When the PHY and the MAC are capable of doing timestamping, the PHY has
priority. Therefore the DT option lan8814,ignore-ts was added such that
the PHY will not expose a PHC so then the timestamping was done in the
MAC. This is not the correct approach of doing it, therefore remove
this.
Fixes: db523972fb2e1c ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the discussions here[1], the PHY driver is the wrong place
to set the latencies, therefore remove them.
[1] https://lkml.org/lkml/2022/3/4/325
Fixes: db523972fb2e1c ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
dt-bindings: net: micrel: Revert latency support and timestamping check
Revert latency support from binding.
Based on the discussion[1], the DT is the wrong place to have the
lantecies for the PHY.
[1] https://lkml.org/lkml/2022/3/4/325
Fixes: c3075dfed92e82 ("dt-bindings: net: micrel: Configure latency values and timestamping check for LAN8814 phy") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: net: fix nexthop warning cleanup double ip typo
I made a stupid typo when adding the nexthop route warning selftest and
added both $IP and ip after it (double ip) on the cleanup path. The
error doesn't show up when running the test, but obviously it doesn't
cleanup properly after it.
Fixes: ebc172b37e74 ("selftests: net: add delete nexthop route warning test") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Chen-Yu Tsai [Thu, 31 Mar 2022 18:48:32 +0000 (02:48 +0800)]
net: stmmac: Fix unset max_speed difference between DT and non-DT platforms
In commit 3cc3656dfb9c ("net: stmmac: support max-speed device tree
property"), when DT platforms don't set "max-speed", max_speed is set to
-1; for non-DT platforms, it stays the default 0.
Prior to commit 0357a52f9d1c ("net: stmmac: Start adding phylink support"),
the check for a valid max_speed setting was to check if it was greater
than zero. This commit got it right, but subsequent patches just checked
for non-zero, which is incorrect for DT platforms.
In commit b87fd36b3dc4 ("net: stmmac: convert to phylink_get_linkmodes()")
the conversion switched completely to checking for non-zero value as a
valid value, which caused 1000base-T to stop getting advertised by
default.
Instead of trying to fix all the checks, simply leave max_speed alone if
DT property parsing fails.
Fixes: 3cc3656dfb9c ("net: stmmac: support max-speed device tree property") Fixes: b87fd36b3dc4 ("net: stmmac: convert to phylink_get_linkmodes()") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20220331184832.16316-1-wens@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The first patch fixes a warning that can be triggered by deleting a
nexthop route and specifying a device (more info in its commit msg).
And the second patch adds a selftest for that case.
Chose this way to fix it because we should match when deleting without
nh spec and should fail when deleting a nexthop route with old-style nh
spec because nexthop objects are managed separately, e.g.:
$ ip r show 1.2.3.4/32
1.2.3.4 nhid 12 via 192.168.11.2 dev dummy0
$ ip r del 1.2.3.4/32
$ ip r del 1.2.3.4/32 nhid 12
<both should work>
$ ip r del 1.2.3.4/32 dev dummy0
<should fail with ESRCH>
v2: addded more to patch 01's commit message
adjusted the test comment in patch 02
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: net: add delete nexthop route warning test
Add a test which causes a WARNING on kernels which treat a
nexthop route like a normal route when comparing for deletion and a
device is specified. That is, a route is found but we hit a warning while
matching it. The warning is from fib_info_nh() in include/net/nexthop.h
because we run it on a fib_info with nexthop object. The call chain is:
inet_rtm_delroute -> fib_table_delete -> fib_nh_match (called with a
nexthop fib_info and also with fc_oif set thus calling fib_info_nh on
the fib_info and triggering the warning).
Repro steps:
$ ip nexthop add id 12 via 172.16.1.3 dev veth1
$ ip route add 172.16.101.1/32 nhid 12
$ ip route delete 172.16.101.1/32 dev veth1
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipv4: fix route with nexthop object delete warning
FRR folks have hit a kernel warning[1] while deleting routes[2] which is
caused by trying to delete a route pointing to a nexthop id without
specifying nhid but matching on an interface. That is, a route is found
but we hit a warning while matching it. The warning is from
fib_info_nh() in include/net/nexthop.h because we run it on a fib_info
with nexthop object. The call chain is:
inet_rtm_delroute -> fib_table_delete -> fib_nh_match (called with a
nexthop fib_info and also with fc_oif set thus calling fib_info_nh on
the fib_info and triggering the warning). The fix is to not do any
matching in that branch if the fi has a nexthop object because those are
managed separately. I.e. we should match when deleting without nh spec and
should fail when deleting a nexthop route with old-style nh spec because
nexthop objects are managed separately, e.g.:
$ ip r show 1.2.3.4/32
1.2.3.4 nhid 12 via 192.168.11.2 dev dummy0
$ ip r del 1.2.3.4/32
$ ip r del 1.2.3.4/32 nhid 12
<both should work>
$ ip r del 1.2.3.4/32 dev dummy0
<should fail with ESRCH>
Fixes: f509b32a7223 ("ipv4: Plumb support for nexthop object in a fib_info") Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Fri, 1 Apr 2022 05:42:44 +0000 (22:42 -0700)]
net: micrel: fix KS8851_MLL Kconfig
KS8851_MLL selects MICREL_PHY, which depends on PTP_1588_CLOCK_OPTIONAL,
so make KS8851_MLL also depend on PTP_1588_CLOCK_OPTIONAL since
'select' does not follow any dependency chains.
Fixes kconfig warning and build errors:
WARNING: unmet direct dependencies detected for MICREL_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- KS8851_MLL [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICREL [=y] && HAS_IOMEM [=y]
ld: drivers/net/phy/micrel.o: in function `lan8814_ts_info':
micrel.c:(.text+0xb35): undefined reference to `ptp_clock_index'
ld: drivers/net/phy/micrel.o: in function `lan8814_probe':
micrel.c:(.text+0x2586): undefined reference to `ptp_clock_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Fri, 1 Apr 2022 02:48:44 +0000 (10:48 +0800)]
mctp: Use output netdev to allocate skb headroom
Previously the skb was allocated with headroom MCTP_HEADER_MAXLEN,
but that isn't sufficient if we are using devs that are not MCTP
specific.
This also adds a check that the smctp_halen provided to sendmsg for
extended addressing is the correct size for the netdev.
Fixes: b9ac60078bc1 ("mctp: Populate socket implementation") Reported-by: Matthew Rinaldi <mjrinal@g.clemson.edu> Signed-off-by: Matt Johnston <matt@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Fri, 1 Apr 2022 02:48:43 +0000 (10:48 +0800)]
mctp i2c: correct mctp_i2c_header_create result
header_ops.create should return the length of the header,
instead mctp_i2c_head_create() returned 0.
This didn't cause any problem because the MCTP stack accepted
0 as success.
Fixes: 53abdc527fe3 ("mctp i2c: MCTP I2C binding driver") Signed-off-by: Matt Johnston <matt@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston [Fri, 1 Apr 2022 02:48:42 +0000 (10:48 +0800)]
mctp: Fix check for dev_hard_header() result
dev_hard_header() returns the length of the header, so
we need to test for negative errors rather than non-zero.
Fixes: a358eda10ab4 ("mctp: Add initial routing framework") Signed-off-by: Matt Johnston <matt@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 1 Apr 2022 11:01:38 +0000 (12:01 +0100)]
Merge branch 'ice-fixups'
Tony Nguyen says:
====================
ice-fixups
This series handles a handful of cleanups for the ice
driver. Ivan fixed a problem on the VSI during a release,
fixing a MAC address setting, and a broken IFF_ALLMULTI
handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 31 Mar 2022 16:20:08 +0000 (09:20 -0700)]
ice: Fix broken IFF_ALLMULTI handling
Handling of all-multicast flag and associated multicast promiscuous
mode is broken in ice driver. When an user switches allmulticast
flag on or off the driver checks whether any VLANs are configured
over the interface (except default VLAN 0).
