Although XOR hash function can perform very well on some special use
cases, to align with all drivers, mlx5 driver should use Toeplitz hash
by default.
Toeplitz is more stable for the general use case and it is more standard
and reliable.
On top of that, since XOR (MLX5_RX_HASH_FN_INVERTED_XOR8) gives only a
repeated 8 bits pattern. When used for udp tunneling RSS source port
manipulation it results in fixed source port, which will cause bad RSS
spread.
Prior the commit we are reverting, checksum unnecessary was only set when
both the L3 OK and L4 OK bits are set on the CQE. This caused packets
of IP protocols such as SCTP which are not dealt by the current HW L4
parser (hence the L4 OK bit is not set, but the L4 header type none bit
is set) to go through the checksum none code, where currently we wrongly
report checksum unnecessary for them, a regression. Fix this by a revert.
Note that on our usual track we report checksum complete, so the revert
isn't expected to have any notable performance impact. Also, when we are
not on the checksum complete track, the L4 protocols for which we report
checksum none are not high performance ones, we will still report
checksum unnecessary for UDP/TCP.
Fixes: 7868234539c6 ("net/mlx5e: Enable reporting checksum unnecessary also for L3 packets") Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Avi Urman <aviu@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Tue, 26 Mar 2019 05:10:59 +0000 (22:10 -0700)]
net/mlx5e: Rx, Check ip headers sanity
In the two places is_last_ethertype_ip is being called, the caller will
be looking inside the ip header, to be safe, add ip{4,6} header sanity
check. And return true only on valid ip headers, i.e: the whole header
is contained in the linear part of the skb.
Note: Such situation is very rare and hard to reproduce, since mlx5e
allocates a large enough headroom to contain the largest header one can
imagine.
Fixes: 575c4738bc77 ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets") Reported-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Tue, 12 Mar 2019 07:24:52 +0000 (00:24 -0700)]
net/mlx5e: Rx, Fixup skb checksum for packets with tail padding
When an ethernet frame with ip payload is padded, the padding octets are
not covered by the hardware checksum.
Prior to the cited commit, skb checksum was forced to be CHECKSUM_NONE
when padding is detected. After it, the kernel will try to trim the
padding bytes and subtract their checksum from skb->csum.
In this patch we fixup skb->csum for any ip packet with tail padding of
any size, if any padding found.
FCS case is just one special case of this general purpose patch, hence,
it is removed.
Fixes: 7943627623eb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"), Cc: Eric Dumazet <edumazet@google.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eran Ben Elisha [Thu, 28 Mar 2019 12:26:47 +0000 (14:26 +0200)]
net/mlx5e: Use fail-safe channels reopen in tx reporter recover
When requested to recover from error, the tx reporter might open new
channels and close the existing ones. Use safe channels switch flow in
order to guarantee opened channels at the end of the recover flow.
For this purpose, define mlx5e_safe_reopen_channels function and use it
within those flows.
Fixes: f9154a205e65 ("net/mlx5e: Add tx reporter support") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eran Ben Elisha [Thu, 28 Mar 2019 08:00:35 +0000 (10:00 +0200)]
net/mlx5e: Skip un-needed tx recover if interface state is down
Skip recover operation if interface is in down state as TX objects are
not open. This fixes a bug were the recover flow re-opened TX objects
which were not opened before, leading to a possible memory leak at
driver unload.
Fixes: f9154a205e65 ("net/mlx5e: Add tx reporter support") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Tue, 19 Mar 2019 08:05:41 +0000 (01:05 -0700)]
net/mlx5: FPGA, tls, idr remove on flow delete
Flow is kfreed on mlx5_fpga_tls_del_flow but kept in the idr data
structure, this is risky and can cause use-after-free, since the
idr_remove is delayed until tls_send_teardown_cmd completion.
Instead of delaying idr_remove, in this patch we do it on
mlx5_fpga_tls_del_flow, before actually kfree(flow).
David S. Miller [Tue, 9 Apr 2019 17:57:10 +0000 (10:57 -0700)]
Merge tag 'mac80211-for-davem-2019-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes:
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211: Honor SW_CRYPTO_CONTROL for unicast keys in AP VLAN mode
Restore SW_CRYPTO_CONTROL operation on AP_VLAN interfaces for unicast
keys, the original override was intended to be done for group keys as
those are treated specially by mac80211 and would always have been
rejected.
Now the situation is that AP_VLAN support must be enabled by the driver
if it can support it (meaning it can support software crypto GTK TX).
Thus, also simplify the code - if we get here with AP_VLAN and non-
pairwise key, software crypto must be used (driver doesn't know about
the interface) and can be used (driver must've advertised AP_VLAN if
it also uses SW_CRYPTO_CONTROL).
Fixes: 7dcff8ac8291 ("mac80211: allow AP_VLAN operation on crypto controlled devices") Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[rewrite commit message] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) Off by one and bounds checking fixes in NFC, from Dan Carpenter.
2) There have been many weird regressions in r8169 since we turned ASPM
support on, some are still not understood nor completely resolved.
Let's turn this back off for now. From Heiner Kallweit.
3) Signess fixes for ethtool speed value handling, from Michael
Zhivich.
4) Handle timestamps properly in macb driver, from Paul Thomas.
5) Two erspan fixes, it's the usual "skb ->data potentially reallocated
and we're holding a stale protocol header pointer". From Lorenzo
Bianconi.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
bnxt_en: Reset device on RX buffer errors.
bnxt_en: Improve RX consumer index validity check.
net: macb driver, check for SKBTX_HW_TSTAMP
qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
net: ip_gre: fix possible use-after-free in erspan_rcv
r8169: disable ASPM again
MAINTAINERS: ieee802154: update documentation file pattern
net: vrf: Fix ping failed when vrf mtu is set to 0
selftests: add a tc matchall test case
nfc: nci: Potential off by one in ->pipes[] array
NFC: nci: Add some bounds checking in nci_hci_cmd_received()
Merge branch 'fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull TPM fixes from James Morris:
"From Jarkko: These are critical fixes for v5.1. Contains also couple
of new selftests for v5.1 features (partial reads in /dev/tpm0)"
* 'fixes-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selftests/tpm2: Open tpm dev in unbuffered mode
selftests/tpm2: Extend tests to cover partial reads
KEYS: trusted: fix -Wvarags warning
tpm: Fix the type of the return value in calc_tpm2_event_size()
KEYS: trusted: allow trusted.ko to initialize w/o a TPM
tpm: fix an invalid condition in tpm_common_poll
tpm: turn on TPM on suspend for TPM 1.x
Merge tag 'xtensa-20190408' of git://github.com/jcmvbkbc/linux-xtensa
Pull xtensa fixes from Max Filippov:
- fix syscall number passed to trace_sys_exit
- fix syscall number initialization in start_thread
- fix level interpretation in the return_address
- fix format string warning in init_pmd
* tag 'xtensa-20190408' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: fix format string warning in init_pmd
xtensa: fix return_address
xtensa: fix initialization of pt_regs::syscall in start_thread
xtensa: use actual syscall number in do_syscall_trace_leave
David S. Miller [Mon, 8 Apr 2019 23:39:41 +0000 (16:39 -0700)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: 2 bug fixes.
The first patch prevents possible driver crash if we get a bad RX index
from the hardware. The second patch resets the device when the hardware
reports buffer error to recover from the error.
Please queue these for -stable also. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 8 Apr 2019 21:39:55 +0000 (17:39 -0400)]
bnxt_en: Reset device on RX buffer errors.
If the RX completion indicates RX buffers errors, the RX ring will be
disabled by firmware and no packets will be received on that ring from
that point on. Recover by resetting the device.
Fixes: 93658deae41f ("bnxt_en: New Broadcom ethernet driver.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 8 Apr 2019 21:39:54 +0000 (17:39 -0400)]
bnxt_en: Improve RX consumer index validity check.
There is logic to check that the RX/TPA consumer index is the expected
index to work around a hardware problem. However, the potentially bad
consumer index is first used to index into an array to reference an entry.
This can potentially crash if the bad consumer index is beyond legal
range. Improve the logic to use the consumer index for dereferencing
after the validity check and log an error message.
