Jonathan reported that this commit broke this topology, where all the space
available on bus 02 was assigned to the 02:00.0 bridge window, leaving none
for the e1000 device at 02:00.1:
pci 0000:00:04.0: bridge window [mem 0x10200000-0x103fffff] to [bus 02-04]
pci 0000:02:00.0: bridge window [mem 0x10200000-0x103fffff] to [bus 03-04]
pci 0000:02:00.1: BAR 0: failed to assign [mem size 0x00020000]
e1000 0000:02:00.1: can't ioremap BAR 0: [??? 0x00000000 flags 0x0]
Linus Torvalds [Tue, 11 Oct 2022 18:08:18 +0000 (11:08 -0700)]
Merge tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better.
- Revert to a BAR assignment inherited from firmware only when the
address is actually reachable via any upstream bridges, which fixes
some cases where firmware doesn't configure all devices.
- Add a sysfs interface to resize BARs so this can be done before
assigning devices to a VM through VFIO.
Power management:
- Disable Precision Time Management for all devices on suspend to
enable lower-power PM state. We previously did this just for Root
Ports, which isn't enough because downstream devices can still
generate PTM messages, which cause errors if it's disabled in the
Root Port.
- Save and restore the ASPM L1 PM Substates configuration for
suspend/ resume. Previously this configuration was lost, so L1.x
states likely stopped working after resume.
- Check whether the L1 PM Substates Capability exists. If it didn't
exist, we previously read junk and tried to configure L1 Substates
based on that.
- Fix the LTR_L1.2_THRESHOLD computation, which previously set a
threshold for entering L1.2 that was too low in some cases.
- Reduce the delay after transitions to or from D3cold by using
usleep_range() rather than msleep(), which often slept for ~19ms
instead of the 10ms normally required. The spec says 10ms is
enough, but it's possible we could trip over devices that need a
little more.
Error handling:
- Work around a BIOS bug that caused Intel Root Ports to advertise a
Root Port Programmed I/O (RP PIO) log size of zero, which caused
annoying warnings and prevented the kernel from dumping log
registers for DPC errors.
Qualcomm PCIe controller driver:
- Add support for SC8280XP and SA8540P host controllers and SM8450
endpoint controller.
- Disable Master AXI clock on endpoint controllers to save power when
link is idle or in L1.x.
- Expose link state transition counts via debugfs to help debug
issues with low-power states.
- Add auto-loading module support.
Synopsys DesignWare PCIe controller driver:
- Remove a dependency on ZONE_DMA32 by allocating the MSI target page
differently. There's more work to do related to eDMA controllers,
so it's not completely settled"
* tag 'pci-v6.1-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (71 commits)
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: Expose PCIe Resizable BAR support via sysfs
PCI/ASPM: Correct LTR_L1.2_THRESHOLD computation
PCI/ASPM: Ignore L1 PM Substates if device lacks capability
PCI/ASPM: Factor out L1 PM Substates configuration
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI/ASPM: Refactor L1 PM Substates Control Register programming
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
phy: freescale: imx8m-pcie: Fix the wrong order of phy_init() and phy_power_on()
...
Linus Torvalds [Tue, 11 Oct 2022 18:03:42 +0000 (11:03 -0700)]
Merge tag 'i2c-for-6.1-rc1-batch2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
- correct a variable type in the new pci1xxxx driver
- add a new SoC to the qcom-cci driver
- fix an issue with the designware driver which now got enough testing
- the aspeed driver now handles busy target backends better
* tag 'i2c-for-6.1-rc1-batch2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: aspeed: Assert NAK when slave is busy
i2c: designware: Fix handling of real but unexpected device interrupts
i2c: qcom-cci: Add MSM8226 compatible
dt-bindings: i2c: qcom,i2c-cci: Document clocks for MSM8974
dt-bindings: i2c: qcom,i2c-cci: Document MSM8226 compatible
i2c: microchip: pci1xxxx: Fix comparison of -EPERM against an unsigned variable
Linus Torvalds [Tue, 11 Oct 2022 17:53:25 +0000 (10:53 -0700)]
Merge tag 'input-for-v6.1-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for IBM Operational Panel
- a new driver for PinePhone keyboards
- RT5120 PMIC power key support
- various enhancements and support for new models in xpad (Xbox) driver
- a new compatible ID for Elan touchscreen driver
- rework of adp5588-keys driver to support configuring via device
properties (OF, ACPI, etc) instead of platform data, and proper
support of optional gpiochip functionality (and removal of
gpio-adp5588 driver)
- improvements to firmware update handling in Synaptics RMI4 driver
- support for double key matrix in mt6779-keypad
- support for polled mode in adc-joystick driver
- other assorted driver fixes, cleanups and improvements
* tag 'input-for-v6.1-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (90 commits)
Input: i8042 - fix refount leak on sparc
Input: i8042 - add LoongArch support in i8042-acpipnpio.h
Input: i8042 - rename i8042-x86ia64io.h to i8042-acpipnpio.h
Input: pinephone-keyboard - support the proxied I2C bus
Input: pinephone-keyboard - add PinePhone keyboard driver
dt-bindings: input: Add the PinePhone keyboard binding
dt-bindings: input: Convert hid-over-i2c to DT schema
input: drop empty comment blocks
Input: xpad - add X-Box Adaptive Profile button
Input: add ABS_PROFILE to uapi and documentation
Input: xpad - add X-Box Adaptive XBox button
Input: xpad - add X-Box Adaptive support
Input: ims-pcu - fix spelling mistake "BOOLTLOADER" -> "BOOTLOADER"
Input: ibm-panel - add missing MODULE_DEVICE_TABLE
Input: icn8505 - utilize acpi_get_subsystem_id()
Input: xpad - decipher xpadone packages with GIP defines
Input: xpad - refactor using BIT() macro
Input: synaptics-rmi4 - convert to use sysfs_emit() APIs
Input: twl4030-pwrbutton - add missing of.h include
Input: applespi - replace zero-length array with DECLARE_FLEX_ARRAY() helper
...
Linus Torvalds [Tue, 11 Oct 2022 17:49:17 +0000 (10:49 -0700)]
Merge tag 'fbdev-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev updates from Helge Deller:
"Here's a fix for the smscufx USB graphics card to prevent a kernel
crash if it's plugged in/out too fast.
The other patches are mostly small cleanups, fixes in failure paths
and code removal:
- fix an use-after-free in smscufx USB graphics driver
- add missing pci_disable_device() in tridentfb failure paths
- correctly handle irq detection failure in mb862xx driver
- fix resume code in omapfb/dss
- drop unused code in controlfb, tridentfb, arkfb, imxfb and udlfb
- convert uvesafb to use scnprintf() instead of snprintf()
- convert gbefb to use dev_groups
- add MODULE_DEVICE_TABLE() entry to vga16fb"
* tag 'fbdev-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: mb862xx: Fix check of return value from irq_of_parse_and_map()
fbdev: vga16fb: Add missing MODULE_DEVICE_TABLE() entry
fbdev: tridentfb: Fix missing pci_disable_device() in probe and remove
fbdev: smscufx: Fix use-after-free in ufx_ops_open()
fbdev: gbefb: Convert to use dev_groups
fbdev: imxfb: Remove redundant dev_err() call
fbdev: omapfb/dss: Use pm_runtime_resume_and_get() instead of pm_runtime_get_sync()
fbdev: uvesafb: Convert snprintf to scnprintf
fbdev: arkfb: Remove the unused function dac_read_reg()
fbdev: tridentfb: Remove the unused function shadowmode_off()
fbdev: controlfb: Remove the unused function VAR_MATCH()
fbdev: udlfb: Remove redundant initialization to variable identical
Linus Torvalds [Tue, 11 Oct 2022 17:42:25 +0000 (10:42 -0700)]
Merge tag 'for-linus-6.1-1' of https://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Fix a bunch of little problems in IPMI
This is mostly just doc, config, and little tweaks. Nothing big, which
is why there was nothing for 6.0. There is one crash fix, but it's not
something that I think anyone is using yet"
* tag 'for-linus-6.1-1' of https://github.com/cminyard/linux-ipmi:
ipmi: Remove unused struct watcher_entry
ipmi: kcs: aspeed: Update port address comments
ipmi: Add __init/__exit annotations to module init/exit funcs
ipmi:ipmb: Don't call ipmi_unregister_smi() on a register failure
ipmi:ipmb: Fix a vague comment and a typo
dt-binding: ipmi: add fallback to npcm845 compatible
ipmi: Fix comment typo
char: ipmi: modify NPCM KCS configuration
dt-bindings: ipmi: Add npcm845 compatible
Lukas Bulwahn [Tue, 4 Oct 2022 07:13:02 +0000 (09:13 +0200)]
alpha: remove the needless aliases osf_{readv,writev}
Commit 025845a42e1a ("a.out: Remove the a.out implementation") removes
CONFIG_OSF4_COMPAT and its functionality. Hence, sys_osf_{readv,writev}
are now just aliases of sys_{readv,writev}.
Remove these needless aliases.
[ Identical patch also posted by Jason A. Donenfeld ]
Joel Stanley [Tue, 11 Oct 2022 03:59:10 +0000 (14:29 +1030)]
powerpc: Fix 85xx build
The merge of the kbuild tree dropped the renaming of the FSL_BOOKE
kconfig option.
Fixes: 61fbd5914e7f ("Merge tag 'kbuild-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild") Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 11 Oct 2022 03:32:10 +0000 (20:32 -0700)]
Merge tag 'xfs-6.1-for-linus' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs updates from Dave Chinner:
"There are relatively few updates this cycle; half the cycle was eaten
by a grue, the other half was eaten by a tricky data corruption issue
that I still haven't entirely solved.
Hence there's no major changes in this cycle and it's largely just
minor cleanups and small bug fixes:
- fixes for filesystem shutdown procedure during a DAX memory failure
notification
- bug fixes
- logic cleanups
- log message cleanups
- updates to use vfs{g,u}id_t helpers where appropriate"
* tag 'xfs-6.1-for-linus' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: on memory failure, only shut down fs after scanning all mappings
xfs: rearrange the logic and remove the broken comment for xfs_dir2_isxx
xfs: trim the mapp array accordingly in xfs_da_grow_inode_int
xfs: do not need to check return value of xlog_kvmalloc()
xfs: port to vfs{g,u}id_t and associated helpers
xfs: remove xfs_setattr_time() declaration
xfs: Remove the unneeded result variable
xfs: missing space in xfs trace log
xfs: simplify if-else condition in xfs_reflink_trim_around_shared
xfs: simplify if-else condition in xfs_validate_new_dalign
xfs: replace unnecessary seq_printf with seq_puts
xfs: clean up "%Ld/%Lu" which doesn't meet C standard
xfs: remove redundant else for clean code
xfs: remove the redundant word in comment
Linus Torvalds [Tue, 11 Oct 2022 03:28:41 +0000 (20:28 -0700)]
Merge tag 'f2fs-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This round looks fairly small comparing to the previous updates and
includes mostly minor bug fixes. Nevertheless, as we've still
interested in improving the stability, Chao added some debugging
methods to diagnoze subtle runtime inconsistency problem.
Enhancements:
- store all the corruption or failure reasons in superblock
- detect meta inode, summary info, and block address inconsistency
- increase the limit for reserve_root for low-end devices
- add the number of compressed IO in iostat
Bug fixes:
- DIO write fix for zoned devices
- do out-of-place writes for cold files
- fix some stat updates (FS_CP_DATA_IO, dirty page count)
- fix race condition on setting FI_NO_EXTENT flag
- fix data races when freezing super
- fix wrong continue condition check in GC
- do not allow ATGC for LFS mode
In addition, there're some code enhancement and clean-ups as usual"
* tag 'f2fs-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (32 commits)
f2fs: change to use atomic_t type form sbi.atomic_files
f2fs: account swapfile inodes
f2fs: allow direct read for zoned device
f2fs: support recording errors into superblock
f2fs: support recording stop_checkpoint reason into super_block
f2fs: remove the unnecessary check in f2fs_xattr_fiemap
f2fs: introduce cp_status sysfs entry
f2fs: fix to detect corrupted meta ino
f2fs: fix to account FS_CP_DATA_IO correctly
f2fs: code clean and fix a type error
f2fs: add "c_len" into trace_f2fs_update_extent_tree_range for compressed file
f2fs: fix to do sanity check on summary info
f2fs: port to vfs{g,u}id_t and associated helpers
f2fs: fix to do sanity check on destination blkaddr during recovery
f2fs: let FI_OPU_WRITE override FADVISE_COLD_BIT
f2fs: fix race condition on setting FI_NO_EXTENT flag
f2fs: remove redundant check in f2fs_sanity_check_cluster
f2fs: add static init_idisk_time function to reduce the code
f2fs: fix typo
f2fs: fix wrong dirty page count when race between mmap and fallocate.
