Linus Torvalds [Sun, 10 Nov 2019 20:07:47 +0000 (12:07 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Make the tsc=reliable/nowatchdog command line parameter work again.
It was broken with the introduction of the early TSC clocksource.
- Prevent the evaluation of exception stacks before they are set up.
This causes a crash in dumpstack because the stack walk termination
gets screwed up.
- Prevent a NULL pointer dereference in the rescource control file
system.
- Avoid bogus warnings about APIC id mismatch related to the LDR
which can happen when the LDR is not in use and therefore not
initialized. Only evaluate that when the APIC is in logical
destination mode"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Respect tsc command line paraemeter for clocksource_tsc_early
x86/dumpstack/64: Don't evaluate exception stacks before setup
x86/apic/32: Avoid bogus LDR warnings
x86/resctrl: Prevent NULL pointer dereference when reading mondata
Linus Torvalds [Sun, 10 Nov 2019 20:03:58 +0000 (12:03 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for timekeepoing and clocksource drivers:
- VDSO data was updated conditional on the availability of a VDSO
capable clocksource. This causes the VDSO functions which do not
depend on a VDSO capable clocksource to operate on stale data.
Always update unconditionally.
- Prevent a double free in the mediatek driver
- Use the proper helper in the sh_mtu2 driver so it won't attempt to
initialize non-existing interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Update VDSO data unconditionally
clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
clocksource/drivers/mediatek: Fix error handling
Linus Torvalds [Sun, 10 Nov 2019 20:00:47 +0000 (12:00 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two fixes for scheduler regressions:
- Plug a subtle race condition which was introduced with the rework
of the next task selection functionality. The change of task
properties became unprotected which can be observed inconsistently
causing state corruption.
- A trivial compile fix for CONFIG_CGROUPS=n"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix pick_next_task() vs 'change' pattern race
sched/core: Fix compilation error when cgroup not selected
Linus Torvalds [Sun, 10 Nov 2019 19:51:11 +0000 (11:51 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixlet from Thomas Gleixner:
"A trivial fix for a kernel doc regression where an argument change was
not reflected in the documentation"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq/irqdomain: Update __irq_domain_alloc_fwnode() function documentation
Linus Torvalds [Sat, 9 Nov 2019 16:51:37 +0000 (08:51 -0800)]
Merge tag 'for-5.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"A few regressions and fixes for stable.
Regressions:
- fix a race leading to metadata space leak after task received a
signal
- un-deprecate 2 ioctls, marked as deprecated by mistake
Fixes:
- fix limit check for number of devices during chunk allocation
- fix a race due to double evaluation of i_size_read inside max()
macro, can cause a crash
- remove wrong device id check in tree-checker"
* tag 'for-5.4-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: un-deprecate ioctls START_SYNC and WAIT_SYNC
btrfs: save i_size to avoid double evaluation of i_size_read in compress_file_range
Btrfs: fix race leading to metadata space leak after task received signal
btrfs: tree-checker: Fix wrong check on max devid
btrfs: Consider system chunk array size for new SYSTEM chunks
Linus Torvalds [Sat, 9 Nov 2019 16:47:03 +0000 (08:47 -0800)]
Merge tag 'linux-watchdog-5.4-rc7' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- cpwd: fix build regression
- pm8916_wdt: fix pretimeout registration flow
- meson: Fix the wrong value of left time
- imx_sc_wdt: Pretimeout should follow SCU firmware format
- bd70528: Add MODULE_ALIAS to allow module auto loading
* tag 'linux-watchdog-5.4-rc7' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: bd70528: Add MODULE_ALIAS to allow module auto loading
watchdog: imx_sc_wdt: Pretimeout should follow SCU firmware format
watchdog: meson: Fix the wrong value of left time
watchdog: pm8916_wdt: fix pretimeout registration flow
watchdog: cpwd: fix build regression
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
Linus Torvalds [Sat, 9 Nov 2019 02:15:55 +0000 (18:15 -0800)]
Merge tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Two NVMe device removal crash fixes, and a compat fixup for for an
ioctl that was introduced in this release (Anton, Charles, Max - via
Keith)
- Missing error path mutex unlock for drbd (Dan)
- cgroup writeback fixup on dead memcg (Tejun)
- blkcg online stats print fix (Tejun)
* tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block:
cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
block: drbd: remove a stray unlock in __drbd_send_protocol()
blkcg: make blkcg_print_stat() print stats only for online blkgs
nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
nvme-rdma: fix a segmentation fault during module unload
David S. Miller [Sat, 9 Nov 2019 00:50:14 +0000 (16:50 -0800)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Magnus Karlsson [Fri, 8 Nov 2019 19:58:10 +0000 (20:58 +0100)]
ixgbe: need_wakeup flag might not be set for Tx
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Magnus Karlsson [Fri, 8 Nov 2019 19:58:09 +0000 (20:58 +0100)]
i40e: need_wakeup flag might not be set for Tx
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Wed, 6 Nov 2019 17:18:23 +0000 (09:18 -0800)]
igb/igc: use ktime accessors for skb->tstamp
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Nicholas Nunley [Tue, 5 Nov 2019 12:22:14 +0000 (04:22 -0800)]
iavf: initialize ITRN registers with correct values
Since commit 92418fb14750 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Colin Ian King [Fri, 1 Nov 2019 14:00:17 +0000 (14:00 +0000)]
ice: fix potential infinite loop because loop counter being too small
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop") Fixes: b36c598c999c ("ice: Updates to Tx scheduler code") Signed-off-by: Colin Ian King <colin.king@canonical.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Manish Chopra [Fri, 8 Nov 2019 10:42:30 +0000 (02:42 -0800)]
qede: fix NULL pointer deref in __qede_remove()
While rebooting the system with SR-IOV vfs enabled leads
to below crash due to recurrence of __qede_remove() on the VF
devices (first from .shutdown() flow of the VF itself and
another from PF's .shutdown() flow executing pci_disable_sriov())
This patch adds a safeguard in __qede_remove() flow to fix this,
so that driver doesn't attempt to remove "already removed" devices.
