The change in iavf_fdir_is_dup_fltr adds a spinlock around a loop which
iterates over all filters and looks for a duplicate. The filter can be
removed from list and freed from memory at the same time it's being
compared. All other places where filters are deleted are already
protected with spinlock.
The remaining changes protect adapter->fdir_active_fltr variable so now
all its uses are under a spinlock.
Fixes: 527691bf0682 ("iavf: Support IPv4 Flow Director filters") Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230807205011.3129224-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using the syzkaller repro with reduced packet size it was discovered
that XDP_PACKET_HEADROOM is not checked in tun_can_build_skb(),
although pad may be incremented in tun_build_skb(). This may end up
with exceeding the PAGE_SIZE limit in tun_build_skb().
Jason Wang <jasowang@redhat.com> proposed to count XDP_PACKET_HEADROOM
always (e.g. without rcu_access_pointer(tun->xdp_prog)) in
tun_can_build_skb() since there's a window during which XDP program
might be attached between tun_can_build_skb() and tun_build_skb().
BUG_ON(!vlan_info) is triggered in unregister_vlan_dev() with
following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add bond0 type bond mode 0
# ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
# ip netns exec ns1 ip link set bond_slave_1 master bond0
# ip netns exec ns1 ip link add link bond_slave_1 name vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link bond0 name bond0_vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set bond_slave_1 nomaster
# ip netns del ns1
The logical analysis of the problem is as follows:
1. create ETH_P_8021AD protocol vlan10 for bond_slave_1:
register_vlan_dev()
vlan_vid_add()
vlan_info_alloc()
__vlan_vid_add() // add [ETH_P_8021AD, 10] vid to bond_slave_1
2. create ETH_P_8021AD protocol bond0_vlan10 for bond0:
register_vlan_dev()
vlan_vid_add()
__vlan_vid_add()
vlan_add_rx_filter_info()
if (!vlan_hw_filter_capable(dev, proto)) // condition established because bond0 without NETIF_F_HW_VLAN_STAG_FILTER
return 0;
if (netif_device_present(dev))
return dev->netdev_ops->ndo_vlan_rx_add_vid(dev, proto, vid); // will be never called
// The slaves of bond0 will not refer to the [ETH_P_8021AD, 10] vid.
3. detach bond_slave_1 from bond0:
__bond_release_one()
vlan_vids_del_by_dev()
list_for_each_entry(vid_info, &vlan_info->vid_list, list)
vlan_vid_del(dev, vid_info->proto, vid_info->vid);
// bond_slave_1 [ETH_P_8021AD, 10] vid will be deleted.
// bond_slave_1->vlan_info will be assigned NULL.
4. delete vlan10 during delete ns1:
default_device_exit_batch()
dev->rtnl_link_ops->dellink() // unregister_vlan_dev() for vlan10
vlan_info = rtnl_dereference(real_dev->vlan_info); // real_dev of vlan10 is bond_slave_1
BUG_ON(!vlan_info); // bond_slave_1->vlan_info is NULL now, bug is triggered!!!
Add S-VLAN tag related features support to bond driver. So the bond driver
will always propagate the VLAN info to its slaves.
Fix a refcount underflow problem reported by syzbot that can happen
when a system is running out of memory. If xp_alloc_tx_descs() fails,
and it can only fail due to not having enough memory, then the error
path is triggered. In this error path, the refcount of the pool is
decremented as it has incremented before. However, the reference to
the pool in the socket was not nulled. This means that when the socket
is closed later, the socket teardown logic will think that there is a
pool attached to the socket and try to decrease the refcount again,
leading to a refcount underflow.
I chose this fix as it involved adding just a single line. Another
option would have been to move xp_get_pool() and the assignment of
xs->pool to after the if-statement and using xs_umem->pool instead of
xs->pool in the whole if-statement resulting in somewhat simpler code,
but this would have led to much more churn in the code base perhaps
making it harder to backport.
Fixes: ba3beec2ec1d ("xsk: Fix possible crash when multiple sockets are created") Reported-by: syzbot+8ada0057e69293a05fd4@syzkaller.appspotmail.com Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/r/20230809142843.13944-1-magnus.karlsson@gmail.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tuning of the effective buffer size through setsockopts was working for
SMC traffic only but not for TCP fall-back connections even before
commit 0227f058aa29 ("net/smc: Unbind r/w buffer size from clcsock and
make them tunable"). That change made it apparent that TCP fall-back
connections would use net.smc.[rw]mem as buffer size instead of
net.ipv4_tcp_[rw]mem.
Amend the code that copies attributes between the (TCP) clcsock and the
SMC socket and adjust buffer sizes appropriately:
- Copy over sk_userlocks so that both sockets agree on whether tuning
via setsockopt is active.
- When falling back to TCP use sk_sndbuf or sk_rcvbuf as specified with
setsockopt. Otherwise, use the sysctl value for TCP/IPv4.
- Likewise, use either values from setsockopt or from sysctl for SMC
(duplicated) on successful SMC connect.
In smc_tcp_listen_work() drop the explicit copy of buffer sizes as that
is taken care of by the attribute copy.
Fixes: 0227f058aa29 ("net/smc: Unbind r/w buffer size from clcsock and make them tunable") Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
value changed: 0x0000000000000000 -> 0x0000000020000081
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 6.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230803145600.2937518-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coccicheck reports the error below:
net/mptcp/protocol.c:3330:15-28: ERROR: test of a variable/field address
Since the address of msk->cb_flags is used in __test_and_clear_bit, the
address should not be NULL. The judgment for if (unlikely(msk->cb_flags))
will always be true, we should check the real value of msk->cb_flags here.
Fixes: 65a569b03ca8 ("mptcp: optimize release_cb for the common case") Signed-off-by: Xiang Yang <xiangyang3@huawei.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Link: https://lore.kernel.org/r/20230803072438.1847500-1-xiangyang3@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a kernel with CONFIG_MISDN_DSP=y and CONFIG_CFI_CLANG=y,
there is a failure when dsp_cmx_send() is called indirectly from
call_timer_fn():
The function pointer prototype that call_timer_fn() expects is
void (*fn)(struct timer_list *)
whereas dsp_cmx_send() has a parameter type of 'void *', which causes
the control flow integrity checks to fail because the parameter types do
not match.
