Ziyang Xuan [Fri, 11 Nov 2022 07:09:35 +0000 (15:09 +0800)]
octeon_ep: ensure get mac address successfully before eth_hw_addr_set()
octep_get_mac_addr() can fail because send mbox message failed. If this
happens, octep_dev->mac_addr will be zero. It should not continue to
initialize. Add exception handling for octep_get_mac_addr() to fix it.
Fixes: 2214a12665a2 ("octeon_ep: Add driver framework and device initialization") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ziyang Xuan [Fri, 11 Nov 2022 07:09:23 +0000 (15:09 +0800)]
octeon_ep: fix potential memory leak in octep_device_setup()
When occur unsupported_dev and mbox init errors, it did not free oct->conf
and iounmap() oct->mmio[i].hw_addr. That would trigger memory leak problem.
Add kfree() for oct->conf and iounmap() for oct->mmio[i].hw_addr under
unsupported_dev and mbox init errors to fix the problem.
Fixes: 2214a12665a2 ("octeon_ep: Add driver framework and device initialization") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ziyang Xuan [Fri, 11 Nov 2022 07:08:47 +0000 (15:08 +0800)]
octeon_ep: ensure octep_get_link_status() successfully before octep_link_up()
octep_get_link_status() can fail because send mbox message failed, then
octep_get_link_status() will return ret less than 0. Excute octep_link_up()
as long as ret is not equal to 0 in octep_open() now. That is not correct.
The value type of link.state is enum octep_ctrl_net_state. Positive value
represents up. Excute octep_link_up() when ret is bigger than 0.
Fixes: 2214a12665a2 ("octeon_ep: Add driver framework and device initialization") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ziyang Xuan [Fri, 11 Nov 2022 07:08:27 +0000 (15:08 +0800)]
octeon_ep: delete unnecessary napi rollback under set_queues_err in octep_open()
octep_napi_add() and octep_napi_enable() are all after
netif_set_real_num_{tx,rx}_queues() in octep_open(), so it is unnecessary
napi rollback under set_queues_err. Delete them to fix it.
Fixes: 5679af3ca2cb ("octeon_ep: add Tx/Rx processing and interrupt support") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gaosheng Cui [Fri, 11 Nov 2022 07:04:33 +0000 (15:04 +0800)]
bnxt_en: Remove debugfs when pci_register_driver failed
When pci_register_driver failed, we need to remove debugfs,
which will caused a resource leak, fix it.
Resource leak logs as follows:
[ 52.184456] debugfs: Directory 'bnxt_en' with parent '/' already present!
Fixes: 57aece0f11d7 ("bnxt_en: add debugfs support for DIM") Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao [Fri, 11 Nov 2022 01:47:34 +0000 (09:47 +0800)]
net: caif: fix double disconnect client in chnl_net_open()
When connecting to client timeout, disconnect client for twice in
chnl_net_open(). Remove one. Compile tested only.
Fixes: 29db29f3a202 ("caif: Use link layer MTU instead of fixed MTU") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chuang Wang [Fri, 11 Nov 2022 01:41:30 +0000 (09:41 +0800)]
net: macvlan: Use built-in RCU list checking
hlist_for_each_entry_rcu() has built-in RCU and lock checking.
Pass cond argument to hlist_for_each_entry_rcu() to silence false
lockdep warning when CONFIG_PROVE_RCU_LIST is enabled.
Execute as follow:
ip link add link eth0 type macvlan mode source macaddr add <MAC-ADDR>
The rtnl_lock is held when macvlan_hash_lookup_source() or
macvlan_fill_info_macaddr() are called in the non-RCU read side section.
So, pass lockdep_rtnl_is_held() to silence false lockdep warning.
Fixes: fe178a01da16 ("macvlan: add source mode") Signed-off-by: Chuang Wang <nashuiliang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang ShaoBo [Thu, 10 Nov 2022 11:38:23 +0000 (19:38 +0800)]
mISDN: fix misuse of put_device() in mISDN_register_device()
We should not release reference by put_device() before calling device_initialize().
Fixes: 0dbf43dff27e ("mISDN: fix possible memory leak in mISDN_register_device()") Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengchao Shao [Thu, 10 Nov 2022 10:30:37 +0000 (18:30 +0800)]
net: liquidio: release resources when liquidio driver open failed
When liquidio driver open failed, it doesn't release resources. Compile
tested only.
Fixes: d9ca5fc64441 ("liquidio: MSIX support for CN23XX") Fixes: 9309c48cc96d ("net: liquidio: Add missing null pointer checks") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We're currently hitting the WARN_ON in mctp_i2c_flow_release:
if (midev->release_count > midev->i2c_lock_count) {
WARN_ONCE(1, "release count overflow");
This may be hit if we expire a flow before sending the first packet it
contains - as we will not be pairing the increment of release_count
(performed on flow release) with the i2c lock operation (only
performed on actual TX).
To fix this, only release a flow if we've encountered it previously (ie,
dev_flow_state does not indicate NEW), as we will mark the flow as
ACTIVE at the same time as accounting for the i2c lock operation. We
also need to add an INVALID flow state, to indicate when we've done the
release.
Yu Liao [Thu, 10 Nov 2022 09:03:29 +0000 (17:03 +0800)]
net/tls: Fix memory leak in tls_enc_skb() and tls_sw_fallback_init()
'aead_req' and 'aead_send' is allocated but not freed in default switch
case. This commit fixes the potential memory leak by freeing them under
the situation.
Note that the default cases here should never be reached as they'd
mean we allowed offloading an unsupported algorithm.
net: stmmac: ensure tx function is not running in stmmac_xdp_release()
When stmmac_xdp_release() is called, there is a possibility that tx
function is still running on other queues which will lead to tx queue
timed out and reset adapter.
This commit ensure that tx function is not running xdp before release
flow continue to run.
Fixes: 507e17e530ce ("net: stmmac: enhance XDP ZC driver level switching performance") Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com> Signed-off-by: Mohd Faizal Abdul Rahim <faizal.abdul.rahim@intel.com> Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com> Link: https://lore.kernel.org/r/20221110064552.22504-1-noor.azura.ahmad.tarmizi@linux.intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: phy: dp83867: Fix SGMII FIFO depth for non OF devices
Current driver code will read device tree node information,
and set default values if there is no info provided.
This is not done in non-OF devices leading to SGMII fifo depths being
set to the smallest size.
This patch sets the value to the default value of the PHY as stated in the
PHY datasheet.
Fixes: 8c1f72d9aba0 ("net: phy: dp83867: introduce critical chip default init for non-of platform") Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20221110054938.925347-1-michael.wei.hong.sit@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yuan Can [Thu, 10 Nov 2022 02:16:42 +0000 (02:16 +0000)]
net: hinic: Fix error handling in hinic_module_init()
A problem about hinic create debugfs failed is triggered with the
following log given:
[ 931.419023] debugfs: Directory 'hinic' with parent '/' already present!