Fixes: 142b0d0984db ("bnxt_en: Add workaround to detect bad opaque in rx completion (part 2)") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Thomas [Mon, 8 Apr 2019 19:37:54 +0000 (15:37 -0400)]
net: macb driver, check for SKBTX_HW_TSTAMP
Make sure SKBTX_HW_TSTAMP (i.e. SOF_TIMESTAMPING_TX_HARDWARE) has been
enabled for this skb. It does fix the issue where normal socks that
aren't expecting a timestamp will not wake up on select, but when a
user does want a SOF_TIMESTAMPING_TX_HARDWARE it does work.
Signed-off-by: Paul Thomas <pthomas8589@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
ethtool: fix use of SPEED_UNKNOWN constant
This patch series addresses 2 related issues:
1. ethtool_validate_speed() triggers a "signed-unsigned comparison"
warning due to type difference of SPEED_UNKNOWN constant (int)
and argument to ethtool_validate_speed (__u32).
2. some drivers use u16 storage for SPEED_UNKNOWN constant,
resulting in value truncation and thus failure to test against
SPEED_UNKNOWN correctly.
This revised series addresses several feedback comments:
- split up the patch in to series
- do not unnecessarily change drivers that use "int" storage
for speed values
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Zhivich [Mon, 8 Apr 2019 14:48:47 +0000 (10:48 -0400)]
qlogic: qlcnic: fix use of SPEED_UNKNOWN ethtool constant
qlcnic driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Zhivich [Mon, 8 Apr 2019 14:48:46 +0000 (10:48 -0400)]
broadcom: tg3: fix use of SPEED_UNKNOWN ethtool constant
tg3 driver uses u16 to store SPEED_UKNOWN ethtool constant,
which is defined as -1, resulting in value truncation and
thus incorrect test results against SPEED_UNKNOWN.
For example, the following test will print "False":
u16 speed = SPEED_UNKNOWN;
if (speed == SPEED_UNKNOWN)
printf("True");
else
printf("False");
Change storage of speed to use u32 to avoid this issue.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Zhivich [Mon, 8 Apr 2019 14:48:45 +0000 (10:48 -0400)]
ethtool: avoid signed-unsigned comparison in ethtool_validate_speed()
When building C++ userspace code that includes ethtool.h
with "-Werror -Wall", g++ complains about signed-unsigned comparison in
ethtool_validate_speed() due to definition of SPEED_UNKNOWN as -1.
Explicitly cast SPEED_UNKNOWN to __u32 to match type of
ethtool_validate_speed() argument.
Signed-off-by: Michael Zhivich <mzhivich@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 8 Apr 2019 23:16:47 +0000 (16:16 -0700)]
Merge branch 'erspan-use-after-free'
Lorenzo Bianconi says:
====================
fix possible use-after-free in erspan_v{4,6}
Similar to what I did in commit 4ee718583812 ("ipv6: sit: reset ip
header pointer in ipip6_rcv"), fix possible use-after-free in
erspan_rcv and ip6erspan_rcv extracting tunnel metadata since the
packet can be 'uncloned' running __iptunnel_pull_header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: ip6_gre: fix possible use-after-free in ip6erspan_rcv
erspan_v6 tunnels run __iptunnel_pull_header on received skbs to remove
erspan header. This can determine a possible use-after-free accessing
pkt_md pointer in ip6erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header
Fixes: df16bd187e9d ("net: erspan: refactor existing erspan code") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ip_gre: fix possible use-after-free in erspan_rcv
erspan tunnels run __iptunnel_pull_header on received skbs to remove
gre and erspan headers. This can determine a possible use-after-free
accessing pkt_md pointer in erspan_rcv since the packet will be 'uncloned'
running pskb_expand_head if it is a cloned gso skb (e.g if the packet has
been sent though a veth device). Fix it resetting pkt_md pointer after
__iptunnel_pull_header
Fixes: df16bd187e9d ("net: erspan: refactor existing erspan code") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tadeusz Struk [Tue, 12 Feb 2019 23:42:05 +0000 (15:42 -0800)]
selftests/tpm2: Open tpm dev in unbuffered mode
In order to have control over how many bytes are read or written
the device needs to be opened in unbuffered mode.
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com>
Tadeusz Struk [Tue, 12 Feb 2019 23:42:10 +0000 (15:42 -0800)]
selftests/tpm2: Extend tests to cover partial reads
Three new tests added:
1. Send get random cmd, read header in 1st read, read the rest in second
read - expect success
2. Send get random cmd, read only part of the response, send another
get random command, read the response - expect success
3. Send get random cmd followed by another get random cmd, without
reading the first response - expect the second cmd to fail with -EBUSY
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com>
Fixes the warning reported by Clang:
security/keys/trusted.c:146:17: warning: passing an object that
undergoes default
argument promotion to 'va_start' has undefined behavior [-Wvarargs]
va_start(argp, h3);
^
security/keys/trusted.c:126:37: note: parameter of type 'unsigned
char' is declared here
unsigned char *h2, unsigned char h3, ...)
^
Specifically, it seems that both the C90 (4.8.1.1) and C11 (7.16.1.4)
standards explicitly call this out as undefined behavior:
The parameter parmN is the identifier of the rightmost parameter in
the variable parameter list in the function definition (the one just
before the ...). If the parameter parmN is declared with ... or with a
type that is not compatible with the type that results after
application of the default argument promotions, the behavior is
undefined.
Link: https://github.com/ClangBuiltLinux/linux/issues/41 Link: https://www.eskimo.com/~scs/cclass/int/sx11c.html Suggested-by: David Laight <David.Laight@aculab.com> Suggested-by: Denis Kenzior <denkenz@gmail.com> Suggested-by: James Bottomley <jejb@linux.vnet.ibm.com> Suggested-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com>
Jarkko Sakkinen [Mon, 25 Mar 2019 14:43:10 +0000 (16:43 +0200)]
KEYS: trusted: allow trusted.ko to initialize w/o a TPM
Allow trusted.ko to initialize w/o a TPM. This commit also adds checks
to the exported functions to fail when a TPM is not available.
Fixes: a6b46cac22a6 ("KEYS: trusted: explicitly use tpm_chip structure...") Cc: James Morris <jmorris@namei.org> Reported-by: Dan Williams <dan.j.williams@intel.com> Tested-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com>
Tadeusz Struk [Wed, 27 Mar 2019 18:32:38 +0000 (11:32 -0700)]
tpm: fix an invalid condition in tpm_common_poll
The poll condition should only check response_length,
because reads should only be issued if there is data to read.
The response_read flag only prevents double writes.
The problem was that the write set the response_read to false,
enqued a tpm job, and returned. Then application called poll
which checked the response_read flag and returned EPOLLIN.
Then the application called read, but got nothing.
After all that the async_work kicked in.
Added also mutex_lock around the poll check to prevent
other possible race conditions.
Fixes: 0c685c32c68a09c98c ("tpm: add support for partial reads") Reported-by: Mantas Mikulėnas <grawity@gmail.com> Tested-by: Mantas Mikulėnas <grawity@gmail.com> Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: James Morris <james.morris@microsoft.com>
Jarkko Sakkinen [Fri, 22 Mar 2019 10:51:20 +0000 (12:51 +0200)]
tpm: turn on TPM on suspend for TPM 1.x
tpm_chip_start/stop() should be also called for TPM 1.x devices on
suspend. Add that functionality back. Do not lock the chip because
it is unnecessary as there are no multiple threads using it when
doing the suspend.
Fixes: 5c5b996c8cb9 ("tpm: take TPM chip power gating out of tpm_transmit()") Reported-by: Paul Zimmerman <pauldzim@gmail.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Tested-by: Domenico Andreoli <domenico.andreoli@linux.com> Signed-off-by: James Morris <james.morris@microsoft.com>
There's a significant number of reports that re-enabling ASPM causes
different issues, ranging from decreased performance to system not
booting at all. This affects only a minority of users, but the number
of affected users is big enough that we better switch off ASPM again.
This will hurt notebook users who are not affected by the issues, they
may see decreased battery runtime w/o ASPM. With the PCI core folks is
being discussed to add generic sysfs attributes to control ASPM.
Once this is in place brave enough users can re-enable ASPM on their
system.
