Sergei Shtylyov [Sat, 15 Feb 2020 20:13:45 +0000 (23:13 +0300)]
sh_eth: add sh_eth_cpu_data::gecmr flag
Not all Ether controllers having the Gigabit register layout have GECMR --
RZ/A1 (AKA R7S72100) actually has the same layout but no Gigabit speed
support and hence no GECMR. In the past, the new register map table was
added for this SoC, now I think we should have used the existing Gigabit
table with the differences (such as GECMR) covered by the mere flags in
the 'struct sh_eth_cpu_data'. Add such flag for GECMR -- and then we can
get rid of the R7S72100 specific layout in the next patch...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 15 Feb 2020 20:10:53 +0000 (23:10 +0300)]
sh_eth: check sh_eth_cpu_data::no_xdfar when dumping registers
When adding the sh_eth_cpu_data::no_xdfar flag I forgot to add the flag
check to __sh_eth_get_regs(), causing the non-existing RDFAR/TDFAR to be
considered for dumping on the R-Car gen1/2 SoCs (the register offset check
has the final say here)...
Fixes: fb394fe3b99 ("sh_eth: add sh_eth_cpu_data::cexcr flag") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 15 Feb 2020 20:09:35 +0000 (23:09 +0300)]
sh_eth: check sh_eth_cpu_data::cexcr when dumping registers
When adding the sh_eth_cpu_data::cexcr flag I forgot to add the flag
check to __sh_eth_get_regs(), causing the non-existing RX packet counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...
Fixes: fb394fe3b99 ("sh_eth: add sh_eth_cpu_data::cexcr flag") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Sat, 15 Feb 2020 20:08:20 +0000 (23:08 +0300)]
sh_eth: check sh_eth_cpu_data::no_tx_cntrs when dumping registers
When adding the sh_eth_cpu_data::no_tx_cntrs flag I forgot to add the
flag check to __sh_eth_get_regs(), causing the non-existing TX counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...
Fixes: c38d425a376d ("sh_eth: add sh_eth_cpu_data::no_tx_cntrs flag") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Tested-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Pause updates for phylib and phylink
Currently, phylib resolves the speed and duplex settings, which MAC
drivers use directly. phylib also extracts the "Pause" and "AsymPause"
bits from the link partner's advertisement, and stores them in struct
phy_device's pause and asym_pause members with no further processing.
It is left up to each MAC driver to implement decoding for this
information.
phylink converted drivers are able to take advantage of code therein
which resolves the pause advertisements for the MAC driver, but this
does nothing for unconverted drivers. It also does not allow us to
make use of hardware-resolved pause states offered by several PHYs.
This series aims to address this by:
1. Providing a generic implementation, linkmode_resolve_pause(), that
takes the ethtool linkmode arrays for the link partner and local
advertisements, decoding the result to whether pause frames should
be allowed to be transmitted or received and acted upon. I call
this the pause enablement state.
2. Providing a phylib implementation, phy_get_pause(), which allows
MAC drivers to request the pause enablement state from phylib.
3. Providing a generic linkmode_set_pause() for setting the pause
advertisement according to the ethtool tx/rx flags - note that this
design has some shortcomings, see the comments in the kerneldoc for
this function.
4. Remove the ability in phylink to set the pause states for fixed
links, which brings them into line with how we deal with the speed
and duplex parameters; we can reintroduce this later if anyone
requires it. This could be a userspace-visible change.
5. Split application of manual pause enablement state from phylink's
resolution of the same to allow use of phylib's new phy_get_pause()
interface by phylink, and make that switch.
6. Resolve the fixed-link pause enablement state using the generic
linkmode_resolve_pause() helper introduced earlier. This, in
connection with the previous commits, allows us to kill the
MLO_PAUSE_SYM and MLO_PAUSE_ASYM flags.
7. make phylink's ethtool pause setting implementation update the
pause advertisement in the same way that phylib does, with the
same caveats that are present there (as mentioned above w.r.t
linkmode_set_pause()).
8. create a more accurate initial configuration for MACs, used when
phy_start() is called or a SFP is detected. In particular, this
ensures that the pause bits seen by MAC drivers in state->pause
are accurate for SGMII.
9. finally, update the kerneldoc descriptions for mac_config() for
the above changes.
This series has been build-tested against net-next; the boot tested
patches are in my "phy" branch against v5.5 plus the queued phylink
changes that were merged for 5.6.
The next series will introduce the ability for phylib drivers to
provide hardware resolved pause enablement state. These patches can
be found in my "phy" branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:50:09 +0000 (15:50 +0000)]
net: phylink: clarify flow control settings in documentation
Clarify the expected flow control settings operation in the phylink
documentation for each negotiation mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:50:03 +0000 (15:50 +0000)]
net: phylink: improve initial mac configuration
Improve the initial MAC configuration so we get a configuration which
more represents the final operating mode, in particular with respect
to the flow control settings.
We do this by:
1) more fully initialising our phy state, so we can use this as the
initial state for PHY based connections.
2) reading the fixed link state.
3) ensuring that in-band mode has sane pause settings for SGMII vs
802.3z negotiation modes.
In all three cases, we ensure that state->link is false, just in case
any MAC drivers have other ideas by mis-using this member, and we also
take account of manual pause mode configuration at this point.
