Roy Novich [Wed, 26 Oct 2022 13:51:48 +0000 (14:51 +0100)]
net/mlx5: Update fw fatal reporter state on PCI handlers successful recover
Update devlink health fw fatal reporter state to "healthy" is needed by
strictly calling devlink_health_reporter_state_update() after recovery
was done by PCI error handler. This is needed when fw_fatal reporter was
triggered due to PCI error. Poll health is called and set reporter state
to error. Health recovery failed (since EEH didn't re-enable the PCI).
PCI handlers keep on recover flow and succeed later without devlink
acknowledgment. Fix this by adding devlink state update at the end of
the PCI handler recovery process.
Fixes: 9f97bae32159 ("devlink: add support for reporter recovery completion") Signed-off-by: Roy Novich <royno@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Aya Levin <ayal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-11-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Roi Dayan [Wed, 26 Oct 2022 13:51:47 +0000 (14:51 +0100)]
net/mlx5e: TC, Fix cloned flow attr instance dests are not zeroed
On multi table split the driver creates a new attr instance with
data being copied from prev attr instance zeroing action flags.
Also need to reset dests properties to avoid incorrect dests per attr.
Fixes: eab22a3adb09 ("net/mlx5e: Create new flow attr for multi table actions") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-10-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ariel Levkovich [Wed, 26 Oct 2022 13:51:46 +0000 (14:51 +0100)]
net/mlx5e: TC, Reject forwarding from internal port to internal port
Reject TC rules that forward from internal port to internal port
as it is not supported.
This include rules that are explicitly have internal port as
the filter device as well as rules that apply on tunnel interfaces
as the route device for the tunnel interface can be an internal
port.
Fixes: b8c4d8174a56 ("net/mlx5e: Offload tc rules that redirect to ovs internal port") Signed-off-by: Ariel Levkovich <lariel@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-9-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan [Wed, 26 Oct 2022 13:51:45 +0000 (14:51 +0100)]
net/mlx5: Fix possible use-after-free in async command interface
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr ffff888139cd12f4 by task swapper/5/0
Saeed Mahameed [Wed, 26 Oct 2022 13:51:44 +0000 (14:51 +0100)]
net/mlx5: ASO, Create the ASO SQ with the correct timestamp format
mlx5 SQs must select the timestamp format explicitly according to the
active clock mode, select the current active timestamp mode so ASO SQ create
will succeed.
This fixes the following error prints when trying to create ipsec ASO SQ
while the timestamp format is real time mode.
mlx5_cmd_out_err:778:(pid 34874): CREATE_SQ(0x904) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xd61c0b), err(-22)
mlx5_aso_create_sq:285:(pid 34874): Failed to open aso wq sq, err=-22
mlx5e_ipsec_init:436:(pid 34874): IPSec initialization failed, -22
Fixes: 8a033da206b2 ("net/mlx5: Add support to create SQ and CQ for ASO") Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Reported-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-7-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paul Blakey [Wed, 26 Oct 2022 13:51:43 +0000 (14:51 +0100)]
net/mlx5e: Update restore chain id for slow path packets
Currently encap slow path rules just forward to software without
setting the chain id miss register, so driver doesn't restore
the chain, and packets hitting this rule will restart from tc chain
0 instead of continuing to the chain the encap rule was on.
Fix this by setting the chain id miss register to the chain id mapping.
Fixes: 08893db24614 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping") Signed-off-by: Paul Blakey <paulb@nvidia.com> Reviewed-by: Oz Shlomo <ozsh@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-6-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aya Levin [Wed, 26 Oct 2022 13:51:42 +0000 (14:51 +0100)]
net/mlx5e: Extend SKB room check to include PTP-SQ
When tx_port_ts is set, the driver diverts all UPD traffic over PTP port
to a dedicated PTP-SQ. The SKBs are cached until the wire-CQE arrives.
When the packet size is greater then MTU, the firmware might drop it and
the packet won't be transmitted to the wire, hence the wire-CQE won't
reach the driver. In this case the SKBs are accumulated in the SKB fifo.
Add room check to consider the PTP-SQ SKB fifo, when the SKB fifo is
full, driver stops the queue resulting in a TX timeout. Devlink
TX-reporter can recover from it.
Fixes: f90a1134a383 ("net/mlx5e: Add TX port timestamp support") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-5-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rongwei Liu [Wed, 26 Oct 2022 13:51:41 +0000 (14:51 +0100)]
net/mlx5: DR, Fix matcher disconnect error flow
When 2nd flow rules arrives, it will merge together with the
1st one if matcher criteria is the same.
If merge fails, driver will rollback the merge contents, and
reject the 2nd rule. At rollback stage, matcher can't be
disconnected unconditionally, otherise the 1st rule can't be
hit anymore.
Add logic to check if the matcher should be disconnected or not.
Fixes: 9e165e6798d3 ("net/mlx5: DR, Improve steering for empty or RX/TX-only matchers") Signed-off-by: Rongwei Liu <rongweil@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-4-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Moshe Shemesh [Wed, 26 Oct 2022 13:51:40 +0000 (14:51 +0100)]
net/mlx5: Wait for firmware to enable CRS before pci_restore_state
After firmware reset driver should verify firmware already enabled CRS
and became responsive to pci config cycles before restoring pci state.
Fix that by waiting till device_id is readable through PCI again.
Hyong Youb Kim [Wed, 26 Oct 2022 13:51:39 +0000 (14:51 +0100)]
net/mlx5e: Do not increment ESN when updating IPsec ESN state
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes: 3bd5d190cb51 ("net/mlx5: IPSec, Add support for ESN") Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com> Acked-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao [Wed, 26 Oct 2022 01:46:42 +0000 (09:46 +0800)]
netdevsim: remove dir in nsim_dev_debugfs_init() when creating ports dir failed
Remove dir in nsim_dev_debugfs_init() when creating ports dir failed.
Otherwise, the netdevsim device will not be created next time. Kernel
reports an error: debugfs: Directory 'netdevsim1' with parent 'netdevsim'
already present!
Fixes: 67737eb43aac ("netdevsim: change debugfs tree topology") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao [Wed, 26 Oct 2022 01:54:05 +0000 (09:54 +0800)]
netdevsim: fix memory leak in nsim_bus_dev_new()
If device_register() failed in nsim_bus_dev_new(), the value of reference
in nsim_bus_dev->dev is 1. obj->name in nsim_bus_dev->dev will not be
released.
Jakub Kicinski [Thu, 27 Oct 2022 17:30:41 +0000 (10:30 -0700)]
Merge tag 'linux-can-fixes-for-6.1-20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-10-27
Anssi Hannula fixes the use of the completions in the kvaser_usb
driver.
Biju Das contributes 2 patches for the rcar_canfd driver. A IRQ storm
that can be triggered by high CAN bus load and channel specific IRQ
handlers are fixed.
