Soenke Huster [Fri, 14 Jan 2022 16:44:02 +0000 (17:44 +0100)]
Bluetooth: fix null ptr deref on hci_sync_conn_complete_evt
This event is just specified for SCO and eSCO link types.
On the reception of a HCI_Synchronous_Connection_Complete for a BDADDR
of an existing LE connection, LE link type and a status that triggers the
second case of the packet processing a NULL pointer dereference happens,
as conn->link is NULL.
Signed-off-by: Soenke Huster <soenke.huster@eknoes.de> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Dan Carpenter [Tue, 11 Jan 2022 07:23:19 +0000 (10:23 +0300)]
Bluetooth: hci_sync: unlock on error in hci_inquiry_result_with_rssi_evt()
Add unlocks to two error paths in hci_inquiry_result_with_rssi_evt().
Fixes: c11032d73493 ("Bluetooth: hci_event: Use skb_pull_data when processing inquiry results") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Mark Chen [Sun, 9 Jan 2022 19:23:59 +0000 (03:23 +0800)]
Bluetooth: mt7921s: Enable SCO over I2S
The driver has to issue the specific command to enable Bluetooth SCO over
the I2S/PCM interface on mt7921s, that is supported since the firmware
with version 20211222191101 was added, and the patch would not cause any
harm even when the old firmware is applied.
The SCO profile with the patch was tested by setting up a VOIP application,
connected to HFP device, checked telephony function can work normally.
Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Mark Chen [Sun, 9 Jan 2022 19:23:58 +0000 (03:23 +0800)]
Bluetooth: mt7921s: Support wake on bluetooth
Enable wake on bluetooth on mt7921s that can be supported since the
firmware with version 20211129211059 was added, and the patch would
not cause any harm even when the old firmware is applied.
The patch was tested by setting up an HID or HOGP profile to connect a
Bluetooth keyboard and mouse, then putting the system to suspend, then
trying to wake up the system by moving the Bluetooth keyboard or mouse,
and then checking if the system can wake up and be brought back to
the normal state.
Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'highdma' is known to be true.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be
1.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly.
Finally, inline bnx2x_set_coherency_mask() because it is now only a wrapper
for a single dma_set_mask_and_coherent() call.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
Moreover, dma_set_mask_and_coherent() returns 0 or -EIO, so the return
code of the function can be used directly. There is no need to 'rc = -EIO'
explicitly.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So if dma_set_mask_and_coherent() succeeds, 'netdev->features' will have
NETIF_F_HIGHDMA in all cases. Move the assignment of this feature in
be_netdev_init() instead be_probe() which is a much logical place.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So if dma_set_mask_and_coherent() succeeds, 'dma64' is know to be 'true'.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So, if dma_set_mask_and_coherent() succeeds, 'using_dac' is known to be
'true'. This variable can be removed.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
If dma_set_mask_and_coherent() succeeds, 'ap->pci_using_dac' is known to be
1. So 'pci_using_dac' can be removed from the 'struct ace_private'.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
If dma_set_mask_and_coherent() succeeds, 'dac_enabled' is known to be 1.
Simplify code and remove some dead code accordingly.
As stated in [1], dma_set_mask() with a 64-bit mask will never fail if
dev->dma_mask is non-NULL.
So, if it fails, the 32 bits case will also fail for the same reason.
So qlcnic_set_dma_mask(), (in qlcnic_main.c) can be simplified a lot and
inlined directly in its only caller.
If dma_set_mask_and_coherent() succeeds, 'pci_using_dac' is known to be 1.
So it can be removed from all the calling chain.
qlcnic_setup_netdev() can finally be simplified as-well.
Yunsheng Lin [Fri, 7 Jan 2022 09:00:42 +0000 (17:00 +0800)]
page_pool: remove spinlock in page_pool_refill_alloc_cache()
As page_pool_refill_alloc_cache() is only called by
__page_pool_get_cached(), which assumes non-concurrent access
as suggested by the comment in __page_pool_get_cached(), and
ptr_ring allows concurrent access between consumer and producer,
so remove the spinlock in page_pool_refill_alloc_cache().