If any extra VLANs are registered it enables multicast promiscuous
mode for all these VLANs (including default VLAN 0) using
ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all
multicast packets tagged with known VLAN ID or untagged are received
and multicast packets tagged with unknown VLAN ID ignored.
If no extra VLANs are registered (so only VLAN 0 exists) it enables
multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC
look-up type. In this situation any multicast packets including
tagged ones are received.
The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:
ice_vsi_sync_fltr() {
...
if (changed_flags & IFF_ALLMULTI) {
if (netdev->flags & IFF_ALLMULTI) {
if (vsi->num_vlans > 1)
ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
} else {
if (vsi->num_vlans > 1)
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
}
}
...
}
The code above depends on value vsi->num_vlan that specifies number
of VLANs configured over the interface (including VLAN 0) and
this is problem because that value is modified in NDO callbacks
ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().
Scenario 1:
1. ip link set ens7f0 allmulticast on
2. ip link add vlan10 link ens7f0 type vlan id 10
3. ip link set ens7f0 allmulticast off
4. ip link set ens7f0 allmulticast on
[1] In this scenario IFF_ALLMULTI is enabled and the driver calls
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs
multicast promisc rule with non-VLAN look-up type.
[2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
[3] Command switches IFF_ALLMULTI off and the driver calls
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this
call is effectively NOP because it looks for multicast promisc
rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such
rules exist. So the all-multicast remains enabled silently
in hardware.
[4] Command tries to switch IFF_ALLMULTI on and the driver calls
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call
fails (-EEXIST) because non-VLAN multicast promisc rule already
exists.
Scenario 2:
1. ip link add vlan10 link ens7f0 type vlan id 10
2. ip link set ens7f0 allmulticast on
3. ip link add vlan20 link ens7f0 type vlan id 20
4. ip link del vlan10 ; ip link del vlan20
5. ip link set ens7f0 allmulticast off
[1] VLAN with ID 10 is added and vsi->num_vlan==2
[2] Command switches IFF_ALLMULTI on and driver installs multicast
promisc rules with VLAN look-up type for VLAN 0 and 10
[3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast
promisc rules is added for this new VLAN so the interface does
not receive MC packets from VLAN 20
[4] Both VLANs are removed but multicast rule for VLAN 10 remains
installed so interface receives multicast packets from VLAN 10
[5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1
the driver tries to remove multicast promisc rule for VLAN 0
with non-VLAN look-up that does not exist.
All-multicast looks disabled from user point of view but it
is partially enabled in HW (interface receives all multicast
packets either untagged or tagged with VLAN ID 10)
To resolve these issues the patch introduces these changes:
1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and
ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed
and IFF_ALLMULTI is enabled an appropriate multicast promisc
rule for that VLAN ID is added/removed.
2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added
so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_VLAN_PROMISC_BITS.
3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed
so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_PROMISC_BITS.
4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY
bit protection to avoid races with ice_vsi_sync_fltr() that runs
in ice_service_task() context.
5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
6. Error messages added to ice_fltr_*_vsi_promisc() helper functions
to avoid them in their callers
7. Small improvements to increase readability
Fixes: 6a1be313400b ("ice: Add support for PF/VF promiscuous mode") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Alice Michael <alice.michael@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 31 Mar 2022 16:20:07 +0000 (09:20 -0700)]
ice: Fix MAC address setting
Commit 8e572b6d1cbe16 ("ice: Remove excess error variables") merged
the usage of 'status' and 'err' variables into single one in
function ice_set_mac_address(). Unfortunately this causes
a regression when call of ice_fltr_add_mac() returns -EEXIST because
this return value does not indicate an error in this case but
value of 'err' remains to be -EEXIST till the end of the function
and is returned to caller.
Prior mentioned commit this does not happen because return value of
ice_fltr_add_mac() was stored to 'status' variable first and
if it was -EEXIST then 'err' remains to be zero.
Fix the problem by reset 'err' to zero when ice_fltr_add_mac()
returns -EEXIST.
Fixes: 8e572b6d1cbe16 ("ice: Remove excess error variables") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Alexander Lobakin <alexandr.lobakin@intel.com> Signed-off-by: Alice Michael <alice.michael@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 31 Mar 2022 16:20:06 +0000 (09:20 -0700)]
ice: Clear default forwarding VSI during VSI release
VSI is set as default forwarding one when promisc mode is set for
PF interface, when PF is switched to switchdev mode or when VF
driver asks to enable allmulticast or promisc mode for the VF
interface (when vf-true-promisc-support priv flag is off).
The third case is buggy because in that case VSI associated with
VF remains as default one after VF removal.
Reproducer:
1. Create VF
echo 1 > sys/class/net/ens7f0/device/sriov_numvfs
2. Enable allmulticast or promisc mode on VF
ip link set ens7f0v0 allmulticast on
ip link set ens7f0v0 promisc on
3. Delete VF
echo 0 > sys/class/net/ens7f0/device/sriov_numvfs
4. Try to enable promisc mode on PF
ip link set ens7f0 promisc on
Although it looks that promisc mode on PF is enabled the opposite
is true because ice_vsi_sync_fltr() responsible for IFF_PROMISC
handling first checks if any other VSI is set as default forwarding
one and if so the function does not do anything. At this point
it is not possible to enable promisc mode on PF without re-probe
device.
To resolve the issue this patch clear default forwarding VSI
during ice_vsi_release() when the VSI to be released is the default
one.
Fixes: c56fdd75db47 ("ice: Add VF promiscuous support") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Alice Michael <alice.michael@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Switch drivers that don't implement ->port_change_mtu() will cause the
DSA master to remain with an MTU of 1500, since we've deleted the other
code path. In turn, this causes a regression for those systems, where
MTU-sized traffic can no longer be terminated.
Revert the change taking into account the fact that rtnl_lock() is now
taken top-level from the callers of dsa_master_setup() and
dsa_master_teardown(). Also add a comment in order for it to be
absolutely clear why it is still needed.
Fixes: 98ec0d0995c0 ("net: dsa: stop updating master MTU from master.c") Reported-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
skbuff: fix coalescing for page_pool fragment recycling
Fix a use-after-free when using page_pool with page fragments. We
encountered this problem during normal RX in the hns3 driver:
(1) Initially we have three descriptors in the RX queue. The first one
allocates PAGE1 through page_pool, and the other two allocate one
half of PAGE2 each. Page references look like this:
In skb_try_coalesce(), __skb_frag_ref() takes a page reference to
PAGE2, where it should instead have increased the page_pool frag
reference, pp_frag_count. Without coalescing, when releasing both
SKB2 and SKB3, a single reference to PAGE2 would be dropped. Now
when releasing SKB1 and SKB2, two references to PAGE2 will be
dropped, resulting in underflow.
(3c) Drop SKB2:
af_packet_rcv(SKB2)
consume_skb(SKB2)
skb_release_data(SKB2) // drops second dataref
page_pool_return_skb_page(PAGE2) // drops one pp_frag_count
SKB1 _____ PAGE1
\____
PAGE2
/
RX_BD3 _________/
(4) Userspace calls recvmsg()
Copies SKB1 and releases it. Since SKB3 was coalesced with SKB1, we
release the SKB3 page as well:
tcp_eat_recv_skb(SKB1)
skb_release_data(SKB1)
page_pool_return_skb_page(PAGE1)
page_pool_return_skb_page(PAGE2) // drops second pp_frag_count
(5) PAGE2 is freed, but the third RX descriptor was still using it!
In our case this causes IOMMU faults, but it would silently corrupt
memory if the IOMMU was disabled.
Change the logic that checks whether pp_recycle SKBs can be coalesced.
We still reject differing pp_recycle between 'from' and 'to' SKBs, but
in order to avoid the situation described above, we also reject
coalescing when both 'from' and 'to' are pp_recycled and 'from' is
cloned.
