Hoan Tran [Thu, 13 Oct 2016 17:33:35 +0000 (10:33 -0700)]
cpufreq: CPPC: Correct desired_perf calculation
The desired_perf is an abstract performance number. Its value should
be in the range of [lowest perf, highest perf] of CPPC.
The correct calculation is
desired_perf = freq * cppc_highest_perf / cppc_dmi_max_khz
And cppc_cpufreq_set_target() returns if desired_perf is exactly
the same with the old perf.
Signed-off-by: Hoan Tran <hotran@apm.com> Reviewed-by: Prashanth Prakash <pprakash@codeaurora.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: conservative: Fix next frequency selection
Commit d352cf47d93e (cpufreq: conservative: Do not use transition
notifications) overlooked the case when the "frequency step" used
by the conservative governor is small relative to the distances
between the available frequencies and broke the algorithm by
using policy->cur instead of the previously requested frequency
when computing the next one.
As a result, the governor may not be able to go outside of a narrow
range between two consecutive available frequencies.
Fix the problem by making the governor save the previously requested
frequency and select the next one relative that value (unless it is
out of range, in which case policy->cur will be used instead).
Fixes: d352cf47d93e (cpufreq: conservative: Do not use transition notifications) Link: https://bugzilla.kernel.org/show_bug.cgi?id=177171 Reported-and-tested-by: Aleksey Rybalkin <aleksey@rybalkin.org> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 4.8+ <stable@vger.kernel.org> # 4.8+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: intel_pstate: Proportional algorithm for Atom
The PID algorithm used by the intel_pstate driver tends to drive
performance to the minimum for workloads with utilization below the
setpoint, which is undesirable, so replace it with a modified
"proportional" algorithm on Atom.
The new algorithm will set the new P-state to be 1.25 times the
available maximum times the (frequency-invariant) utilization during
the previous sampling period except when the target P-state computed
this way is lower than the average P-state during the previous
sampling period. In the latter case, it will increase the target by
50% of the difference between it and the average P-state to prevent
performance from dropping down too fast in some cases.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
This is a requirement that MSR MSR_PM_ENABLE must be set to 0x01 before
reading MSR_HWP_CAPABILITIES on a given CPU. If cpufreq init() is
scheduled on a CPU which is not same as policy->cpu or migrates to a
different CPU before calling msr read for MSR_HWP_CAPABILITIES, it
is possible that MSR_PM_ENABLE was not to set to 0x01 on that CPU.
This will cause GP fault. So like other places in this path
rdmsrl_on_cpu should be used instead of rdmsrl.
Moreover the scope of MSR_HWP_CAPABILITIES is on per thread basis, so it
should be read from the same CPU, for which MSR MSR_HWP_REQUEST is
getting set.
Colin Ian King [Sun, 25 Sep 2016 21:40:13 +0000 (14:40 -0700)]
cpufreq: st: add missing \n to end of dev_err message
Trival fix, dev_err message is missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Colin Ian King [Sun, 25 Sep 2016 21:35:43 +0000 (14:35 -0700)]
cpufreq: kirkwood: add missing \n to end of dev_err messages
Trival fix, dev_err messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: CPPC: Avoid overflow when calculating desired_perf
This patch fixes overflow issue when calculating the desired_perf.
Fixes: ad38677df44b (cpufreq: CPPC: Force reporting values in KHz to fix user space interface) Signed-off-by: Hoan Tran <hotran@apm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dave Gerlach [Wed, 14 Sep 2016 20:41:37 +0000 (15:41 -0500)]
cpufreq: ti: Use generic platdev driver
Now that the cpufreq-dt-platdev is used to create the cpufreq-dt platform
device for all OMAP platforms and the platform code that did it
before has been removed, add ti,am33xx and ti,dra7xx to the machine list
in cpufreq-dt-platdev which had relied on the removed platform code to do
this previously.
Fixes: 7694ca6e1d6f (cpufreq: omap: Use generic platdev driver) Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Cc: 4.7+ <stable@vger.kernel.org> # 4.7+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: intel_pstate: Use IOWAIT flag in Atom algorithm
Modify the P-state selection algorithm for Atom processors to use
the new SCHED_CPUFREQ_IOWAIT flag instead of the questionable
get_cpu_iowait_time_us() function.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify the schedutil cpufreq governor to boost the CPU
frequency if the SCHED_CPUFREQ_IOWAIT flag is passed to
it via cpufreq_update_util().
If that happens, the frequency is set to the maximum during
the first update after receiving the SCHED_CPUFREQ_IOWAIT flag
and then the boost is reduced by half during each following update.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Looks-good-to: Steve Muckle <smuckle@linaro.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
cpufreq / sched: SCHED_CPUFREQ_IOWAIT flag to indicate iowait condition
Testing indicates that it is possible to improve performace
significantly without increasing energy consumption too much by
teaching cpufreq governors to bump up the CPU performance level if
the in_iowait flag is set for the task in enqueue_task_fair().
For this purpose, define a new cpufreq_update_util() flag
SCHED_CPUFREQ_IOWAIT and modify enqueue_task_fair() to pass that
flag to cpufreq_update_util() in the in_iowait case. That generally
requires cpufreq_update_util() to be called directly from there,
because update_load_avg() may not be invoked in that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Looks-good-to: Steve Muckle <smuckle@linaro.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Merge tag 'samsung-defconfig-schedutil-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into pm-cpufreq-sched
The schedutil cpufreq governor will be switched from tristate to bool. Fix
defconfigs.
* tag 'samsung-defconfig-schedutil-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: multi_v7_defconfig: Don't attempt to enable schedutil governor as module
ARM: exynos_defconfig: Don't attempt to enable schedutil governor as module
Al Stone [Wed, 20 Jul 2016 21:10:04 +0000 (15:10 -0600)]
cpufreq: CPPC: Force reporting values in KHz to fix user space interface
When CPPC is being used by ACPI on arm64, user space tools such as
cpupower report CPU frequency values from sysfs that are incorrect.
