If snd_ctl_add() fails in aureon_add_controls(), it immediately returns
and leaves ice->gpio_mutex locked. ice->gpio_mutex locks in
snd_ice1712_save_gpio_status and unlocks in
snd_ice1712_restore_gpio_status(ice).
It seems that the mutex is required only for aureon_cs8415_get(),
so snd_ice1712_restore_gpio_status(ice) can be placed
just after that. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The sanity check for an already mapped virq is done outside of the
irq_domain_mutex-protected section which means that an (unlikely) racing
association may not be detected.
Fix this by factoring out the association implementation, which will
also be used in a follow-on change to fix a shared-interrupt mapping
race.
Commit 341c2feee9ad9 ("take calculation of final prot in
security_mmap_file() into a helper") moved the code to update prot, to be
the actual protections applied to the kernel, to a new helper called
mmap_prot().
However, while without the helper ima_file_mmap() was getting the updated
prot, with the helper ima_file_mmap() gets the original prot, which
contains the protections requested by the application.
A possible consequence of this change is that, if an application calls
mmap() with only PROT_READ, and the kernel applies PROT_EXEC in addition,
that application would have access to executable memory without having this
event recorded in the IMA measurement list. This situation would occur for
example if the application, before mmap(), calls the personality() system
call with READ_IMPLIES_EXEC as the first argument.
Align ima_file_mmap() parameters with those of the mmap_file LSM hook, so
that IMA can receive both the requested prot and the final prot. Since the
requested protections are stored in a new variable, and the final
protections are stored in the existing variable, this effectively restores
the original behavior of the MMAP_CHECK hook.
Cc: stable@vger.kernel.org Fixes: 341c2feee9ad ("take calculation of final prot in security_mmap_file() into a helper") Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com> Reviewed-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When plain IBRS is enabled (not enhanced IBRS), the logic in
spectre_v2_user_select_mitigation() determines that STIBP is not needed.
The IBRS bit implicitly protects against cross-thread branch target
injection. However, with legacy IBRS, the IBRS bit is cleared on
returning to userspace for performance reasons which leaves userspace
threads vulnerable to cross-thread branch target injection against which
STIBP protects.
Exclude IBRS from the spectre_v2_in_ibrs_mode() check to allow for
enabling STIBP (through seccomp/prctl() by default or always-on, if
selected by spectre_v2_user kernel cmdline parameter).
The AMD side of the loader has always claimed to support mixed
steppings. But somewhere along the way, it broke that by assuming that
the cached patch blob is a single one instead of it being one per
*node*.
So turn it into a per-node one so that each node can stash the blob
relevant for it.
[ NB: Fixes tag is not really the exactly correct one but it is good
enough. ]
Fixes: 10142e5e821f ("x86/microcode: Merge the early microcode loader") Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Cc: <stable@kernel.org> # 2355370cd941 ("x86/microcode/amd: Remove load_microcode_amd()'s bsp parameter") Cc: <stable@kernel.org> # a5ad92134bd1 ("x86/microcode/AMD: Add a @cpu parameter to the reloading functions") Link: https://lore.kernel.org/r/20230130161709.11615-4-bp@alien8.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When arch_prepare_optimized_kprobe calculating jump destination address,
it copies original instructions from jmp-optimized kprobe (see
__recover_optprobed_insn), and calculated based on length of original
instruction.
arch_check_optimized_kprobe does not check KPROBE_FLAG_OPTIMATED when
checking whether jmp-optimized kprobe exists.
As a result, setup_detour_execution may jump to a range that has been
overwritten by jump destination address, resulting in an inval opcode error.
For example, assume that register two kprobes whose addresses are
<func+9> and <func+11> in "func" function.
The original code of "func" function is as follows:
2. Register the kprobe for <func+9>, assume that is kp2, corresponding optimized_kprobe is op2.
register_kprobe(kp2)
register_aggr_kprobe
alloc_aggr_kprobe
__prepare_optimized_kprobe
arch_prepare_optimized_kprobe
__recover_optprobed_insn // copy original bytes from kp1->optinsn.copied_insn,
// jump address = <func+14>
3. disable kp1:
disable_kprobe(kp1)
__disable_kprobe
...
if (p == orig_p || aggr_kprobe_disabled(orig_p)) {
ret = disarm_kprobe(orig_p, true) // add op1 in unoptimizing_list, not unoptimized
orig_p->flags |= KPROBE_FLAG_DISABLED; // op1->flags == KPROBE_FLAG_OPTIMATED | KPROBE_FLAG_DISABLED
...
4. unregister kp2
__unregister_kprobe_top
...
if (!kprobe_disabled(ap) && !kprobes_all_disarmed) {
optimize_kprobe(op)
...
if (arch_check_optimized_kprobe(op) < 0) // because op1 has KPROBE_FLAG_DISABLED, here not return
return;
p->kp.flags |= KPROBE_FLAG_OPTIMIZED; // now op2 has KPROBE_FLAG_OPTIMIZED
}
commit 2d3ebe27fef7 ("kprobes: Set unoptimized flag after unoptimizing code")
modified the update timing of the KPROBE_FLAG_OPTIMIZED, a optimized_kprobe
may be in the optimizing or unoptimizing state when op.kp->flags
has KPROBE_FLAG_OPTIMIZED and op->list is not empty.
The __recover_optprobed_insn check logic is incorrect, a kprobe in the
unoptimizing state may be incorrectly determined as unoptimizing.
As a result, incorrect instructions are copied.
The optprobe_queued_unopt function needs to be exported for invoking in
arch directory.
Link: https://lore.kernel.org/all/20230216034247.32348-2-yangjihong1@huawei.com/ Fixes: 2d3ebe27fef7 ("kprobes: Set unoptimized flag after unoptimizing code") Cc: stable@vger.kernel.org Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable SVM and more importantly force GIF=1 when halting a CPU or
rebooting the machine. Similar to VMX, SVM allows software to block
INITs via CLGI, and thus can be problematic for a crash/reboot. The
window for failure is smaller with SVM as INIT is only blocked while
GIF=0, i.e. between CLGI and STGI, but the window does exist.