Change dsp_cmx_send()'s parameter type to be 'struct timer_list' to
match the expected prototype. The argument is unused anyways, so this
has no functional change, aside from avoiding the CFI failure.
Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202308020936.58787e6c-oliver.sang@intel.com Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Fixes: e313ac12eb13 ("mISDN: Convert timers to use timer_setup()") Link: https://lore.kernel.org/r/20230802-fix-dsp_cmx_send-cfi-failure-v1-1-2f2e79b0178d@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strp_done is only called when psock->progs.stream_parser is not NULL,
but stream_parser was set to NULL by sk_psock_stop_strp(), called
by sk_psock_drop() earlier. So, strp_done can never be called.
Introduce SK_PSOCK_RX_ENABLED to mark whether there is strp on psock.
Change the condition for calling strp_done from judging whether
stream_parser is set to judging whether this flag is set. This flag is
only set once when strp_init() succeeds, and will never be cleared later.
Fixes: c0d95d3380ee ("bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/r/20230804073740.194770-3-xukuohai@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sock_map_del_link() operates on both SOCKMAP and SOCKHASH, although
both types have member named "progs", the offset of "progs" member in
these two types is different, so "progs" should be accessed with the
real map type.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/r/20230804073740.194770-2-xukuohai@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xdp->frame_sz > PAGE_SIZE check was introduced in commit c8741e2bfe87
("xdp: Allow bpf_xdp_adjust_tail() to grow packet size"). But Jesper
Dangaard Brouer <jbrouer@redhat.com> noted that after introducing the
xdp_init_buff() which all XDP driver use - it's safe to remove this
check. The original intend was to catch cases where XDP drivers have
not been updated to use xdp.frame_sz, but that is not longer a concern
(since xdp_init_buff).
Running the initial syzkaller repro it was discovered that the
contiguous physical memory allocation is used for both xdp paths in
tun_get_user(), e.g. tun_build_skb() and tun_alloc_skb(). It was also
stated by Jesper Dangaard Brouer <jbrouer@redhat.com> that XDP can
work on higher order pages, as long as this is contiguous physical
memory (e.g. a page).
The test checks that filters that match on source or destination MAC
were only hit once. A host can send more than one packet with a given
source or destination MAC, resulting in failures.
Fix by relaxing the success criterion and instead check that the filters
were not hit zero times. Using tc_check_at_least_x_packets() is also an
option, but it is not available in older kernels.
The default timeout for selftests is 45 seconds, but it is not enough
for forwarding selftests which can takes minutes to finish depending on
the number of tests cases:
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# TEST: IGMPv2 report 239.10.10.10 [ OK ]
# TEST: IGMPv2 leave 239.10.10.10 [ OK ]
# TEST: IGMPv3 report 239.10.10.10 is_include [ OK ]
# TEST: IGMPv3 report 239.10.10.10 include -> allow [ OK ]
#
not ok 1 selftests: net/forwarding: bridge_igmp.sh # TIMEOUT 45 seconds
Fix by switching off the timeout and setting it to 0. A similar change
was done for BPF selftests in commit 6fc5916cc256 ("selftests: bpf:
Switch off timeout").
Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/8d149f8c-818e-d141-a0ce-a6bae606bc22@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-3-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As explained in [1], the forwarding selftests are meant to be run with
either physical loopbacks or veth pairs. The interfaces are expected to
be specified in a user-provided forwarding.config file or as command
line arguments. By default, this file is not present and the tests fail:
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
[...]
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# Command line is not complete. Try option "help"
# Failed to create netif
not ok 1 selftests: net/forwarding: bridge_igmp.sh # exit=1
[...]
Fix by skipping a test if interfaces are not provided either via the
configuration file or command line arguments.
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
[...]
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# SKIP: Cannot create interface. Name not specified
ok 1 selftests: net/forwarding: bridge_igmp.sh # SKIP
[1] tools/testing/selftests/net/forwarding/README
Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/856d454e-f83c-20cf-e166-6dc06cbc1543@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Layer 3 hardware stats cannot be used when the underlying interfaces are
veth pairs, resulting in failures:
# ./hw_stats_l3_gre.sh
TEST: ping gre flat [ OK ]
TEST: Test rx packets: [FAIL]
Traffic not reflected in the counter: 0 -> 0
TEST: Test tx packets: [FAIL]
Traffic not reflected in the counter: 0 -> 0
Fix by skipping the test when used with veth pairs.
Fixes: 813f97a26860 ("selftests: forwarding: Add a tunnel-based test for L3 HW stats") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-10-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A handful of tests require physical loopbacks to be used instead of veth
pairs. Add a helper that these tests will invoke in order to be skipped
when executed with veth pairs.
Fixes: 64916b57c0b1 ("selftests: forwarding: Add speed and auto-negotiation test") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-7-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3bcbc20942db ("selftests/rseq: Play nice with binaries statically
linked against glibc 2.35+") which is now in Linus' tree introduced uses
of __weak but did nothing to ensure that a definition is provided for it
resulting in build failures for the rseq tests:
rseq.c:41:1: error: unknown type name '__weak'
__weak ptrdiff_t __rseq_offset;
^
rseq.c:41:17: error: expected ';' after top level declarator
__weak ptrdiff_t __rseq_offset;
^
;
rseq.c:42:1: error: unknown type name '__weak'
__weak unsigned int __rseq_size;
^
rseq.c:43:1: error: unknown type name '__weak'
__weak unsigned int __rseq_flags;
Fix this by using the definition from tools/include compiler.h.
Fixes: 3bcbc20942db ("selftests/rseq: Play nice with binaries statically linked against glibc 2.35+") Signed-off-by: Mark Brown <broonie@kernel.org>
Message-Id: <20230804-kselftest-rseq-build-v1-1-015830b66aa9@kernel.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BCMs aren't directly associated with the data path (i.e. ACV) and
therefore don't communicate using BW. Instead, they are simply
enabled/disabled with a simple bit mask. Add support for these.
