nvmem: sunxi_sid: Read out SID for randomness without looping
Since the reg_read callbacks already support arbitrary, but 4-byte
aligned. offsets and lengths into the SID, there is no need for another
for loop just to use it to read 1 byte at a time.
Lucas Stach [Sat, 13 Apr 2019 10:32:48 +0000 (11:32 +0100)]
nvmem: imx-ocotp: broaden Kconfig dependency
The i.MX OCOTP controller is used in numerous Freescale/NXP
SoCs from the MXC family, so the strict dependency on the
i.MX6 SoC is too narrow. Broaden it to cover all the MXC
familiy members.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Abel Vesa <abel.vesa@nxp.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parport: ieee1284: mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/parport/ieee1284.c: In function ‘parport_read’:
drivers/parport/ieee1284.c:722:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (parport_negotiate (port, IEEE1284_MODE_NIBBLE)) {
^
drivers/parport/ieee1284.c:726:2: note: here
case IEEE1284_MODE_NIBBLE:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1: ds2408: reset on output_write retry with readback
When we have success in 'Channel Access Write' but reading back latch
states fails, a write is retried without doing a proper slave reset.
This leads to protocol errors as the slave treats the next 'Channel
Access Write' as the continuation of previous command.
This commit is fixing this by making sure if the retry loop re-runs, a
reset is performed, whatever the failure (CONFIRM_BYTE or the read
back).
The loop was quite due for a cleanup and this change mandated it. By
isolating the CONFIG_W1_SLAVE_DS2408_READBACK case into it's own
function, we vastly reduce the visual and branching(runtime and
compile-time) noise.
Merge tag 'icc-5.2-rc1' of https://git.linaro.org/people/georgi.djakov/linux into char-misc-next
Georgi writes:
interconnect: for 5.2
Here are some tiny patches for the 5.2-rc1 merge window:
- Add linux-pm@ as a mailing list for the interconnect API.
- Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.2-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
interconnect: convert to DEFINE_SHOW_ATTRIBUTE
MAINTAINERS: Add mailing list for the interconnect API
Expose mei device state to user-space through sysfs.
This gives indication to applications that driver is in transition,
usefully mostly to detect link reset state.
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patrick Venture [Mon, 8 Apr 2019 14:42:39 +0000 (07:42 -0700)]
drivers/misc: Add Aspeed P2A control driver
The ASPEED AST2400, and AST2500 in some configurations include a
PCI-to-AHB MMIO bridge. This bridge allows a server to read and write
in the BMC's physical address space. This feature is especially useful
when using this bridge to send large files to the BMC.
The host may use this to send down a firmware image by staging data at a
specific memory address, and in a coordinated effort with the BMC's
software stack and kernel, transmit the bytes.
This driver enables the BMC to unlock the PCI bridge on demand, and
configure it via ioctl to allow the host to write bytes to an agreed
upon location. In the primary use-case, the region to use is known
apriori on the BMC, and the host requests this information. Once this
request is received, the BMC's software stack will enable the bridge and
the region and then using some software flow control (possibly via IPMI
packets), copy the bytes down. Once the process is complete, the BMC
will disable the bridge and unset any region involved.
The default behavior of this bridge when present is: enabled and all
regions marked read-write. This driver will fix the regions to be
read-only and then disable the bridge entirely.
The memory regions protected are:
* BMC flash MMIO window
* System flash MMIO windows
* SOC IO (peripheral MMIO)
* DRAM
The DRAM region itself is all of DRAM and cannot be further specified.
Once the PCI bridge is enabled, the host can read all of DRAM, and if
the DRAM section is write-enabled, then it can write to all of it.
Signed-off-by: Patrick Venture <venture@google.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfix from Trond Myklebust:
"Fix a regression in which an RPC call can be tagged with an error
despite the transmission being successful"
* tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Ignore queue transmission errors on successful transmission
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: aic7xxx: fix EISA support
Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
scsi: core: set result when the command cannot be dispatched
Merge tag 'for-linus-20190420' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of small fixes that should go into this series. This contains:
- Removal of unused queue member (Hou)
- Overflow bvec fix (Ming)
- Various little io_uring tweaks (me)
- kthread parking
- Only call cpu_possible() for verified CPU
- Drop unused 'file' argument to io_file_put()
- io_uring_enter vs io_uring_register deadlock fix
- CQ overflow fix
- BFQ internal depth update fix (me)"
* tag 'for-linus-20190420' of git://git.kernel.dk/linux-block:
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
io_uring: fix CQ overflow condition
io_uring: fix possible deadlock between io_uring_{enter,register}
io_uring: drop io_file_put() 'file' argument
bfq: update internal depth state when queue depth changes
io_uring: only test SQPOLL cpu after we've verified it
io_uring: park SQPOLL thread if it's percpu
Merge tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pill i3c fixes from Boris Brezillon:
- fix the random PID check
- fix the disable controller logic in the designware driver
- fix I3C entry in MAINTAINERS
* tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
MAINTAINERS: Fix the I3C entry
i3c: dw: Fix dw_i3c_master_disable controller by using correct mask
i3c: Fix the verification of random PID
Merge tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Two core fixes for long-standing bugs for the races at concurrent
device creation and deletion that were (unsurprisingly) spotted by
syzkaller with usb-fuzzer.
The rest are usual small HD-audio fixes"
* tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - add two more pin configuration sets to quirk table
ALSA: core: Fix card races between register and disconnect
ALSA: info: Fix racy addition/deletion of nodes
ALSA: hda: Initialize power_state field properly
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes:
- various tooling fixes
- kretprobe fixes
- kprobes annotation fixes
- kprobes error checking fix
- fix the default events for AMD Family 17h CPUs
- PEBS fix
- AUX record fix
- address filtering fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Avoid kretprobe recursion bug
kprobes: Mark ftrace mcount handler functions nokprobe
x86/kprobes: Verify stack frame on kretprobe
perf/x86/amd: Add event map for AMD Family 17h
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_btf()
perf tools: Fix map reference counting
perf evlist: Fix side band thread draining
perf tools: Check maps for bpf programs
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_bpf_prog_info()
tools include uapi: Sync sound/asound.h copy
perf top: Always sample time to satisfy needs of use of ordered queuing
perf evsel: Use hweight64() instead of hweight_long(attr.sample_regs_user)
tools lib traceevent: Fix missing equality check for strcmp
perf stat: Disable DIR_FORMAT feature for 'perf stat record'
perf scripts python: export-to-sqlite.py: Fix use of parent_id in calls_view
perf header: Fix lock/unlock imbalances when processing BPF/BTF info
perf/x86: Fix incorrect PEBS_REGS
perf/ring_buffer: Fix AUX record suppression
perf/core: Fix the address filtering fix
kprobes: Fix error check when reusing optimized probes
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes all over the place: a console spam fix, section attributes
fixes, a KASLR fix, a TLB stack-variable alignment fix, a reboot
quirk, boot options related warnings fix, an LTO fix, a deadlock fix
and an RDT fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
x86/cpu/bugs: Use __initconst for 'const' init data
x86/mm/KASLR: Fix the size of the direct mapping section
x86/Kconfig: Fix spelling mistake "effectivness" -> "effectiveness"
x86/mm/tlb: Revert "x86/mm: Align TLB invalidation info"
x86/reboot, efi: Use EFI reboot for Acer TravelMate X514-51T
x86/mm: Prevent bogus warnings with "noexec=off"
x86/build/lto: Fix truncated .bss with -fdata-sections
x86/speculation: Prevent deadlock on ssb_state::lock
x86/resctrl: Do not repeat rdtgroup mode initialization
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A deadline scheduler warning/race fix, and a cfs_period_us quota
calculation workaround where the real fix looks too involved to merge
immediately"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Correctly handle active 0-lag timers
sched/fair: Limit sched_cfs_period_timer() loop to avoid hard lockup
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"A lockdep warning fix and a script execution fix when atomics are
generated"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/atomics: Don't assume that scripts are executable
locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again
Merge tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are five small fixes for some tty/serial/vt issues that have been
reported.
