====================
Netfilter/IPVS updates for net-next
The following patchset container Netfilter/IPVS update for net-next:
1) Add UDP tunnel support for ICMP errors in IPVS.
Julian Anastasov says:
This patchset is a followup to the commit that adds UDP/GUE tunnel:
"ipvs: allow tunneling with gue encapsulation".
What we do is to put tunnel real servers in hash table (patch 1),
add function to lookup tunnels (patch 2) and use it to strip the
embedded tunnel headers from ICMP errors (patch 3).
2) Extend xt_owner to match for supplementary groups, from
Lukasz Pawelczyk.
3) Remove unused oif field in flow_offload_tuple object, from
Taehee Yoo.
4) Release basechain counters from workqueue to skip synchronize_rcu()
call. From Florian Westphal.
5) Replace skb_make_writable() by skb_ensure_writable(). Patchset
from Florian Westphal.
6) Checksum support for gue encapsulation in IPVS, from Jacky Hu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Maguire [Fri, 31 May 2019 17:47:14 +0000 (18:47 +0100)]
selftests/bpf: measure RTT from xdp using xdping
xdping allows us to get latency estimates from XDP. Output looks
like this:
./xdping -I eth4 192.168.55.8
Setting up XDP for eth4, please wait...
XDP setup disrupts network connectivity, hit Ctrl+C to quit
Normal ping RTT data
[Ignore final RTT; it is distorted by XDP using the reply]
PING 192.168.55.8 (192.168.55.8) from 192.168.55.7 eth4: 56(84) bytes of data.
64 bytes from 192.168.55.8: icmp_seq=1 ttl=64 time=0.302 ms
64 bytes from 192.168.55.8: icmp_seq=2 ttl=64 time=0.208 ms
64 bytes from 192.168.55.8: icmp_seq=3 ttl=64 time=0.163 ms
64 bytes from 192.168.55.8: icmp_seq=8 ttl=64 time=0.275 ms
4 packets transmitted, 4 received, 0% packet loss, time 3079ms
rtt min/avg/max/mdev = 0.163/0.237/0.302/0.054 ms
XDP RTT data:
64 bytes from 192.168.55.8: icmp_seq=5 ttl=64 time=0.02808 ms
64 bytes from 192.168.55.8: icmp_seq=6 ttl=64 time=0.02804 ms
64 bytes from 192.168.55.8: icmp_seq=7 ttl=64 time=0.02815 ms
64 bytes from 192.168.55.8: icmp_seq=8 ttl=64 time=0.02805 ms
The xdping program loads the associated xdping_kern.o BPF program
and attaches it to the specified interface. If run in client
mode (the default), it will add a map entry keyed by the
target IP address; this map will store RTT measurements, current
sequence number etc. Finally in client mode the ping command
is executed, and the xdping BPF program will use the last ICMP
reply, reformulate it as an ICMP request with the next sequence
number and XDP_TX it. After the reply to that request is received
we can measure RTT and repeat until the desired number of
measurements is made. This is why the sequence numbers in the
normal ping are 1, 2, 3 and 8. We XDP_TX a modified version
of ICMP reply 4 and keep doing this until we get the 4 replies
we need; hence the networking stack only sees reply 8, where
we have XDP_PASSed it upstream since we are done.
In server mode (-s), xdping simply takes ICMP requests and replies
to them in XDP rather than passing the request up to the networking
stack. No map entry is required.
xdping can be run in native XDP mode (the default, or specified
via -N) or in skb mode (-S).
A test program test_xdping.sh exercises some of these options.
Note that native XDP does not seem to XDP_TX for veths, hence -N
is not tested. Looking at the code, it looks like XDP_TX is
supported so I'm not sure if that's expected. Running xdping in
native mode for ixgbe as both client and server works fine.
Changes since v4
- close fds on cleanup (Song Liu)
Changes since v3
- fixed seq to be __be16 (Song Liu)
- fixed fd checks in xdping.c (Song Liu)
Changes since v2
- updated commit message to explain why seq number of last
ICMP reply is 8 not 4 (Song Liu)
- updated types of seq number, raddr and eliminated csum variable
in xdpclient/xdpserver functions as it was not needed (Song Liu)
- added XDPING_DEFAULT_COUNT definition and usage specification of
default/max counts (Song Liu)
Changes since v1
- moved from RFC to PATCH
- removed unused variable in ipv4_csum() (Song Liu)
- refactored ICMP checks into icmp_check() function called by client
and server programs and reworked client and server programs due
to lack of shared code (Song Liu)
- added checks to ensure that SKB and native mode are not requested
together (Song Liu)
Signed-off-by: Alan Maguire <alan.maguire@oracle.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
David S. Miller [Sat, 1 Jun 2019 00:13:19 +0000 (17:13 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-05-31
This series contains updates to the iavf driver.
Nathan Chancellor converts the use of gnu_printf to printf.
Aleksandr modifies the driver to limit the number of RSS queues to the
number of online CPUs in order to avoid creating misconfigured RSS
queues.
Gustavo A. R. Silva converts a couple of instances where sizeof() can be
replaced with struct_size().
Alice makes the remaining changes to the iavf driver to cleanup all the
old "i40evf" references in the driver to iavf, including the file names
that still contained the old driver reference. There was no functional
changes made, just cosmetic to reduce any confusion going forward now
that the iavf driver is the virtual function driver for both i40e and
ice drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiong Wang [Thu, 30 May 2019 20:23:18 +0000 (21:23 +0100)]
bpf: doc: update answer for 32-bit subregister question
There has been quite a few progress around the two steps mentioned in the
answer to the following question:
Q: BPF 32-bit subregister requirements
This patch updates the answer to reflect what has been done.
v2:
- Add missing full stop. (Song Liu)
- Minor tweak on one sentence. (Song Liu)
v1:
- Integrated rephrase from Quentin and Jakub
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
====================
During my work on memcg-based memory accounting for bpf maps
I've done some cleanups and refactorings of the existing
memlock rlimit-based code. It makes it more robust, unifies
size to pages conversion, size checks and corresponding error
codes. Also it adds coverage for cgroup local storage and
socket local storage maps.
It looks like some preliminary work on the mm side might be
required to start working on the memcg-based accounting,
so I'm sending these patches as a separate patchset.