Yang Yingliang fixes the j1939 transport protocol by moving a
kfree_skb() out of a spin_lock_irqsave protected section.
* tag 'linux-can-fixes-for-6.1-20221027' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: j1939: transport: j1939_session_skb_drop_old(): spin_unlock_irqrestore() before kfree_skb()
can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive
can: kvaser_usb: Fix possible completions during init_completion
====================
Rafał Miłecki [Thu, 27 Oct 2022 11:24:30 +0000 (13:24 +0200)]
net: broadcom: bcm4908_enet: update TX stats after actual transmission
Queueing packets doesn't guarantee their transmission. Update TX stats
after hardware confirms consuming submitted data.
This also fixes a possible race and NULL dereference.
bcm4908_enet_start_xmit() could try to access skb after freeing it in
the bcm4908_enet_poll_tx().
====================
ip: rework the fix for dflt addr selection for connected nexthop"
This series reworks the fix that is reverted in the second commit.
As Julian explained, nhc_scope is related to nhc_gw, it's not the scope of
the route.
====================
Nicolas Dichtel [Thu, 20 Oct 2022 10:09:52 +0000 (12:09 +0200)]
nh: fix scope used to find saddr when adding non gw nh
As explained by Julian, fib_nh_scope is related to fib_nh_gw4, but
fib_info_update_nhc_saddr() needs the scope of the route, which is
the scope "before" fib_nh_scope, ie fib_nh_scope - 1.
This patch fixes the problem described in commit 4be009aa4a33 ("ip: fix
dflt addr selection for connected nexthop").
As explained by Julian, nhc_scope is related to nhc_gw, not to the route.
Revert the original patch. The initial problem is fixed differently in the
next commit.
Jakub Kicinski [Wed, 26 Oct 2022 00:15:24 +0000 (17:15 -0700)]
genetlink: limit the use of validation workarounds to old ops
During review of previous change another thing came up - we should
limit the use of validation workarounds to old commands.
Don't list the workarounds one by one, as we're rejecting all existing
ones. We can deal with the masking in the unlikely event that new flag
is added.
Florian Fainelli [Tue, 25 Oct 2022 23:42:01 +0000 (16:42 -0700)]
net: bcmsysport: Indicate MAC is in charge of PHY PM
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The SYSTEMPORT
driver essentially does exactly what mdio_bus_phy_resume() does by
calling phy_resume().
Yang Yingliang [Thu, 27 Oct 2022 09:12:37 +0000 (17:12 +0800)]
can: j1939: transport: j1939_session_skb_drop_old(): spin_unlock_irqrestore() before kfree_skb()
It is not allowed to call kfree_skb() from hardware interrupt context
or with interrupts being disabled. The skb is unlinked from the queue,
so it can be freed after spin_unlock_irqrestore().
Fixes: 877b9bba3266 ("can: add support of SAE J1939 protocol") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/all/20221027091237.2290111-1-yangyingliang@huawei.com Cc: stable@vger.kernel.org
[mkl: adjust subject] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Yang Yingliang [Tue, 25 Oct 2022 13:00:11 +0000 (21:00 +0800)]
net: ehea: fix possible memory leak in ehea_register_port()
If of_device_register() returns error, the of node and the
name allocated in dev_set_name() is leaked, call put_device()
to give up the reference that was set in device_initialize(),
so that of node is put in logical_port_release() and the name
is freed in kobject_cleanup().
====================
openvswitch: syzbot splat fix and introduce selftest
Syzbot recently caught a splat when dropping features from
openvswitch datapaths that are in-use. The WARN() call is
definitely too large a hammer for the situation, so change
to pr_warn.
Second patch in the series introduces a new selftest suite which
can help show that an issue is fixed. This change might be
more suited to net-next tree, so it has been separated out
as an additional patch and can be either applied to either tree
based on preference.
====================
Aaron Conole [Tue, 25 Oct 2022 10:50:18 +0000 (06:50 -0400)]
selftests: add openvswitch selftest suite
Previous commit resolves a WARN splat that can be difficult to reproduce,
but with the ovs-dpctl.py utility, it can be trivial. Introduce a test
case which creates a DP, and then downgrades the feature set. This will
include a utility 'ovs-dpctl.py' that can be extended to do additional
tests and diagnostics.
Signed-off-by: Aaron Conole <aconole@redhat.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Aaron Conole [Tue, 25 Oct 2022 10:50:17 +0000 (06:50 -0400)]
openvswitch: switch from WARN to pr_warn
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still
preserve the warning to the user that feature downgrade occurred. We
likely cannot introduce other kinds of checks / enforcement here because
syzbot can generate different genl versions to the datapath.
Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com Fixes: c5d24faa13b4 ("openvswitch: Drop user features if old user space attempted to create datapath") Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Aaron Conole <aconole@redhat.com> Acked-by: Ilya Maximets <i.maximets@ovn.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch series fixes the below issues in R-Car CAN-FD driver.
1) Race condition in CAN driver under heavy CAN load condition
with both channels enabled results in IRQ storm on global FIFO
receive IRQ line.
2) Add channel specific TX interrupts handling for RZ/G2L SoC as it has
separate IRQ lines for each TX.
changes since v1: https://lore.kernel.org/all/20221022081503.1051257-1-biju.das.jz@bp.renesas.com
* Added check for IRQ active and enabled before handling the IRQ on a
particular channel.
Biju Das [Tue, 25 Oct 2022 15:56:56 +0000 (16:56 +0100)]
can: rcar_canfd: fix channel specific IRQ handling for RZ/G2L
RZ/G2L has separate channel specific IRQs for transmit and error
interrupts. But the IRQ handler processes both channels, even if there
no interrupt occurred on one of the channels.
This patch fixes the issue by passing a channel specific context
parameter instead of global one for the IRQ register and the IRQ
handler, it just handles the channel which is triggered the interrupt.
Fixes: 53f37e24dc63 ("can: rcar_canfd: Add support for RZ/G2L family") Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20221025155657.1426948-3-biju.das.jz@bp.renesas.com Cc: stable@vger.kernel.org
[mkl: adjust commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Biju Das [Tue, 25 Oct 2022 15:56:55 +0000 (16:56 +0100)]
can: rcar_canfd: rcar_canfd_handle_global_receive(): fix IRQ storm on global FIFO receive
We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes: 446e069525e2 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver") Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com Cc: stable@vger.kernel.org
[mkl: adjust commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Anssi Hannula [Mon, 10 Oct 2022 18:52:27 +0000 (20:52 +0200)]
can: kvaser_usb: Fix possible completions during init_completion
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: d9f21bf91c45 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Tested-by: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Kunihiko Hayashi [Mon, 24 Oct 2022 07:22:27 +0000 (16:22 +0900)]
net: ethernet: ave: Fix MAC to be in charge of PHY PM
The phylib callback is called after MAC driver's own resume callback is
called. For AVE driver, after resuming immediately, PHY state machine is
in PHY_NOLINK because there is a time lag from link-down to link-up due to
autoneg. The result is WARN_ON() dump in mdio_bus_phy_resume().