This avoids MLO_PAUSE_AN being seen in mac_config() when operating in
PHY, fixed mode or inband SGMII mode, thereby giving cleaner semantics
to the pause flags. As a result of this, the pause flags now indicate
in a mode-independent way what is required from a mac_config()
implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:49:58 +0000 (15:49 +0000)]
net: phylink: allow ethtool -A to change flow control advertisement
When ethtool -A is used to change the pause modes, the pause
advertisement is not being changed, but the documentation in
uapi/linux/ethtool.h says we should be. Add that capability to
phylink.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:49:53 +0000 (15:49 +0000)]
net: phylink: resolve fixed link flow control
Resolve the fixed link flow control using the recently introduced
linkmode_resolve_pause() helper, which we use in
phylink_get_fixed_state() only when operating in full duplex mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:49:48 +0000 (15:49 +0000)]
net: phylink: use phylib resolved flow control modes
Use the new phy_get_pause() helper to get the resolved pause modes for
a PHY rather than resolving the pause modes ourselves. We temporarily
retain our pause mode resolution for causes where there is no PHY
attached, e.g. for fixed-link modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:49:43 +0000 (15:49 +0000)]
net: phylink: ensure manual flow control is selected appropriately
Split the application of manually controlled flow control modes from
phylink_resolve_flow(), so that we can use alternative providers of
flow control resolution.
We also want to clear the MLO_PAUSE_AN flag when autoneg is disabled,
since flow control can't be negotiated in this circumstance.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:49:37 +0000 (15:49 +0000)]
net: phylink: remove pause mode ethtool setting for fixed links
Remove the ability for ethtool -A to change the pause settings for
fixed links; if this is really required, we can reinstate it later.
Andrew Lunn agrees: "So I think it is safe to not implement ethtool
-A, at least until somebody has a real use case for it."
Lets avoid making things too complex for use cases that aren't being
used.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:49:32 +0000 (15:49 +0000)]
net: add linkmode helper for setting flow control advertisement
Add a linkmode helper to set the flow control advertisement in an
ethtool linkmode mask according to the tx/rx capabilities. This
implementation is moved from phylib, and documented with an
analysis of its shortcomings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 15:49:27 +0000 (15:49 +0000)]
net: add helpers to resolve negotiated flow control
Add a couple of helpers to resolve negotiated flow control. Two helpers
are provided:
- linkmode_resolve_pause() which takes the link partner and local
advertisements, and decodes whether we should enable TX or RX pause
at the MAC. This is useful outside of phylib, e.g. in phylink.
- phy_get_pause(), which returns the TX/RX enablement status for the
current negotiation results of the PHY.
This allows us to centralise the flow control resolution, rather than
spreading it around.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Sat, 15 Feb 2020 23:57:36 +0000 (23:57 +0000)]
net: linkmode: make linkmode_test_bit() take const pointer
linkmode_test_bit() does not modify the address; test_bit() is also
declared const volatile for the same reason. There's no need for
linkmode_test_bit() to be any different, and allows implementation of
helpers that take a const linkmode pointer.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sat, 15 Feb 2020 13:54:14 +0000 (14:54 +0100)]
r8169: improve statistics of missed rx packets
Register RxMissed exists on few early chip versions only, however all
chip versions have the number of missed RX packets in the hardware
counters. Therefore remove using RxMissed and get the number of missed
RX packets from the hardware stats.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sat, 15 Feb 2020 13:52:05 +0000 (14:52 +0100)]
r8169: improve rtl8169_get_mac_version
Currently code snippet (RTL_R32(tp, TxConfig) >> 20) & 0xfcf is used
in few places to extract the chip XID. Change the code to do the XID
extraction only once.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sat, 15 Feb 2020 13:50:29 +0000 (14:50 +0100)]
r8169: add helper rtl_pci_commit
In few places we do a PCI commit by reading an arbitrary chip register.
It's not always obvious that the read is meant to be a PCI commit,
therefore add a helper for it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Sat, 15 Feb 2020 13:48:03 +0000 (14:48 +0100)]
r8169: remove unneeded check from rtl_link_chg_patch
rtl_link_chg_patch() can be called from rtl_open() to rtl8169_close()
only. And in rtl8169_close() phy_stop() ensures that this function
isn't called afterwards. So we don't need this check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Sat, 15 Feb 2020 13:20:56 +0000 (14:20 +0100)]
openvswitch: add TTL decrement action
New action to decrement TTL instead of setting it to a fixed value.
This action will decrement the TTL and, in case of expired TTL, drop it
or execute an action passed via a nested attribute.
The default TTL expired action is to drop the packet.
Supports both IPv4 and IPv6 via the ttl and hop_limit fields, respectively.
Tested with a corresponding change in the userspace:
Arjun Roy [Fri, 14 Feb 2020 23:30:50 +0000 (15:30 -0800)]
tcp-zerocopy: Return sk_err (if set) along with tcp receive zerocopy.
This patchset is intended to reduce the number of extra system calls
imposed by TCP receive zerocopy. For ping-pong RPC style workloads,
this patchset has demonstrated a system call reduction of about 30%
when coupled with userspace changes.
For applications using epoll, returning sk_err along with the result
of tcp receive zerocopy could remove the need to call
recvmsg()=-EAGAIN after a spurious wakeup.
Consider a multi-threaded application using epoll. A thread may awaken
with EPOLLIN but another thread may already be reading. The
spuriously-awoken thread does not necessarily know that another thread
'won'; rather, it may be possible that it was woken up due to the
presence of an error if there is no data. A zerocopy read receiving 0
bytes thus would need to be followed up by recvmsg to be sure.
Instead, we return sk_err directly with zerocopy, so the application
can avoid this extra system call.
Signed-off-by: Arjun Roy <arjunroy@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun Roy [Fri, 14 Feb 2020 23:30:49 +0000 (15:30 -0800)]
tcp-zerocopy: Return inq along with tcp receive zerocopy.
This patchset is intended to reduce the number of extra system calls
imposed by TCP receive zerocopy. For ping-pong RPC style workloads,
this patchset has demonstrated a system call reduction of about 30%
when coupled with userspace changes.
For applications using edge-triggered epoll, returning inq along with
the result of tcp receive zerocopy could remove the need to call
recvmsg()=-EAGAIN after a successful zerocopy. Generally speaking,
since normally we would need to perform a recvmsg() call for every
successful small RPC read via TCP receive zerocopy, returning inq can
reduce the number of system calls performed by approximately half.
