Quanyang Wang [Wed, 10 Mar 2021 04:59:45 +0000 (12:59 +0800)]
drm: xlnx: zynqmp_dpsub: Call pm_runtime_get_sync before setting pixel clock
The Runtime PM subsystem will force the device "fd4a0000.zynqmp-display"
to enter suspend state while booting if the following conditions are met:
- the usage counter is zero (pm_runtime_get_sync hasn't been called yet)
- no 'active' children (no zynqmp-dp-snd-xx node under dpsub node)
- no other device in the same power domain (dpdma node has no
"power-domains = <&zynqmp_firmware PD_DP>" property)
So there is a scenario as below:
1) DP device enters suspend state <- call zynqmp_gpd_power_off
2) zynqmp_disp_crtc_setup_clock <- configurate register VPLL_FRAC_CFG
3) pm_runtime_get_sync <- call zynqmp_gpd_power_on and clear previous
VPLL_FRAC_CFG configuration
4) clk_prepare_enable(disp->pclk) <- enable failed since VPLL_FRAC_CFG
configuration is corrupted
From above, we can see that pm_runtime_get_sync may clear register
VPLL_FRAC_CFG configuration and result the failure of clk enabling.
Putting pm_runtime_get_sync at the very beginning of the function
zynqmp_disp_crtc_atomic_enable can resolve this issue.
Dave Airlie [Thu, 5 Aug 2021 20:55:58 +0000 (06:55 +1000)]
Merge tag 'drm-misc-next-2021-08-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- Assorted docbook updates.
- Unbreak damage selftests.
- Define DRM_FORMAT_MAX_PLANES, maximum planes for a planar format.
- Add gem fb vmap/vunmap helpers, use them in gud and vkms drivers.
Driver Changes:
- Bridge fixes for ti-sn65dsi86.
- Use a full-featured driver for ATNA33XC20 to get backlight right,
instead of the simple panel driver.
- Assorted fixes to pl111,.
- Support E Ink VB3300-KCA panel.
- Add support for Gopher 2b LCD and ilitek ili9341 panels.
Dillon Min [Sat, 24 Jul 2021 03:44:03 +0000 (11:44 +0800)]
drm/panel: Add ilitek ili9341 panel driver
This driver combines tiny/ili9341.c mipi_dbi_interface driver
with mipi_dpi_interface driver, can support ili9341 with serial
mode and parallel rgb interface mode by different dts bindings.
Artjom Vejsel [Wed, 4 Aug 2021 00:23:53 +0000 (03:23 +0300)]
drm/panel-simple: add Gopher 2b LCD panel
The Gopher 2b LCD panel is used in Gopher 2b handhelds.
It's simple panel with NewVision NV3047 driver, but SPI lines are not
connected. It has no specific name, since it's unique to that handheld.
lot name at AliExpress: 4.3 inch 40PIN TFT LCD Screen COG NV3047 Drive
IC 480(RGB)*272 No Touch 24Bit RGB Interface
drm/vkms: Map output framebuffer BOs with drm_gem_fb_vmap()
Abstract the framebuffer details by mappings its BOs with a call
to drm_gem_fb_vmap(). Unmap with drm_gem_fb_vunamp().
Before, the output address with stored as raw pointer in the priv
field of struct drm_writeback_job. Introduce the new type
struct vkms_writeback_job, which holds the output mappings addresses
while the writeback job is active.
The patchset also cleans up some internal casting an setup of the
output addresses. No functional changes.
v3:
* free instances of struct vkms_writeback_job on cleanup
or errors
drm/gem: Clear mapping addresses for unused framebuffer planes
Set the returned mapping address to NULL if a framebuffer plane does
not have a BO associated with it. Likewise, ignore mappings of NULL
during framebuffer unmap operations. Allows users of the functions to
perform unmap operations of certain BOs by themselfes.
Move framebuffer vmap code from shadow-buffered plane state into the new
interfaces drm_gem_fb_vmap() and drm_gem_fb_vunmap(). These functions
provide mappings of a framebuffer's BOs into kernel address space. No
functional changes.
v4:
* remove duplicated blank line
v2:
* using [static N] for array parameters enables compile-time checks
* include <drm/drm_fourcc.h> for DRM_FORMAT_MAX_PLANES (kernel
test robot)
DRM uses a magic number of 4 for the maximum number of planes per color
format. Declare this constant via DRM_FORMAT_MAX_PLANES and update the
related code. Some code depends on the length of arrays that are now
declared with DRM_FORMAT_MAX_PLANES. Convert it from '4' to ARRAY_SIZE.
v2:
* mention usage of ARRAY_SIZE() in the commit message (Maxime)
* also fix error handling in drm_gem_fb_init_with_funcs()
(kernel test robot)
* include <drm/drm_fourcc.h> for DRM_FORMAT_MAX_PLANES
Simon Ser [Mon, 2 Aug 2021 07:28:35 +0000 (07:28 +0000)]
drm: document drm_mode_get_property
It's not obvious what the fields mean and how they should be used.
