The tasklet software interrupt takes too much time. Therefore, the
xfrm_trans_reinject executor is changed from tasklet to workqueue. Add add
spin lock to protect the queue. This reduces the processing flow of the
tcp_sendmsg function in this scenario.
Fixes: e3690f7cbda02 ("xfrm: Reinject transport-mode packets through tasklet") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm: Update ipcomp_scratches with NULL when freed
Currently if ipcomp_alloc_scratches() fails to allocate memory
ipcomp_scratches holds obsolete address. So when we try to free the
percpu scratches using ipcomp_free_scratches() it tries to vfree non
existent vm area. Described below:
static void * __percpu *ipcomp_alloc_scratches(void)
{
...
scratches = alloc_percpu(void *);
if (!scratches)
return NULL;
ipcomp_scratches does not know about this allocation failure.
Therefore holding the old obsolete address.
...
}
Sabrina Dubroca [Thu, 25 Aug 2022 15:16:51 +0000 (17:16 +0200)]
esp: choose the correct inner protocol for GSO on inter address family tunnels
Commit 7d7964597bc3 ("net: Fix esp GSO on inter address family
tunnels.") is incomplete. It passes to skb_eth_gso_segment the
protocol for the outer IP version, instead of the inner IP version, so
we end up calling inet_gso_segment on an inner IPv6 packet and
ipv6_gso_segment on an inner IPv4 packet and the packets are dropped.
This patch completes the fix by selecting the correct protocol based
on the inner mode's family.
Fixes: 95dbc6fbd031 ("xfrm: Add mode handlers for IPsec on layer 2") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Tianyu Yuan [Thu, 25 Aug 2022 08:08:45 +0000 (10:08 +0200)]
nfp: flower: fix ingress police using matchall filter
Referenced commit introduced nfp_policer_validate in the progress
installing rate limiter. This validate check the action id and will
reject police with CONTINUE, which is required to support ingress
police offload.
Fix this issue by allowing FLOW_ACTION_CONTINUE as notexceed action
id in nfp_policer_validate
Fixes: d7826daaf80f ("flow_offload: reject offload for all drivers with invalid police parameters") Signed-off-by: Tianyu Yuan <tianyu.yuan@corigine.com> Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com> Reviewed-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20220825080845.507534-1-simon.horman@corigine.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
openvswitch: fix memory leak at failed datapath creation
ovs_dp_cmd_new()->ovs_dp_change()->ovs_dp_set_upcall_portids()
allocates array via kmalloc.
If for some reason new_vport() fails during ovs_dp_cmd_new()
dp->upcall_portids must be freed.
Add missing kfree.
Florian Fainelli [Thu, 25 Aug 2022 02:39:51 +0000 (19:39 -0700)]
net: smsc911x: Stop and start PHY during suspend and resume
Commit 4faafe4a276b ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state") unveiled that the smsc911x driver was not
properly stopping and restarting the PHY during suspend/resume. Correct
that by indicating that the MAC is in charge of PHY PM operations and
ensure that all MDIO bus activity is quiescent during suspend.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 1b003f68755c ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM") Fixes: cbad73ff1934 ("net: smsc911x: Quieten netif during suspend") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220825023951.3220-1-f.fainelli@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MSI is probably raised by incoming packets, so power down the device
and disable bus mastering to stop the traffic, as user confirmed this
approach works.
In addition to that, be extra safe and cancel reset task if it's running.
Casper Andersson [Thu, 25 Aug 2022 08:49:55 +0000 (10:49 +0200)]
net: sparx5: fix handling uneven length packets in manual extraction
Packets that are not of length divisible by 4 (e.g. 77, 78, 79) would
have the checksum included up to next multiple of 4 (a 77 bytes packet
would have 3 bytes of ethernet checksum included). The check for the
value expects it in host (Little) endian.
Here are a couple of fixes for the current cycle,
see the tag description below.
Just a couple of fixes:
* two potential leaks
* use-after-free in certain scan races
* warning in IBSS code
* error return from a debugfs file was wrong
* possible NULL-ptr-deref when station lookup fails
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhengping Jiang [Tue, 23 Aug 2022 17:28:08 +0000 (10:28 -0700)]
Bluetooth: hci_sync: hold hdev->lock when cleanup hci_conn
When disconnecting all devices, hci_conn_failed is used to cleanup
hci_conn object when the hci_conn object cannot be aborted.
The function hci_conn_failed requires the caller holds hdev->lock.
Fixes: 6a134df1a806d ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted") Signed-off-by: Zhengping Jiang <jiangzp@google.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Wolfram Sang [Thu, 18 Aug 2022 21:02:07 +0000 (23:02 +0200)]
Bluetooth: move from strlcpy with unused retval to strscpy
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Archie Pusaka [Tue, 23 Aug 2022 04:39:22 +0000 (12:39 +0800)]
Bluetooth: hci_event: Fix checking conn for le_conn_complete_evt
To prevent multiple conn complete events, we shouldn't look up the
conn with hci_lookup_le_connect, since it requires the state to be
BT_CONNECT. By the time the duplicate event is processed, the state
might have changed, so we end up processing the new event anyway.
Change the lookup function to hci_conn_hash_lookup_ba.
Bluetooth: ISO: Fix not handling shutdown condition
In order to properly handle shutdown syscall the code shall not assume
that the how argument is always SHUT_RDWR resulting in SHUTDOWN_MASK as
that would result in poll to immediately report EPOLLHUP instead of
properly waiting for disconnect_cfm (Disconnect Complete) which is
rather important for the likes of BAP as the CIG may need to be
reprogrammed.