The vt one has been around for a while, it is good to finally get that
resolved. The others fix a build warning that showed up in 5.1-rc1,
and resolve a problem in the sh-sci driver.
Note, the second patch for build warning fix for the sc16is7xx driver
was just applied to the tree, as it resolves a problem with the
previous patch to try to solve the issue. It has not shown up in
linux-next yet, unlike all of the other patches, but it has passed
0-day testing and everyone seems to agree that it is correct"
* tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: put err_spi and err_i2c into correct #ifdef
vt: fix cursor when clearing the screen
sc16is7xx: move label 'err_spi' to correct section
serial: sh-sci: Fix HSCIF RX sampling point adjustment
serial: sh-sci: Fix HSCIF RX sampling point calculation
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
Merge tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here is a bunch of IIO driver fixes, and some smaller staging driver
fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
all resolve a number of reported issues and have been in linux-next
for a few weeks with no reported issues.
The other staging driver fixes are all tiny, resolving some reported
issues in the comedi and most drivers, as well as some erofs fixes.
All of these patches have been in linux-next with no reported issues"
* tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
staging: comedi: ni_usb6501: Fix use of uninitialized mutex
staging: erofs: fix unexpected out-of-bound data access
staging: comedi: vmk80xx: Fix possible double-free of ->usb_rx_buf
staging: comedi: vmk80xx: Fix use of uninitialized semaphore
staging: most: core: use device description as name
iio: core: fix a possible circular locking dependency
iio: ad_sigma_delta: select channel when reading register
iio: pms7003: select IIO_TRIGGERED_BUFFER
iio: cros_ec: Fix the maths for gyro scale calculation
iio: adc: xilinx: prevent touching unclocked h/w on remove
iio: adc: xilinx: fix potential use-after-free on probe
iio: adc: xilinx: fix potential use-after-free on remove
iio: dac: mcp4725: add missing powerdown bits in store eeprom
io: accel: kxcjk1013: restore the range after resume.
iio:chemical:bme680: Fix SPI read interface
iio:chemical:bme680: Fix, report temperature in millidegrees
iio: chemical: fix missing Kconfig block for sgp30
iio: adc: at91: disable adc channel interrupt in timeout case
iio: gyro: mpu3050: fix chip ID reading
...
Ming Lei [Wed, 17 Apr 2019 01:11:26 +0000 (09:11 +0800)]
block: make sure that bvec length can't be overflow
bvec->bv_offset may be bigger than PAGE_SIZE sometimes, such as,
when one bio is splitted in the middle of one bvec via bio_split(),
and bi_iter.bi_bvec_done is used to build offset of the 1st bvec of
remained bio. And the remained bio's bvec may be re-submitted to fs
layer via ITER_IBVEC, such as loop and nvme-loop.
So we have to make sure that every bvec's offset is less than
PAGE_SIZE from bio_for_each_segment_all() because some drivers(loop,
nvme-loop) passes the splitted bvec to fs layer via ITER_BVEC.
This patch fixes this issue reported by Zhang Yi When running nvme/011.
Cc: Christoph Hellwig <hch@lst.de> Cc: Yi Zhang <yi.zhang@redhat.com> Reported-by: Yi Zhang <yi.zhang@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Fixes: b3e229b9d9ee ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec") Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- several new key mappings for HID
- a host of new ACPI IDs used to identify Elan touchpads in Lenovo
laptops
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: snvs_pwrkey - initialize necessary driver data before enabling IRQ
HID: input: add mapping for "Toggle Display" key
HID: input: add mapping for "Full Screen" key
HID: input: add mapping for keyboard Brightness Up/Down/Toggle keys
HID: input: add mapping for Expose/Overview key
HID: input: fix mapping of aspect ratio key
[media] doc-rst: switch to new names for Full Screen/Aspect keys
Input: document meanings of KEY_SCREEN and KEY_ZOOM
Input: elan_i2c - add hardware ID for multiple Lenovo laptops
Hans de Goede [Sun, 30 Dec 2018 17:27:15 +0000 (18:27 +0100)]
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
The "ENERGY_PERF_BIAS: Set to 'normal', was 'performance'" message triggers
on pretty much every Intel machine. The purpose of log messages with
a warning level is to notify the user of something which potentially is
a problem, or at least somewhat unexpected.
This message clearly does not match those criteria, so lower its log
priority from warning to info.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20181230172715.17469-1-hdegoede@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge tag 'perf-urgent-for-mingo-5.1-20190419' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf top:
Jiri Olsa:
- Fix 'perf top --pid', it needs PERF_SAMPLE_TIME since we switched to using
a different thread to sort the events and then even for just a single
thread we now need timestamps.
BPF:
Jiri Olsa:
- Fix bpf_prog and btf lookup functions failure path to to properly return
NULL.
- Fix side band thread draining, used to process PERF_RECORD_BPF_EVENT
metadata records.
core:
Jiri Olsa:
- Fix map lookup by name to get a refcount when the name is already in
the tree. Found
Song Liu:
- Fix __map__is_kmodule() by taking into account recently added BPF
maps.
UAPI:
Arnaldo Carvalho de Melo:
- Sync sound/asound.h copy
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andrea Arcangeli [Fri, 19 Apr 2019 00:50:52 +0000 (17:50 -0700)]
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
The core dumping code has always run without holding the mmap_sem for
writing, despite that is the only way to ensure that the entire vma
layout will not change from under it. Only using some signal
serialization on the processes belonging to the mm is not nearly enough.
This was pointed out earlier. For example in Hugh's post from Jul 2017:
"Not strictly relevant here, but a related note: I was very surprised
to discover, only quite recently, how handle_mm_fault() may be called
without down_read(mmap_sem) - when core dumping. That seems a
misguided optimization to me, which would also be nice to correct"
In particular because the growsdown and growsup can move the
vm_start/vm_end the various loops the core dump does around the vma will
not be consistent if page faults can happen concurrently.
Pretty much all users calling mmget_not_zero()/get_task_mm() and then
taking the mmap_sem had the potential to introduce unexpected side
effects in the core dumping code.
Adding mmap_sem for writing around the ->core_dump invocation is a
viable long term fix, but it requires removing all copy user and page
faults and to replace them with get_dump_page() for all binary formats
which is not suitable as a short term fix.
For the time being this solution manually covers the places that can
confuse the core dump either by altering the vma layout or the vma flags
while it runs. Once ->core_dump runs under mmap_sem for writing the
function mmget_still_valid() can be dropped.
Allowing mmap_sem protected sections to run in parallel with the
coredump provides some minor parallelism advantage to the swapoff code
(which seems to be safe enough by never mangling any vma field and can
keep doing swapins in parallel to the core dumping) and to some other
corner case.
In order to facilitate the backporting I added "Fixes: 8f43b5eef139"
however the side effect of this same race condition in /proc/pid/mem
should be reproducible since before 2.6.12-rc2 so I couldn't add any
other "Fixes:" because there's no hash beyond the git genesis commit.
Because find_extend_vma() is the only location outside of the process
context that could modify the "mm" structures under mmap_sem for
reading, by adding the mmget_still_valid() check to it, all other cases
that take the mmap_sem for reading don't need the new check after
mmget_not_zero()/get_task_mm(). The expand_stack() in page fault
context also doesn't need the new check, because all tasks under core
dumping are frozen.