Since ave_resume() itself calls phy_resume(), AVE driver should manage
PHY PM. To indicate that MAC driver manages PHY PM, set
phydev->mac_managed_pm to true to avoid the unnecessary phylib call and
add missing phy_init_hw() to ave_resume().
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com> Fixes: d6f853caf863 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM") Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/20221024072227.24769-1-hayashi.kunihiko@socionext.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Juergen Borleis [Mon, 24 Oct 2022 08:05:52 +0000 (10:05 +0200)]
net: fec: limit register access on i.MX6UL
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: 445ed38ace6a ("net: fec: use a more proper compatible string for i.MX6UL type device") Signed-off-by: Juergen Borleis <jbe@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "random rhlist add/delete operations" actually wasn't very random, as all
cases tested the same bit. Since the later parts of this loop depend on the
first case execute this unconditionally, and then test on different bits for the
remaining tests. While at it only request as much random bits as are actually
used.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Caleb Connolly [Mon, 24 Oct 2022 23:48:50 +0000 (00:48 +0100)]
net: ipa: don't configure IDLE_INDICATION on v3.1
IPA v3.1 doesn't support the IDLE_INDICATION_CFG register, this was
causing a harmless splat in ipa_idle_indication_cfg(), add a version
check to prevent trying to fetch this register on v3.1
Fixes: ddb9d222891d ("net: ipa: introduce ipa_reg()") Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by: Alex Elder <elder@linaro.org> Tested-by: Jami Kettunen <jami.kettunen@somainline.org> Link: https://lore.kernel.org/r/20221024234850.4049778-1-caleb.connolly@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Caleb Connolly [Mon, 24 Oct 2022 21:03:32 +0000 (22:03 +0100)]
net: ipa: fix v3.1 resource limit masks
The resource group limits for IPA v3.1 mistakenly used 6 bit wide mask
values, when the hardware actually uses 8. Out of range values were
silently ignored before, so the IPA worked as expected. However the
new generalised register definitions introduce stricter checking here,
they now cause some splats and result in the value 0 being written
instead. Fix the limit bitmask widths so that the correct values can be
written.
Fixes: d53583c6da59 ("net: ipa: define resource group/type IPA register fields") Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by: Alex Elder <elder@linaro.org> Tested-by: Jami Kettunen <jami.kettunen@somainline.org> Link: https://lore.kernel.org/r/20221024210336.4014983-2-caleb.connolly@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Caleb Connolly [Mon, 24 Oct 2022 21:03:31 +0000 (22:03 +0100)]
net: ipa: fix v3.5.1 resource limit max values
Some resource limits on IPA v3.5.1 have their max values set to
255, this causes a few splats in ipa_reg_encode and prevents the
IPA from booting properly. The limits are all 6 bits wide so
adjust the max values to 63.
Yang Yingliang [Mon, 24 Oct 2022 13:13:38 +0000 (21:13 +0800)]
net: ksz884x: fix missing pci_disable_device() on error in pcidev_init()
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.
Slawomir Laba [Mon, 24 Oct 2022 10:05:26 +0000 (03:05 -0700)]
i40e: Fix flow-type by setting GL_HASH_INSET registers
Fix setting bits for specific flow_type for GLQF_HASH_INSET register.
In previous version all of the bits were set only in hena register, while
in inset only one bit was set. In order for this working correctly on all
types of cards these bits needs to be set correctly for both hena and inset
registers.
Fixes: 2d4d6b475ffb ("i40e: Allow RSS Hash set with less than four parameters") Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
i40e: Fix VF hang when reset is triggered on another VF
When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:
[ +4.890195] iavf 0000:86:02.1: Never saw reset
and VF will hang waiting for the reset to be triggered.
Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.
Fixes: 445c07b3903e ("i40e: add locking around VF reset") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.
Apply a different mask on the register when setting the
RSS hash for the X722 device.
When displaying the flow types enabled via ethtool:
ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6
the driver would print wrong values for X722 device.
Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.
Fixes: 2d4d6b475ffb ("i40e: Allow RSS Hash set with less than four parameters") Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Mon, 24 Oct 2022 02:01:24 +0000 (19:01 -0700)]
ipv6: ensure sane device mtu in tunnels
Another syzbot report [1] with no reproducer hints
at a bug in ip6_gre tunnel (dev:ip6gretap0)
Since ipv6 mcast code makes sure to read dev->mtu once
and applies a sanity check on it (see commit 62f2c3237665
"ipv6: mcast: better catch silly mtu values"), a remaining
possibility is that a layer is able to set dev->mtu to
an underflowed value (high order bit set).
This could happen indeed in ip6gre_tnl_link_config_route(),
ip6_tnl_link_config() and ipip6_tunnel_bind_dev()
Make sure to sanitize mtu value in a local variable before
it is written once on dev->mtu, as lockless readers could
catch wrong temporary value.
RK3588(s) can have multiple gmac controllers.
Re-use rk3568 logic to distinguish them.
Fixes: 581ce35de125 ("net: ethernet: stmmac: dwmac-rk: Add gmac support for rk3588") Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://lore.kernel.org/r/20221021172422.88534-1-sebastian.reichel@collabora.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Dongliang Mu [Mon, 24 Oct 2022 11:48:07 +0000 (19:48 +0800)]
can: mscan: mpc5xxx: mpc5xxx_can_probe(): add missing put_clock() in error path
The commit c85427dfab12 ("can: mscan: improve clock API use") only
adds put_clock() in mpc5xxx_can_remove() function, forgetting to add
put_clock() in the error handling code.
Fix this bug by adding put_clock() in the error handling code.
Jakub Kicinski [Tue, 25 Oct 2022 04:17:02 +0000 (21:17 -0700)]
Merge tag 'ieee802154-for-net-2022-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2022-10-24
Two fixup patches for return code changes of an earlier commit.
Wei Yongjun fixed a missed -EINVAL return on the recent change, while
Alexander Aring adds handling for unknown address type cases as well.
Miquel Raynal fixed a long standing issue with LQI value recording
which got broken 8 years ago. (It got more attention with the work
in progress enhancement in wpan).