Fixes: 2b5df4a9b263 ("x86/reboot: Turn off KVM when halting a CPU") Cc: stable@vger.kernel.org Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20221130233650.1404148-5-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable SVM on all CPUs via NMI shootdown during an emergency reboot.
Like VMX, SVM can block INIT, e.g. if the emergency reboot is triggered
between CLGI and STGI, and thus can prevent bringing up other CPUs via
INIT-SIPI-SIPI.
Disable virtualization in crash_nmi_callback() and rework the
emergency_vmx_disable_all() path to do an NMI shootdown if and only if a
shootdown has not already occurred. NMI crash shootdown fundamentally
can't support multiple invocations as responding CPUs are deliberately
put into halt state without unblocking NMIs. But, the emergency reboot
path doesn't have any work of its own, it simply cares about disabling
virtualization, i.e. so long as a shootdown occurred, emergency reboot
doesn't care who initiated the shootdown, or when.
If "crash_kexec_post_notifiers" is specified on the kernel command line,
panic() will invoke crash_smp_send_stop() and result in a second call to
nmi_shootdown_cpus() during native_machine_emergency_restart().
Invoke the callback _before_ disabling virtualization, as the current
VMCS needs to be cleared before doing VMXOFF. Note, this results in a
subtle change in ordering between disabling virtualization and stopping
Intel PT on the responding CPUs. While VMX and Intel PT do interact,
VMXOFF and writes to MSR_IA32_RTIT_CTL do not induce faults between one
another, which is all that matters when panicking.
Harden nmi_shootdown_cpus() against multiple invocations to try and
capture any such kernel bugs via a WARN instead of hanging the system
during a crash/dump, e.g. prior to the recent hardening of
register_nmi_handler(), re-registering the NMI handler would trigger a
double list_add() and hang the system if CONFIG_BUG_ON_DATA_CORRUPTION=y.
Extract the disabling logic to a common helper to deduplicate code, and
to prepare for doing the shootdown in the emergency reboot path if SVM
is supported.
Note, prior to commit 36c1906aacc7 ("x86/reboot: Force all cpus to exit
VMX root if VMX is supported"), nmi_shootdown_cpus() was subtly protected
against a second invocation by a cpu_vmx_enabled() check as the kdump
handler would disable VMX if it ran first.
Fixes: 36c1906aacc7 ("x86/reboot: Force all cpus to exit VMX root if VMX is supported") Cc: stable@vger.kernel.org Reported-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Link: https://lore.kernel.org/all/20220427224924.592546-2-gpiccoli@igalia.com Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20221130233650.1404148-2-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set GIF=1 prior to disabling SVM to ensure that INIT is recognized if the
kernel is disabling SVM in an emergency, e.g. if the kernel is about to
jump into a crash kernel or may reboot without doing a full CPU RESET.
If GIF is left cleared, the new kernel (or firmware) will be unabled to
awaken APs. Eat faults on STGI (due to EFER.SVME=0) as it's possible
that SVM could be disabled via NMI shootdown between reading EFER.SVME
and executing STGI.
Migration mode is a VM attribute which enables tracking of changes in
storage attributes (PGSTE). It assumes dirty tracking is enabled on all
memslots to keep a dirty bitmap of pages with changed storage attributes.
When enabling migration mode, we currently check that dirty tracking is
enabled for all memslots. However, userspace can disable dirty tracking
without disabling migration mode.
Since migration mode is pointless with dirty tracking disabled, disable
migration mode whenever userspace disables dirty tracking on any slot.
Also update the documentation to clarify that dirty tracking must be
enabled when enabling migration mode, which is already enforced by the
code in kvm_s390_vm_start_migration().
Also highlight in the documentation for KVM_S390_GET_CMMA_BITS that it
can now fail with -EINVAL when dirty tracking is disabled while
migration mode is on. Move all the error codes to a table so this stays
readable.
To disable migration mode, slots_lock should be held, which is taken
in kvm_set_memory_region() and thus held in
kvm_arch_prepare_memory_region().
Restructure the prepare code a bit so all the sanity checking is done
before disabling migration mode. This ensures migration mode isn't
disabled when some sanity check fails.
Destroy and free the target coalesced MMIO device if unregistering said
device fails. As clearly noted in the code, kvm_io_bus_unregister_dev()
does not destroy the target device.
When we append new block just after the end of preallocated extent, the
code in inode_getblk() wrongly determined we're going to use the
preallocated extent which resulted in adding block into a wrong logical
offset in the file. Sequence like this manifests it:
The code that determined the use of preallocated extent is actually
stale because udf_do_extend_file() does not create preallocation anymore
so after calling that function we are sure there's no usable
preallocation. Just remove the faulty condition.
CC: stable@vger.kernel.org Fixes: 189b02ac597c ("udf: Discard preallocation before extending file with a hole") Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When UDF filesystem is corrupted, hidden system inodes can be linked
into directory hierarchy which is an avenue for further serious
corruption of the filesystem and kernel confusion as noticed by syzbot
fuzzed images. Refuse to access system inodes linked into directory
hierarchy and vice versa.
CC: stable@vger.kernel.org Reported-by: syzbot+38695a20b8addcbc1084@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System files in UDF filesystem have link count 0. To not confuse VFS we
fudge the link count to be 1 when reading such inodes however we forget
to restore the link count of 0 when writing such inodes. Fix that.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When write to inline file fails (or happens only partly), we still
updated length of inline data as if the whole write succeeded. Fix the
update of length of inline data to happen only if the write succeeds.