Fixes: ba9ee823f01d ("r8169: Reinstate ASPM Support") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When moving the documentation for the ieee802154 subsystem from
plain text to rst the file pattern in the MAINTAINERS file got wrong.
Updating it here to fix scripts using this file.
Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Mon, 18 Mar 2019 11:00:58 +0000 (12:00 +0100)]
mac80211: make ieee80211_schedule_txq schedule empty TXQs
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 8282e2cbe0025 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we just set this to 2048, and have multiple limits you
can select from, the total number might run over and cause
a warning in cfg80211. This doesn't make sense, so we just
calculate the total max_interfaces now.
Miaohe Lin [Mon, 8 Apr 2019 02:04:20 +0000 (10:04 +0800)]
net: vrf: Fix ping failed when vrf mtu is set to 0
When the mtu of a vrf device is set to 0, it would cause ping
failed. So I think we should limit vrf mtu in a reasonable range
to solve this problem. I set dev->min_mtu to IPV6_MIN_MTU, so it
will works for both ipv4 and ipv6. And if dev->max_mtu still be 0
can be confusing, so I set dev->max_mtu to ETH_MAX_MTU.
Here is the reproduce step:
1.Config vrf interface and set mtu to 0:
3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrf1 state UP mode DEFAULT group default qlen 1000
link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff
2.Ping peer:
3: enp4s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel
master vrf1 state UP group default qlen 1000
link/ether 52:54:00:9e:dd:c1 brd ff:ff:ff:ff:ff:ff
inet 10.0.0.1/16 scope global enp4s0
valid_lft forever preferred_lft forever
connect: Network is unreachable
3.Set mtu to default value, ping works:
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_seq=1 ttl=64 time=1.88 ms
Fixes: 30231026b07e2 ("net: vrf: remove MTU limits for vrf device") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Qian Cai [Sat, 6 Apr 2019 22:59:01 +0000 (18:59 -0400)]
slab: fix a crash by reading /proc/slab_allocators
The commit 107202cfb263 ("slab: implement slab_root_caches list")
changes the name of the list node within "struct kmem_cache" from "list"
to "root_caches_node", but leaks_show() still use the "list" which
causes a crash when reading /proc/slab_allocators.
You need to have CONFIG_SLAB=y and CONFIG_MEMCG=y to see the problem,
because without MEMCG all slab caches are root caches, and the "list"
node happens to be the right one.
Fixes: 107202cfb263 ("slab: implement slab_root_caches list") Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Tobin C. Harding <tobin@kernel.org> Cc: Tejun Heo <tj@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes from the last few weeks. Most of them are
smaller tweaks and fixes to DT and hardware descriptions for boards.
Some of the more significant ones are:
- eMMC and RGMII stability tweaks for rk3288
- DDC fixes for Rock PI 4
- Audio fixes for two TI am335x eval boards
- D_CAN clock fix for am335x
- Compilation fixes for clang
- !HOTPLUG_CPU compilation fix for one of the new platforms this
release (milbeaut)
- A revert of a gpio fix for nomadik that instead was fixed in the
gpio subsystem
- Whitespace fix for the DT JSON schema (no tabs allowed)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
ARM: milbeaut: fix build with !CONFIG_HOTPLUG_CPU
ARM: iop: don't use using 64-bit DMA masks
ARM: orion: don't use using 64-bit DMA masks
Revert "ARM: dts: nomadik: Fix polarity of SPI CS"
dt-bindings: cpu: Fix JSON schema
arm/mach-at91/pm : fix possible object reference leak
ARM: dts: at91: Fix typo in ISC_D0 on PC9
ARM: dts: Fix dcan clkctrl clock for am3
reset: meson-audio-arb: Fix missing .owner setting of reset_controller_dev
dt-bindings: reset: meson-g12a: Add missing USB2 PHY resets
ARM: dts: rockchip: Remove #address/#size-cells from rk3288-veyron gpio-keys
ARM: dts: rockchip: Remove #address/#size-cells from rk3288 mipi_dsi
ARM: dts: rockchip: Fix gpu opp node names for rk3288
ARM: dts: am335x-evmsk: Correct the regulators for the audio codec
ARM: dts: am335x-evm: Correct the regulators for the audio codec
ARM: OMAP2+: add missing of_node_put after of_device_is_available
ARM: OMAP1: ams-delta: Fix broken GPIO ID allocation
arm64: dts: stratix10: add the sysmgr-syscon property from the gmac's
arm64: dts: rockchip: fix rk3328 sdmmc0 write errors
arm64: dts: rockchip: fix rk3328 rgmii high tx error rate
...
Merge tag 'for-linus-20190407' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Fixups for the pf/pcd queue handling (YueHaibing)
- Revert of the three direct issue changes as they have been proven to
cause an issue with dm-mpath (Bart)
- Plug rq_count reset fix (Dongli)
- io_uring double free in fileset registration error handling (me)
- Make null_blk handle bad numa node passed in (John)
- BFQ ifdef fix (Konstantin)
- Flush queue leak fix (Shenghui)
- Plug trace fix (Yufen)
* tag 'for-linus-20190407' of git://git.kernel.dk/linux-block:
xsysace: Fix error handling in ace_setup
null_blk: prevent crash from bad home_node value
block: Revert v5.0 blk_mq_request_issue_directly() changes
paride/pcd: Fix potential NULL pointer dereference and mem leak
blk-mq: do not reset plug->rq_count before the list is sorted
paride/pf: Fix potential NULL pointer dereference
io_uring: fix double free in case of fileset regitration failure
blk-mq: add trace block plug and unplug for multiple queues
block: use blk_free_flush_queue() to free hctx->fq in blk_mq_init_hctx
block/bfq: fix ifdef for CONFIG_BFQ_GROUP_IOSCHED=y
Arnd Bergmann [Wed, 13 Mar 2019 21:19:16 +0000 (22:19 +0100)]
ARM: milbeaut: fix build with !CONFIG_HOTPLUG_CPU
When HOTPLUG_CPU is disabled, some fields in the smp operations
are not available or needed:
arch/arm/mach-milbeaut/platsmp.c:90:3: error: field designator 'cpu_die' does not refer to any field in type
'struct smp_operations'
.cpu_die = m10v_cpu_die,
^
arch/arm/mach-milbeaut/platsmp.c:91:3: error: field designator 'cpu_kill' does not refer to any field in type
'struct smp_operations'
.cpu_kill = m10v_cpu_kill,
^
Hide them in an #ifdef like the other platforms do.
Fixes: 4e2b9abd0d73 ("ARM: milbeaut: Add basic support for Milbeaut m10v SoC") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Olof Johansson <olof@lixom.net>
can you please revert this patch. It was the wrong solution to the
wrong problem, and I must have acted in stress. Andrey fixed the
real bug in a proper way in these commits:
Olof Johansson [Sun, 7 Apr 2019 22:16:38 +0000 (15:16 -0700)]
Merge tag 'omap-for-v5.1/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.1-rc cycle
Few small fixes for omap variants:
- Fix ams-delta gpio IDs
- Add missing of_node_put for omapdss platform init code
- Fix unconfigured audio regulators for two am335x boards
- Fix use of wrong offset for am335x d_can clocks
* tag 'omap-for-v5.1/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dcan clkctrl clock for am3
ARM: dts: am335x-evmsk: Correct the regulators for the audio codec
ARM: dts: am335x-evm: Correct the regulators for the audio codec
ARM: OMAP2+: add missing of_node_put after of_device_is_available
ARM: OMAP1: ams-delta: Fix broken GPIO ID allocation
Olof Johansson [Sun, 7 Apr 2019 22:16:09 +0000 (15:16 -0700)]
Merge tag 'at91-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes for 5.1
- fix a typo in sama5d2 pinmuxing which concerns the ISC data 0 signal
- fix a kobject reference leak
* tag 'at91-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
arm/mach-at91/pm : fix possible object reference leak
ARM: dts: at91: Fix typo in ISC_D0 on PC9
Olof Johansson [Sun, 7 Apr 2019 22:15:31 +0000 (15:15 -0700)]
Merge tag 'v5.1-rockchip-dtfixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Fixes for dtc warnings, fixes for ethernet transfers on rk3328,
sd-card related fixes on both rk3328 ans rk3288-tinker and a
regulator fix on rock64 and making ddc actually work on the
Rock PI 4 due to missing the ddc bus.