...
Linus Torvalds [Tue, 11 Oct 2022 03:21:09 +0000 (20:21 -0700)]
Merge tag '9p-for-6.1' of https://github.com/martinetd/linux
Pull 9p updates from Dominique Martinet:
"Smaller buffers for small messages and fixes.
The highlight of this is Christian's patch to allocate smaller buffers
for most metadata requests: 9p with a big msize would try to allocate
large buffers when just 4 or 8k would be more than enough; this brings
in nice performance improvements.
There's also a few fixes for problems reported by syzkaller (thanks to
Schspa Shi, Tetsuo Handa for tests and feedback/patches) as well as
some minor cleanup"
* tag '9p-for-6.1' of https://github.com/martinetd/linux:
net/9p: clarify trans_fd parse_opt failure handling
net/9p: add __init/__exit annotations to module init/exit funcs
net/9p: use a dedicated spinlock for trans_fd
9p/trans_fd: always use O_NONBLOCK read/write
net/9p: allocate appropriate reduced message buffers
net/9p: add 'pooled_rbuffers' flag to struct p9_trans_module
net/9p: add p9_msg_buf_size()
9p: add P9_ERRMAX for 9p2000 and 9p2000.u
net/9p: split message size argument into 't_size' and 'r_size' pair
9p: trans_fd/p9_conn_cancel: drop client lock earlier
Linus Torvalds [Tue, 11 Oct 2022 03:13:22 +0000 (20:13 -0700)]
Merge tag 'gfs2-nopid-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 debugfs updates from Andreas Gruenbacher:
- Improve the way how the state of glocks is reported in debugfs for
glocks which are not held by processes, but rather by other resouces
like cached inodes or flocks.
* tag 'gfs2-nopid-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Mark the remaining process-independent glock holders as GL_NOPID
gfs2: Mark flock glock holders as GL_NOPID
gfs2: Add GL_NOPID flag for process-independent glock holders
gfs2: Add flocks to glockfd debugfs file
gfs2: Add glockfd debugfs file
Linus Torvalds [Tue, 11 Oct 2022 03:08:52 +0000 (20:08 -0700)]
Merge tag 'gfs2-v6.0-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull gfs2 updates from Andreas Gruenbacher:
- Make sure to initialize the filesystem work queues before registering
the filesystem; this prevents them from being used uninitialized.
- On filesystem withdraw: prevent a a double iput() and immediately
reject pending locking requests that can no longer succeed.
- Use TRY lock in gfs2_inode_lookup() to prevent a rare glock hang
during evict.
- During filesystem mount, explicitly make sure that the sb_bsize and
sb_bsize_shift super block fields are consistent with each other.
This prevents messy error messages during fuzz testing.
- Switch from strlcpy to strscpy.
* tag 'gfs2-v6.0-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: Register fs after creating workqueues
gfs2: Check sb_bsize_shift after reading superblock
gfs2: Switch from strlcpy to strscpy
gfs2: Clear flags when withdraw prevents xmote
gfs2: Dequeue waiters when withdrawn
gfs2: Prevent double iput for journal on error
gfs2: Use TRY lock in gfs2_inode_lookup for UNLINKED inodes
Linus Torvalds [Tue, 11 Oct 2022 03:04:22 +0000 (20:04 -0700)]
Merge tag '6.1-rc-smb3-client-fixes-part1' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs updates from Steve French:
- data corruption fix when cache disabled
- four RDMA (smbdirect) improvements, including enabling support for
SoftiWARP
- four signing improvements
- three directory lease improvements
- four cleanup fixes
- minor security fix
- two debugging improvements
* tag '6.1-rc-smb3-client-fixes-part1' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
smb3: fix oops in calculating shash_setkey
cifs: secmech: use shash_desc directly, remove sdesc
smb3: rename encryption/decryption TFMs
cifs: replace kfree() with kfree_sensitive() for sensitive data
cifs: remove initialization value
cifs: Replace a couple of one-element arrays with flexible-array members
smb3: do not log confusing message when server returns no network interfaces
smb3: define missing create contexts
cifs: store a pointer to a fid in the cfid structure instead of the struct
cifs: improve handlecaching
cifs: Make tcon contain a wrapper structure cached_fids instead of cached_fid
smb3: add dynamic trace points for tree disconnect
Fix formatting of client smbdirect RDMA logging
Handle variable number of SGEs in client smbdirect send.
Reduce client smbdirect max receive segment size
Decrease the number of SMB3 smbdirect client SGEs
cifs: Fix the error length of VALIDATE_NEGOTIATE_INFO message
cifs: destage dirty pages before re-reading them for cache=none
cifs: return correct error in ->calc_signature()
MAINTAINERS: Add Tom Talpey as cifs.ko reviewer
...
Linus Torvalds [Tue, 11 Oct 2022 02:58:04 +0000 (19:58 -0700)]
Merge tag 'nfsd-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull more nfsd updates from Chuck Lever:
- filecache code clean-ups
* tag 'nfsd-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: rework hashtable handling in nfsd_do_file_acquire
nfsd: fix nfsd_file_unhash_and_dispose
Linus Torvalds [Tue, 11 Oct 2022 02:45:17 +0000 (19:45 -0700)]
Merge tag 'pull-tmpfile' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs tmpfile updates from Al Viro:
"Miklos' ->tmpfile() signature change; pass an unopened struct file to
it, let it open the damn thing. Allows to add tmpfile support to FUSE"
* tag 'pull-tmpfile' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fuse: implement ->tmpfile()
vfs: open inside ->tmpfile()
vfs: move open right after ->tmpfile()
vfs: make vfs_tmpfile() static
ovl: use vfs_tmpfile_open() helper
cachefiles: use vfs_tmpfile_open() helper
cachefiles: only pass inode to *mark_inode_inuse() helpers
cachefiles: tmpfile error handling cleanup
hugetlbfs: cleanup mknod and tmpfile
vfs: add vfs_tmpfile_open() helper
Linus Torvalds [Tue, 11 Oct 2022 00:53:04 +0000 (17:53 -0700)]
Merge tag 'mm-stable-2022-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull MM updates from Andrew Morton:
- Yu Zhao's Multi-Gen LRU patches are here. They've been under test in
linux-next for a couple of months without, to my knowledge, any
negative reports (or any positive ones, come to that).
- Also the Maple Tree from Liam Howlett. An overlapping range-based
tree for vmas. It it apparently slightly more efficient in its own
right, but is mainly targeted at enabling work to reduce mmap_lock
contention.
Liam has identified a number of other tree users in the kernel which
could be beneficially onverted to mapletrees.
Yu Zhao has identified a hard-to-hit but "easy to fix" lockdep splat
at [1]. This has yet to be addressed due to Liam's unfortunately
timed vacation. He is now back and we'll get this fixed up.
- Dmitry Vyukov introduces KMSAN: the Kernel Memory Sanitizer. It uses
clang-generated instrumentation to detect used-unintialized bugs down
to the single bit level.
KMSAN keeps finding bugs. New ones, as well as the legacy ones.
- Yang Shi adds a userspace mechanism (madvise) to induce a collapse of
memory into THPs.
- Zach O'Keefe has expanded Yang Shi's madvise(MADV_COLLAPSE) to
support file/shmem-backed pages.
- userfaultfd updates from Axel Rasmussen
- zsmalloc cleanups from Alexey Romanov
- cleanups from Miaohe Lin: vmscan, hugetlb_cgroup, hugetlb and
memory-failure
- Huang Ying adds enhancements to NUMA balancing memory tiering mode's
page promotion, with a new way of detecting hot pages.
- memcg updates from Shakeel Butt: charging optimizations and reduced
memory consumption.
- memcg cleanups from Kairui Song.
- memcg fixes and cleanups from Johannes Weiner.
- Vishal Moola provides more folio conversions
- Zhang Yi removed ll_rw_block() :(
- migration enhancements from Peter Xu
- migration error-path bugfixes from Huang Ying
- Aneesh Kumar added ability for a device driver to alter the memory
tiering promotion paths. For optimizations by PMEM drivers, DRM
drivers, etc.
- Mike Kravetz fixes locking issues in hugetlbfs and in hugetlb core.
Link: https://lkml.kernel.org/r/CAOUHufZabH85CeUN-MEMgL8gJGzJEWUrkiM58JkTbBhh-jew0Q@mail.gmail.com
* tag 'mm-stable-2022-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (555 commits)
hugetlb: allocate vma lock for all sharable vmas
hugetlb: take hugetlb vma_lock when clearing vma_lock->vma pointer
hugetlb: fix vma lock handling during split vma and range unmapping
mglru: mm/vmscan.c: fix imprecise comments
mm/mglru: don't sync disk for each aging cycle
mm: memcontrol: drop dead CONFIG_MEMCG_SWAP config symbol
mm: memcontrol: use do_memsw_account() in a few more places
mm: memcontrol: deprecate swapaccounting=0 mode
mm: memcontrol: don't allocate cgroup swap arrays when memcg is disabled
mm/secretmem: remove reduntant return value
mm/hugetlb: add available_huge_pages() func
mm: remove unused inline functions from include/linux/mm_inline.h
selftests/vm: add selftest for MADV_COLLAPSE of uffd-minor memory
selftests/vm: add file/shmem MADV_COLLAPSE selftest for cleared pmd
selftests/vm: add thp collapse shmem testing
selftests/vm: add thp collapse file and tmpfs testing
selftests/vm: modularize thp collapse memory operations
selftests/vm: dedup THP helpers
mm/khugepaged: add tracepoint to hpage_collapse_scan_file()
mm/madvise: add file and shmem support to MADV_COLLAPSE
...
Linus Torvalds [Tue, 11 Oct 2022 00:13:07 +0000 (17:13 -0700)]
Merge tag 'x86_mm_for_v6.1_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 mm updates from Dave Hansen:
"There are some small things here, plus one big one.
The big one detected and refused to create W+X kernel mappings. This
caused a bit of trouble and it is entirely disabled on 32-bit due to
known unfixable EFI issues. It also oopsed on some systemd eBPF use,
which kept some users from booting.
The eBPF issue is fixed, but those troubles were caught relatively
recently which made me nervous that there are more lurking. The final
commit in here retains the warnings, but doesn't actually refuse to
create W+X mappings.
Summary:
- Detect insecure W+X mappings and warn about them, including a few
bug fixes and relaxing the enforcement
- Do a long-overdue defconfig update and enabling W+X boot-time
detection
- Cleanup _PAGE_PSE handling (follow-up on an earlier bug)
- Rename a change_page_attr function"
* tag 'x86_mm_for_v6.1_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Ease W^X enforcement back to just a warning
x86/mm: Disable W^X detection and enforcement on 32-bit
x86/mm: Add prot_sethuge() helper to abstract out _PAGE_PSE handling
x86/mm/32: Fix W^X detection when page tables do not support NX
x86/defconfig: Enable CONFIG_DEBUG_WX=y
x86/defconfig: Refresh the defconfigs
x86/mm: Refuse W^X violations
x86/mm: Rename set_memory_present() to set_memory_p()
Linus Torvalds [Mon, 10 Oct 2022 21:21:11 +0000 (14:21 -0700)]
Merge tag 'xtensa-20221010' of https://github.com/jcmvbkbc/linux-xtensa
Pull xtensa updates from Max Filippov:
- add support for FDPIC and static PIE executable formats for noMMU
* tag 'xtensa-20221010' of https://github.com/jcmvbkbc/linux-xtensa:
xtensa: add FDPIC and static PIE support for noMMU
xtensa: clean up ELF_PLAT_INIT macro
Linus Torvalds [Mon, 10 Oct 2022 21:19:05 +0000 (14:19 -0700)]
Merge tag 'm68knommu-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"Just a couple of changes. Fixes to compilation of the old/legacy
Freescale 68328 targets in some kernel configurations, and some
default configuration updates.