Reported-by: syzbot+0937935b993956ba28ab@syzkaller.appspotmail.com CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When merging very long extents we try to push as much length as possible
to the first extent. However this is unnecessarily complicated and not
really worth the trouble. Furthermore there was a bug in the logic
resulting in corrupting extents in the file as syzbot reproducer shows.
So just don't bother with the merging of extents that are too long
together.
CC: stable@vger.kernel.org Reported-by: syzbot+60f291a24acecb3c2bd5@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a file expansion failed because we didn't have enough space for
indirect extents make sure we truncate extents created so far so that we
don't leave extents beyond EOF.
CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes three issues on move extents ioctl without auto defrag:
a) In ocfs2_find_victim_alloc_group(), we have to convert bits to block
first in case of global bitmap.
b) In ocfs2_probe_alloc_group(), when finding enough bits in block
group bitmap, we have to back off move_len to start pos as well,
otherwise it may corrupt filesystem.
c) In ocfs2_ioctl_move_extents(), set me_threshold both for non-auto
and auto defrag paths. Otherwise it will set move_max_hop to 0 and
finally cause unexpectedly ENOSPC error.
Currently there are no tools triggering the above issues since
defragfs.ocfs2 enables auto defrag by default. Tested with manually
changing defragfs.ocfs2 to run non auto defrag path.
Link: https://lkml.kernel.org/r/20230220050526.22020-1-heming.zhao@suse.com Signed-off-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug has the same root cause of 'commit 05a5c6839af8 ("ocfs2: call
ocfs2_journal_access_di() before ocfs2_journal_dirty() in
ocfs2_write_end_nolock()")'. For this bug, jbd2_journal_restart() is
called by ocfs2_split_extent() during defragmenting.
How to fix
For ocfs2_split_extent() can handle journal operations totally by itself.
Caller doesn't need to call journal access/dirty pair, and caller only
needs to call journal start/stop pair. The fix method is to remove
journal access/dirty from __ocfs2_move_extent().
The discussion for this patch:
https://oss.oracle.com/pipermail/ocfs2-devel/2023-February/000647.html
Link: https://lkml.kernel.org/r/20230217003717.32469-1-heming.zhao@suse.com Signed-off-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When writing a page from an encrypted file that is using
filesystem-layer encryption (not inline encryption), f2fs encrypts the
pagecache page into a bounce page, then writes the bounce page.
It also passes the bounce page to wbc_account_cgroup_owner(). That's
incorrect, because the bounce page is a newly allocated temporary page
that doesn't have the memory cgroup of the original pagecache page.
This makes wbc_account_cgroup_owner() not account the I/O to the owner
of the pagecache page as it should.
Fix this by always passing the pagecache page to
wbc_account_cgroup_owner().
When converting an inline directory to a regular one, f2fs is leaking
uninitialized memory to disk because it doesn't initialize the entire
directory block. Fix this by zero-initializing the block.
This bug was introduced by commit 8c0c37f03ded ("f2fs: avoid unneeded
initializing when converting inline dentry"), which didn't consider the
security implications of leaking uninitialized memory to disk.
This was found by running xfstest generic/435 on a KMSAN-enabled kernel.
Fixes: 8c0c37f03ded ("f2fs: avoid unneeded initializing when converting inline dentry") Cc: <stable@vger.kernel.org> # v4.3+ Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current hfsplus_put_super first calls hfs_btree_close on
sbi->ext_tree, then invokes iput on sbi->hidden_dir, resulting in an
use-after-free issue in hfsplus_release_folio.
As shown in hfsplus_fill_super, the error handling code also calls iput
before hfs_btree_close.
To fix this error, we move all iput calls before hfsplus_btree_close.
Note that this patch is tested on Syzbot.
Link: https://lkml.kernel.org/r/20230226124948.3175736-1-mudongliangabcd@gmail.com Reported-by: syzbot+57e3e98f7e3b80f64d56@syzkaller.appspotmail.com Tested-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/* Dispose of resources used by a node */
void hfs_bnode_put(struct hfs_bnode *node)
{
if (node) {
<skipped>
BUG_ON(!atomic_read(&node->refcnt)); <- we have issue here!!!!
<skipped>
}
}
By tracing the refcnt, I found the node is created by hfs_bmap_alloc()
with refcnt 1. Then the node is used by hfs_btree_write(). There is a
missing of hfs_bnode_get() after find the node. The issue happened in
following path:
<alloc>
hfs_bmap_alloc
hfs_bnode_find
__hfs_bnode_create <- allocate a new node with refcnt 1.
hfs_bnode_put <- decrease the refcnt
<write>
hfs_btree_write
hfs_bnode_find
__hfs_bnode_create
hfs_bnode_findhash <- find the node without refcnt increased.
hfs_bnode_put <- trigger the BUG_ON() since refcnt is 0.
Link: https://lkml.kernel.org/r/20221212021627.3766829-1-liushixin2@huawei.com Reported-by: syzbot+5b04b49a7ec7226c7426@syzkaller.appspotmail.com Signed-off-by: Liu Shixin <liushixin2@huawei.com> Cc: Fabio M. De Francesco <fmdefrancesco@gmail.com> Cc: Viacheslav Dubeyko <slava@dubeyko.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent test_kprobe_missed kprobes kunit test uncovers the following
problem. Once kprobe is triggered from another kprobe (kprobe reenter),
all future kprobes on this cpu are considered as kprobe reenter, thus
pre_handler and post_handler are not being called and kprobes are counted
as "missed".