* tag 'v5.1-rockchip-dtfixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Remove #address/#size-cells from rk3288-veyron gpio-keys
ARM: dts: rockchip: Remove #address/#size-cells from rk3288 mipi_dsi
ARM: dts: rockchip: Fix gpu opp node names for rk3288
arm64: dts: rockchip: fix rk3328 sdmmc0 write errors
arm64: dts: rockchip: fix rk3328 rgmii high tx error rate
ARM: dts: rockchip: Fix SD card detection on rk3288-tinker
arm64: dts: rockchip: Fix vcc_host1_5v GPIO polarity on rk3328-rock64
ARM: dts: rockchip: fix rk3288 cpu opp node reference
arm64: dts: rockchip: add DDC bus on Rock Pi 4
arm64: dts: rockchip: fix rk3328-roc-cc gmac2io tx/rx_delay
Olof Johansson [Sun, 7 Apr 2019 22:14:30 +0000 (15:14 -0700)]
Merge tag 'stratix10_fix_for_v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
arm64: dts: stratix10: fix emac loading warning
- Add missing "altr,sysmgr-syscon" property to all gmac nodes
* tag 'stratix10_fix_for_v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: stratix10: add the sysmgr-syscon property from the gmac's
Olof Johansson [Sun, 7 Apr 2019 22:14:00 +0000 (15:14 -0700)]
Merge tag 'reset-fixes-for-v5.1' of git://git.pengutronix.de/pza/linux into arm/fixes
Reset controller fixes for v5.1
This tag adds missing USB PHY reset lines to the Meson G12A reset
controller header and fixes the Meson Audio ARB driver to prevent
module unloading while it is in use.
* tag 'reset-fixes-for-v5.1' of git://git.pengutronix.de/pza/linux:
reset: meson-audio-arb: Fix missing .owner setting of reset_controller_dev
dt-bindings: reset: meson-g12a: Add missing USB2 PHY resets
Maxime Ripard [Mon, 18 Mar 2019 10:05:21 +0000 (11:05 +0100)]
dt-bindings: cpu: Fix JSON schema
Commit ad057467f135 ("dt-bindings: arm: Add SMP enable-method for
Milbeaut") added support for a new cpu enable-method, but did so using
tabulations to ident. This is however invalid in the syntax, and resulted
in a failure when trying to use that schemas for validation.
Use spaces instead of tabs to indent to fix this.
Fixes: ad057467f135 ("dt-bindings: arm: Add SMP enable-method for Milbeaut") Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Sugaya Taichi <sugaya.taichi@socionext.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Merge tag 'for-linus-5.1b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"One minor fix and a small cleanup for the xen privcmd driver"
* tag 'for-linus-5.1b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Prevent buffer overflow in privcmd ioctl
xen: use struct_size() helper in kzalloc()
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five small fixes. Four in three drivers: qedi, lpfc and storvsc. The
final one is labelled core, but merely adds a dh rdac entry for Lenovo
systems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Fix missing wakeups on abort threads
scsi: storvsc: Reduce default ring buffer size to 128 Kbytes
scsi: storvsc: Fix calculation of sub-channel count
scsi: core: add new RDAC LENOVO/DE_Series device
scsi: qedi: remove declaration of nvm_image from stack
Dan Carpenter [Wed, 3 Apr 2019 07:13:51 +0000 (10:13 +0300)]
nfc: nci: Potential off by one in ->pipes[] array
This is similar to commit ba60d3ba0955 ("NFC: Fix the number of pipes")
where we changed NFC_HCI_MAX_PIPES from 127 to 128.
As the comment next to the define explains, the pipe identifier is 7
bits long. The highest possible pipe is 127, but the number of possible
pipes is 128. As the code is now, then there is potential for an
out of bounds array access:
net/nfc/nci/hci.c:297 nci_hci_cmd_received() warn: array off by one?
'ndev->hci_dev->pipes[pipe]' '0-127 == 127'
Fixes: 7bc4a77f0fb1 ("NFC: nci: Add HCI over NCI protocol support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 3 Apr 2019 07:12:48 +0000 (10:12 +0300)]
NFC: nci: Add some bounds checking in nci_hci_cmd_received()
This is similar to commit af8e8009b7af ("NFC: Fix possible memory
corruption when handling SHDLC I-Frame commands").
I'm not totally sure, but I think that commit description may have
overstated the danger. I was under the impression that this data came
from the firmware? If you can't trust your networking firmware, then
you're already in trouble.
Anyway, these days we add bounds checking where ever we can and we call
it kernel hardening. Better safe than sorry.
Fixes: 7bc4a77f0fb1 ("NFC: nci: Add HCI over NCI protocol support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'parisc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"A 32-bit boot regression fix introduced in the merge window, a QEMU
detection fix and two fixes by Sven regarding ptrace & kprobes"
* 'parisc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Detect QEMU earlier in boot process
parisc: also set iaoq_b in instruction_pointer_set()
parisc: regs_return_value() should return gpr28
Revert: parisc: Use F_EXTEND() macro in iosapic code
While adding LASI support to QEMU, I noticed that the QEMU detection in
the kernel happens much too late. For example, when a LASI chip is found
by the kernel, it registers the LASI LED driver as well. But when we
run on QEMU it makes sense to avoid spending unnecessary CPU cycles, so
we need to access the running_on_QEMU flag earlier than before.
This patch now makes the QEMU detection the fist task of the Linux
kernel by moving it to where the kernel enters the C-coding.
Sven Schnelle [Thu, 4 Apr 2019 16:16:04 +0000 (18:16 +0200)]
parisc: also set iaoq_b in instruction_pointer_set()
When setting the instruction pointer on PA-RISC we also need
to set the back of the instruction queue to the new offset, otherwise
we will execute on instruction from the new location, and jumping
back to the old location stored in iaoq_b.
Sven Schnelle [Thu, 4 Apr 2019 16:16:03 +0000 (18:16 +0200)]
parisc: regs_return_value() should return gpr28
While working on kretprobes for PA-RISC I was wondering while the
kprobes sanity test always fails on kretprobes. This is caused by
returning gpr20 instead of gpr28.
Kirill Smelkov [Tue, 26 Mar 2019 22:20:43 +0000 (22:20 +0000)]
fs: stream_open - opener for stream-like files so that read and write can run simultaneously without deadlock
Commit db738757ed13 ("vfs: atomic f_pos accesses as per POSIX") added
locking for file.f_pos access and in particular made concurrent read and
write not possible - now both those functions take f_pos lock for the
whole run, and so if e.g. a read is blocked waiting for data, write will
deadlock waiting for that read to complete.
This caused regression for stream-like files where previously read and
write could run simultaneously, but after that patch could not do so
anymore. See e.g. commit 08c082c3dac5 ("xenbus: fix deadlock on writes
to /proc/xen/xenbus") which fixes such regression for particular case of
/proc/xen/xenbus.
The patch that added f_pos lock in 2014 did so to guarantee POSIX thread
safety for read/write/lseek and added the locking to file descriptors of
all regular files. In 2014 that thread-safety problem was not new as it
was already discussed earlier in 2006.
However even though 2006'th version of Linus's patch was adding f_pos
locking "only for files that are marked seekable with FMODE_LSEEK (thus
avoiding the stream-like objects like pipes and sockets)", the 2014
version - the one that actually made it into the tree as db738757ed13 -
is doing so irregardless of whether a file is seekable or not.
The reason that it did so is, probably, that there are many files that
are marked non-seekable, but e.g. their read implementation actually
depends on knowing current position to correctly handle the read. Some
examples:
Despite that, many nonseekable_open users implement read and write with
pure stream semantics - they don't depend on passed ppos at all. And for
those cases where read could wait for something inside, it creates a
situation similar to xenbus - the write could be never made to go until
read is done, and read is waiting for some, potentially external, event,
for potentially unbounded time -> deadlock.