The most important detail is the link to drm_property.flags, which
describes how property types work.
v2: document enum drm_mode_property_enum, add ref to "Modeset Base
Object Abstraction" (Daniel)
Daniel Vetter [Fri, 30 Jul 2021 09:52:51 +0000 (11:52 +0200)]
drm: Fix oops in damage self-tests by mocking damage property
I've added a new check to make sure that drivers which insepct the
damage property have it set up correctly, but somehow missed that this
borke the damage selftest in the CI result noise.
Fix it up by mocking enough of drm_device and drm_plane so we can call
drm_plane_enable_fb_damage_clips() to make the new check happy.
Since there's a lot of duplicated mock code already copy-pasted into
each test I've also refactored this a bit to trim it down.
v2: Squash in fixup from 0day for
drivers/gpu/drm/selftests/test-drm_damage_helper.c:15:19: warning: symbol 'mock_device' was not declared. Should it be static?
drivers/gpu/drm/selftests/test-drm_damage_helper.c:16:30: warning: symbol 'mock_obj_props' was not declared. Should it be static?
drivers/gpu/drm/selftests/test-drm_damage_helper.c:17:18: warning: symbol 'mock_plane' was not declared. Should it be static?
drivers/gpu/drm/selftests/test-drm_damage_helper.c:18:21: warning: symbol 'mock_prop' was not declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: kernel test robot <lkp@intel.com> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Fixes: c7fcbf251397 ("drm/plane: check that fb_damage is set up when used") Cc: José Roberto de Souza <jose.souza@intel.com> (v1) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210730095251.4343-1-daniel.vetter@ffwll.ch Link: https://patchwork.freedesktop.org/patch/msgid/20210730141948.GA11955@243d74413310
Gregory Williams [Sat, 31 Jul 2021 00:53:28 +0000 (20:53 -0400)]
DRM: ast: Fixed coding style issues of ast_mode.c
Removed space before comma, fixed if statements by putting trailing
statements on new line, fixed unsigned int declaration, and removed
not needed else statement after return.
Douglas Anderson [Fri, 30 Jul 2021 15:46:05 +0000 (08:46 -0700)]
drm/panel: atna33xc20: Introduce the Samsung ATNA33XC20 panel
The Samsung ATNA33XC20 panel is an AMOLED eDP panel that has backlight
control over the DP AUX channel.
This panel is _almost_ able to be controlled in a "simple" way (and it
originally was implemented in panel-simple.c), but it's really
impossible to get the backlight semantics right there without adding
wacky special-case code to panel-simple. Let's give up and clone the
parts of panel-simple that we need and implement the power sequence
that this panel needs.
NOTE: we'll still leave the devicetree bindings alone. Even though the
power-sequencing is non-standard the bindings are still "simple".
Those delays were added to support the Samsung ATNA33XC20
panel. However, we've moving that to its own panel driver and out of
panel-simple. That means we don't need the ability to specify this
delay.
NOTE: it's unlikely we want to keep this delay "just in case" some
other panel needs it. The enable-gpio and the power supply are really
supposed to be different ways to specify the same thing: the main
enable of the panel. Supporting a delay between them doesn't really
make sense.
This panel's power sequencing really can't be handled properly by
panel-simple because of the special sequencing needed for the EL_ON3
GPIO. The only way it was sorta working in the past was by trying to
jam that signal into the "enable-gpio", but that really wasn't a good
fit. We'll add a custom panel driver for this panel to do it right.
Douglas Anderson [Fri, 30 Jul 2021 15:46:02 +0000 (08:46 -0700)]
drm/bridge: ti-sn65dsi86: Add some 100 us delays
The manual has always said that we need 100 us delays in a few
places. Though it hasn't seemed to be a big deal to skip these, let's
add them in case it makes something happier.
NOTE: this fixes no known issues but it seems good to make it right.