The new logic allows coalescing a cloned pp_recycle SKB into a page
refcounted one, because in this case the release (4) will drop the right
reference, the one taken by skb_try_coalesce().
Fixes: 2c6f2cc5b8f3 ("page_pool: add frag page recycling support in page pool") Suggested-by: Alexander Duyck <alexanderduyck@fb.com> Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eyal Birger [Thu, 31 Mar 2022 07:26:43 +0000 (10:26 +0300)]
vrf: fix packet sniffing for traffic originating from ip tunnels
in commit b1ab9725d6b0
("vrf: add mac header for tunneled packets when sniffer is attached")
an Ethernet header was cooked for traffic originating from tunnel devices.
However, the header is added based on whether the mac_header is unset
and ignores cases where the device doesn't expose a mac header to upper
layers, such as in ip tunnels like ipip and gre.
Traffic originating from such devices still appears garbled when capturing
on the vrf device.
Fix by observing whether the original device exposes a header to upper
layers, similar to the logic done in af_packet.
In addition, skb->mac_len needs to be adjusted after adding the Ethernet
header for the skb_push/pull() surrounding dev_queue_xmit_nit() to work
on these packets.
Fixes: b1ab9725d6b0 ("vrf: add mac header for tunneled packets when sniffer is attached") Signed-off-by: Eyal Birger <eyal.birger@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ziyang Xuan [Thu, 31 Mar 2022 07:04:28 +0000 (15:04 +0800)]
net/tls: fix slab-out-of-bounds bug in decrypt_internal
The memory size of tls_ctx->rx.iv for AES128-CCM is 12 setting in
tls_set_sw_offload(). The return value of crypto_aead_ivsize()
for "ccm(aes)" is 16. So memcpy() require 16 bytes from 12 bytes
memory space will trigger slab-out-of-bounds bug as following:
==================================================================
BUG: KASAN: slab-out-of-bounds in decrypt_internal+0x385/0xc40 [tls]
Read of size 16 at addr ffff888114e84e60 by task tls/10911
Replace the crypto_aead_ivsize() with prot->iv_size + prot->salt_size
when memcpy() iv value in TLS_1_3_VERSION scenario.
Fixes: 75c85ed6019e ("net/tls: Add support of AES128-CCM based ciphers") Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Wed, 30 Mar 2022 16:37:03 +0000 (16:37 +0000)]
net: sfc: add missing xdp queue reinitialization
After rx/tx ring buffer size is changed, kernel panic occurs when
it acts XDP_TX or XDP_REDIRECT.
When tx/rx ring buffer size is changed(ethtool -G), sfc driver
reallocates and reinitializes rx and tx queues and their buffer
(tx_queue->buffer).
But it misses reinitializing xdp queues(efx->xdp_tx_queues).
So, while it is acting XDP_TX or XDP_REDIRECT, it uses the uninitialized
tx_queue->buffer.
A new function efx_set_xdp_channels() is separated from efx_set_channels()
to handle only xdp queues.
Fixes: dc1c0a923867 ("sfc: allocate channels for XDP tx queues") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 31 Mar 2022 18:23:31 +0000 (11:23 -0700)]
Merge tag 'net-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull more networking updates from Jakub Kicinski:
"Networking fixes and rethook patches.
Features:
- kprobes: rethook: x86: replace kretprobe trampoline with rethook
Current release - regressions:
- sfc: avoid null-deref on systems without NUMA awareness in the new
queue sizing code
Current release - new code bugs:
- vxlan: do not feed vxlan_vnifilter_dump_dev with non-vxlan devices
- eth: lan966x: fix null-deref on PHY pointer in timestamp ioctl when
interface is down
Previous releases - always broken:
- openvswitch: correct neighbor discovery target mask field in the
flow dump
- wireguard: ignore v6 endpoints when ipv6 is disabled and fix a leak
- rxrpc: fix call timer start racing with call destruction
- rxrpc: fix null-deref when security type is rxrpc_no_security
- can: fix UAF bugs around echo skbs in multiple drivers
Misc:
- docs: move netdev-FAQ to the 'process' section of the
documentation"
* tag 'net-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
vxlan: do not feed vxlan_vnifilter_dump_dev with non vxlan devices
openvswitch: Add recirc_id to recirc warning
rxrpc: fix some null-ptr-deref bugs in server_key.c
rxrpc: Fix call timer start racing with call destruction
net: hns3: fix software vlan talbe of vlan 0 inconsistent with hardware
net: hns3: fix the concurrency between functions reading debugfs
docs: netdev: move the netdev-FAQ to the process pages
docs: netdev: broaden the new vs old code formatting guidelines
docs: netdev: call out the merge window in tag checking
docs: netdev: add missing back ticks
docs: netdev: make the testing requirement more stringent
docs: netdev: add a question about re-posting frequency
docs: netdev: rephrase the 'should I update patchwork' question
docs: netdev: rephrase the 'Under review' question
docs: netdev: shorten the name and mention msgid for patch status
docs: netdev: note that RFC postings are allowed any time
docs: netdev: turn the net-next closed into a Warning
docs: netdev: move the patch marking section up
docs: netdev: minor reword
docs: netdev: replace references to old archives
...
Eric Dumazet [Wed, 30 Mar 2022 19:46:43 +0000 (12:46 -0700)]
vxlan: do not feed vxlan_vnifilter_dump_dev with non vxlan devices
vxlan_vnifilter_dump_dev() assumes it is called only
for vxlan devices. Make sure it is the case.
BUG: KASAN: slab-out-of-bounds in vxlan_vnifilter_dump_dev+0x9a0/0xb40 drivers/net/vxlan/vxlan_vnifilter.c:349
Read of size 4 at addr ffff888060d1ce70 by task syz-executor.3/17662
Jakub Kicinski [Thu, 31 Mar 2022 15:36:17 +0000 (08:36 -0700)]
Merge tag 'linux-can-fixes-for-5.18-20220331' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-03-31
The first patch is by Oliver Hartkopp and fixes MSG_PEEK feature in
the CAN ISOTP protocol (broken in net-next for v5.18 only).
Tom Rix's patch for the mcp251xfd driver fixes the propagation of an
error value in case of an error.
A patch by me for the m_can driver fixes a use-after-free in the xmit
handler for m_can IP cores v3.0.x.
Hangyu Hua contributes 3 patches fixing the same double free in the
error path of the xmit handler in the ems_usb, usb_8dev and mcba_usb
USB CAN driver.
Pavel Skripkin contributes a patch for the mcba_usb driver to properly
check the endpoint type.
The last patch is by me and fixes a mem leak in the gs_usb, which was
introduced in net-next for v5.18.
* tag 'linux-can-fixes-for-5.18-20220331' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: gs_usb: gs_make_candev(): fix memory leak for devices with extended bit timing configuration
can: mcba_usb: properly check endpoint type
can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path
can: usb_8dev: usb_8dev_start_xmit(): fix double dev_kfree_skb() in error path
can: ems_usb: ems_usb_start_xmit(): fix double dev_kfree_skb() in error path
can: m_can: m_can_tx_handler(): fix use after free of skb
can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix return of error value
can: isotp: restore accidentally removed MSG_PEEK feature
====================
Xiaolong Huang [Wed, 30 Mar 2022 14:22:14 +0000 (15:22 +0100)]
rxrpc: fix some null-ptr-deref bugs in server_key.c
Some function calls are not implemented in rxrpc_no_security, there are
preparse_server_key, free_preparse_server_key and destroy_server_key.
When rxrpc security type is rxrpc_no_security, user can easily trigger a
null-ptr-deref bug via ioctl. So judgment should be added to prevent it
David Howells [Wed, 30 Mar 2022 14:39:16 +0000 (15:39 +0100)]
rxrpc: Fix call timer start racing with call destruction
The rxrpc_call struct has a timer used to handle various timed events
relating to a call. This timer can get started from the packet input
routines that are run in softirq mode with just the RCU read lock held.