Link: http://lkml.kernel.org/r/20190325224949.11068-1-aarcange@redhat.com Fixes: 8f43b5eef139 ("userfaultfd: add new syscall to provide memory externalization") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Jann Horn <jannh@google.com> Suggested-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Peter Xu <peterx@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Reviewed-by: Jann Horn <jannh@google.com> Acked-by: Jason Gunthorpe <jgg@mellanox.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Fri, 19 Apr 2019 00:50:44 +0000 (17:50 -0700)]
init: initialize jump labels before command line option parsing
When a module option, or core kernel argument, toggles a static-key it
requires jump labels to be initialized early. While x86, PowerPC, and
ARM64 arrange for jump_label_init() to be called before parse_args(),
ARM does not.
Kernel command line: rdinit=/sbin/init page_alloc.shuffle=1 panic=-1 console=ttyAMA0,115200 page_alloc.shuffle=1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ./include/linux/jump_label.h:303
page_alloc_shuffle+0x12c/0x1ac
static_key_enable(): static key 'page_alloc_shuffle_key+0x0/0x4' used
before call to jump_label_init()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.1.0-rc4-next-20190410-00003-g3367c36ce744 #1
Hardware name: ARM Integrator/CP (Device Tree)
[<c0011c68>] (unwind_backtrace) from [<c000ec48>] (show_stack+0x10/0x18)
[<c000ec48>] (show_stack) from [<c07e9710>] (dump_stack+0x18/0x24)
[<c07e9710>] (dump_stack) from [<c001bb1c>] (__warn+0xe0/0x108)
[<c001bb1c>] (__warn) from [<c001bb88>] (warn_slowpath_fmt+0x44/0x6c)
[<c001bb88>] (warn_slowpath_fmt) from [<c0b0c4a8>]
(page_alloc_shuffle+0x12c/0x1ac)
[<c0b0c4a8>] (page_alloc_shuffle) from [<c0b0c550>] (shuffle_store+0x28/0x48)
[<c0b0c550>] (shuffle_store) from [<c003e6a0>] (parse_args+0x1f4/0x350)
[<c003e6a0>] (parse_args) from [<c0ac3c00>] (start_kernel+0x1c0/0x488)
Move the fallback call to jump_label_init() to occur before
parse_args().
The redundant calls to jump_label_init() in other archs are left intact
in case they have static key toggling use cases that are even earlier
than option parsing.
Link: http://lkml.kernel.org/r/155544804466.1032396.13418949511615676665.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reported-by: Guenter Roeck <groeck@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Russell King <rmk@armlinux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Rutland [Fri, 19 Apr 2019 00:50:37 +0000 (17:50 -0700)]
kcov: improve CONFIG_ARCH_HAS_KCOV help text
The help text for CONFIG_ARCH_HAS_KCOV is stale, and describes the
feature as being enabled only for x86_64, when it is now enabled for
several architectures, including arm, arm64, powerpc, and s390.
Let's remove that stale help text, and update it along the lines of hat
for ARCH_HAS_FORTIFY_SOURCE, better describing when an architecture
should select CONFIG_ARCH_HAS_KCOV.
Johannes Weiner [Fri, 19 Apr 2019 00:50:34 +0000 (17:50 -0700)]
mm: fix inactive list balancing between NUMA nodes and cgroups
During !CONFIG_CGROUP reclaim, we expand the inactive list size if it's
thrashing on the node that is about to be reclaimed. But when cgroups
are enabled, we suddenly ignore the node scope and use the cgroup scope
only. The result is that pressure bleeds between NUMA nodes depending
on whether cgroups are merely compiled into Linux. This behavioral
difference is unexpected and undesirable.
When the refault adaptivity of the inactive list was first introduced,
there were no statistics at the lruvec level - the intersection of node
and memcg - so it was better than nothing.
But now that we have that infrastructure, use lruvec_page_state() to
make the list balancing decision always NUMA aware.
[hannes@cmpxchg.org: fix bisection hole] Link: http://lkml.kernel.org/r/20190417155241.GB23013@cmpxchg.org Link: http://lkml.kernel.org/r/20190412144438.2645-1-hannes@cmpxchg.org Fixes: c9393956b236 ("mm: vmscan: fix IO/refault regression in cache workingset transition") Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Roman Gushchin <guro@fb.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Qian Cai [Fri, 19 Apr 2019 00:50:30 +0000 (17:50 -0700)]
mm/hotplug: treat CMA pages as unmovable
has_unmovable_pages() is used by allocating CMA and gigantic pages as
well as the memory hotplug. The later doesn't know how to offline CMA
pool properly now, but if an unused (free) CMA page is encountered, then
has_unmovable_pages() happily considers it as a free memory and
propagates this up the call chain. Memory offlining code then frees the
page without a proper CMA tear down which leads to an accounting issues.
Moreover if the same memory range is onlined again then the memory never
gets back to the CMA pool.
Also, kmemleak still think those memory address are reserved below but
have already been used by the buddy allocator after onlining. This
patch fixes the situation by treating CMA pageblocks as unmovable except
when has_unmovable_pages() is called as part of CMA allocation.
[cai@lca.pw: use is_migrate_cma_page() and update commit log] Link: http://lkml.kernel.org/r/20190416170510.20048-1-cai@lca.pw Link: http://lkml.kernel.org/r/20190413002623.8967-1-cai@lca.pw Signed-off-by: Qian Cai <cai@lca.pw> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Oscar Salvador <osalvador@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
Commit 681068f4a6c0 ("mm/vmstat.c: skip NR_TLB_REMOTE_FLUSH* properly")
depends on skipping vmstat entries with empty name introduced in 7877cc9afee7 ("mm: don't show nr_indirectly_reclaimable in
/proc/vmstat") but reverted in f59f2678f01a ("mm: rename and change
semantics of nr_indirectly_reclaimable_bytes").
So skipping no longer works and /proc/vmstat has misformatted lines " 0".
This patch simply shows debug counters "nr_tlb_remote_*" for UP.
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
When adding memory by probing a memory block in the sysfs interface,
there is an obvious issue where we will unlock the device_hotplug_lock
when we failed to takes it.
That issue was introduced in 6c615b6bae48 ("mm/memory_hotplug: make
add_memory() take the device_hotplug_lock").
We should drop out in time when failing to take the device_hotplug_lock.
Link: http://lkml.kernel.org/r/1554696437-9593-1-git-send-email-zhongjiang@huawei.com Fixes: 6c615b6bae48 ("mm/memory_hotplug: make add_memory() take the device_hotplug_lock") Signed-off-by: zhong jiang <zhongjiang@huawei.com> Reported-by: Yang yingliang <yangyingliang@huawei.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: swapoff: shmem_unuse() stop eviction without igrab()
The igrab() in shmem_unuse() looks good, but we forgot that it gives no
protection against concurrent unmounting: a point made by Konstantin
Khlebnikov eight years ago, and then fixed in 2.6.39 by 3ef34e05ad47
("tmpfs: fix race between umount and swapoff"). The current 5.1-rc
swapoff is liable to hit "VFS: Busy inodes after unmount of tmpfs.
Self-destruct in 5 seconds. Have a nice day..." followed by GPF.
Once again, give up on using igrab(); but don't go back to making such
heavy-handed use of shmem_swaplist_mutex as last time: that would spoil
the new design, and I expect could deadlock inside shmem_swapin_page().
Instead, shmem_unuse() just raise a "stop_eviction" count in the shmem-
specific inode, and shmem_evict_inode() wait for that to go down to 0.
Call it "stop_eviction" rather than "swapoff_busy" because it can be put
to use for others later (huge tmpfs patches expect to use it).