Linus Torvalds [Mon, 10 Oct 2022 21:02:53 +0000 (14:02 -0700)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- 9k mtu perf improvements
- vdpa feature provisioning
- virtio blk SECURE ERASE support
- fixes and cleanups all over the place
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_pci: don't try to use intxif pin is zero
vDPA: conditionally read MTU and MAC in dev cfg space
vDPA: fix spars cast warning in vdpa_dev_net_mq_config_fill
vDPA: check virtio device features to detect MQ
vDPA: check VIRTIO_NET_F_RSS for max_virtqueue_paris's presence
vDPA: only report driver features if FEATURES_OK is set
vDPA: allow userspace to query features of a vDPA device
virtio_blk: add SECURE ERASE command support
vp_vdpa: support feature provisioning
vdpa_sim_net: support feature provisioning
vdpa: device feature provisioning
virtio-net: use mtu size as buffer length for big packets
virtio-net: introduce and use helper function for guest gso support checks
virtio: drop vp_legacy_set_queue_size
virtio_ring: make vring_alloc_queue_packed prettier
virtio_ring: split: Operators use unified style
vhost: add __init/__exit annotations to module init/exit funcs
Linus Torvalds [Mon, 10 Oct 2022 20:59:01 +0000 (13:59 -0700)]
Merge tag 'hyperv-next-signed-20221009' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- Remove unnecessary delay while probing for VMBus (Stanislav
Kinsburskiy)
- Optimize vmbus_on_event (Saurabh Sengar)
- Fix a race in Hyper-V DRM driver (Saurabh Sengar)
- Miscellaneous clean-up patches from various people
* tag 'hyperv-next-signed-20221009' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Replace kmap() with kmap_local_page()
drm/hyperv: Add ratelimit on error message
hyperv: simplify and rename generate_guest_id
Drivers: hv: vmbus: Split memcpy of flex-array
scsi: storvsc: remove an extraneous "to" in a comment
Drivers: hv: vmbus: Don't wait for the ACPI device upon initialization
Drivers: hv: vmbus: Use PCI_VENDOR_ID_MICROSOFT for better discoverability
Drivers: hv: vmbus: Fix kernel-doc
drm/hyperv: Don't overwrite dirt_needed value set by host
Drivers: hv: vmbus: Optimize vmbus_on_event
Linus Torvalds [Mon, 10 Oct 2022 20:52:14 +0000 (13:52 -0700)]
Merge tag 'thermal-6.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"These fix assorted issues in the thermal core and ARM thermal drivers.
Specifics:
- Use platform data to get the sensor ID instead of parsing the
device in imx_sc thermal driver and remove the dedicated OF
function from the core code (Daniel Lezcano).
- Fix Kconfig dependency for the QCom tsens thermal driver (Jonathan
Cameron).
- Add missing const annotation to the RCar ops thermal driver (Lad
Prabhakar).
- Drop duplicate parameter check from
thermal_zone_device_register_with_trips() (Lad Prabhakar).
- Fix NULL pointer dereference in trip_point_temp_store() by making
it check if the ->set_trip_temp() operation is present (Lad
Prabhakar).
- Fix the MSM8939 fourth sensor hardware ID in the QCom tsens thermal
driver (Vincent Knecht)"
* tag 'thermal-6.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/drivers/qcom/tsens-v0_1: Fix MSM8939 fourth sensor hw_id
thermal/core: Add a check before calling set_trip_temp()
thermal/core: Drop valid pointer check for type
thermal/drivers/rcar_thermal: Constify static thermal_zone_device_ops
thermal/drivers/qcom: Drop false build dependency of all QCOM drivers on QCOM_TSENS
thermal/of: Remove the thermal_zone_of_get_sensor_id() function
thermal/drivers/imx_sc: Rely on the platform data to get the resource id
Linus Torvalds [Mon, 10 Oct 2022 20:39:03 +0000 (13:39 -0700)]
Merge tag 'pm-6.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These update the turbostat utility, extend the macros used for
defining device power management callbacks and add a diagnostic
message to the generic power domains code.
Specifics:
- Add an error message to be printed when a power domain marked as
"always on" is not actually on during initialization (Johan
Hovold).
- Extend macros used for defining power management callbacks to allow
conditional exporting of noirq and late/early suspend/resume PM
callbacks (Paul Cercueil).
- Update the turbostat utility:
- Add support for two new platforms (Zhang Rui).
- Adjust energy unit for Sapphire Rapids (Zhang Rui).
- Do not dump TRL if turbo is not supported (Artem Bityutskiy)"
* tag 'pm-6.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power turbostat: version 2022.10.04
tools/power turbostat: Use standard Energy Unit for SPR Dram RAPL domain
tools/power turbostat: Do not dump TRL if turbo is not supported
tools/power turbostat: Add support for MeteorLake platforms
tools/power turbostat: Add support for RPL-S
PM: Improve EXPORT_*_DEV_PM_OPS macros
PM: domains: log failures to register always-on domains
Linus Torvalds [Mon, 10 Oct 2022 20:28:06 +0000 (13:28 -0700)]
Merge tag 'acpi-6.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These fix two issues, in APEI and in the int3472 driver, clean up the
ACPI thermal driver, add ACPI support for non-GPE system wakeup events
and make the system reboot code use the S5 (system off) state by
default.
- Fix a memory leak in APEI by avoiding to add a task_work to kernel
threads running when an asynchronous error is detected (Shuai Xue).
- Add ACPI support for handling system wakeups via GPIO wake capable
IRQs in addition to GPEs (Raul E Rangel).
- Make the system reboot code put ACPI-enabled systems into the S5
(system off) state which is necessary for some platforms to work as
expected (Kai-Heng Feng).
- Make the white space usage in the ACPI thermal driver more
consistent and drop redundant code from it (Rafael Wysocki)"
* tag 'acpi-6.1-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: thermal: Drop some redundant code
ACPI: thermal: Drop redundant parens from expressions
ACPI: thermal: Use white space more consistently
platform/x86: int3472: Don't leak reference on error
ACPI: APEI: do not add task_work to kernel thread to avoid memory leak
PM: ACPI: reboot: Reinstate S5 for reboot
kernel/reboot: Add SYS_OFF_MODE_RESTART_PREPARE mode
ACPI: PM: Take wake IRQ into consideration when entering suspend-to-idle
i2c: acpi: Use ACPI wake capability bit to set wake_irq
ACPI: resources: Add wake_capable parameter to acpi_dev_irq_flags
gpiolib: acpi: Add wake_capable variants of acpi_dev_gpio_irq_get
Linus Torvalds [Mon, 10 Oct 2022 20:24:55 +0000 (13:24 -0700)]
Merge tag 'dma-mapping-6.1-2022-10-10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- fix a regression in the ARM dma-direct conversion (Christoph Hellwig)
- use memcpy_{from,to}_page (Fabio M. De Francesco)
- cleanup the swiotlb MAINTAINERS entry (Lukas Bulwahn)
- make SG table pool allocation less fragile (Masahiro Yamada)
- don't panic on swiotlb initialization failure (Robin Murphy)
* tag 'dma-mapping-6.1-2022-10-10' of git://git.infradead.org/users/hch/dma-mapping:
ARM/dma-mapping: remove the dma_coherent member of struct dev_archdata
ARM/dma-mappÑ–ng: don't override ->dma_coherent when set from a bus notifier
lib/sg_pool: change module_init(sg_pool_init) to subsys_initcall
MAINTAINERS: merge SWIOTLB SUBSYSTEM into DMA MAPPING HELPERS
swiotlb: don't panic!
swiotlb: replace kmap_atomic() with memcpy_{from,to}_page()
Linus Torvalds [Mon, 10 Oct 2022 20:20:53 +0000 (13:20 -0700)]
Merge tag 'iommu-updates-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- remove the bus_set_iommu() interface which became unnecesary because
of IOMMU per-device probing
- make the dma-iommu.h header private
- Intel VT-d changes from Lu Baolu:
- Decouple PASID and PRI from SVA
- Add ESRTPS & ESIRTPS capability check
- Cleanups
- Apple DART support for the M1 Pro/MAX SOCs
- support for AMD IOMMUv2 page-tables for the DMA-API layer.
The v2 page-tables are compatible with the x86 CPU page-tables. Using
them for DMA-API prepares support for hardware-assisted IOMMU
virtualization
- support for MT6795 Helio X10 M4Us in the Mediatek IOMMU driver
- some smaller fixes and cleanups
* tag 'iommu-updates-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (59 commits)
iommu/vt-d: Avoid unnecessary global DMA cache invalidation
iommu/vt-d: Avoid unnecessary global IRTE cache invalidation
iommu/vt-d: Rename cap_5lp_support to cap_fl5lp_support
iommu/vt-d: Remove pasid_set_eafe()
iommu/vt-d: Decouple PASID & PRI enabling from SVA
iommu/vt-d: Remove unnecessary SVA data accesses in page fault path
dt-bindings: iommu: arm,smmu-v3: Relax order of interrupt names
iommu: dart: Support t6000 variant
iommu/io-pgtable-dart: Add DART PTE support for t6000
iommu/io-pgtable: Add DART subpage protection support
iommu/io-pgtable: Move Apple DART support to its own file
iommu/mediatek: Add support for MT6795 Helio X10 M4Us
iommu/mediatek: Introduce new flag TF_PORT_TO_ADDR_MT8173
dt-bindings: mediatek: Add bindings for MT6795 M4U
iommu/iova: Fix module config properly
iommu/amd: Fix sparse warning
iommu/amd: Remove outdated comment
iommu/amd: Free domain ID after domain_flush_pages
iommu/amd: Free domain id in error path
iommu/virtio: Fix compile error with viommu_capable()
...
Linus Torvalds [Mon, 10 Oct 2022 20:09:33 +0000 (13:09 -0700)]
Merge tag 'tpmdd-next-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
"Just a few bug fixes this time"
* tag 'tpmdd-next-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
selftest: tpm2: Add Client.__del__() to close /dev/tpm* handle
security/keys: Remove inconsistent __user annotation
char: move from strlcpy with unused retval to strscpy
Linus Torvalds [Mon, 10 Oct 2022 19:49:34 +0000 (12:49 -0700)]
Merge tag 'bitmap-6.1-rc1' of https://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- Fix unsigned comparison to -1 in CPUMAP_FILE_MAX_BYTES (Phil Auld)
- cleanup nr_cpu_ids vs nr_cpumask_bits mess (me)
This series cleans that mess and adds new config FORCE_NR_CPUS that
allows to optimize cpumask subsystem if the number of CPUs is known
at compile-time.
- optimize find_bit() functions (me)
Reworks find_bit() functions based on new FIND_{FIRST,NEXT}_BIT()
macros.
- add find_nth_bit() (me)
Adds find_nth_bit(), which is ~70 times faster than bitcounting with
for_each() loop:
for_each_set_bit(bit, mask, size)
if (n-- == 0)
return bit;
Also adds bitmap_weight_and() to let people replace this pattern:
Linus Torvalds [Mon, 10 Oct 2022 19:20:55 +0000 (12:20 -0700)]
Merge tag 'trace-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing updates from Steven Rostedt:
"Major changes:
- Changed location of tracing repo from personal git repo to:
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace.git
- Added Masami Hiramatsu as co-maintainer
- Updated MAINTAINERS file to separate out FTRACE as it is more than
just TRACING.
Minor changes:
- Added Mark Rutland as FTRACE reviewer
- Updated user_events to make it on its way to remove the BROKEN tag.
The changes should now be acceptable but will run it through a
cycle and hopefully we can remove the BROKEN tag next release.
- Added filtering to eprobes
- Added a delta time to the benchmark trace event
- Have the histogram and filter callbacks called via a switch
statement instead of indirect functions. This speeds it up to avoid
retpolines.
- Add a way to wake up ring buffer waiters waiting for the ring
buffer to fill up to its watermark.
- New ioctl() on the trace_pipe_raw file to wake up ring buffer
waiters.
- Wake up waiters when the ring buffer is disabled. A reader may
block when the ring buffer is disabled, but if it was blocked when
the ring buffer is disabled it should then wake up.
Fixes:
- Allow splice to read partially read ring buffer pages. This fixes
splice never moving forward.
- Fix inverted compare that made the "shortest" ring buffer wait
queue actually the longest.
- Fix a race in the ring buffer between resetting a page when a
writer goes to another page, and the reader.
- Fix ftrace accounting bug when function hooks are added at boot up
before the weak functions are set to "disabled".
- Fix bug that freed a user allocated snapshot buffer when enabling a
tracer.
- Fix possible recursive locks in osnoise tracer
- Fix recursive locking direct functions
- Other minor clean ups and fixes"
* tag 'trace-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: (44 commits)
ftrace: Create separate entry in MAINTAINERS for function hooks
tracing: Update MAINTAINERS to reflect new tracing git repo
tracing: Do not free snapshot if tracer is on cmdline
ftrace: Still disable enabled records marked as disabled
tracing/user_events: Move pages/locks into groups to prepare for namespaces
tracing: Add Masami Hiramatsu as co-maintainer
tracing: Remove unused variable 'dups'
MAINTAINERS: add myself as a tracing reviewer
ring-buffer: Fix race between reset page and reading page
tracing/user_events: Update ABI documentation to align to bits vs bytes
tracing/user_events: Use bits vs bytes for enabled status page data
tracing/user_events: Use refcount instead of atomic for ref tracking
tracing/user_events: Ensure user provided strings are safely formatted
tracing/user_events: Use WRITE instead of READ for io vector import
tracing/user_events: Use NULL for strstr checks
tracing: Fix spelling mistake "preapre" -> "prepare"
tracing: Wake up waiters when tracing is disabled
tracing: Add ioctl() to force ring buffer waiters to wake up
tracing: Wake up ring buffer waiters on closing of the file
ring-buffer: Add ring_buffer_wake_waiters()
...