What the driver was doing was reporting the values given by ACPI tables
in whatever scale was used to provide them. However, the ACPI spec
defines the CPPC values as unitless abstract numbers. Internal kernel
structures such as struct perf_cap, in contrast, expect these values
to be in KHz. When these struct values get reported via sysfs, the
user space tools also assume they are in KHz, causing them to report
incorrect values (for example, reporting a CPU frequency of 1MHz when
it should be 1.8GHz).
The downside is that this approach has some assumptions:
(1) It relies on SMBIOS3 being used, *and* that the Max Frequency
value for a processor is set to a non-zero value.
(2) It assumes that all processors run at the same speed, or that
the CPPC values have all been scaled to reflect relative speed.
This patch retrieves the largest CPU Max Frequency from a type 4 DMI
record that it can find. This may not be an issue, however, as a
sampling of DMI data on x86 and arm64 indicates there is often only
one such record regardless. Since CPPC is relatively new, it is
unclear if the ACPI ASL will always be written to reflect any sort
of relative performance of processors of differing speeds.
(3) It assumes that performance and frequency both scale linearly.
For arm64 servers, this may be sufficient, but it does rely on
firmware values being set correctly. Hence, other approaches will
be considered in the future.
This has been tested on three arm64 servers, with and without DMI, with
and without CPPC support.
Signed-off-by: Al Stone <ahs3@redhat.com> Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq: create link to policy only for registered CPUs
If a cpufreq driver is registered very early in the boot stage (e.g.
registered from postcore_initcall()), then cpufreq core may generate
kernel warnings for it.
In this case, the CPUs are brought online, then the cpufreq driver is
registered, and then the CPU topology devices are registered. However,
by the time cpufreq_add_dev() gets called, the cpu device isn't stored
in the per-cpu variable (cpu_sys_devices,) which is read by
get_cpu_device().
So the cpufreq core fails to get device for the CPU, for which
cpufreq_add_dev() was called in the first place and we will hit a
WARN_ON(!cpu_dev).
Even if we reuse the 'dev' parameter passed to cpufreq_add_dev() to
avoid that warning, there might be other CPUs online that share the
policy with the cpu for which cpufreq_add_dev() is called. Eventually
get_cpu_device() will return NULL for them as well, and we will hit the
same WARN_ON() again.
In order to fix these issues, change cpufreq core to create links to the
policy for a cpu only when cpufreq_add_dev() is called for that CPU.
Reuse the 'real_cpus' mask to track that as well.
Note that cpufreq_remove_dev() already handles removal of the links for
individual CPUs and cpufreq_add_dev() has aligned with that now.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk> Tested-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Julia Lawall [Sun, 11 Sep 2016 13:06:01 +0000 (15:06 +0200)]
intel_pstate: constify local structures
For structure types defined in the same file or local header files, find
top-level static structure declarations that have the following
properties:
1. Never reassigned.
2. Address never taken
3. Not passed to a top-level macro call
4. No pointer or array-typed field passed to a function or stored in a
variable.
Declare structures having all of these properties as const.
Done using Coccinelle.
Based on a suggestion by Joe Perches <joe@perches.com>.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq-dt driver is also used for systems with multiple
clock/voltage domains for CPUs, i.e. multiple cpufreq policies in a
system.
And in such cases the platform users may want to enable "governor
tunables per policy". Support that via platform data, as not all users
of the driver would want that behavior.
Reported-by: Juri Lelli <Juri.Lelli@arm.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The cpufreq DT driver also supports systems that have multiple
clock/voltage domains for CPUs, i.e. multiple policy systems.
The description of the Kconfig entry was never updated after the driver
was modified to support such systems, fix it.
Reported-by: Juri Lelli <Juri.Lelli@arm.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jean Delvare [Fri, 9 Sep 2016 11:05:24 +0000 (13:05 +0200)]
MAINTAINERS: Add Documentation/cpu-freq/
I am told the cpufreq documentation updates should go to the PM list.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Jean Delvare [Thu, 8 Sep 2016 21:05:07 +0000 (23:05 +0200)]
cpufreq-stats: Minor documentation fix
The cpufreq-stats code can no longer be built as a module, so it now
appears with square brackets in menuconfig.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: 1aefc75b2449 (cpufreq: stats: Make the stats code non-modular) Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge tag 'dm-4.8-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable fix in both DM crypt and DM log-writes for too large bios
(as generated by bcache)
- two other stable fixes for DM log-writes
- a stable fix for a DM crypt bug that could result in freeing pointers
from uninitialized memory in the tfm allocation error path
- a DM bufio cleanup to discontinue using create_singlethread_workqueue()
* tag 'dm-4.8-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm bufio: remove use of deprecated create_singlethread_workqueue()
dm crypt: fix free of bad values after tfm allocation failure
dm crypt: fix error with too large bios
dm log writes: fix check of kthread_run() return value
dm log writes: fix bug with too large bios
dm log writes: move IO accounting earlier to fix error path
Merge branch 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I'm still prepping a set of fixes for btrfs fsync, just nailing down a
hard to trigger memory corruption. For now, these are tested and ready."
* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix one bug that process may endlessly wait for ticket in wait_reserve_ticket()
Btrfs: fix endless loop in balancing block groups
Btrfs: kill invalid ASSERT() in process_all_refs()
Merge tag 'char-misc-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of small driver fixes for 4.8-rc5.
The largest thing here is deleting an obsolete driver,
drivers/misc/bh1780gli.c, as the functionality of it was replaced by
an iio driver a while ago.
The other fixes are things that have been reported, or reverts of
broken stuff (the binder change). All of these changes have been in
linux-next for a while with no reported issues"
* tag 'char-misc-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
thunderbolt: Don't declare Falcon Ridge unsupported
thunderbolt: Add support for INTEL_FALCON_RIDGE_2C controller.
thunderbolt: Fix resume quirk for Falcon Ridge 4C.
lkdtm: Mark lkdtm_rodata_do_nothing() notrace
mei: me: disable driver on SPT SPS firmware
Revert "android: binder: fix dangling pointer comparison"
drivers/iio/light/Kconfig: SENSORS_BH1780 cleanup
android: binder: fix dangling pointer comparison
misc: delete bh1780 driver
Merge tag 'driver-core-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are three small fixes for 4.8-rc5.