Douglas Anderson [Fri, 30 Jul 2021 15:46:01 +0000 (08:46 -0700)]
drm/bridge: ti-sn65dsi86: Fix power off sequence
When testing with a panel that's apparently a little more persnickety
about the correct power sequence (specifically Samsung ATNA33XC20), we
found that the ti-sn65dsi86 was doing things just slightly wrong.
Looking closely at the ti-sn65dsi86's datasheet, the power off
sequence is supposed to be:
1. Clear VSTREAM_ENABLE bit
2. Stop DSI stream from GPU. DSI lanes must be placed in LP11 state.
3. Program the ML_TX_MODE to 0x0 (OFF)
4. Program the DP_NUM_LANES register to 0x0
5. Clear the DP_PLL_EN bit.
6. Deassert the EN pin.
7. Remove power from supply pins
Since we were doing the whole sequence in the "disable", I believe
that step #2 (stopping the DSI stream from the GPU) wasn't
happening. We also weren't setting DP_NUM_LANES to 0.
Let's fix this.
NOTE: things are a little asymmetric now. For instance, we turn the
PLL on in "enable" but now we're not turning it off until
"post_disable". It would seem to make sense to move the PLL turning on
to "pre_enable" to match. Unfortunately, I don't believe that's
allowed. It looks as if (in the non-refclk mode which probably nobody
is using) we have to wait until the MIPI clock is there before we can
enable the PLL. In any case, the way it is here won't really
hurt--it'll just leave the PLL on a little longer.
Douglas Anderson [Fri, 30 Jul 2021 15:46:00 +0000 (08:46 -0700)]
drm/dp: Don't zero PWMGEN_BIT_COUNT when driver_pwm_freq_hz not specified
The function drm_edp_backlight_init() is defined such that the
"driver_pwm_freq_hz" parameter is optional--it's 0 if you don't want
to futz with it. If you follow this variable through, you'll find out
that if it's 0 we won't ever set the "bl->pwmgen_bit_count", leaving
it as 0.
That means that before using it in drm_edp_backlight_enable() we need
to check to see if it's non-zero.
Programming this field to zero was confusing the panel I tested with
(Samsung ATNA33XC20). The backlight still worked somewhat but the
brightness values didn't correspond to what they should have been.
The kerneldoc in drm_lease.c is unused because none of the functions
are driver interfaces as the symbols are not exported.
Since they aren't used and much of the existing comments don't provide
any insights (e.g. they just repeat the function name or list out the
function parameters), they should be removed to make them easier to
maintain and to make useful info more obvious.
As a note, many of the comments mention whether idr_mutex should be
held, but these are mostly redundant in cases where the function
contains lockdep assertions or grabs the mutex.
To simplify review, here's the reasoning behind each update.
drm_lease_owner:
function name is self-descriptive
_drm_find_lessee:
function name is self-descriptive
_drm_lease_held_master:
function name and signature are self-descriptive
_drm_has_leased:
kerneldoc is summarized into a comment because the function name could
be interpreted ambiguously (check if the object has been leased VS
check if the master has a lease on the object)
_drm_lease_held:
Retain the idr_mutex comment because the function does not directly
grab the mutex or use a lockdep assertion.
Otherwise, the function name is self-descriptive.
drm_lease_held:
function name is self-descriptive
drm_lease_filter_crtcs:
Kerneldoc is summarized into a comment because the function name could
be interpreted ambiguously (filter leases based on crtcs mask VS
filter crtcs mask based on leases)
drm_lease_create:
Kerneldoc removed.
Useful function details such as atomic leasing are retained.
Errno interpretations are useful and retained.
drm_lease_destroy:
function name is self-descriptive. Additional information is also
removed as they're already present as comments inside the function.
_drm_lease_revoke:
function name is self-descriptive
drm_lease_revoke:
function name is self-descriptive
drm_mode_create_lease_ioctl:
Kerneldoc removed, but useful function details retained.
drm_mode_list_lessees_ioctl:
function name is self-descriptive. Additional details restate what the
code does.
drm_mode_get_lease_ioctl:
Function summary retained to clarify that it's the leased objects that
are returned, not the lease structure.
drm_mode_revoke_lease_ioctl:
Kerneldoc removed, but useful function details retained.
Dave Airlie [Fri, 30 Jul 2021 06:05:58 +0000 (16:05 +1000)]
Merge tag 'drm-msm-next-2021-07-28' of https://gitlab.freedesktop.org/drm/msm into drm-next
An early pull for v5.15 (there'll be more coming in a week or two),
consisting of the drm/scheduler conversion and a couple other small
series that one was based one. Mostly sending this now because IIUC
danvet wanted it in drm-next so he could rebase on it. (Daniel, if
you disagree then speak up, and I'll instead include this in the main
pull request once that is ready.)