Besides xenbus, there are 14 such places in the kernel that I've found
with semantic patch (see below):
drivers/xen/evtchn.c:667:8-24: ERROR: evtchn_fops: .read() can deadlock .write()
drivers/isdn/capi/capi.c:963:8-24: ERROR: capi_fops: .read() can deadlock .write()
drivers/input/evdev.c:527:1-17: ERROR: evdev_fops: .read() can deadlock .write()
drivers/char/pcmcia/cm4000_cs.c:1685:7-23: ERROR: cm4000_fops: .read() can deadlock .write()
net/rfkill/core.c:1146:8-24: ERROR: rfkill_fops: .read() can deadlock .write()
drivers/s390/char/fs3270.c:488:1-17: ERROR: fs3270_fops: .read() can deadlock .write()
drivers/usb/misc/ldusb.c:310:1-17: ERROR: ld_usb_fops: .read() can deadlock .write()
drivers/hid/uhid.c:635:1-17: ERROR: uhid_fops: .read() can deadlock .write()
net/batman-adv/icmp_socket.c:80:1-17: ERROR: batadv_fops: .read() can deadlock .write()
drivers/media/rc/lirc_dev.c:198:1-17: ERROR: lirc_fops: .read() can deadlock .write()
drivers/leds/uleds.c:77:1-17: ERROR: uleds_fops: .read() can deadlock .write()
drivers/input/misc/uinput.c:400:1-17: ERROR: uinput_fops: .read() can deadlock .write()
drivers/infiniband/core/user_mad.c:985:7-23: ERROR: umad_fops: .read() can deadlock .write()
drivers/gnss/core.c:45:1-17: ERROR: gnss_fops: .read() can deadlock .write()
In addition to the cases above another regression caused by f_pos
locking is that now FUSE filesystems that implement open with
FOPEN_NONSEEKABLE flag, can no longer implement bidirectional
stream-like files - for the same reason as above e.g. read can deadlock
write locking on file.f_pos in the kernel.
FUSE's FOPEN_NONSEEKABLE was added in 2008 in 9328c8d3293f ("fuse:
implement nonseekable open") to support OSSPD. OSSPD implements /dev/dsp
in userspace with FOPEN_NONSEEKABLE flag, with corresponding read and
write routines not depending on current position at all, and with both
read and write being potentially blocking operations:
Corresponding libfuse example/test also describes FOPEN_NONSEEKABLE as
"somewhat pipe-like files ..." with read handler not using offset.
However that test implements only read without write and cannot exercise
the deadlock scenario:
I've actually hit the read vs write deadlock for real while implementing
my FUSE filesystem where there is /head/watch file, for which open
creates separate bidirectional socket-like stream in between filesystem
and its user with both read and write being later performed
simultaneously. And there it is semantically not easy to split the
stream into two separate read-only and write-only channels:
1. We can't change nonseekable_open to include &~FMODE_ATOMIC_POS -
doing so would break many in-kernel nonseekable_open users which
actually use ppos in read/write handlers.
2. Add stream_open() to kernel to open stream-like non-seekable file
descriptors. Read and write on such file descriptors would never use
nor change ppos. And with that property on stream-like files read and
write will be running without taking f_pos lock - i.e. read and write
could be running simultaneously.
3. With semantic patch search and convert to stream_open all in-kernel
nonseekable_open users for which read and write actually do not
depend on ppos and where there is no other methods in file_operations
which assume @offset access.
4. Add FOPEN_STREAM to fs/fuse/ and open in-kernel file-descriptors via
steam_open if that bit is present in filesystem open reply.
It was tempting to change fs/fuse/ open handler to use stream_open
instead of nonseekable_open on just FOPEN_NONSEEKABLE flags, but
grepping through Debian codesearch shows users of FOPEN_NONSEEKABLE,
and in particular GVFS which actually uses offset in its read and
write handlers
so if we would do such a change it will break a real user.
5. Add stream_open and FOPEN_STREAM handling to stable kernels starting
from v3.14+ (the kernel where db738757ed first appeared).
This will allow to patch OSSPD and other FUSE filesystems that
provide stream-like files to return FOPEN_STREAM | FOPEN_NONSEEKABLE
in their open handler and this way avoid the deadlock on all kernel
versions. This should work because fs/fuse/ ignores unknown open
flags returned from a filesystem and so passing FOPEN_STREAM to a
kernel that is not aware of this flag cannot hurt. In turn the kernel
that is not aware of FOPEN_STREAM will be < v3.14 where just
FOPEN_NONSEEKABLE is sufficient to implement streams without read vs
write deadlock.
This patch adds stream_open, converts /proc/xen/xenbus to it and adds
semantic patch to automatically locate in-kernel places that are either
required to be converted due to read vs write deadlock, or that are just
safe to be converted because read and write do not use ppos and there
are no other funky methods in file_operations.
Regarding semantic patch I've verified each generated change manually -
that it is correct to convert - and each other nonseekable_open instance
left - that it is either not correct to convert there, or that it is not
converted due to current stream_open.cocci limitations.
The script also does not convert files that should be valid to convert,
but that currently have .llseek = noop_llseek or generic_file_llseek for
unknown reason despite file being opened with nonseekable_open (e.g.
drivers/input/mousedev.c)
Guenter Roeck [Tue, 19 Feb 2019 16:49:56 +0000 (08:49 -0800)]
xsysace: Fix error handling in ace_setup
If xace hardware reports a bad version number, the error handling code
in ace_setup() calls put_disk(), followed by queue cleanup. However, since
the disk data structure has the queue pointer set, put_disk() also
cleans and releases the queue. This results in blk_cleanup_queue()
accessing an already released data structure, which in turn may result
in a crash such as the following.
Fix the problem by setting the disk queue pointer to NULL before calling
put_disk(). A more comprehensive fix might be to rearrange the code
to check the hardware version before initializing data structures,
but I don't know if this would have undesirable side effects, and
it would increase the complexity of backporting the fix to older kernels.
Fixes: e33982d425b71 ("Add support for Xilinx SystemACE CompactFlash interface") Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jens Axboe <axboe@kernel.dk>
John Pittman [Fri, 5 Apr 2019 21:42:45 +0000 (17:42 -0400)]
null_blk: prevent crash from bad home_node value
At module load, if the selected home_node value is greater than
the available numa nodes, the system will crash in
__alloc_pages_nodemask() due to a bad paging request. Prevent this
user error crash by detecting the bad value, logging an error, and
setting g_home_node back to the default of NUMA_NO_NODE.
Signed-off-by: John Pittman <jpittman@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge tag 'rtc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
- Various alarm fixes for da9063, cros-ec and sh
- sd3078 manufacturer name fix as this was introduced this cycle
* tag 'rtc-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: da9063: set uie_unsupported when relevant
rtc: sd3078: fix manufacturer name
rtc: sh: Fix invalid alarm warning for non-enabled alarm
rtc: cros-ec: Fail suspend/resume if wake IRQ can't be configured
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kernel/sysctl.c: fix out-of-bounds access when setting file-max
mm/util.c: fix strndup_user() comment
sh: fix multiple function definition build errors
MAINTAINERS: add maintainer and replacing reviewer ARM/NUVOTON NPCM
MAINTAINERS: fix bad pattern in ARM/NUVOTON NPCM
mm: writeback: use exact memcg dirty counts
psi: clarify the units used in pressure files
mm/huge_memory.c: fix modifying of page protection by insert_pfn_pmd()
hugetlbfs: fix memory leak for resv_map
mm: fix vm_fault_t cast in VM_FAULT_GET_HINDEX()
lib/lzo: fix bugs for very short or empty input
include/linux/bitrev.h: fix constant bitrev
kmemleak: powerpc: skip scanning holes in the .bss section
lib/string.c: implement a basic bcmp
Will Deacon [Sat, 6 Apr 2019 01:39:38 +0000 (18:39 -0700)]
kernel/sysctl.c: fix out-of-bounds access when setting file-max
Commit 8090042818f5 ("sysctl: handle overflow for file-max") hooked up
min/max values for the file-max sysctl parameter via the .extra1 and
.extra2 fields in the corresponding struct ctl_table entry.