Fixes: e8b1014d0e46 ("Bluetooth: Add BTPROTO_ISO socket type") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hans de Goede [Sun, 7 Aug 2022 20:57:40 +0000 (22:57 +0200)]
Bluetooth: hci_event: Fix vendor (unknown) opcode status handling
Commit e1e96afe8b21 ("Bluetooth: hci_event: Use of a function table to
handle Command Complete") was (presumably) meant to only refactor things
without any functional changes.
But it does have one undesirable side-effect, before *status would always
be set to skb->data[0] and it might be overridden by some of the opcode
specific handling. While now it always set by the opcode specific handlers.
This means that if the opcode is not known *status does not get set any
more at all!
This behavior change has broken bluetooth support for BCM4343A0 HCIs,
the hci_bcm.c code tries to configure UART attached HCIs at a higher
baudraute using vendor specific opcodes. The BCM4343A0 does not
support this and this used to simply fail:
[ 25.646442] Bluetooth: hci0: BCM: failed to write clock (-56)
[ 25.646481] Bluetooth: hci0: Failed to set baudrate
After which things would continue with the initial baudraute. But now
that hci_cmd_complete_evt() no longer sets status for unknown opcodes
*status is left at 0. This causes the hci_bcm.c code to think the baudraute
has been changed on the HCI side and to also adjust the UART baudrate,
after which communication with the HCI is broken, leading to:
And non working bluetooth. Fix this by restoring the previous
default "*status = skb->data[0]" handling for unknown opcodes.
Fixes: e1e96afe8b21 ("Bluetooth: hci_event: Use of a function table to handle Command Complete") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The problem here is that a range of tnum_range(0, map->max_entries - 1) has
limited ability to represent the concrete tight range with the tnum as the
set of resulting states from value + mask can result in a superset of the
actual intended range, and as such a tnum_in(range, reg->var_off) check may
yield true when it shouldn't, for example tnum_range(0, 2) would result in
00XX -> v = 0000, m = 0011 such that the intended set of {0, 1, 2} is here
represented by a less precise superset of {0, 1, 2, 3}. As the register is
known const scalar, really just use the concrete reg->var_off.value for the
upper index check.
Linus Torvalds [Thu, 25 Aug 2022 21:03:58 +0000 (14:03 -0700)]
Merge tag 'net-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from ipsec and netfilter (with one broken Fixes tag).
Current release - new code bugs:
- dsa: don't dereference NULL extack in dsa_slave_changeupper()
- dpaa: fix <1G ethernet on LS1046ARDB
- neigh: don't call kfree_skb() under spin_lock_irqsave()
Previous releases - regressions:
- r8152: fix the RX FIFO settings when suspending
- dsa: microchip: keep compatibility with device tree blobs with no
phy-mode
- Revert "net: macsec: update SCI upon MAC address change."
- Revert "xfrm: update SA curlft.use_time", comply with RFC 2367
Previous releases - always broken:
- netfilter: conntrack: work around exceeded TCP receive window
- ipsec: fix a null pointer dereference of dst->dev on a metadata dst
in xfrm_lookup_with_ifid
- moxa: get rid of asymmetry in DMA mapping/unmapping
- dsa: microchip: make learning configurable and keep it off while
standalone
- ice: xsk: prohibit usage of non-balanced queue id
- rxrpc: fix locking in rxrpc's sendmsg
Misc:
- another chunk of sysctl data race silencing"
* tag 'net-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
net: lantiq_xrx200: restore buffer if memory allocation failed
net: lantiq_xrx200: fix lock under memory pressure
net: lantiq_xrx200: confirm skb is allocated before using
net: stmmac: work around sporadic tx issue on link-up
ionic: VF initial random MAC address if no assigned mac
ionic: fix up issues with handling EAGAIN on FW cmds
ionic: clear broken state on generation change
rxrpc: Fix locking in rxrpc's sendmsg
net: ethernet: mtk_eth_soc: fix hw hash reporting for MTK_NETSYS_V2
MAINTAINERS: rectify file entry in BONDING DRIVER
i40e: Fix incorrect address type for IPv6 flow rules
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
net: Fix a data-race around sysctl_somaxconn.
net: Fix a data-race around netdev_unregister_timeout_secs.
net: Fix a data-race around gro_normal_batch.
net: Fix data-races around sysctl_devconf_inherit_init_net.
net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
net: Fix a data-race around netdev_budget_usecs.
net: Fix data-races around sysctl_max_skb_frags.
net: Fix a data-race around netdev_budget.
...
====================
net: lantiq_xrx200: fix errors under memory pressure
This series fixes issues that can occur in the driver under memory pressure.
Situations when the system cannot allocate memory are rare, so the mentioned
bugs have been fixed recently. The patches have been tested on a BT Home
router with the Lantiq xRX200 chipset.
Changelog:
v3: - removed netdev_err() log from the first patch
v2:
- the second patch has been changed, so that under memory pressure situation
the driver will not receive packets indefinitely regardless of the NAPI budget,
- the third patch has been added.
====================
net: lantiq_xrx200: restore buffer if memory allocation failed
In a situation where memory allocation fails, an invalid buffer address
is stored. When this descriptor is used again, the system panics in the
build_skb() function when accessing memory.
Fixes: aaabf04caa78 ("lantiq: net: fix duplicated skb in rx descriptor ring") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: lantiq_xrx200: fix lock under memory pressure
When the xrx200_hw_receive() function returns -ENOMEM, the NAPI poll
function immediately returns an error.
