David S. Miller [Fri, 30 Aug 2019 00:47:27 +0000 (17:47 -0700)]
Merge branch 'r8169-add-support-for-RTL8125'
Heiner Kallweit says:
====================
r8169: add support for RTL8125
This series adds support for the 2.5Gbps chip RTl8125. It can be found
on PCIe network cards, and on an increasing number of consumer gaming
mainboards. Series is partially based on the r8125 vendor driver.
Tested with a Delock 89531 PCIe card against a Netgear GS110MX
Multi-Gig switch.
Firmware isn't strictly needed, but on some systems there may be
compatibility issues w/o firmware. Firmware has been submitted to
linux-firmware.
v2:
- split first patch into 6 smaller ones to facilitate bisecting
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 28 Aug 2019 20:29:05 +0000 (22:29 +0200)]
r8169: add support for EEE on RTL8125
This adds EEE support for RTL8125 based on the vendor driver.
Supported is EEE for 100Mbps and 1Gbps. Realtek recommended to not yet
enable EEE for 2.5Gbps due to potential compatibility issues. Also
ethtool doesn't support yet controlling EEE for 2.5Gbps and 5Gbps.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 28 Aug 2019 20:28:32 +0000 (22:28 +0200)]
r8169: add RTL8125 PHY initialization
This patch adds PHY initialization magic copied from the r8125 vendor
driver. In addition it supports loading the firmware for chip version
RTL_GIGA_MAC_VER_61.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 28 Aug 2019 20:28:03 +0000 (22:28 +0200)]
r8169: add support for RTL8125
This adds support for 2.5Gbps chip RTL8125, it's partially based on the
r8125 vendor driver. Tested with a Delock 89531 PCIe card against a
Netgear GS110MX Multi-Gig switch. Firmware isn't strictly needed,
but on some systems there may be compatibility issues w/o firmware.
Firmware has been submitted to linux-firmware.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 28 Aug 2019 20:26:51 +0000 (22:26 +0200)]
r8169: read common register for PCI commit
RTL8125 uses a different register number for IntrMask.
To net have side effects by reading a random register let's
use a register that is the same on all supported chip families.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 28 Aug 2019 20:24:13 +0000 (22:24 +0200)]
r8169: change interrupt mask type to u32
RTL8125 uses a 32 bit interrupt mask even though only bits in the
lower 16 bits are used. Change interrupt mask size to u32 to be
prepared and reintroduce helper rtl_get_events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Aug 2019 00:25:18 +0000 (17:25 -0700)]
Merge tag 'mlx5-updates-2019-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-08-22
Misc updates for mlx5e net device driver
1) Maxim and Tariq add the support for LAG TX port affinity distribution
When VF LAG is enabled, VFs netdevs will round-robin the TX affinity
of their tx queues among the different LAG ports.
2) Aya adds the support for ip-in-ip RSS.
3) Marina adds the support for ip-in-ip TX TSO and checksum offloads.
4) Moshe adds a device internal drop counter to mlx5 ethtool stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now mv88e6xxx does not enable its ports at setup itself and let
the DSA core handle this, unused ports are disabled without being
powered on first. While that is expected, the SERDES powering code
was assuming that a port was already set up before powering it down,
resulting in freeing an unused IRQ. The patch fixes this assumption.
Fixes: 0a9fc39ab7a3 ("net: dsa: mv88e6xxx: enable SERDES after setup") Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Marek Behún <marek.behun@nic.cz> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
This is a follow-up patch for commit 5a2edc8a6943 ("net: dsa:
mv88e6xxx: fully support SERDES on Topaz family").
Since .port_set_cmode is only called from mv88e6xxx_port_setup_mac and
mv88e6xxx_phylink_mac_config, it is fine to keep this "make writable"
code private to the mv88e6341_port_set_cmode implementation, instead
of adding yet another operation to the switch info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Wed, 28 Aug 2019 16:26:11 +0000 (12:26 -0400)]
net: dsa: mv88e6xxx: get serdes lane after lock
This is a follow-up patch for commit 4e3bd5e755d8 ("net: dsa:
mv88e6xxx: create serdes_get_lane chip operation").
The .serdes_get_lane implementations access the CMODE of a port,
even though it is cached at the moment, it is safer to call them
after the mutex is locked, not before.
At the same time, check for an eventual error and return IRQ_DONE,
instead of blindly ignoring it.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Wed, 28 Aug 2019 14:23:16 +0000 (22:23 +0800)]
net: hns3: not allow SSU loopback while execute ethtool -t dev
The current loopback mode is to add 0x1F to the SMAC address
as the DMAC address and enable the promiscuous mode.
However, if the VF address is the same as the DMAC address,
the loopback test fails.
Loopback can be enabled in three places: SSU, MAC, and serdes.
By default, SSU loopback is enabled, so if the SMAC and the DMAC
are the same, the packets are looped back in the SSU. If SSU loopback
is disabled, packets can reach MAC even if SMAC is the same as DMAC.
Therefore, this patch disables the SSU loopback before the loopback
test. In this way, the SMAC and DMAC can be the same, and the
promiscuous mode does not need to be enabled. And this is not
valid in version 0x20.
This patch also uses a macro to replace 0x1F.