One for sysfs, one for kernfs, and one documentation fix, all for
reported issues. All of these have been in linux-next for a while"
* tag 'driver-core-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: correctly handle read offset on PREALLOC attrs
documentation: drivers/core/of: fix name of of_node symlink
kernfs: don't depend on d_find_any_alias() when generating notifications
Merge tag 'tty-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are some small serial driver fixes for 4.8-rc5. One fixes an
oft-reported build issue with the fintek driver, another reverts a
patch that was causing problems, one fixes a crash, and some new
device ids were added.
All of these have been in linux-next for a while"
* tag 'tty-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: added acces i/o products quad and octal serial cards
serial: 8250_mid: fix divide error bug if baud rate is 0
Revert "tty/serial/8250: use mctrl_gpio helpers"
8250/fintek: rename IRQ_MODE macro
Merge tag 'usb-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are some USB and PHY driver fixes for 4.8-rc5
Nothing major, lots of little fixes for reported bugs, and a build fix
for a missing .h file that the phy drivers needed. All of these have
been in linux-next for a while with no reported issues"
* tag 'usb-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (24 commits)
usb: musb: Fix locking errors for host only mode
usb: dwc3: gadget: always decrement by 1
usb: dwc3: debug: fix ep name on trace output
usb: gadget: udc: core: don't starve DMA resources
USB: serial: option: add WeTelecom 0x6802 and 0x6803 products
USB: avoid left shift by -1
USB: fix typo in wMaxPacketSize validation
usb: gadget: Add the gserial port checking in gs_start_tx()
usb: dwc3: gadget: don't rely on jiffies while holding spinlock
usb: gadget: fsl_qe_udc: signedness bug in qe_get_frame()
usb: gadget: function: f_rndis: socket buffer may be NULL
usb: gadget: function: f_eem: socket buffer may be NULL
usb: renesas_usbhs: gadget: fix return value check in usbhs_mod_gadget_probe()
usb: dwc2: Add reset control to dwc2
usb: dwc3: core: allow device to runtime_suspend several times
usb: dwc3: pci: runtime_resume child device
USB: serial: option: add WeTelecom WM-D200
usb: chipidea: udc: don't touch DP when controller is in host mode
USB: serial: mos7840: fix non-atomic allocation in write path
USB: serial: mos7720: fix non-atomic allocation in write path
...
devpts: return NULL pts 'priv' entry for non-devpts nodes
In commit 8ead9dd54716 ("devpts: more pty driver interface cleanups") I
made devpts_get_priv() just return the dentry->fs_data directly. And
because I thought it wouldn't happen, I added a warning if you ever saw
a pts node that wasn't on devpts.
And no, that warning never triggered under any actual real use, but you
can trigger it by creating nonsensical pts nodes by hand.
So just revert the warning, and make devpts_get_priv() return NULL for
that case like it used to.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: stable@vger.kernel.org # 4.6+ Cc: Eric W Biederman" <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes for the nvme over fabrics code"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme-rdma: Get rid of redundant defines
nvme-rdma: Get rid of duplicate variable
nvme: fabrics drivers don't need the nvme-pci driver
nvme-fabrics: get a reference when reusing a nvme_host structure
nvme-fabrics: change NQN UUID to big-endian format
nvme-loop: set sqsize to 0-based value, per spec
nvme-rdma: fix sqsize/hsqsize per spec
fabrics: define admin sqsize min default, per spec
nvmet-rdma: +1 to *queue_size from hsqsize/hrqsize
nvmet-rdma: Fix use after free
nvme-rdma: initialize ret to zero to avoid returning garbage
Jarkko Sakkinen [Thu, 1 Sep 2016 23:36:58 +0000 (02:36 +0300)]
tpm: invalid self test error message
The driver emits invalid self test error message even though the init
succeeds.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Fixes: cae8b441fc20 ("tpm: Factor out common startup code") Reviewed-by: James Morris <james.l.morris@oracle.com> Signed-off-by: James Morris <james.l.morris@oracle.com>
Merge tag 'acpi-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes ffrom Rafael Wysocki:
"Two stable-candidate fixes for the ACPI early device probing code
added during the 4.4 cycle, one fixing a typo in a stub macro used
when CONFIG_ACPI is unset and one that prevents sleeping functions
from being called under a spinlock (Lorenzo Pieralisi)"
* tag 'acpi-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / drivers: replace acpi_probe_lock spinlock with mutex
ACPI / drivers: fix typo in ACPI_DECLARE_PROBE_ENTRY macro
Merge tag 'pm-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"This includes a stable-candidate cpufreq-dt driver problem fix and
annotations of tracepoints in the runtime PM framework.
Specifics:
- Fix the definition of the cpufreq-dt driver's machines table
introduced during the 4.7 cycle that should be NULL-terminated, but
the termination entry is missing from it (Wei Yongjun).
- Annotate tracepoints in the runtime PM framework's core so as to
allow the functions containing them to be called from the idle code
path without causing RCU to complain about illegal usage (Paul
McKenney)"
* tag 'pm-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Add _rcuidle suffix to allow rpm_idle() use from idle
PM / runtime: Add _rcuidle suffix to allow rpm_resume() to be called from idle
cpufreq: dt: Add terminate entry for of_device_id tables
Merge branches 'pm-cpufreq-fixes' and 'pm-core-fixes'
* pm-cpufreq-fixes:
cpufreq: dt: Add terminate entry for of_device_id tables
* pm-core-fixes:
PM / runtime: Add _rcuidle suffix to allow rpm_idle() use from idle
PM / runtime: Add _rcuidle suffix to allow rpm_resume() to be called from idle
ACPI / drivers: replace acpi_probe_lock spinlock with mutex
Commit e647b532275b ("ACPI: Add early device probing infrastructure")
introduced code that allows inserting driver specific
struct acpi_probe_entry probe entries into ACPI linker sections
(one per-subsystem, eg irqchip, clocksource) that are then walked
to retrieve the data and function hooks required to probe the
respective kernel components.
Probing for all entries in a section is triggered through
the __acpi_probe_device_table() function, that in turn, according
to the table ID a given probe entry reports parses the table
with the function retrieved from the respective section structures
(ie struct acpi_probe_entry). Owing to the current ACPI table
parsing implementation, the __acpi_probe_device_table() function
has to share global variables with the acpi_match_madt() function, so
in order to guarantee mutual exclusion locking is required
between the two functions.