Linus Torvalds [Mon, 10 Oct 2022 19:18:28 +0000 (12:18 -0700)]
Merge tag 'sysctl-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull sysctl updates from Luis Chamberlain:
"Just some boring cleanups on the sysctl front for this release"
* tag 'sysctl-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
kernel/sysctl-test: use SYSCTL_{ZERO/ONE_HUNDRED} instead of i_{zero/one_hundred}
kernel/sysctl.c: move sysctl_vals and sysctl_long_vals to sysctl.c
sysctl: remove max_extfrag_threshold
kernel/sysctl.c: remove unnecessary (void*) conversions
proc: remove initialization assignment
Linus Torvalds [Mon, 10 Oct 2022 19:13:36 +0000 (12:13 -0700)]
Merge tag 'modules-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module updates from Luis Chamberlain:
- minor enhancement for sysfs compression string (David Disseldorp)
- debugfs interface to view unloaded tainted modules (Aaron Tomlin)
* tag 'modules-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
module/decompress: generate sysfs string at compile time
module: Add debugfs interface to view unloaded tainted modules
Linus Torvalds [Mon, 10 Oct 2022 19:00:45 +0000 (12:00 -0700)]
Merge tag 'kbuild-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Remove potentially incomplete targets when Kbuid is interrupted by
SIGINT etc in case GNU Make may miss to do that when stderr is piped
to another program.
- Rewrite the single target build so it works more correctly.
- Fix rpm-pkg builds with V=1.
- List top-level subdirectories in ./Kbuild.
- Ignore auto-generated __kstrtab_* and __kstrtabns_* symbols in
kallsyms.
- Avoid two different modules in lib/zstd/ having shared code, which
potentially causes building the common code as build-in and modular
back-and-forth.
- Unify two modpost invocations to optimize the build process.
- Remove head-y syntax in favor of linker scripts for placing
particular sections in the head of vmlinux.
- Bump the minimal GNU Make version to 3.82.
- Clean up misc Makefiles and scripts.
* tag 'kbuild-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (41 commits)
docs: bump minimal GNU Make version to 3.82
ia64: simplify esi object addition in Makefile
Revert "kbuild: Check if linker supports the -X option"
kbuild: rebuild .vmlinux.export.o when its prerequisite is updated
kbuild: move modules.builtin(.modinfo) rules to Makefile.vmlinux_o
zstd: Fixing mixed module-builtin objects
kallsyms: ignore __kstrtab_* and __kstrtabns_* symbols
kallsyms: take the input file instead of reading stdin
kallsyms: drop duplicated ignore patterns from kallsyms.c
kbuild: reuse mksysmap output for kallsyms
mksysmap: update comment about __crc_*
kbuild: remove head-y syntax
kbuild: use obj-y instead extra-y for objects placed at the head
kbuild: hide error checker logs for V=1 builds
kbuild: re-run modpost when it is updated
kbuild: unify two modpost invocations
kbuild: move vmlinux.o rule to the top Makefile
kbuild: move .vmlinux.objs rule to Makefile.modpost
kbuild: list sub-directories in ./Kbuild
Makefile.compiler: replace cc-ifversion with compiler-specific macros
...
Linus Torvalds [Mon, 10 Oct 2022 18:36:19 +0000 (11:36 -0700)]
Merge tag 'livepatching-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching
Pull livepatching updates from Petr Mladek:
- Fix race between fork and livepatch transition revert
- Add sysfs entry that shows "patched" state for each object (module)
that can be livepatched by the given livepatch
- Some clean up
* tag 'livepatching-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/livepatching/livepatching:
selftests/livepatch: add sysfs test
livepatch: add sysfs entry "patched" for each klp_object
selftests/livepatch: normalize sysctl error message
livepatch: Add a missing newline character in klp_module_coming()
livepatch: fix race between fork and KLP transition
Linus Torvalds [Mon, 10 Oct 2022 18:24:19 +0000 (11:24 -0700)]
Merge tag 'printk-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Initialize pointer hashing using the system workqueue. It avoids
taking locks in printk()/vsprintf() code path
- Misc code clean up
* tag 'printk-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: Mark __printk percpu data ready __ro_after_init
printk: Remove bogus comment vs. boot consoles
printk: Remove write only variable nr_ext_console_drivers
printk: Declare log_wait properly
printk: Make pr_flush() static
lib/vsprintf: Initialize vsprintf's pointer hash once the random core is ready.
lib/vsprintf: Remove static_branch_likely() from __ptr_to_hashval().
lib/vnsprintf: add const modifier for param 'bitmap'
Linus Torvalds [Mon, 10 Oct 2022 18:12:25 +0000 (11:12 -0700)]
Merge tag 'cgroup-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
- cpuset now support isolated cpus.partition type, which will enable
dynamic CPU isolation
- pids.peak added to remember the max number of pids used
- holes in cgroup namespace plugged
- internal cleanups
* tag 'cgroup-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (25 commits)
cgroup: use strscpy() is more robust and safer
iocost_monitor: reorder BlkgIterator
cgroup: simplify code in cgroup_apply_control
cgroup: Make cgroup_get_from_id() prettier
cgroup/cpuset: remove unreachable code
cgroup: Remove CFTYPE_PRESSURE
cgroup: Improve cftype add/rm error handling
kselftest/cgroup: Add cpuset v2 partition root state test
cgroup/cpuset: Update description of cpuset.cpus.partition in cgroup-v2.rst
cgroup/cpuset: Make partition invalid if cpumask change violates exclusivity rule
cgroup/cpuset: Relocate a code block in validate_change()
cgroup/cpuset: Show invalid partition reason string
cgroup/cpuset: Add a new isolated cpus.partition type
cgroup/cpuset: Relax constraints to partition & cpus changes
cgroup/cpuset: Allow no-task partition to have empty cpuset.cpus.effective
cgroup/cpuset: Miscellaneous cleanups & add helper functions
cgroup/cpuset: Enable update_tasks_cpumask() on top_cpuset
cgroup: add pids.peak interface for pids controller
cgroup: Remove data-race around cgrp_dfl_visible
cgroup: Fix build failure when CONFIG_SHRINKER_DEBUG
...
Linus Torvalds [Mon, 10 Oct 2022 17:41:21 +0000 (10:41 -0700)]
Merge tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Huawei reported that when they updated their kernel from 4.4 to
something much newer, some userspace code they had broke, the culprit
being the accidental removal of O_NONBLOCK from /dev/random way back
in 5.6. It's been gone for over 2 years now and this is the first
we've heard of it, but userspace breakage is userspace breakage, so
O_NONBLOCK is now back.
- Use randomness from hardware RNGs much more often during early boot,
at the same interval that crng reseeds are done, from Dominik.
- A semantic change in hardware RNG throttling, so that the hwrng
framework can properly feed random.c with randomness from hardware
RNGs that aren't specifically marked as creditable.
A related patch coming to you via Herbert's hwrng tree depends on
this one, not to compile, but just to function properly, so you may
want to merge this PULL before that one.
- A fix to clamp credited bits from the interrupts pool to the size of
the pool sample. This is mainly just a theoretical fix, as it'd be
pretty hard to exceed it in practice.
- Oracle reported that InfiniBand TCP latency regressed by around
10-15% after a change a few cycles ago made at the request of the RT
folks, in which we hoisted a somewhat rare operation (1 in 1024
times) out of the hard IRQ handler and into a workqueue, a pretty
common and boring pattern.
It turns out, though, that scheduling a worker from there has
overhead of its own, whereas scheduling a timer on that same CPU for
the next jiffy amortizes better and doesn't incur the same overhead.
I also eliminated a cache miss by moving the work_struct (and
subsequently, the timer_list) to below a critical cache line, so that
the more critical members that are accessed on every hard IRQ aren't
split between two cache lines.
- The boot-time initialization of the RNG has been split into two
approximate phases: what we can accomplish before timekeeping is
possible and what we can accomplish after.
This winds up being useful so that we can use RDRAND to seed the RNG
before CONFIG_SLAB_FREELIST_RANDOM=y systems initialize slabs, in
addition to other early uses of randomness. The effect is that
systems with RDRAND (or a bootloader seed) will never see any
warnings at all when setting CONFIG_WARN_ALL_UNSEEDED_RANDOM=y. And
kfence benefits from getting a better seed of its own.
- Small systems without much entropy sometimes wind up putting some
truncated serial number read from flash into hostname, so contribute
utsname changes to the RNG, without crediting.
- Add smaller batches to serve requests for smaller integers, and make
use of them when people ask for random numbers bounded by a given
compile-time constant. This has positive effects all over the tree,
most notably in networking and kfence.
- The original jitter algorithm intended (I believe) to schedule the
timer for the next jiffy, not the next-next jiffy, yet it used
mod_timer(jiffies + 1), which will fire on the next-next jiffy,
instead of what I believe was intended, mod_timer(jiffies), which
will fire on the next jiffy. So fix that.
- Fix a comment typo, from William.
* tag 'random-6.1-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: clear new batches when bringing new CPUs online
random: fix typos in get_random_bytes() comment
random: schedule jitter credit for next jiffy, not in two jiffies
prandom: make use of smaller types in prandom_u32_max
random: add 8-bit and 16-bit batches
utsname: contribute changes to RNG
random: use init_utsname() instead of utsname()
kfence: use better stack hash seed
random: split initialization into early step and later step
random: use expired timer rather than wq for mixing fast pool
random: avoid reading two cache lines on irq randomness
random: clamp credited irq bits to maximum mixed
random: throttle hwrng writes if no entropy is credited
random: use hwgenerator randomness more frequently at early boot
random: restore O_NONBLOCK support
Linus Torvalds [Mon, 10 Oct 2022 17:21:22 +0000 (10:21 -0700)]
Merge tag 'slab-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab
Pull slab fixes from Vlastimil Babka:
- The "common kmalloc v4" series [1] by Hyeonggon Yoo.
While the plan after LPC is to try again if it's possible to get rid
of SLOB and SLAB (and if any critical aspect of those is not possible
to achieve with SLUB today, modify it accordingly), it will take a
while even in case there are no objections.
Meanwhile this is a nice cleanup and some parts (e.g. to the
tracepoints) will be useful even if we end up with a single slab
implementation in the future:
- Improves the mm/slab_common.c wrappers to allow deleting
duplicated code between SLAB and SLUB.
- Large kmalloc() allocations in SLAB are passed to page allocator
like in SLUB, reducing number of kmalloc caches.
- Removes the {kmem_cache_alloc,kmalloc}_node variants of
tracepoints, node id parameter added to non-_node variants.
- Addition of kmalloc_size_roundup()
The first two patches from a series by Kees Cook [2] that introduce
kmalloc_size_roundup(). This will allow merging of per-subsystem
patches using the new function and ultimately stop (ab)using ksize()
in a way that causes ongoing trouble for debugging functionality and
static checkers.
- Wasted kmalloc() memory tracking in debugfs alloc_traces
A patch from Feng Tang that enhances the existing debugfs
alloc_traces file for kmalloc caches with information about how much
space is wasted by allocations that needs less space than the
particular kmalloc cache provides.
- My series [3] to fix validation races for caches with enabled
debugging:
- By decoupling the debug cache operation more from non-debug
fastpaths, extra locking simplifications were possible and thus
done afterwards.
- Additional cleanup of PREEMPT_RT specific code on top, by Thomas
Gleixner.
- A late fix for slab page leaks caused by the series, by Feng
Tang.