* tag 'ieee802154-for-net-2022-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
mac802154: Fix LQI recording
net: ieee802154: fix error return code in dgram_bind()
net: ieee802154: return -EINVAL for unknown addr type
====================
Paolo Abeni [Fri, 21 Oct 2022 22:58:56 +0000 (15:58 -0700)]
mptcp: fix abba deadlock on fastopen
Our CI reported lockdep splat in the fastopen code:
======================================================
WARNING: possible circular locking dependency detected
6.0.0.mptcp_f5e8bfe9878d+ #1558 Not tainted
------------------------------------------------------
packetdrill/1071 is trying to acquire lock: ffff8881bd198140 (sk_lock-AF_INET){+.+.}-{0:0}, at: inet_wait_for_connect+0x19c/0x310
but task is already holding lock: ffff8881b8346540 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0xfdf/0x1740
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
1 lock held by packetdrill/1071:
#0: ffff8881b8346540 (k-sk_lock-AF_INET){+.+.}-{0:0}, at: mptcp_sendmsg+0xfdf/0x1740
======================================================
The problem is caused by the blocking inet_wait_for_connect() releasing
and re-acquiring the msk socket lock while the subflow socket lock is
still held and the MPTCP socket requires that the msk socket lock must
be acquired before the subflow socket lock.
Address the issue always invoking tcp_sendmsg_fastopen() in an
unblocking manner, and later eventually complete the blocking
__inet_stream_connect() as needed.
Fixes: 7a21156d1e6c ("mptcp: handle defer connect in mptcp_sendmsg") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Fri, 21 Oct 2022 22:58:55 +0000 (15:58 -0700)]
mptcp: factor out mptcp_connect()
The current MPTCP connect implementation duplicates a bit of inet
code and does not use nor provide a struct proto->connect callback,
which in turn will not fit the upcoming fastopen implementation.
Refactor such implementation to use the common helper, moving the
MPTCP-specific bits into mptcp_connect(). Additionally, avoid an
indirect call to the subflow connect callback.
Note that the fastopen call-path invokes mptcp_connect() while already
holding the subflow socket lock. Explicitly keep track of such path
via a new MPTCP-level flag and handle the locking accordingly.
Additionally, track the connect flags in a new msk field to allow
propagating them to the subflow inet_stream_connect call.
Fixes: 7a21156d1e6c ("mptcp: handle defer connect in mptcp_sendmsg") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Fri, 21 Oct 2022 22:58:54 +0000 (15:58 -0700)]
mptcp: set msk local address earlier
The mptcp_pm_nl_get_local_id() code assumes that the msk local address
is available at that point. For passive sockets, we initialize such
address at accept() time.
Depending on the running configuration and the user-space timing, a
passive MPJ subflow can join the msk socket before accept() completes.
In such case, the PM assigns a wrong local id to the MPJ subflow
and later PM netlink operations will end-up touching the wrong/unexpected
subflow.
All the above causes sporadic self-tests failures, especially when
the host is heavy loaded.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/308 Fixes: 99f1c40f5b5e ("mptcp: add netlink-based PM") Fixes: be1dae032c5f ("mptcp: introduce implicit endpoints") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur [Fri, 21 Oct 2022 09:07:11 +0000 (11:07 +0200)]
net: lan966x: Stop replacing tx dcbs and dcbs_buf when changing MTU
When a frame is sent using FDMA, the skb is mapped and then the mapped
address is given to an tx dcb that is different than the last used tx
dcb. Once the HW finish with this frame, it would generate an interrupt
and then the dcb can be reused and memory can be freed. For each dcb
there is an dcb buf that contains some meta-data(is used by PTP, is
it free). There is 1 to 1 relationship between dcb and dcb_buf.
The following issue was observed. That sometimes after changing the MTU
to allocate new tx dcbs and dcbs_buf, two frames were not
transmitted. The frames were not transmitted because when reloading the
tx dcbs, it was always presuming to use the first dcb but that was not
always happening. Because it could be that the last tx dcb used before
changing MTU was first dcb and then when it tried to get the next dcb it
would take dcb 1 instead of 0. Because it is supposed to take a
different dcb than the last used one. This can be fixed simply by
changing tx->last_in_use to -1 when the fdma is disabled to reload the
new dcb and dcbs_buff.
But there could be a different issue. For example, right after the frame
is sent, the MTU is changed. Now all the dcbs and dcbs_buf will be
cleared. And now get the interrupt from HW that it finished with the
frame. So when we try to clear the skb, it is not possible because we
lost all the dcbs_buf.
The solution here is to stop replacing the tx dcbs and dcbs_buf when
changing MTU because the TX doesn't care what is the MTU size, it is
only the RX that needs this information.
Jakub Kicinski [Fri, 21 Oct 2022 19:35:32 +0000 (12:35 -0700)]
genetlink: piggy back on resv_op to default to a reject policy
To keep backward compatibility we used to leave attribute parsing
to the family if no policy is specified. This becomes tedious as
we move to more strict validation. Families must define reject all
policies if they don't want any attributes accepted.
Piggy back on the resv_start_op field as the switchover point.
AFAICT only ethtool has added new commands since the resv_start_op
was defined, and it has per-op policies so this should be a no-op.
Nonetheless the patch should still go into v6.1 for consistency.
Linus Torvalds [Mon, 24 Oct 2022 19:43:51 +0000 (12:43 -0700)]
Merge tag 'net-6.1-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf.
The net-memcg fix stands out, the rest is very run-off-the-mill. Maybe
I'm biased.
Current release - regressions:
- eth: fman: re-expose location of the MAC address to userspace,
apparently some udev scripts depended on the exact value
Current release - new code bugs:
- bpf:
- wait for busy refill_work when destroying bpf memory allocator
- allow bpf_user_ringbuf_drain() callbacks to return 1
- fix dispatcher patchable function entry to 5 bytes nop
Previous releases - regressions:
- net-memcg: avoid stalls when under memory pressure
- tcp: fix indefinite deferral of RTO with SACK reneging
- tipc: fix a null-ptr-deref in tipc_topsrv_accept
- eth: macb: specify PHY PM management done by MAC
- tcp: fix a signed-integer-overflow bug in tcp_add_backlog()
Previous releases - always broken:
- eth: amd-xgbe: SFP fixes and compatibility improvements
Misc:
- docs: netdev: offer performance feedback to contributors"
* tag 'net-6.1-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
net-memcg: avoid stalls when under memory pressure
tcp: fix indefinite deferral of RTO with SACK reneging
tcp: fix a signed-integer-overflow bug in tcp_add_backlog()
net: lantiq_etop: don't free skb when returning NETDEV_TX_BUSY
net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed
docs: netdev: offer performance feedback to contributors
kcm: annotate data-races around kcm->rx_wait
kcm: annotate data-races around kcm->rx_psock
net: fman: Use physical address for userspace interfaces
net/mlx5e: Cleanup MACsec uninitialization routine
atlantic: fix deadlock at aq_nic_stop
nfp: only clean `sp_indiff` when application firmware is unloaded
amd-xgbe: add the bit rate quirk for Molex cables
amd-xgbe: fix the SFP compliance codes check for DAC cables
amd-xgbe: enable PLL_CTL for fixed PHY modes only
amd-xgbe: use enums for mailbox cmd and sub_cmds
amd-xgbe: Yellow carp devices do not need rrc
bpf: Use __llist_del_all() whenever possbile during memory draining
bpf: Wait for busy refill_work when destroying bpf memory allocator
MAINTAINERS: add keyword match on PTP
...
