event_mutex in trace_options_core_write(). This keeps the sequence of
lock usage consistent.
Linus Torvalds [Sat, 21 Dec 2019 20:17:14 +0000 (12:17 -0800)]
Merge tag 's390-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix unwinding from irq context of interrupted user process.
- Add purgatory build missing symbols check. That helped to uncover and
fix missing symbols when built with kasan support enabled.
- Couple of ftrace fixes. Avoid broken stack trace and fix recursion
loop in function_graph tracer.
* tag 's390-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ftrace: save traced function caller
s390/unwind: stop gracefully at user mode pt_regs in irq stack
s390/purgatory: do not build purgatory with kcov, kasan and friends
s390/purgatory: Make sure we fail the build if purgatory has missing symbols
s390/ftrace: fix endless recursion in function_graph tracer
Linus Torvalds [Sat, 21 Dec 2019 18:52:10 +0000 (10:52 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: a (rare) PSI crash fix, a CPU affinity related balancing
fix, and a toning down of active migration attempts"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cfs: fix spurious active migration
sched/fair: Fix find_idlest_group() to handle CPU affinity
psi: Fix a division error in psi poll()
sched/psi: Fix sampling error and rare div0 crashes with cgroups and high uptime
Linus Torvalds [Sat, 21 Dec 2019 18:51:00 +0000 (10:51 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: a BTS fix, a PT NMI handling fix, a PMU sysfs fix and an
SRCU annotation"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Add SRCU annotation for pmus list walk
perf/x86/intel: Fix PT PMI handling
perf/x86/intel/bts: Fix the use of page_private()
perf/x86: Fix potential out-of-bounds access
Linus Torvalds [Sat, 21 Dec 2019 18:49:47 +0000 (10:49 -0800)]
Merge tag 'kbuild-fixes-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix warning in out-of-tree 'make clean'
- add READELF variable to the top Makefile
- fix broken builds when LINUX_COMPILE_BY contains a backslash
- fix build warning in kallsyms
- fix NULL pointer access in expr_eq() in Kconfig
- fix missing dependency on rsync in deb-pkg build
- remove ---help--- from documentation
- fix misleading documentation about directory descending
* tag 'kbuild-fixes-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: clarify the difference between obj-y and obj-m w.r.t. descending
kconfig: remove ---help--- from documentation
scripts: package: mkdebian: add missing rsync dependency
kconfig: don't crash on NULL expressions in expr_eq()
scripts/kallsyms: fix offset overflow of kallsyms_relative_base
mkcompile_h: use printf for LINUX_COMPILE_BY
mkcompile_h: git rid of UTS_TRUNCATE from LINUX_COMPILE_{BY,HOST}
x86/boot: kbuild: allow readelf executable to be specified
kbuild: fix 'No such file or directory' warning when cleaning
Masahiro Yamada [Thu, 19 Dec 2019 11:51:00 +0000 (20:51 +0900)]
kbuild: clarify the difference between obj-y and obj-m w.r.t. descending
Kbuild descends into a directory by either 'y' or 'm', but there is an
important difference.
Kbuild combines the built-in objects into built-in.a in each directory.
The built-in.a in the directory visited by obj-y is merged into the
built-in.a in the parent directory. This merge happens recursively
when Kbuild is ascending back towards the top directory, then built-in
objects are linked into vmlinux eventually. This works properly only
when the Makefile specifying obj-y is reachable by the chain of obj-y.
On the other hand, Kbuild does not take built-in.a from the directory
visited by obj-m. This it, all the objects in that directory are
supposed to be modular. If Kbuild descends into a directory by obj-m,
but the Makefile in the sub-directory specifies obj-y, those objects
are just left orphan.
The current statement "Kbuild only uses this information to decide that
it needs to visit the directory" is misleading. Clarify the difference.