Taehee Yoo [Sun, 9 Jan 2022 16:37:02 +0000 (16:37 +0000)]
amt: fix wrong return type of amt_send_membership_update()
amt_send_membership_update() would return -1 but it's return type is bool.
So, it should be used TRUE instead of -1.
Fixes: 19284cc854b3 ("amt: add data plane of amt interface") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Taehee Yoo <ap420073@gmail.com> Link: https://lore.kernel.org/r/20220109163702.6331-1-ap420073@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavel Skripkin [Thu, 6 Jan 2022 22:57:16 +0000 (01:57 +0300)]
net: mcs7830: handle usb read errors properly
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com Fixes: 3d0d3c45ebe4 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In this series patch, the interface kfree_skb_with_reason() is
introduced(), which is used to collect skb drop reason, and pass
it to 'kfree_skb' tracepoint. Therefor, 'drop_monitor' or eBPF is
able to monitor abnormal skb with detail reason.
In fact, this series patches are out of the intelligence of David
and Steve, I'm just a truck man :/
In the first patch, kfree_skb_with_reason() is introduced and
the 'reason' field is added to 'kfree_skb' tracepoint. In the
second patch, 'kfree_skb()' in replaced with 'kfree_skb_with_reason()'
in tcp_v4_rcv(). In the third patch, 'kfree_skb_with_reason()' is
used in __udp4_lib_rcv().
Changes since v3:
- fix some code style problems in skb.h
Changes since v2:
- rename kfree_skb_with_reason() to kfree_skb_reason()
- make kfree_skb() static inline, as Jakub suggested
Changes since v1:
- rename some drop reason, as David suggested
- add the third patch
====================
Jakub Kicinski [Sun, 9 Jan 2022 21:33:21 +0000 (13:33 -0800)]
net/mlx5e: Fix build error in fec_set_block_stats()
Build bot reports:
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c: In function 'fec_set_block_stats':
drivers/net/ethernet/mellanox/mlx5/core/en_stats.c:1235:48: error: 'outl' undeclared (first use in this function); did you mean 'out'?
1235 | if (mlx5_core_access_reg(mdev, in, sz, outl, sz, MLX5_REG_PPCNT, 0, 0))
| ^~~~
| out
Jakub Kicinski [Mon, 10 Jan 2022 00:27:26 +0000 (16:27 -0800)]
Merge branch 'bnxt_en-update-for-net-next'
Michael Chan says:
====================
bnxt_en: Update for net-next
This series adds better error and debug logging for firmware messages.
We now also use the firmware provided timeout value for long running
commands instead of capping it to 40 seconds.
====================
Edwin Peer [Sun, 9 Jan 2022 23:54:45 +0000 (18:54 -0500)]
bnxt_en: improve firmware timeout messaging
While it has always been possible to infer that an HWRM command was
abandoned due to an unhealthy firmware status by the shortened timeout
reported, this change improves the log messaging to account for this
case explicitly. In the interests of further clarity, the firmware
status is now also reported in these new messages.
v2: Remove inline keyword for hwrm_wait_must_abort() in .c file.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edwin Peer [Sun, 9 Jan 2022 23:54:44 +0000 (18:54 -0500)]
bnxt_en: use firmware provided max timeout for messages
Some older devices cannot accommodate the 40 seconds timeout
cap for long running commands (such as NVRAM commands) due to
hardware limitations. Allow these devices to request more time for
these long running commands, but print a warning, since the longer
timeout may cause the hung task watchdog to trigger. In the case of a
firmware update operation, this is preferable to failing outright.
v2: Use bp->hwrm_cmd_max_timeout directly without the constants.
Fixes: 436f374a3bfd ("bnxt_en: Add an upper bound for all firmware command timeouts.") Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edwin Peer [Sun, 9 Jan 2022 23:54:43 +0000 (18:54 -0500)]
bnxt_en: improve VF error messages when PF is unavailable
The current driver design relies on the PF netdev being open in order
to intercept the following HWRM commands from a VF:
- HWRM_FUNC_VF_CFG
- HWRM_CFA_L2_FILTER_ALLOC
- HWRM_PORT_PHY_QCFG (only if FW_CAP_LINK_ADMIN is not supported)
If the PF is closed, then VFs are subjected to rather inscrutable error
messages in response to any configuration requests involving the above
command types. Recent firmware distinguishes this problem case from
other errors by returning HWRM_ERR_CODE_PF_UNAVAILABLE. In most cases,
the appropriate course of action is still to fail, but this can now be
accomplished with the aid of more user informative log messages. For L2
filter allocations that are already asynchronous, an automatic retry
seems more appropriate.
