binman: Test replacing non-section entries in FIT subsections
A previous patch fixes binman to correctly extract FIT subentries. This
makes it easier to test replacing these entries as we can write tests
using an existing helper function that relies on extracting the replaced
entry.
Add tests that replace leaf entries in FIT subsections with data of
various sizes. Replacing the subsections or the whole FIT section does
not work yet due to the section contents being re-built from unreplaced
subentries' data.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Create FIT subentries in the FIT section, not its parent
When reading images from a file, each entry's data is read from its
parent section as specified in the Entry.Create() call that created it.
The FIT entry type has been creating its subentries under its parent
(their grandparent), as creating them under the FIT entry resulted in an
error until FIT was converted into a proper section.
FIT subentries have their offsets relative to the FIT section, and
reading those offsets in the parent section results in wrong data. The
subentries rightfully belong under the FIT entries, so create them
there. Add tests checking that we can extract the correct data for a FIT
entry and its subentries.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Remove '/images/' fragment from FIT subentry paths
Binman FIT entry nodes describe their subentries in an 'images' subnode,
same as how they would be written for the mkimage executable. The entry
type initially manually managed its subentries keyed by their node paths
relative to its base node. It was later converted to a proper section
while still keeping the same keys for subentries.
These subentry keys of sections are used as path fragments, so they must
not contain the path separator character '/'. Otherwise, they won't be
addressable by binman extract/replace commands. Change these keys from
the '/images/foo' forms to the subentry node names. Extend the simple
FIT tests to check for this.
binman: Don't reset offset/size if image doesn't allow repacking
When an image has the 'allow-repack' property, binman includes the
original offset and size properties from the image description in the
fdtmap. These are later used as the packing constraints when replacing
entries in an image, so other unconstrained entries can be freely
positioned.
Replacing an entry in an image without 'allow-repack' (and therefore the
original offsets) follows the same logic and results in entries being
merely concatenated. Instead, skip resetting the calculated offsets and
sizes to the missing originals for these images so that every entry is
constrained to its existing offset/size.
Add tests that replace an entry with smaller or equal-sized data, in an
image that doesn't allow repacking. Attempting to do so with bigger-size
data is already an error that is already being tested.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Collect bintools for images when replacing entries
Binman entries can use other executables to compute their data, usually
in their ObtainContents() methods. Subclasses of Entry_section would use
bintools in their BuildSectionData() method instead, which is called
from several places including their Pack().
These binary tools are resolved correctly while building an image from a
device-tree description so that they can be used from these methods.
However, this is not being done when replacing entries in an image,
which can result in an error as the Pack() methods attempt to use them.
Collect and resolve entries' bintools also when replacing entries to fix
Pack() errors. Add a way to mock bintool usage in the testing entry type
and tests that check bintools are being resolved for such an entry.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
binman: Fix unique names having '/.' for images read from files
Binman can embed a copy of the image description into the images it
builds as a fdtmap entry, but it omits the /binman/<image-name> prefix
from the node paths while doing so. When reading an already-built image
file, entries are reconstructed using this fdtmap and their associated
nodes still lack that prefix.
Some entries like fit and vblock create intermediate files whose names
are based on an entry unique name. This name is constructed from their
node's path by concatenating the parents with dots up to the binman
node, e.g. /binman/image/foo/bar becomes 'image.foo.bar'.
However, we don't have this /binman/image prefix when replacing entries
in such an image. The /foo/bar entry we read when doing so erroneously
has the unique name of '/.foo.bar', causing permission errors when the
entry attempts to create files based on that.
Fix the unique-name generation by stopping at the '/' node like how it
stops at the binman node. As the unique names are used as filenames, add
tests that check if they're safe to use as filenames.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 23 Apr 2022 12:06:28 +0000 (08:06 -0400)]
Merge branch '2022-04-22-assorted-updates'
- Add "-q" to fdt addr and use it in distro_bootcmd to make the user
experience less scary reading in normal try/fail cases.