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 8 Nov 2019 21:42:40 +0000 (13:42 -0800)]
Merge tag 'pwm/for-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fix from Thierry Reding:
"One more fix to keep a reference to the driver's module as long as
there are users of the PWM exposed by the driver"
* tag 'pwm/for-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: bcm-iproc: Prevent unloading the driver module while in use
Peter Zijlstra [Fri, 8 Nov 2019 10:11:52 +0000 (11:11 +0100)]
sched: Fix pick_next_task() vs 'change' pattern race
Commit 67692435c411 ("sched: Rework pick_next_task() slow-path")
inadvertly introduced a race because it changed a previously
unexplored dependency between dropping the rq->lock and
sched_class::put_prev_task().
The comments about dropping rq->lock, in for example
newidle_balance(), only mentions the task being current and ->on_cpu
being set. But when we look at the 'change' pattern (in for example
sched_setnuma()):
if (queued)
dequeue_task(...);
if (running)
put_prev_task(...);
/* change task properties */
if (queued)
enqueue_task(...);
if (running)
set_next_task(...);
It becomes obvious that if we do this after put_prev_task() has
already been called on @p, things go sideways. This is exactly what
the commit in question allows to happen when it does:
prev->sched_class->put_prev_task(rq, prev, rf);
if (!rq->nr_running)
newidle_balance(rq, rf);
The newidle_balance() call will drop rq->lock after we've called
put_prev_task() and that allows the above 'change' pattern to
interleave and mess up the state.
Furthermore, it turns out we lost the RT-pull when we put the last DL
task.
Fix both problems by extracting the balancing from put_prev_task() and
doing a multi-class balance() pass before put_prev_task().
Qais Yousef [Tue, 5 Nov 2019 11:22:12 +0000 (11:22 +0000)]
sched/core: Fix compilation error when cgroup not selected
When cgroup is disabled the following compilation error was hit
kernel/sched/core.c: In function ‘uclamp_update_active_tasks’:
kernel/sched/core.c:1081:23: error: storage size of ‘it’ isn’t known
struct css_task_iter it;
^~
kernel/sched/core.c:1084:2: error: implicit declaration of function ‘css_task_iter_start’; did you mean ‘__sg_page_iter_start’? [-Werror=implicit-function-declaration]
css_task_iter_start(css, 0, &it);
^~~~~~~~~~~~~~~~~~~
__sg_page_iter_start
kernel/sched/core.c:1085:14: error: implicit declaration of function ‘css_task_iter_next’; did you mean ‘__sg_page_iter_next’? [-Werror=implicit-function-declaration]
while ((p = css_task_iter_next(&it))) {
^~~~~~~~~~~~~~~~~~
__sg_page_iter_next
kernel/sched/core.c:1091:2: error: implicit declaration of function ‘css_task_iter_end’; did you mean ‘get_task_cred’? [-Werror=implicit-function-declaration]
css_task_iter_end(&it);
^~~~~~~~~~~~~~~~~
get_task_cred
kernel/sched/core.c:1081:23: warning: unused variable ‘it’ [-Wunused-variable]
struct css_task_iter it;
^~
cc1: some warnings being treated as errors
make[2]: *** [kernel/sched/core.o] Error 1
Fix by protetion uclamp_update_active_tasks() with
CONFIG_UCLAMP_TASK_GROUP
Fixes: babbe170e053 ("sched/uclamp: Update CPU's refcount on TG's clamp changes") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Qais Yousef <qais.yousef@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Cc: Patrick Bellasi <patrick.bellasi@matbug.net> Cc: Mel Gorman <mgorman@suse.de> Cc: Dietmar Eggemann <dietmar.eggemann@arm.com> Cc: Juri Lelli <juri.lelli@redhat.com> Cc: Ben Segall <bsegall@google.com> Link: https://lkml.kernel.org/r/20191105112212.596-1-qais.yousef@arm.com
Tejun Heo [Fri, 8 Nov 2019 20:18:29 +0000 (12:18 -0800)]
cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
cgroup writeback tries to refresh the associated wb immediately if the
current wb is dead. This is to avoid keeping issuing IOs on the stale
wb after memcg - blkcg association has changed (ie. when blkcg got
disabled / enabled higher up in the hierarchy).
Unfortunately, the logic gets triggered spuriously on inodes which are
associated with dead cgroups. When the logic is triggered on dead
cgroups, the attempt fails only after doing quite a bit of work
allocating and initializing a new wb.
While c3aab9a0bd91 ("mm/filemap.c: don't initiate writeback if mapping
has no dirty pages") alleviated the issue significantly as it now only
triggers when the inode has dirty pages. However, the condition can
still be triggered before the inode is switched to a different cgroup
and the logic simply doesn't make sense.
Skip the immediate switching if the associated memcg is dying.
This is a simplified version of the following two patches:
Linus Torvalds [Fri, 8 Nov 2019 20:31:27 +0000 (12:31 -0800)]
Merge tag 'ceph-for-5.4-rc7' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Some late-breaking dentry handling fixes from Al and Jeff, a patch to
further restrict copy_file_range() to avoid potential data corruption
from Luis and a fix for !CONFIG_CEPH_FSCACHE kernels.