Unfortunately, the minimum value points at the global 'zero' variable,
which is an int. This results in a KASAN splat when accessed as a long
by proc_doulongvec_minmax on 64-bit architectures:
| BUG: KASAN: global-out-of-bounds in __do_proc_doulongvec_minmax+0x5d8/0x6a0
| Read of size 8 at addr ffff2000133d1c20 by task systemd/1
|
| CPU: 0 PID: 1 Comm: systemd Not tainted 5.1.0-rc3-00012-g40b114779944 #2
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x228
| show_stack+0x14/0x20
| dump_stack+0xe8/0x124
| print_address_description+0x60/0x258
| kasan_report+0x140/0x1a0
| __asan_report_load8_noabort+0x18/0x20
| __do_proc_doulongvec_minmax+0x5d8/0x6a0
| proc_doulongvec_minmax+0x4c/0x78
| proc_sys_call_handler.isra.19+0x144/0x1d8
| proc_sys_write+0x34/0x58
| __vfs_write+0x54/0xe8
| vfs_write+0x124/0x3c0
| ksys_write+0xbc/0x168
| __arm64_sys_write+0x68/0x98
| el0_svc_common+0x100/0x258
| el0_svc_handler+0x48/0xc0
| el0_svc+0x8/0xc
|
| The buggy address belongs to the variable:
| zero+0x0/0x40
|
| Memory state around the buggy address:
| ffff2000133d1b00: 00 00 00 00 00 00 00 00 fa fa fa fa 04 fa fa fa
| ffff2000133d1b80: fa fa fa fa 04 fa fa fa fa fa fa fa 04 fa fa fa
| >ffff2000133d1c00: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
| ^
| ffff2000133d1c80: fa fa fa fa 00 fa fa fa fa fa fa fa 00 00 00 00
| ffff2000133d1d00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fix the splat by introducing a unsigned long 'zero_ul' and using that
instead.
Link: http://lkml.kernel.org/r/20190403153409.17307-1-will.deacon@arm.com Fixes: 8090042818f5 ("sysctl: handle overflow for file-max") Signed-off-by: Will Deacon <will.deacon@arm.com> Acked-by: Christian Brauner <christian@brauner.io> Cc: Kees Cook <keescook@chromium.org> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Matteo Croce <mcroce@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Sat, 6 Apr 2019 01:39:34 +0000 (18:39 -0700)]
mm/util.c: fix strndup_user() comment
The kerneldoc misdescribes strndup_user()'s return value.
Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Timur Tabi <timur@freescale.com> Cc: Mihai Caraman <mihai.caraman@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Sat, 6 Apr 2019 01:39:30 +0000 (18:39 -0700)]
sh: fix multiple function definition build errors
Many of the sh CPU-types have their own plat_irq_setup() and
arch_init_clk_ops() functions, so these same (empty) functions in
arch/sh/boards/of-generic.c are not needed and cause build errors.
If there is some case where these empty functions are needed, they can
be retained by marking them as "__weak" while at the same time making
builds that do not need them succeed.
Fixes these build errors:
arch/sh/boards/of-generic.o: In function `plat_irq_setup':
(.init.text+0x134): multiple definition of `plat_irq_setup'
arch/sh/kernel/cpu/sh2/setup-sh7619.o:(.init.text+0x30): first defined here
arch/sh/boards/of-generic.o: In function `arch_init_clk_ops':
(.init.text+0x118): multiple definition of `arch_init_clk_ops'
arch/sh/kernel/cpu/sh2/clock-sh7619.o:(.init.text+0x0): first defined here
Link: http://lkml.kernel.org/r/9ee4e0c5-f100-86a2-bd4d-1d3287ceab31@infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kbuild test robot <lkp@intel.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Rich Felker <dalias@libc.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the process of upstreaming architecture support for ARM/NUVOTON NPCM
include/dt-bindings/clock/nuvoton,npcm7xx-clks.h was renamed
include/dt-bindings/clock/nuvoton,npcm7xx-clock.h without updating
MAINTAINERS. This updates the MAINTAINERS pattern to match the new name
of this file.
Link: http://lkml.kernel.org/r/20190328235752.334462-1-tmaimon77@gmail.com Fixes: 3933112e75be ("MAINTAINERS: Add entry for the Nuvoton NPCM architecture") Signed-off-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> Reported-by: Joe Perches <joe@perches.com> Reviewed-by: Benjamin Fair <benjaminfair@google.com> Cc: Avi Fishman <avifishman70@gmail.com> Cc: Mukesh Ojha <mojha@codeaurora.org> Cc: Nancy Yuen <yuenn@google.com> Cc: Patrick Venture <venture@google.com> Cc: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit a9f2e2d4db71 ("mm: memcontrol: fix excessive complexity in
memory.stat reporting") memcg dirty and writeback counters are managed
as:
1) per-memcg per-cpu values in range of [-32..32]
2) per-memcg atomic counter
When a per-cpu counter cannot fit in [-32..32] it's flushed to the
atomic. Stat readers only check the atomic. Thus readers such as
balance_dirty_pages() may see a nontrivial error margin: 32 pages per
cpu.
Assuming 100 cpus:
4k x86 page_size: 13 MiB error per memcg
64k ppc page_size: 200 MiB error per memcg
Considering that dirty+writeback are used together for some decisions the
errors double.
This inaccuracy can lead to undeserved oom kills. One nasty case is
when all per-cpu counters hold positive values offsetting an atomic
negative value (i.e. per_cpu[*]=32, atomic=n_cpu*-32).
balance_dirty_pages() only consults the atomic and does not consider
throttling the next n_cpu*32 dirty pages. If the file_lru is in the
13..200 MiB range then there's absolutely no dirty throttling, which
burdens vmscan with only dirty+writeback pages thus resorting to oom
kill.
It could be argued that tiny containers are not supported, but it's more
subtle. It's the amount the space available for file lru that matters.
If a container has memory.max-200MiB of non reclaimable memory, then it
will also suffer such oom kills on a 100 cpu machine.
The following test reliably ooms without this patch. This patch avoids
oom kills.
$ cat test
mount -t cgroup2 none /dev/cgroup
cd /dev/cgroup
echo +io +memory > cgroup.subtree_control
mkdir test
cd test
echo 10M > memory.max
(echo $BASHPID > cgroup.procs && exec /memcg-writeback-stress /foo)
(echo $BASHPID > cgroup.procs && exec dd if=/dev/zero of=/foo bs=2M count=100)
$ cat memcg-writeback-stress.c
/*
* Dirty pages from all but one cpu.
* Clean pages from the non dirtying cpu.
* This is to stress per cpu counter imbalance.
* On a 100 cpu machine:
* - per memcg per cpu dirty count is 32 pages for each of 99 cpus
* - per memcg atomic is -99*32 pages
* - thus the complete dirty limit: sum of all counters 0
* - balance_dirty_pages() only sees atomic count -99*32 pages, which
* it max()s to 0.
* - So a workload can dirty -99*32 pages before balance_dirty_pages()
* cares.
*/
#define _GNU_SOURCE
#include <err.h>
#include <fcntl.h>
#include <sched.h>
#include <stdlib.h>
#include <stdio.h>
#include <sys/stat.h>
#include <sys/sysinfo.h>
#include <sys/types.h>
#include <unistd.h>
CPU_ZERO(&affinity);
CPU_SET(cpu, &affinity);
if (sched_setaffinity(0, sizeof(affinity), &affinity))
err(1, "sched_setaffinity");
}
static void dirty_on(int output_fd, int cpu)
{
int i, wrote;
set_affinity(cpu);
for (i = 0; i < 32; i++) {
for (wrote = 0; wrote < bufSize; ) {
int ret = write(output_fd, buf+wrote, bufSize-wrote);
if (ret == -1)
err(1, "write");
wrote += ret;
}
}
}
int main(int argc, char **argv)
{
int cpu, flush_cpu = 1, output_fd;
const char *output;
for (cpu = 0; cpu < get_nprocs(); cpu++) {
if (cpu != flush_cpu)
dirty_on(output_fd, cpu);
}
set_affinity(flush_cpu);
if (fsync(output_fd))
err(1, "fsync(%s)", output);
if (close(output_fd))
err(1, "close(%s)", output);
free(buf);
}
Make balance_dirty_pages() and wb_over_bg_thresh() work harder to
collect exact per memcg counters. This avoids the aforementioned oom
kills.
This does not affect the overhead of memory.stat, which still reads the
single atomic counter.