Commit ef41fee3efe0 ("[S390] kprobes: activation and deactivation")
introduced a simpler scheme for kprobes (de)activation and status
tracking by using push_kprobe/pop_kprobe, which supposed to work for
both initial kprobe entry as well as kprobe reentry and helps to avoid
handling those two cases differently. The problem is that a sequence of
calls in case of kprobes reenter:
push_kprobe() <- NULL (current_kprobe)
push_kprobe() <- kprobe1 (current_kprobe)
pop_kprobe() -> kprobe1 (current_kprobe)
pop_kprobe() -> kprobe1 (current_kprobe)
leaves "kprobe1" as "current_kprobe" on this cpu, instead of setting it
to NULL. In fact push_kprobe/pop_kprobe can only store a single state
(there is just one prev_kprobe in kprobe_ctlblk). Which is a hack but
sufficient, there is no need to have another prev_kprobe just to store
NULL. To make a simple and backportable fix simply reset "prev_kprobe"
when kprobe is poped from this "stack". No need to worry about
"kprobe_status" in this case, because its value is only checked when
current_kprobe != NULL.
Recent test_kprobe_missed kprobes kunit test uncovers the following error
(reported when CONFIG_DEBUG_ATOMIC_SLEEP is enabled):
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
in_atomic(): 0, irqs_disabled(): 1, non_block: 0, pid: 662, name: kunit_try_catch
preempt_count: 0, expected: 0
RCU nest depth: 0, expected: 0
no locks held by kunit_try_catch/662.
irq event stamp: 280
hardirqs last enabled at (279): [<00000003e60a3d42>] __do_pgm_check+0x17a/0x1c0
hardirqs last disabled at (280): [<00000003e3bd774a>] kprobe_exceptions_notify+0x27a/0x318
softirqs last enabled at (0): [<00000003e3c5c890>] copy_process+0x14a8/0x4c80
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 46 PID: 662 Comm: kunit_try_catch Tainted: G N 6.2.0-173644-g44c18d77f0c0 #2
Hardware name: IBM 3931 A01 704 (LPAR)
Call Trace:
[<00000003e60a3a00>] dump_stack_lvl+0x120/0x198
[<00000003e3d02e82>] __might_resched+0x60a/0x668
[<00000003e60b9908>] __mutex_lock+0xc0/0x14e0
[<00000003e60bad5a>] mutex_lock_nested+0x32/0x40
[<00000003e3f7b460>] unregister_kprobe+0x30/0xd8
[<00000003e51b2602>] test_kprobe_missed+0xf2/0x268
[<00000003e51b5406>] kunit_try_run_case+0x10e/0x290
[<00000003e51b7dfa>] kunit_generic_run_threadfn_adapter+0x62/0xb8
[<00000003e3ce30f8>] kthread+0x2d0/0x398
[<00000003e3b96afa>] __ret_from_fork+0x8a/0xe8
[<00000003e60ccada>] ret_from_fork+0xa/0x40
The reason for this error report is that kprobes handling code failed
to restore irqs.
The problem is that when kprobe is triggered from another kprobe
post_handler current sequence of enable_singlestep / disable_singlestep
is the following:
enable_singlestep <- original kprobe (saves kprobe_saved_imask)
enable_singlestep <- kprobe triggered from post_handler (clobbers kprobe_saved_imask)
disable_singlestep <- kprobe triggered from post_handler (restores kprobe_saved_imask)
disable_singlestep <- original kprobe (restores wrong clobbered kprobe_saved_imask)
There is just one kprobe_ctlblk per cpu and both calls saves and
loads irq mask to kprobe_saved_imask. To fix the problem simply move
resume_execution (which calls disable_singlestep) before calling
post_handler. This also fixes the problem that post_handler is called
with pt_regs which were not yet adjusted after single-stepping.
When debugging vmlinux with QEMU + GDB, the following GDB error may
occur:
(gdb) c
Continuing.
Warning:
Cannot insert breakpoint -1.
Cannot access memory at address 0xffffffffffff95c0
Command aborted.
(gdb)
The reason is that, when .interp section is present, GDB tries to
locate the file specified in it in memory and put a number of
breakpoints there (see enable_break() function in gdb/solib-svr4.c).
Sometimes GDB finds a bogus location that matches its heuristics,
fails to set a breakpoint and stops. This makes further debugging
impossible.
The .interp section contains misleading information anyway (vmlinux
does not need ld.so), so fix by discarding it.
Make sure to disable the alarm before updating the four alarm time
registers to avoid spurious alarms during the update.
Note that the disable needs to be done outside of the ctrl_reg_lock
section to prevent a racing alarm interrupt from disabling the newly set
alarm when the lock is released.
Fixes: 8b34661e0495 ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC") Cc: stable@vger.kernel.org # 3.1 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: David Collins <quic_collinsd@quicinc.com> Link: https://lore.kernel.org/r/20230202155448.6715-2-johan+linaro@kernel.org Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coreboot framebuffer doesn't support transparency, its 'reserved'
bit field is merely padding for byte/word alignment of pixel colors [1].
When trying to match the framebuffer to a simplefb format, the kernel
driver unnecessarily requires the format's transparency bit field to
exactly match this padding, even if the former is zero-width.
Due to a coreboot bug [2] (fixed upstream), some boards misreport the
reserved field's size as equal to its position (0x18 for both on a
'Lick' Chromebook), and the driver fails to probe where it would have
otherwise worked fine with e.g. the a8r8g8b8 or x8r8g8b8 formats.
Remove the transparency comparison with reserved bits. When the
bits-per-pixel and other color components match, transparency will
already be in a subset of the reserved field. Not forcing it to match
reserved bits allows the driver to work on the boards which misreport
the reserved field. It also enables using simplefb formats that don't
have transparency bits, although this doesn't currently happen due to
format support and ordering in linux/platform_data/simplefb.h.
At first, I thought this might be a source of nfsd_file overputs, but
the current callers seem to avoid an extra put when nfsd4_verify_copy
returns an error.
Still, it's "bad form" to leave the pointers filled out when we don't
have a reference to them anymore, and that might lead to bugs later.
Zero them out as a defensive coding measure.
Signed-off-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use devm_kasprintf() instead of kasprintf() to avoid any potential
leaks. At the moment drivers have no remove functionality thus
there is no need for fixes tag.