v2: Delete extra newline.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Edwin Peer [Sun, 9 Jan 2022 23:54:42 +0000 (18:54 -0500)]
bnxt_en: add dynamic debug support for HWRM messages
Add logging of firmware messages. These can be useful for diagnosing
issues in the field, but due to their verbosity are only appropriate
at a debug message level.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paul Blakey [Thu, 6 Jan 2022 15:38:04 +0000 (17:38 +0200)]
net: openvswitch: Fix ct_state nat flags for conns arriving from tc
Netfilter conntrack maintains NAT flags per connection indicating
whether NAT was configured for the connection. Openvswitch maintains
NAT flags on the per packet flow key ct_state field, indicating
whether NAT was actually executed on the packet.
When a packet misses from tc to ovs the conntrack NAT flags are set.
However, NAT was not necessarily executed on the packet because the
connection's state might still be in NEW state. As such, openvswitch
wrongly assumes that NAT was executed and sets an incorrect flow key
NAT flags.
Fix this, by flagging to openvswitch which NAT was actually done in
act_ct via tc_skb_ext and tc_skb_cb to the openvswitch module, so
the packet flow key NAT flags will be correctly set.
Fixes: 1a23a38cf53c ("net/sched: Introduce action ct") Signed-off-by: Paul Blakey <paulb@nvidia.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/20220106153804.26451-1-paulb@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next. This
includes one patch to update ovs and act_ct to use nf_ct_put() instead
of nf_conntrack_put().
1) Add netns_tracker to nfnetlink_log and masquerade, from Eric Dumazet.
2) Remove redundant rcu read-size lock in nf_tables packet path.
3) Replace BUG() by WARN_ON_ONCE() in nft_payload.
4) Consolidate rule verdict tracing.
5) Replace WARN_ON() by WARN_ON_ONCE() in nf_tables core.
6) Make counter support built-in in nf_tables.
7) Add new field to conntrack object to identify locally generated
traffic, from Florian Westphal.
8) Prevent NAT from shadowing well-known ports, from Florian Westphal.
9) Merge nf_flow_table_{ipv4,ipv6} into nf_flow_table_inet, also from
Florian.
10) Remove redundant pointer in nft_pipapo AVX2 support, from Colin Ian King.
11) Replace opencoded max() in conntrack, from Jiapeng Chong.
12) Update conntrack to use refcount_t API, from Florian Westphal.
13) Move ip_ct_attach indirection into the nf_ct_hook structure.
14) Constify several pointer object in the netfilter codebase,
from Florian Westphal.
15) Tree-wide replacement of nf_conntrack_put() by nf_ct_put(), also
from Florian.
16) Fix egress splat due to incorrect rcu notation, from Florian.
17) Move stateful fields of connlimit, last, quota, numgen and limit
out of the expression data area.
18) Build a blob to represent the ruleset in nf_tables, this is a
requirement of the new register tracking infrastructure.
19) Add NFT_REG32_NUM to define the maximum number of 32-bit registers.
20) Add register tracking infrastructure to skip redundant
store-to-register operations, this includes support for payload,
meta and bitwise expresssions.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next: (32 commits)
netfilter: nft_meta: cancel register tracking after meta update
netfilter: nft_payload: cancel register tracking after payload update
netfilter: nft_bitwise: track register operations
netfilter: nft_meta: track register operations
netfilter: nft_payload: track register operations
netfilter: nf_tables: add register tracking infrastructure
netfilter: nf_tables: add NFT_REG32_NUM
netfilter: nf_tables: add rule blob layout
netfilter: nft_limit: move stateful fields out of expression data
netfilter: nft_limit: rename stateful structure
netfilter: nft_numgen: move stateful fields out of expression data
netfilter: nft_quota: move stateful fields out of expression data
netfilter: nft_last: move stateful fields out of expression data
netfilter: nft_connlimit: move stateful fields out of expression data
netfilter: egress: avoid a lockdep splat
net: prefer nf_ct_put instead of nf_conntrack_put
netfilter: conntrack: avoid useless indirection during conntrack destruction
netfilter: make function op structures const
netfilter: core: move ip_ct_attach indirection to struct nf_ct_hook
netfilter: conntrack: convert to refcount_t api
...