- Let the adc update an environment variable like many other commands do
- Fix TPL SEPARATE_BSS check when locating DTB
- Allow ":" in PXE file names again
- Two Apple M1 fixes
Mark Kettenis [Tue, 19 Apr 2022 19:20:31 +0000 (21:20 +0200)]
arm: apple: Point stdout-path to framebuffer when keyboard present
Unless you have a spare Apple Silicon machine, getting access to
the serial port on Apple Silicon machines requires special
hardware. Given that most machines come with a built-in screen
the framebuffer is likely to be the most convenient output device
for most users. While U-Boot will output to both serial and
framebuffer, OSes might not. Therefore set stdout-path to point
at /chosen/framebuffer when a keyboard is connected to the machine.
This behaviour can be overridden by setting the "stdout" variable
in the U-Boot environment. I addition to that keep the serial
console as the default when running under the m1n1 hypervisor.
The m1n1 hypervisor virtualizes the serial port such that it
can be easily accessed from any other machine with a USB port.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Janne Grunau <j@jannau.net> Tested-by: Janne Grunau <j@jannau.net>
Mark Kettenis [Tue, 19 Apr 2022 19:10:29 +0000 (21:10 +0200)]
arm: apple: Don't clear framebuffer
Enable CONFIG_NO_FB_CLEAR to preserve the Asahi logo. Since that
logo is drawn on a black background also enable
CONFIG_SYS_WHITE_ON_BLACK such that text printed by U-Boot is still
visible.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Lyle Franklin [Sat, 16 Apr 2022 15:36:43 +0000 (11:36 -0400)]
Allow colon in PXE bootfile URLs
- U-boot's PXE flow supports prefixing your bootfile name with an
IP address to fetch from a server other than the DHCP server,
e.g. `hostIPaddr:bootfilename`:
https://github.com/u-boot/u-boot/commit/a93907c43f847f076dd0e34ee3b69b5e8e6d0d29
- However, this breaks bootfile paths which contain a colon, e.g.
`f0:ad:4e:10:1b:87/7/pxelinux.cfg/default`
- This patch checks whether the `hostIPaddr` prefix is a valid
IP address before overriding the serverIP otherwise the whole
bootfile path is preserved
Signed-off-by: Lyle Franklin <lylejfranklin@gmail.com>
The documentation for CONFIG_IS_ENABLED() in include/linux/kconfig.h
implies that we will get the correct behaviour, but the actual behaviour
differs such that this condition is now always false.
This stopped TPL being able to load the device tree blob at least on the
ROCKPro64 board (RK3399 SoC), since the wrong device tree location was
chosen.
The issues causing this behaviour with CONFIG_IS_ENABLED() are:
1. The documentation implies that CONFIG_SPL_BUILD =>
CONFIG_SPL_<option> is considered before the TPL equivalent.
Actually, the TPL options have higher priority - see definition of
_CONFIG_PREFIX.
2. The documentation implies a fallthrough, eg. if CONFIG_SPL_BUILD is
defined but the CONFIG_SPL_<option> is not, then it will proceed to
check if CONFIG_TPL_BUILD
Actually, if CONFIG_TPL_BUILD is defined, then it stops there
and CONFIG_SPL_BUILD is not considered - see definition of
_CONFIG_PREFIX.
During TPL build, at least for the ROCKPro64, both CONFIG_TPL_BUILD
and CONFIG_SPL_BUILD are defined, but because of the above, only TPL
options are considered. Since there is no CONFIG_TPL_SEPARATE_BSS,
this fails.
Fixes: 5064a35a96 ("fdt: Correct condition for SEPARATE_BSS") Signed-off-by: Andrew Abbott <andrew@mirx.dev>
Sean Anderson [Wed, 23 Mar 2022 18:26:09 +0000 (14:26 -0400)]
power-domain: Fix use of uninitialized value in dev_power_domain_ctrl
If dev_count_phandle_with_args returns 0 or another error, then pd will never
have been initialized by power_domain_get_by_index. Avoid comparing against
pd.dev in this situation.