Fixes: b598c1a72a4c ("net: hns3: Add mac loopback selftest support in hns3 driver") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Reviewed-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 28 Aug 2019 14:23:15 +0000 (22:23 +0800)]
net: hns3: check reset interrupt status when reset fails
Currently, the reset interrupt will be cleared firstly, so when
reset fails, if interrupt status register has reset interrupt,
it means there is a new coming reset.
Fixes: 70fbd6b4a837 ("net: hns3: clear reset interrupt status in hclge_irq_handle()") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Reviewed-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Wed, 28 Aug 2019 14:23:14 +0000 (22:23 +0800)]
net: hns3: add phy selftest function
Currently, the loopback test supports only mac selftest and serdes
selftest. This patch adds phy selftest.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Wed, 28 Aug 2019 14:23:13 +0000 (22:23 +0800)]
net: hns3: implement .process_hw_error for hns3 client
When hardware or IMP get specified error it may need the client
to take some special operations.
This patch implements the hns3 client's process_hw_errorx.
Signed-off-by: Weihang Li <liweihang@hisilicon.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Reviewed-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhongzhu Liu [Wed, 28 Aug 2019 14:23:12 +0000 (22:23 +0800)]
net: hns3: optimize waiting time for TQP reset
This patch optimizes the waiting time for TQP reset.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com> Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com> Reviewed-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guojia Liao [Wed, 28 Aug 2019 14:23:11 +0000 (22:23 +0800)]
net: hns3: fix incorrect type in assignment.
This patch fixes some incorrect type in assignment reported by sparse.
Those sparse warning as below:
- warning : restricted __le16 degrades to integer
- warning : cast from restricted __le32
- warning : expected restricted __le32
- warning : cast from restricted __be32
- warning : cast from restricted __be16
- warning : cast to restricted __le16
Signed-off-by: Guojia Liao <liaoguojia@huawei.com> Reviewed-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu [Wed, 28 Aug 2019 14:23:10 +0000 (22:23 +0800)]
net: hns3: make some reusable codes into a function
In hclge_dcb.c, these pair of codes:
hclge_notify_client(hdev, HNAE3_DOWN_CLIENT);
hclge_notify_client(hdev, HNAE3_UNINIT_CLIENT);
and
hclge_notify_client(hdev, HNAE3_INIT_CLIENT);
hclge_notify_client(hdev, HNAE3_UP_CLIENT);
are called many times, so make them into a function.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Reviewed-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Wed, 28 Aug 2019 14:23:09 +0000 (22:23 +0800)]
net: hns3: optimize some log printings
To better identify abnormal conditions, this patch modifies or
adds some logs to show driver status more accurately.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Guojia Liao [Wed, 28 Aug 2019 14:23:08 +0000 (22:23 +0800)]
net: hns3: reduce the parameters of some functions
This patch simplifies parameters of some functions by deleting
unused parameter.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com> Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Wed, 28 Aug 2019 14:23:07 +0000 (22:23 +0800)]
net: hns3: modify base parameter of kstrtouint in hclge_dbg_dump_tm_map
This patch replaces kstrtouint()'s patameter base with 0 in the
hclge_dbg_dump_tm_mac(), which makes it more flexible. Also
uses a macro to replace string "dump tm map", since it has been
used multiple times.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhongzhu Liu [Wed, 28 Aug 2019 14:23:05 +0000 (22:23 +0800)]
net: hns3: code optimization for debugfs related to "dump reg"
For making the code more readable, this patch uses a array to
keep the information about the dumping register, and then uses
it to parse the parameter cmd_buf which passing into
hclge_dbg_dump_reg_cmd().
Also replaces parameter "base" of kstrtouint with 0 in the
hclge_dbg_dump_reg_common(), which makes it more flexible.
Signed-off-by: Zhongzhu Liu <liuzhongzhu@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Radulescu [Wed, 28 Aug 2019 14:08:15 +0000 (17:08 +0300)]
dpaa2-eth: Add pause frame support
Starting with firmware version MC10.18.0, we have support for
L2 flow control. Asymmetrical configuration (Rx or Tx only) is
supported, but not pause frame autonegotioation.
Pause frame configuration is done via ethtool. By default, we start
with flow control enabled on both Rx and Tx. Changes are propagated
to hardware through firmware commands, using two flags (PAUSE,
ASYM_PAUSE) to specify Rx and Tx pause configuration, as follows:
The hardware can automatically send pause frames when the number
of buffers in the pool goes below a predefined threshold. Due to
this, flow control is incompatible with Rx frame queue taildrop
(both mechanisms target the case when processing of ingress
frames can't keep up with the Rx rate; for large frames, the number
of buffers in the pool may never get low enough to trigger pause
frames as long as taildrop is enabled). So we set pause frame
generation and Rx FQ taildrop as mutually exclusive.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Radulescu [Wed, 28 Aug 2019 14:08:14 +0000 (17:08 +0300)]
dpaa2-eth: Use stored link settings
Whenever a link state change occurs, we get notified and save
the new link settings in the device's private data. In ethtool
get_link_ksettings, use the stored state instead of interrogating
the firmware each time.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Radulescu [Wed, 28 Aug 2019 14:08:13 +0000 (17:08 +0300)]
dpaa2-eth: Remove support for changing link settings
We only support fixed-link for now, so there is no point in
offering users the option to change link settings via ethtool.