This is incorrect for two reasons:
* the function terminates without enabling interrupts or scheduling NAPI,
* the error code (-ENOMEM) is returned instead of the number of received
packets.
After the first memory allocation failure occurs, packet reception is
locked due to disabled interrupts from DMA..
Fixes: 462a72fd466e ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver") Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: lantiq_xrx200: confirm skb is allocated before using
xrx200_hw_receive() assumes build_skb() always works and goes straight
to skb_reserve(). However, build_skb() can fail under memory pressure.
Add a check in case build_skb() failed to allocate and return NULL.
Fixes: 0edcf29e78ce ("net: lantiq_xrx200: convert to build_skb") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Wed, 24 Aug 2022 20:34:49 +0000 (22:34 +0200)]
net: stmmac: work around sporadic tx issue on link-up
This is a follow-up to the discussion in [0]. It seems to me that
at least the IP version used on Amlogic SoC's sometimes has a problem
if register MAC_CTRL_REG is written whilst the chip is still processing
a previous write. But that's just a guess.
Adding a delay between two writes to this register helps, but we can
also simply omit the offending second write. This patch uses the second
approach and is based on a suggestion from Qi Duan.
Benefit of this approach is that we can save few register writes, also
on not affected chip versions.
Jakub Kicinski [Thu, 25 Aug 2022 19:40:29 +0000 (12:40 -0700)]
Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-24 (ixgbe, i40e)
This series contains updates to ixgbe and i40e drivers.
Jake stops incorrect resetting of SYSTIME registers when starting
cyclecounter for ixgbe.
Sylwester corrects a check on source IP address when validating destination
for i40e.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix incorrect address type for IPv6 flow rules
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
====================
Jakub Kicinski [Thu, 25 Aug 2022 19:40:17 +0000 (12:40 -0700)]
Merge branch 'ionic-bug-fixes'
Shannon Nelson says:
====================
ionic: bug fixes
These are a couple of maintenance bug fixes for the Pensando ionic
networking driver.
Mohamed takes care of a "plays well with others" issue where the
VF spec is a bit vague on VF mac addresses, but certain customers
have come to expect behavior based on other vendor drivers.
Shannon addresses a couple of corner cases seen in internal
stress testing.
====================
R Mohamed Shah [Wed, 24 Aug 2022 16:50:51 +0000 (09:50 -0700)]
ionic: VF initial random MAC address if no assigned mac
Assign a random mac address to the VF interface station
address if it boots with a zero mac address in order to match
similar behavior seen in other VF drivers. Handle the errors
where the older firmware does not allow the VF to set its own
station address.
Newer firmware will allow the VF to set the station mac address
if it hasn't already been set administratively through the PF.
Setting it will also be allowed if the VF has trust.
Fixes: 891d6f039073 ("ionic: support sr-iov operations") Signed-off-by: R Mohamed Shah <mohamed@pensando.io> Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Shannon Nelson [Wed, 24 Aug 2022 16:50:50 +0000 (09:50 -0700)]
ionic: fix up issues with handling EAGAIN on FW cmds
In looping on FW update tests we occasionally see the
FW_ACTIVATE_STATUS command fail while it is in its EAGAIN loop
waiting for the FW activate step to finsh inside the FW. The
firmware is complaining that the done bit is set when a new
dev_cmd is going to be processed.
Doing a clean on the cmd registers and doorbell before exiting
the wait-for-done and cleaning the done bit before the sleep
prevents this from occurring.
Fixes: 22c2f0b535b9 ("ionic: Add hardware init and device commands") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Shannon Nelson [Wed, 24 Aug 2022 16:50:49 +0000 (09:50 -0700)]
ionic: clear broken state on generation change
There is a case found in heavy testing where a link flap happens just
before a firmware Recovery event and the driver gets stuck in the
BROKEN state. This comes from the driver getting interrupted by a FW
generation change when coming back up from the link flap, and the call
to ionic_start_queues() in ionic_link_status_check() fails. This can be
addressed by having the fw_up code clear the BROKEN bit if seen, rather
than waiting for a user to manually force the interface down and then
back up.
Fixes: 1600eba726cb ("ionic: stop watchdog when in broken state") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David Howells [Wed, 24 Aug 2022 16:35:45 +0000 (17:35 +0100)]
rxrpc: Fix locking in rxrpc's sendmsg
Fix three bugs in the rxrpc's sendmsg implementation:
(1) rxrpc_new_client_call() should release the socket lock when returning
an error from rxrpc_get_call_slot().
(2) rxrpc_wait_for_tx_window_intr() will return without the call mutex
held in the event that we're interrupted by a signal whilst waiting
for tx space on the socket or relocking the call mutex afterwards.
Fix this by: (a) moving the unlock/lock of the call mutex up to
rxrpc_send_data() such that the lock is not held around all of
rxrpc_wait_for_tx_window*() and (b) indicating to higher callers
whether we're return with the lock dropped. Note that this means
recvmsg() will not block on this call whilst we're waiting.
(3) After dropping and regaining the call mutex, rxrpc_send_data() needs
to go and recheck the state of the tx_pending buffer and the
tx_total_len check in case we raced with another sendmsg() on the same
call.
Thinking on this some more, it might make sense to have different locks for
sendmsg() and recvmsg(). There's probably no need to make recvmsg() wait
for sendmsg(). It does mean that recvmsg() can return MSG_EOR indicating
that a call is dead before a sendmsg() to that call returns - but that can
currently happen anyway.