Everything but the fscache fix is marked for stable"
* tag 'ceph-for-5.4-rc7' of git://github.com/ceph/ceph-client:
ceph: return -EINVAL if given fsc mount option on kernel w/o support
ceph: don't allow copy_file_range when stripe_count != 1
ceph: don't try to handle hashed dentries in non-O_CREAT atomic_open
ceph: add missing check in d_revalidate snapdir handling
ceph: fix RCU case handling in ceph_d_revalidate()
ceph: fix use-after-free in __ceph_remove_cap()
vsock/virtio: fix sock refcnt holding during the shutdown
The "42f5cda5eaf4" commit rightly set SOCK_DONE on peer shutdown,
but there is an issue if we receive the SHUTDOWN(RDWR) while the
virtio_transport_close_timeout() is scheduled.
In this case, when the timeout fires, the SOCK_DONE is already
set and the virtio_transport_close_timeout() will not call
virtio_transport_reset() and virtio_transport_do_close().
This causes that both sockets remain open and will never be released,
preventing the unloading of [virtio|vhost]_transport modules.
This patch fixes this issue, calling virtio_transport_reset() and
virtio_transport_do_close() when we receive the SHUTDOWN(RDWR)
and there is nothing left to read.
Fixes: 42f5cda5eaf4 ("vsock/virtio: set SOCK_DONE on peer shutdown") Cc: Stephen Barber <smbarber@chromium.org> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 8 Nov 2019 19:37:24 +0000 (11:37 -0800)]
Merge tag 'mac80211-for-net-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three small fixes:
* we hit a failure path bug related to
ieee80211_txq_setup_flows()
* also use kvmalloc() to make that less likely
* fix a timing value shortly after boot (during
INITIAL_JIFFIES)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: ethernet: octeon_mgmt: Account for second possible VLAN header
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.
Fixes: 109cc16526c6d ("ethernet/cavium: use core min/max MTU checking") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 8 Nov 2019 17:48:19 +0000 (09:48 -0800)]
Merge tag 'modules-for-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull modules fix from Jessica Yu:
"Fix `make nsdeps` for modules composed of multiple source files.
Since $mod_source_files was not in quotes in the call to
generate_deps_for_ns(), not all the source files for a module were
being passed to spatch"
* tag 'modules-for-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
scripts/nsdeps: make sure to pass all module source files to spatch
Linus Torvalds [Fri, 8 Nov 2019 17:43:34 +0000 (09:43 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Fix pte_same() to avoid getting stuck on write fault.
This single arm64 fix is a revert of 747a70e60b72 ("arm64: Fix
copy-on-write referencing in HugeTLB"), not because that patch was
wrong, but because it was broken by aa57157be69f ("arm64: Ensure
VM_WRITE|VM_SHARED ptes are clean by default") which we merged in
-rc6.
We spotted the issue in Android (AOSP), where one of the JIT threads
gets stuck on a write fault during boot because the faulting pte is
marked as PTE_DIRTY | PTE_WRITE | PTE_RDONLY and the fault handler
decides that there's nothing to do thanks to pte_same() masking out
PTE_RDONLY.
Thanks to John Stultz for reporting this and testing this so quickly,
and to Steve Capper for confirming that the HugeTLB tests continue to
pass"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Do not mask out PTE_RDONLY in pte_same()
Uwe Kleine-König [Thu, 17 Oct 2019 19:22:18 +0000 (21:22 +0200)]
pwm: bcm-iproc: Prevent unloading the driver module while in use
The owner member of struct pwm_ops must be set to THIS_MODULE to
increase the reference count of the module such that the module cannot
be removed while its code is in use.
Linus Torvalds [Fri, 8 Nov 2019 16:46:49 +0000 (08:46 -0800)]
Merge tag 'xarray-5.4' of git://git.infradead.org/users/willy/linux-dax
Pull XArray fixes from Matthew Wilcox:
"These all fix various bugs, some of which people have tripped over and
some of which have been caught by automatic tools"
* tag 'xarray-5.4' of git://git.infradead.org/users/willy/linux-dax:
idr: Fix idr_alloc_u32 on 32-bit systems
idr: Fix integer overflow in idr_for_each_entry
radix tree: Remove radix_tree_iter_find
idr: Fix idr_get_next_ul race with idr_remove
XArray: Fix xas_next() with a single entry at 0
Linus Torvalds [Fri, 8 Nov 2019 16:17:22 +0000 (08:17 -0800)]
Merge tag 'drm-fixes-2019-11-08' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Weekly fixes for drm: amdgpu has a few but they are pretty scattered
fixes, the fbdev one is a build regression fix that we didn't want to
risk leaving out, otherwise a couple of i915, one radeon and a core
atomic fix.
core:
- add missing documentation for GEM shmem madvise helpers
- Fix for a state dereference in atomic self-refresh helpers
fbdev:
- One compilation fix for c2p fbdev helpers
amdgpu:
- Fix navi14 display issue root cause and revert workaround
- GPU reset scheduler interaction fix
- Fix fan boost on multi-GPU
- Gfx10 and sdma5 fixes for navi
- GFXOFF fix for renoir
- Add navi14 PCI ID
- GPUVM fix for arcturus
radeon:
- Port an SI power fix from amdgpu
i915:
- Fix HPD poll to avoid kworker consuming a lot of cpu cycles.