This also has a core patch to drop drm_gem_object_put_locked() now
that the last use of it is removed.
Dave Airlie [Fri, 30 Jul 2021 04:51:22 +0000 (14:51 +1000)]
Merge tag 'drm-misc-next-2021-07-29' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
- Add modifiers for arm fixed rate compression.
Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.
Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.
Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.
Maxime Ripard [Wed, 7 Jul 2021 09:36:32 +0000 (11:36 +0200)]
drm/vc4: hdmi: Remove unused struct
Commit 91e99e113929 ("drm/vc4: hdmi: Register HDMI codec") removed the
references to the vc4_hdmi_audio_component_drv structure, but not the
structure itself resulting in a warning. Remove it.
Maxime Ripard [Wed, 7 Jul 2021 09:36:31 +0000 (11:36 +0200)]
drm/vc4: hdmi: Remove redundant variables
The vc4_hdmi_audio_prepare function and the functions it's calling have
in several occurences multiple dereferences of either the sample rate or
the number of channels.
It turns out that these variables are also passed through the hdmi codec
parameters structure. Convert all the users to use this structure, and
if it's used multiple times use a variable to store it instead of
dereferencing it every time.
We make the following changes to the documentation of drm leases to
make it easier to reason about their usage. In particular, we clarify
the lifetime and locking rules of lease fields in drm_master:
1. Make it clear that &drm_device.mode_config.idr_mutex protects the
lease idr and list structures for drm_master. The lessor field itself
doesn't need to be protected as it doesn't change after it's set in
drm_lease_create.
2. Add descriptions for the lifetime of lessors and leases.
3. Add an overview DOC: section in drm-uapi.rst that defines the
terminology for drm leasing, and explains how leases work and why
they're used.
Fix a bug in smu_cmn_send_msg_without_waiting() in
that this function does not need to take the
smu->message_lock mutex in order to send a message
down to the SMU. The mutex is acquired by the
caller of this function instead.
Cc: Alex Deucher <Alexander.Deucher@amd.com> Cc: Changfeng Zhu <Changfeng.Zhu@amd.com> Cc: Huang Rui <ray.huang@amd.com> Fixes: 5810323ba69289 ("drm/amd/pm: Fix a bug communicating with the SMU (v5)") Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fence driver was enabled per ring when sw init on per IP block before.
Change to enable all the fence driver at the same time after
amdgpu_device_ip_init finished.
Rename some function related to fence to make it reasonable for read.
Alex Deucher [Thu, 8 Jul 2021 20:31:10 +0000 (16:31 -0400)]
drm/amdgpu/display: add support for multiple backlights
On platforms that support multiple backlights, register
each one separately. This lets us manage them independently
rather than registering a single backlight and applying the
same settings to both.
v2: fix typo: Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Roman Li <Roman.Li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This converts the internal backlight in the Sony ACX424AKP
driver to do it the canonical way:
- Assign the panel->backlight during probe.
- Let the panel framework handle the backlight.
- Make the backlight .set_brightness() turn the backlight
off completely if blank.
- Fix some dev_err_probe() use cases along the way.
Inside drm_is_current_master, using the outer drm_device.master_mutex
to protect reads of drm_file.master makes the function prone to creating
lock hierarchy inversions. Instead, we can use the
drm_file.master_lookup_lock that sits at the bottom of the lock
hierarchy.
Simon Ser [Sun, 25 Jul 2021 16:49:01 +0000 (16:49 +0000)]
maintainers: add bugs and chat URLs for amdgpu
Add links to the issue tracker and the IRC channel for the amdgpu
driver.
Signed-off-by: Simon Ser <contact@emersion.fr> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Christian König <christian.koenig@amd.com> Cc: Pan Xinhui <Xinhui.Pan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Only set default brightness for OLED
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Camille Cho <Camille.Cho@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes some other code to only use aux for backlight control on
OLED panels. The commit message seems to indicate that PWM should
be used for SDR mode on HDR panels. Do something similar for
backlight control in general. This may need to be revisited if and
when HDR started to get used.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1438
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213715 Reviewed-by: Roman Li <Roman.Li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Evan Quan [Wed, 21 Jul 2021 10:19:38 +0000 (18:19 +0800)]
drm/amd/pm: restore user customized OD settings properly for NV1x
The customized OD settings can be divided into two parts: those
committed ones and non-committed ones.