Current kernel code implements the locking through the acpi_probe_lock
spinlock; this has the side effect of requiring all code called
within the lock (ie struct acpi_probe_entry.probe_{table/subtbl} hooks)
not to sleep.
However, kernel subsystems that make use of the early probing
infrastructure are relying on kernel APIs that may sleep (eg
irq_domain_alloc_fwnode(), among others) in the function calls
pointed at by struct acpi_probe_entry.{probe_table/subtbl} entries
(eg gic_v2_acpi_init()), which is a bug.
Since __acpi_probe_device_table() is called from context
that is allowed to sleep the acpi_probe_lock spinlock can be replaced
with a mutex; this fixes the issue whilst still guaranteeing
mutual exclusion.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Fixes: e647b532275b (ACPI: Add early device probing infrastructure) Cc: 4.4+ <stable@vger.kernel.org> # 4.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI / drivers: fix typo in ACPI_DECLARE_PROBE_ENTRY macro
When the ACPI_DECLARE_PROBE_ENTRY macro was added in
commit e647b532275b ("ACPI: Add early device probing infrastructure"),
a stub macro adding an unused entry was added for the !CONFIG_ACPI
Kconfig option case to make sure kernel code making use of the
macro did not require to be guarded within CONFIG_ACPI in order to
be compiled.
The stub macro was never used since all kernel code that defines
ACPI_DECLARE_PROBE_ENTRY entries is currently guarded within
CONFIG_ACPI; it contains a typo that should be nonetheless fixed.
Fix the typo in the stub (ie !CONFIG_ACPI) ACPI_DECLARE_PROBE_ENTRY()
macro so that it can actually be used if needed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Fixes: e647b532275b (ACPI: Add early device probing infrastructure) Cc: 4.4+ <stable@vger.kernel.org> # 4.4+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
x86/AMD: Apply erratum 665 on machines without a BIOS fix
AMD F12h machines have an erratum which can cause DIV/IDIV to behave
unpredictably. The workaround is to set MSRC001_1029[31] but sometimes
there is no BIOS update containing that workaround so let's do it
ourselves unconditionally. It is simple enough.
Steven Rostedt [Wed, 25 May 2016 17:47:26 +0000 (13:47 -0400)]
x86/paravirt: Do not trace _paravirt_ident_*() functions
Łukasz Daniluk reported that on a RHEL kernel that his machine would lock up
after enabling function tracer. I asked him to bisect the functions within
available_filter_functions, which he did and it came down to three:
_paravirt_nop(), _paravirt_ident_32() and _paravirt_ident_64()
It was found that this is only an issue when noreplace-paravirt is added
to the kernel command line.
This means that those functions are most likely called within critical
sections of the funtion tracer, and must not be traced.
In newer kenels _paravirt_nop() is defined within gcc asm(), and is no
longer an issue. But both _paravirt_ident_{32,64}() causes the
following splat when they are traced:
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Most of this is regression fixes for posix acl behavior introduced in
4.8-rc1 (these were caught by the pjd-fstest suite). The are also
miscellaneous fixes marked as stable material and cleanups.
Other than overlayfs code, it touches <linux/fs.h> to add a constant
with which to disable posix acl caching. No changes needed to the
actual caching code, it automatically does the right thing, although
later we may want to optimize this case.
I'm now testing overlayfs with the following test suites to catch
regressions:
- unionmount-testsuite
- xfstests
- pjd-fstest"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: update doc
ovl: listxattr: use strnlen()
ovl: Switch to generic_getxattr
ovl: copyattr after setting POSIX ACL
ovl: Switch to generic_removexattr
ovl: Get rid of ovl_xattr_noacl_handlers array
ovl: Fix OVL_XATTR_PREFIX
ovl: fix spelling mistake: "directries" -> "directories"
ovl: don't cache acl on overlay layer
ovl: use cached acl on underlying layer
ovl: proper cleanup of workdir
ovl: remove posix_acl_default from workdir
ovl: handle umask and posix_acl_default correctly on creation
ovl: don't copy up opaqueness
James Morse [Fri, 26 Aug 2016 15:03:42 +0000 (16:03 +0100)]
arm64: kernel: Fix unmasked debug exceptions when restoring mdscr_el1
Changes to make the resume from cpu_suspend() code behave more like
secondary boot caused debug exceptions to be unmasked early by
__cpu_setup(). We then go on to restore mdscr_el1 in cpu_do_resume(),
potentially taking break or watch points based on uninitialised registers.
Mask debug exceptions in cpu_do_resume(), which is specific to resume
from cpu_suspend(). Debug exceptions will be restored to their original
state by local_dbg_restore() in cpu_suspend(), which runs after
hw_breakpoint_restore() has re-initialised the other registers.
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Fixes: cabe1c81ea5b ("arm64: Change cpu_resume() to enable mmu early then access sleep_sp by va") Cc: <stable@vger.kernel.org> # 4.7+ Signed-off-by: James Morse <james.morse@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Stefan Wahren [Sat, 27 Aug 2016 16:19:50 +0000 (16:19 +0000)]
drivers/perf: arm_pmu: Fix NULL pointer dereference during probe
Patch 7f1d642fbb5c ("drivers/perf: arm-pmu: Fix handling of SPI lacking
interrupt-affinity property") unintended also fixes perf_event support
for bcm2835 which doesn't have PMU interrupts. Unfortunately this change
introduce a NULL pointer dereference on bcm2835, because irq_is_percpu
always expected to be called with a valid IRQ. So fix this regression
by validating the IRQ before.
Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 7f1d642fbb5c ("drivers/perf: arm-pmu: Fix handling of SPI lacking "interrupt-affinity" property") Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Merge tag 'dmaengine-fix-4.8-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"The fixes this time are all in drivers:
- possible NULL dereference in img-mdc
- correct device identity for free_irq in at_xdmac
- missing of_node_put() in fsl probe
- fix debug log and hotchain corner case for pxa-dma
- fix checking hardware bits in isr in usb dmac"
* tag 'dmaengine-fix-4.8-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: img-mdc: fix a possible NULL dereference
dmaengine: at_xdmac: fix to pass correct device identity to free_irq()
dmaengine: fsl_raid: add missing of_node_put() in fsl_re_probe()
dmaengine: pxa_dma: fix debug message
dmaengine: pxa_dma: fix hotchain corner case
dmaengine: usb-dmac: check CHCR.DE bit in usb_dmac_isr_channel()
Merge tag 'drm-fixes-for-4.8-rc5' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Contains fixes for imx, amdgpu, vc4, msm and one nouveau ACPI fix"
* tag 'drm-fixes-for-4.8-rc5' of git://people.freedesktop.org/~airlied/linux:
drm/amdgpu: record error code when ring test failed
drm/amd/amdgpu: compute ring test fail during S4 on CI
drm/amd/amdgpu: sdma resume fail during S4 on CI
drm/nouveau/acpi: use DSM if bridge does not support D3cold
drm/imx: fix crtc vblank state regression
drm/imx: Add active plane reconfiguration support
drm/msm: protect against faults from copy_from_user() in submit ioctl
drm/msm: fix use of copy_from_user() while holding spinlock
drm/vc4: Fix oops when userspace hands in a bad BO.
drm/vc4: Fix overflow mem unreferencing when the binner runs dry.
drm/vc4: Free hang state before destroying BO cache.
drm/vc4: Fix handling of a pm_runtime_get_sync() success case.
drm/vc4: Use drm_malloc_ab to fix large rendering jobs.
drm/vc4: Use drm_free_large() on handles to match its allocation.
Wanpeng Li [Fri, 2 Sep 2016 06:38:23 +0000 (14:38 +0800)]
tick/nohz: Fix softlockup on scheduler stalls in kvm guest
tick_nohz_start_idle() is prevented to be called if the idle tick can't
be stopped since commit 1f3b0f8243cb934 ("tick/nohz: Optimize nohz idle
enter"). As a result, after suspend/resume the host machine, full dynticks
kvm guest will softlockup:
The idle and iowait states are weird 0 for cpu0(housekeeping).
The bug is present in both guest and host kernels, and they both have
cpu0's idle and iowait states issue, however, host kernel's suspend/resume
path etc will touch watchdog to avoid the softlockup.
- The watchdog will not be touched in tick_nohz_stop_idle path (need be
touched since the scheduler stall is expected) if idle_active flags are
not detected.
- The idle and iowait states will not be accounted when exit idle loop
(resched or interrupt) if idle start time and idle_active flags are
not set.
This patch fixes it by reverting commit 1f3b0f8243cb934 since can't stop
idle tick doesn't mean can't be idle.
Fixes: 1f3b0f8243cb934 ("tick/nohz: Optimize nohz idle enter") Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Cc: Sanjeev Yadav<sanjeev.yadav@spreadtrum.com> Cc: Gaurav Jindal<gaurav.jindal@spreadtrum.com> Cc: stable@vger.kernel.org Cc: kvm@vger.kernel.org Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Link: http://lkml.kernel.org/r/1472798303-4154-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Dave Airlie [Fri, 2 Sep 2016 05:55:15 +0000 (15:55 +1000)]
Merge tag 'drm-vc4-fixes-2016-08-29' of https://github.com/anholt/linux into drm-fixes
This pull request brings in fixes for VC4 3D in 4.8, most of which are
covered by testcases.
* tag 'drm-vc4-fixes-2016-08-29' of https://github.com/anholt/linux:
drm/vc4: Fix oops when userspace hands in a bad BO.
drm/vc4: Fix overflow mem unreferencing when the binner runs dry.
drm/vc4: Free hang state before destroying BO cache.
drm/vc4: Fix handling of a pm_runtime_get_sync() success case.
drm/vc4: Use drm_malloc_ab to fix large rendering jobs.
drm/vc4: Use drm_free_large() on handles to match its allocation.
Dave Airlie [Fri, 2 Sep 2016 05:48:38 +0000 (15:48 +1000)]
Merge tag 'imx-drm-fixes-2016-08-30' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm atomic modeset regression fixes
- add active plane reconfiguration support
- add back crtc vblank state reporting
* tag 'imx-drm-fixes-2016-08-30' of git://git.pengutronix.de/git/pza/linux:
drm/imx: fix crtc vblank state regression
drm/imx: Add active plane reconfiguration support
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A collection of small fixes for various SoC vendor clk drivers"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: rockchip: mark aclk_emmc_noc as a critical clock on rk3399
clk: tegra: remove TEGRA_PLL_USE_LOCK for PLLD/PLLD2
clk: rockchip: fix incorrect GATE bits for {c, g}pll_aclk_perihp_src on rk3399
clk: rockchip: fix incorrect aclk_emmc source gate bits on rk3399
clk: renesas: r8a7795: Fix SD clocks
clk: rockchip: fix rk3399 aclk_vio gate bit
clk: sunxi-ng: Fix inverted test condition in ccu_helper_wait_for_lock
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
rapidio/tsi721: fix incorrect detection of address translation condition
rapidio/documentation/mport_cdev: add missing parameter description
kernel/fork: fix CLONE_CHILD_CLEARTID regression in nscd
MAINTAINERS: Vladimir has moved
mm, mempolicy: task->mempolicy must be NULL before dropping final reference
printk/nmi: avoid direct printk()-s from __printk_nmi_flush()
treewide: remove references to the now unnecessary DEFINE_PCI_DEVICE_TABLE
drivers/scsi/wd719x.c: remove last declaration using DEFINE_PCI_DEVICE_TABLE
mm, vmscan: only allocate and reclaim from zones with pages managed by the buddy allocator
lib/test_hash.c: fix warning in preprocessor symbol evaluation
lib/test_hash.c: fix warning in two-dimensional array init
kconfig: tinyconfig: provide whole choice blocks to avoid warnings
kexec: fix double-free when failing to relocate the purgatory
mm, oom: prevent premature OOM killer invocation for high order request
Michal Hocko [Thu, 1 Sep 2016 23:15:13 +0000 (16:15 -0700)]
kernel/fork: fix CLONE_CHILD_CLEARTID regression in nscd
Commit fec1d0115240 ("[PATCH] Disable CLONE_CHILD_CLEARTID for abnormal
exit") has caused a subtle regression in nscd which uses
CLONE_CHILD_CLEARTID to clear the nscd_certainly_running flag in the
shared databases, so that the clients are notified when nscd is
restarted. Now, when nscd uses a non-persistent database, clients that
have it mapped keep thinking the database is being updated by nscd, when
in fact nscd has created a new (anonymous) one (for non-persistent
databases it uses an unlinked file as backend).