- Do not use TBT type for non Type-C ports"
* tag 'drm-fixes-2019-11-08' of git://anongit.freedesktop.org/drm/drm:
drm/radeon: fix si_enable_smc_cac() failed issue
drm/amdgpu/renoir: move gfxoff handling into gfx9 module
drm/amdgpu: add warning for GRBM 1-cycle delay issue in gfx9
drm/amdgpu: add dummy read by engines for some GCVM status registers in gfx10
drm/amdgpu: register gpu instance before fan boost feature enablment
drm/amd/swSMU: fix smu workload bit map error
drm/shmem: Add docbook comments for drm_gem_shmem_object madvise fields
drm/amdgpu: add navi14 PCI ID
Revert "drm/amd/display: setting the DIG_MODE to the correct value."
drm/amd/display: Add ENGINE_ID_DIGD condition check for Navi14
drm/amdgpu: dont schedule jobs while in reset
drm/amdgpu/arcturus: properly set BANK_SELECT and FRAGMENT_SIZE
drm/atomic: fix self-refresh helpers crtc state dereference
drm/i915/dp: Do not switch aux to TBT mode for non-TC ports
drm/i915: Avoid HPD poll detect triggering a new detect cycle
fbdev: c2p: Fix link failure on non-inlining
Linus Torvalds [Fri, 8 Nov 2019 16:15:01 +0000 (08:15 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Fixes for various clk driver issues that happened because of code we
merged this merge window.
The Amlogic driver was missing some flags causing rates to be rounded
improperly or clk_set_rate() to fail. The Samsung driver wasn't
freeing everything on error paths and improperly saving/restoring PLL
state across suspend/resume. The at91 driver was calling msleep() too
early when scheduling hadn't started, so we put in place a quick
solution until we can handle this sort of problem in the core
framework.
There were also problems with the Allwinner driver and operator
precedence being incorrect causing subtle bugs. Finally, the TI driver
was duplicating aliases and not delaying long enough leading to some
unexpected timeouts"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: clkctrl: Fix failed to enable error with double udelay timeout
clk: ti: dra7-atl-clock: Remove ti_clk_add_alias call
clk: sunxi-ng: a80: fix the zero'ing of bits 16 and 18
clk: sunxi: Fix operator precedence in sunxi_divs_clk_setup
clk: ast2600: Fix enabling of clocks
clk: at91: avoid sleeping early
clk: imx8m: Use SYS_PLL1_800M as intermediate parent of CLK_ARM
clk: samsung: exynos5420: Preserve PLL configuration during suspend/resume
clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU
clk: samsung: exynos5433: Fix error paths
clk: at91: sam9x60: fix programmable clock
clk: meson: g12a: set CLK_MUX_ROUND_CLOSEST on the cpu clock muxes
clk: meson: g12a: fix cpu clock rate setting
clk: meson: gxbb: let sar_adc_clk_div set the parent clock rate
The max value of EPB can only be 0x0F. Attempting to set more than that
triggers an "unchecked MSR access error" warning which happens in
intel_pstate_hwp_force_min_perf() called via cpufreq stop_cpu().
However, it is not even necessary to touch the EPB from intel_pstate,
because it is restored on every CPU online by the intel_epb.c code,
so let that code do the right thing and drop the redundant (and
incorrect) EPB update from intel_pstate.
Fixes: af3b7379e2d70 ("cpufreq: intel_pstate: Force HWP min perf before offline") Reported-by: Qian Cai <cai@lca.pw> Cc: 5.2+ <stable@vger.kernel.org> # 5.2+ Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ahmed Zaki [Thu, 31 Oct 2019 12:12:43 +0000 (06:12 -0600)]
mac80211: fix station inactive_time shortly after boot
In the first 5 minutes after boot (time of INITIAL_JIFFIES),
ieee80211_sta_last_active() returns zero if last_ack is zero. This
leads to "inactive time" showing jiffies_to_msecs(jiffies).
# iw wlan0 station get fc:ec:da:64:a6:dd
Station fc:ec:da:64:a6:dd (on wlan0)
inactive time: 4294894049 ms
.
.
connected time: 70 seconds
Dave Airlie [Fri, 8 Nov 2019 03:07:58 +0000 (13:07 +1000)]
Merge tag 'drm-fixes-5.4-2019-11-06' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.4-2019-11-06:
amdgpu:
- Fix navi14 display issue root cause and revert workaround
- GPU reset scheduler interaction fix
- Fix fan boost on multi-GPU
- Gfx10 and sdma5 fixes for navi
- GFXOFF fix for renoir
- Add navi14 PCI ID
- GPUVM fix for arcturus
Dave Airlie [Fri, 8 Nov 2019 02:12:49 +0000 (12:12 +1000)]
Merge tag 'drm-misc-fixes-2019-11-07-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- Some new documentation for GEM shmem madvise helpers
- Fix for a state dereference in atomic self-refresh helpers
- One compilation fix for c2p fbdev helpers
David Ahern [Thu, 7 Nov 2019 18:29:52 +0000 (18:29 +0000)]
ipv4: Fix table id reference in fib_sync_down_addr
Hendrik reported routes in the main table using source address are not
removed when the address is removed. The problem is that fib_sync_down_addr
does not account for devices in the default VRF which are associated
with the main table. Fix by updating the table id reference.
Fixes: 5a56a0b3a45d ("net: Don't delete routes in different VRFs") Reported-by: Hendrik Donner <hd@os-cillation.de> Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 7 Nov 2019 17:26:19 +0000 (09:26 -0800)]
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
While looking at a syzbot KCSAN report [1], I found multiple
issues in this code :
1) fib6_nh->last_probe has an initial value of 0.