- For those changes which had been fed to SMU before S3/S4/Runpm
suspend kicked, they are committed changes. They should be properly
restored and fed to SMU on S3/S4/Runpm resume.
- For those non-committed changes, they are restored only without feeding
to SMU.
Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixed:
- Guard DST_Y_PREFETCH register overflow in DCN21
- Add missing DCN21 IP parameter
- Fix PSR command version
- Add ETW logging for AUX failures
- Add ETW log to dmub_psr_get_state
- Fixed EdidUtility build errors
- Fix missing reg offset for the dmcub test debug registers
- Adding update authentication interface
- Remove unused functions of opm state query support
- Always wait for update lock status
- Refactor riommu invalidation wa
- Ensure dentist display clock update finished in DCN20
Reviewed-by: Hsieh Mike <Mike.Hsieh@amd.com> Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Aric Cyr <aric.cyr@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: ensure dentist display clock update finished in DCN20
[Why]
We don't check DENTIST_DISPCLK_CHG_DONE to ensure dentist
display clockis updated to target value. In some scenarios with large
display clock margin, it will deliver unfinished display clock and cause
issues like display black screen.
[How]
Checking DENTIST_DISPCLK_CHG_DONE to ensure display clock
has been update to target value before driver do other clock related
actions.
Reviewed-by: Cyr Aric <aric.cyr@amd.com> Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Dale Zhao <dale.zhao@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Fri, 9 Jul 2021 21:47:39 +0000 (17:47 -0400)]
drm/amd/display: refactor riommu invalidation wa
[Why]
A cleaner solution, only done once on boot.
[How]
Remove previous workaround and configure an extra
vmid one time on boot
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com> Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Wenjing Liu [Thu, 15 Jul 2021 18:55:28 +0000 (14:55 -0400)]
drm/amd/display: remove unused functions
[why]
It has been decided that opm state query support will be dropped.
Therefore link encryption enabled and save current encryption states
won't be used anymore and there are no foreseeable usages in the future.
We will remove these two interfaces for clean up.
Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previously to toggle authentication, we need to remove and
add the same display back with modified adjustment.
This method will toggle DTM state without actual hardware changes.
This is not per design and would cause potential issues in the long run.
[how]
We are creating a dedicated interface that does the same thing as
remove and add back the display without changing DTM state.
Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Eric Yang [Fri, 9 Jul 2021 21:11:34 +0000 (17:11 -0400)]
drm/amd/display: fix missing reg offset
[Why]
Initializing was missing reg offsets for the dmcub test debug registers
causing assert
[How]
Add initialization
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com> Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark Morra [Mon, 28 Jun 2021 22:00:30 +0000 (18:00 -0400)]
drm/amd/display: Fixed EdidUtility build errors
[HOW]
Added #ifdefs and refactored various parts of dc to
allow dc_link to be built by AMD EDID UTILITY
[WHY]
dc_dsc was refactored moving some of the code that AMD EDID UTILITY needed
to dc_link, so now dc_link needs to be included by AMD EDID UTILITY
Squash in DCN config fix (Alex)
Reviewed-by: Leung Martin <Martin.Leung@amd.com> Acked-by: Solomon Chiu <solomon.chiu@amd.com> Signed-off-by: Mark Morra <MarkAlbert.Morra@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/vmwgfx: Be a lot more flexible with MOB limits
The code was trying to keep a strict limit on the amount of mob
memory that was used in the guest by making it match the host
settings. There's technically no reason to do that (guests can
certainly use more than the host can have resident in renderers
at the same time).
In particular this is problematic because our userspace is not
great at handling OOM conditions and running out of MOB space
results in GL apps crashing, e.g. gnome-shell likes to allocate
huge surfaces (~61MB for the desktop on 2560x1600 with two workspaces)
and running out of memory there means that the gnome-shell crashes
on startup taking us back to the login and resulting in a system
where one can not login in graphically anymore.
Instead of letting the userspace crash we can extend available
MOB space, we just don't want to use all of the RAM for graphics,
so we're going to limit it to half of RAM.
With the addition of some extra logging this should make the
"guest has been configured with not enough graphics memory"
errors a lot easier to diagnose in cases where the automatic
expansion of MOB space fails.