====================
Roman Gushchin [Thu, 30 May 2019 01:03:58 +0000 (18:03 -0700)]
bpf: rework memlock-based memory accounting for maps
In order to unify the existing memlock charging code with the
memcg-based memory accounting, which will be added later, let's
rework the current scheme.
Currently the following design is used:
1) .alloc() callback optionally checks if the allocation will likely
succeed using bpf_map_precharge_memlock()
2) .alloc() performs actual allocations
3) .alloc() callback calculates map cost and sets map.memory.pages
4) map_create() calls bpf_map_init_memlock() which sets map.memory.user
and performs actual charging; in case of failure the map is
destroyed
<map is in use>
1) bpf_map_free_deferred() calls bpf_map_release_memlock(), which
performs uncharge and releases the user
2) .map_free() callback releases the memory
The scheme can be simplified and made more robust:
1) .alloc() calculates map cost and calls bpf_map_charge_init()
2) bpf_map_charge_init() sets map.memory.user and performs actual
charge
3) .alloc() performs actual allocations
<map is in use>
1) .map_free() callback releases the memory
2) bpf_map_charge_finish() performs uncharge and releases the user
The new scheme also allows to reuse bpf_map_charge_init()/finish()
functions for memcg-based accounting. Because charges are performed
before actual allocations and uncharges after freeing the memory,
no bogus memory pressure can be created.
In cases when the map structure is not available (e.g. it's not
created yet, or is already destroyed), on-stack bpf_map_memory
structure is used. The charge can be transferred with the
bpf_map_charge_move() function.
Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Roman Gushchin [Thu, 30 May 2019 01:03:57 +0000 (18:03 -0700)]
bpf: group memory related fields in struct bpf_map_memory
Group "user" and "pages" fields of bpf_map into the bpf_map_memory
structure. Later it can be extended with "memcg" and other related
information.
The main reason for a such change (beside cosmetics) is to pass
bpf_map_memory structure to charging functions before the actual
allocation of bpf_map.
Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Song Liu <songliubraving@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
====================
This patchset adds support for propagating congestion notifications (cn)
to TCP from cgroup inet skb egress BPF programs.
Current cgroup skb BPF programs cannot trigger TCP congestion window
reductions, even when they drop a packet. This patch-set adds support
for cgroup skb BPF programs to send congestion notifications in the
return value when the packets are TCP packets. Rather than the
current 1 for keeping the packet and 0 for dropping it, they can
now return:
NET_XMIT_SUCCESS (0) - continue with packet output
NET_XMIT_DROP (1) - drop packet and do cn
NET_XMIT_CN (2) - continue with packet output and do cn
-EPERM - drop packet
Finally, HBM programs are modified to collect and return more
statistics.
There has been some discussion regarding the best place to manage
bandwidths. Some believe this should be done in the qdisc where it can
also be managed with a BPF program. We believe there are advantages
for doing it with a BPF program in the cgroup/skb callback. For example,
it reduces overheads in the cases where there is on primary workload and
one or more secondary workloads, where each workload is running on its
own cgroupv2. In this scenario, we only need to throttle the secondary
workloads and there is no overhead for the primary workload since there
will be no BPF program attached to its cgroup.
Regardless, we agree that this mechanism should not penalize those that
are not using it. We tested this by doing 1 byte req/reply RPCs over
loopback. Each test consists of 30 sec of back-to-back 1 byte RPCs.
Each test was repeated 50 times with a 1 minute delay between each set
of 10. We then calculated the average RPCs/sec over the 50 tests. We
compare upstream with upstream + patchset and no BPF program as well
as upstream + patchset and a BPF program that just returns ALLOW_PKT.
Here are the results:
upstream 80937 RPCs/sec
upstream + patches, no BPF program 80894 RPCs/sec
upstream + patches, BPF program 80634 RPCs/sec
These numbers indicate that there is no penalty for these patches
The use of congestion notifications improves the performance of HBM when
using Cubic. Without congestion notifications, Cubic will not decrease its
cwnd and HBM will need to drop a large percentage of the packets.
The following results are obtained for rate limits of 1Gbps,
between two servers using netperf, and only one flow. We also show how
reducing the max delayed ACK timer can improve the performance when
using Cubic.
Command used was:
./do_hbm_test.sh -l -D --stats -N -r=<rate> [--no_cn] [dctcp] \
-s=<server running netserver>
where:
<rate> is 1000
--no_cn specifies no cwr notifications
dctcp uses dctcp
Notes:
--no_cn has no effect with DCTCP
Lim = rate limit
DA = maximum delay ack timer
cred = credit in packets
drops = % packets dropped
v1->v2: Insures that only BPF_CGROUP_INET_EGRESS can return values 2 and 3
New egress values apply to all protocols, not just TCP
Cleaned up patch 4, Update BPF_CGROUP_RUN_PROG_INET_EGRESS callers
Removed changes to __tcp_transmit_skb (patch 5), no longer needed
Removed sample use of EDT
v2->v3: Removed the probe timer related changes
v3->v4: Replaced preempt_enable_no_resched() by preempt_enable()
in BPF_PROG_CGROUP_INET_EGRESS_RUN_ARRAY() macro
====================
Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
brakmo [Tue, 28 May 2019 23:59:37 +0000 (16:59 -0700)]
bpf: Update __cgroup_bpf_run_filter_skb with cn
For egress packets, __cgroup_bpf_fun_filter_skb() will now call
BPF_PROG_CGROUP_INET_EGRESS_RUN_ARRAY() instead of PROG_CGROUP_RUN_ARRAY()
in order to propagate congestion notifications (cn) requests to TCP
callers.
For egress packets, this function can return:
NET_XMIT_SUCCESS (0) - continue with packet output
NET_XMIT_DROP (1) - drop packet and notify TCP to call cwr
NET_XMIT_CN (2) - continue with packet output and notify TCP
to call cwr
-EPERM - drop packet
For ingress packets, this function will return -EPERM if any attached
program was found and if it returned != 1 during execution. Otherwise 0
is returned.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
brakmo [Tue, 28 May 2019 23:59:36 +0000 (16:59 -0700)]
bpf: cgroup inet skb programs can return 0 to 3
Allows cgroup inet skb programs to return values in the range [0, 3].