That simplifies shmem_unuse(), protecting it from both unlink and
unmount; and in practice lets it locate all the swap in its first try.
But do not rely on that: there's still a theoretical case, when
shmem_writepage() might have been preempted after its get_swap_page(),
before making the swap entry visible to swapoff.
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
SWAP_UNUSE_MAX_TRIES 3 appeared to work well in earlier testing, but
further testing has proved it to be a source of unnecessary swapoff
EBUSY failures (which can then be followed by unmount EBUSY failures).
When mmget_not_zero() or shmem's igrab() fails, there is an mm exiting
or inode being evicted, freeing up swap independent of try_to_unuse().
Those typically completed much sooner than the old quadratic swapoff,
but now it's more common that swapoff may need to wait for them.
It's possible to move those cases from init_mm.mmlist and shmem_swaplist
to separate "exiting" swaplists, and try_to_unuse() then wait for those
lists to be emptied; but we've not bothered with that in the past, and
don't want to risk missing some other forgotten case. So just revert to
cycling around until the swap is gone, without any retries limit.
mm: swapoff: shmem_find_swap_entries() filter out other types
Swapfile "type" was passed all the way down to shmem_unuse_inode(), but
then forgotten from shmem_find_swap_entries(): with the result that
removing one swapfile would try to free up all the swap from shmem - no
problem when only one swapfile anyway, but counter-productive when more,
causing swapoff to be unnecessarily OOM-killed when it should succeed.
Qian Cai [Fri, 19 Apr 2019 00:49:55 +0000 (17:49 -0700)]
slab: store tagged freelist for off-slab slabmgmt
Commit c30cac8dff00 ("kasan, slab: make freelist stored without tags")
calls kasan_reset_tag() for off-slab slab management object leading to
freelist being stored non-tagged.
However, cache_grow_begin() calls alloc_slabmgmt() which calls
kmem_cache_alloc_node() assigns a tag for the address and stores it in
the shadow address. As the result, it causes endless errors below
during boot due to drain_freelist() -> slab_destroy() ->
kasan_slab_free() which compares already untagged freelist against the
stored tag in the shadow address.
Since off-slab slab management object freelist is such a special case,
just store it tagged. Non-off-slab management object freelist is still
stored untagged which has not been assigned a tag and should not cause
any other troubles with this inconsistency.
BUG: KASAN: double-free or invalid-free in slab_destroy+0x84/0x88
Pointer tag: [ff], memory tag: [99]
The buggy address belongs to the object at ffff809681b89e00
which belongs to the cache kmalloc-128 of size 128
The buggy address is located 0 bytes inside of
128-byte region [ffff809681b89e00, ffff809681b89e80)
The buggy address belongs to the page:
page:ffff7fe025a06e00 count:1 mapcount:0 mapping:01ff80082000fb00
index:0xffff809681b8fe04
flags: 0x17ffffffc000200(slab)
raw: 017ffffffc000200ffff7fe025a06d08ffff7fe022ef7b8801ff80082000fb00
raw: ffff809681b8fe04ffff809681b8000000000001000000e00000000000000000
page dumped because: kasan: bad access detected
page allocated via order 0, migratetype Unmovable, gfp_mask
0x2420c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_COMP|__GFP_THISNODE)
prep_new_page+0x4e0/0x5e0
get_page_from_freelist+0x4ce8/0x50d4
__alloc_pages_nodemask+0x738/0x38b8
cache_grow_begin+0xd8/0xa24
____cache_alloc_node+0x14c/0x268
__kmalloc+0x1c8/0x3fc
ftrace_free_mem+0x408/0x1284
ftrace_free_init_mem+0x20/0x28
kernel_init+0x24/0x548
ret_from_fork+0x10/0x18
Memory state around the buggy address: ffff809681b89c00: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe ffff809681b89d00: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
>ffff809681b89e00: 99 99 99 99 99 99 99 99 fe fe fe fe fe fe fe fe
^ ffff809681b89f00: 43 43 43 43 43 fe fe fe fe fe fe fe fe fe fe fe ffff809681b8a000: 6d fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
Link: http://lkml.kernel.org/r/20190403022858.97584-1-cai@lca.pw Fixes: c30cac8dff00 ("kasan, slab: make freelist stored without tags") Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Andrey Konovalov <andreyknvl@google.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Masami Hiramatsu [Sat, 23 Feb 2019 16:50:49 +0000 (01:50 +0900)]
x86/kprobes: Avoid kretprobe recursion bug
Avoid kretprobe recursion loop bg by setting a dummy
kprobes to current_kprobe per-CPU variable.
This bug has been introduced with the asm-coded trampoline
code, since previously it used another kprobe for hooking
the function return placeholder (which only has a nop) and
trampoline handler was called from that kprobe.
This revives the old lost kprobe again.
With this fix, we don't see deadlock anymore.
And you can see that all inner-called kretprobe are skipped.
event_1 235 0
event_2 19375 19612
The 1st column is recorded count and the 2nd is missed count.
Above shows (event_1 rec) + (event_2 rec) ~= (event_2 missed)
(some difference are here because the counter is racy)
Reported-by: Andrea Righi <righi.andrea@gmail.com> Tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: b4420d7d2627 ("[PATCH] kretprobe: kretprobe-booster") Link: http://lkml.kernel.org/r/155094064889.6137.972160690963039.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org>
Masami Hiramatsu [Sat, 23 Feb 2019 16:50:20 +0000 (01:50 +0900)]
kprobes: Mark ftrace mcount handler functions nokprobe
Mark ftrace mcount handler functions nokprobe since
probing on these functions with kretprobe pushes
return address incorrectly on kretprobe shadow stack.
Reported-by: Francis Deslauriers <francis.deslauriers@efficios.com> Tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/155094062044.6137.6419622920568680640.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org>
Masami Hiramatsu [Sat, 23 Feb 2019 16:49:52 +0000 (01:49 +0900)]
x86/kprobes: Verify stack frame on kretprobe
Verify the stack frame pointer on kretprobe trampoline handler,
If the stack frame pointer does not match, it skips the wrong
entry and tries to find correct one.
This can happen if user puts the kretprobe on the function
which can be used in the path of ftrace user-function call.
Such functions should not be probed, so this adds a warning
message that reports which function should be blacklisted.
Tested-by: Andrea Righi <righi.andrea@gmail.com> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/155094059185.6137.15527904013362842072.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org>
sc16is7xx: put err_spi and err_i2c into correct #ifdef
err_spi is only called within SERIAL_SC16IS7XX_SPI
while err_i2c is called inside SERIAL_SC16IS7XX_I2C.
So we need to put err_spi and err_i2c into each #ifdef
accordingly.
This change fixes ("sc16is7xx: move label 'err_spi'
to correct section").
Merge tag 'misc-habanalabs-next-2019-04-19' of git://people.freedesktop.org/~gabbayo/linux into char-misc-next
Oded writes:
This tag contains many changes for kernel 5.2.
The major changes are:
- Add a new IOCTL for debug, profiling and trace operations on the device.
This will allow the user to perform profiling and debugging of the
deep learning topologies that are executing on the ASIC.
- Add a shadow table for the ASIC's MMU page tables to avoid doing page
table walks on the device's DRAM during map/unmap operations.
- re-factor of ASIC-dependent code to be common code for all ASICs
In addition, there are many small fixes and changes. The notable ones are:
- Allow accessing the DRAM using virtual address through the debugFS
interface. Until now, only physical addresses were valid, but that is
useless for debugging when working with MMU.
- Allow the user to modify the TPC clock relaxation value to better
control TPC power consumption during topology execution.
