Yuri Nudelman [Wed, 22 Jun 2022 09:52:34 +0000 (12:52 +0300)]
habanalabs/gaudi: fix a race condition causing DMAR error
There is a rare race condition in CB completion mechanism, that can
occur under a very high pressure of command submissions.
The preconditions for this to happen are:
1. There should be enough command submissions for the pre-allocated
patched CB pool to run out of commands. At this stage we start
allocating new patched CBs as they arrive.
2. CB size has to be exactly (128*n + 104)B for some n, i.e. 24B below
a cache line end.
The flow:
1. Two command buffers being completed on different streams, at the
same time. Denote those CB1 and CB2.
2. Each command buffer is injected with two messages, 16B each - one
for a HBW update of the completion queue, another to raise
interrupt.
3. Assume CB1 updated the completion queue and raise the interrupt.
4. Assume CB2 updated the completion queue but did not raise the
interrupt yet.
5. The host receives the interrupt. It goes over the completion queue
and sees two completions - CB1 and CB2. Release them both.
6. CB2 performs the last command. The problem is that the last command
is split between 2 cache lines. So to read the last 8B of the last
command, it has to access the host again. Problem is - CB2 is
already released. This causes a DMAR error.
The solution to this problem is simply to make sure the last two
commands in the CB are always in the same cache line, using NOP padding.
ran shalit [Wed, 15 Jun 2022 18:24:38 +0000 (21:24 +0300)]
habanalabs: add critical indication in sram ecc
Multiple SRAM SERR events are treated as critical events,
and host should be notified about it. Thus, adding is_critical
indication as part of SRAM ECC failure packet.
Tal Cohen [Thu, 9 Jun 2022 15:08:31 +0000 (18:08 +0300)]
habanalabs/gaudi: notify user process on device unavailable
When a device error occurs, user process would like to get some
indication on the error by reading some device HW info. If the
device is unavailable, user process can't perform any HW device
reading.
Oded Gabbay [Sat, 18 Jun 2022 18:27:07 +0000 (21:27 +0300)]
habanalabs: remove unused get_dma_desc_list_size
This asic callback function is not called anymore from the common code.
The asic-specific function itself is called but from within the
asic-specific code.
Once FW raised an event following a MME2 QMAN error, the driver should
have gone to the corresponding status registers, trying to gather more
info on the error, yet it was accidentally accessing MME1 QMAN address
space.
Generally, we have x4 MMEs, while 0 & 2 are marked MASTER, and
1 & 3 are marked SLAVE. The former can be addressed, yet addressing
the latter is considered an access violation, and will result in a
hung system, which is what unintentionally happened above.
Note that this cannot happen in a secured system, since these registers
are protected with range registers.
Dani Liberman [Thu, 2 Jun 2022 13:15:03 +0000 (16:15 +0300)]
habanalabs: avoid unnecessary error print
When sending a packet to FW right after it made reset, we will get
packet timeout. Since it is expected behavior, we don't need to
print an error in such case.
Hence, when driver is in hard reset it will avoid from printing error
messages about packet timeout.
Tal Cohen [Thu, 19 May 2022 15:00:55 +0000 (18:00 +0300)]
habanalabs: send an event notification when CS timeout occurs
The Driver needs to inform the User process whenever one of its
CS is timed out. The Driver shall recognize the CS timeout and shall
send an eventfd notification, towards user space, whenever a timeout
is expired on a CS.
Tal Cohen [Wed, 8 Jun 2022 14:34:54 +0000 (17:34 +0300)]
habanalabs/gaudi: send device reset notification
Device reset event, indicates that the device shall be reset -
after a short delay. In such case, the driver sends a notification
towards the User process. This allows the User process
to be able to take several debug actions for system
diagnostic purposes.
Tal Cohen [Wed, 8 Jun 2022 13:02:09 +0000 (16:02 +0300)]
habanalabs/gaudi: invoke device reset from one code block
In order to prepare the driver code for device reset event
notification, change the event handler function flow to call
device reset from one code block.
In addition, the commit fixes an issue that reset was performed
w/o checking the 'hard_reset_on_fw_event' state and w/o setting
the HL_DRV_RESET_DELAY flag.
Tal Cohen [Wed, 11 May 2022 15:02:39 +0000 (18:02 +0300)]
habanalabs/gaudi: collect undefined opcode error info
when an undefined opcode error occurres, the driver collects
the relevant information from the Qman and stores it inside
the hdev data structure. An event fd indication is sent towards the
user space.
Note: another commit shall be followed which will add support to
read the error info by an ioctl.