The code was using the old DRM logging functions, which made it
hard to figure out what was coming from vmwgfx. The newer logging
helpers include the driver name in the logs and make it explicit
which driver they're coming from. This allows us to standardize
our logging a bit and clean it up in the process.
vmwgfx is a little special because technically the hardware it's
running on can be anything from the last 12 years or so which is
why we need to include capabilities in the logs in the first
place or otherwise we'd have no way of knowing what were
the capabilities of the platform the guest was running in.
The macro has been accounting for DRM_COMMAND_BASE for a long time
now so there's no reason to still be duplicating it. Plus we were
leaving the name undefined which meant that all the DRM ioctl
warnings/errors were always listing "null" ioctl at the culprit.
This fixes the undefined ioctl name and removes duplicated code.
Rob Clark [Wed, 28 Jul 2021 01:06:18 +0000 (18:06 -0700)]
drm/msm/gem: Mark active before pinning
Mark all the bos in the submit as active, before pinning, to prevent
evicting a buffer in the same submit to make room for a buffer earlier
in the table.
Rob Clark [Wed, 28 Jul 2021 01:06:17 +0000 (18:06 -0700)]
drm/msm: Utilize gpu scheduler priorities
The drm/scheduler provides additional prioritization on top of that
provided by however many number of ringbuffers (each with their own
priority level) is supported on a given generation. Expose the
additional levels of priority to userspace and map the userspace
priority back to ring (first level of priority) and schedular priority
(additional priority levels within the ring).
Rob Clark [Wed, 28 Jul 2021 01:06:15 +0000 (18:06 -0700)]
drm/msm: Drop submit bo_list
This was only used to detect userspace including the same bo multiple
times in a submit. But ww_mutex can already tell us this.
When we drop struct_mutex around the submit ioctl, we'd otherwise need
to lock the bo before adding it to the bo_list. But since ww_mutex can
already tell us this, it is simpler just to remove the bo_list.
Rob Clark [Wed, 28 Jul 2021 01:06:14 +0000 (18:06 -0700)]
drm/msm: Conversion to drm scheduler
For existing adrenos, there is one or more ringbuffer, depending on
whether preemption is supported. When preemption is supported, each
ringbuffer has it's own priority. A submitqueue (which maps to a
gl context or vk queue in userspace) is mapped to a specific ring-
buffer at creation time, based on the submitqueue's priority.
Each ringbuffer has it's own drm_gpu_scheduler. Each submitqueue
maps to a drm_sched_entity. And each submit maps to a drm_sched_job.
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/4 Signed-off-by: Rob Clark <robdclark@chromium.org> Acked-by: Christian König <christian.koenig@amd.com> Link: https://lore.kernel.org/r/20210728010632.2633470-10-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org>
Laurent Pinchart [Mon, 25 May 2020 03:18:01 +0000 (06:18 +0300)]
drm: rcar-du: Use drm_bridge_connector_init() helper
Use the drm_bridge_connector_init() helper to create a drm_connector for
each output, instead of relying on the bridge drivers doing so. Attach
the bridges with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag to instruct
them not to create a connector.
drm: rcar-du: lvds: Convert to DRM panel bridge helper
Replace the manual panel handling with usage of the DRM panel bridge
helper. This simplifies the driver, and brings support for
DRM_BRIDGE_ATTACH_NO_CONNECTOR as an added bonus.
Laurent Pinchart [Thu, 14 May 2020 01:03:07 +0000 (04:03 +0300)]
drm: bridge: dw-hdmi: Attach to next bridge if available
On all platforms except i.MX and Rockchip, the dw-hdmi DT bindings
require a video output port connected to an HDMI sink (most likely an
HDMI connector, in rare cases another bridges converting HDMI to another
protocol). For those platforms, retrieve the next bridge and attach it
from the dw-hdmi bridge attach handler.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Laurent Pinchart [Tue, 23 Mar 2021 21:50:08 +0000 (23:50 +0200)]
drm/bridge: Centralize error message when bridge attach fails
Being informed of a failure to attach a bridge is useful, and many
drivers prints an error message in that case. Move the message to
drm_bridge_attach() to avoid code duplication.
Suggested-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Laurent Pinchart [Tue, 23 Mar 2021 00:09:53 +0000 (02:09 +0200)]
drm: rcar-du: Shutdown the display on remove
When the device is unbound from the driver (the DU being a platform
device, this occurs either when removing the DU module, or when
unbinding the device manually through sysfs), the display may be active.
Make sure it gets shut down.
Laurent Pinchart [Tue, 23 Mar 2021 00:09:53 +0000 (02:09 +0200)]
drm: rcar-du: Don't put reference to drm_device in rcar_du_remove()
The reference to the drm_device that was acquired by
devm_drm_dev_alloc() is released automatically by the devres
infrastructure. It must not be released manually, as that causes a
reference underflow..