Linus Torvalds [Mon, 24 Oct 2022 19:33:30 +0000 (12:33 -0700)]
Merge tag 'rcu-urgent.2022.10.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull RCU fix from Paul McKenney:
"Fix a regression caused by commit 64f714130887 ("rcu: Switch polled
grace-period APIs to ->gp_seq_polled"), which could incorrectly leave
interrupts enabled after an early-boot call to synchronize_rcu().
Such synchronize_rcu() calls must acquire leaf rcu_node locks in order
to properly interact with polled grace periods, but the code did not
take into account the possibility of synchronize_rcu() being invoked
from the portion of the boot sequence during which interrupts are
disabled.
This commit therefore switches the lock acquisition and release from
irq to irqsave/irqrestore"
* tag 'rcu-urgent.2022.10.20a' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
rcu: Keep synchronize_rcu() from enabling irqs in early boot
Linus Torvalds [Mon, 24 Oct 2022 19:19:34 +0000 (12:19 -0700)]
Merge tag 'linux-kselftest-kunit-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"One single fix to update alloc_string_stream() callers to check for
IS_ERR() instead of NULL to be in sync with alloc_string_stream()
returning an ERR_PTR()"
* tag 'linux-kselftest-kunit-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: update NULL vs IS_ERR() tests
Linus Torvalds [Mon, 24 Oct 2022 19:10:55 +0000 (12:10 -0700)]
Merge tag 'linux-kselftest-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- futex, intel_pstate, kexec build fixes
- ftrace dynamic_events dependency check fix
- memory-hotplug fix to remove redundant warning from test report
* tag 'linux-kselftest-fixes-6.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/ftrace: fix dynamic_events dependency check
selftests/memory-hotplug: Remove the redundant warning information
selftests/kexec: fix build for ARCH=x86_64
selftests/intel_pstate: fix build for ARCH=x86_64
selftests/futex: fix build for clang
Linus Torvalds [Mon, 24 Oct 2022 18:48:30 +0000 (11:48 -0700)]
Merge tag 'pinctrl-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix typos in UART1 and MMC in the Ingenic driver
- A really well researched glitch bug fix to the Qualcomm driver that
was tracked down and fixed by Dough Anderson from Chromium. Hats off
for this one!
- Revert two patches on the Xilinx ZynqMP driver: this needs a proper
solution making use of firmware version information to adapt to
different firmware releases
- Fix interrupt triggers in the Ocelot driver
* tag 'pinctrl-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: ocelot: Fix incorrect trigger of the interrupt.
Revert "dt-bindings: pinctrl-zynqmp: Add output-enable configuration"
Revert "pinctrl: pinctrl-zynqmp: Add support for output-enable and bias-high-impedance"
pinctrl: qcom: Avoid glitching lines when we first mux to output
pinctrl: Ingenic: JZ4755 bug fixes
Jakub Kicinski [Fri, 21 Oct 2022 16:03:04 +0000 (09:03 -0700)]
net-memcg: avoid stalls when under memory pressure
As Shakeel explains the commit under Fixes had the unintended
side-effect of no longer pre-loading the cached memory allowance.
Even tho we previously dropped the first packet received when
over memory limit - the consecutive ones would get thru by using
the cache. The charging was happening in batches of 128kB, so
we'd let in 128kB (truesize) worth of packets per one drop.
After the change we no longer force charge, there will be no
cache filling side effects. This causes significant drops and
connection stalls for workloads which use a lot of page cache,
since we can't reclaim page cache under GFP_NOWAIT.
Some of the latency can be recovered by improving SACK reneg
handling but nowhere near enough to get back to the pre-5.15
performance (the application I'm experimenting with still
sees 5-10x worst latency).
Apply the suggested workaround of using GFP_ATOMIC. We will now
be more permissive than previously as we'll drop _no_ packets
in softirq when under pressure. But I can't think of any good
and simple way to address that within networking.
Neal Cardwell [Fri, 21 Oct 2022 17:08:21 +0000 (17:08 +0000)]
tcp: fix indefinite deferral of RTO with SACK reneging
This commit fixes a bug that can cause a TCP data sender to repeatedly
defer RTOs when encountering SACK reneging.
The bug is that when we're in fast recovery in a scenario with SACK
reneging, every time we get an ACK we call tcp_check_sack_reneging()
and it can note the apparent SACK reneging and rearm the RTO timer for
srtt/2 into the future. In some SACK reneging scenarios that can
happen repeatedly until the receive window fills up, at which point
the sender can't send any more, the ACKs stop arriving, and the RTO
fires at srtt/2 after the last ACK. But that can take far too long
(O(10 secs)), since the connection is stuck in fast recovery with a
low cwnd that cannot grow beyond ssthresh, even if more bandwidth is
available.
This fix changes the logic in tcp_check_sack_reneging() to only rearm
the RTO timer if data is cumulatively ACKed, indicating forward
progress. This avoids this kind of nearly infinite loop of RTO timer
re-arming. In addition, this meets the goals of
tcp_check_sack_reneging() in handling Windows TCP behavior that looks
temporarily like SACK reneging but is not really.
Many thanks to Jakub Kicinski and Neil Spring, who reported this issue
and provided critical packet traces that enabled root-causing this
issue. Also, many thanks to Jakub Kicinski for testing this fix.
Fixes: ad64ae592e48 ("tcp: reduce spurious retransmits due to transient SACK reneging") Reported-by: Jakub Kicinski <kuba@kernel.org> Reported-by: Neil Spring <ntspring@fb.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Tested-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/r/20221021170821.1093930-1-ncardwell.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 24 Oct 2022 17:32:00 +0000 (10:32 -0700)]
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Alexei Starovoitov says:
====================
pull-request: bpf 2022-10-23
We've added 7 non-merge commits during the last 18 day(s) which contain
a total of 8 files changed, 69 insertions(+), 5 deletions(-).
The main changes are:
1) Wait for busy refill_work when destroying bpf memory allocator, from Hou.
2) Allow bpf_user_ringbuf_drain() callbacks to return 1, from David.
3) Fix dispatcher patchable function entry to 5 bytes nop, from Jiri.