Coretemp's platform driver is unconventional. All the real work is done
globally by the initcall and CPU hotplug notifiers, while the "driver"
effectively just wraps an allocation and the registration of the hwmon
interface in a long-winded round-trip through the driver core. The whole
logic of dynamically creating and destroying platform devices to bring
the interfaces up and down is error prone, since it assumes
platform_device_add() will synchronously bind the driver and set drvdata
before it returns, thus results in a NULL dereference if drivers_autoprobe
is turned off for the platform bus. Furthermore, the unusual approach of
doing that from within a CPU hotplug notifier, already commented in the
code that it deadlocks suspend, also causes lockdep issues for other
drivers or subsystems which may want to legitimately register a CPU
hotplug notifier from a platform bus notifier.
All of these issues can be solved by ripping this unusual behaviour out
completely, simply tying the platform devices to the lifetime of the
module itself, and directly managing the hwmon interfaces from the
hotplug notifiers. There is a slight user-visible change in that
/sys/bus/platform/drivers/coretemp will no longer appear, and
/sys/devices/platform/coretemp.n will remain present if package n is
hotplugged off, but hwmon users should really only be looking for the
presence of the hwmon interfaces, whose behaviour remains unchanged.
The compiler has no way to know if "id" is within the array bounds of
the regulators array. Add a check for this and a build-time check that
the regulators and reg_voltage_map arrays are sized the same. Seen with
GCC 13:
../drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
../drivers/regulator/s5m8767.c:936:35: warning: array subscript [0, 36] is outside array bounds of 'struct regulator_desc[37]' [-Warray-bounds=]
936 | regulators[id].vsel_reg =
| ~~~~~~~~~~^~~~
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: linux-samsung-soc@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20230128005358.never.313-kees@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Walking the dram->cs array was seen as accesses beyond the first array
item by the compiler. Instead, use the array index directly. This allows
for run-time bounds checking under CONFIG_UBSAN_BOUNDS as well. Seen
with GCC 13 with -fstrict-flex-arrays:
../sound/soc/kirkwood/kirkwood-dma.c: In function
'kirkwood_dma_conf_mbus_windows.constprop':
../sound/soc/kirkwood/kirkwood-dma.c:90:24: warning: array subscript 0 is outside array bounds of 'const struct mbus_dram_window[0]' [-Warray-bounds=]
90 | if ((cs->base & 0xffff0000) < (dma & 0xffff0000)) {
| ~~^~~~~~
Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20230127224128.never.410-kees@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
iio was allocated in atom_index_iio() called by atom_parse(),
but it doesn't got released when the dirver is shutdown.
Fix this kmemleak by free it in radeon_atombios_fini().
Signed-off-by: Liwei Song <liwei.song@windriver.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Fixing smatch error:
dm_resume() error: we previously assumed 'aconnector->dc_link' could be null
[How]
Check if dc_link null at the beginning of the loop,
so further checks can be dropped.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Wayne Lin <Wayne.Lin@amd.com> Acked-by: Jasdeep Dhillon <jdhillon@amd.com> Signed-off-by: Roman Li <roman.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While there is logic about the difference between ksize and usize,
copy_struct_from_user() didn't check the size of the destination buffer
(when it was known) against ksize. Add this check so there is an upper
bounds check on the possible memset() call, otherwise lower bounds
checks made by callers will trigger bounds warnings under -Warray-bounds.
Seen under GCC 13:
In function 'copy_struct_from_user',
inlined from 'iommufd_fops_ioctl' at
../drivers/iommu/iommufd/main.c:333:8:
../include/linux/fortify-string.h:59:33: warning: '__builtin_memset' offset [57, 4294967294] is out of the bounds [0, 56] of object 'buf' with type 'union ucmd_buffer' [-Warray-bounds=]
59 | #define __underlying_memset __builtin_memset
| ^
../include/linux/fortify-string.h:453:9: note: in expansion of macro '__underlying_memset'
453 | __underlying_memset(p, c, __fortify_size); \
| ^~~~~~~~~~~~~~~~~~~
../include/linux/fortify-string.h:461:25: note: in expansion of macro '__fortify_memset_chk'
461 | #define memset(p, c, s) __fortify_memset_chk(p, c, s, \
| ^~~~~~~~~~~~~~~~~~~~
../include/linux/uaccess.h:334:17: note: in expansion of macro 'memset'
334 | memset(dst + size, 0, rest);
| ^~~~~~
../drivers/iommu/iommufd/main.c: In function 'iommufd_fops_ioctl':
../drivers/iommu/iommufd/main.c:311:27: note: 'buf' declared here
311 | union ucmd_buffer buf;
| ^~~
GCC does not like having a partially allocated object, since it cannot
reason about it for bounds checking when it is passed to other code.
Instead, fully allocate sig_inputArgs. (Alternatively, sig_inputArgs
should be defined as a struct coda_in_hdr, if it is actually not using
any other part of the union.) Seen under GCC 13:
../fs/coda/upcall.c: In function 'coda_upcall':
../fs/coda/upcall.c:801:22: warning: array subscript 'union inputArgs[0]' is partly outside array bounds of 'unsigned char[20]' [-Warray-bounds=]
801 | sig_inputArgs->ih.opcode = CODA_SIGNAL;
| ^~
Multiple Ideapad Z570 variants need acpi_backlight=native to force native
use on these pre Windows 8 machines since acpi_video backlight control
does not work here.
The original DMI quirk matches on a product_name of "102434U" but other
variants may have different product_name-s such as e.g. "1024D9U".
Move to checking product_version instead as is more or less standard for
Lenovo DMI quirks for similar reasons.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Occasionnaly we may get oversized packets from the hardware which
exceed the nomimal 2KiB buffer size we allocate SKBs with. Add an early
check which drops the packet to avoid invoking skb_over_panic() and move
on to processing the next packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This prevents CONFIG_FUNCTION_ALIGNMENT and
CONFIG_DEBUG_FORCE_FUNCTION_ALIGN_64B from having their expected effect
on the ACPICA code. This is doubly unfortunate as in subsequent patches
arm64 will depend upon CONFIG_FUNCTION_ALIGNMENT for its ftrace
implementation.