Functionally there is no change, since firmware prevents us from
changing link parameters anyway.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 29 Aug 2019 01:24:04 +0000 (18:24 -0700)]
Merge branch 'mlxsw-Various-updates'
Ido Schimmel says:
====================
mlxsw: Various updates
Patch #1 from Amit removes 56G speed support. The reasons for this are
detailed in the commit message.
Patch #2 from Shalom ensures that the hardware does not auto negotiate
the number of used lanes. For example, if a four lane port supports 100G
over both two and four lanes, it will not advertise the two lane link
mode.
Patch #3 bumps the firmware version supported by the driver.
Patch #4 from Petr adds ethtool counters to help debug the internal PTP
implementation in mlxsw. I copied Richard on this patch in case he has
comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Wed, 28 Aug 2019 15:54:37 +0000 (18:54 +0300)]
mlxsw: spectrum_ptp: Add counters for GC events
On Spectrum-1, timestamped PTP packets and the corresponding timestamps need to
be kept in caches until both are available, at which point they are matched up
and packets forwarded as appropriate. However, not all packets will ever see
their timestamp, and not all timestamps will ever see their packet. It is
necessary to dispose of such abandoned entries, so a garbage collector was
introduced in commit 45a0b3506df6 ("mlxsw: spectrum: PTP: Garbage-collect
unmatched entries").
If these GC events happen often, it is a sign of a problem. However because this
whole mechanism is taking place behind the scenes, there is no direct way to
determine whether garbage collection took place.
Therefore to fix this, on Spectrum-1 only, expose four artificial ethtool
counters for the GC events: GCd timestamps and packets, in TX and RX directions.
Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Wed, 28 Aug 2019 15:54:35 +0000 (18:54 +0300)]
mlxsw: spectrum: Prevent auto negotiation on number of lanes
After 50G-1-lane and 100G-2-lanes link modes were introduced, the driver
is facing situations in which the hardware auto negotiates not only on
speed and type, but also on number of lanes.
Prevent auto negotiation on number of lanes by allowing only port speeds
that can be supported on a given port according to its width.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Wed, 28 Aug 2019 15:54:34 +0000 (18:54 +0300)]
mlxsw: Remove 56G speed support
Commit bf56b3717151 ("mlxsw: spectrum: Prevent force of 56G") prevented
the driver from setting a speed of 56G when auto-negotiation is off.
This is the only speed supported by mlxsw that cannot be set when
auto-negotiation is off, which makes it difficult to write generic
tests.
Further, the speed is not supported by newer ASICs such as Spectrum-2
and to the best of our knowledge it is not used by current users.
Therefore, remove 56G support from mlxsw.
Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Wed, 28 Aug 2019 01:34:47 +0000 (09:34 +0800)]
net: phy: force phy suspend when calling phy_stop
Some ethernet drivers may call phy_start() and phy_stop() from
ndo_open() and ndo_close() respectively.
When network cable is unconnected, and operate like below:
step 1: ifconfig ethX up -> ndo_open -> phy_start ->start
autoneg, and phy is no link.
step 2: ifconfig ethX down -> ndo_close -> phy_stop -> just stop
phy state machine.
This patch forces phy suspend even phydev->link is off.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 28 Aug 2019 22:47:11 +0000 (15:47 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-08-26
This series contains updates to ice driver only.
Usha fixes the statistics reported on 4 port NICs which were reporting
the incorrect statistics due to using the incorrect port identifier.
Victor fixes an issue when trying to traverse to the first node of a
requested layer by adding a sibling head pointer for each layer per
traffic class.
Anirudh cleans up the locking and logic for enabling and disabling
VSI's to make it more consistent. Updates the driver to do dynamic
allocation of queue management bitmaps and arrays, rather than
statically allocating them which consumes more memory than required.
Refactor the logic in ice_ena_msix_range() for clarity and add
additional checks for when requested resources exceed what is available.
Jesse updates the debugging print statements to make it more useful when
dealing with link and PHY related issues.
Krzysztof adds a local variable to the VSI rebuild path to improve
readability.
Akeem limits the reporting of MDD events from VFs so that the kernel
log is not clogged up with MDD events which are duplicate or potentially
false positives. Fixed a reset issue that would result in the system
getting into a state that could only be resolved by a reboot by
testing if the VF is in a disabled state during a reset.
Michal adds a check to avoid trying to access memory that has not be
allocated by checking the number of queue pairs.
Jake fixes a static analysis warning due to a cast of a u8 to unsigned
long, so just update ice_is_tc_ena() to take a unsigned long so that a
cast is not necessary.
Colin Ian King fixes a potential infinite loop where a u8 is being
compared to an int.
Maciej refactors the queue handling functions that work on queue arrays
so that the logic can be done for a single queue.
Paul adds support for VFs to enable and disable single queues.
Henry fixed the order of operations in ice_remove() which was trying to
use adminq operations that were already disabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Tue, 27 Aug 2019 13:46:16 +0000 (21:46 +0800)]
phy: mdio-bcm-iproc: use devm_platform_ioremap_resource() to simplify code
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 27 Aug 2019 11:47:39 +0000 (12:47 +0100)]
wimax/i2400m: remove redundant assignment to variable result
Variable result is being assigned a value that is never read and result
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Ununsed value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Levin [Mon, 29 Apr 2019 14:45:52 +0000 (17:45 +0300)]
net/mlx5e: Support RSS for IP-in-IP and IPv6 tunneled packets
Add support for inner header RSS on IP-in-IP and IPv6 tunneled packets.