Signed-off-by: Arjun Roy <arjunroy@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series improves the semantics behind the way virtio-vsock server
accepts connections coming from the client. Whenever the server
receives a connection request from the client, if it is bound to the
socket but not yet listening, it will answer with a RST packet. The
point is to ensure each request from the client is quickly processed
so that the client can decide about the strategy of retrying or not.
The series includes along with the improvement patch a new test to
ensure the behavior is consistent across all hypervisors drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastien Boeuf [Fri, 14 Feb 2020 11:48:02 +0000 (12:48 +0100)]
tools: testing: vsock: Test when server is bound but not listening
Whenever the server side of vsock is binding to the socket, but not
listening yet, we expect the behavior from the client to be identical to
what happens when the server is not even started.
This new test runs the server side so that it binds to the socket
without ever listening to it. The client side will try to connect and
should receive an ECONNRESET error.
This new test provides a way to validate the previously introduced patch
for making sure the server side will always answer with a RST packet in
case the client requested a new connection.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastien Boeuf [Fri, 14 Feb 2020 11:48:01 +0000 (12:48 +0100)]
net: virtio_vsock: Enhance connection semantics
Whenever the vsock backend on the host sends a packet through the RX
queue, it expects an answer on the TX queue. Unfortunately, there is one
case where the host side will hang waiting for the answer and might
effectively never recover if no timeout mechanism was implemented.
This issue happens when the guest side starts binding to the socket,
which insert a new bound socket into the list of already bound sockets.
At this time, we expect the guest to also start listening, which will
trigger the sk_state to move from TCP_CLOSE to TCP_LISTEN. The problem
occurs if the host side queued a RX packet and triggered an interrupt
right between the end of the binding process and the beginning of the
listening process. In this specific case, the function processing the
packet virtio_transport_recv_pkt() will find a bound socket, which means
it will hit the switch statement checking for the sk_state, but the
state won't be changed into TCP_LISTEN yet, which leads the code to pick
the default statement. This default statement will only free the buffer,
while it should also respond to the host side, by sending a packet on
its TX queue.
In order to simply fix this unfortunate chain of events, it is important
that in case the default statement is entered, and because at this stage
we know the host side is waiting for an answer, we must send back a
packet containing the operation VIRTIO_VSOCK_OP_RST.
One could say that a proper timeout mechanism on the host side will be
enough to avoid the backend to hang. But the point of this patch is to
ensure the normal use case will be provided with proper responsiveness
when it comes to establishing the connection.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 17 Feb 2020 03:00:22 +0000 (19:00 -0800)]
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
lib: objagg: Replace zero-length arrays with flexible-array member
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yangbo Lu [Tue, 11 Feb 2020 04:52:49 +0000 (12:52 +0800)]
ptp_qoriq: drop the code of alarm
The alarm function hadn't been supported by PTP clock driver.
The recommended solution PHC + phc2sys + nanosleep provides
best performance. So drop the code of alarm in ptp_qoriq driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Fix interrupt name truncation in mv88e6xxx dsa driver, from Andrew
Lunn.
2) Process generic XDP even if SKB is cloned, from Toke Høiland-Jørgensen.
3) Fix leak of kernel memory to userspace in smc, from Eric Dumazet.
4) Add some missing netlink attribute validation to matchall and
flower, from Davide Caratti.
5) Send icmp responses properly when NAT has been applied to the frame
before we get to the tunnel emitting the icmp, from Jason Donenfeld.
6) Make sure there is enough SKB headroom when adding dsa tags for qca
and ar9331. From Per Forlin.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits)
netdevice.h: fix all kernel-doc and Sphinx warnings
net: dsa: tag_ar9331: Make sure there is headroom for tag
net: dsa: tag_qca: Make sure there is headroom for tag
net, ip6_tunnel: enhance tunnel locate with link check
net/smc: no peer ID in CLC decline for SMCD
net/smc: transfer fasync_list in case of fallback
net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()
net: hns3: fix VF bandwidth does not take effect in some case
net: hns3: add management table after IMP reset
mac80211: fix wrong 160/80+80 MHz setting
cfg80211: add missing policy for NL80211_ATTR_STATUS_CODE
xfrm: interface: use icmp_ndo_send helper
wireguard: device: use icmp_ndo_send helper
sunvnet: use icmp_ndo_send helper
gtp: use icmp_ndo_send helper
icmp: introduce helper for nat'd source address in network device context
net/sched: flower: add missing validation of TCA_FLOWER_FLAGS
net/sched: matchall: add missing validation of TCA_MATCHALL_FLAGS
net/flow_dissector: remove unexist field description
page_pool: refill page when alloc.count of pool is zero
...
Linus Torvalds [Fri, 14 Feb 2020 20:34:30 +0000 (12:34 -0800)]
Merge tag 'pm-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix three issues related to the handling of wakeup events signaled
through the ACPI SCI while suspended to idle (Rafael Wysocki) and
unexport an internal cpufreq variable (Yangtao Li)"
* tag 'pm-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system
ACPICA: Introduce acpi_any_gpe_status_set()
ACPI: PM: s2idle: Avoid possible race related to the EC GPE
ACPI: EC: Fix flushing of pending work
cpufreq: Make cpufreq_global_kobject static
Linus Torvalds [Fri, 14 Feb 2020 20:27:54 +0000 (12:27 -0800)]
Merge tag 'sound-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The only common change is the regression fix of the previous PCM fix
patch for managed buffers while the rest are usual suspects, USB-audio
and HD-audio device-specific quirks.