4) Prevent decl_tag from being referenced in func_proto, from Stanislav.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Use __llist_del_all() whenever possbile during memory draining
bpf: Wait for busy refill_work when destroying bpf memory allocator
bpf: Fix dispatcher patchable function entry to 5 bytes nop
bpf: prevent decl_tag from being referenced in func_proto
selftests/bpf: Add reproducer for decl_tag in func_proto return type
selftests/bpf: Make bpf_user_ringbuf_drain() selftest callback return 1
bpf: Allow bpf_user_ringbuf_drain() callbacks to return 1
====================
Lu Wei [Fri, 21 Oct 2022 04:06:22 +0000 (12:06 +0800)]
tcp: fix a signed-integer-overflow bug in tcp_add_backlog()
The type of sk_rcvbuf and sk_sndbuf in struct sock is int, and
in tcp_add_backlog(), the variable limit is caculated by adding
sk_rcvbuf, sk_sndbuf and 64 * 1024, it may exceed the max value
of int and overflow. This patch reduces the limit budget by
halving the sndbuf to solve this issue since ACK packets are much
smaller than the payload.
Fixes: 9904ee5a0fdf ("tcp: add tcp_add_backlog()") Signed-off-by: Lu Wei <luwei32@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao [Thu, 20 Oct 2022 02:42:13 +0000 (10:42 +0800)]
net: fix UAF issue in nfqnl_nf_hook_drop() when ops_init() failed
When the ops_init() interface is invoked to initialize the net, but
ops->init() fails, data is released. However, the ptr pointer in
net->gen is invalid. In this case, when nfqnl_nf_hook_drop() is invoked
to release the net, invalid address access occurs.
The process is as follows:
setup_net()
ops_init()
data = kzalloc(...) ---> alloc "data"
net_assign_generic() ---> assign "date" to ptr in net->gen
...
ops->init() ---> failed
...
kfree(data); ---> ptr in net->gen is invalid
...
ops_exit_list()
...
nfqnl_nf_hook_drop()
*q = nfnl_queue_pernet(net) ---> q is invalid
The following is the Call Trace information:
BUG: KASAN: use-after-free in nfqnl_nf_hook_drop+0x264/0x280
Read of size 8 at addr ffff88810396b240 by task ip/15855
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
print_report+0x155/0x454
kasan_report+0xba/0x1f0
nfqnl_nf_hook_drop+0x264/0x280
nf_queue_nf_hook_drop+0x8b/0x1b0
__nf_unregister_net_hook+0x1ae/0x5a0
nf_unregister_net_hooks+0xde/0x130
ops_exit_list+0xb0/0x170
setup_net+0x7ac/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
Fixes: d663129d2c6f ("net: Automatically allocate per namespace data.") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 20 Oct 2022 18:30:31 +0000 (11:30 -0700)]
docs: netdev: offer performance feedback to contributors
Some of us gotten used to producing large quantities of peer feedback
at work, every 3 or 6 months. Extending the same courtesy to community
members seems like a logical step. It may be hard for some folks to
get validation of how important their work is internally, especially
at smaller companies which don't employ many kernel experts.
The concept of "peer feedback" may be a hyperscaler / silicon valley
thing so YMMV. Hopefully we can build more context as we go.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 17869 Comm: syz-executor.2 Not tainted 6.1.0-rc1-syzkaller-00010-gbb1a1146467a-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
Fixes: 01e0164f6208 ("kcm: Kernel Connection Multiplexor module") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
value changed: 0xffff88812971ce00 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 5859 Comm: syz-executor.3 Not tainted 6.0.0-syzkaller-12189-g19d17ab7c68b-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
Fixes: 01e0164f6208 ("kcm: Kernel Connection Multiplexor module") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sean Anderson [Thu, 20 Oct 2022 15:50:41 +0000 (11:50 -0400)]
net: fman: Use physical address for userspace interfaces
Before 67e6118c37b7 ("net: fman: Map the base address once"), the
physical address of the MAC was exposed to userspace in two places: via
sysfs and via SIOCGIFMAP. While this is not best practice, it is an
external ABI which is in use by userspace software.
The aforementioned commit inadvertently modified these addresses and
made them virtual. This constitutes and ABI break. Additionally, it
leaks the kernel's memory layout to userspace. Partially revert that
commit, reintroducing the resource back into struct mac_device, while
keeping the intended changes (the rework of the address mapping).
Fixes: 67e6118c37b7 ("net: fman: Map the base address once") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Sean Anderson <sean.anderson@seco.com> Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5e_macsec_cleanup() routine has NULL pointer dereferencing if mlx5
device doesn't support MACsec (priv->macsec will be NULL).
While at it delete comment line, assignment and extra blank lines, so fix
everything in one patch.
Fixes: 166a0c23fe87 ("net/mlx5e: Create advanced steering operation (ASO) object for MACsec") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Íñigo Huguet [Thu, 20 Oct 2022 07:53:10 +0000 (09:53 +0200)]
atlantic: fix deadlock at aq_nic_stop
NIC is stopped with rtnl_lock held, and during the stop it cancels the
'service_task' work and free irqs.
However, if CONFIG_MACSEC is set, rtnl_lock is acquired both from
aq_nic_service_task and aq_linkstate_threaded_isr. Then a deadlock
happens if aq_nic_stop tries to cancel/disable them when they've already
started their execution.
As the deadlock is caused by rtnl_lock, it causes many other processes
to stall, not only atlantic related stuff.
Fix it by introducing a mutex that protects each NIC's macsec related
data, and locking it instead of the rtnl_lock from the service task and
the threaded IRQ.
Before this patch, all macsec data was protected with rtnl_lock, but
maybe not all of it needs to be protected. With this new mutex, further
efforts can be made to limit the protected data only to that which
requires it. However, probably it doesn't worth it because all macsec's
data accesses are infrequent, and almost all are done from macsec_ops
or ethtool callbacks, called holding rtnl_lock, so macsec_mutex won't
never be much contended.
The issue appeared repeteadly attaching and deattaching the NIC to a
bond interface. Doing that after this patch I cannot reproduce the bug.
Fixes: 1783526231b4 ("net: atlantic: MACSec offload skeleton") Reported-by: Li Liang <liali@redhat.com> Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Íñigo Huguet <ihuguet@redhat.com> Reviewed-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Miquel Raynal [Thu, 20 Oct 2022 14:25:35 +0000 (16:25 +0200)]
mac802154: Fix LQI recording
Back in 2014, the LQI was saved in the skb control buffer (skb->cb, or
mac_cb(skb)) without any actual reset of this area prior to its use.
As part of a useful rework of the use of this region, 5fec0c3339de
("ieee802154: change _cb handling slightly") introduced mac_cb_init() to
basically memset the cb field to 0. In particular, this new function got
called at the beginning of mac802154_parse_frame_start(), right before
the location where the buffer got actually filled.
What went through unnoticed however, is the fact that the very first
helper called by device drivers in the receive path already used this
area to save the LQI value for later extraction. Resetting the cb field
"so late" led to systematically zeroing the LQI.
If we consider the reset of the cb field needed, we can make it as soon
as we get an skb from a device driver, right before storing the LQI,
as is the very first time we need to write something there.