Tomer Tayar [Sun, 22 May 2022 06:43:54 +0000 (09:43 +0300)]
habanalabs: fix race between hl_get_compute_ctx() and hl_ctx_put()
hl_get_compute_ctx() is used to get the pointer to the compute context
from the hpriv object.
The function is called in code paths that are not necessarily initiated
by user, so it is possible that a context release process will happen in
parallel.
This can lead to a race condition in which hl_get_compute_ctx()
retrieves the context pointer, and just before it increments the context
refcount, the context object is released and a freed memory is accessed.
To avoid this race, add a mutex to protect the context pointer in hpriv.
With this lock, hl_get_compute_ctx() will be able to detect if the
context has been released or is about to be released.
struct hl_ctx_mgr has a mutex for contexts IDR with a similar "ctx_lock"
name, so rename it to just "lock" to avoid a confusion with the new
lock.
Yuri Nudelman [Tue, 24 May 2022 13:29:03 +0000 (16:29 +0300)]
habanalabs: keep a record of completed CS outcomes
Often, the user is not interested in the completion timestamp of all
command submissions.
A common situation is, for example, when the user submits a burst of,
possibly, several thousands of commands, then request the completion
timestamp of only couple of specific key commands from all the burst.
The problem is that currently, the outcome of the early commands may be
lost, due to a large amount of later commands, that the user does not
really care about.
This patch creates a separate store with the outcomes of commands the
user has mark explicitly as interested in. This store does not mix the
marked commands with the unmarked ones, hence the data there will
survive for much longer.
Dan Rapaport [Mon, 30 May 2022 11:11:45 +0000 (14:11 +0300)]
habanalabs: align ioctl uapi structures to 64-bit
The compiler is padding the members of the struct to be aligned to
64-bit. The content of the padded bytes is and not zeroed explicitly,
hence might copy undefined data. We add a padding member to the struct
to get a zeroed 64-bit align struct.
Dafna Hirschfeld [Thu, 19 May 2022 07:54:30 +0000 (10:54 +0300)]
habanalabs: add terminating NULL to attrs arrays
Arrays of struct attribute are expected to be NULL terminated.
This is required by API methods such as device_add_groups.
This fixes a crash when loading the driver for Goya device.
Merge tag 'coresight-next-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux into char-misc-next
Suzuki writes:
CoreSight self-hosted tracing changes for v5.20.
- Fixes LOCKDEP warnings on module unload with configfs
- Conversion of DT bindings to DT schema
- Branch broadcast support for perf cs_etm
- Etm4x driver fixes for build failures with Clang and unrolled loops
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
* tag 'coresight-next-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux:
coresight: etm4x: avoid build failure with unrolled loops
Documentation: coresight: Expand branch broadcast documentation
Documentation: coresight: Link config options to existing documentation
Documentation: coresight: Turn numbered subsections into real subsections
coresight: Add config flag to enable branch broadcast
Documentation: coresight: Escape coresight bindings file wildcard
dt-bindings: arm: Convert CoreSight CPU debug to DT schema
dt-bindings: arm: Convert CoreSight bindings to DT schema
dt-bindings: arm: Rename Coresight filenames to match compatible
coresight: syscfg: Update load and unload operations
coresight: configfs: Fix unload of configurations on module exit
coresight: Clear the connection field properly
Merge tag 'fpga-late-for-5.20-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-next
Xu writes:
Here is the second set of FPGA changes for 5.20-rc1
FPGA Manager core:
- Ivan's change to support image offset and data size setting for
reprograming. A parse_header() callback is introduced for drivers to
specify these info.
- Colin's immediate spelling fix for Ivan's patch.
Microchip:
- Ivan's change to add Microchip MPF FPGA manager driver. And MAINTAINERS
entry added for the driver.
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-next branch).
Merge tag 'mhi-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next
Manivannan writes:
MHI Host
--------
Support for new modems:
- Quectel EM120 FCCL based on SDX24. This product MHI configuration is same
as EM120R-GL modem.
- Foxconn Cinterion MV31-W. This product is same as the existing MV31-W
modem but sold as a separate product as it uses a different firmware
baseline.
- Foxconn T99W175 based on SDX55.
Core changes:
- Moved the IRQ allocation to MHI controller registration phase. Since the
MHI endpoint may be powered up/down several times during runtime, it
makes sense to move the IRQ allocation to registration phase and just
enable/disable IRQs during endpoint power up/down.