Commit 813665564b3d ("iio: core: Convert to use firmware node handle
instead of OF node") switched the kind of nodes to use for label
retrieval in device registration. Probably an unwanted change in that
commit was that if the device has no parent then NULL pointer is
accessed. This is what happens in the stock IIO dummy driver when a
new entry is created in configfs:
Since there seems to be no reason to make a parent device of an IIO
dummy device mandatory, let’s prevent the invalid memory access in
__iio_device_register when the parent device is NULL. With this
change, the IIO dummy driver works fine with configfs.
Fixes: 813665564b3d ("iio: core: Convert to use firmware node handle instead of OF node") Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Milan Zamazal <mzamazal@redhat.com> Link: https://lore.kernel.org/r/20230719083208.88149-1-mzamazal@redhat.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original commit adding that check tried to protect the kenrel against
a potential invalid NULL pointer access.
However we call nouveau_connector_detect_depth once without a native_mode
set on purpose for non LVDS connectors and this broke DP support in a few
cases.
Cc: Olaf Skibbe <news@kravcenko.com> Cc: Lyude Paul <lyude@redhat.com> Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/238 Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/245 Fixes: 20a2ce87fbaf8 ("drm/nouveau/dp: check for NULL nv_connector->native_mode") Signed-off-by: Karol Herbst <kherbst@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230805101813.2603989-1-kherbst@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tao Liu reported a boot hang on an Intel Atom machine due to an unmapped
EFI config table. The reason being that the CC blob which contains the
CPUID page for AMD SNP guests is parsed for before even checking
whether the machine runs on AMD hardware.
Usually that's not a problem on !AMD hw - it simply won't find the CC
blob's GUID and return. However, if any parts of the config table
pointers array is not mapped, the kernel will #PF very early in the
decompressor stage without any opportunity to recover.
Therefore, do a superficial CPUID check before poking for the CC blob.
This will fix the current issue on real hardware. It would also work as
a guest on a non-lying hypervisor.
For the lying hypervisor, the check is done again, *after* parsing the
CC blob as the real CPUID page will be present then.
Clear the #VC handler in case SEV-{ES,SNP} hasn't been detected, as
a precaution.
Fixes: c01fce9cef84 ("x86/compressed: Add SEV-SNP feature detection/setup") Reported-by: Tao Liu <ltao@redhat.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Tao Liu <ltao@redhat.com> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/20230601072043.24439-1-ltao@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This might confuse users who are not aware of 5-level paging and expect
all userspace addresses to be under the 47-bit border.
So far problem has only been triggered with ASLR disabled, although it
may also occur with ASLR enabled if the layout is randomized in a just
right way.
The problem happens due to custom placement for the VMAs in the VDSO
code: vdso_addr() tries to place them above the stack and checks the
result against TASK_SIZE_MAX, which is wrong. TASK_SIZE_MAX is set to
the 56-bit border on 5-level paging machines. Use DEFAULT_MAP_WINDOW
instead.
Fixes: b569bab78d8d ("x86/mm: Prepare to expose larger address space to userspace") Reported-by: Yingcong Wu <yingcong.wu@intel.com> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20230803151609.22141-1-kirill.shutemov%40linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
provided a fix for the Zen2 VZEROUPPER data corruption bug affecting
a range of CPU models, but the AMD Custom APU 0405 found on SteamDeck
was not listed, although it is clearly affected by the vulnerability.
Add this CPU variant to the Zenbleed erratum list, in order to
unconditionally enable the fallback fix until a proper microcode update
is available.
The assertion added to verify the difference in bits set of the
addresses of srso_untrain_ret_alias() and srso_safe_ret_alias() would fail
to link in LLVM's ld.lld linker with the following error:
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:210: at least one side of
the expression must be absolute
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:211: at least one side of
the expression must be absolute
Use ABSOLUTE to evaluate the expression referring to at least one of the
symbols so that LLD can evaluate the linker script.
Also, add linker version info to the comment about XOR being unsupported
in either ld.bfd or ld.lld until somewhat recently.
When connecting to some DisplayPort partners, the initial status update
after entering DisplayPort Alt Mode notifies that the DFP_D/UFP_D is not in
the connected state. This leads to sending a configure message that keeps
the device in USB mode. The port partner then sets DFP_D/UFP_D to the
connected state and HPD to high in the same Attention message. Currently,
the HPD signal is dropped in order to handle configuration.
This patch saves changes to the HPD signal when the device chooses to
configure during dp_altmode_status_update, and invokes sysfs_notify if
necessary for HPD after configuring.
Do not transition to SNK_UNATTACHED state when receiving vsafe0v event
while in SNK_HARD_RESET_WAIT_VBUS. Ignore VBUS off events as well as
in some platforms VBUS off can be signalled more than once.
[143515.364753] Requesting mux state 1, usb-role 2, orientation 2
[143515.365520] pending state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_SINK_ON @ 650 ms [rev3 HARD_RESET]
[143515.632281] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_HARD_RESET_SINK_OFF, polarity 1, disconnected]
[143515.637214] VBUS on
[143515.664985] VBUS off
[143515.664992] state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_WAIT_VBUS [rev3 HARD_RESET]
[143515.665564] VBUS VSAFE0V
[143515.665566] state change SNK_HARD_RESET_WAIT_VBUS -> SNK_UNATTACHED [rev3 HARD_RESET]
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() because last_role is same
as current role. This happens since last_role gets initialised
to zero during the probe.
To avoid this, add a new flag initial_detection into struct
usb_conn_info, which prevents bailing out during initial
detection.