The second bit is used to deterine if congestion occurred and higher
level protocol should decrease rate. E.g. TCP would call tcp_enter_cwr()
The bpf_prog must set expected_attach_type to BPF_CGROUP_INET_EGRESS
at load time if it uses the new return values (i.e. 2 or 3).
The expected_attach_type is currently not enforced for
BPF_PROG_TYPE_CGROUP_SKB. e.g Meaning the current bpf_prog with
expected_attach_type setting to BPF_CGROUP_INET_EGRESS can attach to
BPF_CGROUP_INET_INGRESS. Blindly enforcing expected_attach_type will
break backward compatibility.
This patch adds a enforce_expected_attach_type bit to only
enforce the expected_attach_type when it uses the new
return value.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
brakmo [Tue, 28 May 2019 23:59:35 +0000 (16:59 -0700)]
bpf: Create BPF_PROG_CGROUP_INET_EGRESS_RUN_ARRAY
Create new macro BPF_PROG_CGROUP_INET_EGRESS_RUN_ARRAY() to be used by
__cgroup_bpf_run_filter_skb for EGRESS BPF progs so BPF programs can
request cwr for TCP packets.
Current cgroup skb programs can only return 0 or 1 (0 to drop the
packet. This macro changes the behavior so the low order bit
indicates whether the packet should be dropped (0) or not (1)
and the next bit is used for congestion notification (cn).
Hence, new allowed return values of CGROUP EGRESS BPF programs are:
0: drop packet
1: keep packet
2: drop packet and call cwr
3: keep packet and call cwr
This macro then converts it to one of NET_XMIT values or -EPERM
that has the effect of dropping the packet with no cn.
0: NET_XMIT_SUCCESS skb should be transmitted (no cn)
1: NET_XMIT_DROP skb should be dropped and cwr called
2: NET_XMIT_CN skb should be transmitted and cwr called
3: -EPERM skb should be dropped (no cn)
Note that when more than one BPF program is called, the packet is
dropped if at least one of programs requests it be dropped, and
there is cn if at least one program returns cn.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Colin Ian King [Thu, 30 May 2019 19:04:38 +0000 (20:04 +0100)]
xen-netback: remove redundant assignment to err
The variable err is assigned with the value -ENOMEM that is never
read and it is re-assigned a new value later on. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 30 May 2019 15:57:54 +0000 (16:57 +0100)]
nexthop: remove redundant assignment to err
The variable err is initialized with a value that is never read
and err is reassigned a few statements later. This initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 31 May 2019 19:37:46 +0000 (12:37 -0700)]
Merge branch 'phylink-sfp-updates'
Russell King says:
====================
phylink/sfp updates
This is a series of updates to phylink and sfp:
- Remove an unused net device argument from the phylink MII ioctl
emulation code.
- add support for using interrupts when using a GPIO for link status
tracking, rather than polling it at one second intervals. This
reduces the need to wakeup the CPU every second.
- add support to the MII ioctl API to read and write Clause 45 PHY
registers. I don't know how desirable this is for mainline, but I
have used this facility extensively to investigate the Marvell
88x3310 PHY. A recent illustration of use for this was debugging
the PHY-without-firmware problem recently reported.
- add mandatory attach/detach methods for the upstream side of sfp
bus code, which will allow us to remove the "netdev" structure from
the SFP layers.
- remove the "netdev" structure from the SFP upstream registration
calls, which simplifies PHY to SFP links.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 28 May 2019 09:57:39 +0000 (10:57 +0100)]
net: sfp: remove sfp-bus use of netdevs
The sfp-bus code now no longer has any use for the network device
structure, so remove its use.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 28 May 2019 09:57:34 +0000 (10:57 +0100)]
net: sfp: add mandatory attach/detach methods for sfp buses
Add attach and detach methods for SFP buses, which will allow us to get
rid of the netdev storage in sfp-bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 28 May 2019 09:57:29 +0000 (10:57 +0100)]
net: phy: allow Clause 45 access via mii ioctl
Allow userspace to generate Clause 45 MII access cycles via phylib.
This is useful for tools such as mii-diag to be able to inspect Clause
45 PHYs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 28 May 2019 09:57:23 +0000 (10:57 +0100)]
net: phylink: support for link gpio interrupt
Add support for using GPIO interrupts with a fixed-link GPIO rather than
polling the GPIO every second and invoking the phylink resolution. This
avoids unnecessary calls to mac_config().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Tue, 28 May 2019 09:57:18 +0000 (10:57 +0100)]
net: phylink: remove netdev from phylink mii ioctl emulation
The netdev used in the phylink ioctl emulation is never used, so let's
remove it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a few problems with CONFIG_IPV6=y and
CONFIG_NF_CONNTRACK_BRIDGE=m:
In file included from net/netfilter/utils.c:5:
include/linux/netfilter_ipv6.h: In function 'nf_ipv6_br_defrag':
include/linux/netfilter_ipv6.h:110:9: error: implicit declaration of function 'nf_ct_frag6_gather'; did you mean 'nf_ct_attach'? [-Werror=implicit-function-declaration]
And these too:
net/ipv6/netfilter.c:242:2: error: unknown field 'br_defrag' specified in initializer
net/ipv6/netfilter.c:243:2: error: unknown field 'br_fragment' specified in initializer
This patch includes an original chunk from wenxu.
Fixes: 764dd163ac92 ("netfilter: nf_conntrack_bridge: add support for IPv6") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reported-by: Yuehaibing <yuehaibing@huawei.com> Reported-by: kbuild test robot <lkp@intel.com> Reported-by: wenxu <wenxu@ucloud.cn> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: wenxu <wenxu@ucloud.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacky Hu [Thu, 30 May 2019 00:16:40 +0000 (08:16 +0800)]
ipvs: add checksum support for gue encapsulation
Add checksum support for gue encapsulation with the tun_flags parameter,
which could be one of the values below:
IP_VS_TUNNEL_ENCAP_FLAG_NOCSUM
IP_VS_TUNNEL_ENCAP_FLAG_CSUM
IP_VS_TUNNEL_ENCAP_FLAG_REMCSUM
Signed-off-by: Jacky Hu <hengqing.hu@gmail.com> Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Florian Westphal [Thu, 23 May 2019 13:44:05 +0000 (15:44 +0200)]
netfilter: bridge: convert skb_make_writable to skb_ensure_writable
Back in the day, skb_ensure_writable did not exist. By now, both functions
have the same precondition:
I. skb_make_writable will test in this order:
1. wlen > skb->len -> error
2. if not cloned and wlen <= headlen -> OK
3. If cloned and wlen bytes of clone writeable -> OK
After those checks, skb is either not cloned but needs to pull from
nonlinear area, or writing to head would also alter data of another clone.