Why not use percpu_counter? memcg already handles cpus going offline, so
no need for that overhead from percpu_counter. And the percpu_counter
spinlocks are more heavyweight than is required.
It probably also makes sense to use exact dirty and writeback counters
in memcg oom reports. But that is saved for later.
Link: http://lkml.kernel.org/r/20190329174609.164344-1-gthelen@google.com Signed-off-by: Greg Thelen <gthelen@google.com> Reviewed-by: Roman Gushchin <guro@fb.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Tejun Heo <tj@kernel.org> Cc: <stable@vger.kernel.org> [4.16+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Waiman Long [Sat, 6 Apr 2019 01:39:14 +0000 (18:39 -0700)]
psi: clarify the units used in pressure files
The output of the PSI files show a bunch of numbers with no unit. The
psi.txt documentation file also does not indicate what units are used.
One can only find out by looking at the source code. The units are
percentage for the averages and useconds for the total. Make the
information easier to find by documenting the units in psi.txt.
Link: http://lkml.kernel.org/r/20190402193810.3450-1-longman@redhat.com Signed-off-by: Waiman Long <longman@redhat.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Tejun Heo <tj@kernel.org> Cc: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Kravetz [Sat, 6 Apr 2019 01:39:06 +0000 (18:39 -0700)]
hugetlbfs: fix memory leak for resv_map
When mknod is used to create a block special file in hugetlbfs, it will
allocate an inode and kmalloc a 'struct resv_map' via resv_map_alloc().
inode->i_mapping->private_data will point the newly allocated resv_map.
However, when the device special file is opened bd_acquire() will set
inode->i_mapping to bd_inode->i_mapping. Thus the pointer to the
allocated resv_map is lost and the structure is leaked.
Programs to reproduce:
mount -t hugetlbfs nodev hugetlbfs
mknod hugetlbfs/dev b 0 0
exec 30<> hugetlbfs/dev
umount hugetlbfs/
resv_map structures are only needed for inodes which can have associated
page allocations. To fix the leak, only allocate resv_map for those
inodes which could possibly be associated with page allocations.
Link: http://lkml.kernel.org/r/20190401213101.16476-1-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Reported-by: Yufen Yu <yuyufen@huawei.com> Suggested-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Rodgman [Sat, 6 Apr 2019 01:38:58 +0000 (18:38 -0700)]
lib/lzo: fix bugs for very short or empty input
For very short input data (0 - 1 bytes), lzo-rle was not behaving
correctly. Fix this behaviour and update documentation accordingly.
For zero-length input, lzo v0 outputs an end-of-stream marker only,
which was misinterpreted by lzo-rle as a bitstream version number.
Ensure bitstream versions > 0 require a minimum stream length of 5.
Also fixes a bug in handling the tail for very short inputs when a
bitstream version is present.
clang points out with hundreds of warnings that the bitrev macros have a
problem with constant input:
drivers/hwmon/sht15.c:187:11: error: variable '__x' is uninitialized when used within its own initialization
[-Werror,-Wuninitialized]
u8 crc = bitrev8(data->val_status & 0x0F);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
include/linux/bitrev.h:102:21: note: expanded from macro 'bitrev8'
__constant_bitrev8(__x) : \
~~~~~~~~~~~~~~~~~~~^~~~
include/linux/bitrev.h:67:11: note: expanded from macro '__constant_bitrev8'
u8 __x = x; \
~~~ ^
Both the bitrev and the __constant_bitrev macros use an internal
variable named __x, which goes horribly wrong when passing one to the
other.
The obvious fix is to rename one of the variables, so this adds an extra
'_'.
It seems we got away with this because
- there are only a few drivers using bitrev macros
- usually there are no constant arguments to those
- when they are constant, they tend to be either 0 or (unsigned)-1
(drivers/isdn/i4l/isdnhdlc.o, drivers/iio/amplifiers/ad8366.c) and
give the correct result by pure chance.
In fact, the only driver that I could find that gets different results
with this is drivers/net/wan/slic_ds26522.c, which in turn is a driver
for fairly rare hardware (adding the maintainer to Cc for testing).
Link: http://lkml.kernel.org/r/20190322140503.123580-1-arnd@arndb.de Fixes: c754e3ffaa66 ("ARM: 8187/1: add CONFIG_HAVE_ARCH_BITREVERSE to support rbit instruction") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Cc: Zhao Qiang <qiang.zhao@nxp.com> Cc: Yalin Wang <yalin.wang@sonymobile.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmemleak: powerpc: skip scanning holes in the .bss section
Commit d3709fee5088 ("KVM: PPC: Introduce kvm_tmp framework") adds
kvm_tmp[] into the .bss section and then free the rest of unused spaces
back to the page allocator.
With DEBUG_PAGEALLOC=y, it will unmap those pages from kernel. As the
result, kmemleak scan will trigger a panic when it scans the .bss
section with unmapped pages.
This patch creates dedicated kmemleak objects for the .data, .bss and
potentially .data..ro_after_init sections to allow partial freeing via
the kmemleak_free_part() in the powerpc kvm_free_tmp() function.
Link: http://lkml.kernel.org/r/20190321171917.62049-1-catalin.marinas@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Qian Cai <cai@lca.pw> Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc) Tested-by: Qian Cai <cai@lca.pw> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Avi Kivity <avi@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krcmar <rkrcmar@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A recent optimization in Clang (r355672) lowers comparisons of the
return value of memcmp against zero to comparisons of the return value
of bcmp against zero. This helps some platforms that implement bcmp
more efficiently than memcmp. glibc simply aliases bcmp to memcmp, but
an optimized implementation is in the works.
This results in linkage failures for all targets with Clang due to the
undefined symbol. For now, just implement bcmp as a tailcail to memcmp
to unbreak the build. This routine can be further optimized in the
future.
Other ideas discussed:
* A weak alias was discussed, but breaks for architectures that define
their own implementations of memcmp since aliases to declarations are
not permitted (only definitions). Arch-specific memcmp
implementations typically declare memcmp in C headers, but implement
them in assembly.
* -ffreestanding also is used sporadically throughout the kernel.
* -fno-builtin-bcmp doesn't work when doing LTO.
Link: https://bugs.llvm.org/show_bug.cgi?id=41035 Link: https://code.woboq.org/userspace/glibc/string/memcmp.c.html#bcmp Link: https://github.com/llvm/llvm-project/commit/8e16d73346f8091461319a7dfc4ddd18eedcff13 Link: https://github.com/ClangBuiltLinux/linux/issues/416 Link: http://lkml.kernel.org/r/20190313211335.165605-1-ndesaulniers@google.com Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reported-by: Nathan Chancellor <natechancellor@gmail.com> Reported-by: Adhemerval Zanella <adhemerval.zanella@linaro.org> Suggested-by: Arnd Bergmann <arnd@arndb.de> Suggested-by: James Y Knight <jyknight@google.com> Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Suggested-by: Nathan Chancellor <natechancellor@gmail.com> Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'for-5.1/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Two queue_limits stacking fixes: disable discards if underlying
driver does. And propagate BDI_CAP_STABLE_WRITES to fix sporadic
checksum errors.
- Fix that reverts a DM core limit that wasn't needed given that
dm-crypt was already updated to impose an equivalent limit.
- Fix dm-init to properly establish 'const' for __initconst array.
- Fix deadlock in DM integrity target that occurs when overlapping IO
is being issued to it. And two smaller fixes to the DM integrity
target.
* tag 'for-5.1/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm integrity: fix deadlock with overlapping I/O
dm: disable DISCARD if the underlying storage no longer supports it
dm table: propagate BDI_CAP_STABLE_WRITES to fix sporadic checksum errors
dm: revert 86ced6648f43 ("dm: limit the max bio size as BIO_MAX_PAGES * PAGE_SIZE")
dm init: fix const confusion for dm_allowed_targets array
dm integrity: make dm_integrity_init and dm_integrity_exit static
dm integrity: change memcmp to strncmp in dm_integrity_ctr
Merge tag 'vfio-v5.1-rc4' of git://github.com/awilliam/linux-vfio
Pull VFIO fixes from Alex Williamson:
- Fix clang printk format errors (Louis Taylor)
- Declare structure static to fix sparse warning (Wang Hai)
- Limit user DMA mappings per container (CVE-2019-3882) (Alex
Williamson)
* tag 'vfio-v5.1-rc4' of git://github.com/awilliam/linux-vfio:
vfio/type1: Limit DMA mappings per container
vfio/spapr_tce: Make symbol 'tce_iommu_driver_ops' static
vfio/pci: use correct format characters
Merge tag 'trace-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull syscall-get-arguments cleanup and fixes from Steven Rostedt:
"Andy Lutomirski approached me to tell me that the
syscall_get_arguments() implementation in x86 was horrible and gcc
certainly gets it wrong.