Reported-by: Johan Hovold <johan@kernel.org> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Johan Hovold <johan@kernel.org>
Linus Torvalds [Sat, 21 Dec 2019 14:49:41 +0000 (06:49 -0800)]
Merge branch 'parisc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pul parisc fixes from Helge Deller:
"Two build error fixes, one for the soft_offline_page() parameter
change and one for a specific KEXEC/KEXEC_FILE configuration, as well
as a compiler and a linker warning fix"
* 'parisc-5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix compiler warnings in debug_core.c
parisc: soft_offline_page() now takes the pfn
parisc: add missing __init annotation
parisc: fix compilation when KEXEC=n and KEXEC_FILE=y
Linus Torvalds [Sat, 21 Dec 2019 14:24:56 +0000 (06:24 -0800)]
Merge tag 'for-linus-5.5b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains two cleanup patches and a small series for supporting
reloading the Xen block backend driver"
* tag 'for-linus-5.5b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grant-table: remove multiple BUG_ON on gnttab_interface
xen-blkback: support dynamic unbind/bind
xen/interface: re-define FRONT/BACK_RING_ATTACH()
xenbus: limit when state is forced to closed
xenbus: move xenbus_dev_shutdown() into frontend code...
xen/blkfront: Adjust indentation in xlvbd_alloc_gendisk
Linus Torvalds [Sat, 21 Dec 2019 14:17:05 +0000 (06:17 -0800)]
Merge tag 'powerpc-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two weeks worth of accumulated fixes:
- A fix for a performance regression seen on PowerVM LPARs using
dedicated CPUs, caused by our vcpu_is_preempted() returning true
even for idle CPUs.
- One of the ultravisor support patches broke KVM on big endian hosts
in v5.4.
- Our KUAP (Kernel User Access Prevention) code missed allowing
access in __clear_user(), which could lead to an oops or erroneous
SEGV when triggered via PTRACE_GETREGSET.
- Two fixes for the ocxl driver, an open/remove race, and a memory
leak in an error path.
- A handful of other small fixes.
Thanks to: Andrew Donnellan, Christian Zigotzky, Christophe Leroy,
Christoph Hellwig, Daniel Axtens, David Hildenbrand, Frederic Barrat,
Gautham R. Shenoy, Greg Kurz, Ihor Pasichnyk, Juri Lelli, Marcus
Comstedt, Mike Rapoport, Parth Shah, Srikar Dronamraju, Vaidyanathan
Srinivasan"
* tag 'powerpc-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Fix regression on big endian hosts
powerpc: Fix __clear_user() with KUAP enabled
powerpc/pseries/cmm: fix managed page counts when migrating pages between zones
powerpc/8xx: fix bogus __init on mmu_mapin_ram_chunk()
ocxl: Fix potential memory leak on context creation
powerpc/irq: fix stack overflow verification
powerpc: Ensure that swiotlb buffer is allocated from low memory
powerpc/shared: Use static key to detect shared processor
powerpc/vcpu: Assume dedicated processors as non-preempt
ocxl: Fix concurrent AFU open and device removal
Linus Torvalds [Sat, 21 Dec 2019 14:04:12 +0000 (06:04 -0800)]
Merge branch 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 RAS fixes from Borislav Petkov:
"Three urgent RAS fixes for the AMD side of things:
- initialize struct mce.bank so that calculated error severity on AMD
SMCA machines is correct
- do not send IPIs early during bank initialization, when interrupts
are disabled
- a fix for when only a subset of MCA banks are enabled, which led to
boot hangs on some new AMD CPUs"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix possibly incorrect severity calculation on AMD
x86/MCE/AMD: Allow Reserved types to be overwritten in smca_banks[]
x86/MCE/AMD: Do not use rdmsr_safe_on_cpu() in smca_configure()
Linus Torvalds [Sat, 21 Dec 2019 13:55:35 +0000 (05:55 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One core framework fix to walk the orphan list and match up clks to
parents when clk providers register the DT provider after registering
all their clks (as they should).
Then a handful of driver fixes for the qcom, imx, and at91 drivers.
The driver fixes are relatively small fixes for incorrect register
settings or missing locks causing race conditions"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: Avoid SMMU/cx gdsc corner cases
clk: qcom: gcc-sc7180: Fix setting flag for votable GDSCs
clk: Move clk_core_reparent_orphans() under CONFIG_OF
clk: at91: fix possible deadlock
clk: walk orphan list on clock provider registration
clk: imx: pll14xx: fix clk_pll14xx_wait_lock
clk: imx: clk-imx7ulp: Add missing sentinel of ulp_div_table
clk: imx: clk-composite-8m: add lock to gate/mux
sfc: Include XDP packet headroom in buffer step size.