Linus Torvalds [Sun, 23 Oct 2022 22:00:43 +0000 (15:00 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"RISC-V:
- Fix compilation without RISCV_ISA_ZICBOM
- Fix kvm_riscv_vcpu_timer_pending() for Sstc
ARM:
- Fix a bug preventing restoring an ITS containing mappings for very
large and very sparse device topology
- Work around a relocation handling error when compiling the nVHE
object with profile optimisation
- Fix for stage-2 invalidation holding the VM MMU lock for too long
by limiting the walk to the largest block mapping size
- Enable stack protection and branch profiling for VHE
- Two selftest fixes
x86:
- add compat implementation for KVM_X86_SET_MSR_FILTER ioctl
selftests:
- synchronize includes between include/uapi and tools/include/uapi"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
tools: include: sync include/api/linux/kvm.h
KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
KVM: x86: Copy filter arg outside kvm_vm_ioctl_set_msr_filter()
kvm: Add support for arch compat vm ioctls
RISC-V: KVM: Fix kvm_riscv_vcpu_timer_pending() for Sstc
RISC-V: Fix compilation without RISCV_ISA_ZICBOM
KVM: arm64: vgic: Fix exit condition in scan_its_table()
KVM: arm64: nvhe: Fix build with profile optimization
KVM: selftests: Fix number of pages for memory slot in memslot_modification_stress_test
KVM: arm64: selftests: Fix multiple versions of GIC creation
KVM: arm64: Enable stack protection and branch profiling for VHE
KVM: arm64: Limit stage2_apply_range() batch size to largest block
KVM: arm64: Work out supported block level at compile time
It broke reboots on big-endian MIPS and MIPS64 malta QEMU instances,
which use the syscon driver. Little-endian is not effected, which means
likely it's important to handle regmap_get_val_endian() in this function
after all.
Fixes: 9faa7df5463a ("mfd: syscon: Remove repetition of the regmap_get_val_endian()") Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Lee Jones <lee@kernel.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 23 Oct 2022 19:01:01 +0000 (12:01 -0700)]
kernel/utsname_sysctl.c: Fix hostname polling
Commit 78f1610ca0b3 ("kernel/utsname_sysctl.c: print kernel arch") added
a new entry to the uts_kern_table[] array, but didn't update the
UTS_PROC_xyz enumerators of older entries, breaking anything that used
them.
Which is admittedly not many cases: it's really just the two uses of
uts_proc_notify() in kernel/sys.c. But apparently journald-systemd
actually uses this to detect hostname changes.
Linus Torvalds [Sun, 23 Oct 2022 17:14:45 +0000 (10:14 -0700)]
Merge tag 'perf_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Fix raw data handling when perf events are used in bpf
- Rework how SIGTRAPs get delivered to events to address a bunch of
problems with it. Add a selftest for that too
* tag 'perf_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bpf: Fix sample_flags for bpf_perf_event_output
selftests/perf_events: Add a SIGTRAP stress test with disables
perf: Fix missing SIGTRAPs
Linus Torvalds [Sun, 23 Oct 2022 17:10:55 +0000 (10:10 -0700)]
Merge tag 'sched_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Adjust code to not trip up CFI
- Fix sched group cookie matching
* tag 'sched_urgent_for_v6.1_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Introduce struct balance_callback to avoid CFI mismatches
sched/core: Fix comparison in sched_group_cookie_match()
Linus Torvalds [Sun, 23 Oct 2022 17:01:34 +0000 (10:01 -0700)]
Merge tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
"As usually the case, right after a major release, the tip urgent
branches accumulate a couple more fixes than normal. And here is the
x86, a bit bigger, urgent pile.
- Use the correct CPU capability clearing function on the error path
in Intel perf LBR
- A CFI fix to ftrace along with a simplification
- Adjust handling of zero capacity bit mask for resctrl cache
allocation on AMD
- A fix to the AMD microcode loader to attempt patch application on
every logical thread
- A couple of topology fixes to handle CPUID leaf 0x1f enumeration
info properly
- Drop a -mabi=ms compiler option check as both compilers support it
now anyway
- A couple of fixes to how the initial, statically allocated FPU
buffer state is setup and its interaction with dynamic states at
runtime"
* tag 'x86_urgent_for_v6.0_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Fix copy_xstate_to_uabi() to copy init states correctly
perf/x86/intel/lbr: Use setup_clear_cpu_cap() instead of clear_cpu_cap()
ftrace,kcfi: Separate ftrace_stub() and ftrace_stub_graph()
x86/ftrace: Remove ftrace_epilogue()
x86/resctrl: Fix min_cbm_bits for AMD
x86/microcode/AMD: Apply the patch early on every logical thread
x86/topology: Fix duplicated core ID within a package
x86/topology: Fix multiple packages shown on a single-package system
hwmon/coretemp: Handle large core ID value
x86/Kconfig: Drop check for -mabi=ms for CONFIG_EFI_STUB
x86/fpu: Exclude dynamic states from init_fpstate
x86/fpu: Fix the init_fpstate size check with the actual size
x86/fpu: Configure init_fpstate attributes orderly
Linus Torvalds [Sun, 23 Oct 2022 16:55:50 +0000 (09:55 -0700)]
Merge tag 'io_uring-6.1-2022-10-22' of git://git.kernel.dk/linux
Pull io_uring follow-up from Jens Axboe:
"Currently the zero-copy has automatic fallback to normal transmit, and
it was decided that it'd be cleaner to return an error instead if the
socket type doesn't support it.
Zero-copy does work with UDP and TCP, it's more of a future proofing
kind of thing (eg for samba)"
* tag 'io_uring-6.1-2022-10-22' of git://git.kernel.dk/linux:
io_uring/net: fail zc sendmsg when unsupported by socket
io_uring/net: fail zc send when unsupported by socket
net: flag sockets supporting msghdr originated zerocopy
Linus Torvalds [Sat, 22 Oct 2022 23:04:34 +0000 (16:04 -0700)]
Merge tag 'hwmon-for-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- corsair-psu: Fix typo in USB id description, and add USB ID for new
PSU
- pwm-fan: Fix fan power handling when disabling fan control
* tag 'hwmon-for-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (corsair-psu) Add USB id of the new HX1500i psu
hwmon: (pwm-fan) Explicitly switch off fan power when setting pwm1_enable to 0
hwmon: (corsair-psu) fix typo in USB id description
Linus Torvalds [Sat, 22 Oct 2022 22:59:46 +0000 (15:59 -0700)]
Merge tag 'i2c-for-6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"RPM fix for qcom-cci, platform module alias for xiic, build warning
fix for mlxbf, typo fixes in comments"
* tag 'i2c-for-6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mlxbf: depend on ACPI; clean away ifdeffage
i2c: fix spelling typos in comments
i2c: qcom-cci: Fix ordering of pm_runtime_xx and i2c_add_adapter
i2c: xiic: Add platform module alias
Linus Torvalds [Sat, 22 Oct 2022 22:52:36 +0000 (15:52 -0700)]
Merge tag 'pci-v6.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fixes from Bjorn Helgaas:
- Revert a simplification that broke pci-tegra due to a masking error
- Update MAINTAINERS for Kishon's email address change and TI
DRA7XX/J721E maintainer change
* tag 'pci-v6.1-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Kishon's email address in PCI endpoint subsystem
MAINTAINERS: Add Vignesh Raghavendra as maintainer of TI DRA7XX/J721E PCI driver
Revert "PCI: tegra: Use PCI_CONF1_EXT_ADDRESS() macro"
Linus Torvalds [Sat, 22 Oct 2022 22:30:15 +0000 (15:30 -0700)]
Merge tag 'media/v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull missed media updates from Mauro Carvalho Chehab:
"It seems I screwed-up my previous pull request: it ends up that only
half of the media patches that were in linux-next got merged in -rc1.