- Allow the user to inquire about the device's status
(operational/Malfunction/in-reset) in the INFO IOCTL.
- Improvements to the device's removal function, to prevent crash in case
of force removal by the OS.
- Prevent PTE read/write during hard-reset. This will improve stability of
the device during hard-reset.
* tag 'misc-habanalabs-next-2019-04-19' of git://people.freedesktop.org/~gabbayo/linux: (31 commits)
habanalabs: prevent device PTE read/write during hard-reset
habanalabs: improve IOCTLs behavior when disabled or reset
habanalabs: all FD must be closed before removing device
habanalabs: split mmu/no-mmu code paths in memory ioctl
habanalabs: ASIC_AUTO_DETECT enum value is redundant
habanalabs: refactoring in goya.c
uapi/habanalabs: fix some comments in uapi file
habanalabs: add goya implementation for debug configuration
habanalabs: add new IOCTL for debug, tracing and profiling
habanalabs: remove extra semicolon
habanalabs: prevent CPU soft lockup on Palladium
habanalabs: remove trailing blank line from EOF
habanalabs: improve error messages
habanalabs: add device status option to INFO IOCTL
habanalabs: allow user to modify TPC clock relaxation value
habanalabs: set new golden value to tpc clock relaxation
habanalabs: never fail hard reset of device
habanalabs: keep track of the device's dma mask
habanalabs: add MMU shadow mapping
habanalabs: Allow accessing DRAM virtual addresses via debugfs
...
Instead of relying on the now removed NULL argument to
pci_alloc_consistent, switch to the generic DMA API, and store the struct
device so that we can pass it.
Fixes: 3816cf8898b6 ("PCI: Remove NULL device handling from PCI DMA API") Reported-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Matthew Whitehead <tedheadster@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Avoid compiler uninitialised warning introduced by recent arm64 futex
fix"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: futex: Restore oldval initialization to work around buggy compilers
arm64: futex: Restore oldval initialization to work around buggy compilers
Commit 2c6482567488 ("arm64: futex: Fix FUTEX_WAKE_OP atomic ops with
non-zero result value") removed oldval's zero initialization in
arch_futex_atomic_op_inuser because it is not necessary. Unfortunately,
Android's arm64 GCC 4.9.4 [1] does not agree:
../kernel/futex.c: In function 'do_futex':
../kernel/futex.c:1658:17: warning: 'oldval' may be used uninitialized
in this function [-Wmaybe-uninitialized]
return oldval == cmparg;
^
In file included from ../kernel/futex.c:73:0:
../arch/arm64/include/asm/futex.h:53:6: note: 'oldval' was declared here
int oldval, ret, tmp;
^
GCC fails to follow that when ret is non-zero, futex_atomic_op_inuser
returns right away, avoiding the uninitialized use that it claims.
Restoring the zero initialization works around this issue.
As stated in the original commit for pidfd_send_signal() we don't allow
to signal processes through O_PATH file descriptors since it is
semantically equivalent to a write on the pidfd.
We already correctly error out right now and return EBADF if an O_PATH
fd is passed. This is because we use file->f_op to detect whether a
pidfd is passed and O_PATH fds have their file->f_op set to empty_fops
in do_dentry_open() and thus fail the test.
Thus, there is no regression. It's just semantically correct to use
fdget() and return an error right from there instead of taking a
reference and returning an error later.
Signed-off-by: Christian Brauner <christian@brauner.io> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Kees Cook <keescook@chromium.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jann Horn <jann@thejh.net> Cc: David Howells <dhowells@redhat.com> Cc: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com> Cc: Andy Lutomirsky <luto@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Aleksa Sarai <cyphar@cyphar.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 's390-5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 bug fixes from Martin Schwidefsky:
- Fix overwrite of the initial ramdisk due to misuse of IS_ENABLED
- Fix integer overflow in the dasd driver resulting in incorrect number
of blocks for large devices
- Fix a lockdep false positive in the 3270 driver
- Fix a deadlock in the zcrypt driver
- Fix incorrect debug feature entries in the pkey api
- Fix inline assembly constraints fallout with CONFIG_KASAN=y
* tag 's390-5.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: correct some inline assembly constraints
s390/pkey: add one more argument space for debug feature entry
s390/zcrypt: fix possible deadlock situation on ap queue remove
s390/3270: fix lockdep false positive on view->lock
s390/dasd: Fix capacity calculation for large volumes
s390/mem_detect: Use IS_ENABLED(CONFIG_BLK_DEV_INITRD)
Merge tag 'afs-fixes-20190413' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
- Stop using the deprecated get_seconds().
- Don't make tracepoint strings const as the section they go in isn't
read-only.
- Differentiate failure due to unmarshalling from other failure cases.
We shouldn't abort with RXGEN_CC/SS_UNMARSHAL if it's not due to
unmarshalling.
- Add a missing unlock_page().
- Fix the interaction between receiving a notification from a server
that it has invalidated all outstanding callback promises and a
client call that we're in the middle of making that will get a new
promise.
* tag 'afs-fixes-20190413' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix in-progess ops to ignore server-level callback invalidation
afs: Unlock pages for __pagevec_release()
afs: Differentiate abort due to unmarshalling from other errors
afs: Avoid section confusion in CM_NAME
afs: avoid deprecated get_seconds()
Merge tag 'drm-fixes-2019-04-18' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Since Easter is looming for me, I'm just pushing whatever is in my
tree, I'll see what else turns up and maybe I'll send another pull
early next week if there is anything.
tegra:
- stream id programming fix
- avoid divide by 0 for bad hdmi audio setup code
amdgpu:
- GPU VM fixes for Vega/RV
- DC AUX fix for active DP-DVI dongles
- DC fix for multihead regression"
* tag 'drm-fixes-2019-04-18' of git://anongit.freedesktop.org/drm/drm:
drm/tegra: hdmi: Setup audio only if configured
drm/amd/display: If one stream full updates, full update all planes
drm/amdgpu/gmc9: fix VM_L2_CNTL3 programming
drm/amdgpu: shadow in shadow_list without tbo.mem.start cause page fault in sriov TDR
gpu: host1x: Program stream ID to bypass without SMMU
drm/amd/display: extending AUX SW Timeout
drm/ttm: fix dma_fence refcount imbalance on error path
drm/ttm: fix incrementing the page pointer for huge pages
drm/ttm: fix start page for huge page check in ttm_put_pages()
drm/ttm: fix out-of-bounds read in ttm_put_pages() v2
Chang-An Chen [Fri, 29 Mar 2019 02:59:09 +0000 (10:59 +0800)]
timers/sched_clock: Prevent generic sched_clock wrap caused by tick_freeze()
tick_freeze() introduced by suspend-to-idle in commit 9aa312d6fc2c ("PM /
sleep: Make it possible to quiesce timers during suspend-to-idle") uses
timekeeping_suspend() instead of syscore_suspend() during
suspend-to-idle. As a consequence generic sched_clock will keep going
because sched_clock_suspend() and sched_clock_resume() are not invoked
during suspend-to-idle which can result in a generic sched_clock wrap.
On a ARM system with suspend-to-idle enabled, sched_clock is registered
as "56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns", which
means the real wrapping duration is 8796093022202ns.
sched_clock was not stopped during suspend-to-idle, and sched_clock_poll
hrtimer was not expired because timekeeping_suspend() was invoked during
suspend-to-idle. It makes sched_clock wrap at kernel time 8796s.
To prevent this, invoke sched_clock_suspend() and sched_clock_resume() in
tick_freeze() together with timekeeping_suspend() and timekeeping_resume().