====================
Check if the destination register already contains the data that this
bitwise expression performs. This allows to skip this redundant
operation.
If the destination contains a different bitwise operation, cancel the
register tracking information. If the destination contains no bitwise
operation, update the register tracking information.
Update the payload and meta expression to check if this bitwise
operation has been already performed on the register. Hence, both the
payload/meta and the bitwise expressions are reduced.
There is also a special case: If source register != destination register
and source register is not updated by a previous bitwise operation, then
transfer selector from the source register to the destination register.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Check if the destination register already contains the data that this
meta store expression performs. This allows to skip this redundant
operation. If the destination contains a different selector, update
the register tracking information.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Check if the destination register already contains the data that this
payload store expression performs. This allows to skip this redundant
operation. If the destination contains a different selector, update
the register tracking information.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds new infrastructure to skip redundant selector store
operations on the same register to achieve a performance boost from
the packet path.
This is particularly noticeable in pure linear rulesets but it also
helps in rulesets which are already heaving relying in maps to avoid
ruleset linear inspection.
The idea is to keep data of the most recurrent store operations on
register to reuse them with cmp and lookup expressions.
This infrastructure allows for dynamic ruleset updates since the ruleset
blob reduction happens from the kernel.
Userspace still needs to be updated to maximize register utilization to
cooperate to improve register data reuse / reduce number of store on
register operations.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The new structure nft_rule_dp represents the rule in a more compact way
(smaller memory footprint) compared to the control-plane nft_rule
structure.
The ruleset blob is a read-only data structure. The first field contains
the blob size, then the rules containing expressions. There is a trailing
rule which is used by the tracing infrastructure which is equivalent to
the NULL rule marker in the previous representation. The blob size field
does not include the size of this trailing rule marker.
The ruleset blob is generated from the commit path.
This patch reuses the infrastructure available since 82560e53d11e
("netfilter: nf_tables: remove synchronize_rcu in commit phase") to
build the array of rules per chain.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Its the same as nf_conntrack_put(), but without the
need for an indirect call. The downside is a module dependency on
nf_conntrack, but all of these already depend on conntrack anyway.
Cc: Paul Blakey <paulb@mellanox.com> Cc: dev@openvswitch.org Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
There are two _put helpers:
nf_ct_put and nf_conntrack_put. The latter is what should be used in
code that MUST NOT cause a linker dependency on the conntrack module
(e.g. calls from core network stack).
Everyone else should call nf_ct_put() instead.
A followup patch will convert a few nf_conntrack_put() calls to
nf_ct_put(), in particular from modules that already have a conntrack
dependency such as act_ct or even nf_conntrack itself.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Convert nf_conn reference counting from atomic_t to refcount_t based api.
refcount_t api provides more runtime sanity checks and will warn on
certain constructs, e.g. refcount_inc() on a zero reference count, which
usually indicates use-after-free.
For this reason template allocation is changed to init the refcount to
1, the subsequenct add operations are removed.
Likewise, init_conntrack() is changed to set the initial refcount to 1
instead refcount_inc().
This is safe because the new entry is not (yet) visible to other cpus.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Jakub Kicinski [Sun, 9 Jan 2022 22:14:08 +0000 (14:14 -0800)]
Merge tag 'for-net-next-2022-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Foxconn QCA 0xe0d0
- Fix HCI init sequence on MacBook Air 8,1 and 8,2
- Fix Intel firmware loading on legacy ROM devices
* tag 'for-net-next-2022-01-07' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next:
Bluetooth: hci_sock: fix endian bug in hci_sock_setsockopt()
Bluetooth: L2CAP: uninitialized variables in l2cap_sock_setsockopt()
Bluetooth: btqca: sequential validation
Bluetooth: btusb: Add support for Foxconn QCA 0xe0d0
Bluetooth: btintel: Fix broken LED quirk for legacy ROM devices
Bluetooth: hci_event: Rework hci_inquiry_result_with_rssi_evt
Bluetooth: btbcm: disable read tx power for MacBook Air 8,1 and 8,2
Bluetooth: hci_qca: Fix NULL vs IS_ERR_OR_NULL check in qca_serdev_probe
Bluetooth: hci_bcm: Check for error irq
====================
Jakub Kicinski [Sun, 9 Jan 2022 22:00:49 +0000 (14:00 -0800)]
Merge tag 'linux-can-fixes-for-5.16-20220109' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-01-09
The first patch is by Johan Hovold and fixes a mem leak in the error
path of the softing_cs driver.