In both cases skb_make_writable will then call __pskb_pull_tail, which will
kmalloc a new memory area to use for skb->head.
IOW, after successful skb_make_writable call, the requested length is in
linear area and can be modified, even if skb was cloned.
II. skb_ensure_writable will do this instead:
1. call pskb_may_pull. This handles case 1 above.
After this, wlen is in linear area, but skb might be cloned.
2. return if skb is not cloned
3. return if wlen byte of clone are writeable.
4. fully copy the skb.
So post-conditions are the same:
*len bytes are writeable in linear area without altering any payload data
of a clone, all header pointers might have been changed.
Only differences are that skb_ensure_writable is in the core, whereas
skb_make_writable lives in netfilter core and the inverted return value.
skb_make_writable returns 0 on error, whereas skb_ensure_writable returns
negative value.
For the normal cases performance is similar:
A. skb is not cloned and in linear area:
pskb_may_pull is inline helper, so neither function copies.
B. skb is cloned, write is in linear area and clone is writeable:
both funcions return with step 3.
This series removes skb_make_writable from the kernel.
While at it, pass the needed value instead, its less confusing that way:
There is no special-handling of "0-length" argument in either
skb_make_writable or skb_ensure_writable.
bridge already makes sure ethernet header is in linear area, only purpose
of the make_writable() is is to copy skb->head in case of cloned skbs.
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add ip_vs_find_tunnel() to match tunnel headers
by family, address and optional port. Use it to
properly find the tunnel real server used in
received ICMP errors.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ipvs: allow rs_table to contain different real server types
Before now rs_table was used only for NAT real servers.
Change it to allow TUN real severs from different types,
possibly hashed with different port key.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Alice Michael [Wed, 17 Apr 2019 22:17:37 +0000 (15:17 -0700)]
iavf: update comments and file checks to match iavf
Some small things were missed with recent name changes
from i40e to iavf. Having a separate patch allows to
correct the small misses in one place.
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Wed, 17 Apr 2019 22:17:36 +0000 (15:17 -0700)]
iavf: rename i40e_device to iavf_device
Renaming remaining defines from i40e to iavf
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Wed, 17 Apr 2019 22:17:35 +0000 (15:17 -0700)]
iavf: change remaining i40e defines to be iavf
There were a couple of erroneously missed i40e names to
update to iavf left after the larger chunks. Updated them
separately so now they should all be aligned as iavf.
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Wed, 17 Apr 2019 22:17:34 +0000 (15:17 -0700)]
iavf: rename iavf_client.h defines to match driver name
The defines in iavf_client.h were still vastly i40e, and they
should be iavf.
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Wed, 17 Apr 2019 22:17:33 +0000 (15:17 -0700)]
iavf: rename iavf_status structure flags
rename the flags inside of iavf_status from I40E_*
to IAVF_*
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Wed, 17 Apr 2019 22:17:32 +0000 (15:17 -0700)]
iavf: replace i40e variables with iavf
Update the old variables and flags marked as i40e to match
the iavf name of the driver.
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Wed, 17 Apr 2019 22:17:31 +0000 (15:17 -0700)]
iavf: rename i40e functions to be iavf
Update the old i40e function names to be iavf
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Wed, 17 Apr 2019 22:17:29 +0000 (15:17 -0700)]
iavf: Rename i40e_adminq* files to iavf_adminq*
With the rename of the iavf driver, there were some
files that were missed in renaming. Update these to
be iavf as well.
Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Notice that, in this case, variable bufsz is not necessary, hence it
is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Limiting RSS queues number to online CPUs number in order to
avoid issues with creating misconfigured RSS queues.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
iavf: Use printf instead of gnu_printf for iavf_debug_d
Clang warns:
In file included from drivers/net/ethernet/intel/iavf/iavf_main.c:4:
In file included from drivers/net/ethernet/intel/iavf/iavf.h:37:
In file included from drivers/net/ethernet/intel/iavf/iavf_type.h:8:
drivers/net/ethernet/intel/iavf/iavf_osdep.h:49:18: warning: 'format' attribute argument not supported: gnu_printf [-Wignored-attributes]
__attribute__ ((format(gnu_printf, 3, 4)));
^
1 warning generated.
We can convert from gnu_printf to printf without any side effects for
two reasons:
1. All iavf_debug instances use standard printf formats, as pointed out
by Miguel Ojeda at the below link, meaning gnu_printf is not strictly
required.
2. However, GCC has aliased printf to gnu_printf on Linux since at least
2010 based on git history.
From gcc/c-family/c-format.c:
/* Attributes such as "printf" are equivalent to those such as
"gnu_printf" unless this is overridden by a target. */
static const target_ovr_attr gnu_target_overrides_format_attributes[] =
{
{ "gnu_printf", "printf" },
{ "gnu_scanf", "scanf" },
{ "gnu_strftime", "strftime" },
{ "gnu_strfmon", "strfmon" },
{ NULL, NULL }
};
The mentioned override only happens on Windows (mingw32). Changing from
gnu_printf to printf is a no-op for GCC and stops Clang from warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/111 Suggested-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Fix OOPS during nf_tables rule dump, from Florian Westphal.
2) Use after free in ip_vs_in, from Yue Haibing.
3) Fix various kTLS bugs (NULL deref during device removal resync,
netdev notification ignoring, etc.) From Jakub Kicinski.
4) Fix ipv6 redirects with VRF, from David Ahern.
5) Memory leak fix in igmpv3_del_delrec(), from Eric Dumazet.
6) Missing memory allocation failure check in ip6_ra_control(), from
Gen Zhang. And likewise fix ip_ra_control().
7) TX clean budget logic error in aquantia, from Igor Russkikh.
