net: dsa: felix: introduce support for Seville VSC9953 switch
This is another switch from Vitesse / Microsemi / Microchip, that has
10 ports (8 external, 2 internal) and is integrated into the Freescale /
NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A,
except that this is a platform device and Felix is a PCI device, and it
doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus
using a phy_device abstraction for it (yes, it will be refactored to use
a raw mdio_device, like other phylink drivers do, but let's keep it like
that for now). But unlike Felix, the MDIO bus and the PCS are not from
the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in
Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it
is actually an instantiation of drivers/net/phy/mdio-mscc-miim.c. But it
would be difficult to reuse that driver (it doesn't even use regmap, and
it's less than 200 lines of code), so we hand-roll here some internal
MDIO bus accessors within seville_vsc9953.c, which serves the purpose of
driving the PCS absolutely fine.
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of
SerDes protocol, so we need to do pre-validation of PHY mode from device
tree and not let phylink change it.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:09 +0000 (19:57 +0300)]
net: dsa: felix: move probing to felix_vsc9959.c
Felix is not actually meant to be a DSA driver only for the switch
inside NXP LS1028A, but an umbrella for all Vitesse / Microsemi /
Microchip switches that are register-compatible with Ocelot and that are
using in DSA mode (with an NPI Ethernet port).
For the dsa_switch_ops exported by the felix driver to be generic enough
to be used by other non-PCI switches, we need to move the PCI-specific
probing to the low-level translation module felix_vsc9959.c. This way,
other switches can have their own probing functions, as platform devices
or otherwise.
This patch also removes the "Felix instance table", which did not stand
the test of time and is unnecessary at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mscc: ocelot: extend watermark encoding function
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:06 +0000 (19:57 +0300)]
net: mscc: ocelot: disable flow control on NPI interface
The Ocelot switches do not support flow control on Ethernet interfaces
where a DSA tag must be added. If pause frames are enabled, they will be
encapsulated in the DSA tag just like regular frames, and the DSA master
will not recognize them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:05 +0000 (19:57 +0300)]
net: mscc: ocelot: split writes to pause frame enable bit and to thresholds
We don't want ocelot_port_set_maxlen to enable pause frame TX, just to
adjust the pause thresholds.
Move the unconditional enabling of pause TX to ocelot_init_port. There
is no good place to put such setting because it shouldn't be
unconditional. But at the moment it is, we're not changing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:04 +0000 (19:57 +0300)]
net: dsa: felix: create a template for the DSA tags on xmit
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:03 +0000 (19:57 +0300)]
net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields
Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.
There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
Felix and Ocelot, which was their hardware-default value, and which
there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
register field at all, and therefore, if we want to have common code
we would be required to not write to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:01 +0000 (19:57 +0300)]
net: mscc: ocelot: convert port registers to regmap
At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced. The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
devlink: Fix use-after-free when destroying health reporters
Dereferencing the reporter after it was destroyed in order to unlock the
reporters lock results in a use-after-free [1].
Fix this by storing a pointer to the lock in a local variable before
destroying the reporter.
[1]
==================================================================
BUG: KASAN: use-after-free in devlink_health_reporter_destroy+0x15c/0x1b0 net/core/devlink.c:5476
Read of size 8 at addr ffff8880650fd020 by task syz-executor.1/904
Memory state around the buggy address: ffff8880650fcf00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8880650fcf80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8880650fd000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8880650fd080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8880650fd100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Fixes: 341b317a6064 ("devlink: Rework devlink health reporter destructor") Fixes: 3168b12f8b46 ("devlink: Add devlink health port reporters API") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLIB is not selected by mdio-mscc-miim but it uses mdio devres helpers.
Explicitly select MDIO_DEVRES in this driver's Kconfig entry.
Reported-by: kernel test robot <lkp@intel.com> Fixes: 78f5e7e3ac9d ("net: phy: add a Kconfig option for mdio_devres") Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/dev.c:5594:1: warning:
symbol '__pcpu_scope_flush_works' was not declared. Should it be static?
'flush_works' is not used outside of dev.c, so marks
it static.
Fixes: 8e0cd7eeff1ac ("net: batch calls to flush_all_backlogs()") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mlxsw: Add support for buffer drops mirroring
This set offloads the recently introduced qevent infrastructure in TC and
allows mlxsw to support mirroring of packets that were dropped due to
buffer related reasons (e.g., early drops) during forwarding.
Up until now mlxsw only supported mirroring that was either triggered by
per-port triggers (i.e., via matchall) or by the policy engine (i.e.,
via flower). Packets that are dropped due to buffer related reasons are
mirrored using a third type of trigger, a global trigger.
Global triggers are bound once to a mirroring (SPAN) agent and enabled
on a per-{port, TC} basis. This allows users, for example, to request
that only packets that were early dropped on a specific netdev to be
mirrored.