The next patch is by me and fixes a set but not used variable warning
in the softing driver.
Jiasheng Jiang's patch for the xilinx_can driver adds the missing
error checking when getting the IRQ.
Lad Prabhakar contributes a patch for the rcar_canfd driver to fix a
mem leak in the error path.
The last patch is by Brian Silverman and properly initializes the send
USB messages to avoid spurious CAN error frames.
* tag 'linux-can-fixes-for-5.16-20220109' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: gs_usb: gs_can_start_xmit(): zero-initialize hf->{flags,reserved}
can: rcar_canfd: rcar_canfd_channel_probe(): make sure we free CAN network device
can: xilinx_can: xcan_probe(): check for error irq
can: softing: softing_startstop(): fix set but not used variable warning
can: softing_cs: softingcs_probe(): fix memleak on registration failure
====================
this is a pull request of 22 patches for net-next/master.
The first patch is by Tom Rix and fixes an uninitialized variable in
the janz-ican3 driver (introduced in linux-can-next-for-5.17-20220105).
The next 13 patches are by my and target the mcp251xfd driver. First
several cleanup patches, then the driver is prepared for the upcoming
ethtool ring parameter and IRQ coalescing support, which is added in a
later pull request.
The remaining 8 patches are by Dario Binacchi and me and enhance the
flexcan driver. The driver is moved into a sub directory. An ethtool
private flag is added to optionally disable CAN RTR frame reception,
to make use of more RX buffers. The resulting RX buffer configuration
can be read by ethtool ring parameter support. Finally documentation
for the ethtool private flag is added to the
Documentation/networking/device_drivers/can directory.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
Lad Prabhakar [Thu, 6 Jan 2022 11:48:00 +0000 (11:48 +0000)]
can: rcar_canfd: rcar_canfd_channel_probe(): make sure we free CAN network device
Make sure we free CAN network device in the error path. There are
several jumps to fail label after allocating the CAN network device
successfully. This patch places the free_candev() under fail label so
that in failure path a jump to fail label frees the CAN network
device.
Fixes: 53f37e24dc63 ("can: rcar_canfd: Add support for RZ/G2L family") Link: https://lore.kernel.org/all/20220106114801.20563-1-prabhakar.mahadev-lad.rj@bp.renesas.com Reported-by: Pavel Machek <pavel@denx.de> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jiasheng Jiang [Fri, 24 Dec 2021 02:13:24 +0000 (10:13 +0800)]
can: xilinx_can: xcan_probe(): check for error irq
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq()
effectively convert that into -EINVAL, even at probe time rather than
later on. So it might be better to check just now.
can: softing: softing_startstop(): fix set but not used variable warning
In the function softing_startstop() the variable error_reporting is
assigned but not used. The code that uses this variable is commented
out. Its stated that the functionality is not finally verified.
To fix the warning:
| drivers/net/can/softing/softing_fw.c:424:9: error: variable 'error_reporting' set but not used [-Werror,-Wunused-but-set-variable]
remove the comment, activate the code, but add a "0 &&" to the if
expression and rely on the optimizer rather than the preprocessor to
remove the code.
Johan Hovold [Wed, 22 Dec 2021 10:48:43 +0000 (11:48 +0100)]
can: softing_cs: softingcs_probe(): fix memleak on registration failure
In case device registration fails during probe, the driver state and
the embedded platform device structure needs to be freed using
platform_device_put() to properly free all resources (e.g. the device
name).