The reason is that hinic_module_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of hinic can never be created later.
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: 4bde46ad134c ("hinic: add support to query sq info") Signed-off-by: Yuan Can <yuancan@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20221110021642.80378-1-yuancan@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yang Yingliang [Wed, 9 Nov 2022 13:28:32 +0000 (21:28 +0800)]
mISDN: fix possible memory leak in mISDN_dsp_element_register()
Afer commit 13e0419aca34 ("driver core: get rid of struct device's
bus_id string array"), the name of device is allocated dynamically,
use put_device() to give up the reference, so that the name can be
freed in kobject_cleanup() when the refcount is 0.
The 'entry' is going to be freed in mISDN_dsp_dev_release(), so the
kfree() is removed. list_del() is called in mISDN_dsp_dev_release(),
so it need be initialized.
Wei Yongjun [Wed, 9 Nov 2022 15:01:36 +0000 (15:01 +0000)]
net: bgmac: Drop free_netdev() from bgmac_enet_remove()
netdev is allocated in bgmac_alloc() with devm_alloc_etherdev() and will
be auto released in ->remove and ->probe failure path. Using free_netdev()
in bgmac_enet_remove() leads to double free.
We've added 11 non-merge commits during the last 8 day(s) which contain
a total of 11 files changed, 83 insertions(+), 74 deletions(-).
The main changes are:
1) Fix strncpy_from_kernel_nofault() to prevent out-of-bounds writes,
from Alban Crequy.
2) Fix for bpf_prog_test_run_skb() to prevent wrong alignment,
from Baisong Zhong.
3) Switch BPF_DISPATCHER to static_call() instead of ftrace infra, with
a small build fix on top, from Peter Zijlstra and Nathan Chancellor.
4) Fix memory leak in BPF verifier in some error cases, from Wang Yufen.
5) 32-bit compilation error fixes for BPF selftests, from Pu Lehui and
Yang Jihong.
6) Ensure even distribution of per-CPU free list elements, from Xu Kuohai.
7) Fix copy_map_value() to track special zeroed out areas properly,
from Xu Kuohai.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Fix offset calculation error in __copy_map_value and zero_map_value
bpf: Initialize same number of free nodes for each pcpu_freelist
selftests: bpf: Add a test when bpf_probe_read_kernel_str() returns EFAULT
maccess: Fix writing offset in case of fault in strncpy_from_kernel_nofault()
selftests/bpf: Fix test_progs compilation failure in 32-bit arch
selftests/bpf: Fix casting error when cross-compiling test_verifier for 32-bit platforms
bpf: Fix memory leaks in __check_func_call
bpf: Add explicit cast to 'void *' for __BPF_DISPATCHER_UPDATE()
bpf: Convert BPF_DISPATCHER to use static_call() (not ftrace)
bpf: Revert ("Fix dispatcher patchable function entry to 5 bytes nop")
bpf, test_run: Fix alignment problem in bpf_prog_test_run_skb()
====================
Xu Kuohai [Thu, 10 Nov 2022 12:21:28 +0000 (07:21 -0500)]
bpf: Initialize same number of free nodes for each pcpu_freelist
pcpu_freelist_populate() initializes nr_elems / num_possible_cpus() + 1
free nodes for some CPUs, and then possibly one CPU with fewer nodes,
followed by remaining cpus with 0 nodes. For example, when nr_elems == 256
and num_possible_cpus() == 32, CPU 0~27 each gets 9 free nodes, CPU 28 gets
4 free nodes, CPU 29~31 get 0 free nodes, while in fact each CPU should get
8 nodes equally.
This patch initializes nr_elems / num_possible_cpus() free nodes for each
CPU firstly, then allocates the remaining free nodes by one for each CPU
until no free nodes left.
Alban Crequy [Thu, 10 Nov 2022 08:56:14 +0000 (09:56 +0100)]
selftests: bpf: Add a test when bpf_probe_read_kernel_str() returns EFAULT
This commit tests previous fix of bpf_probe_read_kernel_str().
The BPF helper bpf_probe_read_kernel_str should return -EFAULT when
given a bad source pointer and the target buffer should only be modified
to make the string NULL terminated.
bpf_probe_read_kernel_str() was previously inserting a NULL before the
beginning of the dst buffer. This test should ensure that the
implementation stays correct for now on.
Without the fix, this test will fail as follows:
$ cd tools/testing/selftests/bpf
$ make
$ sudo ./test_progs --name=varlen
...
test_varlen:FAIL:check got 0 != exp 66
Signed-off-by: Alban Crequy <albancrequy@linux.microsoft.com> Signed-off-by: Francis Laniel <flaniel@linux.microsoft.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20221110085614.111213-3-albancrequy@linux.microsoft.com
Changes v1 to v2:
- add ack tag
- fix my email
- rebase on bpf tree and tag for bpf tree
Alban Crequy [Thu, 10 Nov 2022 08:56:13 +0000 (09:56 +0100)]
maccess: Fix writing offset in case of fault in strncpy_from_kernel_nofault()
If a page fault occurs while copying the first byte, this function resets one
byte before dst.
As a consequence, an address could be modified and leaded to kernel crashes if
case the modified address was accessed later.
Fixes: 2d1a6c4da567 ("maccess: allow architectures to provide kernel probing directly") Signed-off-by: Alban Crequy <albancrequy@linux.microsoft.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Tested-by: Francis Laniel <flaniel@linux.microsoft.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: <stable@vger.kernel.org> [5.8] Link: https://lore.kernel.org/bpf/20221110085614.111213-2-albancrequy@linux.microsoft.com
Jaco Coetzee [Wed, 9 Nov 2022 20:27:57 +0000 (15:27 -0500)]
nfp: change eeprom length to max length enumerators
Extend the size of QSFP EEPROM for types SSF8436 and SFF8636
from 256 to 640 bytes in order to expose all the EEPROM pages by
ethtool.
For SFF-8636 and SFF-8436 specifications, the driver exposes
256 bytes of EEPROM data for ethtool's get_module_eeprom()
callback, resulting in "netlink error: Invalid argument" when
an EEPROM read with an offset larger than 256 bytes is attempted.
Changing the length enumerators to the _MAX_LEN
variants exposes all 640 bytes of the EEPROM allowing upper
pages 1, 2 and 3 to be read.
Fixes: b5507ae3616e ("ethtool: Add fallback to get_module_eeprom from netlink command") Signed-off-by: Jaco Coetzee <jaco.coetzee@corigine.com> Reviewed-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 11 Nov 2022 01:31:15 +0000 (17:31 -0800)]
Merge tag 'net-6.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter, wifi, can and bpf.