The change for UAC2 clock validation workaround became a bit big, but
the changes are fairly straightforward"
* tag 'sound-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Fix double hw_free calls
ALSA: usb-audio: Add clock validity quirk for Denon MC7000/MCX8000
ALSA: hda/realtek - Fix silent output on MSI-GL73
ALSA: hda/realtek - Add more codec supported Headset Button
ALSA: usb-audio: Apply sample rate quirk for Audioengine D1
ALSA: usb-audio: Fix UAC2/3 effect unit parsing
ALSA: usb-audio: Apply 48kHz fixed rate playback for Jabra Evolve 65 headset
Linus Torvalds [Fri, 14 Feb 2020 20:23:16 +0000 (12:23 -0800)]
Merge tag 'drm-fixes-2020-02-14' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"The core has a build fix for edid code on certain compilers/arches/,
one MST fix and one vgem fix. Regular amdgpu fixes, and a couple of
small driver fixes.
The i915 fixes are bit larger than normal for this stage, but they
were having CI issues last week, and they hadn't sent any fixes last
week due to this.
core:
- edid build fix
mst:
- fix NULL ptr deref
vgem:
- fix close after free
msm:
- better dma-api usage
sun4i:
- disable allow_fb_modifiers
amdgpu:
- Additional OD fixes for navi
- Misc display fixes
- VCN 2.5 DPG fix
- Prevent build errors on PowerPC on some configs
- GDS EDC fix
* tag 'drm-fixes-2020-02-14' of git://anongit.freedesktop.org/drm/drm: (50 commits)
drm/i915: Mark the removal of the i915_request from the sched.link
drm/i915/execlists: Reclaim the hanging virtual request
drm/i915/execlists: Take a reference while capturing the guilty request
drm/i915/execlists: Offline error capture
drm/i915/gt: Allow temporary suspension of inflight requests
drm/i915: Keep track of request among the scheduling lists
drm/i915/gem: Tighten checks and acquiring the mmap object
drm/i915: Fix preallocated barrier list append
drm/i915/gt: Acquire ce->active before ce->pin_count/ce->pin_mutex
drm/i915: Tighten atomicity of i915_active_acquire vs i915_active_release
drm/i915: Stub out i915_gpu_coredump_put
drm/amdgpu:/navi10: use the ODCAP enum to index the caps array
drm/amdgpu: update smu_v11_0_pptable.h
drm/amdgpu: correct comment to clear up the confusion
drm/amd/display: DCN2.x Do not program DPPCLK if same value
drm/amd/display: Don't map ATOM_ENABLE to ATOM_INIT
drm/amdgpu/vcn2.5: fix warning
drm/amdgpu: limit GDS clearing workaround in cold boot sequence
drm/amdgpu: fix amdgpu pmu to use hwc->config instead of hwc->conf
amdgpu: Prevent build errors regarding soft/hard-float FP ABI tags
...
Randy Dunlap [Thu, 13 Feb 2020 06:28:20 +0000 (22:28 -0800)]
netdevice.h: fix all kernel-doc and Sphinx warnings
Eliminate all kernel-doc and Sphinx warnings in
<linux/netdevice.h>. Fixes these warnings:
../include/linux/netdevice.h:2100: warning: Function parameter or member 'gso_partial_features' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'l3mdev_ops' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xfrmdev_ops' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'tlsdev_ops' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'name_assign_type' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'ieee802154_ptr' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'mpls_ptr' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xdp_prog' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'gro_flush_timeout' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xdp_bulkq' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xps_cpus_map' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'xps_rxqs_map' not described in 'net_device'
../include/linux/netdevice.h:2100: warning: Function parameter or member 'qdisc_hash' not described in 'net_device'
../include/linux/netdevice.h:3552: WARNING: Inline emphasis start-string without end-string.
../include/linux/netdevice.h:3552: WARNING: Inline emphasis start-string without end-string.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Feb 2020 15:34:51 +0000 (07:34 -0800)]
Merge branch 'dsa-headroom'
Per Forlin says:
====================
net: dsa: Make sure there is headroom for tag
Sorry for re-posting yet another time....
I manage to include multiple email-senders and forgot to include cover-letter.
Let's hope everyhthing is in order this time.
Fix two tag drivers to make sure there is headroom for the tag data.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Per Forlin [Thu, 13 Feb 2020 14:37:10 +0000 (15:37 +0100)]
net: dsa: tag_ar9331: Make sure there is headroom for tag
Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Per Forlin [Thu, 13 Feb 2020 14:37:09 +0000 (15:37 +0100)]
net: dsa: tag_qca: Make sure there is headroom for tag
Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.
Signed-off-by: Per Forlin <perfn@axis.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
William Dauchy [Thu, 13 Feb 2020 17:19:22 +0000 (18:19 +0100)]
net, ip6_tunnel: enhance tunnel locate with link check
With ipip, it is possible to create an extra interface explicitly
attached to a given physical interface:
# ip link show tunl0
4: tunl0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ipip 0.0.0.0 brd 0.0.0.0
# ip link add tunl1 type ipip dev eth0
# ip link show tunl1
6: tunl1@eth0: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ipip 0.0.0.0 brd 0.0.0.0
But it is not possible with ip6tnl:
# ip link show ip6tnl0
5: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/tunnel6 :: brd ::
# ip link add ip6tnl1 type ip6tnl dev eth0
RTNETLINK answers: File exists
This patch aims to make it possible by adding link comparaison in both
tunnel locate and lookup functions; we also modify mtu calculation when
attached to an interface with a lower mtu.
This permits to make use of x-netns communication by moving the newly
created tunnel in a given netns.
Signed-off-by: William Dauchy <w.dauchy@criteo.com> Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Feb 2020 15:16:08 +0000 (07:16 -0800)]
Merge tag 'mac80211-for-net-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a few fixes:
* avoid running out of tracking space for frames that need
to be reported to userspace by using more bits
* fix beacon handling suppression by adding some relevant
elements to the CRC calculation
* fix quiet mode in action frames
* fix crash in ethtool for virt_wifi and similar
* add a missing policy entry
* fix 160 & 80+80 bandwidth to take local capabilities into
account
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 14 Feb 2020 07:59:00 +0000 (08:59 +0100)]
net/smc: no peer ID in CLC decline for SMCD
Just SMCR requires a CLC Peer ID, but not SMCD. The field should be
zero for SMCD.