The original proposal for the CLONE_CHILD_CLEARTID change claimed
(https://lkml.org/lkml/2006/10/25/233):
: The NPTL library uses the CLONE_CHILD_CLEARTID flag on clone() syscalls
: on behalf of pthread_create() library calls. This feature is used to
: request that the kernel clear the thread-id in user space (at an address
: provided in the syscall) when the thread disassociates itself from the
: address space, which is done in mm_release().
:
: Unfortunately, when a multi-threaded process incurs a core dump (such as
: from a SIGSEGV), the core-dumping thread sends SIGKILL signals to all of
: the other threads, which then proceed to clear their user-space tids
: before synchronizing in exit_mm() with the start of core dumping. This
: misrepresents the state of process's address space at the time of the
: SIGSEGV and makes it more difficult for someone to debug NPTL and glibc
: problems (misleading him/her to conclude that the threads had gone away
: before the fault).
:
: The fix below is to simply avoid the CLONE_CHILD_CLEARTID action if a
: core dump has been initiated.
The resulting patch from Roland (https://lkml.org/lkml/2006/10/26/269)
seems to have a larger scope than the original patch asked for. It
seems that limitting the scope of the check to core dumping should work
for SIGSEGV issue describe above.
[Changelog partly based on Andreas' description] Fixes: fec1d0115240 ("[PATCH] Disable CLONE_CHILD_CLEARTID for abnormal exit") Link: http://lkml.kernel.org/r/1471968749-26173-1-git-send-email-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Tested-by: William Preston <wpreston@suse.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Roland McGrath <roland@hack.frob.com> Cc: Andreas Schwab <schwab@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Thu, 1 Sep 2016 23:15:07 +0000 (16:15 -0700)]
mm, mempolicy: task->mempolicy must be NULL before dropping final reference
KASAN allocates memory from the page allocator as part of
kmem_cache_free(), and that can reference current->mempolicy through any
number of allocation functions. It needs to be NULL'd out before the
final reference is dropped to prevent a use-after-free bug:
BUG: KASAN: use-after-free in alloc_pages_current+0x363/0x370 at addr ffff88010b48102c
CPU: 0 PID: 15425 Comm: trinity-c2 Not tainted 4.8.0-rc2+ #140
...
Call Trace:
dump_stack
kasan_object_err
kasan_report_error
__asan_report_load2_noabort
alloc_pages_current <-- use after free
depot_save_stack
save_stack
kasan_slab_free
kmem_cache_free
__mpol_put <-- free
do_exit
This patch sets current->mempolicy to NULL before dropping the final
reference.
printk/nmi: avoid direct printk()-s from __printk_nmi_flush()
__printk_nmi_flush() can be called from nmi_panic(), therefore it has to
test whether it's executed in NMI context and thus must route the
messages through deferred printk() or via direct printk().
This is to avoid potential deadlocks, as described in commit cf9b1106c81c ("printk/nmi: flush NMI messages on the system panic").
However there remain two places where __printk_nmi_flush() does
unconditional direct printk() calls:
Factor out print_nmi_seq_line() parts into a new printk_nmi_flush_line()
function, which takes care of in_nmi(), and use it in
__printk_nmi_flush() for printing and error-reporting.
Link: http://lkml.kernel.org/r/20160830161354.581-1-sergey.senozhatsky@gmail.com Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm, vmscan: only allocate and reclaim from zones with pages managed by the buddy allocator
Firmware Assisted Dump (FA_DUMP) on ppc64 reserves substantial amounts
of memory when booting a secondary kernel. Srikar Dronamraju reported
that multiple nodes may have no memory managed by the buddy allocator
but still return true for populated_zone().
Commit 1d82de618ddd ("mm, vmscan: make kswapd reclaim in terms of
nodes") was reported to cause kswapd to spin at 100% CPU usage when
fadump was enabled. The old code happened to deal with the situation of
a populated node with zero free pages by co-incidence but the current
code tries to reclaim populated zones without realising that is
impossible.
We cannot just convert populated_zone() as many existing users really
need to check for present_pages. This patch introduces a managed_zone()
helper and uses it in the few cases where it is critical that the check
is made for managed pages -- zonelist construction and page reclaim.
lib/test_hash.c: fix warning in preprocessor symbol evaluation
Some versions of gcc don't like tests for the value of an undefined
preprocessor symbol, even in the #else branch of an #ifndef:
lib/test_hash.c:224:7: warning: "HAVE_ARCH__HASH_32" is not defined [-Wundef]
#elif HAVE_ARCH__HASH_32 != 1
^
lib/test_hash.c:229:7: warning: "HAVE_ARCH_HASH_32" is not defined [-Wundef]
#elif HAVE_ARCH_HASH_32 != 1
^
lib/test_hash.c:234:7: warning: "HAVE_ARCH_HASH_64" is not defined [-Wundef]
#elif HAVE_ARCH_HASH_64 != 1
^
Seen with gcc 4.9, not seen with 4.1.2.
Change the logic to only check the value inside an #ifdef to fix this.
Fixes: 468a9428521e7d00 ("<linux/hash.h>: Add support for architecture-specific functions") Link: http://lkml.kernel.org/r/20160829214952.1334674-4-arnd@arndb.de Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: George Spelvin <linux@sciencehorizons.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kconfig: tinyconfig: provide whole choice blocks to avoid warnings
Using "make tinyconfig" produces a couple of annoying warnings that show
up for build test machines all the time:
.config:966:warning: override: NOHIGHMEM changes choice state
.config:965:warning: override: SLOB changes choice state
.config:963:warning: override: KERNEL_XZ changes choice state
.config:962:warning: override: CC_OPTIMIZE_FOR_SIZE changes choice state
.config:933:warning: override: SLOB changes choice state
.config:930:warning: override: CC_OPTIMIZE_FOR_SIZE changes choice state
.config:870:warning: override: SLOB changes choice state
.config:868:warning: override: KERNEL_XZ changes choice state
.config:867:warning: override: CC_OPTIMIZE_FOR_SIZE changes choice state
I've made a previous attempt at fixing them and we discussed a number of
alternatives.