Without fix (2), something like the following can be induced:
WARNING: bad unlock balance detected!
5.16.0-rc6-syzkaller #0 Not tainted
-------------------------------------
syz-executor011/3597 is trying to release lock (&call->user_mutex) at:
[<ffffffff885163a3>] rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748
but there are no more locks to release!
other info that might help us debug this:
no locks held by syz-executor011/3597.
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_unlock_imbalance_bug include/trace/events/lock.h:58 [inline]
__lock_release kernel/locking/lockdep.c:5306 [inline]
lock_release.cold+0x49/0x4e kernel/locking/lockdep.c:5657
__mutex_unlock_slowpath+0x99/0x5e0 kernel/locking/mutex.c:900
rxrpc_do_sendmsg+0xc13/0x1350 net/rxrpc/sendmsg.c:748
rxrpc_sendmsg+0x420/0x630 net/rxrpc/af_rxrpc.c:561
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:724
____sys_sendmsg+0x6e8/0x810 net/socket.c:2409
___sys_sendmsg+0xf3/0x170 net/socket.c:2463
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2492
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
[Thanks to Hawkins Jiawei and Khalid Masum for their attempts to fix this]
Fixes: 8d0c6fe295af ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Reported-by: syzbot+7f0483225d0c94cb3441@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: syzbot+7f0483225d0c94cb3441@syzkaller.appspotmail.com
cc: Hawkins Jiawei <yin31149@gmail.com>
cc: Khalid Masum <khalid.masum.92@gmail.com>
cc: Dan Carpenter <dan.carpenter@oracle.com>
cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/166135894583.600315.7170979436768124075.stgit@warthog.procyon.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge branch 'Fix incorrect pruning for ARG_CONST_ALLOC_SIZE_OR_ZERO'
Kumar Kartikeya Dwivedi says:
====================
A fix for a missing mark_chain_precision call that leads to eager pruning and
loading of invalid programs when the more permissive case is in the straight
line exploration. Please see the commit log for details, and selftest for an
example.
====================
selftests/bpf: Add regression test for pruning fix
Add a test to ensure we do mark_chain_precision for the argument type
ARG_CONST_ALLOC_SIZE_OR_ZERO. For other argument types, this was already
done, but propagation for missing for this case. Without the fix, this
test case loads successfully.
bpf: Do mark_chain_precision for ARG_CONST_ALLOC_SIZE_OR_ZERO
Precision markers need to be propagated whenever we have an ARG_CONST_*
style argument, as the verifier cannot consider imprecise scalars to be
equivalent for the purposes of states_equal check when such arguments
refine the return value (in this case, set mem_size for PTR_TO_MEM). The
resultant mem_size for the R0 is derived from the constant value, and if
the verifier incorrectly prunes states considering them equivalent where
such arguments exist (by seeing that both registers have reg->precise as
false in regsafe), we can end up with invalid programs passing the
verifier which can do access beyond what should have been the correct
mem_size in that explored state.
For the first case, the single line execution's exploration will prune
the search at insn 14 for the branch insn 9's second leg as it will be
verified first using r2 = -1 (UINT_MAX), while as w1 at insn 9 will
always be 0 so at runtime we don't get error for being greater than
UINT_MAX/4 from bpf_ringbuf_reserve. The verifier during regsafe just
sees reg->precise as false for both r2 registers in both states, hence
considers them equal for purposes of states_equal.
If we propagated precise markers using the backtracking support, we
would use the precise marking to then ensure that old r2 (UINT_MAX) was
within the new r2 (1) and this would never be true, so the verification
would rightfully fail.
The end result is that the out of bounds access at instruction 19 would
be permitted without this fix.
Note that reg->precise is always set to true when user does not have
CAP_BPF (or when subprog count is greater than 1 (i.e. use of any static
or global functions)), hence this is only a problem when precision marks
need to be explicitly propagated (i.e. privileged users with CAP_BPF).
A simplified test case has been included in the next patch to prevent
future regressions.
Fixes: 8d560509c598 ("bpf: Implement BPF ring buffer and verifier support for it") Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com> Link: https://lore.kernel.org/r/20220823185300.406-2-memxor@gmail.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Linus Torvalds [Thu, 25 Aug 2022 17:52:16 +0000 (10:52 -0700)]
Merge tag 'cgroup-for-6.0-rc2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull another cgroup fix from Tejun Heo:
"Commit baf59de3daeb ("cgroup: Fix threadgroup_rwsem <->
cpus_read_lock() deadlock") required the cgroup
core to grab cpus_read_lock() before invoking ->attach().
Unfortunately, it missed adding cpus_read_lock() in
cgroup_attach_task_all(). Fix it"
* tag 'cgroup-for-6.0-rc2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Add missing cpus_read_lock() to cgroup_attach_task_all()
Tetsuo Handa [Thu, 25 Aug 2022 08:38:38 +0000 (17:38 +0900)]
cgroup: Add missing cpus_read_lock() to cgroup_attach_task_all()
syzbot is hitting percpu_rwsem_assert_held(&cpu_hotplug_lock) warning at
cpuset_attach() [1], for commit baf59de3daebd355 ("cgroup: Fix
threadgroup_rwsem <-> cpus_read_lock() deadlock") missed that
cpuset_attach() is also called from cgroup_attach_task_all().
Add cpus_read_lock() like what cgroup_procs_write_start() does.