Current release - new code bugs:
- can: af_can: can_exit(): add missing dev_remove_pack() of
canxl_packet
Previous releases - regressions:
- bpf, sockmap: fix the sk->sk_forward_alloc warning
- wifi: mac80211: fix general-protection-fault in
ieee80211_subif_start_xmit()
- can: af_can: fix NULL pointer dereference in can_rx_register()
- can: dev: fix skb drop check, avoid o-o-b access
- nfnetlink: fix potential dead lock in nfnetlink_rcv_msg()
Previous releases - always broken:
- bpf: fix wrong reg type conversion in release_reference()
- gso: fix panic on frag_list with mixed head alloc types
- wifi: brcmfmac: fix buffer overflow in brcmf_fweh_event_worker()
- wifi: mac80211: set TWT Information Frame Disabled bit as 1
- eth: macsec offload related fixes, make sure to clear the keys from
memory
- tun: fix memory leaks in the use of napi_get_frags
- tun: call napi_schedule_prep() to ensure we own a napi
- tcp: prohibit TCP_REPAIR_OPTIONS if data was already sent
- ipv6: addrlabel: fix infoleak when sending struct ifaddrlblmsg to
network
- tipc: fix a msg->req tlv length check
- sctp: clear out_curr if all frag chunks of current msg are pruned,
avoid list corruption
- mctp: fix an error handling path in mctp_init(), avoid leaks"
* tag 'net-6.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
eth: sp7021: drop free_netdev() from spl2sw_init_netdev()
MAINTAINERS: Move Vivien to CREDITS
net: macvlan: fix memory leaks of macvlan_common_newlink
ethernet: tundra: free irq when alloc ring failed in tsi108_open()
net: mv643xx_eth: disable napi when init rxq or txq failed in mv643xx_eth_open()
ethernet: s2io: disable napi when start nic failed in s2io_card_up()
net: atlantic: macsec: clear encryption keys from the stack
net: phy: mscc: macsec: clear encryption keys when freeing a flow
stmmac: dwmac-loongson: fix missing of_node_put() while module exiting
stmmac: dwmac-loongson: fix missing pci_disable_device() in loongson_dwmac_probe()
stmmac: dwmac-loongson: fix missing pci_disable_msi() while module exiting
cxgb4vf: shut down the adapter when t4vf_update_port_info() failed in cxgb4vf_open()
mctp: Fix an error handling path in mctp_init()
stmmac: intel: Update PCH PTP clock rate from 200MHz to 204.8MHz
net: cxgb3_main: disable napi when bind qsets failed in cxgb_up()
net: cpsw: disable napi in cpsw_ndo_open()
iavf: Fix VF driver counting VLAN 0 filters
ice: Fix spurious interrupt during removal of trusted VF
net/mlx5e: TC, Fix slab-out-of-bounds in parse_tc_actions
net/mlx5e: E-Switch, Fix comparing termination table instance
...
Jakub Kicinski [Fri, 11 Nov 2022 00:29:56 +0000 (16:29 -0800)]
Merge tag 'mlx5-fixes-2022-11-09' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-11-02
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2022-11-09' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: TC, Fix slab-out-of-bounds in parse_tc_actions
net/mlx5e: E-Switch, Fix comparing termination table instance
net/mlx5e: TC, Fix wrong rejection of packet-per-second policing
net/mlx5e: Fix tc acts array not to be dependent on enum order
net/mlx5e: Fix usage of DMA sync API
net/mlx5e: Add missing sanity checks for max TX WQE size
net/mlx5: fw_reset: Don't try to load device in case PCI isn't working
net/mlx5: E-switch, Set to legacy mode if failed to change switchdev mode
net/mlx5: Allow async trigger completion execution on single CPU systems
net/mlx5: Bridge, verify LAG state when adding bond to bridge
====================
Linus Torvalds [Thu, 10 Nov 2022 16:58:29 +0000 (08:58 -0800)]
Merge tag 'for-6.1-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- revert memory optimization for scrub blocks, this misses errors in
2nd and following blocks
- add exception for ENOMEM as reason for transaction abort to not print
stack trace, syzbot has reported many
- zoned fixes:
- fix locking imbalance during scrub
- initialize zones for seeding device
- initialize zones for cloned device structures
- when looking up device, change assertion to a real check as some of
the search parameters can be passed by ioctl, reported by syzbot
- fix error pointer check in self tests
* tag 'for-6.1-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: fix locking imbalance on scrub
btrfs: zoned: initialize device's zone info for seeding
btrfs: zoned: clone zoned device info when cloning a device
Revert "btrfs: scrub: use larger block size for data extent scrub"
btrfs: don't print stack trace when transaction is aborted due to ENOMEM
btrfs: selftests: fix wrong error check in btrfs_free_dummy_root()
btrfs: fix match incorrectly in dev_args_match_device
Linus Torvalds [Thu, 10 Nov 2022 16:42:59 +0000 (08:42 -0800)]
Merge tag 'soundwire-6.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire fixes from Vinod Koul:
"Two qcom driver fixes for broadcast completion reinit and check for
outanding writes. And a lone Intel driver fix for clock stop timeout"
* tag 'soundwire-6.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: qcom: check for outanding writes before doing a read
soundwire: qcom: reinit broadcast completion
soundwire: intel: Initialize clock stop timeout
Linus Torvalds [Thu, 10 Nov 2022 16:36:42 +0000 (08:36 -0800)]
Merge tag 'phy-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy fixes from Vinod Koul:
"A bunch of odd driver fixes and a MAINTAINER email update:
- Update Kishon's email
- stms32 error code fix in driver probe
- tegra: fix for checking valid pointer
- qcom_qmp: null deref fix
- sunplus: error check fix
- ralink: add missing sentinel to table"
* tag 'phy-fixes-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: ralink: mt7621-pci: add sentinel to quirks table
phy: sunplus: Fix an IS_ERR() vs NULL bug in sp_usb_phy_probe
phy: qcom-qmp-combo: fix NULL-deref on runtime resume
phy: tegra: xusb: Fix crash during pad power on/down
phy: stm32: fix an error code in probe
MAINTAINERS: Update Kishon's email address in GENERIC PHY FRAMEWORK
Linus Torvalds [Thu, 10 Nov 2022 16:28:20 +0000 (08:28 -0800)]
Merge tag 'hwlock-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull hwspinlock updates from Bjorn Andersson:
"I apparently had missed tagging and sending this set of changes out
during the 6.1 merge window. But did get the associated dts changes
depending on this merged. The result is a regression in 6.1-rc on the
affected, older, Qualcomm platforms - in for form of them not booting.
So while these weren't regression fixes originally, they are now. It's
not introducing new beahavior, but simply extending the existing new
Devicetree model, to cover remaining platforms:
- extend the DeviceTree binding and implementation for the Qualcomm
hardware spinlock on some older platforms to follow the style of
the newer ones where the DeviceTree representation does not rely on
an intermediate syscon node"
* tag 'hwlock-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
dt-bindings: hwlock: qcom-hwspinlock: add syscon to MSM8974
hwspinlock: qcom: add support for MMIO on older SoCs
hwspinlock: qcom: correct MMIO max register for newer SoCs
dt-bindings: hwlock: qcom-hwspinlock: correct example indentation
dt-bindings: hwlock: qcom-hwspinlock: add support for MMIO on older SoCs
In the scenario where the macvlan mode is configured as 'source',
macvlan_changelink_sources() will be execured to reconfigure list of
remote source mac addresses, at the same time, if register_netdevice()
return an error, the resource generated by macvlan_changelink_sources()
is not cleaned up.