Correct a mismatch between rx_page_buf_step and the actual step size
used when filling buffer pages.
This patch fixes the page overrun that occured when the MTU was set to
anything bigger than 1692.
Fixes: 2e6b0faad9d7 ("sfc: allocate channels for XDP tx queues") Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Fri, 20 Dec 2019 16:26:40 +0000 (16:26 +0000)]
sfc: fix channel allocation with brute force
It was possible for channel allocation logic to get confused between what
it had and what it wanted, and end up trying to use the same channel for
both PTP and regular TX. This led to a kernel panic:
BUG: unable to handle page fault for address: 0000000000047635
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.4.0-rc3-ehc14+ #900
Hardware name: Dell Inc. PowerEdge R710/0M233H, BIOS 6.4.0 07/23/2013
RIP: 0010:native_queued_spin_lock_slowpath+0x188/0x1e0
Code: f3 90 48 8b 32 48 85 f6 74 f6 eb e8 c1 ee 12 83 e0 03 83 ee 01 48 c1 e0 05 48 63 f6 48 05 c0 98 02 00 48 03 04 f5 a0 c6 ed 81 <48> 89 10 8b 42 08 85 c0 75 09 f3 90 8b 42 08 85 c0 74 f7 48 8b 32
RSP: 0018:ffffc90000003d28 EFLAGS: 00010006
RAX: 0000000000047635 RBX: 0000000000000246 RCX: 0000000000040000
RDX: ffff888627a298c0 RSI: 0000000000003ffe RDI: ffff88861f6b8dd4
RBP: ffff8886225c6e00 R08: 0000000000040000 R09: 0000000000000000
R10: 0000000616f080c6 R11: 00000000000000c0 R12: ffff88861f6b8dd4
R13: ffffc90000003dc8 R14: ffff88861942bf00 R15: ffff8886150f2000
FS: 0000000000000000(0000) GS:ffff888627a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000047635 CR3: 000000000200a000 CR4: 00000000000006f0
Call Trace:
<IRQ>
_raw_spin_lock_irqsave+0x22/0x30
skb_queue_tail+0x1b/0x50
sock_queue_err_skb+0x9d/0xf0
__skb_complete_tx_timestamp+0x9d/0xc0
efx_dequeue_buffer+0x126/0x180 [sfc]
efx_xmit_done+0x73/0x1c0 [sfc]
efx_ef10_ev_process+0x56a/0xfe0 [sfc]
? tick_sched_do_timer+0x60/0x60
? timerqueue_add+0x5d/0x70
? enqueue_hrtimer+0x39/0x90
efx_poll+0x111/0x380 [sfc]
? rcu_accelerate_cbs+0x50/0x160
net_rx_action+0x14a/0x400
__do_softirq+0xdd/0x2d0
irq_exit+0xa0/0xb0
do_IRQ+0x53/0xe0
common_interrupt+0xf/0xf
</IRQ>
In the long run we intend to rewrite the channel allocation code, but for
'net' fix this by allocating extra_channels, and giving them TX queues,
even if we do not in fact need them (e.g. on NICs without MAC TX
timestamping), and thereby using simpler logic to assign the channels
once they're allocated.
Fixes: 2e6b0faad9d7 ("sfc: allocate channels for XDP tx queues") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When storing a pointer to a dst_metrics structure in dst_entry._metrics,
two flags are added in the least significant bits of the pointer value.
Hence this assumes all pointers to dst_metrics structures have at least
4-byte alignment.
However, on m68k, the minimum alignment of 32-bit values is 2 bytes, not
4 bytes. Hence in some kernel builds, dst_default_metrics may be only
2-byte aligned, leading to obscure boot warnings like:
Fix this by forcing 4-byte alignment of all dst_metrics structures.
Fixes: 011fc68c0bd2b4fa ("ipv6: do not overwrite inetpeer metrics prematurely") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 20 Dec 2019 07:08:06 +0000 (15:08 +0800)]
selftests: pmtu: fix init mtu value in description
There is no a_r3, a_r4 in the testing topology.