Laurent Pinchart [Tue, 23 Mar 2021 00:09:53 +0000 (02:09 +0200)]
drm: rcar-du: Shutdown the display on system shutdown
When the system shuts down or warm reboots, the display may be active,
with the hardware accessing system memory. Upon reboot, the DDR will not
be accessible, which may cause issues.
Implement the platform_driver .shutdown() operation and shut down the
display to fix this.
Colin Ian King [Thu, 4 Feb 2021 18:33:44 +0000 (18:33 +0000)]
drm/bridge: make a const array static, makes object smaller
Don't populate the const array frs_limits on the stack but instead make
it static. Makes the object code smaller by 128 bytes:
Before:
text data bss dec hex filename
24845 7440 64 32349 7e5d ./drivers/gpu/drm/bridge/tc358768.o
After:
text data bss dec hex filename
24749 7408 64 32221 7ddd ./drivers/gpu/drm/bridge/tc358768.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Rob Clark [Wed, 28 Jul 2021 01:06:12 +0000 (18:06 -0700)]
drm/msm: Track "seqno" fences by idr
Previously the (non-fd) fence returned from submit ioctl was a raw
seqno, which is scoped to the ring. But from UABI standpoint, the
ioctls related to seqno fences all specify a submitqueue. We can
take advantage of that to replace the seqno fences with a cyclic idr
handle.
This is in preperation for moving to drm scheduler, at which point
the submit ioctl will return after queuing the submit job to the
scheduler, but before the submit is written into the ring (and
therefore before a ring seqno has been assigned). Which means we
need to replace the dma_fence that userspace may need to wait on
with a scheduler fence.
Rob Clark [Wed, 28 Jul 2021 01:06:11 +0000 (18:06 -0700)]
drm/msm: Consolidate submit bo state
Move all the locked/active/pinned state handling to msm_gem_submit.c.
In particular, for drm/scheduler, we'll need to do all this before
pushing the submit job to the scheduler. But while we're at it we can
get rid of the dupicate pin and refcnt.
Rob Clark [Wed, 28 Jul 2021 01:06:09 +0000 (18:06 -0700)]
drm: Drop drm_gem_object_put_locked()
Now that no one is using it, remove it.
Signed-off-by: Rob Clark <robdclark@chromium.org> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://lore.kernel.org/r/20210728010632.2633470-5-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org>
Rob Clark [Mon, 26 Jul 2021 14:46:50 +0000 (07:46 -0700)]
drm/msm: Devfreq tuning
This adds a few things to try and make frequency scaling better match
the workload:
1) Longer polling interval to avoid whip-lashing between too-high and
too-low frequencies in certain workloads, like mobile games which
throttle themselves to 30fps.
Previously our polling interval was short enough to let things
ramp down to minimum freq in the "off" frame, but long enough to
not react quickly enough when rendering started on the next frame,
leading to uneven frame times. (Ie. rather than a consistent 33ms
it would alternate between 16/33/48ms.)
2) Awareness of when the GPU is active vs idle. Since we know when
the GPU is active vs idle, we can clamp the frequency down to the
minimum while it is idle. (If it is idle for long enough, then
the autosuspend delay will eventually kick in and power down the
GPU.)
Since devfreq has no knowledge of powered-but-idle, this takes a
small bit of trickery to maintain a "fake" frequency while idle.
This, combined with the longer polling period allows devfreq to
arrive at a reasonable "active" frequency, while still clamping
to minimum freq when idle to reduce power draw.
3) Boost. Because simple_ondemand needs to see a certain threshold
of busyness to ramp up, we could end up needing multiple polling
cycles before it reacts appropriately on interactive workloads
(ex. scrolling a web page after reading for some time), on top
of the already lengthened polling interval, when we see a idle
to active transition after a period of idle time we boost the
frequency that we return to.
Rob Clark [Mon, 26 Jul 2021 14:43:58 +0000 (07:43 -0700)]
drm/msm: Signal fences sooner
Nothing we do to in update_fences() can't be done in an atomic context,
so move this into the GPU's irq context to reduce latency (and call
dma_fence_signal() so we aren't relying on dma_fence_is_signaled() which
would defeat the purpose).