Unfortunately, because only the RCU read lock is held - and neither ref or
other lock is taken - the call can start getting destroyed at the same time
a packet comes in addressed to that call. This causes the timer - which
was already stopped - to get restarted. Later, the timer dispatch code may
then oops if the timer got deallocated first.
Fix this by trying to take a ref on the rxrpc_call struct and, if
successful, passing that ref along to the timer. If the timer was already
running, the ref is discarded.
The timer completion routine can then pass the ref along to the call's work
item when it queues it. If the timer or work item where already
queued/running, the extra ref is discarded.
Guangbin Huang [Wed, 30 Mar 2022 13:45:06 +0000 (21:45 +0800)]
net: hns3: fix software vlan talbe of vlan 0 inconsistent with hardware
When user delete vlan 0, as driver will not delete vlan 0 for hardware in
function hclge_set_vlan_filter_hw(), so vlan 0 in software vlan talbe should
not be deleted.
Fixes: f94c04540221 ("net: hns3: sync VLAN filter entries when kill VLAN ID failed") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Yufeng Mo [Wed, 30 Mar 2022 13:45:05 +0000 (21:45 +0800)]
net: hns3: fix the concurrency between functions reading debugfs
Currently, the debugfs mechanism is that all functions share a
global variable to save the pointer for obtaining data. When
different functions concurrently access the same file node,
repeated release exceptions occur. Therefore, the granularity
of the pointer for storing the obtained data is adjusted to be
private for each function.
Fixes: 9ac2271d66e1 ("net: hns3: refactor the debugfs process") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
====================
docs: update and move the netdev-FAQ
A section of documentation for tree-specific process quirks had
been created a while back. There's only one tree in it, so far,
the tip tree, but the contents seem to answer similar questions
as we answer in the netdev-FAQ. Move the netdev-FAQ.
Take this opportunity to touch up and update a few sections.
v3: remove some confrontational? language from patch 7
v2: remove non-git in patch 3
add patch 5
====================
Jakub Kicinski [Wed, 30 Mar 2022 04:24:54 +0000 (21:24 -0700)]
docs: netdev: move the patch marking section up
We want people to mark their patches with net and net-next in the subject.
Many miss doing that. Move the FAQ section which points that out up, and
place it after the section which enumerates the trees, that seems like
a pretty logical place for it. Since the two sections are together we
can remove a little bit (not too much) of the repetition.
v2: also remove the text for non-git setups, we want people to use git.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
can: gs_usb: gs_make_candev(): fix memory leak for devices with extended bit timing configuration
Some CAN-FD capable devices offer extended bit timing information for
the data bit timing. The information must be read with an USB control
message. The memory for this message is allocated but not free()ed (in
the non error case). This patch adds the missing free.
Pavel Skripkin [Sun, 13 Mar 2022 10:09:03 +0000 (13:09 +0300)]
can: mcba_usb: properly check endpoint type
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. We should check that in endpoint is actually present to
prevent this warning.
Found pipes are now saved to struct mcba_priv and code uses them
directly instead of making pipes in place.
Fixes: 8f19e8a05eae ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Link: https://lore.kernel.org/all/20220313100903.10868-1-paskripkin@gmail.com Reported-and-tested-by: syzbot+3bc1dce0cc0052d60fde@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Hangyu Hua [Fri, 11 Mar 2022 08:02:08 +0000 (16:02 +0800)]
can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path
There is no need to call dev_kfree_skb() when usb_submit_urb() fails
because can_put_echo_skb() deletes original skb and
can_free_echo_skb() deletes the cloned skb.
Hangyu Hua [Fri, 11 Mar 2022 08:06:14 +0000 (16:06 +0800)]
can: usb_8dev: usb_8dev_start_xmit(): fix double dev_kfree_skb() in error path
There is no need to call dev_kfree_skb() when usb_submit_urb() fails
because can_put_echo_skb() deletes original skb and
can_free_echo_skb() deletes the cloned skb.
Fixes: 633e75d8c39a ("can: usb_8dev: Add support for USB2CAN interface from 8 devices") Link: https://lore.kernel.org/all/20220311080614.45229-1-hbh25y@gmail.com Cc: stable@vger.kernel.org Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Hangyu Hua [Mon, 28 Feb 2022 08:36:39 +0000 (16:36 +0800)]
can: ems_usb: ems_usb_start_xmit(): fix double dev_kfree_skb() in error path
There is no need to call dev_kfree_skb() when usb_submit_urb() fails
beacause can_put_echo_skb() deletes the original skb and
can_free_echo_skb() deletes the cloned skb.
Link: https://lore.kernel.org/all/20220228083639.38183-1-hbh25y@gmail.com Fixes: 07edeffafb68 ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface") Cc: stable@vger.kernel.org Cc: Sebastian Haas <haas@ems-wuensche.com> Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: m_can: m_can_tx_handler(): fix use after free of skb
can_put_echo_skb() will clone skb then free the skb. Move the
can_put_echo_skb() for the m_can version 3.0.x directly before the
start of the xmit in hardware, similar to the 3.1.x branch.
Tom Rix [Sat, 19 Mar 2022 15:31:28 +0000 (08:31 -0700)]
can: mcp251xfd: mcp251xfd_register_get_dev_id(): fix return of error value
Clang static analysis reports this issue:
| mcp251xfd-core.c:1813:7: warning: The left operand
| of '&' is a garbage value
| FIELD_GET(MCP251XFD_REG_DEVID_ID_MASK, dev_id),
| ^ ~~~~~~
dev_id is set in a successful call to mcp251xfd_register_get_dev_id().
Though the status of calls made by mcp251xfd_register_get_dev_id() are
checked and handled, their status' are not returned. So return err.
In commit fc89b17fe0ae ("can: isotp: support MSG_TRUNC flag when
reading from socket") a new check for recvmsg flags has been
introduced that only checked for the flags that are handled in
isotp_recvmsg() itself.
This accidentally removed the MSG_PEEK feature flag which is processed
later in the call chain in __skb_try_recv_from_queue().
Add MSG_PEEK to the set of valid flags to restore the feature.
Randy Dunlap [Wed, 30 Mar 2022 01:20:25 +0000 (18:20 -0700)]
net: sparx5: uses, depends on BRIDGE or !BRIDGE
Fix build errors when BRIDGE=m and SPARX5_SWITCH=y:
riscv64-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.o: in function `.L305':
sparx5_switchdev.c:(.text+0xdb0): undefined reference to `br_vlan_enabled'
riscv64-linux-ld: drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.o: in function `.L283':
sparx5_switchdev.c:(.text+0xee0): undefined reference to `br_vlan_enabled'
Fixes: 96594a6222c1 ("net: sparx5: add the basic sparx5 driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Horatiu Vultur <horatiu.vultur@microchip.com> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/20220330012025.29560-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 31 Mar 2022 02:14:11 +0000 (19:14 -0700)]
Merge branch 'wireguard-patches-for-5-18-rc1'
Jason A. Donenfeld says:
====================
wireguard patches for 5.18-rc1
Here's a small set of fixes for the next net push:
1) Pipacs reported a CFI violation in a cleanup routine, which he
triggered using grsec's RAP. I haven't seen reports of this yet from
the Android/CFI world yet, but it's only a matter of time there.
2) A small rng cleanup to the self test harness to make it initialize
faster on 5.18.
3) Wang reported and fixed a skb leak for CONFIG_IPV6=n.
4) After Wang's fix for the direct leak, I investigated how that code
path even could be hit, and found that the netlink layer still
handles IPv6 endpoints, when it probably shouldn't.
====================
wireguard: socket: ignore v6 endpoints when ipv6 is disabled
The previous commit fixed a memory leak on the send path in the event
that IPv6 is disabled at compile time, but how did a packet even arrive
there to begin with? It turns out we have previously allowed IPv6
endpoints even when IPv6 support is disabled at compile time. This is
awkward and inconsistent. Instead, let's just ignore all things IPv6,
the same way we do other malformed endpoints, in the case where IPv6 is
disabled.