Cc: <stable@vger.kernel.org> # 5.4 Fixes: 4602f3bff266 ("usb: common: add USB GPIO based connection detection driver") Signed-off-by: Prashanth K <quic_prashk@quicinc.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/1690880632-12588-1-git-send-email-quic_prashk@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avichal Rakesh reported a kernel panic that occurred when the UVC
gadget driver was removed from a gadget's configuration. The panic
involves a somewhat complicated interaction between the kernel driver
and a userspace component (as described in the Link tag below), but
the analysis did make one thing clear: The Gadget core should
accomodate gadget drivers calling usb_gadget_deactivate() as part of
their unbind procedure.
Currently this doesn't work. gadget_unbind_driver() calls
driver->unbind() while holding the udc->connect_lock mutex, and
usb_gadget_deactivate() attempts to acquire that mutex, which will
result in a deadlock.
The simple fix is for gadget_unbind_driver() to release the mutex when
invoking the ->unbind() callback. There is no particular reason for
it to be holding the mutex at that time, and the mutex isn't held
while the ->bind() callback is invoked. So we'll drop the mutex
before performing the unbind callback and reacquire it afterward.
We'll also add a couple of comments to usb_gadget_activate() and
usb_gadget_deactivate(). Because they run in process context they
must not be called from a gadget driver's ->disconnect() callback,
which (according to the kerneldoc for struct usb_gadget_driver in
include/linux/usb/gadget.h) may run in interrupt context. This may
help prevent similar bugs from arising in the future.
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead.
ASPM Mode is ASPM_MODE_CFG need to judge the value of clkreq_0
to set HIGH or LOW, if the ASPM Mode is ASPM_MODE_REG
always set to HIGH during the initialization.
In binder_init(), the destruction of binder_alloc_shrinker_init() is not
performed in the wrong path, which will cause memory leaks. So this commit
introduces binder_alloc_shrinker_exit() and calls it in the wrong path to
fix that.
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com> Acked-by: Carlos Llamas <cmllamas@google.com> Fixes: f2517eb76f1f ("android: binder: Add global lru shrinker to binder") Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20230625154937.64316-1-qi.zheng@linux.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The affected lines were resulting in a NULL pointer dereference on our
platform because the device tree contained the following list of
compatible strings:
Since the driver doesn't declare a compatible string "ti,ina232", the OF
matching succeeds on "ti,ina231". But the I2C device ID info is
populated via the first compatible string, cf. modalias population in
of_i2c_get_board_info(). Since there is no "ina232" entry in the legacy
I2C device ID table either, the struct i2c_device_id *id pointer in the
probe function is NULL.
Fix this by using the already populated type variable instead, which
points to the proper driver data. Since the name is also wanted, add a
generic one to the ina2xx_config table.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors") Link: https://lore.kernel.org/r/20230619141239.2257392-1-alvin@pqrs.dk Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AC excitation enable feature exposed to user on AD7192, allowing a bit
which should be 0 to be set. This feature is specific only to AD7195. AC
excitation attribute moved accordingly.
In the AD7195 documentation, the AC excitation enable bit is on position
22 in the Configuration register. ACX macro changed to match correct
register and bit.
Note that the fix tag is for the commit that moved the driver out of
staging.
Fixes: b581f748cce0 ("staging: iio: adc: ad7192: move out of staging") Signed-off-by: Alisa Roman <alisa.roman@analog.com> Cc: stable@vger.kernel.org Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20230614155242.160296-1-alisa.roman@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The regulator_get_voltage() function returns negative error codes.
This function saves it to an unsigned int and then does some range
checking and, since the error code falls outside the correct range,
it returns -EINVAL.
Beyond the messiness, this is bad because the regulator_get_voltage()
function can return -EPROBE_DEFER and it's important to propagate that
back properly so it can be handled.
Fixes: da35a7b526d9 ("iio: frequency: admv1013: add support for ADMV1013") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/ce75aac3-2aba-4435-8419-02e59fdd862b@moroto.mountain Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct cros_ec_command contains several integer fields and a
trailing array. An allocation size neglecting the integer fields can
lead to buffer overrun.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org> Signed-off-by: Yiyuan Guo <yguoaz@gmail.com> Fixes: 974e6f02e27e ("iio: cros_ec_sensors_core: Add common functions for the ChromeOS EC Sensor Hub.") Link: https://lore.kernel.org/r/20230630143719.1513906-1-yguoaz@gmail.com Cc: <Stable@vger.kerenl.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
O_TMPFILE is actually __O_TMPFILE|O_DIRECTORY. This means that the old
check for whether RESOLVE_CACHED can be used would incorrectly think
that O_DIRECTORY could not be used with RESOLVE_CACHED.
[Why&How]
If the timing generator isnt running, it does not make sense to trigger
a sync on the corresponding OTG. Check this condition before starting.
Otherwise, this will cause error like:
*ERROR* GSL: Timeout on reset trigger!
Fixes: dc55b106ad47 ("drm/amd/display: Disable phantom OTG after enable for plane disable") Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ NOTE: This is also 5f9f97c02dd2 ("drm/amd/display: trigger timing sync
only if TG is running") ] Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: dc55b106ad47 ("drm/amd/display: Disable phantom OTG after enable for plane disable") CC: Alvin Lee <Alvin.Lee2@amd.com> CC: Alan Liu <HaoPing.Liu@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Description]
- If we fail validation, we should retain the phantom
stream/planes
- Full updates assume that phantom pipes will be fully
removed, but if validation fails we keep the phantom
pipes
- Therefore we have to retain the plane/stream if validation
fails (since the refcount is decremented before validation,
and the expectation is that it's fully freed when the old
dc_state is released)
Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Brian Chang <Brian.Chang@amd.com> Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Description]
- Need to disable phantom OTG after it's enabled
in order to restore it to it's original state.
- If it's enabled and then an MCLK switch comes in
we may not prefetch the correct data since the phantom
OTG could already be in the middle of the frame.
Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sub-viewport (Subvp) feature is used for changing MCLK without causing
any display artifact, requiring special treatment from the plane and
stream perspective since DC needs to read data from the cache when using
subvp. However, the function dc_commit_updates_for_stream does not
provide all the support needed by this feature which will make this
function legacy at some point. For this reason, this commit enables
dc_update_planes_and_stream for ASICs that support this feature but
preserves the old behavior for other ASICs. However,
dc_update_planes_and_stream should replace dc_commit_updates_for_stream
for all ASICs since it does most of the tasks executed by
dc_commit_updates_for_stream with other extra operations, but we need to
run tests before making this change.