Using this patch, in the case of an error, it will execute
macvlan_flush_sources() to ensure that the resource is cleaned up.
Zhengchao Shao [Wed, 9 Nov 2022 02:54:32 +0000 (10:54 +0800)]
net: mv643xx_eth: disable napi when init rxq or txq failed in mv643xx_eth_open()
When failed to init rxq or txq in mv643xx_eth_open() for opening device,
napi isn't disabled. When open mv643xx_eth device next time, it will
trigger a BUG_ON() in napi_enable(). Compile tested only.
Zhengchao Shao [Wed, 9 Nov 2022 02:37:41 +0000 (10:37 +0800)]
ethernet: s2io: disable napi when start nic failed in s2io_card_up()
When failed to start nic or add interrupt service routine in
s2io_card_up() for opening device, napi isn't disabled. When open
s2io device next time, it will trigger a BUG_ON()in napi_enable().
Compile tested only.
====================
macsec: clear encryption keys in h/w drivers
Commit 5d6d7cda5f0c ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading but some h/w drivers did a copy of the key
which need to be zeroed as well.
The MSCC PHY driver can actually be converted not to copy the encryption
key at all, but such patch would be quite difficult to backport. I'll
send a following up patch doing this in net-next once this series lands.
Tested on the MSCC PHY but not on the atlantic NIC.
====================
Antoine Tenart [Tue, 8 Nov 2022 15:34:59 +0000 (16:34 +0100)]
net: atlantic: macsec: clear encryption keys from the stack
Commit 5d6d7cda5f0c ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading, but the atlantic driver made a copy and did
not clear it. Fix this.
[4 Fixes tags below, all part of the same series, no need to split this]
Antoine Tenart [Tue, 8 Nov 2022 15:34:58 +0000 (16:34 +0100)]
net: phy: mscc: macsec: clear encryption keys when freeing a flow
Commit 5d6d7cda5f0c ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading, but the MSCC PHY driver made a copy, kept
it in the flow data and did not clear it when freeing a flow. Fix this.
Fixes: f999521bdebb ("net: phy: mscc: macsec support") Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
====================
stmmac: dwmac-loongson: fixes three leaks
patch #2 fixes missing pci_disable_device() in the error path in probe()
patch #1 and pach #3 fix missing pci_disable_msi() and of_node_put() in
error and remove() path.
====================
Yang Yingliang [Tue, 8 Nov 2022 11:46:47 +0000 (19:46 +0800)]
stmmac: dwmac-loongson: fix missing of_node_put() while module exiting
The node returned by of_get_child_by_name() with refcount decremented,
of_node_put() needs be called when finish using it. So add it in the
error path in loongson_dwmac_probe() and in loongson_dwmac_remove().
Fixes: 5427f2ee3137 ("stmmac: dwmac-loongson: fix invalid mdio_node") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Yang Yingliang [Tue, 8 Nov 2022 11:46:46 +0000 (19:46 +0800)]
stmmac: dwmac-loongson: fix missing pci_disable_device() in loongson_dwmac_probe()
Add missing pci_disable_device() in the error path in loongson_dwmac_probe().
Fixes: 8faa7848cdb4 ("stmmac: pci: Add dwmac support for Loongson") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Yang Yingliang [Tue, 8 Nov 2022 11:46:45 +0000 (19:46 +0800)]
stmmac: dwmac-loongson: fix missing pci_disable_msi() while module exiting
pci_enable_msi() has been called in loongson_dwmac_probe(),
so pci_disable_msi() needs be called in remove path and error
path of probe().
Fixes: 8faa7848cdb4 ("stmmac: pci: Add dwmac support for Loongson") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Zhengchao Shao [Wed, 9 Nov 2022 01:21:00 +0000 (09:21 +0800)]
cxgb4vf: shut down the adapter when t4vf_update_port_info() failed in cxgb4vf_open()
When t4vf_update_port_info() failed in cxgb4vf_open(), resources applied
during adapter goes up are not cleared. Fix it. Only be compiled, not be
tested.
Tan, Tee Min [Tue, 8 Nov 2022 02:08:11 +0000 (21:08 -0500)]
stmmac: intel: Update PCH PTP clock rate from 200MHz to 204.8MHz
Current Intel platform has an output of ~976ms interval
when probed on 1 Pulse-per-Second(PPS) hardware pin.
The correct PTP clock frequency for PCH GbE should be 204.8MHz
instead of 200MHz. PSE GbE PTP clock rate remains at 200MHz.
Fixes: 300c10cdd817 ("net: stmmac: create dwmac-intel.c to contain all Intel platform") Signed-off-by: Ling Pei Lee <pei.lee.ling@intel.com> Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com> Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: Gan Yi Fang <yi.fang.gan@intel.com> Link: https://lore.kernel.org/r/20221108020811.12919-1-yi.fang.gan@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao [Wed, 9 Nov 2022 02:14:51 +0000 (10:14 +0800)]
net: cxgb3_main: disable napi when bind qsets failed in cxgb_up()
When failed to bind qsets in cxgb_up() for opening device, napi isn't
disabled. When open cxgb3 device next time, it will trigger a BUG_ON()
in napi_enable(). Compile tested only.
Zhengchao Shao [Wed, 9 Nov 2022 01:15:37 +0000 (09:15 +0800)]
net: cpsw: disable napi in cpsw_ndo_open()
When failed to create xdp rxqs or fill rx channels in cpsw_ndo_open() for
opening device, napi isn't disabled. When open cpsw device next time, it
will report a invalid opcode issue. Compiled tested only.
Michal Jaron [Fri, 14 Oct 2022 08:45:37 +0000 (10:45 +0200)]
iavf: Fix VF driver counting VLAN 0 filters
VF driver mistakenly counts VLAN 0 filters, when no PF driver
counts them.
Do not count VLAN 0 filters, when VLAN_V2 is engaged.
Counting those filters in, will affect filters size by -1, when
sending batched VLAN addition message.
Fixes: 00818fbb85a7 ("iavf: Fix VLAN_V2 addition/rejection") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Norbert Zulinski [Mon, 10 Oct 2022 14:22:22 +0000 (10:22 -0400)]
ice: Fix spurious interrupt during removal of trusted VF
Previously, during removal of trusted VF when VF is down there was
number of spurious interrupt equal to number of queues on VF.
Add check if VF already has inactive queues. If VF is disabled and
has inactive rx queues then do not disable rx queues.
Add check in ice_vsi_stop_tx_ring if it's VF's vsi and if VF is
disabled.