Fixes: 0c73bbc77a76 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In function wg_socket_send_buffer_as_reply_to_skb() or wg_socket_send_
buffer_to_peer(), the semantics of send6() is required to free skb. But
when CONFIG_IPV6 is disable, kfree_skb() is missing. This patch adds it
to fix this bug.
Signed-off-by: Wang Hai <wanghai38@huawei.com> Fixes: 0c73bbc77a76 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The seed_rng() function was written to work across lots of old kernels,
back when WireGuard used a big compatibility layer. Now that things have
evolved, we can vastly simplify this, by just marking the RNG as seeded.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
wireguard: queueing: use CFI-safe ptr_ring cleanup function
We make too nuanced use of ptr_ring to entirely move to the skb_array
wrappers, but we at least should avoid the naughty function pointer cast
when cleaning up skbs. Otherwise RAP/CFI will honk at us. This patch
uses the __skb_array_destroy_skb wrapper for the cleanup, rather than
directly providing kfree_skb, which is what other drivers in the same
situation do too.
Reported-by: PaX Team <pageexec@freemail.hu> Fixes: 8ab51af1e9d9 ("wireguard: receive: use ring buffer for incoming handshakes") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Wed, 30 Mar 2022 22:11:26 +0000 (15:11 -0700)]
Merge tag 'for-5.18/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc architecture updates from Helge Deller:
- Revert a patch to the invalidate/flush vmap routines which broke
kernel patching functions on older PA-RISC machines.
- Fix the kernel patching code wrt locking and flushing. Works now on
B160L machine as well.
- Fix CPU IRQ affinity for LASI, WAX and Dino chips
- Add CPU hotplug support
- Detect the hppa-suse-linux-gcc compiler when cross-compiling
* tag 'for-5.18/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix patch code locking and flushing
parisc: Find a new timesync master if current CPU is removed
parisc: Move common_stext into .text section when CONFIG_HOTPLUG_CPU=y
parisc: Rewrite arch_cpu_idle_dead() for CPU hotplugging
parisc: Implement __cpu_die() and __cpu_disable() for CPU hotplugging
parisc: Add PDC locking functions for rendezvous code
parisc: Move disable_sr_hashing_asm() into .text section
parisc: Move CPU startup-related functions into .text section
parisc: Move store_cpu_topology() into text section
parisc: Switch from GENERIC_CPU_DEVICES to GENERIC_ARCH_TOPOLOGY
parisc: Ensure set_firmware_width() is called only once
parisc: Add constants for control registers and clean up mfctl()
parisc: Detect hppa-suse-linux-gcc compiler for cross-building
parisc: Clean up cpu_check_affinity() and drop cpu_set_affinity_irq()
parisc: Fix CPU affinity for Lasi, WAX and Dino chips
Revert "parisc: Fix invalidate/flush vmap routines"
Linus Torvalds [Wed, 30 Mar 2022 22:06:31 +0000 (15:06 -0700)]
Merge tag 'modules-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module update from Luis Chamberlain:
"There is only one patch which qualifies for modules for v5.18-rc1 and
its a small fix from Dan Carpenter for lib/test_kmod module.
The rest of the changes are too major and landed in modules-testing
too late for inclusion. The good news is that most of the major
changes for v5.19 is going to be tested very early through linux-next.
This simple fix is all we have for modules for v5.18-rc1"
* tag 'modules-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
lib/test: use after free in register_test_dev_kmod()
Martin Habets [Tue, 29 Mar 2022 16:07:49 +0000 (17:07 +0100)]
sfc: Avoid NULL pointer dereference on systems without numa awareness
On such systems cpumask_of_node() returns NULL, which bitmap
operations are not happy with.
Fixes: 32b57c7da690 ("sfc: default config to 1 channel/core in local NUMA node only") Fixes: af83ef65bdaf ("sfc: set affinity hints in local NUMA node only") Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com> Reviewed-by: Íñigo Huguet <ihuguet@redhat.com> Link: https://lore.kernel.org/r/164857006953.8140.3265568858101821256.stgit@palantir17.mph.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zheng Yongjun [Tue, 29 Mar 2022 09:08:00 +0000 (09:08 +0000)]
net: dsa: felix: fix possible NULL pointer dereference
As the possible failure of the allocation, kzalloc() may return NULL
pointer.
Therefore, it should be better to check the 'sgi' in order to prevent
the dereference of NULL pointer.
Fixes: 06858e362bbad ("net: dsa: felix: add stream gate settings for psfp"). Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220329090800.130106-1-zhengyongjun3@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Wed, 30 Mar 2022 18:00:33 +0000 (11:00 -0700)]
Merge tag 'pwm/for-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains conversions of some more drivers to the atomic API as
well as the addition of new chip support for some existing drivers.
There are also various minor fixes and cleanups across the board, from
drivers to device tree bindings"
* tag 'pwm/for-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (45 commits)
pwm: rcar: Simplify multiplication/shift logic
dt-bindings: pwm: renesas,tpu: Do not require pwm-cells twice
dt-bindings: pwm: tiehrpwm: Do not require pwm-cells twice
dt-bindings: pwm: tiecap: Do not require pwm-cells twice
dt-bindings: pwm: samsung: Do not require pwm-cells twice
dt-bindings: pwm: intel,keembay: Do not require pwm-cells twice
dt-bindings: pwm: brcm,bcm7038: Do not require pwm-cells twice
dt-bindings: pwm: toshiba,visconti: Include generic PWM schema
dt-bindings: pwm: renesas,pwm: Include generic PWM schema
dt-bindings: pwm: sifive: Include generic PWM schema
dt-bindings: pwm: rockchip: Include generic PWM schema
dt-bindings: pwm: mxs: Include generic PWM schema
dt-bindings: pwm: iqs620a: Include generic PWM schema
dt-bindings: pwm: intel,lgm: Include generic PWM schema
dt-bindings: pwm: imx: Include generic PWM schema
dt-bindings: pwm: allwinner,sun4i-a10: Include generic PWM schema
pwm: pwm-mediatek: Beautify error messages text
pwm: pwm-mediatek: Allocate clk_pwms with devm_kmalloc_array
pwm: pwm-mediatek: Simplify error handling with dev_err_probe()
pwm: brcmstb: Remove useless locking
...
Linus Torvalds [Wed, 30 Mar 2022 17:58:28 +0000 (10:58 -0700)]
Merge tag 'regulator-fix-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of fixes for the rt4831 driver which fix features that didn't
work due to incomplete description of the register configuration"
* tag 'regulator-fix-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: rt4831: Add active_discharge_on to fix discharge API
regulator: rt4831: Add bypass mask to fix set_bypass API work
Linus Torvalds [Wed, 30 Mar 2022 17:54:49 +0000 (10:54 -0700)]
Merge tag 'dmaengine-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"This time we have bunch of driver updates and some new device support.
New support:
- Document RZ/V2L and RZ/G2UL dma binding
- TI AM62x k3-udma and k3-psil support
Updates:
- Yaml conversion for Mediatek uart apdma schema
- Removal of DMA-32 fallback configuration for various drivers
- imx-sdma updates for channel restart"
* tag 'dmaengine-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (23 commits)
dmaengine: hisi_dma: fix MSI allocate fail when reload hisi_dma
dmaengine: dw-axi-dmac: cleanup comments
dmaengine: fsl-dpaa2-qdma: Drop comma after SoC match table sentinel
dt-bindings: dma: Convert mtk-uart-apdma to DT schema
dmaengine: ppc4xx: Make use of the helper macro LIST_HEAD()
dmaengine: idxd: Remove useless DMA-32 fallback configuration
dmaengine: qcom_hidma: Remove useless DMA-32 fallback configuration
dmaengine: sh: Kconfig: Add ARCH_R9A07G054 dependency for RZ_DMAC config option
dmaengine: ti: k3-psil: Add AM62x PSIL and PDMA data
dmaengine: ti: k3-udma: Add AM62x DMSS support
dmaengine: ti: cleanup comments
dmaengine: imx-sdma: clean up some inconsistent indenting
dmaengine: Revert "dmaengine: shdma: Fix runtime PM imbalance on error"
dmaengine: idxd: restore traffic class defaults after wq reset
dmaengine: altera-msgdma: Remove useless DMA-32 fallback configuration
dmaengine: stm32-dma: set dma_device max_sg_burst
dmaengine: imx-sdma: fix cyclic buffer race condition
dmaengine: imx-sdma: restart cyclic channel if needed
dmaengine: iot: Remove useless DMA-32 fallback configuration
dmaengine: ptdma: handle the cases based on DMA is complete
...