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ODM to combine on the eDP panel with ABM causes the color difference to
the panel since the ABM module only sets one pipe. Hence, this commit
blocks ABM in case of ODM combined on eDP.
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OTG instance is not updated in dc_commit_state_no_check for newly
committed streams because mode_change is not set. Notice that OTG update
is part of the software state, and after hardware programming, it must
be updated; for this reason, this commit updates the OTG offset right
after hardware programming.
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A seamless boot stream has hardware resources assigned to it, and adding
a new stream means rebuilding the current assignment. It is desirable to
avoid this situation since it may cause light-up issues on the VGA
monitor on USB-C. This commit swaps the seamless boot stream to pipe 0
(if necessary) to ensure that the pipe context matches.
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DC stream can be seen as a representation of the DCN backend or the data
struct that represents the center of the display pipeline. The front end
(i.e., planes) is connected to the DC stream, and in its turn, streams
are connected to the DC link. Due to this dynamic, DC must handle the
following scenarios:
1. A stream is removed;
2. A new stream is created;
3. An unchanged stream had some updates on its planes.
These combinations require that the new stream data struct become
updated and has a valid global state. For handling multiple corner cases
associated with stream operations, this commit introduces a function
dedicated to manipulating stream changes and invokes the state
validation function after that.
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Co-developed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An intentional delay is added on soft ctf triggered. Then there will
be a double check for the GPU temperature before taking further
action. This can avoid unintended shutdown due to temperature
momentary fluctuation.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[ Hand-modified because:
* XCP support added to amdgpu.h in kernel 6.5
and is not necessary for this fix.
* SMU microcode initialization moved in 32806038aa76 ("drm/amd: Load SMU microcode during early_init") ] Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1267 Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2779 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable peak profiling mode shader/memory clock reporting for powerplay
framework.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable peak profiling mode shader/memory clocks reporting for swsmu
framework.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During unmount process of nilfs2, nothing holds nilfs_root structure after
nilfs2 detaches its writer in nilfs_detach_log_writer(). Previously,
nilfs_evict_inode() could cause use-after-free read for nilfs_root if
inodes are left in "garbage_list" and released by nilfs_dispose_list at
the end of nilfs_detach_log_writer(), and this bug was fixed by commit 9b5a04ac3ad9 ("nilfs2: fix use-after-free bug of nilfs_root in
nilfs_evict_inode()").
However, it turned out that there is another possibility of UAF in the
call path where mark_inode_dirty_sync() is called from iput():
This can happen after commit 0ae45f63d4ef ("vfs: add support for a
lazytime mount option"), which changed iput() to call
mark_inode_dirty_sync() on its final reference if i_state has I_DIRTY_TIME
flag and i_nlink is non-zero.
This issue appears after commit 28a65b49eb53 ("nilfs2: do not write dirty
data after degenerating to read-only") when using the syzbot reproducer,
but the issue has potentially existed before.
Fix this issue by adding a "purging flag" to the nilfs structure, setting
that flag while disposing the "garbage_list" and checking it in
__nilfs_mark_inode_dirty().
Unlike commit 9b5a04ac3ad9 ("nilfs2: fix use-after-free bug of nilfs_root
in nilfs_evict_inode()"), this patch does not rely on ns_writer to
determine whether to skip operations, so as not to break recovery on
mount. The nilfs_salvage_orphan_logs routine dirties the buffer of
salvaged data before attaching the log writer, so changing
__nilfs_mark_inode_dirty() to skip the operation when ns_writer is NULL
will cause recovery write to fail. The purpose of using the cleanup-only
flag is to allow for narrowing of such conditions.
Link: https://lkml.kernel.org/r/20230728191318.33047-1-konishi.ryusuke@gmail.com Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+74db8b3087f293d3a13a@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/000000000000b4e906060113fd63@google.com Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> # 4.0+ Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the pthread allocation for each array item is based on the size
of a pthread_t pointer and should be the size of the pthread_t structure,
so the allocation is under-allocating the correct size. Fix this by using
the size of each element in the pthreads array.
Static analysis cppcheck reported:
tools/testing/radix-tree/regression1.c:180:2: warning: Size of pointer
'threads' used instead of size of its data. [pointerSize]
Link: https://lkml.kernel.org/r/20230727160930.632674-1-colin.i.king@gmail.com Fixes: 1366c37ed84b ("radix tree test harness") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users report a white flickering screen on multiple systems that
is tied to having 64GB or more memory. When S/G is enabled pages
will get pinned to both VRAM carve out and system RAM leading to
this.
Until it can be fixed properly, disable S/G when 64GB of memory or
more is detected. This will force pages to be pinned into VRAM.
This should fix white screen flickers but if VRAM pressure is
encountered may lead to black screens. It's a trade-off for now.
Fixes: 81d0bcf99009 ("drm/amdgpu: make display pinning more flexible (v2)") Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com> Cc: Roman Li <roman.li@amd.com> Cc: <stable@vger.kernel.org> # 6.1.y: bf0207e172703 ("drm/amdgpu: add S/G display parameter") Cc: <stable@vger.kernel.org> # 6.4.y Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2735 Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2354 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some users have reported flickerng with S/G display. We've
tried extensively to reproduce and debug the issue on a wide
variety of platform configurations (DRAM bandwidth, etc.) and
a variety of monitors, but so far have not been able to. We
disabled S/G display on a number of platforms to address this
but that leads to failure to pin framebuffers errors and
blank displays when there is memory pressure or no displays
at all on systems with limited carveout (e.g., Chromebooks).