Dan Carpenter [Thu, 28 Jul 2022 14:25:16 +0000 (17:25 +0300)]
wifi: mac80211: potential NULL dereference in ieee80211_tx_control_port()
The ieee80211_lookup_ra_sta() function will sometimes set "sta" to NULL
so add this NULL check to prevent an Oops.
Fixes: a51576ec5290 ("wifi: nl80211/mac80211: clarify link ID in control port TX") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/YuKcTAyO94YOy0Bu@kili Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Dan Carpenter [Thu, 4 Aug 2022 07:03:21 +0000 (10:03 +0300)]
wifi: cfg80211: debugfs: fix return type in ht40allow_map_read()
The return type is supposed to be ssize_t, which is signed long,
but "r" was declared as unsigned int. This means that on 64 bit systems
we return positive values instead of negative error codes.
Fixes: 0edb6bf6a000 ("cfg80211: add debugfs HT40 allow map") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/YutvOQeJm0UjLhwU@kili Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wifi: mac80211: Don't finalize CSA in IBSS mode if state is disconnected
When we are not connected to a channel, sending channel "switch"
announcement doesn't make any sense.
The BSS list is empty in that case. This causes the for loop in
cfg80211_get_bss() to be bypassed, so the function returns NULL
(check line 1424 of net/wireless/scan.c), causing the WARN_ON()
in ieee80211_ibss_csa_beacon() to get triggered (check line 500
of net/mac80211/ibss.c), which was consequently reported on the
syzkaller dashboard.
Thus, check if we have an existing connection before generating
the CSA beacon in ieee80211_ibss_finish_csa().
ieee80211_scan_rx() tries to access scan_req->flags after a
null check, but a UAF is observed when the scan is completed
and __ieee80211_scan_completed() executes, which then calls
cfg80211_scan_done() leading to the freeing of scan_req.
Since scan_req is rcu_dereference()'d, prevent the racing in
__ieee80211_scan_completed() by ensuring that from mac80211's
POV it is no longer accessed from an RCU read critical section
before we call cfg80211_scan_done().
1) Fix crash with malformed ebtables blob which do not provide all
entry points, from Florian Westphal.
2) Fix possible TCP connection clogging up with default 5-days
timeout in conntrack, from Florian.
3) Fix crash in nf_tables tproxy with unsupported chains, also from Florian.
4) Do not allow to update implicit chains.
5) Make table handle allocation per-netns to fix data race.
6) Do not truncated payload length and offset, and checksum offset.
Instead report EINVAl.
7) Enable chain stats update via static key iff no error occurs.
8) Restrict osf expression to ip, ip6 and inet families.
9) Restrict tunnel expression to netdev family.
10) Fix crash when trying to bind again an already bound chain.
11) Flowtable garbage collector might leave behind pending work to
delete entries. This patch comes with a previous preparation patch
as dependency.
12) Allow net.netfilter.nf_conntrack_frag6_high_thresh to be lowered,
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_defrag_ipv6: allow nf_conntrack_frag6_high_thresh increases
netfilter: flowtable: fix stuck flows on cleanup due to pending work
netfilter: flowtable: add function to invoke garbage collection immediately
netfilter: nf_tables: disallow binding to already bound chain
netfilter: nft_tunnel: restrict it to netdev family
netfilter: nft_osf: restrict osf to ipv4, ipv6 and inet families
netfilter: nf_tables: do not leave chain stats enabled on error
netfilter: nft_payload: do not truncate csum_offset and csum_type
netfilter: nft_payload: report ERANGE for too long offset and length
netfilter: nf_tables: make table handle allocation per-netns friendly
netfilter: nf_tables: disallow updates of implicit chain
netfilter: nft_tproxy: restrict to prerouting hook
netfilter: conntrack: work around exceeded receive window
netfilter: ebtables: reject blobs that don't provide all entry points
====================
i40e: Fix incorrect address type for IPv6 flow rules
It was not possible to create 1-tuple flow director
rule for IPv6 flow type. It was caused by incorrectly
checking for source IP address when validating user provided
destination IP address.
Fix this by changing ip6src to correct ip6dst address
in destination IP address validation for IPv6 flow type.
Fixes: 06962af1fda1 ("i40e: Add flow director support for IPv6") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Jacob Keller [Tue, 2 Aug 2022 00:24:19 +0000 (17:24 -0700)]
ixgbe: stop resetting SYSTIME in ixgbe_ptp_start_cyclecounter
The ixgbe_ptp_start_cyclecounter is intended to be called whenever the
cyclecounter parameters need to be changed.
Since commit 8b95512ad51a ("ixgbe: Update PTP to support X550EM_x
devices"), this function has cleared the SYSTIME registers and reset the
TSAUXC DISABLE_SYSTIME bit.
While these need to be cleared during ixgbe_ptp_reset, it is wrong to clear
them during ixgbe_ptp_start_cyclecounter. This function may be called
during both reset and link status change. When link changes, the SYSTIME
counter is still operating normally, but the cyclecounter should be updated
to account for the possibly changed parameters.
Clearing SYSTIME when link changes causes the timecounter to jump because
the cycle counter now reads zero.
Extract the SYSTIME initialization out to a new function and call this
during ixgbe_ptp_reset. This prevents the timecounter adjustment and avoids
an unnecessary reset of the current time.
This also restores the original SYSTIME clearing that occurred during
ixgbe_ptp_reset before the commit above.
Reported-by: Steve Payne <spayne@aurora.tech> Reported-by: Ilya Evenbach <ievenbach@aurora.tech> Fixes: 8b95512ad51a ("ixgbe: Update PTP to support X550EM_x devices") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Linus Torvalds [Wed, 24 Aug 2022 17:43:34 +0000 (10:43 -0700)]
Merge tag 'trace-v6.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
- Fix build warning for when MODULES and FTRACE_WITH_DIRECT_CALLS are
not set. A warning happens with ops_references_rec() defined but not
used.