While probably okay on 64bit kernels, this causes an issue
on 32bit kernels since the time_after(jiffies, 0 + interval)
might be false ~24 days after boot (for HZ=1000)
2) The data-race found by KCSAN
I could use READ_ONCE() and WRITE_ONCE(), but we also can
take the opportunity of not piling-up too many rt6_probe_deferred()
works by using instead cmpxchg() so that only one cpu wins the race.
[1]
BUG: KCSAN: data-race in find_match / find_match
read to 0xffff8880bb7aabe8 of 8 bytes by interrupt on cpu 0:
rt6_probe net/ipv6/route.c:657 [inline]
find_match net/ipv6/route.c:757 [inline]
find_match+0x521/0x790 net/ipv6/route.c:733
__find_rr_leaf+0xe3/0x780 net/ipv6/route.c:831
find_rr_leaf net/ipv6/route.c:852 [inline]
rt6_select net/ipv6/route.c:896 [inline]
fib6_table_lookup+0x383/0x650 net/ipv6/route.c:2164
ip6_pol_route+0xee/0x5c0 net/ipv6/route.c:2200
ip6_pol_route_output+0x48/0x60 net/ipv6/route.c:2452
fib6_rule_lookup+0x3d6/0x470 net/ipv6/fib6_rules.c:117
ip6_route_output_flags_noref+0x16b/0x230 net/ipv6/route.c:2484
ip6_route_output_flags+0x50/0x1a0 net/ipv6/route.c:2497
ip6_dst_lookup_tail+0x25d/0xc30 net/ipv6/ip6_output.c:1049
ip6_dst_lookup_flow+0x68/0x120 net/ipv6/ip6_output.c:1150
inet6_csk_route_socket+0x2f7/0x420 net/ipv6/inet6_connection_sock.c:106
inet6_csk_xmit+0x91/0x1f0 net/ipv6/inet6_connection_sock.c:121
__tcp_transmit_skb+0xe81/0x1d60 net/ipv4/tcp_output.c:1169
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18894 Comm: udevd Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh") Fixes: f547fac624be ("ipv6: rate-limit probes for neighbourless routes") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta [Thu, 7 Nov 2019 17:09:53 +0000 (17:09 +0000)]
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
This patch fixes the problem of the spin locks, originally
meant for the netpoll path of hns driver, causing deadlock in
the normal NAPI poll path. The issue happened due to the presence
of the stray leftover spin lock code related to the netpoll,
whose support was earlier removed from the HNS[1], got activated
due to enabling of NET_POLL_CONTROLLER switch.
Earlier background:
The netpoll handling code originally had this bug(as identified
by Marc Zyngier[2]) of wrong spin lock API being used which did
not disable the interrupts and hence could cause locking issues.
i.e. if the lock were first acquired in context to thread like
'ip' util and this lock if ever got later acquired again in
context to the interrupt context like TX/RX (Interrupts could
always pre-empt the lock holding task and acquire the lock again)
and hence could cause deadlock.
Proposed Solution:
1. If the netpoll was enabled in the HNS driver, which is not
right now, we could have simply used spin_[un]lock_irqsave()
2. But as netpoll is disabled, therefore, it is best to get rid
of the existing locks and stray code for now. This should
solve the problem reported by Marc.
Fixes: 4bd2c03be707 ("net: hns: remove ndo_poll_controller") Cc: lipeng <lipeng321@huawei.com> Cc: Yisen Zhuang <yisen.zhuang@huawei.com> Cc: Eric Dumazet <edumazet@google.com> Cc: David S. Miller <davem@davemloft.net> Reported-by: Marc Zyngier <maz@kernel.org> Acked-by: Marc Zyngier <maz@kernel.org> Tested-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Thu, 7 Nov 2019 08:48:01 +0000 (09:48 +0100)]
CDC-NCM: handle incomplete transfer of MTU
A malicious device may give half an answer when asked
for its MTU. The driver will proceed after this with
a garbage MTU. Anything but a complete answer must be treated
as an error.
V2: used sizeof as request by Alexander
Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pan Bian [Thu, 7 Nov 2019 06:29:50 +0000 (14:29 +0800)]
nfc: netlink: fix double device reference drop
The function nfc_put_device(dev) is called twice to drop the reference
to dev when there is no associated local llcp. Remove one of them to fix
the bug.
Fixes: 52feb444a903 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support") Fixes: d9b8d8e19b07 ("NFC: llcp: Service Name Lookup netlink interface") Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 7 Nov 2019 19:54:54 +0000 (11:54 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
"Two fixes for the HID subsystem:
- regression fix for i2c-hid power management (Hans de Goede)
- signed vs unsigned API fix for Wacom driver (Jason Gerecke)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: wacom: generic: Treat serial number and related fields as unsigned
HID: i2c-hid: Send power-on command after reset
Takashi Iwai [Thu, 7 Nov 2019 12:52:17 +0000 (13:52 +0100)]
Merge tag 'asoc-fix-v5.4-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.4
These are a collection of fixes since v5.4-rc4 that have accumilated,
they're all driver specific and there's nothing major in here so it's
probably not essential to actually send them but I'll leave that call to
you.
Amelie Delaunay [Mon, 4 Nov 2019 10:09:08 +0000 (11:09 +0100)]
pinctrl: stmfx: fix valid_mask init sequence
With stmfx_pinctrl_gpio_init_valid_mask callback, gpio_valid_mask was used
to initialize gpiochip valid_mask for gpiolib. But gpio_valid_mask was not
yet initialized. gpio_valid_mask required gpio-ranges to be registered,
this is the case after gpiochip_add_data call. But init_valid_mask
callback is also called under gpiochip_add_data. gpio_valid_mask
initialization cannot be moved before gpiochip_add_data because
gpio-ranges are not registered.