Fixes: 9aa312d6fc2c (PM / sleep: Make it possible to quiesce timers during suspend-to-idle) Signed-off-by: Chang-An Chen <chang-an.chen@mediatek.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Kees Cook <keescook@chromium.org> Cc: Corey Minyard <cminyard@mvista.com> Cc: <linux-mediatek@lists.infradead.org> Cc: <linux-arm-kernel@lists.infradead.org> Cc: Stanley Chu <stanley.chu@mediatek.com> Cc: <kuohong.wang@mediatek.com> Cc: <freddy.hsin@mediatek.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/1553828349-8914-1-git-send-email-chang-an.chen@mediatek.com
Kim Phillips [Thu, 21 Mar 2019 21:15:22 +0000 (21:15 +0000)]
perf/x86/amd: Add event map for AMD Family 17h
Family 17h differs from prior families by:
- Does not support an L2 cache miss event
- It has re-enumerated PMC counters for:
- L2 cache references
- front & back end stalled cycles
So we add a new amd_f17h_perfmon_event_map[] so that the generic
perf event names will resolve to the correct h/w events on
family 17h and above processors.
Reference sections 2.1.13.3.3 (stalls) and 2.1.13.3.6 (L2):
Baoquan He [Thu, 4 Apr 2019 02:03:13 +0000 (10:03 +0800)]
x86/mm/KASLR: Fix the size of the direct mapping section
kernel_randomize_memory() uses __PHYSICAL_MASK_SHIFT to calculate
the maximum amount of system RAM supported. The size of the direct
mapping section is obtained from the smaller one of the below two
values:
(actual system RAM size + padding size) vs (max system RAM size supported)
This calculation is wrong since commit
bd5db5675bb2 ("x86/mm/64: Make __PHYSICAL_MASK_SHIFT always 52").
In it, __PHYSICAL_MASK_SHIFT was changed to be 52, regardless of whether
the kernel is using 4-level or 5-level page tables. Thus, it will always
use 4 PB as the maximum amount of system RAM, even in 4-level paging
mode where it should actually be 64 TB.
Thus, the size of the direct mapping section will always
be the sum of the actual system RAM size plus the padding size.
Even when the amount of system RAM is 64 TB, the following layout will
still be used. Obviously KALSR will be weakened significantly.
The size of padding region is controlled by
CONFIG_RANDOMIZE_MEMORY_PHYSICAL_PADDING, which is 10 TB by default.
The above issue only exists when
CONFIG_RANDOMIZE_MEMORY_PHYSICAL_PADDING is set to a non-zero value,
which is the case when CONFIG_MEMORY_HOTPLUG is enabled. Otherwise,
using __PHYSICAL_MASK_SHIFT doesn't affect KASLR.
Fix it by replacing __PHYSICAL_MASK_SHIFT with MAX_PHYSMEM_BITS.
[ bp: Massage commit message. ]
Fixes: bd5db5675bb2 ("x86/mm/64: Make __PHYSICAL_MASK_SHIFT always 52") Signed-off-by: Baoquan He <bhe@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Thomas Garnier <thgarnie@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: frank.ramsay@hpe.com Cc: herbert@gondor.apana.org.au Cc: kirill@shutemov.name Cc: mike.travis@hpe.com Cc: thgarnie@google.com Cc: x86-ml <x86@kernel.org> Cc: yamada.masahiro@socionext.com Link: https://lkml.kernel.org/r/20190417083536.GE7065@MiWiFi-R3L-srv
Dave Airlie [Wed, 17 Apr 2019 20:56:26 +0000 (06:56 +1000)]
Merge branch 'drm-fixes-5.1' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
- GPUVM fixes for vega/RV and shadow buffers
- TTM fixes for hugepages
- TTM fix for refcount imbalance in error path
- DC AUX fix for some active DP-DVI dongles
- DC fix for multihead VT switch regression
Dave Airlie [Wed, 17 Apr 2019 20:55:34 +0000 (06:55 +1000)]
Merge tag 'drm/tegra/for-5.1-rc6' of git://anongit.freedesktop.org/tegra/linux into drm-fixes
drm/tegra: Fixes for v5.1-rc6
This contains a follow-up fix for the stream ID programming and a fix
for a regression on older Tegra devices (Tegra20 and Tegra30) that are
running into a division by zero trying to enable audio over HDMI.
Merge tag '5.1-rc5-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull smb3 fixes from Steve French:
"Five small SMB3 fixes, all also for stable - an important fix for an
oplock (lease) bug, a handle leak, and three bugs spotted by KASAN"
* tag '5.1-rc5-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: keep FileInfo handle live during oplock break
cifs: fix handle leak in smb2_query_symlink()
cifs: Fix lease buffer length error
cifs: Fix use-after-free in SMB2_read
cifs: Fix use-after-free in SMB2_write
SUNRPC: Ignore queue transmission errors on successful transmission
If a request transmission fails due to write space or slot unavailability
errors, but the queued task then gets transmitted before it has time to
process the error in call_transmit_status() or call_bc_transmit_status(),
we need to suppress the transmission error code to prevent it from leaking
out of the RPC layer.
Reported-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Tested-by: Chuck Lever <chuck.lever@oracle.com>
This is a leftover from when the rings initially were not free flowing,
and hence a test for tail + 1 == head would indicate full. Since we now
let them wrap instead of mask them with the size, we need to check if
they drift more than the ring size from each other.
This fixes a case where we'd overwrite CQ ring entries, if the user
failed to reap completions. Both cases would ultimately result in lost
completions as the application violated the depth it asked for. The only
difference is that before this fix we'd return invalid entries for the
overflowed completions, instead of properly flagging it in the
cq_ring->overflow variable.
Reported-by: Stefan Bühler <source@stbuehler.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jiri Olsa [Wed, 17 Apr 2019 14:55:39 +0000 (16:55 +0200)]
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_btf()
We don't return NULL when we don't find the bpf_prog_info_node, fix
that.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Reported-by: Song Liu <songliubraving@fb.com> Acked-by: Song Liu <songliubraving@fb.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: a7bc1ef9833a ("perf bpf: Save BTF in a rbtree in perf_env") Link: http://lkml.kernel.org/r/20190417145539.11669-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jiri Olsa [Tue, 16 Apr 2019 16:01:24 +0000 (18:01 +0200)]
perf tools: Fix map reference counting
By calling maps__insert() we assume to get 2 references on the map,
which we relese within maps__remove call.
However if there's already same map name, we currently don't bump the
reference and can crash, like:
Program received signal SIGABRT, Aborted.
0x00007ffff75e60f5 in raise () from /lib64/libc.so.6
(gdb) bt
#0 0x00007ffff75e60f5 in raise () from /lib64/libc.so.6
#1 0x00007ffff75d0895 in abort () from /lib64/libc.so.6
#2 0x00007ffff75d0769 in __assert_fail_base.cold () from /lib64/libc.so.6
#3 0x00007ffff75de596 in __assert_fail () from /lib64/libc.so.6
#4 0x00000000004fc006 in refcount_sub_and_test (i=1, r=0x1224e88) at tools/include/linux/refcount.h:131
#5 refcount_dec_and_test (r=0x1224e88) at tools/include/linux/refcount.h:148
#6 map__put (map=0x1224df0) at util/map.c:299
#7 0x00000000004fdb95 in __maps__remove (map=0x1224df0, maps=0xb17d80) at util/map.c:953
#8 maps__remove (maps=0xb17d80, map=0x1224df0) at util/map.c:959
#9 0x00000000004f7d8a in map_groups__remove (map=<optimized out>, mg=<optimized out>) at util/map_groups.h:65
#10 machine__process_ksymbol_unregister (sample=<optimized out>, event=0x7ffff7279670, machine=<optimized out>) at util/machine.c:728
#11 machine__process_ksymbol (machine=<optimized out>, event=0x7ffff7279670, sample=<optimized out>) at util/machine.c:741
#12 0x00000000004fffbb in perf_session__deliver_event (session=0xb11390, event=0x7ffff7279670, tool=0x7fffffffc7b0, file_offset=13936) at util/session.c:1362
#13 0x00000000005039bb in do_flush (show_progress=false, oe=0xb17e80) at util/ordered-events.c:243
#14 __ordered_events__flush (oe=0xb17e80, how=OE_FLUSH__ROUND, timestamp=<optimized out>) at util/ordered-events.c:322
#15 0x00000000005005e4 in perf_session__process_user_event (session=session@entry=0xb11390, event=event@entry=0x7ffff72a4af8,
...