Patch set overview:
Patch #1 extends flow_block_offload and indirect offload structure to pass
a scheduler instead of a netdevice. That is necessary, because binding type
and netdevice are not a unique identifier of the block anymore.
Patches #2-#3 add the required registers to support above mentioned
functionality.
Patches #4-#6 gradually add support for global mirroring triggers.
Patch #7 adds support for enablement of global mirroring triggers.
Patches #8-#11 are cleanups in the flow offload code and shuffle some
code around to make the qevent offload easier.
Patch #12 implements offload of RED early_drop qevent.
Patch #13 extends the RED selftest for offloaded datapath to cover
early_drop qevent.
v2:
- Patch #1:
- In struct flow_block_indr, track both sch and dev.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:14 +0000 (00:55 +0300)]
mlxsw: spectrum_qdisc: Offload mirroring on RED qevent early_drop
The RED qevents early_drop and mark can be offloaded under the following
fairly strict conditions:
- At most one filter is configured at the qevent block
- The protocol is "any"
- The classifier is matchall
- The action is trap, sample, or mirror with the same conditions as
with other SPAN offloads
- The hw_counters type is none
In this patchset, implement offload of mirror for early_drop qevent.
The ECN trigger is currently not implemented in the FW and therefore
the mark qevent is not supported.
The qevent notifications look exactly like regular block binding
notifications with a binder type that identifies them as qevents.
Therefore the details of processing this binding are fairly similar
to the matchall offload.
struct flow_block_offload.sch points at the qdisc in question. Use it to
figure out if the qdisc is offloaded at all and what TC it configures.
Bounce bindings on not-offloaded qdiscs.
Individual bindings are kept in a list so that several qevents can share
the same block and all binding points get configured as the configured
filters change.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:13 +0000 (00:55 +0300)]
mlxsw: spectrum_flow: Promote binder-type dispatch to spectrum.c
Two RED qevents have been introduced recently. From the point of view of a
driver, qevents are simply blocks with unusual binder types. However they
need to be handled by different logic than ACL-like flows.
Thus rename mlxsw_sp_setup_tc_block() to mlxsw_sp_setup_tc_block_clsact()
and move the binder-type dispatch from there to spectrum.c into a new
function of the original name. The new dispatcher is easier to extend with
new binder types.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:12 +0000 (00:55 +0300)]
mlxsw: spectrum_matchall: Publish matchall data structures
A following patch introduces offloading of filters attached to blocks bound
to the RED tail_drop qevent. The only classifier that mlxsw will permit in
this role is matchall. mlxsw currently offloads matchall filters used with
clsact qdisc. The data structures used for that offload will come handy for
the qevent offload as well. Publish them in spectrum.h.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_span: Add APIs to enable / disable global mirroring triggers
While the binding of global mirroring triggers to a SPAN agent is
global, packets are only mirrored if they belong to a port and TC on
which the trigger was enabled. This allows, for example, to mirror
packets that were tail-dropped on a specific netdev.
Implement the operations that allow to enable / disable a global
mirroring trigger on a specific port and TC.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_span: Add support for global mirroring triggers
Global mirroring triggers are triggers that are only keyed by their
trigger, as opposed to per-port triggers, which are keyed by their
trigger and port.
Such triggers allow mirroring packets that were tail/early dropped or
ECN marked to a SPAN agent.
Implement the previously added trigger operations for these global
triggers. Since such triggers are only supported from Spectrum-2
onwards, have the Spectrum-1 operations return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_span: Prepare for global mirroring triggers
Currently, a SPAN agent can only be bound to a per-port trigger where
the trigger is either an incoming packet (INGRESS) or an outgoing packet
(EGRESS) to / from the port.
The subsequent patch will introduce the concept of global mirroring
triggers. The binding / unbinding of global triggers is different than
that of per-port triggers. Such triggers also need to be enabled /
disabled on a per-{port, TC} basis and are only supported from
Spectrum-2 onwards.
Add trigger operations that allow us to abstract these differences. Only
implement the operations for per-port triggers. Next patch will
implement the operations for global triggers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_span: Move SPAN operations out of global file
The per-ASIC SPAN operations are relevant to the SPAN module and
therefore should be implemented there and not in the main driver file.
Move them.
These operations will be extended later on.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Fri, 10 Jul 2020 21:55:05 +0000 (00:55 +0300)]
mlxsw: reg: Add Monitoring Port Analyzer Global Register
This register is used for global port analyzer configurations.
Signed-off-by: Amit Cohen <amitc@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used to configure the mirror enable for different
mirror reasons.