The script which creates the signed tags silently failed due to
5.19->6.0 so it ended generating a tag with incomplete stuff.
So here are the missing parts:
- a DVB core security fix
- lots of fixes and cleanups for atomisp staging driver
- old drivers that are VB1 are being moved to staging to be
deprecated
- several driver updates - mostly for embedded systems, but there are
also some things addressing issues with some PC webcams, in the UVC
video driver"
* tag 'media/v6.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (163 commits)
media: sun6i-csi: Move csi buffer definition to main header file
media: sun6i-csi: Introduce and use video helper functions
media: sun6i-csi: Add media ops with link notify callback
media: sun6i-csi: Remove controls handler from the driver
media: sun6i-csi: Register the media device after creation
media: sun6i-csi: Pass and store csi device directly in video code
media: sun6i-csi: Tidy up video code
media: sun6i-csi: Tidy up v4l2 code
media: sun6i-csi: Tidy up Kconfig
media: sun6i-csi: Use runtime pm for clocks and reset
media: sun6i-csi: Define and use variant to get module clock rate
media: sun6i-csi: Always set exclusive module clock rate
media: sun6i-csi: Tidy up platform code
media: sun6i-csi: Refactor main driver data structures
media: sun6i-csi: Define and use driver name and (reworked) description
media: cedrus: Add a Kconfig dependency on RESET_CONTROLLER
media: sun8i-rotate: Add a Kconfig dependency on RESET_CONTROLLER
media: sun8i-di: Add a Kconfig dependency on RESET_CONTROLLER
media: sun4i-csi: Add a Kconfig dependency on RESET_CONTROLLER
media: sun6i-csi: Add a Kconfig dependency on RESET_CONTROLLER
...
Pavel Begunkov [Fri, 21 Oct 2022 10:16:40 +0000 (11:16 +0100)]
io_uring/net: fail zc send when unsupported by socket
If a protocol doesn't support zerocopy it will silently fall back to
copying. This type of behaviour has always been a source of troubles
so it's better to fail such requests instead.
Pavel Begunkov [Fri, 21 Oct 2022 10:16:39 +0000 (11:16 +0100)]
net: flag sockets supporting msghdr originated zerocopy
We need an efficient way in io_uring to check whether a socket supports
zerocopy with msghdr provided ubuf_info. Add a new flag into the struct
socket flags fields.
Alexander Graf [Mon, 17 Oct 2022 18:45:41 +0000 (20:45 +0200)]
KVM: x86: Add compat handler for KVM_X86_SET_MSR_FILTER
The KVM_X86_SET_MSR_FILTER ioctls contains a pointer in the passed in
struct which means it has a different struct size depending on whether
it gets called from 32bit or 64bit code.
This patch introduces compat code that converts from the 32bit struct to
its 64bit counterpart which then gets used going forward internally.
With this applied, 32bit QEMU can successfully set MSR bitmaps when
running on 64bit kernels.
Reported-by: Andrew Randrianasulu <randrianasulu@gmail.com> Fixes: 61513ecbd8621 ("KVM: x86: Introduce MSR filtering") Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <20221017184541.2658-4-graf@amazon.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the next patch we want to introduce a second caller to
set_msr_filter() which constructs its own filter list on the stack.
Refactor the original function so it takes it as argument instead of
reading it through copy_from_user().
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <20221017184541.2658-3-graf@amazon.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Alexander Graf [Mon, 17 Oct 2022 18:45:39 +0000 (20:45 +0200)]
kvm: Add support for arch compat vm ioctls
We will introduce the first architecture specific compat vm ioctl in the
next patch. Add all necessary boilerplate to allow architectures to
override compat vm ioctls when necessary.
Signed-off-by: Alexander Graf <graf@amazon.com>
Message-Id: <20221017184541.2658-2-graf@amazon.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yinjun Zhang [Thu, 20 Oct 2022 08:14:11 +0000 (09:14 +0100)]
nfp: only clean `sp_indiff` when application firmware is unloaded
Currently `sp_indiff` is cleaned when driver is removed. This will
cause problem in multi-PF/multi-host case, considering one PF is
removed while another is still in use.
Since `sp_indiff` is the application firmware property, it should
only be cleaned when the firmware is unloaded. Now let management
firmware to clean it when necessary, driver only set it.
Fixes: 31cd3ebc1638 ("nfp: refine the ABI of getting `sp_indiff` info") Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20221020081411.80186-1-simon.horman@corigine.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
(1) Fix the rrc for Yellow carp devices. CDR workaround path
is disabled for YC devices, receiver reset cycle is not
needed in such cases.
(2) Add enumerations for mailbox command and sub-commands.
Instead of using hard-coded values, use enums.
(3) Enable PLL_CTL for fixed PHY modes only. Driver does not
implement SW RRCM for Autoneg Off configuration, hence PLL
is needed for fixed PHY modes only.
(4) Fix the SFP compliance codes check for DAC cables. Some of
the passive cables have non-zero data at offset 6 in
SFP EEPROM data. So, fix the sfp compliance codes check.
(5) Add a quirk for Molex passive cables to extend the rate
ceiling to 0x78.
====================
Raju Rangoju [Thu, 20 Oct 2022 06:42:15 +0000 (12:12 +0530)]
amd-xgbe: add the bit rate quirk for Molex cables
The offset 12 (bit-rate) of EEPROM SFP DAC (passive) cables is expected
to be in the range 0x64 to 0x68. However, the 5 meter and 7 meter Molex
passive cables have the rate ceiling 0x78 at offset 12.
Add a quirk for Molex passive cables to extend the rate ceiling to 0x78.
Fixes: b4e904b9c76f ("amd-xgbe: Add support for SFP+ modules") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / kernel.git / log