Fixes: efbabe6645 ("power-domain: fix hang in endless loop on i.MX8") Signed-off-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Michal Simek [Wed, 9 Mar 2022 09:05:45 +0000 (10:05 +0100)]
usb: dwc3: Add support for usb3-phy PHY configuration
When usb3-phy label is found, PHY driver is called and serdes line is
initialized. This is preparation for serdes/psgtr driver to configure GT
lines based on description in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Jim Liu [Fri, 1 Apr 2022 09:59:39 +0000 (17:59 +0800)]
wdt: nuvoton: Add support for Nuvoton
Add watchdog controller driver for NPCM7xx/npcm8xx
the wdt design of npcm750 and npcm845 is the same.
so the driver can work on npcm750 and npcm845.
about npcm845 wdt dtsi i will followed kernel dts name
to use nuvoton,npcm750-wdt.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 21 Apr 2022 23:55:38 +0000 (19:55 -0400)]
Merge branch '2022-04-21-further-cleanups'
- Fix SPL_SYS_MALLOC_SIMPLE and non-SPL_FRAMEWORK boards (a large number
of PowerPC platforms)
- Remove duplication of crc16 functionality
- Migrate COUNTER_FREQUENCY to CONFIG_COUNTER_FREQUENCY and have it in
Kconfig
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
In arch/arm/mach-imx/imx8m/soc.c there's an implementation of
board_fix_fdt() introduced by commit 3efdcc5fc335. Remove the
redundant one to avoid failed to build from source when enabling
CONFIG_OF_BOARD_FIXUP.
Peng Fan [Wed, 13 Apr 2022 09:47:19 +0000 (17:47 +0800)]
arch: arm: Kconfig: set default COUNTER_FREQUENCY
Set default COUNTER_FREQUENCY according to config header file
under include/configs/
i.MX6UL/ULL/7D/8QM/8QXP all has system counter frequency run at 8MHz,
so set default value for them.
SUNXI/EXYNOS/ROCKCHIP_RK3128/ROCKCHIP_RK3288/ROCKCHIP_RK322X/ROCKCHIP_RK3036
at 24MHz. ARCH_LX2160A at 25MHz
ARCH_ZYNQMP at 100MHz
fs: ext4: Use CRC-16 implementation from linux/crc16.h
Implementation in linux/crc16.h provides standard CRC-16 algorithm with
polynomial x^16 + x^15 + x^2 + 1. Use it and remove duplicate ext4 CRC-16
specific code.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
crc16-ccitt: Rename file with CRC-16-CCITT implementation to crc16-ccitt.c
U-Boot CRC-16 implementation uses polynomial x^16 + x^12 + x^5 + 1 which is
not standard CRC-16 algorithm, but it is known as CRC-16-CCITT. Rename file
crc16.c to crc16-ccitt.c to reduce confusion.
Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Inspection showed that gd->malloc_limit is zero. And it is because
generally SPL_FRAMEWORK initialize SPL's gd->malloc_limit. But when
SPL_FRAMEWORK is not enabled then in most cases nobody initialize
gd->malloc_limit and so SPL malloc simple does not work.
So disable SPL_SYS_MALLOC_SIMPLE by default when SPL_FRAMEWORK is not
enabled. SPL_SYS_MALLOC_SIMPLE can be disabled only by setting
SPL_SYS_MALLOC_F_LEN to zero. So do it.
This change fixes SPL error "alloc space exhausted" on P2020 board.
Tom Rini [Thu, 21 Apr 2022 14:56:58 +0000 (10:56 -0400)]
Merge branch '2022-04-21-assorted-improvements'
- For the environment, add a arch_env_get_location hook and make use of
it on some NXP platforms (so that boards can override SoCs).