Add rules to the steering table regarding outer IP header, with
IPv4/6->IP-in-IP. Tunneled packets with protocol numbers: 0x4 (IP-in-IP)
and 0x29 (IPv6) are RSS-ed on the inner IP header.
Separate FW dependencies between flow table inner IP capabilities and
GRE offload support. Allowing this feature even if GRE offload is not
supported. Tested with multi stream TCP traffic tunneled with IPnIP.
Verified that:
Without this patch, only a single RX ring was processing the traffic.
With this patch, multiple RX rings were processing the traffic.
Verified with and without GRE offload support.
Aya Levin [Thu, 8 Aug 2019 13:16:28 +0000 (16:16 +0300)]
net/mlx5e: Change function's position to a more fitting file
Move function which indicates whether tunnel inner flow table is
supported from en.h to en_fs.c. It fits better right after tunnel
protocol rules definitions.
Moshe Shemesh [Sun, 4 Aug 2019 14:53:09 +0000 (17:53 +0300)]
net/mlx5e: Add device out of buffer counter
Added the following packets drop counter:
Device out of buffer - counts packets which were dropped due to full
device internal receive queue.
This counter will be shown on ethtool as a new counter called
dev_out_of_buffer.
The counter is read from FW by command QUERY_VNIC_ENV.
net/mlx5e: Support LAG TX port affinity distribution
When the VF LAG is in use, round-robin the TX affinity of channels among
the different ports, if supported by the firmware. Create a set of TISes
per port, while doing round-robin of the channels over the different
sets. Let all SQs of a channel share the same set of TISes.
If lag_tx_port_affinity HCA cap bit is supported, num_lag_ports > 1 and
we aren't the LACP owner (PF in the regular use), assign the affinities,
otherwise use tx_affinity == 0 in TIS context to let the FW assign the
affinities itself. The TISes of the LACP owner are mapped only to the
native physical port.
For VFs, the starting port for round-robin is determined by its vhca_id,
because a VF may have only one channel if attached to a single-core VM.
Erez Alfasi [Wed, 7 Aug 2019 14:56:02 +0000 (17:56 +0300)]
net/mlx5e: ethtool, Fix a typo in WOL function names
Fix a typo in 'mlx5e_refomrat_wol_mode_mlx5_to_linux' and
'mlx5e_refomrat_wol_mode_linux_to_mlx5' function names:
"refomrat" -> "reformat".
Fixes: 362adbbf49fd ("net/mlx5e: Wake On LAN support") Signed-off-by: Erez Alfasi <ereza@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Wed, 28 Aug 2019 18:45:03 +0000 (11:45 -0700)]
Merge branch 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 HW spec and bits updates:
1) Aya exposes IP-in-IP capability in mlx5_core.
2) Maxim exposes lag tx port affinity capabilities.
3) Moshe adds VNIC_ENV internal rq counter bits.
4) ODP capabilities for DC transport
Misc updates:
5) Saeed, two compiler warnings cleanups
6) Add XRQ legacy commands opcodes
7) Use refcount_t for refcount
8) fix a -Wstringop-truncation warning
====================
stmmac: Add EHL and TGL PCI info and PCI ID
In order to keep PCI info simple and neat, this patch series have
introduced a 3 hierarchy of struct. First layer will be the
intel_mgbe_common_data struct which keeps all Intel common configuration.
Second layer will be xxx_common_data which keeps all the different Intel
microarchitecture, e.g tgl, ehl. The third layer will be configuration
that tied to the PCI ID only based on speed and RGMII/SGMII interface.
EHL and TGL will also having a higher system clock which is 200Mhz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Voon Weifeng [Tue, 27 Aug 2019 01:38:11 +0000 (09:38 +0800)]
net: stmmac: setup higher frequency clk support for EHL & TGL
EHL DW EQOS is running on a 200MHz clock. Setting up stmmac-clk,
ptp clock and ptp_max_adj to 200MHz.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Voon Weifeng [Tue, 27 Aug 2019 01:38:10 +0000 (09:38 +0800)]
net: stmmac: add EHL RGMII 1Gbps PCI info and PCI ID
Added EHL RGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Voon Weifeng [Tue, 27 Aug 2019 01:38:09 +0000 (09:38 +0800)]
net: stmmac: add TGL SGMII 1Gbps PCI info and PCI ID
Added TGL SGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Voon Weifeng [Tue, 27 Aug 2019 01:38:08 +0000 (09:38 +0800)]
net: stmmac: add EHL SGMII 1Gbps PCI info and PCI ID
Added EHL SGMII 1Gbps PCI ID. Different MII and speed will have
different PCI ID.
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
this is the fifth version of changes for the Topaz/Peridot family of
switches. The patches apply on net-next.
Changes since v4:
- added Reviewed-by and Tested-by tags on first 2 patches, the others
are changed are affected by changes in patch 3/6, so I did not add
the tags, except for 5/6, which is just macro renaming
- patch 3 was changed: the serdes_get_lane returns 0 on success (lane
was discovered), -ENODEV if not lane is present on the port, and
other error if other error occured. Lane is put into a pointer of
type u8
- patches 4 and 6 were affected by this (error detecting from
serdes_get_lane)
- Andrew's complaint about the two additional parameters
(allow_over_2500 and make_cmode_writable) was addressed, by Vivien's
advice: I put a new method into chip operations structure, named
port_set_cmode_writable. This is called from mv88e6xxx_port_setup_mac
just before port_set_cmode. The method is implemented for Topaz.