Fixes: a0eb944b136c ("ice: Fix memory corruption in VF driver") Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Linus Torvalds [Wed, 9 Nov 2022 21:07:50 +0000 (13:07 -0800)]
Merge tag 'slab-for-6.1-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fixes from Vlastimil Babka:
"Most are small fixups as described below.
The !CONFIG_TRACING fix is a bit bigger and would normally be done in
the next merge window as part of upcoming hardening changes. But we
realized it can make the kmalloc waste tracking introduced in this
window inaccurate, so decided to go with it now.
Summary:
- Remove !CONFIG_TRACING kmalloc() wrappers intended to save a
function call, due to incompatilibity with recently introduced
wasted space tracking and planned hardening changes.
- A tracing parameter regression fix, by Kees Cook.
- Two kernel-doc warning fixups, by Lukas Bulwahn and myself
* tag 'slab-for-6.1-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
mm, slab: remove duplicate kernel-doc comment for ksize()
mm/slab_common: Restore passing "caller" for tracing
mm/slab: remove !CONFIG_TRACING variants of kmalloc_[node_]trace()
mm/slab_common: repair kernel-doc for __ksize()
Yang Jihong [Tue, 8 Nov 2022 01:58:57 +0000 (09:58 +0800)]
selftests/bpf: Fix test_progs compilation failure in 32-bit arch
test_progs fails to be compiled in the 32-bit arch, log is as follows:
test_progs.c:1013:52: error: format '%ld' expects argument of type 'long int', but argument 3 has type 'size_t' {aka 'unsigned int'} [-Werror=format=]
1013 | sprintf(buf, "MSG_TEST_LOG (cnt: %ld, last: %d)",
| ~~^
| |
| long int
| %d
1014 | strlen(msg->test_log.log_buf),
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| size_t {aka unsigned int}
Fix it.
Fixes: b455de52802f ("selftests/bpf: Add parallelism to test_progs") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/r/20221108015857.132457-1-yangjihong1@huawei.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Pu Lehui [Tue, 8 Nov 2022 12:19:45 +0000 (20:19 +0800)]
selftests/bpf: Fix casting error when cross-compiling test_verifier for 32-bit platforms
When cross-compiling test_verifier for 32-bit platforms, the casting error is shown below:
test_verifier.c:1263:27: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
1263 | info.xlated_prog_insns = (__u64)*buf;
| ^
cc1: all warnings being treated as errors
Fix it by adding zero-extension for it.
Fixes: 8b59aae8407c ("selftests/bpf: specify expected instructions in test_verifier tests") Signed-off-by: Pu Lehui <pulehui@huawei.com> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/r/20221108121945.4104644-1-pulehui@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
The pkt_reformat pointer being saved under flow_act and not
dest attribute in the termination table instance.
Fix the comparison pointers.
Also fix returning success if one pkt_reformat pointer is null
and the other is not.
Fixes: b26bc5fa2f24 ("net/mlx5e: Add support for offloading traffic from uplink to uplink") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Chris Mi <cmi@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
DMA sync functions should use the same direction that was used by DMA
mapping. Use DMA_BIDIRECTIONAL for XDP_TX from regular RQ, which reuses
the same mapping that was used for RX, and DMA_TO_DEVICE for XDP_TX from
XSK RQ and XDP_REDIRECT, which establish a new mapping in this
direction. On the RX side, use the same direction that was used when
setting up the mapping (DMA_BIDIRECTIONAL for XDP, DMA_FROM_DEVICE
otherwise).
Also don't skip sync for device when establishing a DMA_FROM_DEVICE
mapping for RX, as some architectures (ARM) may require invalidating
caches before the device can use the mapping. It doesn't break the
bugfix made in
commit ce34fd2c0855 ("net/mlx5e: Fix page DMA map/unmap attributes"),
since the bug happened on unmap.
net/mlx5e: Add missing sanity checks for max TX WQE size
The commit cited below started using the firmware capability for the
maximum TX WQE size. This commit adds an important check to verify that
the driver doesn't attempt to exceed this capability, and also restores
another check mistakenly removed in the cited commit (a WQE must not
exceed the page size).
Fixes: a81aa439aa53 ("net/mlx5e: Read max WQEBBs on the SQ from firmware") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Chris Mi [Thu, 3 Nov 2022 06:55:39 +0000 (23:55 -0700)]
net/mlx5: E-switch, Set to legacy mode if failed to change switchdev mode
No need to rollback to the other mode because probably will fail
again. Just set to legacy mode and clear fdb table created flag.
So that fdb table will not be cleared again.
Fixes: b4deb7a001e6 ("net/mlx5: E-switch, Remove dependency between sriov and eswitch mode") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Roy Novich [Thu, 3 Nov 2022 06:55:38 +0000 (23:55 -0700)]
net/mlx5: Allow async trigger completion execution on single CPU systems
For a single CPU system, the kernel thread executing mlx5_cmd_flush()
never releases the CPU but calls down_trylock(&cmd→sem) in a busy loop.
On a single processor system, this leads to a deadlock as the kernel
thread which executes mlx5_cmd_invoke() never gets scheduled. Fix this,
by adding the cond_resched() call to the loop, allow the command
completion kernel thread to execute.
Fixes: 1bea202da238 ("net/mlx5: Set command entry semaphore up once got index free") Signed-off-by: Alexander Schmidt <alexschm@de.ibm.com> Signed-off-by: Roy Novich <royno@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Vlad Buslov [Thu, 3 Nov 2022 06:55:37 +0000 (23:55 -0700)]
net/mlx5: Bridge, verify LAG state when adding bond to bridge
Mlx5 LAG is initialized asynchronously on a workqueue which means that for
a brief moment after setting mlx5 UL representors as lower devices of a
bond netdevice the LAG itself is not fully initialized in the driver. When
adding such bond device to a bridge mlx5 bridge code will not consider it
as offload-capable, skip creating necessary bookkeeping and fail any
further bridge offload-related commands with it (setting VLANs, offloading
FDBs, etc.). In order to make the error explicit during bridge
initialization stage implement the code that detects such condition during
NETDEV_PRECHANGEUPPER event and returns an error.
Fixes: 542ca606d80c ("net/mlx5: Bridge, support LAG") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
M Chetan Kumar [Mon, 7 Nov 2022 07:35:24 +0000 (13:05 +0530)]
net: wwan: iosm: fix kernel test robot reported errors
Include linux/vmalloc.h in iosm_ipc_coredump.c &
iosm_ipc_devlink.c to resolve kernel test robot errors.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Mon, 7 Nov 2022 07:35:13 +0000 (13:05 +0530)]
net: wwan: iosm: fix invalid mux header type
Data stall seen during peak DL throughput test & packets are
dropped by mux layer due to invalid header type in datagram.
During initlization Mux aggregration protocol is set to default
UL/DL size and TD count of Mux lite protocol. This configuration
mismatch between device and driver is resulting in data stall/packet
drops.
Override the UL/DL size and TD count for Mux aggregation protocol.