It should be b_r1, b_r2. Also b_r1 mtu is 1400 and b_r2 mtu is 1500.
Fixes: 10460ed651be ("selftests: pmtu: add basic IPv4 and IPv6 PMTU tests") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 20 Dec 2019 02:28:10 +0000 (18:28 -0800)]
hv_netvsc: Fix unwanted rx_table reset
In existing code, the receive indirection table, rx_table, is in
struct rndis_device, which will be reset when changing MTU, ringparam,
etc. User configured receive indirection table values will be lost.
To fix this, move rx_table to struct net_device_context, and check
netif_is_rxfh_configured(), so rx_table will be set to default only
if no user configured value.
Fixes: 3807eedf7471 ("netvsc: allow get/set of RSS indirection table") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 19 Dec 2019 23:24:52 +0000 (23:24 +0000)]
net: phy: ensure that phy IDs are correctly typed
PHY IDs are 32-bit unsigned quantities. Ensure that they are always
treated as such, and not passed around as "int"s.
Fixes: f1807410f434 ("net: phy: check return code when requesting PHY driver module") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 19 Dec 2019 23:24:47 +0000 (23:24 +0000)]
mod_devicetable: fix PHY module format
When a PHY is probed, if the top bit is set, we end up requesting a
module with the string "mdio:-10101110000000100101000101010001" -
the top bit is printed to a signed -1 value. This leads to the module
not being loaded.
Fix the module format string and the macro generating the values for
it to ensure that we only print unsigned types and the top bit is
always 0/1. We correctly end up with
"mdio:10101110000000100101000101010001".
Fixes: 0553d60146ae ("phylib: Support phy module autoloading") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Thu, 19 Dec 2019 18:35:16 +0000 (10:35 -0800)]
qede: Disable hardware gro when xdp prog is installed
commit d51699ed2e62 ("qede: Use NETIF_F_GRO_HW.") introduced
a regression in driver that when xdp program is installed on
qede device, device's aggregation feature (hardware GRO) is not
getting disabled, which is unexpected with xdp.
Fixes: d51699ed2e62 ("qede: Use NETIF_F_GRO_HW.") Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
ena: fixes of interrupt moderation bugs
Differences from V1:
1. Updated default tx interrupt moderation to 64us
2. Added "Fixes:" tags.
3. Removed cosmetic changes that are not relevant for these bug fixes
This patchset includes a couple of fixes of bugs in the implemenation of
interrupt moderation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
expected output: rx-usecs 128
actual output: rx-usecs 0
Reason for issue:
In stage 3, ethtool userspace calls first the ena_get_coalesce() handler
to get the current value of all properties, and then the ena_set_coalesce()
handler. When ena_get_coalesce() is called the adaptive interrupt
moderation is still on. There is an if in the code that returns the
rx_coalesce_usecs only if the adaptive interrupt moderation is off.
And since it is still on, rx_coalesce_usecs is not set, meaning it
stays 0.
Solution to issue:
Remove this if static interrupt moderation intervals have nothing to do
with dynamic ones.
expected output: rx-usecs 128
actual output: rx-usecs 0
Reason for issue:
In stage 2, when ena_set_coalesce() is called, the handler tests if
rx adaptive interrupt moderation is on, and if it is, it returns before
getting to the part in the function that sets the rx non-adaptive
interrupt moderation interval.
Solution to issue:
Remove the return from the function when rx adaptive interrupt moderation
is on.
Also cleaned up the fixed code in ena_set_coalesce by grouping together
adaptive interrupt moderation toggling, and using && instead of nested
ifs.
Fixes: b49e5cf0308f ("net: ena: reimplement set/get_coalesce()") Fixes: 4a1b99ca9000 ("net: ena: fix retrieval of nonadaptive interrupt moderation intervals") Fixes: e59074db59c6 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Current default non-adaptive tx interrupt moderation interval is 196 us.
This value is too high and might cause the tx queue to fill up.
In this commit we set the default non-adaptive tx interrupt moderation
interval to 64 us in order to:
1. Reduce the probability of the queue filling-up (when compared to the
current default value of 196 us).
2. Reduce unnecessary tx interrupt overhead (which happens if we set the
default tx interval to 0).