The check if cmodes over 2500 should be allowed on given port is now
done in the specific port_set_cmode() that requires it, thus the
allow_over_2500 argument is not needed
Again, tested on Turris Mox with Peridot, Topaz, and Peridot + Topaz.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Mon, 26 Aug 2019 21:31:55 +0000 (23:31 +0200)]
net: dsa: mv88e6xxx: fully support SERDES on Topaz family
Currently we support SERDES on the Topaz family in a limited way: no
IRQs and the cmode is not writable, thus the mode is determined by
strapping pins.
Marvell's examples though show how to make cmode writable on port 5 and
support SGMII autonegotiation. It is done by writing hidden registers,
for which we already have code.
This patch adds support for making the cmode for the SERDES port
writable on the Topaz family, via a new chip operation,
.port_set_cmode_writable, which is called from mv88e6xxx_port_setup_mac
just before .port_set_cmode.
SERDES IRQs are also enabled for Topaz.
Tested on Turris Mox.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Mon, 26 Aug 2019 21:31:54 +0000 (23:31 +0200)]
net: dsa: mv88e6xxx: rename port cmode macro
This is a cosmetic update. We are removing the last underscore from
macros MV88E6XXX_PORT_STS_CMODE_100BASE_X and
MV88E6XXX_PORT_STS_CMODE_1000BASE_X. The 2500base-x version does not
have that underscore. Also PHY_INTERFACE_MODE_ macros do not have it
there.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Mon, 26 Aug 2019 21:31:53 +0000 (23:31 +0200)]
net: dsa: mv88e6xxx: simplify SERDES code for Topaz and Peridot
By adding an additional serdes_get_lane implementation (for Topaz), we
can merge the implementations of other SERDES functions (powering and
IRQs). We can skip checking port numbers, since the serdes_get_lane()
methods inform if there is no lane on a port or if the lane cannot be
used for given cmode.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Create a serdes_get_lane() method in the mv88e6xxx operations structure.
Use it instead of calling the different implementations.
Also change the methods so that their return value is used only for
error. The lane number is put into a place referred to by a pointer
given as argument. If the port does not have a lane, return -ENODEV.
Lanes are phy addresses, so use u8 as their type.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Mon, 26 Aug 2019 21:31:51 +0000 (23:31 +0200)]
net: dsa: mv88e6xxx: update code operating on hidden registers
This patch moves the functions operating on the hidden debug registers
into it's own file, port_hidden.c. The functions prefix is renamed from
mv88e6390_hidden_ to mv88e6xxx_port_hidden_, to be consistent with the
rest of this driver. The macros are prefixed with MV88E6XXX_ prefix, and
are changed not to use the BIT() macro nor bit shifts, since the rest of
the port.h file does not use it.
We also add the support for setting the Block Address field when
operating hidden registers. Marvell's mdio examples for SERDES settings
on Topaz use Block Address 0x7 when reading/writing hidden registers,
and although the specification says that block must be set to 0xf, those
settings are reachable only with Block Address 0x7.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Behún [Mon, 26 Aug 2019 21:31:50 +0000 (23:31 +0200)]
net: dsa: mv88e6xxx: support 2500base-x in SGMII IRQ handler
The mv88e6390_serdes_irq_link_sgmii IRQ handler reads the SERDES PHY
status register to determine speed, among other things. If cmode of the
port is set to 2500base-x, though, the PHY still reports 1000 Mbps (the
PHY register itself does not differentiate between 1000 Mbps and 2500
Mbps - it thinks it is running at 1000 Mbps, although clock is 2.5x
faster).
Look at the cmode and set SPEED_2500 if cmode is set to 2500base-x.
Also tell mv88e6xxx_port_setup_mac the PHY interface mode corresponding
to current cmode in terms of phy_interface_t.
Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset is to make ecn flag per netns and endpoint and then
add SCTP_ECN_SUPPORTED sockopt, as does for other feature flags.
====================
Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Mon, 26 Aug 2019 08:30:02 +0000 (16:30 +0800)]
sctp: make ecn flag per netns and endpoint
This patch is to add ecn flag for both netns_sctp and sctp_endpoint,
net->sctp.ecn_enable is set 1 by default, and ep->ecn_enable will
be initialized with net->sctp.ecn_enable.
asoc->peer.ecn_capable will be set during negotiation only when
ep->ecn_enable is set on both sides.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Mon, 26 Aug 2019 01:31:18 +0000 (09:31 +0800)]
net: mediatek: remove set but not used variable 'status'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/mediatek/mtk_eth_soc.c: In function mtk_handle_irq:
drivers/net/ethernet/mediatek/mtk_eth_soc.c:1951:6: warning: variable status set but not used [-Wunused-but-set-variable]
Fixes: 7e1c560ef531 ("net: ethernet: mediatek: Add MT7628/88 SoC support") Signed-off-by: Mao Wenan <maowenan@huawei.com> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Simplify DSA handling of VLAN subinterface offload
Depends on Vivien Didelot's patchset:
https://patchwork.ozlabs.org/project/netdev/list/?series=127197&state=*
This patchset removes a few strange-looking guards for -EOPNOTSUPP in
dsa_slave_vlan_rx_add_vid and dsa_slave_vlan_rx_kill_vid, making that
code path no longer possible.