Drop the '-Os' flag when building the ACPICA code. With this removed,
the code builds cleanly and works correctly in testing so far.
I've tested this by selecting CONFIG_DEBUG_FORCE_FUNCTION_ALIGN_64B=y,
building and booting a kernel using ACPI, and looking for misaligned
text symbols:
With the patch applied, the remaining unaligned text labels are a
combination of static call trampolines and labels in assembly, which can
be dealt with in subsequent patches.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Florent Revest <revest@chromium.org> Cc: Len Brown <lenb@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Moore <robert.moore@intel.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Will Deacon <will@kernel.org> Cc: linux-acpi@vger.kernel.org Link: https://lore.kernel.org/r/20230123134603.1064407-4-mark.rutland@arm.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There were a few places we had missed checking the VSI type to make sure
it was definitely a PF VSI, before calling setup functions intended only
for the PF VSI.
This doesn't fix any explicit bugs but cleans up the code in a few
places and removes one explicit != vsi->type check that can be
superseded by this code (it's a super set)
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
__inet_hash_connect() has a fast path taken if sk_head(&tb->owners) is
equal to the sk parameter.
sk_head() returns the hlist_entry() with respect to the sk_node field.
However entries in the tb->owners list are inserted with respect to the
sk_bind_node field with sk_add_bind_node().
Thus the check would never pass and the fast path never execute.
This fast path has never been executed or tested as this bug seems
to be present since commit 1da177e4c3f4 ("Linux-2.6.12-rc2"), thus
remove it to reduce code complexity.
Fix an integer underflow that leads to a null pointer dereference in
'mt7601u_rx_skb_from_seg()'. The variable 'dma_len' in the URB packet
could be manipulated, which could trigger an integer underflow of
'seg_len' in 'mt7601u_rx_process_seg()'. This underflow subsequently
causes the 'bad_frame' checks in 'mt7601u_rx_skb_from_seg()' to be
bypassed, eventually leading to a dereference of the pointer 'p', which
is a null pointer.
Ensure that 'dma_len' is greater than 'min_seg_len'.
Fix a stack-out-of-bounds read in brcmfmac that occurs
when 'buf' that is not null-terminated is passed as an argument of
strreplace() in brcmf_c_preinit_dcmds(). This buffer is filled with
a CLM version string by memcpy() in brcmf_fil_iovar_data_get().
Ensure buf is null-terminated.
Currently, x86_spec_ctrl_base is read at boot time and speculative bits
are set if Kconfig items are enabled. For example, IBRS is enabled if
CONFIG_CPU_IBRS_ENTRY is configured, etc. These MSR bits are not cleared
if the mitigations are disabled.
This is a problem when kexec-ing a kernel that has the mitigation
disabled from a kernel that has the mitigation enabled. In this case,
the MSR bits are not cleared during the new kernel boot. As a result,
this might have some performance degradation that is hard to pinpoint.
This problem does not happen if the machine is (hard) rebooted because
the bit will be cleared by default.
The nanosleep syscalls use the restart_block mechanism, with a quirk:
The `type` and `rmtp`/`compat_rmtp` fields are set up unconditionally on
syscall entry, while the rest of the restart_block is only set up in the
unlikely case that the syscall is actually interrupted by a signal (or
pseudo-signal) that doesn't have a signal handler.
If the restart_block was set up by a previous syscall (futex(...,
FUTEX_WAIT, ...) or poll()) and hasn't been invalidated somehow since then,
this will clobber some of the union fields used by futex_wait_restart() and
do_restart_poll().
If userspace afterwards wrongly calls the restart_syscall syscall,
futex_wait_restart()/do_restart_poll() will read struct fields that have
been clobbered.
This doesn't actually lead to anything particularly interesting because
none of the union fields contain trusted kernel data, and
futex(..., FUTEX_WAIT, ...) and poll() aren't syscalls where it makes much
sense to apply seccomp filters to their arguments.
So the current consequences are just of the "if userspace does bad stuff,
it can damage itself, and that's not a problem" flavor.
But still, it seems like a hazard for future developers, so invalidate the
restart_block when partly setting it up in the nanosleep syscalls.
The return value from the call to intel_tcc_get_tjmax() is int, which can
be a negative error code. However, the return value is being assigned to
an u32 variable 'tj_max', so making 'tj_max' an int.
Eliminate the following warning:
./drivers/thermal/intel/intel_soc_dts_iosf.c:394:5-11: WARNING: Unsigned expression compared with zero: tj_max < 0
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3637 Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The normal grace period's RCU CPU stall warnings are invoked from the
scheduling-clock interrupt handler, and can thus invoke smp_processor_id()
with impunity, which allows them to directly invoke dump_cpu_task().
In contrast, the expedited grace period's RCU CPU stall warnings are
invoked from process context, which causes the dump_cpu_task() function's
calls to smp_processor_id() to complain bitterly in debug kernels.
This commit therefore causes synchronize_rcu_expedited_wait() to disable
preemption around its call to dump_cpu_task().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes a stack-out-of-bounds read in brcmfmac that occurs
when 'buf' that is not null-terminated is passed as an argument of
strsep() in brcmf_c_preinit_dcmds(). This buffer is filled with a firmware
version string by memcpy() in brcmf_fil_iovar_data_get().
The patch ensures buf is null-terminated.
Reported-by: Dokyung Song <dokyungs@yonsei.ac.kr> Reported-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr> Reported-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Signed-off-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221115043458.37562-1-jisoo.jang@yonsei.ac.kr Signed-off-by: Sasha Levin <sashal@kernel.org>
calc_lcoefs() uses the input value of cost.model in DIV_ROUND_UP_ULL,
overflow would happen if bps plus IOC_PAGE_SIZE is greater than
ULLONG_MAX, it can cause divide by 0 error.