8) SKB leak in llc_build_and_send_ui_pkt(), from Eric Dumazet.
9) Double frees in mlx5, from Parav Pandit.
10) Fix lost MAC address in r8169 during PCI D3, from Heiner Kallweit.
11) Fix botched register access in mvpp2, from Antoine Tenart.
12) Use after free in napi_gro_frags(), from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (89 commits)
net: correct zerocopy refcnt with udp MSG_MORE
ethtool: Check for vlan etype or vlan tci when parsing flow_rule
net: don't clear sock->sk early to avoid trouble in strparser
net-gro: fix use-after-free read in napi_gro_frags()
net: dsa: tag_8021q: Create a stable binary format
net: dsa: tag_8021q: Change order of rx_vid setup
net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue value
ipv4: tcp_input: fix stack out of bounds when parsing TCP options.
mlxsw: spectrum: Prevent force of 56G
mlxsw: spectrum_acl: Avoid warning after identical rules insertion
net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT
r8169: fix MAC address being lost in PCI D3
net: core: support XDP generic on stacked devices.
netvsc: unshare skb in VF rx handler
udp: Avoid post-GRO UDP checksum recalculation
net: phy: dp83867: Set up RGMII TX delay
net: phy: dp83867: do not call config_init twice
net: phy: dp83867: increase SGMII autoneg timer duration
net: phy: dp83867: fix speed 10 in sgmii mode
net: phy: marvell10g: report if the PHY fails to boot firmware
...
Linus Torvalds [Fri, 31 May 2019 04:05:23 +0000 (21:05 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The fixes are still trickling in for arm64, but the only really
significant one here is actually fixing a regression in the botched
module relocation range checking merged for -rc2.
Hopefully we've nailed it this time.
- Fix implementation of our set_personality() system call, which
wasn't being wrapped properly
- Fix system call function types to keep CFI happy
- Fix siginfo layout when delivering SIGKILL after a kernel fault
- Really fix module relocation range checking"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: use the correct function type for __arm64_sys_ni_syscall
arm64: use the correct function type in SYSCALL_DEFINE0
arm64: fix syscall_fn_t type
signal/arm64: Use force_sig not force_sig_fault for SIGKILL
arm64/module: revert to unsigned interpretation of ABS16/32 relocations
arm64: Fix the arm64_personality() syscall wrapper redirection
Linus Torvalds [Fri, 31 May 2019 03:52:40 +0000 (20:52 -0700)]
Merge tag 'for-5.2-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few more fixes for bugs reported by users, fuzzing tools and
regressions:
- fix crashes in relocation:
+ resuming interrupted balance operation does not properly clean
up orphan trees
+ with enabled qgroups, resuming needs to be more careful about
block groups due to limited context when updating qgroups
- fsync and logging fixes found by fuzzing
- incremental send fixes for no-holes and clone
- fix spin lock type used in timer function for zstd"
* tag 'for-5.2-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix race updating log root item during fsync
Btrfs: fix wrong ctime and mtime of a directory after log replay
Btrfs: fix fsync not persisting changed attributes of a directory
btrfs: qgroup: Check bg while resuming relocation to avoid NULL pointer dereference
btrfs: reloc: Also queue orphan reloc tree for cleanup to avoid BUG_ON()
Btrfs: incremental send, fix emission of invalid clone operations
Btrfs: incremental send, fix file corruption when no-holes feature is enabled
btrfs: correct zstd workspace manager lock to use spin_lock_bh()
btrfs: Ensure replaced device doesn't have pending chunk allocation
Linus Torvalds [Fri, 31 May 2019 02:58:59 +0000 (19:58 -0700)]
Merge tag 'sound-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No big surprises here, just a few device-specific fixes.
HD-audio received several fixes for Acer, Dell, Huawei and other
laptops as well as the workaround for the new Intel chipset. One
significant one-liner fix is the disablement of the node-power saving
on Realtek codecs, which may potentially cover annoying bugs like the
background noises or click noises on many devices.
Other than that, a fix for FireWire bit definitions, and another fix
for LINE6 USB audio bug that was discovered by syzkaller"
* tag 'sound-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fireface: Use ULL suffixes for 64-bit constants
ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops
ALSA: line6: Assure canceling delayed work at disconnection
ALSA: hda - Force polling mode on CNL for fixing codec communication
ALSA: hda/realtek - Enable micmute LED for Huawei laptops
ALSA: hda/realtek - Set default power save node to 0
ALSA: hda/realtek - Check headset type by unplug and resume
Willem de Bruijn [Thu, 30 May 2019 22:01:21 +0000 (18:01 -0400)]
net: correct zerocopy refcnt with udp MSG_MORE
TCP zerocopy takes a uarg reference for every skb, plus one for the
tcp_sendmsg_locked datapath temporarily, to avoid reaching refcnt zero
as it builds, sends and frees skbs inside its inner loop.
UDP and RAW zerocopy do not send inside the inner loop so do not need
the extra sock_zerocopy_get + sock_zerocopy_put pair. Commit 52900d22288ed ("udp: elide zerocopy operation in hot path") introduced
extra_uref to pass the initial reference taken in sock_zerocopy_alloc
to the first generated skb.
But, sock_zerocopy_realloc takes this extra reference at the start of
every call. With MSG_MORE, no new skb may be generated to attach the
extra_uref to, so refcnt is incorrectly 2 with only one skb.
Do not take the extra ref if uarg && !tcp, which implies MSG_MORE.
Update extra_uref accordingly.
This conditional assignment triggers a false positive may be used
uninitialized warning, so have to initialize extra_uref at define.
Changes v1->v2: fix typo in Fixes SHA1
Fixes: 52900d22288e7 ("udp: elide zerocopy operation in hot path") Reported-by: syzbot <syzkaller@googlegroups.com> Diagnosed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 30 May 2019 22:17:05 +0000 (15:17 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-05-30
This series contains updates to ice driver only.
Brett continues his work with interrupt handling by fixing an issue
where were writing to the incorrect register to disable all VF
interrupts.
Tony consolidates the unicast and multicast MAC filters into a single
new function.
Anirudh adds support for virtual channel vector mapping to receive and
transmit queues. This uses a bitmap to associate indicated queues with
the specified vector. Makes several cosmetic code cleanups, as well as
update the driver to align with the current specification for managing
MAC operation codes (opcodes).