* tag 'trace-v6.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix build warning for ops_references_rec() not used
David S. Miller [Wed, 24 Aug 2022 12:46:59 +0000 (13:46 +0100)]
Merge branch 'sysctl-data-races'
Kuniyuki Iwashima says:
====================
net: sysctl: Fix data-races around net.core.XXX
This series fixes data-races around all knobs in net_core_table and
netns_core_table except for bpf stuff.
These knobs are skipped:
- 4 bpf knobs
- netdev_rss_key: Written only once by net_get_random_once() and
read-only knob
- rps_sock_flow_entries: Protected with sock_flow_mutex
- flow_limit_cpu_bitmap: Protected with flow_limit_update_mutex
- flow_limit_table_len: Protected with flow_limit_update_mutex
- default_qdisc: Protected with qdisc_mod_lock
- warnings: Unused
- high_order_alloc_disable: Protected with static_key_mutex
- skb_defer_max: Already using READ_ONCE()
- sysctl_txrehash: Already using READ_ONCE()
Note 5th patch fixes net.core.message_cost and net.core.message_burst,
and lib/ratelimit.c does not have an explicit maintainer.
Changes:
v3:
* Fix build failures of CONFIG_SYSCTL=n case in 13th & 14th patches
While reading gro_normal_batch, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 02b56483900a ("net: use listified RX for handling GRO_NORMAL skbs") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix data-races around sysctl_devconf_inherit_init_net.
While reading sysctl_devconf_inherit_init_net, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: dcd27ebd94a2 ("net: introduce a knob to control whether to inherit devconf config") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix data-races around sysctl_fb_tunnels_only_for_init_net.
While reading sysctl_fb_tunnels_only_for_init_net, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 1aff42fd5d92 ("net: do not create fallback tunnels for non-default namespaces") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While reading netdev_budget_usecs, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1284c40c9b04 ("Replace 2 jiffies with sysctl netdev_budget_usecs to enable softirq tuning") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_max_skb_frags, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 55a065f92e7a ("net:Add sysctl_max_skb_frags") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While reading netdev_budget, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 983507ab3bc6 ("[NET]: Separate two usages of netdev_max_backlog.") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix a data-race around sysctl_tstamp_allow_data.
While reading sysctl_tstamp_allow_data, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 5b2c0c8cf9ac ("net-timestamp: no-payload only sysctl") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
While reading rs->interval and rs->burst, they can be changed
concurrently via sysctl (e.g. net_ratelimit_state). Thus, we
need to add READ_ONCE() to their readers.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix data-races around netdev_tstamp_prequeue.
While reading netdev_tstamp_prequeue, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 769c199f0e89 ("net: Consistent skb timestamping") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix data-races around weight_p and dev_weight_[rt]x_bias.
While reading weight_p, it can be changed concurrently. Thus, we need
to add READ_ONCE() to its reader.
Also, dev_[rt]x_weight can be read/written at the same time. So, we
need to use READ_ONCE() and WRITE_ONCE() for its access. Moreover, to
use the same weight_p while changing dev_[rt]x_weight, we add a mutex
in proc_do_dev_weight().
Fixes: bf9cdb706271 ("net: dev_weight: TX/RX orthogonality") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Csókás Bence [Mon, 22 Aug 2022 08:10:52 +0000 (10:10 +0200)]
fec: Restart PPS after link state change
On link state change, the controller gets reset,
causing PPS to drop out and the PHC to lose its
time and calibration. So we restart it if needed,
restoring calibration and time registers.
Changes since v2:
* Add `fec_ptp_save_state()`/`fec_ptp_restore_state()`
* Use `ktime_get_real_ns()`
* Use `BIT()` macro
Changes since v1:
* More ECR #define's
* Stop PPS in `fec_ptp_stop()`
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Yingliang [Mon, 22 Aug 2022 02:53:46 +0000 (10:53 +0800)]
net: neigh: don't call kfree_skb() under spin_lock_irqsave()
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So add all skb to
a tmp list, then free them after spin_unlock_irqrestore() at
once.
Fixes: a6b7801f2c1e ("neigh: fix possible DoS due to net iface start/stop loop") Suggested-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, net.netfilter.nf_conntrack_frag6_high_thresh can only be lowered.
I found this issue while investigating a probable kernel issue
causing flakes in tools/testing/selftests/net/ip_defrag.sh
In particular, these sysctl changes were ignored:
ip netns exec "${NETNS}" sysctl -w net.netfilter.nf_conntrack_frag6_high_thresh=9000000 >/dev/null 2>&1
ip netns exec "${NETNS}" sysctl -w net.netfilter.nf_conntrack_frag6_low_thresh=7000000 >/dev/null 2>&1
This change is inline with commit 3a4c1ede99b7 ("net/ipfrag: let ip[6]frag_high_thresh
in ns be higher than in init_net")
Fixes: 8db3d41569bb ("netfilter: nf_defrag_ipv6: use net_generic infra") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: flowtable: fix stuck flows on cleanup due to pending work
To clear the flow table on flow table free, the following sequence
normally happens in order:
1) gc_step work is stopped to disable any further stats/del requests.
2) All flow table entries are set to teardown state.
3) Run gc_step which will queue HW del work for each flow table entry.