- Smaller fixes and cleanups:
- Unneeded variable removals, by ye xingchen
- A cleanup removing a BUG_ON() in create_unique_id(), by Chao Yu
Link: https://lore.kernel.org/all/20220817101826.236819-1-42.hyeyoo@gmail.com/ Link: https://lore.kernel.org/all/20220923202822.2667581-1-keescook@chromium.org/ Link: https://lore.kernel.org/all/20220823170400.26546-1-vbabka@suse.cz/
* tag 'slab-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab: (30 commits)
mm/slub: fix a slab missed to be freed problem
slab: Introduce kmalloc_size_roundup()
slab: Remove __malloc attribute from realloc functions
mm/slub: clean up create_unique_id()
mm/slub: enable debugging memory wasting of kmalloc
slub: Make PREEMPT_RT support less convoluted
mm/slub: simplify __cmpxchg_double_slab() and slab_[un]lock()
mm/slub: convert object_map_lock to non-raw spinlock
mm/slub: remove slab_lock() usage for debug operations
mm/slub: restrict sysfs validation to debug caches and make it safe
mm/sl[au]b: check if large object is valid in __ksize()
mm/slab_common: move declaration of __ksize() to mm/slab.h
mm/slab_common: drop kmem_alloc & avoid dereferencing fields when not using
mm/slab_common: unify NUMA and UMA version of tracepoints
mm/sl[au]b: cleanup kmem_cache_alloc[_node]_trace()
mm/sl[au]b: generalize kmalloc subsystem
mm/slub: move free_debug_processing() further
mm/sl[au]b: introduce common alloc/free functions without tracepoint
mm/slab: kmalloc: pass requests larger than order-1 page to page allocator
mm/slab_common: cleanup kmalloc_large()
...
Linus Torvalds [Mon, 10 Oct 2022 17:16:00 +0000 (10:16 -0700)]
Merge tag 'timers-core-2022-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A boring time, timekeeping, timers update:
- No core code changes
- No new clocksource/event driver
- Cleanup of the TI DM clocksource/event driver
- The usual set of device tree binding updates
- Small improvement, fixes and cleanups all over the place"
* tag 'timers-core-2022-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
clocksource/drivers/arm_arch_timer: Fix CNTPCT_LO and CNTVCT_LO value
clocksource/drivers/imx-sysctr: handle nxp,no-divider property
dt-bindings: timer: nxp,sysctr-timer: add nxp,no-divider property
clocksource/drivers/timer-ti-dm: Get clock in probe with devm_clk_get()
clocksource/drivers/timer-ti-dm: Add flag to detect omap1
clocksource/drivers/timer-ti-dm: Move struct omap_dm_timer fields to driver
clocksource/drivers/timer-ti-dm: Use runtime PM directly and check errors
clocksource/drivers/timer-ti-dm: Move private defines to the driver
clocksource/drivers/timer-ti-dm: Simplify register access further
clocksource/drivers/timer-ti-dm: Simplify register writes with dmtimer_write()
clocksource/drivers/timer-ti-dm: Simplify register reads with dmtimer_read()
clocksource/drivers/timer-ti-dm: Drop unused functions
clocksource/drivers/timer-gxp: Add missing error handling in gxp_timer_probe
clocksource/drivers/arm_arch_timer: Fix handling of ARM erratum 858921
clocksource/drivers/exynos_mct: Enable building on ARTPEC
clocksource/drivers/exynos_mct: Support local-timers property
clocksource/drivers/exynos_mct: Support frc-shared property
dt-bindings: timer: exynos4210-mct: Add ARTPEC-8 MCT support
clocksource/drivers/sun4i: Add definition of clear interrupt
clocksource/drivers/renesas-ostm: Add support for RZ/V2L SoC
...
Linus Torvalds [Mon, 10 Oct 2022 17:03:24 +0000 (10:03 -0700)]
Merge tag 'sched-rt-2022-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull preempt RT updates from Thomas Gleixner:
"Introduce preempt_[dis|enable_nested() and use it to clean up various
places which have open coded PREEMPT_RT conditionals.
On PREEMPT_RT enabled kernels, spinlocks and rwlocks are neither
disabling preemption nor interrupts. Though there are a few places
which depend on the implicit preemption/interrupt disable of those
locks, e.g. seqcount write sections, per CPU statistics updates etc.
PREEMPT_RT added open coded CONFIG_PREEMPT_RT conditionals to
disable/enable preemption in the related code parts all over the
place. That's hard to read and does not really explain why this is
necessary.
Linus suggested to use helper functions (preempt_disable_nested() and
preempt_enable_nested()) and use those in the affected places. On !RT
enabled kernels these functions are NOPs, but contain a lockdep assert
to validate that preemption is actually disabled to catch call sites
which do not have preemption disabled.
Clean up the affected code paths in mm, dentry and lib"
* tag 'sched-rt-2022-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
u64_stats: Streamline the implementation
flex_proportions: Disable preemption entering the write section.
mm/compaction: Get rid of RT ifdeffery
mm/memcontrol: Replace the PREEMPT_RT conditionals
mm/debug: Provide VM_WARN_ON_IRQS_ENABLED()
mm/vmstat: Use preempt_[dis|en]able_nested()
dentry: Use preempt_[dis|en]able_nested()
preempt: Provide preempt_[dis|en]able_nested()
Linus Torvalds [Mon, 10 Oct 2022 16:56:19 +0000 (09:56 -0700)]
Merge tag 'objtool-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool updates from Ingo Molnar:
- Remove the "ANNOTATE_NOENDBR on ENDBR" warning: it's not really
useful and only found a non-bug false positive so far.
- Properly decode LOOP/LOOPE/LOOPNE, which were missing from the x86
decoder. Because these instructions are rather ineffective, they
never showed up in compiler output, but they are simple enough to
support, so add them for completeness.
- A bit more cross-arch preparatory work.
* tag 'objtool-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool,x86: Teach decode about LOOP* instructions
objtool: Remove "ANNOTATE_NOENDBR on ENDBR" warning
objtool: Use arch_jump_destination() in read_intra_function_calls()
Linus Torvalds [Mon, 10 Oct 2022 16:44:12 +0000 (09:44 -0700)]
Merge tag 'locking-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
- Disable preemption in rwsem_write_trylock()'s attempt to take the
rwsem, to avoid RT tasks hogging the CPU, which managed to preempt
this function after the owner has been cleared but before a new owner
is set. Also add debug checks to enforce this.
- Add __lockfunc to more slow path functions and add __sched to
semaphore functions.
- Mark spinlock APIs noinline when the respective CONFIG_INLINE_SPIN_*
toggles are disabled, to reduce LTO text size.
- Print more debug information when lockdep gets confused in
look_up_lock_class().
- Improve header file abuse checks.
- Misc cleanups
* tag 'locking-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Print more debug information - report name and key when look_up_lock_class() got confused
locking: Add __sched to semaphore functions
locking/rwsem: Disable preemption while trying for rwsem lock
locking: Detect includes rwlock.h outside of spinlock.h
locking: Add __lockfunc to slow path functions
locking/spinlocks: Mark spinlocks noinline when inline spinlocks are disabled
selftests: futex: Fix 'the the' typo in comment
Merge additional generic power domains handling update and an
improvement of the PM callback definition macros for 6.1-rc1:
- Add an error message to be printed when a power domain marked as
"always on" is not actually on during initialization (Johan Hovold).
- Extend macros used for defining power management callbacks to allow
conditional exporting of noirq and late/early suspend/resume PM
callbacks (Paul Cercueil).
* pm-domains:
PM: domains: log failures to register always-on domains
- Add 'perf mem' and 'perf c2c' memory profiling support on AMD CPUs
by utilizing IBS tagged load/store samples.
- Clean up & optimize various x86 PMU details.
HW breakpoints:
- Big rework to optimize the code for systems with hundreds of CPUs
and thousands of breakpoints:
- Replace the nr_bp_mutex global mutex with the bp_cpuinfo_sem
per-CPU rwsem that is read-locked during most of the key
operations.
- Improve the O(#cpus * #tasks) logic in toggle_bp_slot() and
fetch_bp_busy_slots().
- Apply micro-optimizations & cleanups.
- Misc cleanups & enhancements"
* tag 'perf-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (75 commits)
perf/hw_breakpoint: Annotate tsk->perf_event_mutex vs ctx->mutex
perf: Fix pmu_filter_match()
perf: Fix lockdep_assert_event_ctx()
perf/x86/amd/lbr: Adjust LBR regardless of filtering
perf/x86/utils: Fix uninitialized var in get_branch_type()
perf/uapi: Define PERF_MEM_SNOOPX_PEER in kernel header file
perf/x86/amd: Support PERF_SAMPLE_PHY_ADDR
perf/x86/amd: Support PERF_SAMPLE_ADDR
perf/x86/amd: Support PERF_SAMPLE_{WEIGHT|WEIGHT_STRUCT}
perf/x86/amd: Support PERF_SAMPLE_DATA_SRC
perf/x86/amd: Add IBS OP_DATA2 DataSrc bit definitions
perf/mem: Introduce PERF_MEM_LVLNUM_{EXTN_MEM|IO}
perf/x86/uncore: Add new Raptor Lake S support
perf/x86/cstate: Add new Raptor Lake S support
perf/x86/msr: Add new Raptor Lake S support
perf/x86: Add new Raptor Lake S support
bpf: Check flags for branch stack in bpf_read_branch_records helper
perf, hw_breakpoint: Fix use-after-free if perf_event_open() fails
perf: Use sample_flags for raw_data
perf: Use sample_flags for addr
...
Merge branches 'acpi-apei', 'acpi-wakeup', 'acpi-reboot' and 'acpi-thermal'
Merge additional APEI changes, ACPI updates related to device wakeup and
system restart and ACPI thermal driver cleanups for 6.1-rc1:
- Fix a memory leak in APEI by avoiding to add do not add task_work to
kernel threads running when an asynchronous error is detected (Shuai
Xue).
- Add ACPI support for handling system wakeups via GPIO wake capable
IRQs in addition to GPEs (Raul E Rangel).
- Make the system reboot code put ACPI-enabled systems into the S5
(system off) state which is necessary for some platforms to work as
expected (Kai-Heng Feng).
- Make the white space usage in the ACPI thermal driver more consistent
and drop redundant code from it (Rafael Wysocki).
* acpi-apei:
ACPI: APEI: do not add task_work to kernel thread to avoid memory leak
* acpi-wakeup:
ACPI: PM: Take wake IRQ into consideration when entering suspend-to-idle
i2c: acpi: Use ACPI wake capability bit to set wake_irq
ACPI: resources: Add wake_capable parameter to acpi_dev_irq_flags
gpiolib: acpi: Add wake_capable variants of acpi_dev_gpio_irq_get
* acpi-thermal:
ACPI: thermal: Drop some redundant code
ACPI: thermal: Drop redundant parens from expressions
ACPI: thermal: Use white space more consistently
Linus Torvalds [Mon, 10 Oct 2022 16:10:28 +0000 (09:10 -0700)]
Merge tag 'sched-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"Debuggability:
- Change most occurances of BUG_ON() to WARN_ON_ONCE()
- Reorganize & fix TASK_ state comparisons, turn it into a bitmap
- Update/fix misc scheduler debugging facilities
Load-balancing & regular scheduling:
- Improve the behavior of the scheduler in presence of lot of
SCHED_IDLE tasks - in particular they should not impact other
scheduling classes.
- Optimize task load tracking, cleanups & fixes
- Clean up & simplify misc load-balancing code
Freezer:
- Rewrite the core freezer to behave better wrt thawing and be
simpler in general, by replacing PF_FROZEN with TASK_FROZEN &
fixing/adjusting all the fallout.
Deadline scheduler:
- Fix the DL capacity-aware code
- Factor out dl_task_is_earliest_deadline() &
replenish_dl_new_period()
- Relax/optimize locking in task_non_contending()
Cleanups:
- Factor out the update_current_exec_runtime() helper
- Various cleanups, simplifications"
* tag 'sched-core-2022-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
sched: Fix more TASK_state comparisons
sched: Fix TASK_state comparisons
sched/fair: Move call to list_last_entry() in detach_tasks
sched/fair: Cleanup loop_max and loop_break
sched/fair: Make sure to try to detach at least one movable task
sched: Show PF_flag holes
freezer,sched: Rewrite core freezer logic
sched: Widen TAKS_state literals
sched/wait: Add wait_event_state()
sched/completion: Add wait_for_completion_state()
sched: Add TASK_ANY for wait_task_inactive()
sched: Change wait_task_inactive()s match_state
freezer,umh: Clean up freezer/initrd interaction
freezer: Have {,un}lock_system_sleep() save/restore flags
sched: Rename task_running() to task_on_cpu()
sched/fair: Cleanup for SIS_PROP
sched/fair: Default to false in test_idle_cores()
sched/fair: Remove useless check in select_idle_core()
sched/fair: Avoid double search on same cpu
sched/fair: Remove redundant check in select_idle_smt()
...
Liang He [Sat, 1 Oct 2022 21:42:24 +0000 (14:42 -0700)]
Input: i8042 - fix refount leak on sparc
In i8042_platform_init() and i8042_platform_exit(), we should call
of_node_put() for the reference 'root' returned by
of_find_node_by_path() which has increased the refcount.