Add a option to disable this as a debugging option as a
way for users to disable this, depending on their use case,
and for us to help debug this further.
v2: fix typo
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't set predefined degamma curve to cursor plane if the cursor
attribute flag is not set. Applying a degamma curve to the cursor by
default breaks userspace expectation. Checking the flag before
performing any color transformation prevents too dark cursor gamma in
DCN3+ on many Linux desktop environment (KDE Plasma, GNOME,
wlroots-based, etc.) as reported at:
- https://gitlab.freedesktop.org/drm/amd/-/issues/1513
This is the same approach followed by DCN2 drivers where the issue is
not present.
Fixes: 03f54d7d3448 ("drm/amd/display: Add DCN3 DPP") Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1513 Signed-off-by: Melissa Wen <mwen@igalia.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Tested-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma-buf backend is supposed to provide its own vm_ops, but some
implementation just have nothing special to do and leave vm_ops
untouched, probably expecting this field to be zero initialized (this
is the case with the system_heap implementation for instance).
Let's reset vma->vm_ops to NULL to keep things working with these
implementations.
Fixes: 26d3ac3cb04d ("drm/shmem-helpers: Redirect mmap for imported dma-buf") Cc: <stable@vger.kernel.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reported-by: Roman Stratiienko <r.stratiienko@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Tested-by: Roman Stratiienko <r.stratiienko@gmail.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20230724112610.60974-1-boris.brezillon@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we use the drm_dp_dpcd_read_caps() helper in the DRM side of
nouveau in order to read the DPCD of a DP connector, which makes sure we do
the right thing and also check for extended DPCD caps. However, it turns
out we're not currently doing this on the nvkm side since we don't have
access to the drm_dp_aux structure there - which means that the DRM side of
the driver and the NVKM side can end up with different DPCD capabilities
for the same connector.
Ideally in order to fix this, we just want to use the
drm_dp_read_dpcd_caps() helper in nouveau. That's not currently possible
though, and is going to depend on having a bunch of the DP code moved out
of nvkm and into the DRM side of things as part of the GSP enablement work.
Until then however, let's workaround this problem by porting a copy of
drm_dp_read_dpcd_caps() into NVKM - which should fix this issue.
We have a lurking bug where Fragment Shader Helper Invocations can't load
from memory. But this is actually required in OpenGL and is causing random
hangs or failures in random shaders.
It is unknown how widespread this issue is, but shaders hitting this can
end up with infinite loops.
We enable those only on all Kepler and newer GPUs where we use our own
Firmware.
Nvidia's firmware provides a way to set a kernelspace controlled list of
mmio registers in the gr space from push buffers via MME macros.
v2: drop code for gm200 and newer.
Cc: Ben Skeggs <bskeggs@redhat.com> Cc: David Airlie <airlied@gmail.com> Cc: nouveau@lists.freedesktop.org Cc: stable@vger.kernel.org # 4.19+ Signed-off-by: Karol Herbst <kherbst@redhat.com> Reviewed-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230622152017.2512101-1-kherbst@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Samsung PM9B1 512G SSD found in some Lenovo Yoga 7 14ARB7 laptop units
reports eui as 0001000200030004 when resuming from s2idle, causing the
device to be removed with this error in dmesg:
nvme nvme0: identifiers changed for nsid 1
To fix this, add a quirk to ignore namespace identifiers for this device.
Signed-off-by: August Wikerfors <git@augustwikerfors.se> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Section 2.1 of the Platform Specification [1] states:
Unless otherwise specified by a given I/O device, I/O devices are on
ordering channel 0 (i.e., they are point-to-point strongly ordered).
which is not sufficient to guarantee that a readX() by a hart completes
before a subsequent delay() on the same hart (cf. memory-barriers.txt,
"Kernel I/O barrier effects").
Set the I(nput) bit in __io_ar() to restore the ordering, align inline
comments.
When initrd is loaded low, the secondary kernel fails like this:
INITRD: 0xdc581000+0x00eef000 overlaps in-use memory region
This initrd load address corresponds to the _end symbol, but the
reservation is aligned on PMD_SIZE, as explained by a comment in
setup_bootmem().
It is technically possible to align the initrd load address accordingly,
leaving a hole between the end of kernel and the initrd, but it is much
simpler to allocate the initrd top-down.
When unloading the MANA driver, mana_dealloc_queues() waits for the MANA
hardware to complete any inflight packets and set the pending send count
to zero. But if the hardware has failed, mana_dealloc_queues()
could wait forever.
Fix this by adding a timeout to the wait. Set the timeout to 120 seconds,
which is a somewhat arbitrary value that is more than long enough for
functional hardware to complete any sends.
Cc: stable@vger.kernel.org Fixes: ca9c54d2d6a5 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)") Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com> Link: https://lore.kernel.org/r/1691576525-24271-1-git-send-email-schakrabarti@linux.microsoft.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl330_pause() does not set anything to indicate paused condition which
causes pl330_tx_status() to return DMA_IN_PROGRESS. This breaks 8250
DMA flush after the fix in commit 57e9af7831dc ("serial: 8250_dma: Fix
DMA Rx rearm race"). The function comment for pl330_pause() claims
pause is supported but resume is not which is enough for 8250 DMA flush
to work as long as DMA status reports DMA_PAUSED when appropriate.
Add PAUSED state for descriptor and mark BUSY descriptors with PAUSED
in pl330_pause(). Return DMA_PAUSED from pl330_tx_status() when the
descriptor is PAUSED.
Despite commit 0ad529d9fd2b ("mptcp: fix possible divide by zero in
recvmsg()"), the mptcp protocol is still prone to a race between
disconnect() (or shutdown) and accept.
The root cause is that the mentioned commit checks the msk-level
flag, but mptcp_stream_accept() does acquire the msk-level lock,
as it can rely directly on the first subflow lock.
As reported by Christoph than can lead to a race where an msk
socket is accepted after that mptcp_subflow_queue_clean() releases
the listener socket lock and just before it takes destructive
actions leading to the following splat:
Address the issue by temporary removing the pending request socket
from the accept queue, so that racing accept() can't touch them.
After depleting the msk - the ssk still exists, as plain TCP sockets,
re-insert them into the accept queue, so that later inet_csk_listen_stop()
will complete the tcp socket disposal.