Rob Clark [Mon, 26 Jul 2021 14:43:57 +0000 (07:43 -0700)]
drm/msm: Let fences read directly from memptrs
Let dma_fence::signaled, etc, read directly from the address that the hw
is writing with updated completed fence seqno, so we can potentially
notice that the fence is signaled sooner.
drm/dp_mst: Fix return code on sideband message failure
Commit 2f015ec6eab6 ("drm/dp_mst: Add sideband down request tracing +
selftests") added some debug code for sideband message tracing. But
it seems to have unintentionally changed the behavior on sideband message
failure. It catches and returns failure only if DRM_UT_DP is enabled.
Otherwise it ignores the error code and returns success. So on an MST
unplug, the caller is unaware that the clear payload message failed and
ends up waiting for 4 seconds for the response. Fixes the issue by
returning the proper error code.
Changes in V2:
-- Revise commit text as review comment
-- add Fixes text
Changes in V3:
-- remove "unlikely" optimization
Fixes: 2f015ec6eab6 ("drm/dp_mst: Add sideband down request tracing + selftests") Cc: <stable@vger.kernel.org> # v5.5+ Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org> Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Jani Nikula <jani.nikula@intel.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/1625585434-9562-1-git-send-email-khsieh@codeaurora.org
Marek Vasut [Sun, 20 Jun 2021 22:49:46 +0000 (00:49 +0200)]
drm: mxsfb: Clear FIFO_CLEAR bit
Make sure the FIFO_CLEAR bit is latched in when configuring the
controller, so that the FIFO is really cleared. And then clear
the FIFO_CLEAR bit, since it is not self-clearing.
Fixes: 45d59d704080 ("drm: Add new driver for MXSFB controller") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Abrecht <public@danielabrecht.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Stefan Agner <stefan@agner.ch> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # i.Core MX8MM Acked-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210620224946.189524-1-marex@denx.de
Marek Vasut [Mon, 26 Jul 2021 19:44:57 +0000 (21:44 +0200)]
drm: mxsfb: Use bus_format from the nearest bridge if present
In case there is a bridge connected to the LCDIF, use bus_format
from the bridge, otherwise behave as before and use bus_format
from the connector. This way, even if there are multiple bridges
in the display pipeline, the LCDIF will use the correct format.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Abrecht <public@danielabrecht.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Stefan Agner <stefan@agner.ch> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210726194457.341696-1-marex@denx.de
Marek Vasut [Sun, 20 Jun 2021 22:47:59 +0000 (00:47 +0200)]
drm: mxsfb: Increase number of outstanding requests on V4 and newer HW
In case the DRAM is under high load, the MXSFB FIFO might underflow
and that causes visible artifacts. This could be triggered on i.MX8MM
using e.g. "$ memtester 128M" on a device with 1920x1080 panel. The
first "Stuck Address" test of the memtester will completely corrupt
the image on the panel and leave the MXSFB FIFO in odd state.
To avoid this underflow, increase number of outstanding requests to
DRAM from 2 to 16, which is the maximum. This mitigates the issue
and it can no longer be triggered.
Fixes: 45d59d704080 ("drm: Add new driver for MXSFB controller") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Abrecht <public@danielabrecht.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Stefan Agner <stefan@agner.ch> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210620224759.189351-1-marex@denx.de
Marek Vasut [Sun, 20 Jun 2021 22:47:01 +0000 (00:47 +0200)]
drm: mxsfb: Enable recovery on underflow
There is some sort of corner case behavior of the controller,
which could rarely be triggered at least on i.MX6SX connected
to 800x480 DPI panel and i.MX8MM connected to DPI->DSI->LVDS
bridged 1920x1080 panel (and likely on other setups too), where
the image on the panel shifts to the right and wraps around.
This happens either when the controller is enabled on boot or
even later during run time. The condition does not correct
itself automatically, i.e. the display image remains shifted.
It seems this problem is known and is due to sporadic underflows
of the LCDIF FIFO. While the LCDIF IP does have underflow/overflow
IRQs, neither of the IRQs trigger and neither IRQ status bit is
asserted when this condition occurs.
All known revisions of the LCDIF IP have CTRL1 RECOVER_ON_UNDERFLOW
bit, which is described in the reference manual since i.MX23 as
"
Set this bit to enable the LCDIF block to recover in the next
field/frame if there was an underflow in the current field/frame.
"
Enable this bit to mitigate the sporadic underflows.
Fixes: 45d59d704080 ("drm: Add new driver for MXSFB controller") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Abrecht <public@danielabrecht.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Stefan Agner <stefan@agner.ch> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210620224701.189289-1-marex@denx.de
projects / kernel.git / log