Signed-off-by: Amit Cohen <amitc@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 10 Jul 2020 21:55:03 +0000 (00:55 +0300)]
net: sched: Pass qdisc reference in struct flow_block_offload
Previously, shared blocks were only relevant for the pseudo-qdiscs ingress
and clsact. Recently, a qevent facility was introduced, which allows to
bind blocks to well-defined slots of a qdisc instance. RED in particular
got two qevents: early_drop and mark. Drivers that wish to offload these
blocks will be sent the usual notification, and need to know which qdisc it
is related to.
To that end, extend flow_block_offload with a "sch" pointer, and initialize
as appropriate. This prompts changes in the indirect block facility, which
now tracks the scheduler in addition to the netdevice. Update signatures of
several functions similarly.
Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 00:20:40 +0000 (17:20 -0700)]
Merge branch 'net-simple-kerneldoc-fixes'
Andrew Lunn says:
====================
net simple kerneldoc fixes
This is a collection of simple kerneldoc fixes. They are all low
hanging fruit, were not real understanding of the code was needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:14 +0000 (01:15 +0200)]
net: tipc: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Jon Maloy <jmaloy@redhat.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:12 +0000 (01:15 +0200)]
net: socket: Move kerneldoc next to function it documents
Fix the warning "Function parameter or member 'inode' not described in
'__sock_release'' due to the kerneldoc being placed before
__sock_release() not sock_release(), which does not take an inode
parameter.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:11 +0000 (01:15 +0200)]
net: sched: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:07 +0000 (01:15 +0200)]
net: netlabel: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Paul Moore <paul@paul-moore.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:06 +0000 (01:15 +0200)]
net: netfilter: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Pablo Neira Ayuso <pablo@netfilter.org> Cc: Jozsef Kadlecsik <kadlec@netfilter.org> Cc: Florian Westphal <fw@strlen.de> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:03 +0000 (01:15 +0200)]
net: ipv6: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:15:02 +0000 (01:15 +0200)]
net: ipv4: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Paul Moore <paul@paul-moore.com> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:14:58 +0000 (01:14 +0200)]
net: can: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sun, 12 Jul 2020 23:14:57 +0000 (01:14 +0200)]
net: 9p: kerneldoc fixes
Simple fixes which require no deep knowledge of the code.
Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Latchesar Ionkov <lucho@ionkov.net> Cc: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder [Mon, 13 Jul 2020 12:24:18 +0000 (07:24 -0500)]
net: ipa: fix kerneldoc comments
This commit affects comments (and in one case, whitespace) only.
Throughout the IPA code, return statements are documented using
"@Return:", whereas they should use "Return:" instead. Fix these
mistakes.
In function definitions, some parameters are missing their comment
to describe them. And in structure definitions, some fields are
missing their comment to describe them. Add these missing
descriptions.
Some arguments changed name and type along the way, but their
descriptions were not updated (an endpoint pointer is now used in
many places that previously used an endpoint ID). Fix these
incorrect parameter descriptions.
In the description for the ipa_clock structure, one field had a
semicolon instead of a colon in its description. Fix this.
Add a missing function description for ipa_gsi_endpoint_data_empty().
All of these issues were identified when building with "W=1".
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot found that addr_to_string() is available only when
DEBUG is defined. And I found that what that function is doing is
what %pM will do. Thus, replace %s with %pM and remove thread-unsafe
addr_to_string() function.
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: fix undefined br_vlan_can_enter_range in tunnel code
If bridge vlan filtering is not defined we won't have
br_vlan_can_enter_range and thus will get a compile error as was
reported by Stephen and the build bot. So let's define a stub for when
vlan filtering is not used.
Fixes: 2a9984588899 ("net: bridge: notify on vlan tunnel changes done via the old api") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'sky2_alloc_buffers()', GFP_KERNEL can be used
because some other memory allocations in the same function already use this
flag.
When memory is allocated in 'sky2_probe()', GFP_KERNEL can be used
because another memory allocations in the same function already uses this
flag.
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'skge_up()', GFP_KERNEL can be used because
some other memory allocations done a few lines below in 'skge_ring_alloc()'
already use this flag.
====================
Fix MTU warnings for fec/mv886xxx combo
Since changing the MTU of dsa slave interfaces was implemented, the
fec/mv88e6xxx combo has been giving warnings:
[ 2.275925] mv88e6085 0.2:00: nonfatal error -95 setting MTU on port 9
[ 2.284306] eth1: mtu greater than device maximum
[ 2.287759] fec 400d1000.ethernet eth1: error -22 setting MTU to include DSA overhead
This patchset adds support for changing the MTU on mv88e6xxx switches,
which do support jumbo frames. And it modifies the FEC driver to
support its true MTU range, which is larger than the default Ethernet
MTU.