MHI endpoint
------------
Core changes:
- Added error check for dev_set_name()
* tag 'mhi-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
bus: mhi: ep: Check dev_set_name() return value
bus: mhi: host: pci_generic: Add another Foxconn T99W175
bus: mhi: host: Move IRQ allocation to controller registration phase
bus: mhi: host: pci_generic: Add Cinterion MV31-W with new baseline
bus: mhi: host: pci_generic: Add support for Quectel EM120 FCCL modem
coresight: etm4x: avoid build failure with unrolled loops
When the following configs are enabled:
* CORESIGHT
* CORESIGHT_SOURCE_ETM4X
* UBSAN
* UBSAN_TRAP
Clang fails assemble the kernel with the error:
<instantiation>:1:7: error: expected constant expression in '.inst' directive
.inst (0xd5200000|((((2) << 19) | ((1) << 16) | (((((((((((0x160 + (i * 4))))) >> 2))) >> 7) & 0x7)) << 12) | ((((((((((0x160 + (i * 4))))) >> 2))) & 0xf)) << 8) | (((((((((((0x160 + (i * 4))))) >> 2))) >> 4) & 0x7)) << 5)))|(.L__reg_num_x8))
^
drivers/hwtracing/coresight/coresight-etm4x-core.c:702:4: note: while in
macro instantiation
etm4x_relaxed_read32(csa, TRCCNTVRn(i));
^
drivers/hwtracing/coresight/coresight-etm4x.h:403:4: note: expanded from
macro 'etm4x_relaxed_read32'
read_etm4x_sysreg_offset((offset), false)))
^
drivers/hwtracing/coresight/coresight-etm4x.h:383:12: note: expanded
from macro 'read_etm4x_sysreg_offset'
__val = read_etm4x_sysreg_const_offset((offset)); \
^
drivers/hwtracing/coresight/coresight-etm4x.h:149:2: note: expanded from
macro 'read_etm4x_sysreg_const_offset'
READ_ETM4x_REG(ETM4x_OFFSET_TO_REG(offset))
^
drivers/hwtracing/coresight/coresight-etm4x.h:144:2: note: expanded from
macro 'READ_ETM4x_REG'
read_sysreg_s(ETM4x_REG_NUM_TO_SYSREG((reg)))
^
arch/arm64/include/asm/sysreg.h:1108:15: note: expanded from macro
'read_sysreg_s'
asm volatile(__mrs_s("%0", r) : "=r" (__val)); \
^
arch/arm64/include/asm/sysreg.h:1074:2: note: expanded from macro '__mrs_s'
" mrs_s " v ", " __stringify(r) "\n" \
^
Consider the definitions of TRCSSCSRn and TRCCNTVRn:
drivers/hwtracing/coresight/coresight-etm4x.h:56
#define TRCCNTVRn(n) (0x160 + (n * 4))
drivers/hwtracing/coresight/coresight-etm4x.h:81
#define TRCSSCSRn(n) (0x2A0 + (n * 4))
Where the macro parameter is expanded to i; a loop induction variable
from etm4_disable_hw.
When any compiler can determine that loops may be unrolled, then the
__builtin_constant_p check in read_etm4x_sysreg_offset() defined in
drivers/hwtracing/coresight/coresight-etm4x.h may evaluate to true. This
can lead to the expression `(0x160 + (i * 4))` being passed to
read_etm4x_sysreg_const_offset. Via the trace above, this is passed
through READ_ETM4x_REG, read_sysreg_s, and finally to __mrs_s where it
is string-ified and used directly in inline asm.
Regardless of which compiler or compiler options determine whether a
loop can or can't be unrolled, which determines whether
__builtin_constant_p evaluates to true when passed an expression using a
loop induction variable, it is NEVER safe to allow the preprocessor to
construct inline asm like:
asm volatile (".inst (0x160 + (i * 4))" : "=r"(__val));
^ expected constant expression
Instead of read_etm4x_sysreg_offset() using __builtin_constant_p(), use
__is_constexpr from include/linux/const.h instead to ensure only
expressions that are valid integer constant expressions get passed
through to read_sysreg_s().
This is not a bug in clang; it's a potentially unsafe use of the macro
arguments in read_etm4x_sysreg_offset dependent on __builtin_constant_p.
This is a collection of three fixes for small annoyances.
Two of these are already pending in other trees, but I really don't want
to release another -rc with these issues pending, so I picked up the
patches for these things directly. We'll end up with duplicate commits
eventually, I prefer that over having these issues pending.
The third one is just me getting rid of another BUG_ON() just because it
was reported and I dislike those things so much.
* merge 'hot-fixes' branch:
ida: don't use BUG_ON() for debugging
drm/aperture: Run fbdev removal before internal helpers
ptrace: fix clearing of JOBCTL_TRACED in ptrace_unfreeze_traced()
This is another old BUG_ON() that just shouldn't exist (see also commit a3a14d4efebf: "signal handling: don't use BUG_ON() for debugging").