Linus Torvalds [Wed, 30 Mar 2022 17:50:48 +0000 (10:50 -0700)]
Merge tag 'rproc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
"In the remoteproc core, it's now possible to mark the sysfs attributes
read only on a per-instance basis, which is then used by the TI wkup
M3 driver.
Also, the rproc_shutdown() interface propagates errors to the caller
and an array underflow is fixed in the debugfs interface. The
rproc_da_to_va() API is moved to the public API to allow e.g. child
rpmsg devices to acquire pointers to memory shared with the remote
processor.
The TI K3 R5F and DSP drivers gains support for attaching to instances
already started by the bootloader, aka IPC-only mode.
The Mediatek remoteproc driver gains support for the MT8186 SCP. The
driver's probe function is reordered and moved to use the devres
version of rproc_alloc() to save a few gotos. The driver's probe
function is also transitioned to use dev_err_probe() to provide better
debug support.
Support for the Qualcomm SC7280 Wireless Subsystem (WPSS) is
introduced. The Hexagon based remoteproc drivers gains support for
voting for interconnect bandwidth during launch of the remote
processor. The modem subsystem (MSS) driver gains support for probing
the BAM-DMUX driver, which provides the network interface towards the
modem on a set of older Qualcomm platforms. In addition a number a bug
fixes are introduces in the Qualcomm drivers.
Lastly Qualcomm ADSP DeviceTree binding is converted to YAML format,
to allow validation of DeviceTree source files"
* tag 'rproc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (22 commits)
remoteproc: qcom_q6v5_mss: Create platform device for BAM-DMUX
remoteproc: qcom: q6v5_wpss: Add support for sc7280 WPSS
dt-bindings: remoteproc: qcom: Add SC7280 WPSS support
dt-bindings: remoteproc: qcom: adsp: Convert binding to YAML
remoteproc: k3-dsp: Add support for IPC-only mode for all K3 DSPs
remoteproc: k3-dsp: Refactor mbox request code in start
remoteproc: k3-r5: Add support for IPC-only mode for all R5Fs
remoteproc: k3-r5: Refactor mbox request code in start
remoteproc: Change rproc_shutdown() to return a status
remoteproc: qcom: q6v5: Add interconnect path proxy vote
remoteproc: mediatek: Support mt8186 scp
dt-bindings: remoteproc: mediatek: Add binding for mt8186 scp
remoteproc: qcom_q6v5_mss: Fix some leaks in q6v5_alloc_memory_region
remoteproc: qcom_wcnss: Add missing of_node_put() in wcnss_alloc_memory_region
remoteproc: qcom: Fix missing of_node_put in adsp_alloc_memory_region
remoteproc: move rproc_da_to_va declaration to remoteproc.h
remoteproc: wkup_m3: Set sysfs_read_only flag
remoteproc: Introduce sysfs_read_only flag
remoteproc: Fix count check in rproc_coredump_write()
remoteproc: mtk_scp: Use dev_err_probe() where possible
...
Linus Torvalds [Wed, 30 Mar 2022 17:47:48 +0000 (10:47 -0700)]
Merge tag 'hwlock-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull hwspinlock updates from Bjorn Andersson:
"This updates sprd and srm32 drivers to use struct_size() instead of
their open-coded equivalents. It also cleans up the omap dt-bindings
example"
* tag 'hwlock-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
hwspinlock: sprd: Use struct_size() helper in devm_kzalloc()
hwspinlock: stm32: Use struct_size() helper in devm_kzalloc()
dt-bindings: hwlock: omap: Remove redundant binding example
Linus Torvalds [Wed, 30 Mar 2022 17:43:19 +0000 (10:43 -0700)]
Merge tag 'rpmsg-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull rpmsg updates from Bjorn Andersson:
"The major part of the rpmsg changes for v5.18 relates to improvements
in the rpmsg char driver, which now allow automatically attaching to
rpmsg channels as well as initiating new communication channels from
the Linux side.
The SMD driver is moved to arch_initcall with the purpose of
registering root clocks earlier during boot.
Also in the SMD driver, a workaround for the resource power management
(RPM) channel is introduced to resolve an issue where both the RPM and
Linux side waits for the other to close the communication established
by the bootloader - this unblocks support for clocks and regulators on
some older Qualcomm platforms"
* tag 'rpmsg-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
rpmsg: ctrl: Introduce new RPMSG_CREATE/RELEASE_DEV_IOCTL controls
rpmsg: char: Introduce the "rpmsg-raw" channel
rpmsg: char: Add possibility to use default endpoint of the rpmsg device
rpmsg: char: Refactor rpmsg_chrdev_eptdev_create function
rpmsg: Update rpmsg_chrdev_register_device function
rpmsg: Move the rpmsg control device from rpmsg_char to rpmsg_ctrl
rpmsg: Create the rpmsg class in core instead of in rpmsg char
rpmsg: char: Export eptdev create and destroy functions
rpmsg: char: treat rpmsg_trysend() ENOMEM as EAGAIN
rpmsg: qcom_smd: Fix redundant channel->registered assignment
rpmsg: use struct_size over open coded arithmetic
rpmsg: smd: allow opening rpm_requests even if already opened
rpmsg: qcom_smd: Promote to arch_initcall
Linus Torvalds [Wed, 30 Mar 2022 17:36:41 +0000 (10:36 -0700)]
Merge tag 'i3c/for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
- support dynamic addition of i2c devices
* tag 'i3c/for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: fix uninitialized variable use in i2c setup
i3c: support dynamically added i2c devices
i3c: remove i2c board info from i2c_dev_desc
Linus Torvalds [Wed, 30 Mar 2022 17:11:04 +0000 (10:11 -0700)]
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There's one large change in the core clk framework here. We change how
clk_set_rate_range() works so that the frequency is re-evaulated each
time the rate is changed. Previously we wouldn't let clk providers see
a rate that was different if it was still within the range, which
could be bad for power if the clk could run slower when a range
expands. Now the clk provider can decide to do something differently
when the constraints change. This broke Nvidia's clk driver so we had
to wait for the fix for that to bake a little more in -next.
The rate range patch series also introduced a kunit suite for the clk
framework that we're going to extend in the next release. It already
made it easy to find corner cases in the rate range patches so I'm
excited to see it cover more clk code and increase our confidence in
core framework patches in the future. I also added a kunit test for
the basic clk gate code and that work will continue to cover more
basic clk types: muxes, dividers, etc.
Beyond the core code we have the usual set of clk driver updates and
additions. Qualcomm again dominates the diffstat here with lots more
SoCs being supported and i.MX follows afer that with a similar number
of SoCs gaining clk drivers. Beyond those large additions there's
drivers being modernized to use clk_parent_data so we can move away
from global string names for all the clks in an SoC. Finally there's
lots of little fixes all over the clk drivers for typos, warnings, and
missing clks that aren't critical and get batched up waiting for the
next merge window to open. Nothing super big stands out in the driver
pile. Full details are below.