Fixes: 00b917c03235 ("net/smc: add SMC-D support in CLC messages") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 14 Feb 2020 07:58:59 +0000 (08:58 +0100)]
net/smc: transfer fasync_list in case of fallback
SMC does not work together with FASTOPEN. If sendmsg() is called with
flag MSG_FASTOPEN in SMC_INIT state, the SMC-socket switches to
fallback mode. To handle the previous ioctl FIOASYNC call correctly
in this case, it is necessary to transfer the socket wait queue
fasync_list to the internal TCP socket.
Reported-by: syzbot+4b1fe8105f8044a26162@syzkaller.appspotmail.com Fixes: 8d716f2265c89 ("net/smc: handle sockopts forcing fallback") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 14 Feb 2020 15:05:18 +0000 (07:05 -0800)]
Merge branch 'hns3-fixes'
Huazhong Tan says:
====================
net: hns3: fixes for -net
This series includes three bugfixes for the HNS3 ethernet driver.
[patch 1] fixes a management table lost issue after IMP reset.
[patch 2] fixes a VF bandwidth configuration not work problem.
[patch 3] fixes a problem related to IPv6 address copying.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guangbin Huang [Fri, 14 Feb 2020 01:53:43 +0000 (09:53 +0800)]
net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()
The IPv6 address defined in struct in6_addr is specified as
big endian, but there is no specified endian in struct
hclge_fd_rule_tuples, so it will cause a problem if directly
use memcpy() to copy ipv6 address between these two structures
since this field in struct hclge_fd_rule_tuples is little endian.
This patch fixes this problem by using be32_to_cpu() to convert
endian of IPv6 address of struct in6_addr before copying.
Fixes: 311b0277f0f2 ("net: hns3: add aRFS support for PF") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu [Fri, 14 Feb 2020 01:53:42 +0000 (09:53 +0800)]
net: hns3: fix VF bandwidth does not take effect in some case
When enabling 4 TC after setting the bandwidth of VF, the bandwidth
of VF will resume to default value, because of the qset resources
changed in this case.
This patch fixes it by using a fixed VF's qset resources according to
HNAE3_MAX_TC macro.
Fixes: 959fbccef807 ("net: hns3: add support for configuring bandwidth of VF on the host") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yufeng Mo [Fri, 14 Feb 2020 01:53:41 +0000 (09:53 +0800)]
net: hns3: add management table after IMP reset
In the current process, the management table is missing after the
IMP reset. This patch adds the management table to the reset process.
Fixes: a36633ff8784 ("net: hns3: add manager table initialization for hardware") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Crispin [Tue, 11 Feb 2020 12:26:04 +0000 (13:26 +0100)]
mac80211: allow setting queue_len for drivers not using wake_tx_queue
Currently a mac80211 driver can only set the txq_limit when using
wake_tx_queue. Not all drivers use wake_tx_queue. This patch adds a new
element to wiphy allowing a driver to set a custom tx_queue_len and the
code that will apply it in case it is set. The current default is
1000 which is too low for ath11k when doing HE rates.
Shay Bar [Mon, 10 Feb 2020 13:07:28 +0000 (15:07 +0200)]
mac80211: fix wrong 160/80+80 MHz setting
Before this patch, STA's would set new width of 160/80+80 MHz based on AP capability only.
This is wrong because STA may not support > 80MHz BW.
Fix is to verify STA has 160/80+80 MHz capability before increasing its width to > 80MHz.
The "support_80_80" and "support_160" setting is based on:
"Table 9-272 — Setting of the Supported Channel Width Set subfield and Extended NSS BW
Support subfield at a STA transmitting the VHT Capabilities Information field"
From "Draft P802.11REVmd_D3.0.pdf"
Dave Airlie [Fri, 14 Feb 2020 03:03:51 +0000 (13:03 +1000)]
Merge tag 'drm-intel-next-fixes-2020-02-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.6-rc2
Most of these were aimed at a "next fixes" pull already during the merge
window, but there were issues with the baseline I used, which resulted
in a lot of issues in CI. I've regenerated this stuff piecemeal now,
adding gradually to it, and it seems healthy now.
Due to the issues this is much bigger than I'd like. But it was
obviously necessary to take the time to ensure it's not garbage...
Dave Airlie [Fri, 14 Feb 2020 02:52:49 +0000 (12:52 +1000)]
Merge tag 'drm-misc-fixes-2020-02-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v5.6:
- Revert allow_fb_modifiers in sun4i, as it causes a regression for DE2 and DE3.
- Fix null pointer deref in drm_dp_mst_process_up_req().
Linus Torvalds [Thu, 13 Feb 2020 22:36:57 +0000 (14:36 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Summary below, but it's all reasonably straightforward. There are some
more fixes on the horizon, but nothing disastrous yet.
Summary:
- Fix build when KASLR is enabled but CONFIG_ARCH_RANDOM is not set
- Fix context-switching of SSBS state on systems that implement it
- Fix spinlock compiler warning introduced during the merge window
- Use SYSCTL_{ZERO,ONE} instead of rolling our own static variables
- Don't scream if optional SMMUv3 PMU irq is missing
- Remove some unused function prototypes"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: time: Replace <linux/clk-provider.h> by <linux/of_clk.h>
arm64: Fix CONFIG_ARCH_RANDOM=n build
perf/smmuv3: Use platform_get_irq_optional() for wired interrupt
arm64/spinlock: fix a -Wunused-function warning
arm64: ssbs: Fix context-switch when SSBS is present on all CPUs
arm64: use shared sysctl constants
arm64: Drop do_el0_ia_bp_hardening() & do_sp_pc_abort() declarations
Linus Torvalds [Thu, 13 Feb 2020 22:34:58 +0000 (14:34 -0800)]
Merge tag 'gpio-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- Revert two patches to gpio_do_set_config() and implement the proper
solution that works, also drop an unecessary call in set_config()
- Fix up the lockdep class for hierarchical IRQ domains.