For some reason, the driver adding support for Exynos5420 MIPI phy
back in 2016 wasn't used on Exynos5420, which caused a kernel panic.
Add the proper compatible for it.
In the event that an intent advertisement arrives on an unknown channel
the fifo is not advanced, resulting in the same message being handled
over and over.
Fixes: e4d845bba4c1 ("rpmsg: glink: Receive and store the remote intent buffers") Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> Reviewed-by: Chris Lew <quic_clew@quicinc.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230214234231.2069751-1-quic_bjorande@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When smscore_start_device() gets failed, the function smsusb_term_device()
will be called and smsusb_device_t will be deallocated. Although we use
usb_kill_urb() in smsusb_stop_streaming() to cancel transfer requests
and wait for them to finish, the worker threads that are scheduled by
smsusb_onresponse() may be still running. As a result, the UAF bugs
could happen.
We add cancel_work_sync() in smsusb_stop_streaming() in order that the
worker threads could finish before the smsusb_device_t is deallocated.
When the ene device is detaching, function ene_remove() will
be called. But there is no function to cancel tx_sim_timer
in ene_remove(), the timer handler ene_tx_irqsim() could race
with ene_remove(). As a result, the UAF bugs could happen,
the process is shown below.
Fix by adding del_timer_sync(&dev->tx_sim_timer) in ene_remove(),
The tx_sim_timer could stop before ene device is deallocated.
What's more, The rc_unregister_device() and del_timer_sync()
should be called first in ene_remove() and the deallocated
functions such as free_irq(), release_region() and so on
should be called behind them. Because the rc_unregister_device()
is well synchronized. Otherwise, race conditions may happen. The
situations that may lead to race conditions are shown below.
Firstly, the rx receiver is disabled with ene_rx_disable()
before rc_unregister_device() in ene_remove(), which means it
can be enabled again if a process opens /dev/lirc0 between
ene_rx_disable() and rc_unregister_device().
Secondly, the irqaction descriptor is freed by free_irq()
before the rc device is unregistered, which means irqaction
descriptor may be accessed again after it is deallocated.
Thirdly, the timer can call ene_tx_sample() that can write
to the io ports, which means the io ports could be accessed
again after they are deallocated by release_region().
Therefore, the rc_unregister_device() and del_timer_sync()
should be called first in ene_remove().
The reason is that if priv->hdl.error is set, ov772x_probe() jumps to the
error_mutex_destroy without doing v4l2_ctrl_handler_free(), and all
resources allocated in v4l2_ctrl_handler_init() and v4l2_ctrl_new_std()
are leaked.
ov5675_init_controls() won't clean all the allocated resources in fail
path, which may causes the memleaks. Add v4l2_ctrl_handler_free() to
prevent memleak.
Fixes: cb63633b9e8c ("media: ov5675: Add support for OV5675 sensor") Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This was likely supposed to be '-Wa,-a$(BITS)'. However, this change is
unnecessary, as all supported versions of clang and gcc will pass '-a64'
or '-a32' to GNU as based on the value of '-m'; the behavior of the
latest stable release of the oldest supported major version of each
compiler is shown below and each compiler's latest release exhibits the
same behavior (GCC 12.2.0 and Clang 15.0.6).
$ powerpc64-linux-gcc --version | head -1
powerpc64-linux-gcc (GCC) 5.5.0
Any access to the dynamically allocated metadata region by the application
processor after assigning it to the remote Q6 will result in a XPU
violation. Fix this by replacing the dynamically allocated memory region
with a no-map carveout and unmap the modem metadata memory region before
passing control to the remote Q6.
Reported-and-tested-by: Amit Pundir <amit.pundir@linaro.org> Fixes: a2ed97bf0e19 ("remoteproc: qcom: Make secure world call for mem ownership switch") Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230117085840.32356-7-quic_sibis@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When neither LANTIQ nor MIPS_MALTA is set, 'physical_memsize' is not
declared. This causes the build to fail with:
mips-linux-ld: arch/mips/kernel/vpe-mt.o: in function `vpe_run':
arch/mips/kernel/vpe-mt.c:(.text.vpe_run+0x280): undefined reference to `physical_memsize'
LANTIQ is not using 'physical_memsize' and MIPS_MALTA's use of it is
self-contained in mti-malta/malta-dtshim.c.
Use of physical_memsize in vpe-mt.c appears to be unused, so eliminate
this loader mode completely and require VPE programs to be compiled with
DFLT_STACK_SIZE and DFLT_HEAP_SIZE defined.
Fixes: e4a0ddf8b0b0 ("MIPS: lantiq: Set physical_memsize") Fixes: c463e94ccf54 ("MIPS: APRP: Split VPE loader into separate files.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/all/202302030625.2g3E98sY-lkp@intel.com/ Cc: Dengcheng Zhu <dzhu@wavecomp.com> Cc: John Crispin <john@phrozen.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Philippe Mathieu-Daudé <philmd@linaro.org> Cc: "Steven J. Hill" <Steven.Hill@imgtec.com> Cc: Qais Yousef <Qais.Yousef@imgtec.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When MIPS_CPS=y, MIPS_CPS_PM is not set, HOTPLUG_CPU is not set, and
KEXEC=y, cps_shutdown_this_cpu() attempts to call cps_pm_enter_state(),
which is not built when MIPS_CPS_PM is not set.
Conditionally execute the else branch based on CONFIG_HOTPLUG_CPU
to remove the build error.
This build failure is from a randconfig file.
mips-linux-ld: arch/mips/kernel/smp-cps.o: in function `$L162':
smp-cps.c:(.text.cps_kexec_nonboot_cpu+0x31c): undefined reference to `cps_pm_enter_state'
Fixes: 1524c02cd65a ("MIPS: kexec: CPS systems to halt nonboot CPUs") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Dengcheng Zhu <dzhu@wavecomp.com> Cc: Paul Burton <paulburton@kernel.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a PCI error is encountered 6th time in an hour we
set the channel state to perm_failure and notify the
driver about the permanent failure.