We determined experimentally that 64 us is an optimal value that
reduces interrupt rate by more than 20% without affecting performance.
Fixes: e59074db59c6 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul [Thu, 19 Dec 2019 11:51:13 +0000 (12:51 +0100)]
net/smc: unregister ib devices in reboot_event
In the reboot_event handler, unregister the ib devices and enable
the IB layer to release the devices before the reboot.
Fixes: 5895fbecde02 ("net/smc: guarantee removal of link groups in reboot") Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: platform: Fix MDIO init for platforms without PHY
The current implementation of "stmmac_dt_phy" function initializes
the MDIO platform bus data, even in the absence of PHY. This fix
will skip MDIO initialization if there is no PHY present.
Fixes: dcaf3bd ("net: stmmac: Convert to phylink and remove phylib logic") Acked-by: Jayati Sahu <jayati.sahu@samsung.com> Signed-off-by: Sriram Dash <sriram.dash@samsung.com> Signed-off-by: Padmanabhan Rajanbabu <p.rajanbabu@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
When a frame with NULL DSAP is received, llc_station_rcv is called.
In turn, llc_stat_ev_rx_null_dsap_xid_c is called to check if it is a NULL
XID frame. The return statement of llc_stat_ev_rx_null_dsap_xid_c returns 1
when the incoming frame is not a NULL XID frame and 0 otherwise. Hence, a
NULL XID response is returned unexpectedly, e.g. when the incoming frame is
a NULL TEST command.
To fix the error, simply remove the conditional operator.
A similar error in llc_stat_ev_rx_null_dsap_test_c is also fixed.
Signed-off-by: Chan Shu Tak, Alex <alexchan@task.com.hk> Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-modification code:
int hip04_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev)
{
[...]
[1] priv->tx_head = TX_NEXT(tx_head);
[2] count++;
[3] netdev_sent_queue(ndev, skb->len);
[...]
}
An rx interrupt occurs if hip04_mac_start_xmit just executes to the line 2,
tx_head has been updated, but corresponding 'skb->len' has not been
added to dql_queue.
And then
hip04_mac_interrupt->__napi_schedule->hip04_rx_poll->hip04_tx_reclaim
In hip04_tx_reclaim, because tx_head has been updated,
bytes_compl will plus an additional "skb-> len"
which has not been added to dql_queue. And then
trigger the BUG_ON(bytes_compl > num_queued - dql->num_completed).
To solve the problem described above, we put
"netdev_sent_queue(ndev, skb->len);"
before
"priv->tx_head = TX_NEXT(tx_head);"
Fixes: bf77431c428e ("net: hisilicon: new hip04 ethernet driver") Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove special taglen define KSZ8795_INGRESS_TAG_LEN
and use generic KSZ_INGRESS_TAG_LEN instead.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 21 Dec 2019 05:00:28 +0000 (21:00 -0800)]
Merge branch 's390-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-12-18
please apply the following patch series to your net tree.
This brings two fixes for initialization / teardown issues, and one
ENOTSUPP cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Dec 2019 15:32:28 +0000 (16:32 +0100)]
s390/qeth: don't return -ENOTSUPP to userspace
ENOTSUPP is not uapi, use EOPNOTSUPP instead.
Fixes: e62d2b0f85e4 ("qeth: Add new priority queueing options") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Dec 2019 15:32:27 +0000 (16:32 +0100)]
s390/qeth: fix promiscuous mode after reset
When managing the promiscuous mode during an RX modeset, qeth caches the
current HW state to avoid repeated programming of the same state on each
modeset.
But while tearing down a device, we forget to clear the cached state. So
when the device is later set online again, the initial RX modeset
doesn't program the promiscuous mode since we believe it is already
enabled.
Fix this by clearing the cached state in the tear-down path.
Note that for the SBP variant of promiscuous mode, this accidentally
works right now because we unconditionally restore the SBP role while
re-initializing.
Fixes: a5a090d6ef88 ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 18 Dec 2019 15:32:26 +0000 (16:32 +0100)]
s390/qeth: handle error due to unsupported transport mode
Along with z/VM NICs, there's additional device types that only support
a specific transport mode (eg. external-bridged IQD).
Identify the corresponding error code, and raise a fitting error message
so that the user knows to adjust their device configuration.