Add the map to the list and getting the reference event if we find the
map with same name.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Eric Saint-Etienne <eric.saint.etienne@oracle.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Fixes: ac32a60a0569 ("perf symbols: Fix slowness due to -ffunction-section") Link: http://lkml.kernel.org/r/20190416160127.30203-10-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jiri Olsa [Tue, 16 Apr 2019 16:01:23 +0000 (18:01 +0200)]
perf evlist: Fix side band thread draining
Current perf_evlist__poll_thread() code could finish without draining
the data. Adding the logic that makes sure we won't finish before the
drain.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Fixes: ccc6a592ad1b ("perf evlist: Introduce side band thread") Link: http://lkml.kernel.org/r/20190416160127.30203-9-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Jiri Olsa [Tue, 16 Apr 2019 13:41:51 +0000 (15:41 +0200)]
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_bpf_prog_info()
We currently don't return NULL in case we don't find the
bpf_prog_info_node, fixing that.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Song Liu <songliubraving@fb.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Fixes: 8aae545b2fa7 ("perf bpf: Save bpf_prog_info in a rbtree in perf_env") Link: http://lkml.kernel.org/r/20190416134151.15282-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Merge tag 'for-linus-5.1-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"Fixes for some bugs cause by recent changes. One crash if you feed bad
data to the module parameters, one BUG that sometimes occurs when a
user closes the connection, and one bug that cause the driver to not
work if the configuration information only comes in from SMBIOS"
* tag 'for-linus-5.1-2' of git://github.com/cminyard/linux-ipmi:
ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier
ipmi: ipmi_si_hardcode.c: init si_type array to fix a crash
ipmi: Fix failure on SMBIOS specified devices
The patch f6e6cc492f8c ("vt: perform safe console erase in the right
order") introduced a bug. The conditional do_update_region() was
replaced by a call to update_region() that does contain the conditional
already, but with unwanted extra side effects such as restoring the cursor
drawing.
In order to reproduce the bug:
- use framebuffer console with the AMDGPU driver
- type "links" to start the console www browser
- press 'q' and space to exit links
Now the cursor will be permanently visible in the center of the
screen. It will stay there until something overwrites it.
The bug goes away if we change update_region() back to the conditional
do_update_region().
[ nico: reworded changelog ]
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reviewed-by: Nicolas Pitre <nico@fluxnic.net> Cc: stable@vger.kernel.org Fixes: f6e6cc492f8c ("vt: perform safe console erase in the right order") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Abbott [Mon, 15 Apr 2019 11:43:02 +0000 (12:43 +0100)]
staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
`ni6501_alloc_usb_buffers()` is called from `ni6501_auto_attach()` to
allocate RX and TX buffers for USB transfers. It allocates
`devpriv->usb_rx_buf` followed by `devpriv->usb_tx_buf`. If the
allocation of `devpriv->usb_tx_buf` fails, it frees
`devpriv->usb_rx_buf`, leaving the pointer set dangling, and returns an
error. Later, `ni6501_detach()` will be called from the core comedi
module code to clean up. `ni6501_detach()` also frees both
`devpriv->usb_rx_buf` and `devpriv->usb_tx_buf`, but
`devpriv->usb_rx_buf` may have already beed freed, leading to a
double-free error. Fix it bu removing the call to
`kfree(devpriv->usb_rx_buf)` from `ni6501_alloc_usb_buffers()`, relying
on `ni6501_detach()` to free the memory.
Ian Abbott [Mon, 15 Apr 2019 11:43:01 +0000 (12:43 +0100)]
staging: comedi: ni_usb6501: Fix use of uninitialized mutex
If `ni6501_auto_attach()` returns an error, the core comedi module code
will call `ni6501_detach()` to clean up. If `ni6501_auto_attach()`
successfully allocated the comedi device private data, `ni6501_detach()`
assumes that a `struct mutex mut` contained in the private data has been
initialized and uses it. Unfortunately, there are a couple of places
where `ni6501_auto_attach()` can return an error after allocating the
device private data but before initializing the mutex, so this
assumption is invalid. Fix it by initializing the mutex just after
allocating the private data in `ni6501_auto_attach()` before any other
errors can be retturned. Also move the call to `usb_set_intfdata()`
just to keep the code a bit neater (either position for the call is
fine).
I believe this was the cause of the following syzbot crash report
<https://syzkaller.appspot.com/bug?extid=cf4f2b6c24aff0a3edf6>:
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
usb 1-1: config 0 descriptor??
usb 1-1: string descriptor 0 read error: -71
comedi comedi0: Wrong number of endpoints
ni6501 1-1:0.233: driver 'ni6501' failed to auto-configure device.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 585 Comm: kworker/0:3 Not tainted 5.1.0-rc4-319354-g9a33b36 #3
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xe8/0x16e lib/dump_stack.c:113
assign_lock_key kernel/locking/lockdep.c:786 [inline]
register_lock_class+0x11b8/0x1250 kernel/locking/lockdep.c:1095
__lock_acquire+0xfb/0x37c0 kernel/locking/lockdep.c:3582
lock_acquire+0x10d/0x2f0 kernel/locking/lockdep.c:4211
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0xfe/0x12b0 kernel/locking/mutex.c:1072
ni6501_detach+0x5b/0x110 drivers/staging/comedi/drivers/ni_usb6501.c:567
comedi_device_detach+0xed/0x800 drivers/staging/comedi/drivers.c:204
comedi_device_cleanup.part.0+0x68/0x140 drivers/staging/comedi/comedi_fops.c:156
comedi_device_cleanup drivers/staging/comedi/comedi_fops.c:187 [inline]
comedi_free_board_dev.part.0+0x16/0x90 drivers/staging/comedi/comedi_fops.c:190
comedi_free_board_dev drivers/staging/comedi/comedi_fops.c:189 [inline]
comedi_release_hardware_device+0x111/0x140 drivers/staging/comedi/comedi_fops.c:2880
comedi_auto_config.cold+0x124/0x1b0 drivers/staging/comedi/drivers.c:1068
usb_probe_interface+0x31d/0x820 drivers/usb/core/driver.c:361
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_set_configuration+0xdf7/0x1740 drivers/usb/core/message.c:2021
generic_probe+0xa2/0xda drivers/usb/core/generic.c:210
usb_probe_device+0xc0/0x150 drivers/usb/core/driver.c:266
really_probe+0x2da/0xb10 drivers/base/dd.c:509
driver_probe_device+0x21d/0x350 drivers/base/dd.c:671
__device_attach_driver+0x1d8/0x290 drivers/base/dd.c:778
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:454
__device_attach+0x223/0x3a0 drivers/base/dd.c:844
bus_probe_device+0x1f1/0x2a0 drivers/base/bus.c:514
device_add+0xad2/0x16e0 drivers/base/core.c:2106
usb_new_device.cold+0x537/0xccf drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x138e/0x3b00 drivers/usb/core/hub.c:5432
process_one_work+0x90f/0x1580 kernel/workqueue.c:2269
worker_thread+0x9b/0xe20 kernel/workqueue.c:2415
kthread+0x313/0x420 kernel/kthread.c:253
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
Hui Wang [Wed, 17 Apr 2019 08:10:32 +0000 (16:10 +0800)]
ALSA: hda/realtek - add two more pin configuration sets to quirk table
We have two Dell laptops which have the codec 10ec0236 and 10ec0256
respectively, the headset mic on them can't work, need to apply the
quirk of ALC255_FIXUP_DELL1_MIC_NO_PRESENCE. So adding their pin
configurations in the pin quirk table.