Fixes: 5a2d7b904e01 ("[SERIO] i8042-sparcio.h: Convert to of_driver framework.") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220711064300.358757-1-windhl@126.com
[dtor: rearranged i8042_is_mr_coffee() a bit] Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Huacai Chen [Sat, 1 Oct 2022 21:29:01 +0000 (14:29 -0700)]
Input: i8042 - add LoongArch support in i8042-acpipnpio.h
LoongArch uses ACPI and nearly the same as X86/IA64 for 8042. So modify
i8042-acpipnpio.h slightly and enable it for LoongArch in i8042.h. Then
i8042 driver can work well under the ACPI firmware with PNP typed key-
board and mouse configured in DSDT.
Huacai Chen [Sat, 1 Oct 2022 21:28:34 +0000 (14:28 -0700)]
Input: i8042 - rename i8042-x86ia64io.h to i8042-acpipnpio.h
Now i8042-x86ia64io.h is shared by X86 and IA64, but it can be shared
by more platforms (such as LoongArch) with ACPI firmware on which PNP
typed keyboard and mouse is configured in DSDT. So rename it to i8042-
acpipnpio.h.
Samuel Holland [Sat, 1 Oct 2022 05:53:23 +0000 (22:53 -0700)]
Input: pinephone-keyboard - support the proxied I2C bus
The PinePhone keyboard case contains a battery managed by an integrated
power bank IC. The power bank IC communicates over I2C, and the keyboard
MCU firmware provides an interface to read and write its registers.
Let's use this interface to implement a SMBus adapter, so we can reuse
the driver for the power bank IC.
Linus Torvalds [Sun, 9 Oct 2022 23:24:05 +0000 (16:24 -0700)]
Merge tag 'ucount-rlimits-cleanups-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ucounts update from Eric Biederman:
"Split rlimit and ucount values and max values
After the ucount rlimit code was merged a bunch of small but
siginificant bugs were found and fixed. At the time it was realized
that part of the problem was that while the ucount rlimits were very
similar to the oridinary ucounts (in being nested counts with limits)
the semantics were slightly different and the code would be less error
prone if there was less sharing.
This is the long awaited cleanup that should hopefully keep things
more comprehensible and less error prone for whoever needs to touch
that code next"
* tag 'ucount-rlimits-cleanups-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Split rlimit and ucount values and max values
Linus Torvalds [Sun, 9 Oct 2022 23:14:15 +0000 (16:14 -0700)]
Merge tag 'signal-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ptrace update from Eric Biederman:
"ptrace: Stop supporting SIGKILL for PTRACE_EVENT_EXIT
Recently I had a conversation where it was pointed out to me that
SIGKILL sent to a tracee stropped in PTRACE_EVENT_EXIT is quite
difficult for a tracer to handle.
Keeping SIGKILL working after the process has been killed is pain from
an implementation point of view.
So since the debuggers don't want this behavior let's see if we can
remove this wart for the userspace API
If a regression is detected it should only need to be the last change
that is the reverted. The other two are just general cleanups that
make the last patch simpler"
* tag 'signal-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Drop signals received after a fatal signal has been processed
signal: Guarantee that SIGNAL_GROUP_EXIT is set on process exit
signal: Ensure SIGNAL_GROUP_EXIT gets set in do_group_exit
Linus Torvalds [Sun, 9 Oct 2022 23:10:22 +0000 (16:10 -0700)]
Merge tag 'retire_mq_sysctls-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull mqueue fix from Eric Biederman:
"A fix for an unlikely but possible memory leak"
* tag 'retire_mq_sysctls-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ipc: mqueue: fix possible memory leak in init_mqueue_fs()
Linus Torvalds [Sun, 9 Oct 2022 23:01:59 +0000 (16:01 -0700)]
Merge tag 'interrupting_kthread_stop-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull kthread update from Eric Biederman:
"Break out of wait loops on kthread_stop()
This is a small tweak to kthread_stop so it breaks out of
interruptible waits, that don't explicitly test for kthread_stop.
These interruptible waits occassionaly occur in kernel threads do to
code sharing"
* tag 'interrupting_kthread_stop-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: break out of wait loops on kthread_stop()
Linus Torvalds [Sun, 9 Oct 2022 20:51:40 +0000 (13:51 -0700)]
Merge tag 's390-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Make use of the IBM z16 processor activity instrumentation facility
extension to count neural network processor assist operations: add a
new PMU device driver so that perf can make use of this.
- Rework memcpy_real() to avoid DAT-off mode.
- Rework absolute lowcore access code.
- Various small fixes and improvements all over the code.
* tag 's390-6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: remove unused bus_next field from struct zpci_dev
s390/cio: remove unused ccw_device_force_console() declaration
s390/pai: Add support for PAI Extension 1 NNPA counters
s390/mm: fix no previous prototype warnings in maccess.c
s390/mm: uninline copy_oldmem_kernel() function
s390/mm,ptdump: add real memory copy page markers
s390/mm: rework memcpy_real() to avoid DAT-off mode
s390/dump: save IPL CPU registers once DAT is available
s390/pci: convert high_memory to physical address
s390/smp,ptdump: add absolute lowcore markers
s390/smp: rework absolute lowcore access
s390/smp: call smp_reinit_ipl_cpu() before scheduler is available
s390/ptdump: add missing amode31 markers
s390/mm: split lowcore pages with set_memory_4k()
s390/mm: remove unused access parameter from do_fault_error()
s390/delay: sync comment within __delay() with reality
s390: move from strlcpy with unused retval to strscpy
Linus Torvalds [Sun, 9 Oct 2022 20:13:48 +0000 (13:13 -0700)]
Merge tag 'microblaze-v6.1' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze updates from Michal Simek:
"This adds architecture support for error injection which can be done
only via local memory (BRAM) with enabling path for recovery after
reset.
These patches targets Triple Modular Redundacy (TMR) configuration
where 3 Microblazes are running in parallel with monitoring logic.
When an error happens (or is injected) system goes to break handler
with full CPU reset and system recovery back to origin context. More
information can be found at [1]"
Linus Torvalds [Sun, 9 Oct 2022 16:39:55 +0000 (09:39 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm updates from Paolo Bonzini:
"The first batch of KVM patches, mostly covering x86.
ARM:
- Account stage2 page table allocations in memory stats
x86:
- Account EPT/NPT arm64 page table allocations in memory stats
- Tracepoint cleanups/fixes for nested VM-Enter and emulated MSR
accesses
- Drop eVMCS controls filtering for KVM on Hyper-V, all known
versions of Hyper-V now support eVMCS fields associated with
features that are enumerated to the guest
- Use KVM's sanitized VMCS config as the basis for the values of
nested VMX capabilities MSRs
- A myriad event/exception fixes and cleanups. Most notably, pending
exceptions morph into VM-Exits earlier, as soon as the exception is
queued, instead of waiting until the next vmentry. This fixed a
longstanding issue where the exceptions would incorrecly become
double-faults instead of triggering a vmexit; the common case of
page-fault vmexits had a special workaround, but now it's fixed for
good
- A handful of fixes for memory leaks in error paths
- Cleanups for VMREAD trampoline and VMX's VM-Exit assembly flow
- Never write to memory from non-sleepable kvm_vcpu_check_block()
- Selftests refinements and cleanups
- Misc typo cleanups
Generic:
- remove KVM_REQ_UNHALT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (94 commits)
KVM: remove KVM_REQ_UNHALT
KVM: mips, x86: do not rely on KVM_REQ_UNHALT
KVM: x86: never write to memory from kvm_vcpu_check_block()
KVM: x86: Don't snapshot pending INIT/SIPI prior to checking nested events
KVM: nVMX: Make event request on VMXOFF iff INIT/SIPI is pending
KVM: nVMX: Make an event request if INIT or SIPI is pending on VM-Enter
KVM: SVM: Make an event request if INIT or SIPI is pending when GIF is set
KVM: x86: lapic does not have to process INIT if it is blocked
KVM: x86: Rename kvm_apic_has_events() to make it INIT/SIPI specific
KVM: x86: Rename and expose helper to detect if INIT/SIPI are allowed
KVM: nVMX: Make an event request when pending an MTF nested VM-Exit
KVM: x86: make vendor code check for all nested events
mailmap: Update Oliver's email address
KVM: x86: Allow force_emulation_prefix to be written without a reload
KVM: selftests: Add an x86-only test to verify nested exception queueing
KVM: selftests: Use uapi header to get VMX and SVM exit reasons/codes
KVM: x86: Rename inject_pending_events() to kvm_check_and_inject_events()
KVM: VMX: Update MTF and ICEBP comments to document KVM's subtle behavior
KVM: x86: Treat pending TRIPLE_FAULT requests as pending exceptions
KVM: x86: Morph pending exceptions to pending VM-Exits at queue time
...
Linus Torvalds [Sun, 9 Oct 2022 15:56:54 +0000 (08:56 -0700)]
Merge tag 'efi-next-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI updates from Ard Biesheuvel:
"A bit more going on than usual in the EFI subsystem. The main driver
for this has been the introduction of the LoonArch architecture last
cycle, which inspired some cleanup and refactoring of the EFI code.
Another driver for EFI changes this cycle and in the future is
confidential compute.
The LoongArch architecture does not use either struct bootparams or DT
natively [yet], and so passing information between the EFI stub and
the core kernel using either of those is undesirable. And in general,
overloading DT has been a source of issues on arm64, so using DT for
this on new architectures is a to avoid for the time being (even if we
might converge on something DT based for non-x86 architectures in the
future). For this reason, in addition to the patch that enables EFI
boot for LoongArch, there are a number of refactoring patches applied
on top of which separate the DT bits from the generic EFI stub bits.
These changes are on a separate topich branch that has been shared
with the LoongArch maintainers, who will include it in their pull
request as well. This is not ideal, but the best way to manage the
conflicts without stalling LoongArch for another cycle.
Another development inspired by LoongArch is the newly added support
for EFI based decompressors. Instead of adding yet another
arch-specific incarnation of this pattern for LoongArch, we are
introducing an EFI app based on the existing EFI libstub
infrastructure that encapulates the decompression code we use on other
architectures, but in a way that is fully generic. This has been
developed and tested in collaboration with distro and systemd folks,
who are eager to start using this for systemd-boot and also for arm64
secure boot on Fedora. Note that the EFI zimage files this introduces
can also be decompressed by non-EFI bootloaders if needed, as the
image header describes the location of the payload inside the image,
and the type of compression that was used. (Note that Fedora's arm64
GRUB is buggy [0] so you'll need a recent version or switch to
systemd-boot in order to use this.)
Finally, we are adding TPM measurement of the kernel command line
provided by EFI. There is an oversight in the TCG spec which results
in a blind spot for command line arguments passed to loaded images,
which means that either the loader or the stub needs to take the
measurement. Given the combinatorial explosion I am anticipating when
it comes to firmware/bootloader stacks and firmware based attestation
protocols (SEV-SNP, TDX, DICE, DRTM), it is good to set a baseline now
when it comes to EFI measured boot, which is that the kernel measures
the initrd and command line. Intermediate loaders can measure
additional assets if needed, but with the baseline in place, we can
deploy measured boot in a meaningful way even if you boot into Linux
straight from the EFI firmware.
Summary:
- implement EFI boot support for LoongArch
- implement generic EFI compressed boot support for arm64, RISC-V and
LoongArch, none of which implement a decompressor today
- measure the kernel command line into the TPM if measured boot is in
effect
- refactor the EFI stub code in order to isolate DT dependencies for
architectures other than x86
- avoid calling SetVirtualAddressMap() on arm64 if the configured
size of the VA space guarantees that doing so is unnecessary
- move some ARM specific code out of the generic EFI source files
- unmap kernel code from the x86 mixed mode 1:1 page tables"
* tag 'efi-next-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: (24 commits)
efi/arm64: libstub: avoid SetVirtualAddressMap() when possible
efi: zboot: create MemoryMapped() device path for the parent if needed
efi: libstub: fix up the last remaining open coded boot service call
efi/arm: libstub: move ARM specific code out of generic routines
efi/libstub: measure EFI LoadOptions
efi/libstub: refactor the initrd measuring functions
efi/loongarch: libstub: remove dependency on flattened DT
efi: libstub: install boot-time memory map as config table
efi: libstub: remove DT dependency from generic stub
efi: libstub: unify initrd loading between architectures
efi: libstub: remove pointless goto kludge
efi: libstub: simplify efi_get_memory_map() and struct efi_boot_memmap
efi: libstub: avoid efi_get_memory_map() for allocating the virt map
efi: libstub: drop pointless get_memory_map() call
efi: libstub: fix type confusion for load_options_size
arm64: efi: enable generic EFI compressed boot
loongarch: efi: enable generic EFI compressed boot
riscv: efi: enable generic EFI compressed boot
efi/libstub: implement generic EFI zboot
efi/libstub: move efi_system_table global var into separate object
...