====================
Tested-by: Chris Healy <cphealy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Sat, 11 Jul 2020 20:32:06 +0000 (22:32 +0200)]
net: fec: Set max MTU size to allow the MTU to be changed
The FEC allocates 2K buffers, but looses some of it due to
alignment. It can however support an MTU bigger than the default. This
is particularly interesting when used in combination with Ethernet
switches supporting DSA, which have extra headers. The DSA core will
try to increase the MTU to support these extra headers. If the max
size defaults to that of standard Ethernet we get a warning. By
setting the max to what the driver actually supports, we avoid this
warning.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: notify on vlan tunnel changes done via the old api
If someone uses the old vlan API to configure tunnel mappings we'll only
generate the old-style full port notification. That would be a problem
if we are monitoring the new vlan notifications for changes. The patch
resolves the issue by adding vlan notifications to the old tunnel netlink
code. As usual we try to compress the notifications for as many vlans
in a range as possible, thus a vlan tunnel change is considered able
to enter the "current" vlan notification range if:
1. vlan exists
2. it has actually changed (curr_change == true)
3. it passes all standard vlan notification range checks done by
br_vlan_can_enter_range() such as option equality, id continuity etc
Note that vlan tunnel changes (add/del) are considered a part of vlan
options so only RTM_NEWVLAN notification is generated with the relevant
information inside.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag '5.8-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Four cifs/smb3 fixes: the three for stable fix problems found recently
with change notification including a reference count leak"
* tag '5.8-rc4-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number
cifs: fix reference leak for tlink
smb3: fix unneeded error message on change notify
cifs: remove the retry in cifs_poxis_lock_set
smb3: fix access denied on change notify request to some servers
Merge tag 'inclusive-terminology' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/linux
Pull coding style terminology documentation from Dan Williams:
"The discussion has tapered off as well as the incoming ack, review,
and sign-off tags. I did not see a reason to wait for the next merge
window"
* tag 'inclusive-terminology' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/linux:
CodingStyle: Inclusive Terminology
1) Restore previous behavior of CAP_SYS_ADMIN wrt loading networking
BPF programs, from Maciej Żenczykowski.
2) Fix dropped broadcasts in mac80211 code, from Seevalamuthu
Mariappan.
3) Slay memory leak in nl80211 bss color attribute parsing code, from
Luca Coelho.
4) Get route from skb properly in ip_route_use_hint(), from Miaohe Lin.
5) Don't allow anything other than ARPHRD_ETHER in llc code, from Eric
Dumazet.
6) xsk code dips too deeply into DMA mapping implementation internals.
Add dma_need_sync and use it. From Christoph Hellwig
7) Enforce power-of-2 for BPF ringbuf sizes. From Andrii Nakryiko.
8) Check for disallowed attributes when loading flow dissector BPF
programs. From Lorenz Bauer.
9) Correct packet injection to L3 tunnel devices via AF_PACKET, from
Jason A. Donenfeld.
10) Don't advertise checksum offload on ipa devices that don't support
it. From Alex Elder.
11) Resolve several issues in TCP MD5 signature support. Missing memory
barriers, bogus options emitted when using syncookies, and failure
to allow md5 key changes in established states. All from Eric
Dumazet.
12) Fix interface leak in hsr code, from Taehee Yoo.
13) VF reset fixes in hns3 driver, from Huazhong Tan.
14) Make loopback work again with ipv6 anycast, from David Ahern.
15) Fix TX starvation under high load in fec driver, from Tobias
Waldekranz.
16) MLD2 payload lengths not checked properly in bridge multicast code,
from Linus Lüssing.
17) Packet scheduler code that wants to find the inner protocol
currently only works for one level of VLAN encapsulation. Allow
Q-in-Q situations to work properly here, from Toke
Høiland-Jørgensen.
18) Fix route leak in l2tp, from Xin Long.
19) Resolve conflict between the sk->sk_user_data usage of bpf reuseport
support and various protocols. From Martin KaFai Lau.
20) Fix socket cgroup v2 reference counting in some situations, from
Cong Wang.
21) Cure memory leak in mlx5 connection tracking offload support, from
Eli Britstein.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
mlxsw: pci: Fix use-after-free in case of failed devlink reload
mlxsw: spectrum_router: Remove inappropriate usage of WARN_ON()
net: macb: fix call to pm_runtime in the suspend/resume functions
net: macb: fix macb_suspend() by removing call to netif_carrier_off()
net: macb: fix macb_get/set_wol() when moving to phylink
net: macb: mark device wake capable when "magic-packet" property present
net: macb: fix wakeup test in runtime suspend/resume routines
bnxt_en: fix NULL dereference in case SR-IOV configuration fails
libbpf: Fix libbpf hashmap on (I)LP32 architectures
net/mlx5e: CT: Fix memory leak in cleanup
net/mlx5e: Fix port buffers cell size value
net/mlx5e: Fix 50G per lane indication
net/mlx5e: Fix CPU mapping after function reload to avoid aRFS RX crash
net/mlx5e: Fix VXLAN configuration restore after function reload
net/mlx5e: Fix usage of rcu-protected pointer
net/mxl5e: Verify that rpriv is not NULL
net/mlx5: E-Switch, Fix vlan or qos setting in legacy mode
net/mlx5: Fix eeprom support for SFP module
cgroup: Fix sock_cgroup_data on big-endian.
selftests: bpf: Fix detach from sockmap tests
...