- Remove some unused squashfs code from SPL
- Resync am335x beaglebone related DTS files
- Enable SPL_SEPARATE_BSS if SPL_BSS_START_ADDR is used
Enable DM_SERIAL for both U_Boot and the SPL. The uart4 and its pinmux
are already marked with u-boot,dm-spl but we need to move the call to
preloader_console_init() after spl_init() to avoid a board hang
as dm can't be used until after spl_init().
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Cc: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Fabio Estevam <festevam@denx.de> Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Sean Anderson [Tue, 12 Apr 2022 14:59:04 +0000 (10:59 -0400)]
treewide: Enable SPL_SEPARATE_BSS if SPL_BSS_START_ADDR is used
If .bss does not immediately follow the end of the image, then
CONFIG_SPL_SEPARATE_BSS must be selected. Typically, the location of bss
is specified by using CONFIG_SPL_BSS_START_ADDR in a linker script. On
these arches, CONFIG_SPL_SEPARATE_BSS should be enabled. If there is an
option to use an alternate boot script (e.g. CONFIG_SPL_LDSCRIPT is just
a default), just imply. If there is not, select.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Paul Barker [Mon, 11 Apr 2022 15:42:01 +0000 (15:42 +0000)]
board: ti: am335x: Add support for BBE Extended WiFi
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Paul Barker [Mon, 11 Apr 2022 15:42:00 +0000 (15:42 +0000)]
board: ti: am335x: Add BBE Lite support
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Paul Barker [Mon, 11 Apr 2022 15:41:59 +0000 (15:41 +0000)]
arm: dts: Resync dts for BeagleBone and derivatives
Sync BeagleBone dts files & TPS dtsi files with Linux v5.17 and include
the SanCloud BBE Extended WiFi dts added in v5.18-rc1. Also pull in
changes to am33xx-l4.dtsi needed to support the BeagleBone Blue.
The change to use the cpsw switch driver (commit c477358e66a3 in Linux)
is excluded from the sync as u-boot does not recognise the new
compatible string.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Marek Vasut [Wed, 6 Apr 2022 00:21:34 +0000 (02:21 +0200)]
ARM: imx: imx8m: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Marek Vasut [Wed, 6 Apr 2022 00:21:33 +0000 (02:21 +0200)]
armv8: layerscape: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Currently there is only one way to override desired environment location,
by implementing env_get_location(). This is increasingly being conflated
both on board level and architecture level, which leads to a problem on
boards where this function is already implemented on architecture level,
since those boards have no way to override this environment location on
board level anymore.
Implement arch_env_get_location() function which is architecture specific
and should only ever be implemented in architecture code. This function
has lower priority than env_get_location(), which should only ever be
implemented in board code, and which overrides the arch_env_get_location()
architecture environment selection.
This way, architecture can define its default environment chooser, while
board can now override it as needed at all times.
There is no functional change, since env_get_location() simply returns
arch_env_get_location(), and arch_env_get_location() implements the
current env_get_location() default content.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Adam Ford <aford173@gmail.com> Cc: Fabio Estevam <festevam@denx.de> Cc: Marek Behún <marek.behun@nic.cz> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Stefano Babic <sbabic@denx.de> Cc: Tim Harvey <tharvey@gateworks.com> Cc: Tom Rini <trini@konsulko.com> Cc: Tommaso Merciai <tomm.merciai@gmail.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Marek Vasut [Thu, 14 Apr 2022 13:51:46 +0000 (15:51 +0200)]
ARM: imx: imx8m: Fix board_get_usable_ram_top()
The 4 GiB boundary is at 0xffffffff+1 , not at 0x80000000, fix this.
The PHYS_SDRAM of i.MX8M is at 0x40000000 , so to restrict ram_top
below 4 GiB, the ram_top has to be set to 0xffffffff as it is not
an offset from the start of PHYS_SDRAM, but rather a physical address
marking the topmost allowed DRAM address.