However, after upstream commit 57d8ee8925f4 ("powerpc/eeh:
Make permanently failed devices non-actionable"), EEH handler
stops calling any routine once the device is marked as
permanent failure. This issue can lead to fatal consequences
like kernel hang with certain PCI devices.
Following log is observed with lpfc driver, with and without
this change, Without this change kernel hangs, If PCI error
is encountered 6 times for a device in an hour.
Without the change
EEH: Beginning: 'error_detected(permanent failure)'
PCI 0132:60:00.0#600000: EEH: not actionable (1,1,1)
PCI 0132:60:00.1#600000: EEH: not actionable (1,1,1)
EEH: Finished:'error_detected(permanent failure)'
The control flow of eeh_handle_normal_event() is a bit tricky.
Break out one of the error handling paths - rather than be in an else
block, we'll make it part of the regular body of the function and put a
'goto out;' in the true limb of the if.
Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20211015070628.1331635-1-dja@axtens.net
Stable-dep-of: 9efcdaac36e1 ("powerpc/eeh: Set channel state after notifying the drivers") Signed-off-by: Sasha Levin <sashal@kernel.org>
4KB is the greatest alignment required by PAPR for such
buffers. rtas_data_buf used to have a __page_aligned attribute in the
arch/ppc64 days, but that was changed to __cacheline_aligned for
unknown reasons by commit dbb3d2cc0533 ("powerpc: Merge rtas.c into
arch/powerpc/kernel"). That works out to 128-byte alignment
on ppc64, which isn't right.
This was found by inspection and I'm not aware of any real problems
caused by this. Either current RTAS implementations don't enforce the
alignment constraints, or rtas_data_buf is always being placed at a
4KB boundary by accident (or both, perhaps).
Use __aligned(SZ_4K) to ensure the rtas_data_buf has alignment
appropriate for all users.
At the time this was applied, EXPORT_SYMBOL_GPL() was very new, and
the exports of rtas_call() etc have remained non-GPL. As new APIs have
been added to the RTAS subsystem, their symbol exports have followed
the convention set by existing code.
However, the historical evidence is that RTAS function exports have been
added over time only to satisfy the needs of in-kernel users, and these
clients must have fairly intimate knowledge of how the APIs work to use
them safely. No out of tree users are known, and future ones seem
unlikely.
Arguably the default for RTAS symbols should have become
EXPORT_SYMBOL_GPL once it was available. Let's make it so now, and
exceptions can be evaluated as needed.
In the previous commits that added CLK_OPS_PARENT_ENABLE, support for
this flag was only added to rate change operations (rate setting and
reparent) and disabling unused subtree. It was not added to the
clock gate related operations. Any hardware driver that needs it for
these operations will either see bogus results, or worse, hang.
This has been seen on MT8192 and MT8195, where the imp_ii2_* clk
drivers set this, but dumping debugfs clk_summary would cause it
to hang.
Prepare parent on prepare and enable parent on enable dependencies are
already handled automatically by the core as part of its sequencing.
Whether the case for "enable parent on prepare" should be supported by
this flag or not is not clear, and thus ignored for now.
This change solely fixes the handling of clk_core_is_enabled, i.e.
enabling the parent clock when reading the hardware state. Unfortunately
clk_core_is_enabled is called in a variety of places, sometimes with
the enable clock already held. To avoid deadlocking, the core will
ignore readouts and just return false if CLK_OPS_PARENT_ENABLE is set
but the parent isn't currently enabled.
Fixes: 7743310b682d ("clk: core: support clocks which requires parents enable (part 2)") Fixes: 6f67c1ebbbe7 ("clk: core: support clocks which requires parents enable (part 1)") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Link: https://lore.kernel.org/r/20230103092330.494102-1-wenst@chromium.org Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
pnv_ioda_setup_pe_res() calls opal to map a resource with a PE. However,
the code assumes the resource is allocated and it uses the resource
address to find out the segment(s) which need to be mapped to the
PE. In the unlikely case where the resource hasn't been allocated, the
computation for the segment number is garbage, which can lead to
invalid memory access and potentially a kernel crash, such as:
Hitting the problem is not that easy. It was seen with a (semi-bogus)
PCI device with a class code of 0. The generic PCI framework doesn't
allocate resources in such a case.
The patch is simply skipping resources which are still flagged with
IORESOURCE_UNSET.
We don't have the problem with 64-bit mem resources, as the address of
the resource is checked to be within the range of the 64-bit mmio
window. See pnv_ioda_reserve_dev_m64_pe() and pnv_pci_is_m64().
The gdsc_init() function will rewrite the CLK_DIS_WAIT field while
registering the GDSC (writing the value 0x2 by default). This will
override the setting done in the driver's probe function.
Set cx_gdsc.clk_dis_wait_val to 8 to follow the intention of the probe
function.
To discard false readings, one should use "ti,penirq-recheck-delay-usecs".
Checking get_pendown_state() at the beginning, most of the time fails
causing malfunctioning.
ADS7845 doesn't support pressure.
Avoid the following error reported by libinput-list-devices:
"ADS7845 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE".
When the code flow arrives at printing the error message in
cpg_mssr_resume_noirq(), we know for sure that we are not running on an
RZ/A Soc, as the code checked for that before.
Geert suggested defining multiple register layout variants using an enum
[1] to support further devices like R-Car V3U. So, use enum
clk_reg_layout instead of a boolean .stbyctrl flag. No behavioral
change.
If cpg_mssr_common_init() fails after assigning priv to global variable
cpg_mssr_priv, it deallocates priv, but cpg_mssr_priv keeps dangling
pointer that potentially can be used later.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
projects / kernel.git / log