CONFIG_CC_IS_GCC is undefined when Clang is used, which breaks the build
(see our Travis link below).
Clang 8 was chosen as a minimum version for this check because there
were some improvements around __builtin_constant_p in that release. In
reality, MIPS was not even buildable until clang 9 so that check was not
technically necessary. Just remove all compiler checks and just assume
that we have a working compiler.
inet: Remove an unnecessary argument of syn_ack_recalc().
Commit 0daa6efa7b9563f6661bbcc5a28255232535d4f4 ("tcp: reduce SYN-ACK
retrans for TCP_DEFER_ACCEPT") introduces syn_ack_recalc() which decides
if a minisock is held and a SYN+ACK is retransmitted or not.
If rskq_defer_accept is not zero in syn_ack_recalc(), max_retries always
has the same value because max_retries is overwritten by rskq_defer_accept
in reqsk_timer_handler().
This commit adds three changes:
- remove redundant non-zero check for rskq_defer_accept in
reqsk_timer_handler().
- remove max_retries from the arguments of syn_ack_recalc() and use
rskq_defer_accept instead.
- rename thresh to max_syn_ack_retries for readability.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp> Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com> CC: Julian Anastasov <ja@ssi.bg> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: pci: Fix use-after-free in case of failed devlink reload
In case devlink reload failed, it is possible to trigger a
use-after-free when querying the kernel for device info via 'devlink dev
info' [1].
This happens because as part of the reload error path the PCI command
interface is de-initialized and its mailboxes are freed. When the
devlink '->info_get()' callback is invoked the device is queried via the
command interface and the freed mailboxes are accessed.
Fix this by initializing the command interface once during probe and not
during every reload.
This is consistent with the other bus used by mlxsw (i.e., 'mlxsw_i2c')
and also allows user space to query the running firmware version (for
example) from the device after a failed reload.
[1]
BUG: KASAN: use-after-free in memcpy include/linux/string.h:406 [inline]
BUG: KASAN: use-after-free in mlxsw_pci_cmd_exec+0x177/0xa60 drivers/net/ethernet/mellanox/mlxsw/pci.c:1675
Write of size 4096 at addr ffff88810ae32000 by task syz-executor.1/2355
Fixes: eb298403a567 ("mlxsw: core: Add support for devlink info command") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Jul 2020 21:32:02 +0000 (14:32 -0700)]
Merge branch 'devlink-health'
Moshe Shemesh says:
====================
Add devlink-health support for devlink ports
Implement support for devlink health reporters on per-port basis.
This patchset comes to fix a design issue as some health reporters report
on errors and run recovery on device level while the actual functionality
is on port level. As for the current implemented devlink health reporters
it is relevant only to Tx and Rx reporters of mlx5, which has only one
port, so no real effect on functionality, but this should be fixed before
more drivers will use devlink health reporters.
First part in the series prepares common functions parts for health
reporter implementation. Second introduces required API to devlink-health
and mlx5e ones demonstrate its usage and implement the feature for mlx5
driver.
The per-port reporter functionality is achieved by adding a list of
devlink_health_reporters to devlink_port struct in a manner similar to
existing device infrastructure. This is the only major difference and
it makes possible to fully reuse device reporters operations.
The effect will be seen in conjunction with iproute2 additions and
will affect all devlink health commands. User can distinguish between
device and port reporters by looking at a devlink handle. Port reporters
have a port index at the end of the address and such addresses can be
provided as a parameter in every place where devlink-health accepted it.
These can be obtained from devlink port show command.
For example:
$ devlink health show
pci/0000:00:0a.0:
reporter fw
state healthy error 0 recover 0 auto_dump true
pci/0000:00:0a.0/1:
reporter tx
state healthy error 0 recover 0 grace_period 500 auto_recover true auto_dump true
$ devlink health set pci/0000:00:0a.0/1 reporter tx grace_period 1000 \
auto_recover false auto_dump false
$ devlink health show pci/0000:00:0a.0/1 reporter tx
pci/0000:00:0a.0/1:
reporter tx
state healthy error 0 recover 0 grace_period 1000 auto_recover flase auto_dump false
Note: User can use the same devlink health uAPI commands can get now either
port health reporter or device health reporter.
For example, the recover command:
Before this patchset: devlink health recover DEV reporter REPORTER_NAME
After this patchset: devlink health recover { DEV | DEV/PORT_INDEX } reporter REPORTER_NAME
Changes v1 -> v2:
Fixed functions comment to match parameters list.