- Remove some bridge code for line directions.
- Fix a register access bug in the Xilinx driver.
* tag 'gpio-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: sifive: fix static checker warning
spmi: pmic-arb: Set lockdep class for hierarchical irq domains
gpio: xilinx: Fix bug where the wrong GPIO register is written to
gpiolib: remove unnecessary argument from set_config call
gpio: bd71828: Remove unneeded defines for GPIO_LINE_DIRECTION_IN/OUT
MAINTAINERS: Sort entries in database for GPIO
gpiolib: fix gpio_do_set_config()
Revert "gpiolib: remove set but not used variable 'config'"
Revert "gpiolib: Remove duplicated function gpio_do_set_config()"
====================
icmp: account for NAT when sending icmps from ndo layer
The ICMP routines use the source address for two reasons:
1. Rate-limiting ICMP transmissions based on source address, so
that one source address cannot provoke a flood of replies. If
the source address is wrong, the rate limiting will be
incorrectly applied.
2. Choosing the interface and hence new source address of the
generated ICMP packet. If the original packet source address
is wrong, ICMP replies will be sent from the wrong source
address, resulting in either a misdelivery, infoleak, or just
general network admin confusion.
Most of the time, the icmp_send and icmpv6_send routines can just reach
down into the skb's IP header to determine the saddr. However, if
icmp_send or icmpv6_send is being called from a network device driver --
there are a few in the tree -- then it's possible that by the time
icmp_send or icmpv6_send looks at the packet, the packet's source
address has already been transformed by SNAT or MASQUERADE or some other
transformation that CONNTRACK knows about. In this case, the packet's
source address is most certainly the *wrong* source address to be used
for the purpose of ICMP replies.
Rather, the source address we want to use for ICMP replies is the
original one, from before the transformation occurred.
Fortunately, it's very easy to just ask CONNTRACK if it knows about this
packet, and if so, how to fix it up. The saddr is the only field in the
header we need to fix up, for the purposes of the subsequent processing
in the icmp_send and icmpv6_send functions, so we do the lookup very
early on, so that the rest of the ICMP machinery can progress as usual.
Changes v3->v4:
- Add back the skb_shared checking, since the previous assumption isn't
actually true [Eric]. This implies dropping the additional patches v3 had
for removing skb_share_check from various drivers. We can revisit that
general set of ideas later, but that's probably better suited as a net-next
patchset rather than this stable one which is geared at fixing bugs. So,
this implements things in the safe conservative way.
Changes v2->v3:
- Add selftest to ensure this actually does what we want and never regresses.
- Check the size of the skb header before operating on it.
- Use skb_ensure_writable to ensure we can modify the cloned skb [Florian].
- Conditionalize this on IPS_SRC_NAT so we don't do anything unnecessarily
[Florian].
- It turns out that since we're calling these from the xmit path,
skb_share_check isn't required, so remove that [Florian]. This simplifes the
code a bit too. **The supposition here is that skbs passed to ndo_start_xmit
are _never_ shared. If this is not correct NOW IS THE TIME TO PIPE UP, for
doom awaits us later.**
- While investigating the shared skb business, several drivers appeared to be
calling it incorrectly in the xmit path, so this series also removes those
unnecessary calls, based on the supposition mentioned in the previous point.
Changes v1->v2:
- icmpv6 takes subtly different types than icmpv4, like u32 instead of be32,
u8 instead of int.
- Since we're technically writing to the skb, we need to make sure it's not
a shared one [Dave, 2017].
- Restore the original skb data after icmp_send returns. All current users
are freeing the packet right after, so it doesn't matter, but future users
might not.
- Remove superfluous route lookup in sunvnet [Dave].
- Use NF_NAT instead of NF_CONNTRACK for condition [Florian].
- Include this cover letter [Dave].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Because xfrmi is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Because wireguard is calling icmp from network device context, it should
use the ndo helper so that the rate limiting applies correctly. This
commit adds a small test to the wireguard test suite to ensure that the
new functions continue doing the right thing in the context of
wireguard. It does this by setting up a condition that will definately
evoke an icmp error message from the driver, but along a nat'd path.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Because sunvnet is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly. While we're
at it, doing the additional route lookup before calling icmp_ndo_send is
superfluous, since this is the job of the icmp code in the first place.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
icmp: introduce helper for nat'd source address in network device context
This introduces a helper function to be called only by network drivers
that wraps calls to icmp[v6]_send in a conntrack transformation, in case
NAT has been used. We don't want to pollute the non-driver path, though,
so we introduce this as a helper to be called by places that actually
make use of this, as suggested by Florian.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Tue, 11 Feb 2020 18:33:40 +0000 (19:33 +0100)]
net/sched: flower: add missing validation of TCA_FLOWER_FLAGS
unlike other classifiers that can be offloaded (i.e. users can set flags
like 'skip_hw' and 'skip_sw'), 'cls_flower' doesn't validate the size of
netlink attribute 'TCA_FLOWER_FLAGS' provided by user: add a proper entry
to fl_policy.
Fixes: 609f1261c1c5 ("net/flower: Introduce hardware offload support") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Tue, 11 Feb 2020 18:33:39 +0000 (19:33 +0100)]
net/sched: matchall: add missing validation of TCA_MATCHALL_FLAGS
unlike other classifiers that can be offloaded (i.e. users can set flags
like 'skip_hw' and 'skip_sw'), 'cls_matchall' doesn't validate the size
of netlink attribute 'TCA_MATCHALL_FLAGS' provided by user: add a proper
entry to mall_policy.