It also disables the code path for the sja1105 driver, which does
support editing the VLAN table, but not hardware-accelerated VLAN
sub-interfaces, therefore the check in the DSA core would be wrong.
There was no better DSA callback to do this than .port_enable, i.e.
at ndo_open time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch barely supports traffic I/O, and it does that by repurposing
VLANs when there is no bridge that is taking control of them.
Letting DSA declare this netdev feature as supported (see
dsa_slave_create) would mean that VLAN sub-interfaces created on sja1105
switch ports will be hardware offloaded. That means that
net/8021q/vlan_core.c would install the VLAN into the filter tables of
the switch, potentially interfering with the tag_8021q VLANs.
We need to prevent that from happening and not let the 8021q core
offload VLANs to the switch hardware tables. In vlan_filtering=0 modes
of operation, the switch ports can pass through VLAN-tagged frames with
no problem.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sun, 25 Aug 2019 19:46:29 +0000 (22:46 +0300)]
net: dsa: Advertise the VLAN offload netdev ability only if switch supports it
When adding a VLAN sub-interface on a DSA slave port, the 8021q core
checks NETIF_F_HW_VLAN_CTAG_FILTER and, if the netdev is capable of
filtering, calls .ndo_vlan_rx_add_vid or .ndo_vlan_rx_kill_vid to
configure the VLAN offloading.
DSA sets this up counter-intuitively: it always advertises this netdev
feature, but the underlying driver may not actually support VLAN table
manipulation. In that case, the DSA core is forced to ignore the error,
because not being able to offload the VLAN is still fine - and should
result in the creation of a non-accelerated VLAN sub-interface.
Change this so that the netdev feature is only advertised for switch
drivers that support VLAN manipulation, instead of checking for
-EOPNOTSUPP at runtime.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: ethernet: mediatek: convert to PHYLINK
These patches converts mediatek driver to PHYLINK API.
v3->v4:
* Phylink improvements and clean-ups after review
v2->v3:
* Phylink improvements and clean-ups after review
v1->v2:
* Rebase for mt76x8 changes
* Phylink improvements and clean-ups after review
* SGMII port doesn't support 2.5Gbit in SGMII mode only in BASE-X mode.
Refactor the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
René van Dorst [Sun, 25 Aug 2019 17:43:41 +0000 (19:43 +0200)]
dt-bindings: net: ethernet: Update mt7622 docs and dts to reflect the new phylink API
This patch the removes the recently added mediatek,physpeed property.
Use the fixed-link property speed = <2500> to set the phy in 2.5Gbit.
See mt7622-bananapi-bpi-r64.dts for a working example.
Signed-off-by: René van Dorst <opensource@vdorst.com> Signed-off-by: David S. Miller <davem@davemloft.net>
René van Dorst [Sun, 25 Aug 2019 17:43:40 +0000 (19:43 +0200)]
net: ethernet: mediatek: Re-add support SGMII
* Re-add SGMII support but now with PHYLINK API support
So the SGMII changes are more clear
* Move SGMII block setup from mtk_gmac_sgmii_path_setup() to
mtk_mac_config()
* Merge mtk_setup_hw_path() into mtk_mac_config()
* Remove mediatek,physpeed property, fixed-link supports now any speed so
speed = <2500>; is now valid with PHYLINK
* Demagic SGMII register values
* Use phylink state to setup fixed-link mode
Signed-off-by: René van Dorst <opensource@vdorst.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: dsa: explicit programmation of VLAN on CPU ports
When a VLAN is programmed on a user port, every switch of the fabric also
program the CPU ports and the DSA links as part of the VLAN. To do that,
DSA makes use of bitmaps to prepare all members of a VLAN.
While this is expected for DSA links which are used as conduit between
interconnected switches, only the dedicated CPU port of the slave must be
programmed, not all CPU ports of the fabric. This may also cause problems in
other corners of DSA such as the tag_8021q.c driver, which needs to program
its ports manually, CPU port included.
We need the dsa_port_vlan_{add,del} functions and its dsa_port_vid_{add,del}
variants to simply trigger the VLAN programmation without any logic in them,
but they may currently skip the operation based on the bridge device state.
This patchset gets rid of the bitmap operations, and moves the bridge device
check as well as the explicit programmation of CPU ports where they belong,
in the slave code.
While at it, clear the VLAN flags before programming a CPU port, as it
doesn't make sense to forward the PVID flag for example for such ports.
Changes in v2: only clear the PVID flag.
====================
Tested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sun, 25 Aug 2019 17:25:20 +0000 (13:25 -0400)]
net: dsa: clear VLAN PVID flag for CPU port
When the bridge offloads a VLAN on a slave port, we also need to
program its dedicated CPU port as a member of the VLAN.
Drivers may handle the CPU port's membership as they want. For example,
Marvell as a special "Unmodified" mode to pass frames as is through
such ports.
Even though DSA expects the drivers to handle the CPU port membership,
it does not make sense to program user VLANs as PVID on the CPU port.