So, it is not possible to use init_valid_mask callback.
To avoid this issue, get rid of valid_mask and rely on ranges.
Pan Bian [Thu, 7 Nov 2019 01:33:20 +0000 (09:33 +0800)]
NFC: st21nfca: fix double free
The variable nfcid_skb is not changed in the callee nfc_hci_get_param()
if error occurs. Consequently, the freed variable nfcid_skb will be
freed again, resulting in a double free bug. Set nfcid_skb to NULL after
releasing it to fix the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 7 Nov 2019 01:30:19 +0000 (09:30 +0800)]
net: hns3: add compatible handling for command HCLGE_OPC_PF_RST_DONE
Since old firmware does not support HCLGE_OPC_PF_RST_DONE, it will
return -EOPNOTSUPP to the driver when received this command. So
for this case, it should just print a warning and return success
to the caller.
Fixes: 72e2fb07997c ("net: hns3: clear reset interrupt status in hclge_irq_handle()") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 6 Nov 2019 20:51:31 +0000 (21:51 +0100)]
r8169: fix page read in r8168g_mdio_read
Functions like phy_modify_paged() read the current page, on Realtek
PHY's this means reading the value of register 0x1f. Add special
handling for reading this register, similar to what we do already
in r8168g_mdio_write(). Currently we read a random value that by
chance seems to be 0 always.
Fixes: a2928d28643e ("r8169: use paged versions of phylib MDIO access functions") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:04 +0000 (16:03 +0100)]
net: stmmac: Fix TSO descriptor with Enhanced Addressing
When using addressing > 32 bits the TSO first descriptor only has the
header so we can't set the payload field for this descriptor. Let's
reset the variable so that buffer 2 value is zero.
Fixes: a993db88d17d ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:03 +0000 (16:03 +0100)]
net: stmmac: Fix the packet count in stmmac_rx()
Currently, stmmac_rx() is counting the number of descriptors but it
should count the number of packets as specified by the NAPI limit.
Fix this.
Fixes: ec222003bd94 ("net: stmmac: Prepare to add Split Header support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:02 +0000 (16:03 +0100)]
net: stmmac: xgmac: Disable MMC interrupts by default
MMC interrupts were being enabled, which is not what we want because it
will lead to a storm of interrupts that are not handled at all. Fix it
by disabling all MMC interrupts for XGMAC.
Fixes: b6cdf09f51c2 ("net: stmmac: xgmac: Implement MMC counters") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:01 +0000 (16:03 +0100)]
net: stmmac: xgmac: Disable Flow Control when 1 or more queues are in AV
When in AVB mode we need to disable flow control to prevent MAC from
pausing in TX side.
Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:03:00 +0000 (16:03 +0100)]
net: stmmac: xgmac: Fix AV Feature detection
Fix incorrect precedence of operators. For reference: AV implies AV
Feature but RAV implies only RX side AV Feature. As we want full AV
features we need to check RAV.
Fixes: c2b69474d63b ("net: stmmac: xgmac: Correct RAVSEL field interpretation") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:59 +0000 (16:02 +0100)]
net: stmmac: xgmac: Fix TSA selection
When we change between Transmission Scheduling Algorithms, we need to
clear previous values so that the new chosen algorithm is correctly
selected.
Fixes: ec6ea8e3eee9 ("net: stmmac: Add CBS support in XGMAC2") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:58 +0000 (16:02 +0100)]
net: stmmac: xgmac: Only get SPH header len if available
Split Header length is only available when L34T == 0. Fix this by
correctly checking if L34T is zero before trying to get Header length.
Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:57 +0000 (16:02 +0100)]
net: stmmac: selftests: Prevent false positives in filter tests
In L2 tests that filter packets by destination MAC address we need to
prevent false positives that can occur if we add an address that
collides with the existing ones.
To fix this, lets manually check if the new address to be added is
already present in the NIC and use a different one if so. For Hash
filtering this also envolves converting the address to the hash.
Fixes: 091810dbded9 ("net: stmmac: Introduce selftests support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:56 +0000 (16:02 +0100)]
net: stmmac: xgmac: bitrev32 returns u32
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 0efedbf11f07 ("net: stmmac: xgmac: Fix XGMAC selftests") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 6 Nov 2019 15:02:55 +0000 (16:02 +0100)]
net: stmmac: gmac4: bitrev32 returns u32
The bitrev32 function returns an u32 var, not an int. Fix it.
Fixes: 477286b53f55 ("stmmac: add GMAC4 core support") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Shilovsky [Wed, 6 Nov 2019 21:58:15 +0000 (13:58 -0800)]
SMB3: Fix persistent handles reconnect
When the client hits a network reconnect, it re-opens every open
file with a create context to reconnect a persistent handle. All
create context types should be 8-bytes aligned but the padding
was missed for that one. As a result, some servers don't allow
us to reconnect handles and return an error. The problem occurs
when the problematic context is not at the end of the create
request packet. Fix this by adding a proper padding at the end
of the reconnect persistent handle context.