Core:
- Make clk_set_rate_range() re-evaluate the limits each time
- Introduce various clk_set_rate_range() tests
- Add clk_drop_range() to drop a previously set range
New Drivers:
- i.MXRT1050 clock driver and bindings
- i.MX8DXL clock driver and bindings
- i.MX93 clock driver and bindings
- NCO blocks on Apple SoCs
- Audio clks on StarFive JH7100 RISC-V SoC
- Add support for the new Renesas RZ/V2L SoC
- Qualcomm SDX65 A7 PLL
- Qualcomm SM6350 GPU clks
- Qualcomm SM6125, SM6350, QCS2290 display clks
- Qualcomm MSM8226 multimedia clks
Updates:
- Kunit tests for clk-gate implementation
- Terminate arrays with sentinels and make that clearer
- Cleanup SPDX tags
- Fix typos in comments
- Mark mux table as const in clk-mux
- Make the all_lists array const
- Convert Cirrus Logic CS2000P driver to regmap, yamlify DT binding
and add support for dynamic mode
- Clock configuration on Microchip PolarFire SoCs
- Free allocations on probe error in Mediatek clk driver
- Modernize Mediatek clk driver by consolidating code
- Add watchdog (WDT), I2C, and pin function controller (PFC) clocks
on Renesas R-Car S4-8
- Improve the clocks for the Rockchip rk3568 display outputs
(parenting, pll-rates)
- Use of_device_get_match_data() instead of open-coding on Rockchip
rk3568
- Reintroduce the expected fractional-divider behaviour that
disappeared with the addition of CLK_FRAC_DIVIDER_POWER_OF_TWO_PS
- Remove SYS PLL 1/2 clock gates for i.MX8M*
- Remove AUDIO MCLK ROOT from i.MX7D
- Add fracn gppll clock type used by i.MX93
- Add new composite clock for i.MX93
- Add missing media mipi phy ref clock for i.MX8MP
- Fix off by one in imx_lpcg_parse_clks_from_dt()
- Rework for the imx pll14xx
- sama7g5: One low priority fix for GCLK of PDMC
- Add DMA engine (SYS-DMAC) clocks on Renesas R-Car S4-8
- Add MOST (MediaLB I/F) clocks on Renesas R-Car E3 and D3
- Add CAN-FD clocks on Renesas R-Car V3U
- Qualcomm SC8280XP RPMCC
- Add some missing clks on Qualcomm MSM8992/MSM8994/MSM8998 SoCs
- Rework Qualcomm GCC bindings and convert SDM845 camera bindig to
YAML
- Convert various Qualcomm drivers to use clk_parent_data
- Remove test clocks from various Qualcomm drivers
- Crypto engine clks on Qualcomm IPQ806x + more freqs for SDCC/NSS
- Qualcomm SM8150 EMAC, PCIe, UFS GDSCs
- Better pixel clk frequency support on Qualcomm RCG2 clks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: zynq: Update the parameters to zynq_clk_register_periph_clk
clk: zynq: trivial warning fix
clk: Drop the rate range on clk_put()
clk: test: Test clk_set_rate_range on orphan mux
clk: Initialize orphan req_rate
dt-bindings: clock: drop useless consumer example
dt-bindings: clock: renesas: Make example 'clocks' parsable
clk: qcom: gcc-msm8994: Fix gpll4 width
dt-bindings: clock: fix dt_binding_check error for qcom,gcc-other.yaml
clk: rs9: Add Renesas 9-series PCIe clock generator driver
clk: fixed-factor: Introduce devm_clk_hw_register_fixed_factor_index()
clk: visconti: prevent array overflow in visconti_clk_register_gates()
dt-bindings: clk: rs9: Add Renesas 9-series I2C PCIe clock generator
clk: sifive: Move all stuff into SoCs header files from C files
clk: sifive: Add SoCs prefix in each SoCs-dependent data
riscv: dts: Change the macro name of prci in each device node
dt-bindings: change the macro name of prci in header files and example
clk: sifive: duplicate the macro definitions for the time being
clk: qcom: sm6125-gcc: fix typos in comments
clk: ti: clkctrl: fix typos in comments
...
Linus Torvalds [Wed, 30 Mar 2022 17:04:11 +0000 (10:04 -0700)]
Merge tag 'libnvdimm-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"The update for this cycle includes the deprecation of block-aperture
mode and a new perf events interface for the papr_scm nvdimm driver.
The perf events approach was acked by PeterZ.
- Add perf support for nvdimm events, initially only for 'papr_scm'
devices.
- Deprecate the 'block aperture' support in libnvdimm, it only ever
existed in the specification, not in shipping product"
* tag 'libnvdimm-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm/blk: Fix title level
MAINTAINERS: remove section LIBNVDIMM BLK: MMIO-APERTURE DRIVER
powerpc/papr_scm: Fix build failure when
drivers/nvdimm: Fix build failure when CONFIG_PERF_EVENTS is not set
nvdimm/region: Delete nd_blk_region infrastructure
ACPI: NFIT: Remove block aperture support
nvdimm/namespace: Delete nd_namespace_blk
nvdimm/namespace: Delete blk namespace consideration in shared paths
nvdimm/blk: Delete the block-aperture window driver
nvdimm/region: Fix default alignment for small regions
docs: ABI: sysfs-bus-nvdimm: Document sysfs event format entries for nvdimm pmu
powerpc/papr_scm: Add perf interface support
drivers/nvdimm: Add perf interface to expose nvdimm performance stats
drivers/nvdimm: Add nvdimm pmu structure
Linus Torvalds [Wed, 30 Mar 2022 06:29:18 +0000 (23:29 -0700)]
fs: fix fd table size alignment properly
Jason Donenfeld reports that my commit dce3bbef012e ("fs: fd tables have
to be multiples of BITS_PER_LONG") doesn't work, and the reason is an
embarrassing brown-paper-bag bug.
Yes, we want to align the number of fds to BITS_PER_LONG, and yes, the
reason they might not be aligned is because the incoming 'max_fd'
argument might not be aligned.
But aligining the argument - while simple - will cause a "infinitely
big" maxfd (eg NR_OPEN_MAX) to just overflow to zero. Which most
definitely isn't what we want either.
The obvious fix was always just to do the alignment last, but I had
moved it earlier just to make the patch smaller and the code look
simpler. Duh. It certainly made _me_ look simple.
Fixes: dce3bbef012e ("fs: fd tables have to be multiples of BITS_PER_LONG") Reported-and-tested-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Fedor Pchelkin <aissur0002@gmail.com> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Christian Brauner <brauner@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've added 16 non-merge commits during the last 1 day(s) which contain
a total of 24 files changed, 354 insertions(+), 187 deletions(-).
The main changes are:
1) x86 specific bits of fprobe/rethook, from Masami and Peter.
2) ice/xsk fixes, from Maciej and Magnus.
3) Various small fixes, from Andrii, Yonghong, Geliang and others.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Fix clang compilation errors
ice: xsk: Fix indexing in ice_tx_xsk_pool()
ice: xsk: Stop Rx processing when ntc catches ntu
ice: xsk: Eliminate unnecessary loop iteration
xsk: Do not write NULL in SW ring at allocation failure
x86,kprobes: Fix optprobe trampoline to generate complete pt_regs
x86,rethook: Fix arch_rethook_trampoline() to generate a complete pt_regs
x86,rethook,kprobes: Replace kretprobe with rethook on x86
kprobes: Use rethook for kretprobe if possible
bpftool: Fix generated code in codegen_asserts
selftests/bpf: fix selftest after random: Urandom_read tracepoint removal
bpf: Fix maximum permitted number of arguments check
bpf: Sync comments for bpf_get_stack
fprobe: Fix sparse warning for acccessing __rcu ftrace_hash
fprobe: Fix smatch type mismatch warning
bpf/bpftool: Add unprivileged_bpf_disabled check against value of 2
====================
Linus Torvalds [Wed, 30 Mar 2022 01:55:37 +0000 (18:55 -0700)]
Merge tag 'nfs-for-5.18-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Features:
- Switch NFS to use readahead instead of the obsolete readpages.