Linus Torvalds [Sat, 8 Oct 2022 17:06:48 +0000 (10:06 -0700)]
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have some late breaking reports that a patch series to rework clk
rate range support broke boot on some devices, so I've left that
branch out of this. Hopefully we can get to that next week, or punt on
it and let it bake another cycle. That means we don't really have any
changes to the core framework this time around besides a few typo
fixes. Instead this is all clk driver updates and fixes.
The usual suspects are here (again), with Qualcomm dominating the
diffstat. We look to have gained support for quite a few new Qualcomm
SoCs and Dmitry worked on updating many of the existing Qualcomm
drivers to use clk_parent_data. After that we have MediaTek drivers
getting some much needed updates, in particular to support GPU DVFS.
There are also quite a few Samsung clk driver patches, but that's
mostly because there was a maintainer change and so last release we
missed some of those patches.
Overall things look normal, but I'm slowly reviewing core framework
code nowadays and that shows given the rate range patches had to be
yanked last minute. Let's hope this situation changes soon.
New Drivers:
- Support for Renesas VersaClock7 clock generator family
- Add Spreadtrum UMS512 SoC clk support
- New clock drivers for MediaTek Helio X10 MT6795
- Display clks for Qualcomm SM6115, SM8450
- GPU clks for Qualcomm SC8280XP
- Qualcomm MSM8909 and SM6375 global and SMD RPM clk drivers
Deleted Drivers:
- Remove DaVinci DM644x and DM646x clk driver support
Updates:
- Convert Baikal-T1 CCU driver to platform driver
- Split reset support out of primary Baikal-T1 CCU driver
- Add some missing clks required for RPiVid Video Decoder on
RaspberryPi
- Mark PLLC critical on bcm2835
- More devm helpers for fixed rate registration
- Various PXA168 clk driver fixes
- Add resets for MediaTek MT8195 PCIe and USB
- Miscellaneous of_node_put() fixes
- Nuke dt-bindings/clk path (again) by moving headers to
dt-bindings/clock
- Convert gpio-clk-gate binding to YAML
- Various fixes to AMD/Xilinx Zynqmp clk driver
- Graduate AMD/Xilinx "clocking wizard" driver from staging
- Add missing DPI1_HDMI clock in MT8195 VDOSYS1
- Clock driver changes to support GPU DVFS on MT8183, MT8192, MT8195
- Fix GPU clock topology on MT8195
- Propogate rate changes from GPU clock gate up the tree
- Clock mux notifiers for GPU-related PLLs
- Conversion of more "simple" drivers to mtk_clk_simple_probe()
- Hook up mtk_clk_simple_remove() for "simple" MT8192 clock drivers
- Fixes to previous |struct clk| to |struct clk_hw| conversion on
MediaTek
- Shrink MT8192 clock driver by deduplicating clock parent lists
- Change order between 'sim_enet_root_clk' and 'enet_qos_root_clk'
clocks for i.MX8MP
- Drop unnecessary newline in i.MX8MM dt-bindings
- Add more MU1 and SAI clocks dt-bindings Ids
- Introduce slice busy bit check for i.MX93 composite clock
- Introduce white list bit check for i.MX93 composite clock
- Add new i.MX93 clock gate
- Add MU1 and MU2 clocks to i.MX93 clock provider
- Add SAI IPG clocks to i.MX93 clock provider
- add generic clocks for U(S)ART available on SAMA5D2 SoCs
- reset controller support for Polarfire clocks
- .round_rate and .set rate support for clk-mpfs
- code cleanup for clk-mpfs
- PLL support for PolarFire SoC's Clock Conditioning Circuitry
- Add watchdog, I2C, pin control/GPIO, and Ethernet clocks on R-Car
V4H
- Add SDHI, Timer (CMT/TMU), and SPI (MSIOF) clocks on R-Car S4-8
- Add I2C clocks and resets on RZ/V2M
- Document clock support for the RZ/Five SoC
- mux-variant clock using the table variant to select parents
- clock controller for the rv1126 soc
- conversion of rk3128 to yaml and relicensing of the yaml bindings
to gpl2+MIT (following dt-binding guildelines)
- Exynos7885: add FSYS, TREX and MFC clock controllers
- Exynos850: add IS and AUD (audio) clock controllers with bindings
- ExynosAutov9: add FSYS clock controllers with bindings
- ExynosAutov9: correct clock IDs in bindings of Peric 0 and 1 clock
controllers, due to duplicated entries. This is an acceptable ABI
break: recently developed/added platform so without legacies, acked
by known users/developers
- ExynosAutov9: add few missing Peric 0/1 gates
- ExynosAutov9: correct register offsets of few Peric 0/1 clocks
- Minor code improvements (use of_device_get_match_data() helper,
code style)
- Add Krzysztof Kozlowski as co-maintainer of Samsung SoC clocks, as
he already maintainers that architecture/platform
- Keep Qualcomm GDSCs enabled when PWRSTS_RET flag is there, solving
retention issues during suspend of USB on Qualcomm sc7180/sc7280
and SC8280XP
- Qualcomm SM6115 and QCM2260 are moved to reuse PLL configuration
- Qualcomm SDM660 SDCC1 moved to floor clk ops
- Support for the APCS PLLs for Qualcomm IPQ8064, IPQ8074 and IPQ6018
was added/fixed
- The Qualcomm MSM8996 CPU clocks are updated with support for ACD
- Support for Qualcomm SDM670 GCC and RPMh clks was added
- Transition to parent_data, parent_hws and use of ARRAY_SIZE() for
num_parents was done for many Qualcomm SoCs
- Support for per-reset defined delay on Qualcomm was introduced"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (283 commits)
clk: qcom: gcc-sm6375: Ensure unsigned long type
clk: qcom: gcc-sm6375: Remove unused variables
clk: qcom: kpss-xcc: convert to parent data API
clk: introduce (devm_)hw_register_mux_parent_data_table API
clk: allow building lan966x as a module
clk: clk-xgene: simplify if-if to if-else
clk: ast2600: BCLK comes from EPLL
clk: clocking-wizard: Depend on HAS_IOMEM
clk: clocking-wizard: Use dev_err_probe() helper
clk: nxp: fix typo in comment
clk: pxa: add a check for the return value of kzalloc()
clk: vc5: Add support for IDT/Renesas VersaClock 5P49V6975
dt-bindings: clock: vc5: Add 5P49V6975
clk: mvebu: armada-37xx-tbg: Remove the unneeded result variable
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
clk: Renesas versaclock7 ccf device driver
dt-bindings: Renesas versaclock7 device tree bindings
clk: ti: Balance of_node_get() calls for of_find_node_by_name()
clk: imx: scu: fix memleak on platform_device_add() fails
clk: vc5: Use regmap_{set,clear}_bits() where appropriate
...
Linus Torvalds [Sat, 8 Oct 2022 16:46:29 +0000 (09:46 -0700)]
Merge tag 'gpio-updates-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio updates from Bartosz Golaszewski:
"We have a single new driver, support for a bunch of new models,
improvements in drivers and core gpiolib code as well device-tree
bindings changes.
Summary:
New driver:
- IMX System Controller Unit GPIOs
GPIO core:
- add fdinfo output for the GPIO character device file descriptors
(allows user-space to determine which processes own which GPIO
lines)
- improvements to OF GPIO code
- new quirk for Asus UM325UAZ in gpiolib-acpi
- new quirk for Freescale SPI in gpiolib-of
Driver improvements:
- add a new macro that reduces the amount of boilerplate code in ISA
drivers and use it in relevant drivers
- support two new models in gpio-pca953x
- support new model in gpio-f7188x
- convert more drivers to use immutable irq chips
- other minor tweaks
Device-tree bindings:
- add DT bindings for gpio-imx-scu
- convert Xilinx GPIO bindings to YAML
- reference the properties from the SPI peripheral device-tree
bindings instead of providing custom ones in the GPIO controller
document
- add parsing of GPIO hog nodes to the DT bindings for gpio-mpfs-gpio
- relax the node name requirements in gpio-stmpe
- add new models for gpio-rcar and gpio-pxa95xx
- add a new vendor prefix: Diodes (for Diodes, Inc.)
Misc:
- pulled in the immutable branch from the x86 platform drivers tree
including support for a new simatic board that depends on GPIO
changes"
* tag 'gpio-updates-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (36 commits)
gpio: tc3589x: Make irqchip immutable
gpiolib: cdev: add fdinfo output for line request file descriptors
gpio: twl4030: Reorder functions which allows to drop a forward declaraion
gpiolib: fix OOB access in quirk callbacks
gpiolib: of: factor out conversion from OF flags
gpiolib: rework quirk handling in of_find_gpio()
gpiolib: of: make Freescale SPI quirk similar to all others
gpiolib: of: do not ignore requested index when applying quirks
gpio: ws16c48: Ensure number of irq matches number of base
gpio: 104-idio-16: Ensure number of irq matches number of base
gpio: 104-idi-48: Ensure number of irq matches number of base
gpio: 104-dio-48e: Ensure number of irq matches number of base
counter: 104-quad-8: Ensure number of irq matches number of base
isa: Introduce the module_isa_driver_with_irq helper macro
gpio: pca953x: Add support for PCAL6534
gpio: pca953x: Swap if statements to save later complexity
gpio: pca953x: Fix pca953x_gpio_set_pull_up_down()
dt-bindings: gpio: pca95xx: add entry for pcal6534 and PI4IOE5V6534Q
dt-bindings: vendor-prefixes: add Diodes
gpio: mt7621: Switch to use platform_get_irq() function
...
Linus Torvalds [Sat, 8 Oct 2022 16:19:24 +0000 (09:19 -0700)]
Merge tag 'staging-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the large set of staging driver changes for 6.1-rc1.
Nothing really interesting in here at all except we deleted a driver
(fwserial) as no one had been using it for a long time. Other than
that, just the normal cleanups and minor fixes:
- rtl8723bs driver cleanups
- loads of r8188eu driver cleanups, making the driver smaller and
fixing up some firmware dependency issues.
- vt6655 driver cleanups.
- lots of other small staging driver cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (266 commits)
staging: rtl8192e: Rename variable Bandwidth to avoid CamelCase
staging: r8188eu: remove PHY_RFConfig8188E()
staging: r8188eu: remove PHY_RF6052_Config8188E()
staging: r8188eu: convert ODM_ReadAndConfig_AGC_TAB_1T_8188E() to int
staging: r8188eu: convert ODM_ReadAndConfig_PHY_REG_1T_8188E() to int
staging: r8188eu: convert ODM_ReadAndConfig_RadioA_1T_8188E() to int
staging: r8188eu: convert ODM_ReadAndConfig_MAC_REG_8188E() to int
staging: rtl8192e: cmdpkt: Use skb_put_data() instead of skb_put/memcpy pair
staging: r8188eu: Use skb_put_data() instead of skb_put/memcpy pair
staging: r8188eu: remove hal/odm_RegConfig8188E.c
staging: r8188eu: make odm_ConfigRF_RadioA_8188E() static
staging: r8188eu: make odm_ConfigMAC_8188E() static
staging: r8188eu: don't check for stop/removal in the blink worker
staging: r8188eu: don't check bSurpriseRemoved in SwLedOff
staging: rtl8192e: Remove unused variables ForcedAMSDUMaxSize, ...
staging: rtl8192e: Rename CurrentMPDU..., ForcedAMPDU... and ForcedMPDU...
staging: rtl8192e: Rename SelfMimoPs, CurrentOpMode and bForcedShortGI
staging: rtl8192e: Rename PeerMimoPs, IOTAction and IOTRaFunc
staging: rtl8192e: Rename RxRe...WinSize, RxReorder... and RxReorderDr...
staging: rtl8192e: Rename szRT2RTAggBuffer, bRegRxRe... and bCurRxReo...
...
Linus Torvalds [Sat, 8 Oct 2022 15:56:37 +0000 (08:56 -0700)]
Merge tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
fbdev: mb862xx: Fix check of return value from irq_of_parse_and_map()
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
This patch adds missing MODULE_DEVICE_TABLE definition
which generates correct modalias for automatic loading
of this driver when it is built as an external module.
The driver core supports the ability to handle the creation and removal
of device-specific sysfs files in a race-free manner. Moreover, it can
guarantee the success of creation. Therefore, it should be better to
convert to use dev_groups.