Fixes: 32eea203f830 ("net: wwan: iosm: Enable M.2 7360 WWAN card support") Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Mon, 7 Nov 2022 07:35:02 +0000 (13:05 +0530)]
net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled
With INTEL_IOMMU disable config or by forcing intel_iommu=off from
grub some of the features of IOSM driver like browsing, flashing &
coredump collection is not working.
When driver calls DMA API - dma_map_single() for tx transfers. It is
resulting in dma mapping error.
Set the device DMA addressing capabilities using dma_set_mask() and
remove the INTEL_IOMMU dependency in kconfig so that driver follows
the platform config either INTEL_IOMMU enable or disable.
Fixes: 867964cfe86c ("net: iosm: infrastructure") Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
M Chetan Kumar [Mon, 7 Nov 2022 07:34:49 +0000 (13:04 +0530)]
net: wwan: iosm: fix memory leak in ipc_pcie_read_bios_cfg
ipc_pcie_read_bios_cfg() is using the acpi_evaluate_dsm() to
obtain the wwan power state configuration from BIOS but is
not freeing the acpi_object. The acpi_evaluate_dsm() returned
acpi_object to be freed.
Free the acpi_object after use.
Fixes: 13620cd57f88 ("net: iosm: entry point") Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter [Wed, 9 Nov 2022 09:06:04 +0000 (10:06 +0100)]
selftests: netfilter: Fix and review rpath.sh
Address a few problems with the initial test script version:
* On systems with ip6tables but no ip6tables-legacy, testing for
ip6tables was disabled by accident.
* Firewall setup phase did not respect possibly unavailable tools.
* Consistently call nft via '$nft'.
Fixes: 9e6c67c4ce7c6 ("selftests: netfilter: Test reverse path filtering") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Nick Child [Mon, 7 Nov 2022 20:32:15 +0000 (14:32 -0600)]
ibmveth: Reduce default tx queues to 8
Previously, the default number of transmit queues was 16. Due to
resource concerns, set to 8 queues instead. Still allow the user
to set more queues (max 16) if they like.
Since the driver is virtualized away from the physical NIC, the purpose
of multiple queues is purely to allow for parallel calls to the
hypervisor. Therefore, there is no noticeable effect on performance by
reducing queue count to 8.
Fixes: 5d333412ce7c ("ibmveth: Implement multi queue on xmit") Reported-by: Dave Taht <dave.taht@gmail.com> Signed-off-by: Nick Child <nnac123@linux.ibm.com> Link: https://lore.kernel.org/r/20221107203215.58206-1-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zhengchao Shao [Mon, 7 Nov 2022 10:14:43 +0000 (18:14 +0800)]
net: nixge: disable napi when enable interrupts failed in nixge_open()
When failed to enable interrupts in nixge_open() for opening device,
napi isn't disabled. When open nixge device next time, it will reports
a invalid opcode issue. Fix it. Only be compiled, not be tested.
Jakub Kicinski [Tue, 8 Nov 2022 23:22:33 +0000 (15:22 -0800)]
Merge tag 'linux-can-fixes-for-6.1-20221107' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
can 2022-11-07
The first patch is by Chen Zhongjin and adds a missing
dev_remove_pack() to the AF_CAN protocol.
Zhengchao Shao's patch fixes a potential NULL pointer deref in
AF_CAN's can_rx_register().
The next patch is by Oliver Hartkopp and targets the CAN ISO-TP
protocol, and fixes the state handling for echo TX processing.
Oliver Hartkopp's patch for the j1939 protocol adds a missing
initialization of the CAN headers inside outgoing skbs.
Another patch by Oliver Hartkopp fixes an out of bounds read in the
check for invalid CAN frames in the xmit callback of virtual CAN
devices. This touches all non virtual device drivers as we decided to
rename the function requiring that netdev_priv points to a struct
can_priv.
(Note: This patch will create a merge conflict with net-next where the
pch_can driver has removed.)
The last patch is by Geert Uytterhoeven and adds the missing ECC error
checks for the channels 2-7 in the rcar_canfd driver.
* tag 'linux-can-fixes-for-6.1-20221107' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: rcar_canfd: Add missing ECC error checks for channels 2-7
can: dev: fix skb drop check
can: j1939: j1939_send_one(): fix missing CAN header initialization
can: isotp: fix tx state handling for echo tx processing
can: af_can: fix NULL pointer dereference in can_rx_register()
can: af_can: can_exit(): add missing dev_remove_pack() of canxl_packet
====================
In nf_tables_exit_net(), there is a case where nft_net->commit_list is
empty but nft_net->module_list is not empty. Such a case occurs with
the following scenario:
1. nfnetlink_rcv_batch() is called
2. nf_tables_newset() returns -EAGAIN and NFNL_BATCH_FAILURE bit is
set to status
3. nf_tables_abort() is called with NFNL_ABORT_AUTOLOAD
(nft_net->commit_list is released, but nft_net->module_list is not
because of NFNL_ABORT_AUTOLOAD flag)
4. Jump to replay label
5. netlink_skb_clone() fails and returns from the function (this is
caused by fault injection in the reproducer of syzbot)
This patch fixes this issue by calling __nf_tables_abort() when
nft_net->module_list is not empty in nf_tables_exit_net().
Fixes: f8868eaea4f8 ("netfilter: nf_tables: autoload modules from the abort path") Link: https://syzkaller.appspot.com/bug?id=802aba2422de4218ad0c01b46c9525cc9d4e4aa3 Reported-by: syzbot+178efee9e2d7f87f5103@syzkaller.appspotmail.com Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Signed-off-by: Florian Westphal <fw@strlen.de>
Linus Torvalds [Tue, 8 Nov 2022 20:30:29 +0000 (12:30 -0800)]
Merge tag 'audit-pr-20221107' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"A small audit patch to fix an instance of undefined behavior in a
shift operator caused when shifting a signed value too far, the same
case as the lsm patch merged previously.
While the fix is trivial and I can't imagine it causing a problem in a
backport, I'm not explicitly marking it for stable on the off chance
that there is some system out there which is relying on some wonky
unexpected behavior which this patch could break; *if* it does break,
IMO it's better that to happen in a minor or -rcX release and not in a
stable backport"
* tag 'audit-pr-20221107' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix undefined behavior in bit shift for AUDIT_BIT
Linus Torvalds [Tue, 8 Nov 2022 20:22:02 +0000 (12:22 -0800)]
Merge tag 'lsm-pr-20221107' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull lsm fix from Paul Moore:
"A small capability patch to fix an instance of undefined behavior in a
shift operator caused when shifting a signed value too far.
While the fix is trivial and I can't imagine it causing a problem in a
backport, I'm not explicitly marking it for stable on the off chance
that there is some system out there which is relying on some wonky
unexpected behavior which this patch could break; *if* it does break,
IMO it's better that to happen in a minor or -rcX release and not in a
stable backport"
* tag 'lsm-pr-20221107' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
capabilities: fix undefined behavior in bit shift for CAP_TO_MASK
The root case here is: In function prepare_func_exit(), the callee is
not released in the abnormal scenario after "state->curframe--;". To
fix, move "state->curframe--;" to the very bottom of the function,
right when we free callee and reset frame[] pointer to NULL, as Andrii
suggested.