Paul adds support for Forward Error Correction (FEC) and also adds the
ethtool get and set handlers to modify FEC parameters.
Bruce cleans up the driver code to fix a number of issues, such as,
reducing the scope of some local variables, reduce the number of
de-references by changing a local variable and reorder the code to
remove unnecessary "goto's".
Dave adds switch rules to be able to handle LLDP packets and in the
process, fix a couple of issues found, like stop treating DCBx state of
"not started" as an error and stop hard coding the filter information
flag to transmit.
Jacob updates the driver to allow for more granular debugging by
developers by using a distinct separate bit for dumping firmware logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool: Check for vlan etype or vlan tci when parsing flow_rule
When parsing an ethtool flow spec to build a flow_rule, the code checks
if both the vlan etype and the vlan tci are specified by the user to add
a FLOW_DISSECTOR_KEY_VLAN match.
However, when the user only specified a vlan etype or a vlan tci, this
check silently ignores these parameters.
will result in no error being issued, but the equivalent rule will be
created and passed to the NIC driver :
ethtool -N eth0 flow-type udp4 action -1 loc 0
In the end, neither the NIC driver using the rule nor the end user have
a way to know that these keys were dropped along the way, or that
incorrect parameters were entered.
This kind of check should be left to either the driver, or the ethtool
flow spec layer.
This commit makes so that ethtool parameters are forwarded as-is to the
NIC driver.
Since none of the users of ethtool_rx_flow_rule_create are using the
VLAN dissector, I don't think this qualifies as a regression.
Fixes: eca4205f9ec3 ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Acked-by: Pablo Neira Ayuso <pablo@gnumonks.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 30 May 2019 22:02:33 +0000 (15:02 -0700)]
Merge branch 'complex-c45-phys'
Heiner Kallweit says:
====================
net: phy: improve handling of more complex C45 PHY's
This series tries to address few problematic aspects raised by
Russell. Concrete example is the Marvell 88x3310, the changes
should be helpful for other complex C45 PHY's too.
v2:
- added patch enabling interrupts also if phylib state machine
isn't started
- removed patch dealing with the double link status read
This one needs little bit more thinking and will go separately.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 30 May 2019 13:11:06 +0000 (15:11 +0200)]
net: phy: export phy_queue_state_machine
We face the issue that link change interrupt and link status may be
reported by different PHY layers. As a result the link change
interrupt may occur before the link status changes.
Export phy_queue_state_machine to allow PHY drivers to specify a
delay between link status change interrupt and link status check.
v2:
- change jiffies parameter type to unsigned long
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Suggested-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 30 May 2019 13:10:06 +0000 (15:10 +0200)]
net: phy: add callback for custom interrupt handler to struct phy_driver
The phylib interrupt handler handles link change events only currently.
However PHY drivers may want to use other interrupt sources too,
e.g. to report temperature monitoring events. Therefore add a callback
to struct phy_driver allowing PHY drivers to implement a custom
interrupt handler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 30 May 2019 13:09:15 +0000 (15:09 +0200)]
net: phy: enable interrupts when PHY is attached already
This patch is a step towards allowing PHY drivers to handle more
interrupt sources than just link change. E.g. several PHY's have
built-in temperature monitoring and can raise an interrupt if a
temperature threshold is exceeded. We may be interested in such
interrupts also if the phylib state machine isn't started.
Therefore move enabling interrupts to phy_request_interrupt().
v2:
- patch added to series
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Thu, 30 May 2019 12:20:40 +0000 (15:20 +0300)]
qed: Fix static checker warning
In some cases abs_ppfid could be printed without being initialized.
Fixes: 79284adeb99e ("qed: Add llh ppfid interface and 100g support for offload protocols") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Thu, 30 May 2019 06:09:07 +0000 (09:09 +0300)]
net: dsa: Add error path handling in dsa_tree_setup()
In case a call to dsa_tree_setup() fails, an attempt to cleanup is made
by calling dsa_tree_remove_switch(), which should take care of
removing/unregistering any resources previously allocated. This does not
happen because it is conditioned by dst->setup being true, which is set
only after _all_ setup steps were performed successfully.
This is especially interesting when the internal MDIO bus is registered
but afterwards, a port setup fails and the mdiobus_unregister() is never
called. This leads to a BUG_ON() complaining about the fact that it's
trying to free an MDIO bus that's still registered.
Add proper error handling in all functions branching from
dsa_tree_setup().
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reported-by: kernel test robot <rong.a.chen@intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid this issue set sock->sk after sk_prot->close.
My grepping and testing did not discover any code which
would depend on the current behaviour.
Fixes: c46234ebb4d1 ("tls: RX path for ktls") Reported-by: David Beckett <david.beckett@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 29 May 2019 22:36:10 +0000 (15:36 -0700)]
net-gro: fix use-after-free read in napi_gro_frags()
If a network driver provides to napi_gro_frags() an
skb with a page fragment of exactly 14 bytes, the call
to gro_pull_from_frag0() will 'consume' the fragment
by calling skb_frag_unref(skb, 0), and the page might
be freed and reused.
Reading eth->h_proto at the end of napi_frags_skb() might
read mangled data, or crash under specific debugging features.
BUG: KASAN: use-after-free in napi_frags_skb net/core/dev.c:5833 [inline]
BUG: KASAN: use-after-free in napi_gro_frags+0xc6f/0xd10 net/core/dev.c:5841
Read of size 2 at addr ffff88809366840c by task syz-executor599/8957
Fixes: a50e233c50db ("net-gro: restore frag0 optimization") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 30 May 2019 21:47:14 +0000 (14:47 -0700)]
Merge branch 'Fixes-for-DSA-tagging-using-802-1Q'
Vladimir Oltean says:
====================
Fixes for DSA tagging using 802.1Q
During the prototyping for the "Decoupling PHYLINK from struct
net_device" patchset, the CPU port of the sja1105 driver was moved to a
different spot. This uncovered an issue in the tag_8021q DSA code,
which used to work by mistake - the CPU port was the last hardware port
numerically, and this was masking an ordering issue which is very likely
to be seen in other drivers that make use of 802.1Q tags.