I tried changing the Makefile to use "merge_config.sh -n
$(fragment-list)" but couldn't get that to work properly.
This is yet another approach, based on the observation that we do want
to see a warning for conflicting 'choice' options, and that we can
simply make them non-conflicting by listing all other options as
disabled. This is a trivial patch that we can apply independent of
plans for other changes.
kexec: fix double-free when failing to relocate the purgatory
If kexec_apply_relocations fails, kexec_load_purgatory frees pi->sechdrs
and pi->purgatory_buf. This is redundant, because in case of error
kimage_file_prepare_segments calls kimage_file_post_load_cleanup, which
will also free those buffers.
This causes two warnings like the following, one for pi->sechdrs and the
other for pi->purgatory_buf:
kexec-bzImage64: Loading purgatory failed
------------[ cut here ]------------
WARNING: CPU: 1 PID: 2119 at mm/vmalloc.c:1490 __vunmap+0xc1/0xd0
Trying to vfree() nonexistent vm area (ffffc90000e91000)
Modules linked in:
CPU: 1 PID: 2119 Comm: kexec Not tainted 4.8.0-rc3+ #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x4d/0x65
__warn+0xcb/0xf0
warn_slowpath_fmt+0x4f/0x60
? find_vmap_area+0x19/0x70
? kimage_file_post_load_cleanup+0x47/0xb0
__vunmap+0xc1/0xd0
vfree+0x2e/0x70
kimage_file_post_load_cleanup+0x5e/0xb0
SyS_kexec_file_load+0x448/0x680
? putname+0x54/0x60
? do_sys_open+0x190/0x1f0
entry_SYSCALL_64_fastpath+0x13/0x8f
---[ end trace 158bb74f5950ca2b ]---
Fix by setting pi->sechdrs an pi->purgatory_buf to NULL, since vfree
won't try to free a NULL pointer.
Link: http://lkml.kernel.org/r/1472083546-23683-1-git-send-email-bauerman@linux.vnet.ibm.com Signed-off-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Dave Young <dyoung@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 1 Sep 2016 23:14:41 +0000 (16:14 -0700)]
mm, oom: prevent premature OOM killer invocation for high order request
There have been several reports about pre-mature OOM killer invocation
in 4.7 kernel when order-2 allocation request (for the kernel stack)
invoked OOM killer even during basic workloads (light IO or even kernel
compile on some filesystems). In all reported cases the memory is
fragmented and there are no order-2+ pages available. There is usually
a large amount of slab memory (usually dentries/inodes) and further
debugging has shown that there are way too many unmovable blocks which
are skipped during the compaction. Multiple reporters have confirmed
that the current linux-next which includes [1] and [2] helped and OOMs
are not reproducible anymore.
A simpler fix for the late rc and stable is to simply ignore the
compaction feedback and retry as long as there is a reclaim progress and
we are not getting OOM for order-0 pages. We already do that for
CONFING_COMPACTION=n so let's reuse the same code when compaction is
enabled as well.
Merge branch 'stable-4.8' of git://git.infradead.org/users/pcmoore/audit
Pull audit fixes from Paul Moore:
"Two small patches to fix some bugs with the audit-by-executable
functionality we introduced back in v4.3 (both patches are marked
for the stable folks)"
* 'stable-4.8' of git://git.infradead.org/users/pcmoore/audit:
audit: fix exe_file access in audit_exe_compare
mm: introduce get_task_exe_file
Merge tag 'xfs-iomap-for-linus-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs and iomap fixes from Dave Chinner:
"Most of these changes are small regression fixes that address problems
introduced in the 4.8-rc1 window. The two fixes that aren't (IO
completion fix and superblock inprogress check) are fixes for problems
introduced some time ago and need to be pushed back to stable kernels.
* tag 'xfs-iomap-for-linus-4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: track log done items directly in the deferred pending work item
iomap: don't set FIEMAP_EXTENT_MERGED for extent based filesystems
xfs: prevent dropping ioend completions during buftarg wait
xfs: fix superblock inprogress check
xfs: simple btree query range should look right if LE lookup fails
xfs: fix some key handling problems in _btree_simple_query_range
xfs: don't log the entire end of the AGF
xfs: disallow mounting of realtime + rmap filesystems
xfs: don't perform lookups on zero-height btrees
Wang Xiaoguang [Wed, 31 Aug 2016 11:46:16 +0000 (19:46 +0800)]
btrfs: fix one bug that process may endlessly wait for ticket in wait_reserve_ticket()
If can_overcommit() in btrfs_calc_reclaim_metadata_size() returns true,
btrfs_async_reclaim_metadata_space() will not reclaim metadata space, just
return directly and also forget to wake up process which are waiting for
their tickets, so these processes will wait endlessly.
Fstests case generic/172 with mount option "-o compress=lzo" have revealed
this bug in my test machine. Here if we have tickets to handle, we must
handle them first.
Signed-off-by: Wang Xiaoguang <wangxg.fnst@cn.fujitsu.com> Reviewed-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Wed, 31 Aug 2016 23:43:33 +0000 (16:43 -0700)]
Btrfs: fix endless loop in balancing block groups
Qgroup function may overwrite the saved error 'err' with 0
in case quota is not enabled, and this ends up with a
endless loop in balance because we keep going back to balance
the same block group.