Fixes: 3dedf85a11b ("imx8m: Restrict usable memory to space below 4G boundary") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@denx.de> Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tim Harvey [Wed, 13 Apr 2022 22:57:37 +0000 (15:57 -0700)]
pci: imx: remove weak overrides no longer used
There are no users of the imx6_pcie_toggle_power and imx6_pcie_toggle_reset
weak overrides and as these functions are able to be handled now via dt
properties lets remove these.
Cc: Marek Vasut <marex@denx.de> Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tim Harvey [Wed, 13 Apr 2022 22:54:37 +0000 (15:54 -0700)]
pci: imx: use vpcie-supply if defined by device-tree
If vpcie-supply is defined by device-tree use that if
CONFIG_PCIE_IMX_POWER_GPIO is not defined.
Note that after this the following boards which define
CONFIG_PCIE_IMX_POWER_GPIO in their board header file as well as their
device-tree should be able to remove CONFIG_PCIE_IMX_PERST_GPIO without
consequence:
- mx6sabresd
- mx6sxsabresd
- novena
Note that the ge_bx50v3 board uses CONFIG_PCIE_IMX_POWER_GPIO and does
not have vpcie-supply defined in it's pcie node in the dt thus removing
CONFIG_PCIE_IMX_POWER_GPIO globally can't be done until that board adds
vpcie-supply.
Cc: Ian Ray <ian.ray@ge.com> (maintainer:GE BX50V3 BOARD) Cc: Sebastian Reichel <sebastian.reichel@collabora.com> (maintainer:GE BX50V3 BOARD) Cc: Fabio Estevam <festevam@gmail.com> (maintainer:MX6SABRESD BOARD) Cc: Marek Vasut <marex@denx.de> (maintainer:NOVENA BOARD) Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tony Dinh [Sun, 17 Apr 2022 23:42:32 +0000 (16:42 -0700)]
arm: kirkwood: Sheevaplug : Use Marvell uclass mvgbe and PHY driver for Ethernet
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Tim Harvey [Wed, 13 Apr 2022 18:31:09 +0000 (11:31 -0700)]
board: gateworks: venice: add imx8mp-venice-gw740x support
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Tim Harvey [Wed, 13 Apr 2022 18:31:08 +0000 (11:31 -0700)]
board: gateworks: venice: add additional levels for dtb name match
Gateworks produces many products from a single PCB with subloaded
components. Add an additional two levels of dtb name matching so that
for example a GW7400-A matches the dtb name of gw74xx.dtb
Tim Harvey [Wed, 13 Apr 2022 16:29:16 +0000 (09:29 -0700)]
board: gateworks: gw_ventana: use comomn GSC driver
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Tim Harvey [Wed, 13 Apr 2022 16:09:49 +0000 (09:09 -0700)]
imx8m{m,n}-venice-gw7902: add support for GPY111 phy
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy
due to part availability. Add support for it:
- increase post-reset time to 300ms per datasheet
- add tx-delay/rx-delay config
Tim Harvey [Wed, 13 Apr 2022 16:02:44 +0000 (09:02 -0700)]
arm: dts: imx8m*-venice: add gpio hog support
Add gpio hog support for board-specific gpio lines:
- put hogs in u-boot.dtsi so as to keep the regular dts files
in sync with the kernel. The hogs will not be put in the kernel
as that makes them un-usable by userspace as well as
re-initializes them to dt defaults overriding changes which may
have been done by bootloader commands.
- specify gpio names and initial config
- enable GPIO_HOG
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Peng Fan <peng.fan@nxp.com>
Tim Harvey [Wed, 13 Apr 2022 15:56:40 +0000 (08:56 -0700)]
board: gateworks: venice: use common GSC driver
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
configs: tdx: Do not overwrite fdtfile if it got set manually
In case a customer wants to set fdtfile currently preboot overrides it
always with preboot just before the bootdelay. Use test -n to check
if fdtfile is already set and only set it if nothing got touched manually
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
projects / uboot.git / log