A question was also raised whether the VID numbers bear any meaning, and
the conclusion was that they don't, at least not in an absolute sense.
The second patch defines bit fields inside the DSA 802.1Q VID so that
tcpdump can decode it unambiguously (although the meaning is now clear
even by visual inspection).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Wed, 29 May 2019 21:42:31 +0000 (00:42 +0300)]
net: dsa: tag_8021q: Create a stable binary format
Tools like tcpdump need to be able to decode the significance of fake
VLAN headers that DSA uses to separate switch ports.
But currently these have no global significance - they are simply an
ordered list of DSA_MAX_SWITCHES x DSA_MAX_PORTS numbers ending at 4095.
The reason why this is submitted as a fix is that the existing mapping
of VIDs should not enter into a stable kernel, so we can pretend that
only the new format exists. This way tcpdump won't need to try to make
something out of the VLAN tags on 5.2 kernels.
Fixes: f9bbe4477c30 ("net: dsa: Optional VLAN-based port separation for switches without tagging") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Wed, 29 May 2019 21:42:30 +0000 (00:42 +0300)]
net: dsa: tag_8021q: Change order of rx_vid setup
The 802.1Q tagging performs an unbalanced setup in terms of RX VIDs on
the CPU port. For the ingress path of a 802.1Q switch to work, the RX
VID of a port needs to be seen as tagged egress on the CPU port.
While configuring the other front-panel ports to be part of this VID,
for bridge scenarios, the untagged flag is applied even on the CPU port
in dsa_switch_vlan_add. This happens because DSA applies the same flags
on the CPU port as on the (bridge-controlled) slave ports, and the
effect in this case is that the CPU port tagged settings get deleted.
Instead of fixing DSA by introducing a way to control VLAN flags on the
CPU port (and hence stop inheriting from the slave ports) - a hard,
perhaps intractable problem - avoid this situation by moving the setup
part of the RX VID on the CPU port after all the other front-panel ports
have been added to the VID.
Fixes: f9bbe4477c30 ("net: dsa: Optional VLAN-based port separation for switches without tagging") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 29 May 2019 19:15:06 +0000 (21:15 +0200)]
r8169: decouple rtl_phy_write_fw from actual driver code
This patch is a further step towards decoupling firmware handling from
the actual driver code. Firmware can be for PHY and/or MAC, and two
pairs of read/write functions are needed for handling PHY firmware and
MAC firmware respectively. Pass these functions via struct rtl_fw and
avoid the ugly switching of mdio_ops behind the back of rtl_writephy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 29 May 2019 18:52:03 +0000 (20:52 +0200)]
r8169: enable WoL speed down on more chip versions
Call the pll power down function also for chip versions 02..06 and
13..15. The MAC can't be powered down on these chip versions, but at
least they benefit from the speed-down power-saving if WoL is enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Wed, 29 May 2019 15:39:41 +0000 (17:39 +0200)]
sctp: deduplicate identical skb_checksum_ops
The same skb_checksum_ops struct is defined twice in two different places,
leading to code duplication. Declare it as a global variable into a common
header instead of allocating it on the stack on each function call.
bloat-o-meter reports a slight code shrink.
Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Matteo Croce <mcroce@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Wed, 29 May 2019 15:13:48 +0000 (17:13 +0200)]
net: avoid indirect calls in L4 checksum calculation
Commit 283c16a2dfd3 ("indirect call wrappers: helpers to speed-up
indirect calls of builtin") introduces some macros to avoid doing
indirect calls.
Use these helpers to remove two indirect calls in the L4 checksum
calculation for devices which don't have hardware support for it.
As a test I generate packets with pktgen out to a dummy interface
with HW checksumming disabled, to have the checksum calculated in
every sent packet.
The packet rate measured with an i7-6700K CPU and a single pktgen
thread raised from 6143 to 6608 Kpps, an increase by 7.5%
Suggested-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 29 May 2019 14:34:32 +0000 (22:34 +0800)]
net: dsa: sja1105: Make static_config_check_memory_size static
Fix sparse warning:
drivers/net/dsa/sja1105/sja1105_static_config.c:446:1: warning:
symbol 'static_config_check_memory_size' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Wed, 29 May 2019 13:59:48 +0000 (15:59 +0200)]
net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue value
MVPP2_TXQ_SCHED_TOKEN_CNTR_REG() expects the logical queue id but
the current code is passing the global tx queue offset, so it ends
up writing to unknown registers (between 0x8280 and 0x82fc, which
seemed to be unused by the hardware). This fixes the issue by using
the logical queue id instead.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
connection tracking support for bridge
This patchset adds native connection tracking support for the bridge.
Patch #1 and #2 extract code from IPv4/IPv6 fragmentation core and
introduce the fraglist splitter. That splits a skbuff fraglist into
independent fragments.
Patch #3 and #4 also extract code from IPv4/IPv6 fragmentation core
and introduce the skbuff into fragments transformer. This can be used
by linearized skbuffs (eg. coming from nfqueue and ct helpers) as well
as cloned skbuffs (that are either seen either with taps or with bridge
port flooding).
Patch #5 moves the specific IPCB() code from these new fragment
splitter/transformer APIs into the IPv4 stack. The bridge has a
different control buffer layout and it starts using this new APIs in
this patchset.
Patch #6 adds basic infrastructure that allows to register bridge
conntrack support.
Patch #7 adds bridge conntrack support (only for IPv4 in this patch).
Patch #8 adds IPv6 support for the bridge conntrack support.
Patch #9 registers the IPv4/IPv6 conntrack hooks in case the bridge
conntrack is used to deal with local traffic, ie. prerouting -> input
bridge hook path. This cover the bridge interface has a IP address
scenario.
Before this patchset, only chance for people to do stateful filtering is
to use the `br_netfilter` emulation layer, that turns bridge frame into
IPv4/IPv6 packets and inject them into the IPv4/IPv6 hooks. Apparently,
this module allows users to use iptables and all of its feature-set from
the bridge, including stateful filtering. However, this approach is
flawed in many aspects that have been discussed many times. This is a
step forward to deprecate `br_netfilter'.
v2: Fix English typo in commit message.
v3: Fix another English typo in commit message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_conntrack_bridge: register inet conntrack for bridge
This patch enables IPv4 and IPv6 conntrack from the bridge to deal with
local traffic. Hence, packets that are passed up to the local input path
are confirmed later on from the {ipv4,ipv6}_confirm() hooks.