Changes v2 -> v3:
Added motivation to cover letter and note on uAPI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5e: Move devlink port register and unregister calls
Register devlink ports upon NIC init. TX and RX health reporters handle
errors which may occur early on at driver initialization. And because
these reporters are to be moved to port context, they require devlink
ports to be already registered.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
devlink: Implement devlink health reporters on per-port basis
Add devlink-health reporter support on per-port basis.
The main difference existing devlink-health is that port reporters are
stored in per-devlink_port lists. Upon creation of such health reporter the
reference to a port it belongs to is stored in reporter struct.
Fill the port index attribute in devlink-health response to
allow devlink userspace utility to distinguish between device and port
reporters.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
devlink: Rework devlink health reporter destructor
Devlink keeps its own reference to every reporter in a list and inits
refcount to 1 upon reporter's creation. Existing destructor waits to
free the memory indefinitely using msleep() until all references except
devlink's own are put.
Rework this mechanism by moving memory free routine to a separate
function, which is called when the last reporter reference is put.
Besides, it allows to call __devlink_health_reporter_destroy() while
locked on a reporters list mutex in symmetry to
__devlink_health_reporter_create(), which is required in follow-up
patch.
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Jul 2020 21:29:38 +0000 (14:29 -0700)]
Merge branch 'macb-WOL-fixes'
Nicolas Ferre says:
====================
net: macb: Wake-on-Lan magic packet fixes and GEM handling
Here is a split series to fix WoL magic-packet on the current macb driver. Only
fixes in this one based on current net/master.
Changes in v5:
- Addressed the error code returned by phylink_ethtool_set_wol() as suggested
by Russell.
If PHY handles WoL, MAC doesn't stay in the way.
- Removed Florian's tag on 3/5 because of the above changes.
- Correct the "Fixes" tag on 1/5.
Changes in v4:
- Pure bug fix series for 'net'. GEM addition and MACB update removed: will be
sent later.
Changes in v3:
- Revert some of the v2 changes done in macb_resume(). Now the resume function
supports in-depth re-configuration of the controller in order to deal with
deeper sleep states. Basically as it was before changes introduced by this
series
- Tested for non-regression with our deeper Power Management mode which cuts
power to the controller completely
Changes in v2:
- Add patch 4/7 ("net: macb: fix macb_suspend() by removing call to netif_carrier_off()")
needed for keeping phy state consistent
- Add patch 5/7 ("net: macb: fix call to pm_runtime in the suspend/resume functions") that prevent
putting the macb in runtime pm suspend mode when WoL is used
- Collect review tags on 3 first patches from Florian: Thanks!
- Review of macb_resume() function
- Addition of pm_wakeup_event() in both MACB and GEM WoL IRQ handlers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 10 Jul 2020 12:46:45 +0000 (14:46 +0200)]
net: macb: fix call to pm_runtime in the suspend/resume functions
The calls to pm_runtime_force_suspend/resume() functions are only
relevant if the device is not configured to act as a WoL wakeup source.
Add the device_may_wakeup() test before calling them.
Fixes: 18f5ab9d5ed0 ("net: macb: add wake-on-lan support via magic packet") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Cc: Sergio Prado <sergio.prado@e-labworks.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 10 Jul 2020 12:46:44 +0000 (14:46 +0200)]
net: macb: fix macb_suspend() by removing call to netif_carrier_off()
As we now use the phylink call to phylink_stop() in the non-WoL path,
there is no need for this call to netif_carrier_off() anymore. It can
disturb the underlying phylink FSM.
Fixes: 46e1536937ee ("net: macb: convert to phylink") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Cc: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 10 Jul 2020 12:46:43 +0000 (14:46 +0200)]
net: macb: fix macb_get/set_wol() when moving to phylink
Keep previous function goals and integrate phylink actions to them.
phylink_ethtool_get_wol() is not enough to figure out if Ethernet driver
supports Wake-on-Lan.
Initialization of "supported" and "wolopts" members is done in phylink
function, no need to keep them in calling function.
phylink_ethtool_set_wol() return value is considered and determines
if the MAC has to handle WoL or not. The case where the PHY doesn't
implement WoL leads to the MAC configuring it to provide this feature.
Fixes: 46e1536937ee ("net: macb: convert to phylink") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Cc: Antoine Tenart <antoine.tenart@bootlin.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 10 Jul 2020 12:46:42 +0000 (14:46 +0200)]
net: macb: mark device wake capable when "magic-packet" property present
Change the way the "magic-packet" DT property is handled in the
macb_probe() function, matching DT binding documentation.
Now we mark the device as "wakeup capable" instead of calling the
device_init_wakeup() function that would enable the wakeup source.