Cc: Stable <stable@vger.kernel.org> # 4.19.x Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
changzhu [Tue, 5 Nov 2019 10:29:12 +0000 (18:29 +0800)]
drm/amdgpu: add warning for GRBM 1-cycle delay issue in gfx9
It needs to add warning to update firmware in gfx9
in case that firmware is too old to have function to
realize dummy read in cp firmware.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
changzhu [Thu, 10 Oct 2019 03:02:33 +0000 (11:02 +0800)]
drm/amdgpu: add dummy read by engines for some GCVM status registers in gfx10
The GRBM register interface is now capable of bursting 1 cycle per
register wr->wr, wr->rd much faster than previous muticycle per
transaction done interface. This has caused a problem where
status registers requiring HW to update have a 1 cycle delay, due
to the register update having to go through GRBM.
For cp ucode, it has realized dummy read in cp firmware.It covers
the use of WAIT_REG_MEM operation 1 case only.So it needs to call
gfx_v10_0_wait_reg_mem in gfx10. Besides it also needs to add warning to
update firmware in case firmware is too old to have function to realize
dummy read in cp firmware.
For sdma ucode, it hasn't realized dummy read in sdma firmware. sdma is
moved to gfxhub in gfx10. So it needs to add dummy read in driver
between amdgpu_ring_emit_wreg and amdgpu_ring_emit_reg_wait for sdma_v5_0.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Tue, 5 Nov 2019 10:13:49 +0000 (18:13 +0800)]
drm/amdgpu: register gpu instance before fan boost feature enablment
Otherwise, the feature enablement will be skipped due to wrong count.
Fixes: beff74bc6e0fa91 ("drm/amdgpu: fix a race in GPU reset with IB test (v2)") Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kevin Wang [Tue, 5 Nov 2019 10:16:38 +0000 (18:16 +0800)]
drm/amd/swSMU: fix smu workload bit map error
fix workload bit (WORKLOAD_PPLIB_COMPUTE_BIT) map error
on vega20 and navi asic.
fix commit:
drm/amd/powerplay: add function get_workload_type_map for swsmu
Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Kenneth Feng <kenneth.feng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ursula Braun [Wed, 6 Nov 2019 09:49:57 +0000 (10:49 +0100)]
net/smc: fix ethernet interface refcounting
If a pnet table entry is to be added mentioning a valid ethernet
interface, but an invalid infiniband or ISM device, the dev_put()
operation for the ethernet interface is called twice, resulting
in a negative refcount for the ethernet interface, which disables
removal of such a network interface.
This patch removes one of the dev_put() calls.
Fixes: 890a2cb4a966 ("net/smc: rework pnet table") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 7 Nov 2019 01:33:32 +0000 (17:33 -0800)]
Merge branch 'net-tls-add-a-TX-lock'
Jakub Kicinski says:
====================
net/tls: add a TX lock
Some time ago Pooja and Mallesham started reporting crashes with
an async accelerator. After trying to poke the existing logic into
shape I came to the conclusion that it can't be trusted, and to
preserve our sanity we should just add a lock around the TX side.
First patch removes the sk_write_pending checks from the write
space callbacks. Those don't seem to have a logical justification.
Patch 2 adds the TX lock and patch 3 associated test (which should
hang with current net).
Mallesham reports that even with these fixes applied the async
accelerator workload still occasionally hangs waiting for socket
memory. I suspect that's strictly related to the way async crypto
is integrated in TLS, so I think we should get these into net or
net-next and move from there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 5 Nov 2019 22:24:36 +0000 (14:24 -0800)]
selftests/tls: add test for concurrent recv and send
Add a test which spawns 16 threads and performs concurrent
send and recv calls on the same socket.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 5 Nov 2019 22:24:35 +0000 (14:24 -0800)]
net/tls: add a TX lock
TLS TX needs to release and re-acquire the socket lock if send buffer
fills up.
TLS SW TX path currently depends on only allowing one thread to enter
the function by the abuse of sk_write_pending. If another writer is
already waiting for memory no new ones are allowed in.
This has two problems:
- writers don't wake other threads up when they leave the kernel;
meaning that this scheme works for single extra thread (second
application thread or delayed work) because memory becoming
available will send a wake up request, but as Mallesham and
Pooja report with larger number of threads it leads to threads
being put to sleep indefinitely;
- the delayed work does not get _scheduled_ but it may _run_ when
other writers are present leading to crashes as writers don't
expect state to change under their feet (same records get pushed
and freed multiple times); it's hard to reliably bail from the
work, however, because the mere presence of a writer does not
guarantee that the writer will push pending records before exiting.
Ensuring wakeups always happen will make the code basically open
code a mutex. Just use a mutex.
The TLS HW TX path does not have any locking (not even the
sk_write_pending hack), yet it uses a per-socket sg_tx_data
array to push records.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance") Reported-by: Mallesham Jatharakonda <mallesh537@gmail.com> Reported-by: Pooja Trivedi <poojatrivedi@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 5 Nov 2019 22:24:34 +0000 (14:24 -0800)]
net/tls: don't pay attention to sk_write_pending when pushing partial records
sk_write_pending being not zero does not guarantee that partial
record will be pushed. If the thread waiting for memory times out
the pending record may get stuck.
In case of tls_device there is no path where parial record is
set and writer present in the first place. Partial record is
set only in tls_push_sg() and tls_push_sg() will return an
error immediately. All tls_device callers of tls_push_sg()
will return (and not wait for memory) if it failed.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tejun Heo [Tue, 5 Nov 2019 16:09:51 +0000 (08:09 -0800)]
blkcg: make blkcg_print_stat() print stats only for online blkgs
blkcg_print_stat() iterates blkgs under RCU and doesn't test whether
the blkg is online. This can call into pd_stat_fn() on a pd which is
still being initialized leading to an oops.