On top of that also fix the subsequent error path, so that the rejected
cmd doesn't need to wait for a timeout but gets cancelled straight away.
Fixes: a5a090d6ef88 ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Jeffery [Tue, 17 Dec 2019 16:00:24 +0000 (11:00 -0500)]
sbitmap: only queue kyber's wait callback if not already active
Under heavy loads where the kyber I/O scheduler hits the token limits for
its scheduling domains, kyber can become stuck. When active requests
complete, kyber may not be woken up leaving the I/O requests in kyber
stuck.
This stuck state is due to a race condition with kyber and the sbitmap
functions it uses to run a callback when enough requests have completed.
The running of a sbt_wait callback can race with the attempt to insert the
sbt_wait. Since sbitmap_del_wait_queue removes the sbt_wait from the list
first then sets the sbq field to NULL, kyber can see the item as not on a
list but the call to sbitmap_add_wait_queue will see sbq as non-NULL. This
results in the sbt_wait being inserted onto the wait list but ws_active
doesn't get incremented. So the sbitmap queue does not know there is a
waiter on a wait list.
Since sbitmap doesn't think there is a waiter, kyber may never be
informed that there are domain tokens available and the I/O never advances.
With the sbt_wait on a wait list, kyber believes it has an active waiter
so cannot insert a new waiter when reaching the domain's full state.
This race can be fixed by only adding the sbt_wait to the queue if the
sbq field is NULL. If sbq is not NULL, there is already an action active
which will trigger the re-running of kyber. Let it run and add the
sbt_wait to the wait list if still needing to wait.
Reviewed-by: Omar Sandoval <osandov@fb.com> Signed-off-by: David Jeffery <djeffery@redhat.com> Reported-by: John Pittman <jpittman@redhat.com> Tested-by: John Pittman <jpittman@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rahul Lakkireddy [Wed, 18 Dec 2019 03:49:29 +0000 (09:19 +0530)]
cxgb4: fix refcount init for TC-MQPRIO offload
Properly initialize refcount to 1 when hardware queue arrays for
TC-MQPRIO offload have been freshly allocated. Otherwise, following
warning is observed. Also fix up error path to only free hardware
queue arrays when refcount reaches 0.
v2:
- Move the refcount_set() closer to where the hardware queue arrays
are being allocated.
- Fix up error path to only free hardware queue arrays when refcount
reaches 0.
Fixes: 62b24e7b11c6 ("cxgb4: add ETHOFLD hardware queue support") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 20 Dec 2019 21:36:49 +0000 (13:36 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Leftover put_cpu() in the perf/smmuv3 error path.
- Add Hisilicon TSV110 to spectre-v2 safe list
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: cpu_errata: Add Hisilicon TSV110 to spectre-v2 safe list
perf/smmuv3: Remove the leftover put_cpu() in error path
Linus Torvalds [Fri, 20 Dec 2019 21:33:50 +0000 (13:33 -0800)]
Merge tag 'drm-fixes-2019-12-21' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Probably the last one before Christmas, I'll see if there is much
demand over next few weeks for more fixes, I expect it'll be quiet
enough.
This has one exynos fix, and a bunch of i915 core and i915 GVT fixes.
Summary:
exynos:
- component delete fix
i915:
- Fix to drop an unused and harmful display W/A
- Fix to define EHL power wells independent of ICL
- Fix for priority inversion on bonded requests
- Fix in mmio offset calculation of DSB instance
- Fix memory leak from get_task_pid when banning clients
- Fixes to avoid dereference of uninitialized ops in dma_fence
tracing and keep reference to execbuf object until submitted.