For Ethernet WoL, enabling the wakeup_source is done by
using ethtool and associated macb_set_wol() function that
already calls device_set_wakeup_enable() for this purpose.
That would reduce power consumption by cutting more clocks if
"magic-packet" property is set but WoL is not configured by ethtool.
Fixes: 18f5ab9d5ed0 ("net: macb: add wake-on-lan support via magic packet") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Cc: Sergio Prado <sergio.prado@e-labworks.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 10 Jul 2020 12:46:41 +0000 (14:46 +0200)]
net: macb: fix wakeup test in runtime suspend/resume routines
Use the proper struct device pointer to check if the wakeup flag
and wakeup source are positioned.
Use the one passed by function call which is equivalent to
&bp->dev->dev.parent.
It's preventing the trigger of a spurious interrupt in case the
Wake-on-Lan feature is used.
Fixes: 03c922bc9154 ("net: macb: Add pm runtime support") Cc: Claudiu Beznea <claudiu.beznea@microchip.com> Cc: Harini Katakam <harini.katakam@xilinx.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: fix NULL dereference in case SR-IOV configuration fails
we need to set 'active_vfs' back to 0, if something goes wrong during the
allocation of SR-IOV resources: otherwise, further VF configurations will
wrongly assume that bp->pf.vf[x] are valid memory locations, and commands
like the ones in the following sequence:
# echo 2 >/sys/bus/pci/devices/${ADDR}/sriov_numvfs
# ip link set dev ens1f0np0 up
# ip link set dev ens1f0np0 vf 0 trust on
Fixes: dfe047769e715 ("bnxt_en: New Broadcom ethernet driver.") Reported-by: Fei Liu <feliu@redhat.com> CC: Jonathan Toppins <jtoppins@redhat.com> CC: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Acked-by: Jonathan Toppins <jtoppins@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Restore CT state from lookup in zone instead of tupleid
On a miss, Use this zone + 5 tuple taken from the skb, to lookup the CT
entry and restore it, instead of the driver allocated tuple id.
This improves flow insertion rate by avoiding the allocation of a header
rewrite context to maintain the tupleid.
2) Re-use modify header HW objects for identical modify actions.
3) Expand tunnel register mappings
Reg_c1 is 32 bits wide. Before this patchset, 24 bit were allocated
for the tuple_id, 6 bits for tunnel mapping and 2 bits for tunnel
options mappings.
Restoring the ct state from zone lookup instead of tuple id requires
reg_c1 to store 8 bits mapping the ct zone, leaving 24 bits for tunnel
mappings.
Expand tunnel and tunnel options register mappings to 12 bit each.
4) Trivial cleanup and fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 10 Jul 2020 21:02:01 +0000 (14:02 -0700)]
Merge tag 'mlx5-fixes-2020-07-02' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2020-07-02
This series introduces some fixes to mlx5 driver.
V1->v2:
- Drop "ip -s" patch and mirred device hold reference patch.
- Will revise them in a later submission.
Please pull and let me know if there is any problem.
For -stable v5.2
('net/mlx5: Fix eeprom support for SFP module')
For -stable v5.4
('net/mlx5e: Fix 50G per lane indication')
For -stable v5.5
('net/mlx5e: Fix CPU mapping after function reload to avoid aRFS RX crash')
('net/mlx5e: Fix VXLAN configuration restore after function reload')
For -stable v5.7
('net/mlx5e: CT: Fix memory leak in cleanup')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
udp_tunnel: add NIC RX port offload infrastructure
Kernel has a facility to notify drivers about the UDP tunnel ports
so that devices can recognize tunneled packets. This is important
mostly for RX - devices which don't support CHECKSUM_COMPLETE can
report checksums of inner packets, and compute RSS over inner headers.
Some drivers also match the UDP tunnel ports also for TX, although
doing so may lead to false positives and negatives.
Unfortunately the user experience when trying to take adavantage
of these facilities is suboptimal. First of all there is no way
for users to check which ports are offloaded. Many drivers resort
to printing messages to aid debugging, other use debugfs. Even worse
the availability of the RX features (NETIF_F_RX_UDP_TUNNEL_PORT)
is established purely on the basis of the driver having the ndos
installed. For most drivers, however, the ability to perform offloads
is contingent on device capabilities (driver support multiple device
and firmware versions). Unless driver resorts to hackish clearing
of features set incorrectly by the core - users are left guessing
whether their device really supports UDP tunnel port offload or not.
There is currently no way to indicate or configure whether RX
features include just the checksum offload or checksum and using
inner headers for RSS. Many drivers default to not using inner
headers for RSS because most implementations populate the source
port with entropy from the inner headers. This, however, is not
always the case, for example certain switches are only able to
use a fixed source port during encapsulation.
We have also seen many driver authors get the intricacies of UDP
tunnel port offloads wrong. Most commonly the drivers forget to
perform reference counting, or take sleeping locks in the callbacks.