In fact, as Matthew Wilcox points out, this condition shouldn't really
even result in a warning, since a negative id allocation result is just
a normal allocation failure:
"I wonder if we should even warn here -- sure, the caller is trying to
free something that wasn't allocated, but we don't warn for
kfree(NULL)"
and goes on to point out how that current error check is only causing
people to unnecessarily do their own index range checking before freeing
it.
This was noted by Itay Iellin, because the bluetooth HCI socket cookie
code does *not* do that range checking, and ends up just freeing the
error case too, triggering the BUG_ON().
The HCI code requires CAP_NET_RAW, and seems to just result in an ugly
splat, but there really is no reason to BUG_ON() here, and we have
generally striven for allocation models where it's always ok to just do
free(alloc());
even if the allocation were to fail for some random reason (usually
obviously that "random" reason being some resource limit).
Fixes: 802d8c8f8237 ("ida: simplified functions for id allocation") Reported-by: Itay Iellin <ieitayie@gmail.com> Suggested-by: Matthew Wilcox <willy@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'staging-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for a reported problem that showed
up in 5.19-rc1 in the wlan-ng driver. It has been in linux-next for a
week with no reported problems"
* tag 'staging-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging/wlan-ng: get the correct struct hfa384x in work callback
Merge tag 'char-misc-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are four small char/misc driver fixes for 5.19-rc6 to resolve
some reported issues. They only affect two drivers:
- rtsx_usb: fix for of-reported DMA warning error, the driver was
handling memory buffers in odd ways, it has now been fixed up to be
much simpler and correct by Shuah.
- at25 eeprom driver bugfix for reported problem
All of these have been in linux-next for a week with no reported
problems"
* tag 'char-misc-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: rtsx_usb: set return value in rsp_buf alloc err path
misc: rtsx_usb: use separate command and response buffers
misc: rtsx_usb: fix use of dma mapped buffer for usb bulk transfer
eeprom: at25: Rework buggy read splitting
Merge tag 'kbuild-fixes-v5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Adjust gen_compile_commands.py to the format change of *.mod files
- Remove unused macro in scripts/Makefile.modinst
* tag 'kbuild-fixes-v5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: remove unused cmd_none in scripts/Makefile.modinst
gen_compile_commands: handle multiple lines per .mod file
Merge tag 'irq_urgent_for_v5.19_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Borislav Petkov:
- Gracefully handle failure to request MMIO resources in the GICv3
driver
- Make a static key static in the Apple AIC driver
- Fix the Xilinx intc driver dependency on OF_ADDRESS
* tag 'irq_urgent_for_v5.19_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/apple-aic: Make symbol 'use_fast_ipi' static
irqchip/xilinx: Add explicit dependency on OF_ADDRESS
irqchip/gicv3: Handle resource request failure consistently
Merge tag 'x86_urgent_for_v5.19_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Prepare for and clear .brk early in order to address XenPV guests
failures where the hypervisor verifies page tables and uninitialized
data in that range leads to bogus failures in those checks
- Add any potential setup_data entries supplied at boot to the identity
pagetable mappings to prevent kexec kernel boot failures. Usually,
this is not a problem for the normal kernel as those mappings are
part of the initially mapped 2M pages but if kexec gets to allocate
the second kernel somewhere else, those setup_data entries need to be
mapped there too.
- Fix objtool not to discard text references from the __tracepoints
section so that ENDBR validation still works
- Correct the setup_data types limit as it is user-visible, before 5.19
releases
* tag 'x86_urgent_for_v5.19_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix the setup data types max limit
x86/ibt, objtool: Don't discard text references from tracepoint section
x86/compressed/64: Add identity mappings for setup_data entries
x86: Fix .brk attribute in linker script
x86: Clear .brk area at early boot
x86/xen: Use clear_bss() for Xen PV guests
* tag 'i2c-for-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cadence: Unregister the clk notifier in error path
i2c: piix4: Fix a memory leak in the EFCH MMIO support
drm/aperture: Run fbdev removal before internal helpers
Always run fbdev removal first to remove simpledrm via sysfb_disable().
This clears the internal state.
The later call to drm_aperture_detach_drivers() then does nothing.
Otherwise, with drm_aperture_detach_drivers() running first, the call to
sysfb_disable() uses inconsistent state.