In addition, function __check_func_call() has a similar problem. In
the abnormal scenario before "state->curframe++;", the callee also
should be released by free_func_state().
Zhengchao Shao [Mon, 7 Nov 2022 04:30:32 +0000 (12:30 +0800)]
drivers: net: xgene: disable napi when register irq failed in xgene_enet_open()
When failed to register irq in xgene_enet_open() for opening device,
napi isn't disabled. When open xgene device next time, it will reports
a invalid opcode issue. Fix it. Only be compiled, not be tested.
Current way of checking available SQE count which is based on
HW updated SQB count could result in driver submitting an SQE
even before CQE for the previously transmitted SQE at the same
index is processed in NAPI resulting losing SKB pointers,
hence a leak. Fix this by checking a consumer index which
is updated once CQE is processed.
Zhengchao Shao [Mon, 7 Nov 2022 01:21:59 +0000 (09:21 +0800)]
net: ethernet: mtk-star-emac: disable napi when connect and start PHY failed in mtk_star_enable()
When failed to connect to and start PHY in mtk_star_enable() for opening
device, napi isn't disabled. When open mtk star device next time, it will
reports a invalid opcode issue. Fix it. Only be compiled, not be tested.
Fixes: e104d92c885f ("net: ethernet: mtk-star-emac: new driver") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20221107012159.211387-1-shaozhengchao@huawei.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Zhengchao Shao [Mon, 7 Nov 2022 01:14:45 +0000 (09:14 +0800)]
net: lapbether: fix issue of invalid opcode in lapbeth_open()
If lapb_register() failed when lapb device goes to up for the first time,
the NAPI is not disabled. As a result, the invalid opcode issue is
reported when the lapb device goes to up for the second time.
====================
sctp: fix a NULL pointer dereference in sctp_sched_dequeue_common
This issue was triggered with SCTP_PR_SCTP_PRIO in sctp,
and caused by not checking and fixing stream->out_curr
after removing a chunk from this stream.
Patch 1 removes an unnecessary check and makes the real
fix easier to add in Patch 2.
====================
and in sctp_sched_fcfs_dequeue() it dequeued a chunk from stream
out_curr outq while this outq was empty.
Normally stream->out_curr must be set to NULL once all frag chunks of
current msg are dequeued, as we can see in sctp_sched_dequeue_done().
However, in sctp_prsctp_prune_unsent() as it is not a proper dequeue,
sctp_sched_dequeue_done() is not called to do this.
This patch is to fix it by simply setting out_curr to NULL when the
last frag chunk of current msg is dequeued from out_curr stream in
sctp_prsctp_prune_unsent().
Xin Long [Fri, 4 Nov 2022 21:45:15 +0000 (17:45 -0400)]
sctp: remove the unnecessary sinfo_stream check in sctp_prsctp_prune_unsent
Since commit d5f9a5945926 ("sctp: introduce stream scheduler foundations"),
sctp_stream_outq_migrate() has been called in sctp_stream_init/update to
removes those chunks to streams higher than the new max. There is no longer
need to do such check in sctp_prsctp_prune_unsent().
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Fri, 4 Nov 2022 20:48:53 +0000 (16:48 -0400)]
tipc: fix the msg->req tlv len check in tipc_nl_compat_name_table_dump_header
This is a follow-up for commit d895b8d851c6 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") where it should have type casted
sizeof(..) to int to work when TLV_GET_DATA_LEN() returns a negative
value.
YueHaibing [Sat, 5 Nov 2022 09:02:45 +0000 (17:02 +0800)]
net: broadcom: Fix BCMGENET Kconfig
While BCMGENET select BROADCOM_PHY as y, but PTP_1588_CLOCK_OPTIONAL is m,
kconfig warning and build errors:
WARNING: unmet direct dependencies detected for BROADCOM_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- BCMGENET [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_BROADCOM [=y] && HAS_IOMEM [=y] && ARCH_BCM2835 [=y]
drivers/net/phy/broadcom.o: In function `bcm54xx_suspend':
broadcom.c:(.text+0x6ac): undefined reference to `bcm_ptp_stop'
drivers/net/phy/broadcom.o: In function `bcm54xx_phy_probe':
broadcom.c:(.text+0x784): undefined reference to `bcm_ptp_probe'
drivers/net/phy/broadcom.o: In function `bcm54xx_config_init':
broadcom.c:(.text+0xd4c): undefined reference to `bcm_ptp_config_init'
Yang Yingliang [Sat, 5 Nov 2022 06:34:42 +0000 (14:34 +0800)]
octeontx2-pf: fix build error when CONFIG_OCTEONTX2_PF=y
If CONFIG_MACSEC=m and CONFIG_OCTEONTX2_PF=y, it leads a build error:
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_pfaf_mbox_up_handler':
otx2_pf.c:(.text+0x181c): undefined reference to `cn10k_handle_mcs_event'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_probe':
otx2_pf.c:(.text+0x437e): undefined reference to `cn10k_mcs_init'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_remove':
otx2_pf.c:(.text+0x5031): undefined reference to `cn10k_mcs_free'
ld: drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.o: in function `otx2_mbox_up_handler_mcs_intr_notify':
otx2_pf.c:(.text+0x5f11): undefined reference to `cn10k_handle_mcs_event'
Make CONFIG_OCTEONTX2_PF depends on CONFIG_MACSEC to fix it. Because
it has empty stub functions of cn10k, CONFIG_OCTEONTX2_PF can be enabled
if CONFIG_MACSEC is disabled
Fixes: 24fdd69c4648 ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20221105063442.2013981-1-yangyingliang@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Miquel Raynal [Fri, 4 Nov 2022 16:21:47 +0000 (17:21 +0100)]
dt-bindings: net: tsnep: Fix typo on generic nvmem property
While working on the nvmem description I figured out this file had the
"nvmem-cell-names" property name misspelled. Fix the typo, as
"nvmem-cells-names" has never existed.
Fixes: 6e0a50b799b2 ("dt-bindings: net: Add tsnep Ethernet controller") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com> Acked-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20221104162147.1288230-1-miquel.raynal@bootlin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are two problems with meson8b_devm_clk_prepare_enable(),
introduced in commit 0b665c4ea65a ("net: stmmac: dwmac-meson8b:
Make the clock enabling code re-usable"):
- It doesn't pass the clk argument, but instead always the
rgmii_tx_clk of the device.
- It silently ignores the return value of devm_add_action_or_reset().
The former didn't become an actual bug until another user showed up in
the next commit d743c50dfd8e ("net: stmmac: dwmac-meson8b: add support
for the RX delay configuration"). The latter means the callers could
end up with the clock not actually prepared/enabled.