Fixes: 2385c6d25b98 ("net/sched: Add match-all classifier hw offloading.") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 11 Feb 2020 10:31:54 +0000 (18:31 +0800)]
net/flow_dissector: remove unexist field description
@thoff has moved to struct flow_dissector_key_control.
Fixes: 327dc61f00df ("net: Get skb hash over flow_keys structure") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Tue, 11 Feb 2020 02:13:44 +0000 (10:13 +0800)]
page_pool: refill page when alloc.count of pool is zero
"do {} while" in page_pool_refill_alloc_cache will always
refill page once whether refill is true or false, and whether
alloc.count of pool is less than PP_ALLOC_CACHE_REFILL or not
this is wrong, and will cause overflow of pool->alloc.cache
the caller of __page_pool_get_cached should provide guarantee
that pool->alloc.cache is safe to access, so in_serving_softirq
should be removed as suggested by Jesper Dangaard Brouer in
https://patchwork.ozlabs.org/patch/1233713/
so fix this issue by calling page_pool_refill_alloc_cache()
only when pool->alloc.count is zero
Fixes: 03f9ed77591e ("page_pool: handle page recycle for NUMA_NO_NODE condition") Signed-off-by: Li RongQing <lirongqing@baidu.com> Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 13 Feb 2020 22:10:11 +0000 (14:10 -0800)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-02-12
This series contains fixes to only the ice driver.
Dave fixes logic flaws in the DCB rebuild function which is used after a
reset. Also fixed a configuration issue when switching between firmware
and software LLDP mode where the number of TLV's configured was getting
out of sync with what lldpad thinks is configured.
Paul fixes how the driver displayed all the supported and advertised
link modes by basing it on the PHY capabilities, and in the process
cleaned up a lot of code.
Brett fixes duplicate receive tail bumps by comparing the value we are
writing to tail with the previously written tail value. Also cleaned up
workarounds that are no longer needed with the latest NVM images.
Anirudh cleaned up unnecessary CONFIG_PCI_IOV wrappers. Updated the
driver to use ice_pf_to_dev() instead of &pf->pdev->dev or
&vsi->back->pdev->dev. Cleaned up the string format in print function
calls to remove newlines where applicable.
Akeem updates the link message logging to include "Full Duplex" and
"Negotiated", to help distinguish from "Requested" for FEC.
Bruce fixes and consolidates the logging of firmware/NVM information
during driver load, since the information is duplicate of what is
available via ethtool. Fixed the checking of the Unit Load Status bits
after reset to ensure they are 0x7FF before continuing, by updating the
mask. Cleanup up possible NULL dereferences that were created by a
previous commit.
Ben fixes the driver to use the correct netif_msg_tx/rx_error() to
determine whether to print the MDD event type.
Tony provides several trivial fixes, which include whitespace, typos,
function header comments, reverse Christmas tree issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Thu, 13 Feb 2020 06:03:49 +0000 (07:03 +0100)]
ALSA: pcm: Fix double hw_free calls
The commit b8837064ce40 ("ALSA: pcm: Fix memory leak at closing a
stream without hw_free") tried to fix the regression wrt the missing
hw_free call at closing without SNDRV_PCM_IOCTL_HW_FREE ioctl.
However, the code change dropped mistakenly the state check, resulting
in calling hw_free twice when SNDRV_PCM_IOCTL_HW_FRE got called
beforehand. For most drivers, this is almost harmless, but the
drivers like SOF show another regression now.
This patch adds the state condition check before calling do_hw_free()
at releasing the stream for avoiding the double hw_free calls.
Alexander Tsoy [Wed, 12 Feb 2020 23:54:50 +0000 (02:54 +0300)]
ALSA: usb-audio: Add clock validity quirk for Denon MC7000/MCX8000
It should be safe to ignore clock validity check result if the following
conditions are met:
- only one single sample rate is supported;
- the terminal is directly connected to the clock source;
- the clock type is internal.
This is to deal with some Denon DJ controllers that always reports that
clock is invalid.
Randy Dunlap [Mon, 10 Feb 2020 03:36:14 +0000 (19:36 -0800)]
linux/pipe_fs_i.h: fix kernel-doc warnings after @wait was split
Fix kernel-doc warnings in struct pipe_inode_info after @wait was
split into @rd_wait and @wr_wait.
include/linux/pipe_fs_i.h:66: warning: Function parameter or member 'rd_wait' not described in 'pipe_inode_info'
include/linux/pipe_fs_i.h:66: warning: Function parameter or member 'wr_wait' not described in 'pipe_inode_info'
Fixes: 5550506a0b46 ("pipe: use exclusive waits when reading or writing") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tony Nguyen [Thu, 6 Feb 2020 09:20:13 +0000 (01:20 -0800)]
ice: Trivial fixes
This is a collection of trivial fixes including fixing whitespace, typos,
function headers, reverse Christmas tree, etc.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ben Shelton [Thu, 6 Feb 2020 09:20:12 +0000 (01:20 -0800)]
ice: Use correct netif error function
Use the correct netif_msg_[tx,rx]_error() function to determine whether to
print the MDD event type.
Signed-off-by: Ben Shelton <benjamin.h.shelton@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Formatting strings in print function calls (like dev_info, dev_err, etc.)
can exceed 80 columns without making checkpatch unhappy. So remove
newlines where applicable and make print statements more compact.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ice_pf_to_dev(pf) instead of &pf->pdev->dev
Use ice_pf_to_dev(vsi->back) instead of &vsi->back->pdev->dev
When a pointer to the pf instance is available, use ice_pf_to_dev
instead of ice_hw_to_dev
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Nguyen [Thu, 6 Feb 2020 09:20:08 +0000 (01:20 -0800)]
ice: Remove possible null dereference
Commit b60675373518 ("ice: add extra check for null Rx descriptor") moved
the call to ice_construct_skb() under a null check as Coverity reported a
possible use of null skb. However, the original call was not deleted, do so
now.