He said that since the tracepoints only pass in 0 and 6 for i and n
repectively, it should be optimized for that case. Inspecting the
kernel, I discovered that all users pass in 0 for i and only one file
passing in something other than 6 for the number of arguments. That
code happens to be my own code used for the special syscall tracing.
That can easily be converted to just using 0 and 6 as well, and only
copying what is needed. Which is probably the faster path anyway for
that case.
Along the way, a couple of real fixes came from this as the
syscall_get_arguments() function was incorrect for csky and riscv.
x86 has been optimized to for the new interface that removes the
variable number of arguments, but the other architectures could still
use some loving and take more advantage of the simpler interface"
* tag 'trace-5.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
syscalls: Remove start and number from syscall_set_arguments() args
syscalls: Remove start and number from syscall_get_arguments() args
csky: Fix syscall_get_arguments() and syscall_set_arguments()
riscv: Fix syscall_get_arguments() and syscall_set_arguments()
tracing/syscalls: Pass in hardcoded 6 into syscall_get_arguments()
ptrace: Remove maxargs from task_current_syscall()
dm-integrity will deadlock if overlapping I/O is issued to it, the bug
was introduced by commit f46fa52a89c5 ("dm integrity: implement fair
range locks"). Users rarely use overlapping I/O so this bug went
undetected until now.
Fix this bug by correcting, likely cut-n-paste, typos in
ranges_overlap() and also remove a flawed ranges_overlap() check in
remove_range_unlocked(). This condition could leave unprocessed bios
hanging on wait_list forever.
Cc: stable@vger.kernel.org # v4.19+ Fixes: f46fa52a89c5 ("dm integrity: implement fair range locks") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Marc Orr [Tue, 2 Apr 2019 06:56:00 +0000 (23:56 -0700)]
KVM: x86: nVMX: fix x2APIC VTPR read intercept
Referring to the "VIRTUALIZING MSR-BASED APIC ACCESSES" chapter of the
SDM, when "virtualize x2APIC mode" is 1 and "APIC-register
virtualization" is 0, a RDMSR of 808H should return the VTPR from the
virtual APIC page.
However, for nested, KVM currently fails to disable the read intercept
for this MSR. This means that a RDMSR exit takes precedence over
"virtualize x2APIC mode", and KVM passes through L1's TPR to L2,
instead of sourcing the value from L2's virtual APIC page.
This patch fixes the issue by disabling the read intercept, in VMCS02,
for the VTPR when "APIC-register virtualization" is 0.
The issue described above and fix prescribed here, were verified with
a related patch in kvm-unit-tests titled "Test VMX's virtualize x2APIC
mode w/ nested".
Signed-off-by: Marc Orr <marcorr@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Fixes: 424113db115f1 ("KVM: vmx: speed up MSR bitmap merge") Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Marc Orr [Tue, 2 Apr 2019 06:55:59 +0000 (23:55 -0700)]
KVM: x86: nVMX: close leak of L0's x2APIC MSRs (CVE-2019-3887)
The nested_vmx_prepare_msr_bitmap() function doesn't directly guard the
x2APIC MSR intercepts with the "virtualize x2APIC mode" MSR. As a
result, we discovered the potential for a buggy or malicious L1 to get
access to L0's x2APIC MSRs, via an L2, as follows.
1. L1 executes WRMSR(IA32_SPEC_CTRL, 1). This causes the spec_ctrl
variable, in nested_vmx_prepare_msr_bitmap() to become true.
2. L1 disables "virtualize x2APIC mode" in VMCS12.
3. L1 enables "APIC-register virtualization" in VMCS12.
Now, KVM will set VMCS02's x2APIC MSR intercepts from VMCS12, and then
set "virtualize x2APIC mode" to 0 in VMCS02. Oops.
This patch closes the leak by explicitly guarding VMCS02's x2APIC MSR
intercepts with VMCS12's "virtualize x2APIC mode" control.
The scenario outlined above and fix prescribed here, were verified with
a related patch in kvm-unit-tests titled "Add leak scenario to
virt_x2apic_mode_test".
Note, it looks like this issue may have been introduced inadvertently
during a merge---see 8aa7c77dee58.
Signed-off-by: Marc Orr <marcorr@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge tag 'mm-compaction-5.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux
Pull mm/compaction fixes from Mel Gorman:
"The merge window for 5.1 introduced a number of compaction-related
patches. with intermittent reports of corruption and functional
issues. The bugs are due to sloopy checking of zone boundaries and a
corner case where invalid indexes are used to access the free lists.
Reports are not common but at least two users and 0-day have tripped
over them. There is a chance that one of the syzbot reports are
related but it has not been confirmed properly.
The normal submission path is with Andrew but there have been some
delays and I consider them urgent enough that they should be picked up
before RC4 to avoid duplicate reports.
All of these have been successfully tested on older RC windows. This
will make this branch look like a rebase but in fact, they've simply
been lifted again from Andrew's tree and placed on a fresh branch.
I've no reason to believe that this has invalidated the testing given
the lack of change in compaction and the nature of the fixes"
* tag 'mm-compaction-5.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mel/linux:
mm/compaction.c: abort search if isolation fails
mm/compaction.c: correct zone boundary handling when resetting pageblock skip hints
The n_r3964 line discipline driver was written in a different time, when
SMP machines were rare, and users were trusted to do the right thing.
Since then, the world has moved on but not this code, it has stayed
rooted in the past with its lovely hand-crafted list structures and
loads of "interesting" race conditions all over the place.
After attempting to clean up most of the issues, I just gave up and am
now marking the driver as BROKEN so that hopefully someone who has this
hardware will show up out of the woodwork (I know you are out there!)
and will help with debugging a raft of changes that I had laying around
for the code, but was too afraid to commit as odds are they would break
things.
Many thanks to Jann and Linus for pointing out the initial problems in
this codebase, as well as many reviews of my attempts to fix the issues.
It was a case of whack-a-mole, and as you can see, the mole won.
blk_mq_try_issue_directly() can return BLK_STS*_RESOURCE for requests that
have been queued. If that happens when blk_mq_try_issue_directly() is called
by the dm-mpath driver then dm-mpath will try to resubmit a request that is
already queued and a kernel crash follows. Since it is nontrivial to fix
blk_mq_request_issue_directly(), revert the blk_mq_request_issue_directly()
changes that went into kernel v5.0.
This patch reverts the following commits:
* 052264fa20ab ("blk-mq: replace and kill blk_mq_request_issue_directly") # v5.0.
* a63c0a21f0c3 ("blk-mq: issue directly with bypass 'false' in blk_mq_sched_insert_requests") # v5.0.
* 194a690b8931 ("blk-mq: refactor the code of issue request directly") # v5.0.
Cc: Christoph Hellwig <hch@infradead.org> Cc: Ming Lei <ming.lei@redhat.com> Cc: Jianchao Wang <jianchao.w.wang@oracle.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: James Smart <james.smart@broadcom.com> Cc: Dongli Zhang <dongli.zhang@oracle.com> Cc: Laurence Oberman <loberman@redhat.com> Cc: <stable@vger.kernel.org> Reported-by: Laurence Oberman <loberman@redhat.com> Tested-by: Laurence Oberman <loberman@redhat.com> Fixes: 194a690b8931 ("blk-mq: refactor the code of issue request directly") # v5.0. Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
If alloc_disk fails in pcd_init_units, cd->disk will be
NULL, however in pcd_detect and pcd_exit, it's not check
this before free.It may result a NULL pointer dereference.
Also when register_blkdev failed, blk_cleanup_queue() and
blk_mq_free_tag_set() should be called to free resources.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: a25595154339 ("paride/pcd: cleanup queues when detection fails") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
projects / kernel.git / log