This work tries to improve the situation by pulling the UDP tunnel
port table maintenance out of the drivers. It turns out that almost
all drivers maintain a fixed size table of ports (in most cases one
per tunnel type), so we can take care of all the refcounting in the
core, and let the driver specify if they need to sleep in the
callbacks or not. The new common implementation will also support
replacing ports - when a port is removed from a full table it will
try to find a previously missing port to take its place.
This patch only implements the core functionality along with a few
drivers I was hoping to test manually [1] along with a test based
on a netdevsim implementation. Following patches will convert all
the drivers. Once that's complete we can remove the ndos, and rely
directly on the new infrastrucutre.
Then after RSS (RXFH) is converted to netlink we can add the ability
to configure the use of inner RSS headers for UDP tunnels.
[1] Unfortunately I wasn't able to, turns out 2 of the devices
I had access to were older generation or had old FW, and they
did not actually support UDP tunnel port notifications (see
the second paragraph). The thrid device appears to program
the UDP ports correctly but it generates bad UDP checksums with
or without these patches. Long story short - I'd appreciate
reviews and testing here..
v4:
- better build fix (hopefully this one does it..)
v3:
- fix build issue;
- improve bnxt changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Jul 2020 00:42:52 +0000 (17:42 -0700)]
bnxt: convert to new udp_tunnel_nic infra
Convert to new infra, taking advantage of sleeping in callbacks.
v2:
- use bp->*_fw_dst_port_id != INVALID_HW_RING_ID as indication
that the offload is active.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Jul 2020 00:42:51 +0000 (17:42 -0700)]
ixgbe: convert to new udp_tunnel_nic infra
Make use of new common udp_tunnel_nic infra. ixgbe supports
IPv4 only, and only single VxLAN and Geneve ports (one each).
v2:
- split out the RXCSUM feature handling to separate change;
- declare structs separately;
- use ti.type instead of assuming table 0 is VxLAN;
- move setting netdev->udp_tunnel_nic_info to its own switch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Jul 2020 00:42:50 +0000 (17:42 -0700)]
ixgbe: don't clear UDP tunnel ports when RXCSUM is disabled
It appears the clearing of UDP tunnel ports when RXCSUM
is disabled is unnecessary. Driver will not pay attention
to checksum bits if RXCSUM is not set, so we can let
the hardware parse the packets.
Note that the UDP tunnel port NDO handlers don't pay attention
to the state of RXCSUM, so the ports could had been re-programmed,
anyway.
This cleanup simplifies later conversion patch.
v2:
- break this out of the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Jul 2020 00:42:47 +0000 (17:42 -0700)]
ethtool: add tunnel info interface
Add an interface to report offloaded UDP ports via ethtool netlink.
Now that core takes care of tracking which UDP tunnel ports the NICs
are aware of we can quite easily export this information out to
user space.
The responsibility of writing the netlink dumps is split between
ethtool code and udp_tunnel_nic.c - since udp_tunnel module may
not always be loaded, yet we should always report the capabilities
of the NIC.
$ ethtool --show-tunnels eth0
Tunnel information for eth0:
UDP port table 0:
Size: 4
Types: vxlan
No entries
UDP port table 1:
Size: 4
Types: geneve, vxlan-gpe
Entries (1):
port 1230, vxlan-gpe
v4:
- back to v2, build fix is now directly in udp_tunnel.h
v3:
- don't compile ETHTOOL_MSG_TUNNEL_INFO_GET in if CONFIG_INET
not set.
v2:
- fix string set count,
- reorder enums in the uAPI,
- fix type of ETHTOOL_A_TUNNEL_UDP_TABLE_TYPES to bitset
in docs and comments.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Jul 2020 00:42:46 +0000 (17:42 -0700)]
udp_tunnel: add central NIC RX port offload infrastructure
Cater to devices which:
(a) may want to sleep in the callbacks;
(b) only have IPv4 support;
(c) need all the programming to happen while the netdev is up.
Drivers attach UDP tunnel offload info struct to their netdevs,
where they declare how many UDP ports of various tunnel types
they support. Core takes care of tracking which ports to offload.
Use a fixed-size array since this matches what almost all drivers
do, and avoids a complexity and uncertainty around memory allocations
in an atomic context.
Make sure that tunnel drivers don't try to replay the ports when
new NIC netdev is registered. Automatic replays would mess up
reference counting, and will be removed completely once all drivers
are converted.
v4:
- use a #define NULL to avoid build issues with CONFIG_INET=n.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Fri, 10 Jul 2020 00:42:45 +0000 (17:42 -0700)]
udp_tunnel: re-number the offload tunnel types
Make it possible to use tunnel types as flags more easily.
There doesn't appear to be any user using the type as an
array index, so this should make no difference.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log