4) Waiting for the above del work to finish (flush).
5) Run gc_step again, deleting all entries from the flow table.
6) Flow table is freed.
But if a flow table entry already has pending HW stats or HW add work
step 3 will not queue HW del work (it will be skipped), step 4 will wait
for the pending add/stats to finish, and step 5 will queue HW del work
which might execute after freeing of the flow table.
To fix the above, this patch flushes the pending work, then it sets the
teardown flag to all flows in the flowtable and it forces a garbage
collector run to queue work to remove the flows from hardware, then it
flushes this new pending work and (finally) it forces another garbage
collector run to remove the entry from the software flowtable.
Linus Torvalds [Wed, 24 Aug 2022 02:33:28 +0000 (19:33 -0700)]
Merge tag 'cgroup-for-6.0-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- The psi data structure was changed to be allocated dynamically but
it wasn't being cleared leading to it reporting garbage values and
triggering spurious oom kills.
- A deadlock involving cpuset and cpu hotplug.
- When a controller is moved across cgroup hierarchies,
css->rstat_css_node didn't get RCU drained properly from the previous
list.
* tag 'cgroup-for-6.0-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: Fix race condition at rebind_subsystems()
cgroup: Fix threadgroup_rwsem <-> cpus_read_lock() deadlock
sched/psi: Remove redundant cgroup_psi() when !CONFIG_CGROUPS
sched/psi: Remove unused parameter nbytes of psi_trigger_create()
sched/psi: Zero the memory of struct psi_group
Linus Torvalds [Wed, 24 Aug 2022 02:26:48 +0000 (19:26 -0700)]
Merge tag 'audit-pr-20220823' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"A single fix for a potential double-free on a fsnotify error path"
* tag 'audit-pr-20220823' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix potential double free on error path from fsnotify_add_inode_mark
Linus Torvalds [Wed, 24 Aug 2022 02:17:26 +0000 (19:17 -0700)]
Merge tag 'fs.fixes.v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping
Pull file_remove_privs() fix from Christian Brauner:
"As part of Stefan's and Jens' work to add async buffered write
support to xfs we refactored file_remove_privs() and added
__file_remove_privs() to avoid calling __remove_privs() when
IOCB_NOWAIT is passed.
While debugging a recent performance regression report I found that
during review we missed that commit 7d6646b3c511 ("fs: add
__remove_file_privs() with flags parameter") accidently changed
behavior when dentry_needs_remove_privs() returns zero.
Before the commit it would still call inode_has_no_xattr() setting
the S_NOSEC bit and thereby avoiding even calling into
dentry_needs_remove_privs() the next time this function is called.
After that commit inode_has_no_xattr() would only be called if
__remove_privs() had to be called.
Restore the old behavior. This is likely the cause of the performance
regression"
* tag 'fs.fixes.v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping:
fs: __file_remove_privs(): restore call to inode_has_no_xattr()
Jakub Kicinski [Wed, 24 Aug 2022 00:50:26 +0000 (17:50 -0700)]
Merge tag 'mlx5-fixes-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2022-08-22
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Unlock on error in mlx5_sriov_enable()
net/mlx5e: Fix use after free in mlx5e_fs_init()
net/mlx5e: kTLS, Use _safe() iterator in mlx5e_tls_priv_tx_list_cleanup()
net/mlx5: unlock on error path in esw_vfs_changed_event_handler()
net/mlx5e: Fix wrong tc flag used when set hw-tc-offload off
net/mlx5e: TC, Add missing policer validation
net/mlx5e: Fix wrong application of the LRO state
net/mlx5: Avoid false positive lockdep warning by adding lock_class_key
net/mlx5: Fix cmd error logging for manage pages cmd
net/mlx5: Disable irq when locking lag_lock
net/mlx5: Eswitch, Fix forwarding decision to uplink
net/mlx5: LAG, fix logic over MLX5_LAG_FLAG_NDEVS_READY
net/mlx5e: Properly disable vlan strip on non-UL reps
====================
this small series is supposed to fix the issues around AF_XDP usage with
reduced queue count on interface. Due to the XDP rings setup, some
configurations can result in sockets not seeing traffic flowing. More
about this in description of patch 2.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: xsk: use Rx ring's XDP ring when picking NAPI context
ice: xsk: prohibit usage of non-balanced queue id
====================
Jakub Kicinski [Tue, 23 Aug 2022 22:32:24 +0000 (15:32 -0700)]
Merge branch 'bnxt_en-bug-fixes'
Michael Chan says:
====================
bnxt_en: Bug fixes
This series includes 2 fixes for regressions introduced by the XDP
multi-buffer feature, 1 devlink reload bug fix, and 1 SRIOV resource
accounting bug fix.
====================
Vikas Gupta [Mon, 22 Aug 2022 15:06:54 +0000 (11:06 -0400)]
bnxt_en: fix LRO/GRO_HW features in ndo_fix_features callback
LRO/GRO_HW should be disabled if there is an attached XDP program.
BNXT_FLAG_TPA is the current setting of the LRO/GRO_HW. Using
BNXT_FLAG_TPA to disable LRO/GRO_HW will cause these features to be
permanently disabled once they are disabled.
Fixes: 24310a46690f ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff") Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vikas Gupta [Mon, 22 Aug 2022 15:06:53 +0000 (11:06 -0400)]
bnxt_en: fix NQ resource accounting during vf creation on 57500 chips
There are 2 issues:
1. We should decrement hw_resc->max_nqs instead of hw_resc->max_irqs
with the number of NQs assigned to the VFs. The IRQs are fixed
on each function and cannot be re-assigned. Only the NQs are being
assigned to the VFs.