Fixes: 680d8e2156c5 ("can: add driver for Softing card") Link: https://lore.kernel.org/all/20211222104843.6105-1-johan@kernel.org Cc: stable@vger.kernel.org # 2.6.38 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Dario Binacchi [Sat, 8 Jan 2022 18:16:33 +0000 (19:16 +0100)]
can: flexcan: add ethtool support to get rx/tx ring parameters
This patch adds ethtool support to get the number of message buffers
configured for reception/transmission, which may also depends on
runtime configurations such as the 'rx-rtr' flag state.
can: flexcan: add ethtool support to change rx-rtr setting during runtime
This patch adds a private flag to the flexcan driver to switch the
"rx-rtr" setting on and off.
"rx-rtr" on - Receive RTR frames. (default)
The CAN controller can and will receive RTR frames.
On some IP cores the controller cannot receive RTR
frames in the more performant "RX mailbox" mode and
will use "RX FIFO" mode instead.
"rx-rtr" off - Waive ability to receive RTR frames. (not supported on all IP cores)
This mode activates the "RX mailbox mode" for better
performance, on some IP cores RTR frames cannot be
received anymore.
The "RX FIFO" mode uses a FIFO with a depth of 6 CAN frames.
The "RX mailbox" mode uses up to 62 mailboxes.
can: flexcan: add more quirks to describe RX path capabilities
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
Some IP core versions cannot receive CAN RTR messages via mailboxes.
This patch adds quirks to document this.
This information will be used in a later patch to switch from FIFO to
more performant mailbox mode at the expense of losing the ability to
receive RTR messages. This trade off is beneficial in certain use
cases.
Most flexcan IP cores support 2 RX modes:
- FIFO
- mailbox
The names for these modes were chosen to reflect the name of the
rx-offload mode they are using.
The name of the RX modes should better reflect their difference with
regards the flexcan IP core. So this patch renames the various
occurrences of OFF_FIFO to RX_FIFO and OFF_TIMESTAMP to RX_MAILBOX:
can: mcp251xfd: mcp251xfd.h: sort function prototypes
The .c files in the Makefile are ordered alphabetically. This patch
groups the function prototypes by their corresponding .c file and
brings the into the same order.
A RX overflow usually happens during high system load. Printing
overflow messages to the kernel log, which on embedded systems often
is outputted on the serial console, even increases the system load.
To decrease the system load in these situations, denote the messages
to debug level and wrap them with net_ratelimit().
can: mcp251xfd: mcp251xfd_open(): make use of pm_runtime_resume_and_get()
With patch
| c4a28fe77ffc PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter
the usual pm_runtime_get_sync() and pm_runtime_put_noidle()
in-case-of-error dance is no longer needed. Convert the mcp251xfd
driver to use this function.
can: mcp251xfd: mcp251xfd_open(): open_candev() first
This patch exchanges the order of open_candev() and
pm_runtime_get_sync(), so that open_candev() is called first.
A usual reason why open_candev() fails is missing CAN bit rate
configuration. It makes no sense to resume the device from PM sleep
first just to put it to sleep if the bit rate is not configured.
Tom Rix [Sat, 8 Jan 2022 14:33:19 +0000 (06:33 -0800)]
can: janz-ican3: initialize dlc variable
Clang static analysis reports this problem
janz-ican3.c:1311:2: warning: Undefined or garbage value returned to caller
return dlc;
^~~~~~~~~~
dlc is only set with this conditional
if (!(cf->can_id & CAN_RTR_FLAG))
dlc = cf->len;
But is always returned. So initialize dlc to 0.
Fixes: b01d5543f78d ("can: do not increase tx_bytes statistics for RTR frames") Link: https://lore.kernel.org/all/20220108143319.3986923-1-trix@redhat.com Signed-off-by: Tom Rix <trix@redhat.com> Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
====================
ENA: capabilities field and cosmetic changes
Add a new capabilities bitmask field to get indication of
capabilities supported by the device. Use the capabilities
field to query the device for ENI stats support.
Other patches are cosmetic changes like fixing readme
mistakes, removing unused variables etc...
====================
This struct was used to pass data from callee function to its caller.
Its usage can be avoided.
Removing it results in less code without any damage to code readability.
Also it allows to consolidate ring size calculation into a single
function (ena_calc_io_queue_size()).
Signed-off-by: Shay Agroskin <shayagr@amazon.com> Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / kernel.git / log