Fixes: 0b665c4ea65a ("net: stmmac: dwmac-meson8b: Make the clock enabling code re-usable") Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Link: https://lore.kernel.org/r/20221104083004.2212520-1-linux@rasmusvillemoes.dk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bpf: Add explicit cast to 'void *' for __BPF_DISPATCHER_UPDATE()
When building with clang:
kernel/bpf/dispatcher.c:126:33: error: pointer type mismatch ('void *' and 'unsigned int (*)(const void *, const struct bpf_insn *, bpf_func_t)' (aka 'unsigned int (*)(const void *, const struct bpf_insn *, unsigned int (*)(const void *, const struct bpf_insn *))')) [-Werror,-Wpointer-type-mismatch]
__BPF_DISPATCHER_UPDATE(d, new ?: &bpf_dispatcher_nop_func);
~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/bpf.h:1045:54: note: expanded from macro '__BPF_DISPATCHER_UPDATE'
__static_call_update((_d)->sc_key, (_d)->sc_tramp, (_new))
^~~~
1 error generated.
The warning is pointing out that the type of new ('void *') and
&bpf_dispatcher_nop_func are not compatible, which could have side
effects coming out of a conditional operator due to promotion rules.
Add the explicit cast to 'void *' to make it clear that this is
expected, as __BPF_DISPATCHER_UPDATE() expands to a call to
__static_call_update(), which expects a 'void *' as its final argument.
Fixes: 68fcb7a7b1e3 ("bpf: Convert BPF_DISPATCHER to use static_call() (not ftrace)") Link: https://github.com/ClangBuiltLinux/linux/issues/1755 Reported-by: kernel test robot <lkp@intel.com> Reported-by: "kernelci.org bot" <bot@kernelci.org> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Acked-by: Björn Töpel <bjorn@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/r/20221107170711.42409-1-nathan@kernel.org Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Liam Howlett [Mon, 7 Nov 2022 20:11:42 +0000 (20:11 +0000)]
fs/userfaultfd: Fix maple tree iterator in userfaultfd_unregister()
When iterating the VMAs, the maple state needs to be invalidated if the
tree is modified by a split or merge to ensure the maple tree node
contained in the maple state is still valid. These invalidations were
missed, so add them to the paths which alter the tree.
Reported-by: syzbot+0d2014e4da2ccced5b41@syzkaller.appspotmail.com Fixes: cfc904214ba4 (userfaultfd: use maple tree iterator to iterate VMAs) Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 7 Nov 2022 18:19:04 +0000 (10:19 -0800)]
Merge tag 'platform-drivers-x86-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"The most important fixes here are a set of fixes for the ACPI
backlight detection refactor which landed in 6.1.
These fix regressions reported on some laptop models by making
acpi_video_backlight_use_native() always return true for now, which in
essence undoes some of the changes.
I plan to take another shot at having only 1 /sys/class/backlight
class device per panel with 6.2, with modified detection heuristics to
avoid the (known) regressions.
Highlights:
- ACPI: video: Fix regressions from 6.1 backlight refactor by making
acpi_video_backlight_use_native() always return true for now
- Misc other bugfixes and HW id additions"
* tag 'platform-drivers-x86-v6.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: p2sb: Don't fail if unknown CPU is found
platform/x86/intel/hid: Add some ACPI device IDs
platform/x86/intel/pmt: Sapphire Rapids PMT errata fix
platform/x86: hp_wmi: Fix rfkill causing soft blocked wifi
platform/x86: touchscreen_dmi: Add info for the RCA Cambio W101 v2 2-in-1
platform/x86: ideapad-laptop: Disable touchpad_switch
ACPI: video: Add backlight=native DMI quirk for Dell G15 5515
ACPI: video: Make acpi_video_backlight_use_native() always return true
ACPI: video: Improve Chromebook checks
Vlastimil Babka [Mon, 7 Nov 2022 16:11:27 +0000 (17:11 +0100)]
mm, slab: remove duplicate kernel-doc comment for ksize()
Akira reports:
> "make htmldocs" reports duplicate C declaration of ksize() as follows:
> /linux/Documentation/core-api/mm-api:43: ./mm/slab_common.c:1428: WARNING: Duplicate C declaration, also defined at core-api/mm-api:212.
> Declaration is '.. c:function:: size_t ksize (const void *objp)'.
> This is due to the kernel-doc comment for ksize() declaration added in
> include/linux/slab.h by commit 502b1be531ad ("slab: Introduce
> kmalloc_size_roundup()").
There is an older kernel-doc comment for ksize() definition in
mm/slab_common.c, which is not only duplicated, but also contradicts the
new one - the additional storage discovered by ksize() should not be
used by callers anymore. Delete the old kernel-doc.
If we're doing device replace on a zoned filesystem and discover in
scrub_enumerate_chunks() that we don't have to copy the block group it is
unlocked before it gets skipped.
But as the block group hasn't yet been locked before it leads to a locking
imbalance. To fix this simply remove the unlock.
This was uncovered by fstests' testcase btrfs/163.
Fixes: 2728feec0a9d ("btrfs: remove lock protection for BLOCK_GROUP_FLAG_TO_COPY") Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
btrfs: zoned: initialize device's zone info for seeding
When performing seeding on a zoned filesystem it is necessary to
initialize each zoned device's btrfs_zoned_device_info structure,
otherwise mounting the filesystem will cause a NULL pointer dereference.
This was uncovered by fstests' testcase btrfs/163.
CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
Since commit 82114c937f24 ("btrfs: scrub: use larger block size for data
extent scrub"), btrfs scrub no longer reports errors if the corruption
is not in the first sector of a STRIPE_LEN.
# 13631488 is the logical bytenr of above 8K extent
btrfs-map-logical -l 13631488 -b 4096 $dev
mirror 1 logical 13631488 physical 13631488 device /dev/test/scratch1
# Corrupt the 2nd sector of that extent
xfs_io -f -c "pwrite -S 0x00 13635584 4k" $dev
mount $dev $mnt
btrfs scrub start -B $mnt
scrub done for 54e63f9f-0c30-4c84-a33b-5c56014629b7
Scrub started: Mon Nov 7 07:18:27 2022
Status: finished
Duration: 0:00:00
Total to scrub: 536.00MiB
Rate: 0.00B/s
Error summary: no errors found <<<
[CAUSE]
That offending commit enlarges the data extent scrub size from sector
size to BTRFS_STRIPE_LEN, to avoid extra scrub_block to be allocated.
But unfortunately the data extent scrub is still heavily relying on the
fact that there is only one scrub_sector per scrub_block.
Thus it will only check the first sector, and ignoring the remaining
sectors.
Furthermore the error reporting is not able to handle multiple sectors
either.
[FIX]
For now just revert the offending commit.
The consequence is just extra memory usage during scrub.
We will need a proper change to make the remaining data scrub path to
handle multiple sectors before we enlarging the data scrub size.
Reported-by: Li Zhang <zhanglikernel@gmail.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
projects / kernel.git / log