2. vf_msix is the total number of NQs to be assigned to the VFs. So
we should decrement vf_msix from hw_resc->max_nqs.
Fixes: 10315942f1db ("bnxt_en: Add SR-IOV support for 57500 chips.") Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pavan Chebbi [Mon, 22 Aug 2022 15:06:51 +0000 (11:06 -0400)]
bnxt_en: Use PAGE_SIZE to init buffer when multi buffer XDP is not in use
Using BNXT_PAGE_MODE_BUF_SIZE + offset as buffer length value is not
sufficient when running single buffer XDP programs doing redirect
operations. The stack will complain on missing skb tail room. Fix it
by using PAGE_SIZE when calling xdp_init_buff() for single buffer
programs.
Fixes: afd5faadc9de ("bnxt: refactor bnxt_rx_xdp to separate xdp_init_buff/xdp_prepare_buff") Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reading bpf_jit_limit, it can be changed concurrently via sysctl,
WRITE_ONCE() in __do_proc_doulongvec_minmax(). The size of bpf_jit_limit
is long, so we need to add a paired READ_ONCE() to avoid load-tearing.
Vladimir Oltean [Thu, 18 Aug 2022 16:48:09 +0000 (19:48 +0300)]
net: dsa: microchip: make learning configurable and keep it off while standalone
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Linus Torvalds [Tue, 23 Aug 2022 20:42:31 +0000 (13:42 -0700)]
Merge tag 'parisc-for-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Some interesting background to the current patchset:
It turned out that the fldw instruction (which loads a 32-bit word
from memory into one half of a FP register) failed on unaligned
addresses and even trashed some other random FP register instead. It's
a trivial one-liner fix in the exception handler but this failure
dates back to the very beginnings of the parisc-port. It's strange
that it was never noticed before.
Another patch fixes an annoyance noticed by Randy Dunlap. Running
"make ARCH=parisc64 randconfig" always returned a 32-bit config,
although one would expect a 64-bit config. Masahiro Yamada suggested
to mimik sparc Kconfig code, which fixed the issue nicely. This
allowed to drop some compiler build checks too.
Third, it's possible to build an optimized 32-bit kernel for PA8X00
(64-bit) CPUs, which then wouldn't start on 32-bit-only (PA1.x)
machines. I've added a bootup check which prevents that and which
prints a message to the console. This can be tested with qemu, which
currently only supports 32-bit emulation.
The other patches are usual clean-up stuff like added return value
checks and typo fixes in comments.
Summary:
- Fix emulation of fldw instruction on unaligned addresses
- Fix "make ARCH=parisc64 randconfig" to return a 64-bit config
- Prevent boot if trying to boot a 32-bit kernel compiled for PA8X00
CPUs on 32-bit only machines
- ccio-dma: Handle kmalloc failure in ccio_init_resources()"
* tag 'parisc-for-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Add runtime check to prevent PA2.0 kernels on PA1.x machines
parisc: ccio-dma: Handle kmalloc failure in ccio_init_resources()
parisc: led: Move from strlcpy with unused retval to strscpy
parisc: ccio-dma: Fix typo in comment
Revert "parisc: Show error if wrong 32/64-bit compiler is being used"
parisc: Make CONFIG_64BIT available for ARCH=parisc64 only
parisc: Fix exception handler for fldw and fstw instructions
Linus Torvalds [Tue, 23 Aug 2022 20:33:08 +0000 (13:33 -0700)]
Merge tag 'mm-hotfixes-stable-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"Thirteen fixes, almost all for MM.
Seven of these are cc:stable and the remainder fix up the changes
which went into this -rc cycle"
* tag 'mm-hotfixes-stable-2022-08-22' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
kprobes: don't call disarm_kprobe() for disabled kprobes
mm/shmem: shmem_replace_page() remember NR_SHMEM
mm/shmem: tmpfs fallocate use file_modified()
mm/shmem: fix chattr fsflags support in tmpfs
mm/hugetlb: support write-faults in shared mappings
mm/hugetlb: fix hugetlb not supporting softdirty tracking
mm/uffd: reset write protection when unregister with wp-mode
mm/smaps: don't access young/dirty bit if pte unpresent
mm: add DEVICE_ZONE to FOR_ALL_ZONES
kernel/sys_ni: add compat entry for fadvise64_64
mm/gup: fix FOLL_FORCE COW security issue and remove FOLL_COW
Revert "zram: remove double compression logic"
get_maintainer: add Alan to .get_maintainer.ignore
Linus Torvalds [Tue, 23 Aug 2022 20:23:07 +0000 (13:23 -0700)]
Merge tag 'linux-kselftest-kunit-fixes-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"Fix for a mmc test and to load .kunit_test_suites section when
CONFIG_KUNIT=m, and not just when KUnit is built-in"
* tag 'linux-kselftest-kunit-fixes-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
module: kunit: Load .kunit_test_suites section when CONFIG_KUNIT=m
mmc: sdhci-of-aspeed: test: Fix dependencies when KUNIT=m
Linus Torvalds [Tue, 23 Aug 2022 20:13:36 +0000 (13:13 -0700)]
Merge tag 'linux-kselftest-fixes-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
"Fixes to vm and sgx test builds"
* tag 'linux-kselftest-fixes-6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/vm: fix inability to build any vm tests
selftests/sgx: Ignore OpenSSL 3.0 deprecated functions warning
projects / kernel.git / log