Cc: <stable@vger.kernel.org> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Inline assembly code changed in this patch should really use "Q"
constraint "Memory reference without index register and with short
displacement". The kernel build with kasan instrumentation enabled
might occasionally break otherwise (due to stack instrumentation).
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The audio configuration is only valid if the HDMI codec has been
properly set up. Do not attempt to set up audio before that happens
because it causes a division by zero.
Note that this is only problematic on Tegra20 and Tegra30. Later chips
implement the division instructions which return zero when dividing by
zero and don't throw an exception.
Fixes: 12037a0f6ac0 ("drm/tegra: hdmi: Fix audio to work with any pixel clock rate") Reported-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Tested-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
It looks like the new socket options only work correctly
for native execution, but in case of compat mode fall back
to the old behavior as we ignore the 'old_timeval' flag.
Rework so we treat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW the
same way in compat and native 32-bit mode.
Cc: Deepa Dinamani <deepa.kernel@gmail.com> Fixes: ca8198f4f80e ("sock: Add SO_RCVTIMEO_NEW and SO_SNDTIMEO_NEW") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 16 Apr 2019 17:55:20 +0000 (10:55 -0700)]
tcp: tcp_grow_window() needs to respect tcp_space()
For some reason, tcp_grow_window() correctly tests if enough room
is present before attempting to increase tp->rcv_ssthresh,
but does not prevent it to grow past tcp_space()
This is causing hard to debug issues, like failing
the (__tcp_select_window(sk) >= tp->rcv_wnd) test
in __tcp_ack_snd_check(), causing ACK delays and possibly
slow flows.
Depending on tcp_rmem[2], MTU, skb->len/skb->truesize ratio,
we can see the problem happening on "netperf -t TCP_RR -- -r 2000,2000"
after about 60 round trips, when the active side no longer sends
immediate acks.
This bug predates git history.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: fix netlink export of vlan_stats_per_port option
Since the introduction of the vlan_stats_per_port option the netlink
export of it has been broken since I made a typo and used the ifla
attribute instead of the bridge option to retrieve its state.
Sysfs export is fine, only netlink export has been affected.
Fixes: a0f3c17c04dd3 ("net: bridge: add support for per-port vlan stats") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 16 Apr 2019 11:43:17 +0000 (12:43 +0100)]
qed: fix spelling mistake "faspath" -> "fastpath"
There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Liu [Tue, 16 Apr 2019 05:10:09 +0000 (13:10 +0800)]
tipc: set sysctl_tipc_rmem and named_timeout right range
We find that sysctl_tipc_rmem and named_timeout do not have the right minimum
setting. sysctl_tipc_rmem should be larger than zero, like sysctl_tcp_rmem.
And named_timeout as a timeout setting should be not less than zero.
Fixes: 4f71b04283e1a ("tipc: change socket buffer overflow control to respect sk_rcvbuf") Fixes: d607469a7f8bc ("tipc: add name distributor resiliency queue") Signed-off-by: Jie Liu <liujie165@huawei.com> Reported-by: Qiang Ning <ningqiang1@huawei.com> Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According to the link FSM, when a link endpoint got RESET_MSG (- a
traditional one without the stopping bit) from its peer, it moves to
PEER_RESET state and raises a LINK_DOWN event which then resets the
link itself. Its state will become ESTABLISHING after the reset event
and the link will be re-established soon after this endpoint starts to
send ACTIVATE_MSG to the peer.
There is no problem with this mechanism, however the link resetting has
cleared the link 'in_session' flag (along with the other important link
data such as: the link 'mtu') that was correctly set up at the 1st step
(i.e. when this endpoint received the peer RESET_MSG). As a result, the
link will become ESTABLISHED, but the 'in_session' flag is not set, and
all STATE_MSG from its peer will be dropped at the link_validate_msg().
It means the link not synced and will sooner or later face a failure.
Since the link reset action is obviously needed for a new link session
(this is also true in the other situations), the problem here is that
the link is re-established a bit too early when the link endpoints are
not really in-sync yet. The commit forces a resync as already done in
the previous commit 06836b36c226 ("tipc: fix link session and
re-establish issues") by simply varying the link 'peer_session' value
at the link_reset().
Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix missing meta data in skb with vlan packet
skb_reorder_vlan_header() should move XDP meta data with ethernet header
if XDP meta data exists.
Fixes: 344eaa193a76 ("bpf: add meta pointer for direct access") Signed-off-by: Yuya Kusakabe <yuya.kusakabe@gmail.com> Signed-off-by: Takeru Hayasaka <taketarou2@gmail.com> Co-developed-by: Takeru Hayasaka <taketarou2@gmail.com> Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix this by sanitizing arg before using it to index dev_lec.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
net/core: work around section mismatch warning for ptp_classifier
The routine ptp_classifier_init() uses an initializer for an
automatic struct type variable which refers to an __initdata
symbol. This is perfectly legal, but may trigger a section
mismatch warning when running the compiler in -fpic mode, due
to the fact that the initializer may be emitted into an anonymous
.data section thats lack the __init annotation. So work around it
by using assignments instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When the commit below was introduced it changed two visible things:
- the skb was no longer passed through the protocol handlers with the
original device
- the skb was passed up the stack with skb->dev = bridge
The first change broke af_packet sockets on bridge ports. For example we
use them for hostapd which listens for ETH_P_PAE packets on the ports.
We discussed two possible fixes:
- create a clone and pass it through NF_HOOK(), act on the original skb
based on the result
- somehow signal to the caller from the okfn() that it was called,
meaning the skb is ok to be passed, which this patch is trying to
implement via returning 1 from the bridge link-local okfn()
Note that we rely on the fact that NF_QUEUE/STOLEN would return 0 and
drop/error would return < 0 thus the okfn() is called only when the
return was 1, so we signal to the caller that it was called by preserving
the return value from nf_hook().
Fixes: 5f7bf977db3c ("bridge: fix potential use-after-free when hook returns QUEUE or STOLEN verdict") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Camuso [Tue, 9 Apr 2019 19:20:03 +0000 (15:20 -0400)]
ipmi: ipmi_si_hardcode.c: init si_type array to fix a crash
The intended behavior of function ipmi_hardcode_init_one() is to default
to kcs interface when no type argument is presented when initializing
ipmi with hard coded addresses.
However, the array of char pointers allocated on the stack by function
ipmi_hardcode_init() was not inited to zeroes, so it contained stack
debris.
Consequently, passing the cruft stored in this array to function
ipmi_hardcode_init_one() caused a crash when it was unable to detect
that the char * being passed was nonsense and tried to access the
address specified by the bogus pointer.
The fix is simply to initialize the si_type array to zeroes, so if
there were no type argument given to at the command line, function
ipmi_hardcode_init_one() could properly default to the kcs interface.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Message-Id: <1554837603-40299-1-git-send-email-tcamuso@redhat.com> Signed-off-by: Corey Minyard <cminyard@mvista.com>
projects / kernel.git / log