Example backtrace show below:
BUG: KASAN: use-after-free in device_del+0x79/0x5f0
Read of size 8 at addr ffff888108185050 by task systemd-udevd/311
CPU: 0 PID: 311 Comm: systemd-udevd Tainted: G E 5.19.0-rc2-1-default+ #1689
Hardware name: HP ProLiant DL120 G7, BIOS J01 04/21/2011
Call Trace:
device_del+0x79/0x5f0
platform_device_del.part.0+0x19/0xe0
platform_device_unregister+0x1c/0x30
sysfb_disable+0x2d/0x70
remove_conflicting_framebuffers+0x1c/0xf0
remove_conflicting_pci_framebuffers+0x130/0x1a0
drm_aperture_remove_conflicting_pci_framebuffers+0x86/0xb0
mgag200_pci_probe+0x2d/0x140 [mgag200]
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Fixes: 873eb3b11860 ("fbdev: Disable sysfb device registration when removing conflicting FBs") Cc: Javier Martinez Canillas <javierm@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Helge Deller <deller@gmx.de> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Zhen Lei <thunder.leizhen@huawei.com> Cc: Changcheng Deng <deng.changcheng@zte.com.cn> Reviewed-by: Zack Rusin <zackr@vmware.com> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'powerpc-5.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
- On Power8 bare metal, fix creation of RNG platform devices, which are
needed for the /dev/hwrng driver to probe correctly.
Thanks to Jason A. Donenfeld, and Sachin Sant.
* tag 'powerpc-5.19-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: delay rng platform device creation until later in boot
io_uring: check that we have a file table when allocating update slots
If IORING_FILE_INDEX_ALLOC is set asking for an allocated slot, the
helper doesn't check if we actually have a file table or not. The non
alloc path does do that correctly, and returns -ENXIO if we haven't set
one up.
Do the same for the allocated path, avoiding a NULL pointer dereference
when trying to find a free bit.
Fixes: 3c02192c8665 ("io_uring: let IORING_OP_FILES_UPDATE support choosing fixed file slots") Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge tag 'fscache-fixes-20220708' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull fscache fixes from David Howells:
- Fix a check in fscache_wait_on_volume_collision() in which the
polarity is reversed. It should complain if a volume is still marked
acquisition-pending after 20s, but instead complains if the mark has
been cleared (ie. the condition has cleared).
Also switch an open-coded test of the ACQUIRE_PENDING volume flag to
use the helper function for consistency.
- Not a fix per se, but neaten the code by using a helper to check for
the DROPPED state.
- Fix cachefiles's support for erofs to only flush requests associated
with a released control file, not all requests.
- Fix a race between one process invalidating an object in the cache
and another process trying to look it up.
* tag 'fscache-fixes-20220708' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
fscache: Fix invalidation/lookup race
cachefiles: narrow the scope of flushed requests when releasing fd
fscache: Introduce fscache_cookie_is_dropped()
fscache: Fix if condition in fscache_wait_on_volume_collision()
Merge tag 'acpi-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix two recent regressions related to CPPC support.
Specifics:
- Prevent _CPC from being used if the platform firmware does not
confirm CPPC v2 support via _OSC (Mario Limonciello)
- Allow systems with X86_FEATURE_CPPC set to use _CPC even if CPPC
support cannot be agreed on via _OSC (Mario Limonciello)"
* tag 'acpi-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Don't require _OSC if X86_FEATURE_CPPC is supported
ACPI: CPPC: Only probe for _CPC if CPPC v2 is acked
Merge tag 'pm-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a NULL pointer dereference in a devfreq driver and a runtime
PM framework issue that may cause a supplier device to be suspended
before its consumer.
Specifics:
- Fix NULL pointer dereference related to printing a diagnostic
message in the exynos-bus devfreq driver (Christian Marangi)
- Fix race condition in the runtime PM framework which in some cases
may cause a supplier device to be suspended when its consumer is
still active (Rafael Wysocki)"
* tag 'pm-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: exynos-bus: Fix NULL pointer dereference
PM: runtime: Fix supplier device management during consumer probe
PM: runtime: Redefine pm_runtime_release_supplier()
* tag 'cxl-fixes-for-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/mbox: Fix missing variable payload checks in cmd size validation
memregion: Fix memregion_free() fallback definition
cxl/mbox: Use __le32 in get,set_lsa mailbox structures
cxl/core: Use is_endpoint_decoder
cxl: Fix cleanup of port devices on failure to probe driver.
MAINTAINERS: Update Ben's email address
Merge tag 'block-5.19-2022-07-08' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"NVMe pull request with another id quirk addition, and a tracing fix"
* tag 'block-5.19-2022-07-08' of git://git.kernel.dk/linux-block:
nvme: use struct group for generic command dwords
nvme-pci: phison e16 has bogus namespace ids
Merge tag 'io_uring-5.19-2022-07-08' of git://git.kernel.dk/linux-block
Pull io_uring tweak from Jens Axboe:
"Just a minor tweak to an addition made in this release cycle: padding
a 32-bit value that's in a 64-bit union to avoid any potential
funkiness from that"
* tag 'io_uring-5.19-2022-07-08' of git://git.kernel.dk/linux-block:
io_uring: explicit sqe padding for ioctl commands
Merge tag 'for-5.19/fbdev-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes from Helge Deller:
- fbcon now prevents switching to screen resolutions which are smaller
than the font size, and prevents enabling a font which is bigger than
the current screen resolution. This fixes vmalloc-out-of-bounds
accesses found by KASAN.