Fixes: b60675373518 ("ice: add extra check for null Rx descriptor") Reported-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Thu, 6 Feb 2020 09:20:07 +0000 (01:20 -0800)]
ice: update Unit Load Status bitmask to check after reset
After a reset the Unit Load Status bits in the GLNVM_ULD register to check
for completion should be 0x7FF before continuing. Update the mask to check
(minus the three reserved bits that are always set).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Thu, 6 Feb 2020 09:20:06 +0000 (01:20 -0800)]
ice: fix and consolidate logging of NVM/firmware version information
Logging the firmware/NVM information during driver load is redundant since
that information is also available via ethtool. Move the functionality
found in ice_nvm_version_str() directly into ice_get_drvinfo() and remove
calling the former and logging that info during driver probe. This also
gets rid of a bug in ice_nvm_version_str() where it returns a pointer to
a buffer which is free'ed when that function exits.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies link message logging to include "Full Duplex" and
"Negotiated" for FEC, so as to distinguish it from "Requested" FEC.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice: Remove CONFIG_PCI_IOV wrap in ice_set_pf_caps
Remove unnecessary CONFIG_PCI_IOV wrapping in ice_set_pf_caps. None
of the data structures accessed within the block are wrapped with
this flag. When CONFIG_PCI_IOV is undefined, pf->num_vfs_supported
will be 0 anyway.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 6 Feb 2020 09:20:03 +0000 (01:20 -0800)]
ice: Remove ice_dev_onetime_setup()
ice_dev_onetime_setup contains driver workarounds needed for
firmware limitations. These issues have now been resolved in newer
NVMs so remove the function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 6 Feb 2020 09:20:02 +0000 (01:20 -0800)]
ice: Don't allow same value for Rx tail to be written twice
Currently we compare the value we are about to write to the Rx tail
register with the previous value of next_to_use. The problem with this
is we only write tail on 8 descriptor boundaries, but next_to_use is
updated whenever we clean Rx descriptors. Fix this by comparing the
value we are about to write to tail with the previously written tail
value. This will prevent duplicate Rx tail bumps.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Paul Greenwalt [Thu, 6 Feb 2020 09:20:01 +0000 (01:20 -0800)]
ice: display supported and advertised link modes
Display all of the supported and advertised link modes based on the PHY
capability with media.
Displaying all supported modes is more informative then only displaying
the current link mode.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dave Ertman [Thu, 6 Feb 2020 09:20:00 +0000 (01:20 -0800)]
ice: Fix switch between FW and SW LLDP
When switching between FW and SW LLDP mode, the
number of configured TLV apps in the driver's
DCB configuration is getting out of synch with
what lldpad thinks is configured. This is causing
a problem when shutting down lldpad. The cleanup
is trying to delete TLV apps that are not defined
in the kernel.
Since the driver is keeping an accurate account
of the apps defined, use the drivers number of
apps to determine if there is an app to delete.
If the number of apps is <= 1, then do not
attempt to delete.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dave Ertman [Thu, 6 Feb 2020 09:19:59 +0000 (01:19 -0800)]
ice: Fix DCB rebuild after reset
The function ice_dcb_rebuild had some logic
flaws in it, and also didn't differentiate
between FW and SW modes needs.
For FW flow, the willing setting was being
forced to OFF and left that way. Unwilling
in DCB FW mode is not a supported model.
Leave the config alone and use the return value
from the set command to determine if setting the
config was successful.
The SW DCB flow does not need to need to register
for MIB change events (as they are not used in
SW mode).
Use !is_sw_lldp checks to only perform FW specific
task while in FW mode.
Also adding a reapplication of the current DCB
config after a link event. Some NVMs are not
maintaining their DCB configs across link events.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Wed, 12 Feb 2020 18:28:42 +0000 (10:28 -0800)]
Merge tag 'kbuild-fixes-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- fix memory corruption in scripts/kallsyms
- fix the vmlinux link stage to correctly update compile.h
* tag 'kbuild-fixes-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: fix mismatch between .version and include/generated/compile.h
scripts/kallsyms: fix memory corruption caused by write over-run
Kunihiko Hayashi [Wed, 12 Feb 2020 10:55:34 +0000 (19:55 +0900)]
net: ethernet: ave: Add capability of rgmii-id mode
This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Firo Yang [Wed, 12 Feb 2020 05:09:17 +0000 (06:09 +0100)]
enic: prevent waking up stopped tx queues over watchdog reset
Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090
After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.
After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
enic_poll_msix_wq->
vnic_cq_service->
enic_wq_service->
netif_wake_subqueue(enic->netdev, q_number)->
test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.
Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.
Signed-off-by: Firo Yang <firo.yang@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Wilson [Wed, 22 Jan 2020 14:02:43 +0000 (14:02 +0000)]
drm/i915: Mark the removal of the i915_request from the sched.link
Keep the rq->fence.flags consistent with the status of the
rq->sched.link, and clear the associated bits when decoupling the link
on retirement (as we may wish to inspect those flags independent of
other state).
Chris Wilson [Wed, 22 Jan 2020 14:02:42 +0000 (14:02 +0000)]
drm/i915/execlists: Reclaim the hanging virtual request
If we encounter a hang on a virtual engine, as we process the hang the
request may already have been moved back to the virtual engine (we are
processing the hang on the physical engine). We need to reclaim the
request from the virtual engine so that the locking is consistent and
local to the real engine on which we will hold the request for error
state capturing.
v2: Pull the reclamation into execlists_hold() and assert that cannot be
called from outside of the reset (i.e. with the tasklet disabled).
v3: Added selftest
v4: Drop the reference owned by the virtual engine
projects / kernel.git / log