Coccinelle reports: WARNING: use scnprintf or sprintf
Adding to that, there has also been some slow migration from snprintf to
scnprintf. This article explains the rationale for this change:
https: //lwn.net/Articles/69419/
Colin Ian King [Wed, 7 Sep 2022 13:50:56 +0000 (14:50 +0100)]
fbdev: udlfb: Remove redundant initialization to variable identical
The variable identical is being initialized with a value that is never
read. The variable is being re-assigned later on. The initialization is
redundant and can be removed.
Cleans up clang scan-build warning:
drivers/video/fbdev/udlfb.c:373:6: warning: Value stored to 'identical'
during its initialization is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Helge Deller <deller@gmx.de>
cifs: secmech: use shash_desc directly, remove sdesc
The struct sdesc is just a wrapper around shash_desc, with exact same
memory layout. Replace the hashing TFMs with shash_desc as it's what's
passed to the crypto API anyway.
Also remove the crypto_shash pointers as they can be accessed via
shash_desc->tfm (and are actually only used in the setkey calls).
Adapt cifs_{alloc,free}_hash functions to this change.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
Enzo Matsumiya [Wed, 5 Oct 2022 07:42:07 +0000 (02:42 -0500)]
smb3: rename encryption/decryption TFMs
Detach the TFM name from a specific algorithm (AES-CCM) as
AES-GCM is also supported, making the name misleading.
s/ccmaesencrypt/enc/
s/ccmaesdecrypt/dec/
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
cifs: replace kfree() with kfree_sensitive() for sensitive data
Replace kfree with kfree_sensitive, or prepend memzero_explicit() in
other cases, when freeing sensitive material that could still be left
in memory.
Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Reported-by: kernel test robot <oliver.sang@intel.com> Link: https://lore.kernel.org/r/202209201529.ec633796-oliver.sang@intel.com Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Linus Torvalds [Sat, 8 Oct 2022 00:04:10 +0000 (17:04 -0700)]
Merge tag 'driver-core-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core and debug printk changes for
6.1-rc1. Included in here is:
- dynamic debug updates for the core and the drm subsystem. The drm
changes have all been acked by the relevant maintainers
- kernfs fixes for syzbot reported problems
- kernfs refactors and updates for cgroup requirements
- magic number cleanups and removals from the kernel tree (they were
not being used and they really did not actually do anything)
- other tiny cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (74 commits)
docs: filesystems: sysfs: Make text and code for ->show() consistent
Documentation: NBD_REQUEST_MAGIC isn't a magic number
a.out: restore CMAGIC
device property: Add const qualifier to device_get_match_data() parameter
drm_print: add _ddebug descriptor to drm_*dbg prototypes
drm_print: prefer bare printk KERN_DEBUG on generic fn
drm_print: optimize drm_debug_enabled for jump-label
drm-print: add drm_dbg_driver to improve namespace symmetry
drm-print.h: include dyndbg header
drm_print: wrap drm_*_dbg in dyndbg descriptor factory macro
drm_print: interpose drm_*dbg with forwarding macros
drm: POC drm on dyndbg - use in core, 2 helpers, 3 drivers.
drm_print: condense enum drm_debug_category
debugfs: use DEFINE_SHOW_ATTRIBUTE to define debugfs_regset32_fops
driver core: use IS_ERR_OR_NULL() helper in device_create_groups_vargs()
Documentation: ENI155_MAGIC isn't a magic number
Documentation: NBD_REPLY_MAGIC isn't a magic number
nbd: remove define-only NBD_MAGIC, previously magic number
Documentation: FW_HEADER_MAGIC isn't a magic number
Documentation: EEPROM_MAGIC_VALUE isn't a magic number
...
The background is that we use dpu in cloud computing,the arch is x86,80
cores. We will have a lots of virtio devices,like 512 or more.
When we probe about 200 virtio_blk devices,it will fail and
the stack is printed as follows:
The log :
"genirq: Flags mismatch irq 0. 00000080 (virtio418) vs. 00015a00 (timer)"
was printed because of the irq 0 is used by timer exclusive,and when
vp_find_vqs call vp_find_vqs_msix and returns false twice (for
whatever reason), then it will call vp_find_vqs_intx as a fallback.
Because vp_dev->pci_dev->irq is zero, we request irq 0 with
flag IRQF_SHARED, and get a backtrace like above.
According to PCI spec about "Interrupt Pin" Register (Offset 3Dh):
"The Interrupt Pin register is a read-only register that identifies the
legacy interrupt Message(s) the Function uses. Valid values are 01h, 02h,
03h, and 04h that map to legacy interrupt Messages for INTA,
INTB, INTC, and INTD respectively. A value of 00h indicates that the
Function uses no legacy interrupt Message(s)."
So if vp_dev->pci_dev->pin is zero, we should not request legacy
interrupt.
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com> Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220930000915.548-1-angus.chen@jaguarmicro.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vDPA: conditionally read MTU and MAC in dev cfg space
The spec says:
mtu only exists if VIRTIO_NET_F_MTU is set
The mac address field always exists (though
is only valid if VIRTIO_NET_F_MAC is set)
So vdpa_dev_net_config_fill() should read MTU and MAC
conditionally on the feature bits.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com> Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220929014555.112323-7-lingshan.zhu@intel.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vDPA: fix spars cast warning in vdpa_dev_net_mq_config_fill
This commit fixes spars warnings: cast to restricted __le16
in function vdpa_dev_net_mq_config_fill()
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com> Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220929014555.112323-6-lingshan.zhu@intel.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vdpa_dev_net_mq_config_fill() should checks device features
for MQ than driver features.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com> Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220929014555.112323-5-lingshan.zhu@intel.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vDPA: check VIRTIO_NET_F_RSS for max_virtqueue_paris's presence
virtio 1.2 spec says:
max_virtqueue_pairs only exists if VIRTIO_NET_F_MQ or
VIRTIO_NET_F_RSS is set.
So when reporint MQ to userspace, it should check both
VIRTIO_NET_F_MQ and VIRTIO_NET_F_RSS.
unused parameter struct vdpa_device *vdev is removed
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com> Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220929014555.112323-4-lingshan.zhu@intel.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vDPA: allow userspace to query features of a vDPA device
This commit adds a new vDPA netlink attribution
VDPA_ATTR_VDPA_DEV_SUPPORTED_FEATURES. Userspace can query
features of vDPA devices through this new attr.
This commit invokes vdpa_config_ops.get_config()
rather than vdpa_get_config_unlocked() to read
the device config spcae, so no races in
vdpa_set_features_unlocked()
Userspace tool iproute2 example:
$ vdpa dev config show vdpa0
vdpa0: mac 00:e8:ca:11:be:05 link up link_announce false max_vq_pairs 4 mtu 1500
negotiated_features MRG_RXBUF CTRL_VQ MQ VERSION_1 ACCESS_PLATFORM
dev_features MTU MAC MRG_RXBUF CTRL_VQ MQ ANY_LAYOUT VERSION_1 ACCESS_PLATFORM
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20220929014555.112323-2-lingshan.zhu@intel.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Linus Torvalds [Fri, 7 Oct 2022 23:48:26 +0000 (16:48 -0700)]
Merge tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver changes for 6.1-rc1.
Nothing major in here, lots of little things with new devices
supported and updates for a few drivers. Highlights include:
- thunderbolt/USB4 devices supported a bit better than before, and
some new ids to enable new hardware devices
- USB gadget uvc updates for newer video formats and better v4l
integration (the v4l portions were acked by those maintainers)
- typec updates for tiny issues and more typec drivers for new chips.
- xhci tiny updates for minor issues
- big usb-serial ftdi_sio driver update to handle new devices better
- lots of tiny dwc3 fixes and updates for the IP block that is
showing up everywhere these days
- dts updates for new devices being supported
- other tiny janitorial and cleanups fixes for lots of different USB
drivers. Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
usb: gadget: uvc: don't put item still in use
usb: gadget: uvc: Fix argument to sizeof() in uvc_register_video()
usb: host: ehci-exynos: switch to using gpiod API
Revert "usb: dwc3: Don't switch OTG -> peripheral if extcon is present"
Revert "USB: fixup for merge issue with "usb: dwc3: Don't switch OTG -> peripheral if extcon is present""
dt-bindings: usb: Convert FOTG210 to dt schema
usb: mtu3: fix failed runtime suspend in host only mode
USB: omap_udc: Fix spelling mistake: "tranceiver_ctrl" -> "transceiver_ctrl"
usb: typec: ucsi_ccg: Disable UCSI ALT support on Tegra
usb: typec: Replace custom implementation of device_match_fwnode()
usb: typec: ucsi: Don't warn on probe deferral
usb: add quirks for Lenovo OneLink+ Dock
MAINTAINERS: switch dwc3 to Thinh
usb: idmouse: fix an uninit-value in idmouse_open
USB: PHY: JZ4770: Switch to use dev_err_probe() helper
usb: phy: generic: Switch to use dev_err_probe() helper
usb: ulpi: use DEFINE_SHOW_ATTRIBUTE to simplify ulpi_regs
usb: cdns3: remove dead code
usb: cdc-wdm: Use skb_put_data() instead of skb_put/memcpy pair
usb: musb: sunxi: Switch to use dev_err_probe() helper
...
Linus Torvalds [Fri, 7 Oct 2022 23:36:24 +0000 (16:36 -0700)]
Merge tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to finally get
this work done
- tty serial transmit cleanups in various drivers in preparation for
more cleanup and unification in future releases (that work was not
ready for this release)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full details in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (102 commits)
serial: cpm_uart: Don't request IRQ too early for console port
tty: serial: do unlock on a common path in altera_jtaguart_console_putc()
tty: serial: unify TX space reads under altera_jtaguart_tx_space()
tty: serial: use FIELD_GET() in lqasc_tx_ready()
tty: serial: extend lqasc_tx_ready() to lqasc_console_putchar()
tty: serial: allow pxa.c to be COMPILE_TESTed
serial: stm32: Fix unused-variable warning
tty: serial: atmel: Add COMMON_CLK dependency to SERIAL_ATMEL
serial: 8250: Fix restoring termios speed after suspend
serial: Deassert Transmit Enable on probe in driver-specific way
serial: 8250_dma: Convert to use uart_xmit_advance()
serial: 8250_omap: Convert to use uart_xmit_advance()
MAINTAINERS: Solve warning regarding inexistent atmel-usart binding
serial: stm32: Deassert Transmit Enable on ->rs485_config()
serial: ar933x: Deassert Transmit Enable on ->rs485_config()
tty: serial: atmel: Use FIELD_PREP/FIELD_GET
tty: serial: atmel: Make the driver aware of the existence of GCLK
tty: serial: atmel: Only divide Clock Divisor if the IP is USART
tty: serial: atmel: Separate mode clearing between UART and USART
dt-bindings: serial: atmel,at91-usart: Add gclk as a possible USART clock
...
Linus Torvalds [Fri, 7 Oct 2022 23:13:55 +0000 (16:13 -0700)]
Merge tag 'soundwire-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire updates from Vinod Koul:
"Updates for Intel, Cadence and Qualcomm drivers:
- another round of Intel driver cleanup to prepare for future code
reorg which is expected in next cycle (Pierre-Louis Bossart)
- bus unattach notifications processing during re-enumeration along
with Cadence driver updates for this (Richard Fitzgerald)
- Qualcomm driver updates to handle device0 status (Srinivas
Kandagatla)"
* tag 'soundwire-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (42 commits)
soundwire: intel: add helper to stop bus
soundwire: intel: introduce helpers to start bus
soundwire: intel: introduce intel_shim_check_wake() helper
soundwire: intel: simplify read ops assignment
soundwire: intel: remove intel_init() wrapper
soundwire: intel: move shim initialization before power up/down
soundwire: intel: remove clock_stop parameter in intel_shim_init()
soundwire: intel: move all PDI initialization under intel_register_dai()
soundwire: intel: move DAI registration and debugfs init earlier
soundwire: intel: simplify flow and use devm_ for DAI registration
soundwire: intel: fix error handling on dai registration issues
soundwire: cadence: Simplify error paths in cdns_xfer_msg()
soundwire: cadence: Fix error check in cdns_xfer_msg()
soundwire: cadence: Write to correct address for each FIFO chunk
soundwire: bus: Fix wrong port number in sdw_handle_slave_alerts()
soundwire: qcom: do not send status of device 0 during alert
soundwire: qcom: update status from device id 1
soundwire: cadence: Don't overwrite msg->buf during write commands
soundwire: bus: Don't exit early if no device IDs were programmed
soundwire: cadence: Fix lost ATTACHED interrupts when enumerating
...
projects / kernel.git / log