The heaviest operation - recursively summing up rwstat counters - is
already done while holding the queue_lock. Expand queue_lock to cover
the other operations and skip the blkg if it isn't online yet. The
online state is protected by both blkcg and queue locks, so this
guarantees that only online blkgs are processed.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Roman Gushchin <guro@fb.com> Cc: Josef Bacik <jbacik@fb.com> Fixes: 903d23f0a354 ("blk-cgroup: allow controllers to output their own stats") Cc: stable@vger.kernel.org # v4.19+ Signed-off-by: Jens Axboe <axboe@kernel.dk>
Rob Herring [Fri, 1 Nov 2019 15:37:54 +0000 (10:37 -0500)]
drm/shmem: Add docbook comments for drm_gem_shmem_object madvise fields
Add missing docbook comments to madvise fields in struct
drm_gem_shmem_object which fixes these warnings:
include/drm/drm_gem_shmem_helper.h:87: warning: Function parameter or member 'madv' not described in 'drm_gem_shmem_object'
include/drm/drm_gem_shmem_helper.h:87: warning: Function parameter or member 'madv_list' not described in 'drm_gem_shmem_object'
Fixes: 17acb9f35ed7 ("drm/shmem: Add madvise state and purge helpers") Reported-by: Sean Paul <sean@poorly.run> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Sean Paul <sean@poorly.run> Link: https://patchwork.freedesktop.org/patch/msgid/20191101153754.22803-1-robh@kernel.org
Vladimir Oltean [Tue, 5 Nov 2019 22:01:40 +0000 (00:01 +0200)]
net: mscc: ocelot: fix __ocelot_rmw_ix prototype
The "read-modify-write register index" function is declared with a
confusing prototype: the "mask" and "reg" arguments are swapped.
Fortunately, this does not affect callers so far. Both arguments are
u32, and the wrapper macros (ocelot_rmw_ix etc) have the arguments in
the correct order (the one from ocelot_io.c).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 6 Nov 2019 23:16:17 +0000 (15:16 -0800)]
Merge branch 'Bonding-fixes-for-Ocelot-switch'
Vladimir Oltean says:
====================
Bonding fixes for Ocelot switch
This series fixes 2 issues with bonding in a system that integrates the
ocelot driver, but the ports that are bonded do not actually belong to
ocelot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil [Tue, 5 Nov 2019 21:50:13 +0000 (23:50 +0200)]
net: mscc: ocelot: don't handle netdev events for other netdevs
The check that the event is actually for this device should be moved
from the "port" handler to the net device handler.
Otherwise the port handler will deny bonding configuration for other
net devices in the same system (like enetc in the LS1028A) that don't
have the lag_upper_info->tx_type restriction that ocelot has.
Fixes: dc96ee3730fc ("net: mscc: ocelot: add bonding support") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmytro Linkin [Tue, 29 Oct 2019 09:44:24 +0000 (11:44 +0200)]
net/mlx5e: Use correct enum to determine uplink port
For vlan push action, if eswitch flow source capability is enabled, flow
source value compared with MLX5_VPORT_UPLINK enum, to determine uplink
port. This lead to syndrome in dmesg if try to add vlan push action.
For example:
$ tc filter add dev vxlan0 ingress protocol ip prio 1 flower \
enc_dst_port 4789 \
action tunnel_key unset pipe \
action vlan push id 20 pipe \
action mirred egress redirect dev ens1f0_0
$ dmesg
...
[ 2456.883693] mlx5_core 0000:82:00.0: mlx5_cmd_check:756:(pid 5273): SET_FLOW_TABLE_ENTRY(0x936) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0xa9c090)
Use the correct enum value MLX5_FLOW_CONTEXT_FLOW_SOURCE_UPLINK.
Fixes: bb204dcf39fe ("net/mlx5e: Determine source port properly for vlan push action") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Jason Gerecke [Wed, 6 Nov 2019 19:59:46 +0000 (11:59 -0800)]
HID: wacom: generic: Treat serial number and related fields as unsigned
The HID descriptors for most Wacom devices oddly declare the serial
number and other related fields as signed integers. When these numbers
are ingested by the HID subsystem, they are automatically sign-extended
into 32-bit integers. We treat the fields as unsigned elsewhere in the
kernel and userspace, however, so this sign-extension causes problems.
In particular, the sign-extended tool ID sent to userspace as ABS_MISC
does not properly match unsigned IDs used by xf86-input-wacom and libwacom.
We introduce a function 'wacom_s32tou' that can undo the automatic sign
extension performed by 'hid_snto32'. We call this function when processing
the serial number and related fields to ensure that we are dealing with
and reporting the unsigned form. We opt to use this method rather than
adding a descriptor fixup in 'wacom_hid_usage_quirk' since it should be
more robust in the face of future devices.
Ref: https://github.com/linuxwacom/input-wacom/issues/134 Fixes: f85c9dc678 ("HID: wacom: generic: Support tool ID and additional tool types") CC: <stable@vger.kernel.org> # v4.10+ Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Reviewed-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Zhan Liu [Sat, 2 Nov 2019 01:10:17 +0000 (21:10 -0400)]
drm/amd/display: Add ENGINE_ID_DIGD condition check for Navi14
[Why]
Navi10 has 6 PHY, but Navi14 only has 5 PHY, that is
because there is no ENGINE_ID_DIGD in Navi14. Without
this patch, many HDMI related issues (e.g. HDMI S3
resume failure, HDMI pink screen on boot) will be
observed.
[How]
If "eng_id" is larger than ENGINE_ID_DIGD, then
add "eng_id" by 1.
Signed-off-by: Zhan Liu <zhan.liu@amd.com> Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / kernel.git / log