- Readdir fixes to improve cacheability of large directories when
there are multiple readers and writers.
- Readdir performance improvements when doing a seekdir() immediately
after opening the directory (common when re-exporting NFS).
- NFS swap improvements from Neil Brown.
- Loosen up memory allocation to permit direct reclaim and write back
in cases where there is no danger of deadlocking the writeback code
or NFS swap.
- Avoid sillyrename when the NFSv4 server claims to support the
necessary features to recover the unlinked but open file after
reboot.
Bugfixes:
- Patch from Olga to add a mount option to control NFSv4.1 session
trunking discovery, and default it to being off.
- Fix a lockup in nfs_do_recoalesce().
- Two fixes for list iterator variables being used when pointing to
the list head.
- Fix a kernel memory scribble when reading from a non-socket
transport in /sys/kernel/sunrpc.
- Fix a race where reconnecting to a server could leave the TCP
socket stuck forever in the connecting state.
- Patch from Neil to fix a shutdown race which can leave the SUNRPC
transport timer primed after we free the struct xprt itself.
- Patch from Xin Xiong to fix reference count leaks in the NFSv4.2
copy offload.
- Sunrpc patch from Olga to avoid resending a task on an offlined
transport.
Cleanups:
- Patches from Dave Wysochanski to clean up the fscache code"
* tag 'nfs-for-5.18-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (91 commits)
NFSv4/pNFS: Fix another issue with a list iterator pointing to the head
NFS: Don't loop forever in nfs_do_recoalesce()
SUNRPC: Don't return error values in sysfs read of closed files
SUNRPC: Do not dereference non-socket transports in sysfs
NFSv4.1: don't retry BIND_CONN_TO_SESSION on session error
SUNRPC don't resend a task on an offlined transport
NFS: replace usage of found with dedicated list iterator variable
SUNRPC: avoid race between mod_timer() and del_timer_sync()
pNFS/files: Ensure pNFS allocation modes are consistent with nfsiod
pNFS/flexfiles: Ensure pNFS allocation modes are consistent with nfsiod
NFSv4/pnfs: Ensure pNFS allocation modes are consistent with nfsiod
NFS: Avoid writeback threads getting stuck in mempool_alloc()
NFS: nfsiod should not block forever in mempool_alloc()
SUNRPC: Make the rpciod and xprtiod slab allocation modes consistent
SUNRPC: Fix unx_lookup_cred() allocation
NFS: Fix memory allocation in rpc_alloc_task()
NFS: Fix memory allocation in rpc_malloc()
SUNRPC: Improve accuracy of socket ENOBUFS determination
SUNRPC: Replace internal use of SOCKWQ_ASYNC_NOSPACE
SUNRPC: Fix socket waits for write buffer space
...
Dan Carpenter [Thu, 24 Mar 2022 05:52:07 +0000 (08:52 +0300)]
lib/test: use after free in register_test_dev_kmod()
The "test_dev" pointer is freed but then returned to the caller.
Fixes: dfa79abb0601 ("kmod: add test driver to stress test the module loader") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Linus Torvalds [Tue, 29 Mar 2022 22:06:39 +0000 (15:06 -0700)]
fs: fd tables have to be multiples of BITS_PER_LONG
This has always been the rule: fdtables have several bitmaps in them,
and as a result they have to be sized properly for bitmaps. We walk
those bitmaps in chunks of 'unsigned long' in serveral cases, but even
when we don't, we use the regular kernel bitops that are defined to work
on arrays of 'unsigned long', not on some byte array.
Now, the distinction between arrays of bytes and 'unsigned long'
normally only really ends up being noticeable on big-endian systems, but
Fedor Pchelkin and Alexey Khoroshilov reported that copy_fd_bitmaps()
could be called with an argument that wasn't even a multiple of
BITS_PER_BYTE. And then it fails to do the proper copy even on
little-endian machines.
The bug wasn't in copy_fd_bitmap(), but in sane_fdtable_size(), which
didn't actually sanitize the fdtable size sufficiently, and never made
sure it had the proper BITS_PER_LONG alignment.
That's partly because the alignment historically came not from having to
explicitly align things, but simply from previous fdtable sizes, and
from count_open_files(), which counts the file descriptors by walking
them one 'unsigned long' word at a time and thus naturally ends up doing
sizing in the proper 'chunks of unsigned long'.
But with the introduction of close_range(), we now have an external
source of "this is how many files we want to have", and so
sane_fdtable_size() needs to do a better job.
This also adds that explicit alignment to alloc_fdtable(), although
there it is mainly just for documentation at a source code level. The
arithmetic we do there to pick a reasonable fdtable size already aligns
the result sufficiently.
In fact,clang notices that the added ALIGN() in that function doesn't
actually do anything, and does not generate any extra code for it.
It turns out that gcc ends up confusing itself by combining a previous
constant-sized shift operation with the variable-sized shift operations
in roundup_pow_of_two(). And probably due to that doesn't notice that
the ALIGN() is a no-op. But that's a (tiny) gcc misfeature that doesn't
matter. Having the explicit alignment makes sense, and would actually
matter on a 128-bit architecture if we ever go there.
This also adds big comments above both functions about how fdtable sizes
have to have that BITS_PER_LONG alignment.
1) The flags variable is not initialized. Always use raw_spin_lock_irqsave
and raw_spin_unlock_irqrestore to serialize patching.
2) flush_kernel_vmap_range is primarily intended for DMA flushes. Since
__patch_text_multiple is often called with interrupts disabled, it is
better to directly call flush_kernel_dcache_range_asm and
flush_kernel_icache_range_asm. This avoids an extra call.
3) The final call to flush_icache_range is unnecessary.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de>
Helge Deller [Sun, 27 Mar 2022 13:03:53 +0000 (15:03 +0200)]
parisc: Find a new timesync master if current CPU is removed
When CPU hotplugging is enabled, the user may want to remove the
current CPU which is providing the timer ticks. If this happens
we need to find a new timesync master.
Helge Deller [Fri, 25 Mar 2022 13:22:57 +0000 (14:22 +0100)]
parisc: Move common_stext into .text section when CONFIG_HOTPLUG_CPU=y
Move the common_stext function into the non-init text section if hotplug
is enabled. This function is called from the firmware when hotplugged
CPUs are brought up.
Helge Deller [Fri, 25 Mar 2022 13:31:08 +0000 (14:31 +0100)]
parisc: Implement __cpu_die() and __cpu_disable() for CPU hotplugging
Add relevant code to __cpu_die() and __cpu_disable() to finally enable
the CPU hotplugging features. Reset the irq count values in smp_callin()
to zero before bringing up the CPU.
It seems that the firmware may need up to 8 seconds to fully stop a CPU
in which no other PDC calls are allowed to be made. Use a timeout
__cpu_die() to accommodate for this.
Use "chcpu -d 1" to bring CPU1 down, and "chcpu -e 1" to bring it up.
Helge Deller [Tue, 29 Mar 2022 12:15:29 +0000 (14:15 +0200)]
parisc: Add PDC locking functions for rendezvous code
Add pdc_cpu_rendezvous_lock() and pdc_cpu_rendezvous_unlock()
to lock PDC while CPU is transitioning into rendezvous state.
This is needed, because the transition phase may take up to 8 seconds.
Add pdc_pat_get_PDC_entrypoint() to get PDC entry point for current CPU.
Helge Deller [Sun, 27 Mar 2022 13:41:06 +0000 (15:41 +0200)]
parisc: Clean up cpu_check_affinity() and drop cpu_set_affinity_irq()
The cpu_set_affinity_irq() isn't needed. Not the CPU irqs need to
change, but the slave irq chips simply need to be reprogrammed to
a new CPU irq with the txn_* functions.
projects / kernel.git / log