It really should use 'ret' instead.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: David Sterba <dsterba@suse.com>
Josef Bacik [Wed, 24 Aug 2016 15:57:52 +0000 (11:57 -0400)]
Btrfs: kill invalid ASSERT() in process_all_refs()
Suppose you have the following tree in snap1 on a file system mounted with -o
inode_cache so that inode numbers are recycled
└── [ 258] a
└── [ 257] b
and then you remove b, rename a to c, and then re-create b in c so you have the
following tree
└── [ 258] c
└── [ 257] b
and then you try to do an incremental send you will hit
ASSERT(pending_move == 0);
in process_all_refs(). This is because we assume that any recycling of inodes
will not have a pending change in our path, which isn't the case. This is the
case for the DELETE side, since we want to remove the old file using the old
path, but on the create side we could have a pending move and need to do the
normal pending rename dance. So remove this ASSERT() and put a comment about
why we ignore pending_move. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com>
Be defensive about what underlying fs provides us in the returned xattr
list buffer. If it's not properly null terminated, bail out with a warning
insead of BUG.
Commit d837a49bd57f ("ovl: fix POSIX ACL setting") switches from
iop->setxattr from ovl_setxattr to generic_setxattr, so switch from
ovl_removexattr to generic_removexattr as well. As far as permission
checking goes, the same rules should apply in either case.
While doing that, rename ovl_setxattr to ovl_xattr_set to indicate that
this is not an iop->setxattr implementation and remove the unused inode
argument.
Move ovl_other_xattr_set above ovl_own_xattr_set so that they match the
order of handlers in ovl_xattr_handlers.
Use an ordinary #ifdef to conditionally include the POSIX ACL handlers
in ovl_xattr_handlers, like the other filesystems do. Flag the code
that is now only used conditionally with __maybe_unused.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Some operations (setxattr/chmod) can make the cached acl stale. We either
need to clear overlay's acl cache for the affected inode or prevent acl
caching on the overlay altogether. Preventing caching has the following
advantages:
- no double caching, less memory used
- overlay cache doesn't go stale when fs clears it's own cache
Possible disadvantage is performance loss. If that becomes a problem
get_acl() can be optimized for overlayfs.
This patch disables caching by pre setting i_*acl to a value that
- has bit 0 set, so is_uncached_acl() will return true
- is not equal to ACL_NOT_CACHED, so get_acl() will not overwrite it
When mounting overlayfs it needs a clean "work" directory under the
supplied workdir.
Previously the mount code removed this directory if it already existed and
created a new one. If the removal failed (e.g. directory was not empty)
then it fell back to a read-only mount not using the workdir.
While this has never been reported, it is possible to get a non-empty
"work" dir from a previous mount of overlayfs in case of crash in the
middle of an operation using the work directory.
In this case the left over state should be discarded and the overlay
filesystem will be consistent, guaranteed by the atomicity of operations on
moving to/from the workdir to the upper layer.
This patch implements cleaning out any files left in workdir. It is
implemented using real recursion for simplicity, but the depth is limited
to 2, because the worst case is that of a directory containing whiteouts
under "work".
ovl: handle umask and posix_acl_default correctly on creation
Setting MS_POSIXACL in sb->s_flags has the side effect of passing mode to
create functions without masking against umask.
Another problem when creating over a whiteout is that the default posix acl
is not inherited from the parent dir (because the real parent dir at the
time of creation is the work directory).
Fix these problems by:
a) If upper fs does not have MS_POSIXACL, then mask mode with umask.
b) If creating over a whiteout, call posix_acl_create() to get the
inherited acls. After creation (but before moving to the final
destination) set these acls on the created file. posix_acl_create() also
updates the file creation mode as appropriate.
Steve Muckle [Fri, 26 Aug 2016 18:40:47 +0000 (11:40 -0700)]
cpufreq / sched: ignore SMT when determining max cpu capacity
PELT does not consider SMT when scaling its utilization values via
arch_scale_cpu_capacity(). The value in rq->cpu_capacity_orig does
take SMT into consideration though and therefore may be smaller than
the utilization reported by PELT.
On an Intel i7-3630QM for example rq->cpu_capacity_orig is 589 but
util_avg scales up to 1024. This means that a 50% utilized CPU will show
up in schedutil as ~86% busy.
Fix this by using the same CPU scaling value in schedutil as that which
is used by PELT.
Signed-off-by: Steve Muckle <smuckle@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dave Airlie [Wed, 31 Aug 2016 20:34:09 +0000 (06:34 +1000)]
Merge branch 'msm-fixes-4.8' of git://people.freedesktop.org/~robclark/linux into drm-fixes
copy from user fixes.
* 'msm-fixes-4.8' of git://people.freedesktop.org/~robclark/linux:
drm/msm: protect against faults from copy_from_user() in submit ioctl
drm/msm: fix use of copy_from_user() while holding spinlock
Mateusz Guzik [Tue, 23 Aug 2016 14:20:39 +0000 (16:20 +0200)]
audit: fix exe_file access in audit_exe_compare
Prior to the change the function would blindly deference mm, exe_file
and exe_file->f_inode, each of which could have been NULL or freed.
Use get_task_exe_file to safely obtain stable exe_file.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com> Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Richard Guy Briggs <rgb@redhat.com> Cc: <stable@vger.kernel.org> # 4.3.x Signed-off-by: Paul Moore <paul@paul-moore.com>
Mateusz Guzik [Tue, 23 Aug 2016 14:20:38 +0000 (16:20 +0200)]
mm: introduce get_task_exe_file
For more convenient access if one has a pointer to the task.
As a minor nit take advantage of the fact that only task lock + rcu are
needed to safely grab ->exe_file. This saves mm refcount dance.
Use the helper in proc_exe_link.
Signed-off-by: Mateusz Guzik <mguzik@redhat.com> Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Acked-by: Richard Guy Briggs <rgb@redhat.com> Cc: <stable@vger.kernel.org> # 4.3.x Signed-off-by: Paul Moore <paul@paul-moore.com>
Dave Airlie [Wed, 31 Aug 2016 20:03:35 +0000 (06:03 +1000)]
Merge branch 'drm-fixes-4.8' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.8:
- 2 CI S4 fixes
- error handling fix
* 'drm-fixes-4.8' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: record error code when ring test failed
drm/amd/amdgpu: compute ring test fail during S4 on CI
drm/amd/amdgpu: sdma resume fail during S4 on CI
Chunming Zhou [Tue, 30 Aug 2016 09:59:11 +0000 (17:59 +0800)]
drm/amdgpu: record error code when ring test failed
Otherwise we may miss errors.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org