Fixes: 2a6a870e44dd ("mptcp: stops worker on unaccepted sockets at listener close") Cc: stable@vger.kernel.org Reported-by: Christoph Paasch <cpaasch@apple.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/423 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Link: https://lore.kernel.org/r/20230803-upstream-net-20230803-misc-fixes-6-5-v1-4-6671b1ab11cc@tessares.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the blamed commit, the MPTCP protocol unconditionally sends
TCP resets on all the subflows on disconnect().
That fits full-blown MPTCP sockets - to implement the fastclose
mechanism - but causes unexpected corruption of the data stream,
caught as sporadic self-tests failures.
Fixes: d21f83485518 ("mptcp: use fastclose on more edge scenarios") Cc: stable@vger.kernel.org Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/419 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Link: https://lore.kernel.org/r/20230803-upstream-net-20230803-misc-fixes-6-5-v1-3-6671b1ab11cc@tessares.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mptcp_join 'implicit EP' test currently fails when using ip mptcp:
$ ./mptcp_join.sh -iI
<snip>
001 implicit EP creation[fail] expected '10.0.2.2 10.0.2.2 id 1 implicit' found '10.0.2.2 id 1 rawflags 10 '
Error: too many addresses or duplicate one: -22.
ID change is prevented[fail] expected '10.0.2.2 10.0.2.2 id 1 implicit' found '10.0.2.2 id 1 rawflags 10 '
modif is allowed[fail] expected '10.0.2.2 10.0.2.2 id 1 signal' found '10.0.2.2 id 1 signal '
This happens because of two reasons:
- iproute v6.3.0 does not support the implicit flag, fixed with
iproute2-next commit 3a2535a41854 ("mptcp: add support for implicit
flag")
- pm_nl_check_endpoint wrongly expects the ip address to be repeated two
times in iproute output, and does not account for a final whitespace
in it.
This fixes the issue trimming the whitespace in the output string and
removing the double address in the expected string.
mptcp_join 'delete and re-add' test fails when using ip mptcp:
$ ./mptcp_join.sh -iI
<snip>
002 delete and re-add before delete[ ok ]
mptcp_info subflows=1 [ ok ]
Error: argument "ADDRESS" is wrong: invalid for non-zero id address
after delete[fail] got 2:2 subflows expected 1
This happens because endpoint delete includes an ip address while id is
not 0, contrary to what is indicated in the ip mptcp man page:
"When used with the delete id operation, an IFADDR is only included when
the ID is 0."
This fixes the issue using the $addr variable in pm_nl_del_endpoint()
only when id is 0.
The upcoming (and nearly finalized):
https://datatracker.ietf.org/doc/draft-collink-6man-pio-pflag/
will update the IPv6 RA to include a new flag in the PIO field,
which will serve as a hint to perform DHCPv6-PD.
As we don't want DHCPv6 related logic inside the kernel, this piece of
information needs to be exposed to userspace. The simplest option is to
simply expose the entire PIO through the already existing mechanism.
Even without this new flag, the already existing PIO R (router address)
flag (from RFC6275) cannot AFAICT be handled entirely in kernel,
and provides useful information that should be exposed to userspace
(the router's global address, for use by Mobile IPv6).
Also cc'ing stable@ for inclusion in LTS, as while technically this is
not quite a bugfix, and instead more of a feature, it is absolutely
trivial and the alternative is manually cherrypicking into all Android
Common Kernel trees - and I know Greg will ask for it to be sent in via
LTS instead...
Cc: Jen Linkova <furry@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: David Ahern <dsahern@gmail.com> Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org> Cc: stable@vger.kernel.org Signed-off-by: Maciej Żenczykowski <maze@google.com> Link: https://lore.kernel.org/r/20230807102533.1147559-1-maze@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conversion from big-endian to native is done in a common function
mmc_app_send_scr(). Converting in moxart_transfer_pio() is extra.
Double conversion on a LE system returns an incorrect SCR value,
leads to errors:
mmc0: unrecognised SCR structure version 8
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver") Signed-off-by: Sergei Antonov <saproj@gmail.com> Cc: Jonas Jensen <jonas.jensen@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230627120549.2400325-1-saproj@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the allowedips self-test, nodes are inserted into the tree, but it
generated an even amount of nodes, but for checking maximum node depth,
there is of course the root node, which makes the total number
necessarily odd. With two few nodes added, it never triggered the
maximum depth check like it should have. So, add 129 nodes instead of
128 nodes, and do so with a more straightforward scheme, starting with
all the bits set, and shifting over one each time. Then increase the
maximum depth to 129, and choose a better name for that variable to
make it clear that it represents depth as opposed to bits.
Cc: stable@vger.kernel.org Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Link: https://lore.kernel.org/r/20230807132146.2191597-2-Jason@zx2c4.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test uses the 'TROUTE6' environment variable to encode the name of
the IPv6 traceroute utility. By default (without a configuration file),
this variable is not set, resulting in failures:
# ./ip6_forward_instats_vrf.sh
TEST: ping6 [ OK ]
TEST: Ip6InTooBigErrors [ OK ]
TEST: Ip6InHdrErrors [FAIL]
TEST: Ip6InAddrErrors [ OK ]
TEST: Ip6InDiscards [ OK ]
Fix by setting a default utility name and skip the test if the utility
is not present.
Fixes: 0857d6f8c759 ("ipv6: When forwarding count rx stats on the orig netdev") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-6-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RX full flags are raised if certain types of RX FIFO are full, and then
drop all following MPDU of AMPDU. In order to resume to receive MPDU
when RX FIFO becomes available, we clear the register bits by the
commit a0d99ebb3ecd ("wifi: rtw89: initialize DMA of CMAC"). But, 8852AE
needs more settings to support this. To quickly fix disconnection problem,
revert the behavior as before.