- Guiling Deng fixed a bug where the centered fbdev logo wasn't
displayed correctly if the screen size matched the logo size.
- Hsin-Yi Wang provided a patch to include errno.h to fix build when
CONFIG_OF isn't enabled.
* tag 'for-5.19/fbdev-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbcon: Use fbcon_info_from_console() in fbcon_modechange_possible()
fbmem: Check virtual screen sizes in fb_set_var()
fbcon: Prevent that screen size is smaller than font size
fbcon: Disallow setting font bigger than screen size
video: of_display_timing.h: include errno.h
fbdev: fbmem: Fix logo center image dx issue
nvmem: mtk-efuse: Simplify with devm_platform_get_and_ioremap_resource()
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
MAINTAINERS: rectify file pattern in MICROCHIP OTPC DRIVER
Commit 6b291610dd57 ("nvmem: microchip-otpc: add support") adds the
Microchip otpc driver and a corresponding MAINTAINERS section, but slips
in a slightly wrong file pattern.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.
Rectify this file pattern in MICROCHIP OTPC DRIVER.
Add support for Microchip OTP controller available on SAMA7G5. The OTPC
controls the access to a non-volatile memory. The memory behind OTPC is
organized into packets, packets are composed by a fixed length header
(4 bytes long) and a variable length payload (payload length is available
in the header). When software request the data at an offset in memory
the OTPC will return (via header + data registers) the whole packet that
has a word at that offset. For the OTP memory layout like below:
if user requests data at address 0x16 the data started at 0x0E will be
returned by controller. User will be able to fetch the whole packet
starting at 0x0E (or parts of the packet) via proper registers. The same
packet will be returned if software request the data at offset 0x0E or
0x12 or 0x1A.
The OTP will be populated by Microchip with at least 2 packets first one
being boot configuration packet and the 2nd one being temperature
calibration packet. The packet order will be preserved b/w different chip
revisions but the packet sizes may change.
For the above reasons and to keep the same software able to work on all
chip variants the read function of the driver is working with a packet
id instead of an offset in OTP memory.
Carlos Llamas [Fri, 1 Jul 2022 18:20:41 +0000 (18:20 +0000)]
binder: fix redefinition of seq_file attributes
The patchset in [1] exported some definitions to binder_internal.h in
order to make the debugfs entries such as 'stats' and 'transaction_log'
available in a binderfs instance. However, the DEFINE_SHOW_ATTRIBUTE
macro expands into a static function/variable pair, which in turn get
redefined each time a source file includes this internal header.
This problem was made evident after a report from the kernel test robot
<lkp@intel.com> where several W=1 build warnings are seen in downstream
kernels. See the following example:
include/../drivers/android/binder_internal.h:111:23: warning: 'binder_stats_fops' defined but not used [-Wunused-const-variable=]
111 | DEFINE_SHOW_ATTRIBUTE(binder_stats);
| ^~~~~~~~~~~~
include/linux/seq_file.h:174:37: note: in definition of macro 'DEFINE_SHOW_ATTRIBUTE'
174 | static const struct file_operations __name ## _fops = { \
| ^~~~~~
This patch fixes the above issues by moving back the definitions into
binder.c and instead creates an array of the debugfs entries which is
more convenient to share with binderfs and iterate through.
Fixes: 3ec9f42aaa61 ("binder: Add stats, state and transactions files") Fixes: a117e63659e6 ("binder: Make transaction_log available in binderfs") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20220701182041.2134313-1-cmllamas@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
see warnings:
| drivers/misc/eeprom/idt_89hpesx.c:570:5: error: format specifies type
| 'unsigned char' but the argument has type 'u16' (aka 'unsigned short')
| [-Werror,-Wformat] memaddr);
-
| drivers/misc/eeprom/idt_89hpesx.c:579:5: error: format specifies type
| 'unsigned char' but the argument has type 'u16' (aka 'unsigned short')
| [-Werror,-Wformat] memaddr);
-
| drivers/misc/eeprom/idt_89hpesx.c:814:4: error: format specifies type
| 'unsigned short' but the argument has type 'unsigned int'
| [-Werror,-Wformat] CSR_REAL_ADDR(csraddr));
There's an ongoing movement to eventually enable the -Wformat flag for
clang. See: https://github.com/ClangBuiltLinux/linux/issues/378
The format specifier for idt_89hpesx.c:570 and 579 was `0x%02hhx`. The
part we care about `%hhx` describes a single byte format, wherein the
leftmost byte of our u16 type (of which memaddr is) is truncated.
example:
```
uint16_t x = 0xbabe;
printf("%hhx\n", x);
// output is: be
// we lost 'ba'
```
There exists a similar issue at idt_89hpesx.c:814 which involves the
CSR_REAL_ADDR macro. This macro returns a u16 but due to default
argument promotion for variadic functions (printf-like) actually
provides an int to the dev_err method.