- vGPU state setting locking fix (Zhenyu)
- Fix vGPU display dmabuf as read-only (Zhenyu)
- Properly handle vGPU display dmabuf page pin when rendering (Tina)
- Fix one guest boot warning to handle guc reset state (Fred)"
* tag 'drm-fixes-2019-12-21' of git://anongit.freedesktop.org/drm/drm:
drm/exynos: gsc: add missed component_del
drm/i915: Fix pid leak with banned clients
drm/i915/gem: Keep request alive while attaching fences
drm/i915: Fix WARN_ON condition for cursor plane ddb allocation
drm/i915/gvt: Fix guest boot warning
drm/i915/tgl: Drop Wa#1178
drm/i915/ehl: Define EHL powerwells independently of ICL
drm/i915: Set fence_work.ops before dma_fence_init
drm/i915: Copy across scheduler behaviour flags across submit fences
drm/i915/dsb: Fix in mmio offset calculation of DSB instance
drm/i915/gvt: Pin vgpu dma address before using
drm/i915/gvt: set guest display buffer as readonly
drm/i915/gvt: use vgpu lock for active state setting
Linus Torvalds [Fri, 20 Dec 2019 21:30:49 +0000 (13:30 -0800)]
Merge tag 'io_uring-5.5-20191220' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Here's a set of fixes that should go into 5.5-rc3 for io_uring.
This is bigger than I'd like it to be, mainly because we're fixing the
case where an application reuses sqe data right after issue. This
really must work, or it's confusing. With 5.5 we're flagging us as
submit stable for the actual data, this must also be the case for
SQEs.
Honestly, I'd really like to add another series on top of this, since
it cleans it up considerable and prevents any SQE reuse by design. I
posted that here:
and may still send it your way early next week once it's been looked
at and had some more soak time (does pass all regression tests). With
that series, we've unified the prep+issue handling, and only the prep
phase even has access to the SQE.
Anyway, outside of that, fixes in here for a few other issues that
have been hit in testing or production"
* tag 'io_uring-5.5-20191220' of git://git.kernel.dk/linux-block:
io_uring: io_wq_submit_work() should not touch req->rw
io_uring: don't wait when under-submitting
io_uring: warn about unhandled opcode
io_uring: read opcode and user_data from SQE exactly once
io_uring: make IORING_OP_TIMEOUT_REMOVE deferrable
io_uring: make IORING_OP_CANCEL_ASYNC deferrable
io_uring: make IORING_POLL_ADD and IORING_POLL_REMOVE deferrable
io_uring: make HARDLINK imply LINK
io_uring: any deferred command must have stable sqe data
io_uring: remove 'sqe' parameter to the OP helpers that take it
io_uring: fix pre-prepped issue with force_nonblock == true
io-wq: re-add io_wq_current_is_worker()
io_uring: fix sporadic -EFAULT from IORING_OP_RECVMSG
io_uring: fix stale comment and a few typos
Dave Airlie [Fri, 20 Dec 2019 20:08:19 +0000 (06:08 +1000)]
Merge tag 'drm-intel-fixes-2019-12-19' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix to drop an unused and harmful display W/A
- Fix to define EHL power wells independent of ICL
- Fix for priority inversion on bonded requests
- Fix in mmio offset calculation of DSB instance
- Fix memory leak from get_task_pid when banning clients
- Fixes to avoid dereference of uninitialized ops in dma_fence tracing
and keep reference to execbuf object until submitted.
Helge Deller [Fri, 20 Dec 2019 20:00:19 +0000 (21:00 +0100)]
parisc: Fix compiler warnings in debug_core.c
Fix this compiler warning:
kernel/debug/debug_core.c: In function ‘kgdb_cpu_enter’:
arch/parisc/include/asm/cmpxchg.h:48:3: warning: value computed is not used [-Wunused-value]
48 | ((__typeof__(*(ptr)))__xchg((unsigned long)(x), (ptr), sizeof(*(ptr))))
arch/parisc/include/asm/atomic.h:78:30: note: in expansion of macro ‘xchg’
78 | #define atomic_xchg(v, new) (xchg(&((v)->counter), new))
| ^~~~
kernel/debug/debug_core.c:596:4: note: in expansion of macro ‘atomic_xchg’
596 | atomic_xchg(&kgdb_active, cpu);
| ^~~~~~~~~~~
If __blk_rq_map_user_iov() is failed in blk_rq_map_user_iov(),
the bio(s) which is allocated before this failing will leak. The
refcount of the bio(s) is init to 1 and increased to 2 by calling
bio_get(), but __blk_rq_unmap_user() only decrease it to 1, so
the bio cannot be freed. Fix it by calling blk_rq_unmap_user().
Reviewed-by: Bob Liu <bob.liu@oracle.com> Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
projects / kernel.git / log