Fixes: a0d99ebb3ecd ("wifi: rtw89: initialize DMA of CMAC") Reported-by: Damian B <bronecki.damian@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217710 Cc: <Stable@vger.kernel.org> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Tested-by: Damian B <bronecki.damian@gmail.com> Link: https://lore.kernel.org/r/20230808005426.5327-1-pkshih@realtek.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nl80211_parse_mbssid_elems() uses a u8 variable num_elems to count the
number of MBSSID elements in the nested netlink attribute attrs, which can
lead to an integer overflow if a user of the nl80211 interface specifies
256 or more elements in the corresponding attribute in userspace. The
integer overflow can lead to a heap buffer overflow as num_elems determines
the size of the trailing array in elems, and this array is thereafter
written to for each element in attrs.
Note that this vulnerability only affects devices with the
wiphy->mbssid_max_interfaces member set for the wireless physical device
struct in the device driver, and can only be triggered by a process with
CAP_NET_ADMIN capabilities.
Fix this by checking for a maximum of 255 elements in attrs.
Cc: stable@vger.kernel.org Fixes: dc1e3cb8da8b ("nl80211: MBSSID and EMA support in AP mode") Signed-off-by: Keith Yeo <keithyjy@gmail.com> Link: https://lore.kernel.org/r/20230731034719.77206-1-keithyjy@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A KVM guest using SEV-ES or SEV-SNP with multiple vCPUs can trigger
a double fetch race condition vulnerability and invoke the VMGEXIT
handler recursively.
sev_handle_vmgexit() maps the GHCB page using kvm_vcpu_map() and then
fetches the exit code using ghcb_get_sw_exit_code(). Soon after,
sev_es_validate_vmgexit() fetches the exit code again. Since the GHCB
page is shared with the guest, the guest is able to quickly swap the
values with another vCPU and hence bypass the validation. One vmexit code
that can be rejected by sev_es_validate_vmgexit() is SVM_EXIT_VMGEXIT;
if sev_handle_vmgexit() observes it in the second fetch, the call
to svm_invoke_exit_handler() will invoke sev_handle_vmgexit() again
recursively.
To avoid the race, always fetch the GHCB data from the places where
sev_es_sync_from_ghcb stores it.
Exploiting recursions on linux kernel has been proven feasible
in the past, but the impact is mitigated by stack guard pages
(CONFIG_VMAP_STACK). Still, if an attacker manages to call the handler
multiple times, they can theoretically trigger a stack overflow and
cause a denial-of-service, or potentially guest-to-host escape in kernel
configurations without stack guard pages.
Note that winning the race reliably in every iteration is very tricky
due to the very tight window of the fetches; depending on the compiler
settings, they are often consecutive because of optimization and inlining.
Tested by booting an SEV-ES RHEL9 guest.
Fixes: CVE-2023-4155 Fixes: 291bd20d5d88 ("KVM: SVM: Add initial support for a VMGEXIT VMEXIT") Cc: stable@vger.kernel.org Reported-by: Andy Nguyen <theflow@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Validation of the GHCB is susceptible to time-of-check/time-of-use vulnerabilities.
To avoid them, we would like to always snapshot the fields that are read in
sev_es_validate_vmgexit(), and not use the GHCB anymore after it returns.
This means:
- invoking sev_es_sync_from_ghcb() before any GHCB access, including before
sev_es_validate_vmgexit()
- snapshotting all fields including the valid bitmap and the sw_scratch field,
which are currently not caching anywhere.
The valid bitmap is the first thing to be copied out of the GHCB; then,
further accesses will use the copy in svm->sev_es.
Fixes: 291bd20d5d88 ("KVM: SVM: Add initial support for a VMGEXIT VMEXIT") Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple smb2_ea_info buffers in FILE_FULL_EA_INFORMATION request
from client. ksmbd find next smb2_ea_info using ->NextEntryOffset of
current smb2_ea_info. ksmbd need to validate buffer length Before
accessing the next ea. ksmbd should check buffer length using buf_len,
not next variable. next is the start offset of current ea that got from
previous ea.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21598 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 2b9b8f3b68ed ("ksmbd: validate command payload size"), except
for SMB2_OPLOCK_BREAK_HE command, the request size of other commands
is not checked, it's not expected. Fix it by add check for request
size of other commands.
Cc: stable@vger.kernel.org Fixes: 2b9b8f3b68ed ("ksmbd: validate command payload size") Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Long Li <leo.lilong@huawei.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPM RNG functionality is not necessary for entropy when the CPU
already supports the RDRAND instruction. The TPM RNG functionality
was previously disabled on a subset of AMD fTPM series, but reports
continue to show problems on some systems causing stutter root caused
to TPM RNG functionality.
Expand disabling TPM RNG use for all AMD fTPMs whether they have versions
that claim to have fixed or not. To accomplish this, move the detection
into part of the TPM CRB registration and add a flag indicating that
the TPM should opt-out of registration to hwrng.
Cc: stable@vger.kernel.org # 6.1.y+ Fixes: b006c439d58d ("hwrng: core - start hwrng kthread also for untrusted sources") Fixes: f1324bbc4011 ("tpm: disable hwrng for fTPM on some AMD designs") Reported-by: daniil.stas@posteo.net Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217719 Reported-by: bitlord0xff@gmail.com Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217212 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Gunter reports:
Building loongarch:defconfig ... failed
--------------
Error log:
<stdin>:569:2: warning: #warning syscall fstat not implemented [-Wcpp]
arch/loongarch/kernel/setup.c: In function 'arch_cpu_finalize_init':
arch/loongarch/kernel/setup.c:86:9: error: implicit declaration of function 'alternative_instructions'
Actually introduced in v6.1.44 with commit 08e86d42e2c9 ("loongarch/cpu:
Switch to arch_cpu_finalize_init()"). Alternative instruction support
was only introduced for loongarch in v6.2 with commit 19e5eb15b00c
("LoongArch: Add alternative runtime patching mechanism").
Under certain circumstances, an integer division by 0 which faults, can
leave stale quotient data from a previous division operation on Zen1
microarchitectures.
Do a dummy division 0/1 before returning from the #DE exception handler
in order to avoid any leaks of potentially sensitive data.
projects / kernel.git / log