My proposed solution is to expand the width of the format specifier to
fully encompass the provided argument (which is promoted to an int, see
below). I opted for '%x' as this specifies an unsigned hexadecimal
integer which, with a guarantee, can represent all the values of a u16.
As per C11 6.3.1.1:
(https://www.open-std.org/jtc1/sc22/wg14/www/docs/n1548.pdf)
`If an int can represent all values of the original type ..., the
value is converted to an int; otherwise, it is converted to an
unsigned int. These are called the integer promotions.`
After commit 240442c7424b ("dma-mapping: remove CONFIG_DMA_REMAP") there's
a chance of DMA buffer getting allocated via vmalloc(), which messes up
the mmapping code:
Merge tag 'nvme-5.19-2022-07-07' of git://git.infradead.org/nvme into block-5.19
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.19
- another bogus identifier quirk (Keith Busch)
- use struct group in the tracer to avoid a gcc warning (Keith Busch)"
* tag 'nvme-5.19-2022-07-07' of git://git.infradead.org/nvme:
nvme: use struct group for generic command dwords
nvme-pci: phison e16 has bogus namespace ids
Pavel Begunkov [Thu, 7 Jul 2022 14:00:38 +0000 (15:00 +0100)]
io_uring: explicit sqe padding for ioctl commands
32 bit sqe->cmd_op is an union with 64 bit values. It's always a good
idea to do padding explicitly. Also zero check it in prep, so it can be
used in the future if needed without compatibility concerns.
Merge tag 'devfreq-fixes-for-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux
Pull a devfreq fix for 5.19-rc6 from Chanwoo Choi:
"- Fix exynos-bus NULL pointer dereference by correctly using the local
generated freq_table to output the debug values instead of using the
profile freq_table that is not used in the driver."
* tag 'devfreq-fixes-for-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: exynos-bus: Fix NULL pointer dereference
Fix exynos-bus NULL pointer dereference by correctly using the local
generated freq_table to output the debug values instead of using the
profile freq_table that is not used in the driver.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 520b39385eb4 ("PM / devfreq: Rework freq_table to be local to devfreq struct") Cc: stable@vger.kernel.org Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Acked-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Merge tag 'loongarch-fixes-5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"A fix for tinyconfig build error, a fix for section mismatch warning,
and two cleanups of obsolete code"
* tag 'loongarch-fixes-5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: Fix section mismatch warning
LoongArch: Fix build errors for tinyconfig
LoongArch: Remove obsolete mentions of vcsr
LoongArch: Drop these obsolete selects in Kconfig
- eth: ibmvnic: properly dispose of all skbs during a failover
Previous releases - always broken:
- bpf:
- fix insufficient bounds propagation from
adjust_scalar_min_max_vals
- clear page contiguity bit when unmapping pool
- netfilter: nft_set_pipapo: release elements in clone from
abort path
- mptcp: netlink: issue MP_PRIO signals from userspace PMs
- can:
- rcar_canfd: fix data transmission failed on R-Car V3U
- gs_usb: gs_usb_open/close(): fix memory leak
Misc:
- add Wenjia as SMC maintainer"
* tag 'net-5.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (57 commits)
wireguard: Kconfig: select CRYPTO_CHACHA_S390
crypto: s390 - do not depend on CRYPTO_HW for SIMD implementations
wireguard: selftests: use microvm on x86
wireguard: selftests: always call kernel makefile
wireguard: selftests: use virt machine on m68k
wireguard: selftests: set fake real time in init
r8169: fix accessing unset transport header
net: rose: fix UAF bug caused by rose_t0timer_expiry
usbnet: fix memory leak in error case
Revert "tls: rx: move counting TlsDecryptErrors for sync"
mptcp: update MIB_RMSUBFLOW in cmd_sf_destroy
mptcp: fix local endpoint accounting
selftests: mptcp: userspace PM support for MP_PRIO signals
mptcp: netlink: issue MP_PRIO signals from userspace PMs
mptcp: Acquire the subflow socket lock before modifying MP_PRIO flags
mptcp: Avoid acquiring PM lock for subflow priority changes
mptcp: fix locking in mptcp_nl_cmd_sf_destroy()
net/mlx5e: Fix matchall police parameters validation
net/sched: act_police: allow 'continue' action offload
net: lan966x: hardcode the number of external ports
...