For packets leaving the IP stack (ie. output path), fragmentation occurs
after the inet postrouting hook. Therefore, the bridge local out and
postrouting bridge hooks see fragments with conntrack objects, which is
inconsistent. In this case, we could defragment again from the bridge
output hook, but this is expensive. The recommended filtering spot for
outgoing locally generated traffic leaving through the bridge interface
is to use the classic IPv4/IPv6 output hook, which comes earlier.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic connection tracking support for the bridge,
including initial IPv4 support.
This patch register two hooks to deal with the bridge forwarding path,
one from the bridge prerouting hook to call nf_conntrack_in(); and
another from the bridge postrouting hook to confirm the entry.
The conntrack bridge prerouting hook defragments packets before passing
them to nf_conntrack_in() to look up for an existing entry, otherwise a
new entry is allocated and it is attached to the skbuff. The conntrack
bridge postrouting hook confirms new conntrack entries, ie. if this is
the first packet seen, then it adds the entry to the hashtable and (if
needed) it refragments the skbuff into the original fragments, leaving
the geometry as is if possible. Exceptions are linearized skbuffs, eg.
skbuffs that are passed up to nfqueue and conntrack helpers, as well as
cloned skbuff for the local delivery (eg. tcpdump), also in case of
bridge port flooding (cloned skbuff too).
The packet defragmentation is done through the ip_defrag() call. This
forces us to save the bridge control buffer, reset the IP control buffer
area and then restore it after call. This function also bumps the IP
fragmentation statistics, it would be probably desiderable to have
independent statistics for the bridge defragmentation/refragmentation.
The maximum fragment length is stored in the control buffer and it is
used to refragment the skbuff from the postrouting path.
The new fraglist splitter and fragment transformer APIs are used to
implement the bridge refragmentation code. The br_ip_fragment() function
drops the packet in case the maximum fragment size seen is larger than
the output port MTU.
This patchset follows the principle that conntrack should not drop
packets, so users can do it through policy via invalid state matching.
Like br_netfilter, there is no refragmentation for packets that are
passed up for local delivery, ie. prerouting -> input path. There are
calls to nf_reset() already in several spots in the stack since time ago
already, eg. af_packet, that show that skbuff fraglist handling from the
netif_rx path is supported already.
The helpers are called from the postrouting hook, before confirmation,
from there we may see packet floods to bridge ports. Then, although
unlikely, this may result in exercising the helpers many times for each
clone. It would be good to explore how to pass all the packets in a list
to the conntrack hook to do this handle only once for this case.
Thanks to Florian Westphal for handing me over an initial patchset
version to add support for conntrack bridge.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_conntrack: allow to register bridge support
This patch adds infrastructure to register and to unregister bridge
support for the conntrack module via nf_ct_bridge_register() and
nf_ct_bridge_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipv6: split skbuff into fragments transformer
This patch exposes a new API to refragment a skbuff. This allows you to
split either a linear skbuff or to force the refragmentation of an
existing fraglist using a different mtu. The API consists of:
* ip6_frag_init(), that initializes the internal state of the transformer.
* ip6_frag_next(), that allows you to fetch the next fragment. This function
internally allocates the skbuff that represents the fragment, it pushes
the IPv6 header, and it also copies the payload for each fragment.
The ip6_frag_state object stores the internal state of the splitter.
This code has been extracted from ip6_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipv4: split skbuff into fragments transformer
This patch exposes a new API to refragment a skbuff. This allows you to
split either a linear skbuff or to force the refragmentation of an
existing fraglist using a different mtu. The API consists of:
* ip_frag_init(), that initializes the internal state of the transformer.
* ip_frag_next(), that allows you to fetch the next fragment. This function
internally allocates the skbuff that represents the fragment, it pushes
the IPv4 header, and it also copies the payload for each fragment.
The ip_frag_state object stores the internal state of the splitter.
This code has been extracted from ip_do_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the skbuff fraglist split iterator. This API provides an
iterator to transform the fraglist into single skbuff objects, it
consists of:
* ip6_fraglist_init(), that initializes the internal state of the
fraglist iterator.
* ip6_fraglist_prepare(), that restores the IPv6 header on the fragment.
* ip6_fraglist_next(), that retrieves the fragment from the fraglist and
updates the internal state of the iterator to point to the next
fragment in the fraglist.
The ip6_fraglist_iter object stores the internal state of the iterator.
This code has been extracted from ip6_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the skbuff fraglist splitter. This API provides an
iterator to transform the fraglist into single skbuff objects, it
consists of:
* ip_fraglist_init(), that initializes the internal state of the
fraglist splitter.
* ip_fraglist_prepare(), that restores the IPv4 header on the
fragments.
* ip_fraglist_next(), that retrieves the fragment from the fraglist and
it updates the internal state of the splitter to point to the next
fragment skbuff in the fraglist.
The ip_fraglist_iter object stores the internal state of the iterator.
This code has been extracted from ip_do_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 30 May 2019 20:41:26 +0000 (13:41 -0700)]
Merge branch 'add-TFO-backup-key'
Jason Baron says:
====================
add TFO backup key
Christoph, Igor, and I have worked on an API that facilitates TFO key
rotation. This is a follow up to the series that Christoph previously
posted, with an API that meets both of our use-cases. Here's a
link to the previous work:
https://patchwork.ozlabs.org/cover/1013753/
Changes in v2:
-spelling fixes in ip-sysctl.txt (Jeremy Sowden)
-re-base to latest net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Baron [Wed, 29 May 2019 16:34:01 +0000 (12:34 -0400)]
selftests/net: add TFO key rotation selftest
Demonstrate how the primary and backup TFO keys can be rotated while
minimizing the number of client cookies that are rejected.
Signed-off-by: Jason Baron <jbaron@akamai.com> Signed-off-by: Christoph Paasch <cpaasch@apple.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jason Baron <jbaron@akamai.com> Signed-off-by: Christoph Paasch <cpaasch@apple.com> Cc: Jeremy Sowden <jeremy@azazel.net> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log