This patch clears this flag before programming the CPU port.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Suggested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sun, 25 Aug 2019 17:25:19 +0000 (13:25 -0400)]
net: dsa: program VLAN on CPU port from slave
DSA currently programs a VLAN on the CPU port implicitly after the
related notifier is received by a switch.
While we still need to do this transparent programmation of the DSA
links in the fabric, programming the CPU port this way may cause
problems in some corners such as the tag_8021q driver.
Because the dedicated CPU port is specific to a slave, make their
programmation explicit a few layers up, in the slave code.
Note that technically, DSA links have a dedicated CPU port as well,
but since they are only used as conduit between interconnected switches
of a fabric, programming them transparently this way is what we want.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sun, 25 Aug 2019 17:25:18 +0000 (13:25 -0400)]
net: dsa: check bridge VLAN in slave operations
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Suggested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sun, 25 Aug 2019 17:25:17 +0000 (13:25 -0400)]
net: dsa: add slave VLAN helpers
Add dsa_slave_vlan_add and dsa_slave_vlan_del helpers to handle
SWITCHDEV_OBJ_ID_PORT_VLAN switchdev objects. Also copy the
switchdev_obj_port_vlan structure on add since we will modify it in
future patches.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sun, 25 Aug 2019 17:25:16 +0000 (13:25 -0400)]
net: dsa: do not skip -EOPNOTSUPP in dsa_port_vid_add
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sun, 25 Aug 2019 17:25:15 +0000 (13:25 -0400)]
net: dsa: remove bitmap operations
The bitmap operations were introduced to simplify the switch drivers
in the future, since most of them could implement the common VLAN and
MDB operations (add, del, dump) with simple functions taking all target
ports at once, and thus limiting the number of hardware accesses.
Programming an MDB or VLAN this way in a single operation would clearly
simplify the drivers a lot but would require a new get-set interface
in DSA. The usage of such bitmap from the stack also raised concerned
in the past, leading to the dynamic allocation of a new ds->_bitmap
member in the dsa_switch structure. So let's get rid of them for now.
This commit nicely wraps the ds->ops->port_{mdb,vlan}_{prepare,add}
switch operations into new dsa_switch_{mdb,vlan}_{prepare,add}
variants not using any bitmap argument anymore.
New dsa_switch_{mdb,vlan}_match helpers have been introduced to make
clear which local port of a switch must be programmed with the target
object. While the targeted user port is an obvious candidate, the
DSA links must also be programmed, as well as the CPU port for VLANs.
While at it, also remove local variables that are only used once.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Qian Cai [Fri, 23 Aug 2019 19:56:23 +0000 (15:56 -0400)]
net/mlx5: fix a -Wstringop-truncation warning
In file included from ./arch/powerpc/include/asm/paca.h:15,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./include/asm-generic/preempt.h:5,
from ./arch/powerpc/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:51,
from ./include/linux/wait.h:9,
from ./include/linux/completion.h:12,
from ./include/linux/mlx5/driver.h:37,
from
drivers/net/ethernet/mellanox/mlx5/core/lib/eq.h:6,
from
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:33:
In function 'strncpy',
inlined from 'mlx5_fw_tracer_save_trace' at
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:549:2,
inlined from 'mlx5_tracer_print_trace' at
drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:574:2:
./include/linux/string.h:305:9: warning: '__builtin_strncpy' output may
be truncated copying 256 bytes from a string of length 511
[-Wstringop-truncation]
return __builtin_strncpy(p, q, size);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix it by using the new strscpy_pad() since the commit fa23ee028e48
("lib/string: Add strscpy_pad() function") which will always
NUL-terminate the string, and avoid possibly leak data through the ring
buffer where non-admin account might enable these events through perf.
Fixes: ed7e10d65e90 ("net/mlx5: Add support for FW reporter dump") Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
* tag 'nfs-for-5.3-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: remove set but not used variable 'mapping'
NFSv2: Fix write regression
NFSv2: Fix eof handling
NFS: Fix writepage(s) error handling to not report errors twice
NFS: Fix spurious EIO read errors
pNFS/flexfiles: Don't time out requests on hard mounts
SUNRPC: Handle connection breakages correctly in call_status()
Revert "NFSv4/flexfiles: Abort I/O early if the layout segment was invalidated"
SUNRPC: Handle EADDRINUSE and ENOBUFS correctly
pNFS/flexfiles: Turn off soft RPC calls
SUNRPC: Don't handle errors if the bind/connect succeeded
NFS: On fatal writeback errors, we need to call nfs_inode_remove_request()
NFS: Fix initialisation of I/O result struct in nfs_pgio_rpcsetup
NFS: Ensure O_DIRECT reports an error if the bytes read/written is 0
NFSv4/pnfs: Fix a page lock leak in nfs_pageio_resend()
NFSv4: Fix return value in nfs_finish_open()
NFSv4: Fix return values for nfs4_file_open()
NFS: Don't refresh attributes with mounted-on-file information
Linus Torvalds [Tue, 27 Aug 2019 17:50:27 +0000 (10:50 -0700)]
Merge tag 'arc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- support for Edge Triggered IRQs in ARC IDU intc
- other fixes here and there
* tag 'arc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: prefer __section from compiler_attributes.h
dt-bindings: IDU-intc: Add support for edge-triggered interrupts
dt-bindings: IDU-intc: Clean up documentation
ARCv2: IDU-intc: Add support for edge-triggered interrupts
ARC: unwind: Mark expected switch fall-throughs
ARC: [plat-hsdk]: allow to switch between AXI DMAC port configurations
ARC: fix typo in setup_dma_ops log message
ARCv2: entry: early return from exception need not clear U & DE bits
Linus Torvalds [Tue, 27 Aug 2019 17:47:01 +0000 (10:47 -0700)]
Merge tag 'mfd-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fix from Lee Jones:
"Identify potentially unused functions in rk808 driver when !PM"
* tag 'mfd-fixes-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: rk808: Make PM function declaration static
mfd: rk808: Mark pm functions __maybe_unused
1) Use 32-bit index for tails calls in s390 bpf JIT, from Ilya
Leoshkevich.