Merge tag 'pinctrl-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Tag Intel pin control as supported in MAINTAINERS
- Fix a NULL pointer exception in the Aspeed driver
- Correct some NAND functions in the Sunxi A83T driver
- Use the right offset for some Sunxi pins
- Fix a zero base offset in the Freescale (NXP) i.MX93
- Fix the IRQ support in the STM32 driver
* tag 'pinctrl-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: stm32: fix optional IRQ support to gpios
pinctrl: imx: Add the zero base flag for imx93
pinctrl: sunxi: sunxi_pconf_set: use correct offset
pinctrl: sunxi: a83t: Fix NAND function name for some pins
pinctrl: aspeed: Fix potential NULL dereference in aspeed_pinmux_set_mux()
MAINTAINERS: Update Intel pin control to Supported
These are indeed "should not happen" situations, but it turns out recent
changes made the 'task_is_stopped_or_trace()' case trigger (fix for that
exists, is pending more testing), and the BUG_ON() makes it
unnecessarily hard to actually debug for no good reason.
It's been that way for a long time, but let's make it clear: BUG_ON() is
not good for debugging, and should never be used in situations where you
could just say "this shouldn't happen, but we can continue".
Use WARN_ON_ONCE() instead to make sure it gets logged, and then just
continue running. Instead of making the system basically unusuable
because you crashed the machine while potentially holding some very core
locks (eg this function is commonly called while holding 'tasklist_lock'
for writing).
Kent Gibson [Wed, 6 Jul 2022 08:45:07 +0000 (16:45 +0800)]
gpiolib: cdev: fix null pointer dereference in linereq_free()
Fix a kernel NULL pointer dereference reported by gpio kselftests.
linereq_free() can be called as part of the cleanup of a failed request,
at which time the desc for a line may not have been determined, so it
is unsafe to dereference without a check.
Tiezhu Yang [Mon, 27 Jun 2022 06:57:35 +0000 (14:57 +0800)]
LoongArch: Fix section mismatch warning
init_numa_memory() is annotated __init and not used by any module,
thus don't export it.
Remove not needed EXPORT_SYMBOL for init_numa_memory() to fix the
following section mismatch warning:
MODPOST vmlinux.symvers
WARNING: modpost: vmlinux.o(___ksymtab+init_numa_memory+0x0): Section mismatch in reference
from the variable __ksymtab_init_numa_memory to the function .init.text:init_numa_memory()
The symbol init_numa_memory is exported and annotated __init
Fix this by removing the __init annotation of init_numa_memory or drop the export.
Qi Hu [Wed, 6 Jul 2022 11:29:37 +0000 (19:29 +0800)]
LoongArch: Remove obsolete mentions of vcsr
The `vcsr` only exists in the old hardware design, it isn't used in any
shipped hardware from Loongson-3A5000 on. Both scalar FP and LSX/LASX
instructions use the `fcsr` as their control and status registers now.
For example, the RM control bit in fcsr0 is shared by FP, LSX and LASX
instructions.
Particularly, fcsr16 to fcsr31 are reserved for LSX/LASX now, access to
these registers has no visible effect if LSX/LASX is enabled, and will
cause SXD/ASXD exceptions if LSX/LASX is not enabled.
So, mentions of vcsr are obsolete in the first place (it was just used
for debugging), let's remove them.
Reviewed-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Qi Hu <huqi@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Commit 740b41dc45ee ("LoongArch: Add build infrastructure") adds the new
file arch/loongarch/Kconfig.
As the work on LoongArch was probably quite some time under development,
various config symbols have changed and disappeared from the time of
initial writing of the Kconfig file and its inclusion in the repository.
Helge Deller [Sat, 25 Jun 2022 11:00:34 +0000 (13:00 +0200)]
fbcon: Use fbcon_info_from_console() in fbcon_modechange_possible()
Use the fbcon_info_from_console() wrapper which was added to kernel
v5.19 with commit 40964d68ad69 ("fbcon: Introduce wrapper for console->fb_info lookup").
Helge Deller [Wed, 29 Jun 2022 13:53:55 +0000 (15:53 +0200)]
fbmem: Check virtual screen sizes in fb_set_var()
Verify that the fbdev or drm driver correctly adjusted the virtual
screen sizes. On failure report the failing driver and reject the screen
size change.
projects / kernel.git / log