2) Fix missed EPOLLOUT events in TCP, from Eric Dumazet. Same fix for
SMC from Jason Baron.
3) ipv6_mc_may_pull() should return 0 for malformed packets, not
-EINVAL. From Stefano Brivio.
4) Don't forget to unpin umem xdp pages in error path of
xdp_umem_reg(). From Ivan Khoronzhuk.
5) Fix sta object leak in mac80211, from Johannes Berg.
6) Fix regression by not configuring PHYLINK on CPU port of bcm_sf2
switches. From Florian Fainelli.
7) Revert DMA sync removal from r8169 which was causing regressions on
some MIPS Loongson platforms. From Heiner Kallweit.
8) Use after free in flow dissector, from Jakub Sitnicki.
9) Fix NULL derefs of net devices during ICMP processing across
collect_md tunnels, from Hangbin Liu.
10) proto_register() memory leaks, from Zhang Lin.
11) Set NLM_F_MULTI flag in multipart netlink messages consistently,
from John Fastabend.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
r8152: Set memory to all 0xFFs on failed reg reads
openvswitch: Fix conntrack cache with timeout
ipv4: mpls: fix mpls_xmit for iptunnel
nexthop: Fix nexthop_num_path for blackhole nexthops
net: rds: add service level support in rds-info
net: route dump netlink NLM_F_MULTI flag missing
s390/qeth: reject oversized SNMP requests
sock: fix potential memory leak in proto_register()
MAINTAINERS: Add phylink keyword to SFF/SFP/SFP+ MODULE SUPPORT
xfrm/xfrm_policy: fix dst dev null pointer dereference in collect_md mode
ipv4/icmp: fix rt dst dev null pointer dereference
openvswitch: Fix log message in ovs conntrack
bpf: allow narrow loads of some sk_reuseport_md fields with offset > 0
bpf: fix use after free in prog symbol exposure
bpf: fix precision tracking in presence of bpf2bpf calls
flow_dissector: Fix potential use-after-free on BPF_PROG_DETACH
Revert "r8169: remove not needed call to dma_sync_single_for_device"
ipv6: propagate ipv6_add_dev's error returns out of ipv6_find_idev
net/ncsi: Fix the payload copying for the request coming from Netlink
qed: Add cleanup in qed_slowpath_start()
...
Henry Tieman [Fri, 2 Aug 2019 08:25:24 +0000 (01:25 -0700)]
ice: fix adminq calls during remove
The order of operations was incorrect in ice_remove(). The code would
try to use adminq operations after the adminq was disabled. This caused
all adminq calls to fail and possibly timeout waiting.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The current implementation of ice_ena_msix_range is difficult to read
and has subtle issues. This patch reworks the said function for
clarity and correctness.
More specifically,
1. Add more checks to bail out of 'needed' is greater than 'v_left'.
2. Simplify fallback logic
3. Do not set pf->num_avail_sw_msix in ice_ena_msix_range as it
gets overwritten by ice_init_interrupt_scheme.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a critical reset issue that resulting to the server
reboot when an Admin changes VF configuration on the host, for example
changing VF to Trusted/non_Trusted mode, the PF driver send reset
notification to AVF driver while also continue with reset flow. However,
AVF driver schedule another reset due to notification, which causes two
concurrent reset going on, and trigger lock up in the FW, with AQ call to
delete VSI.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice: Alloc queue management bitmaps and arrays dynamically
The total number of queues available on the device is divided between
multiple physical functions (PF) in the firmware and provided to the
driver when it gets function capabilities from the firmware. Thus
each PF knows how many Tx/Rx queues it has. These queues are then
doled out to different VSIs (for LAN traffic, SR-IOV VF traffic, etc.)
To track usage of these queues at the PF level, the driver uses two
bitmaps avail_txqs and avail_rxqs. At the VSI level (i.e. struct ice_vsi
instances) the driver uses two arrays txq_map and rxq_map, to track
ownership of VSIs' queues in avail_txqs and avail_rxqs respectively.
The aforementioned bitmaps and arrays should be allocated dynamically,
because the number of queues supported by a PF is only available once
function capabilities have been queried. The current static allocation
consumes way more memory than required.
This patch removes the DECLARE_BITMAP for avail_txqs and avail_rxqs
and instead uses bitmap_zalloc to allocate the bitmaps during init.
Similarly txq_map and rxq_map are now allocated in ice_vsi_alloc_arrays.
As a result ICE_MAX_TXQS and ICE_MAX_RXQS defines are no longer needed.
Also as txq_map and rxq_map are now allocated and freed, some code
reordering was required in ice_vsi_rebuild for correct functioning.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
projects / kernel.git / log