Esben Haabendal [Thu, 23 May 2019 12:02:20 +0000 (14:02 +0200)]
net: ll_temac: Prepare indirect register access for multicast support
With .ndo_set_rx_mode/temac_set_multicast_list() being called in atomic
context (holding addr_list_lock), and temac_set_multicast_list() needing
to access temac indirect registers, the mutex used to synchronize indirect
register is a no-no.
Replace it with a spinlock, and avoid sleeping in
temac_indirect_busywait().
To avoid excessive holding of the lock, which is now a spinlock, the
temac_device_reset() function is changed to only hold the lock for short
periods. With timeouts, it could be holding the spinlock for more than
2 seconds.
Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Esben Haabendal [Thu, 23 May 2019 12:02:19 +0000 (14:02 +0200)]
net: ll_temac: Do not make promiscuous mode sticky on multicast
When user has requested IFF_ALLMULTI or have set more than 4 multicast
addresses, we should just use promiscuous mode, but not set it in flags,
as it causes the interface to stay in promiscuous mode even when the
non-IFF_PROMISC condition that caused promiscuous mode to be enabled
has gone away.
Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe Leroy [Thu, 23 May 2019 08:55:32 +0000 (08:55 +0000)]
net: phy: lxt: Add suspend/resume support to LXT971 and LXT973.
All LXT PHYs implement the standard "power down" bit 11 of
BMCR, so this patch adds support using the generic
genphy_{suspend,resume} functions added by
commit 6370fe8e2204 ("phy: power management support").
LXT970 is left aside because all registers get cleared upon
"power down" exit.
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Muthuswamy [Wed, 22 May 2019 23:10:44 +0000 (23:10 +0000)]
hv_sock: perf: loop in send() to maximize bandwidth
Currently, the hv_sock send() iterates once over the buffer, puts data into
the VMBUS channel and returns. It doesn't maximize on the case when there
is a simultaneous reader draining data from the channel. In such a case,
the send() can maximize the bandwidth (and consequently minimize the cpu
cycles) by iterating until the channel is found to be full.
Perf data:
Total Data Transfer: 10GB/iteration
Single threaded reader/writer, Linux hvsocket writer with Windows hvsocket
reader
Packet size: 64KB
CPU sys time was captured using the 'time' command for the writer to send
10GB of data.
'Send Buffer Loop' is with the patch applied.
The values below are over 10 iterations.
|--------------------------------------------------------|
| | Current | Send Buffer Loop |
|--------------------------------------------------------|
| | Throughput | CPU sys | Throughput | CPU sys |
| | (MB/s) | time (s) | (MB/s) | time (s) |
|--------------------------------------------------------|
| Min | 407 | 7.048 | 401 | 5.958 |
|--------------------------------------------------------|
| Max | 455 | 7.563 | 542 | 6.993 |
|--------------------------------------------------------|
| Avg | 440 | 7.411 | 451 | 6.639 |
|--------------------------------------------------------|
| Median | 446 | 7.417 | 447 | 6.761 |
|--------------------------------------------------------|
Observation:
1. The avg throughput doesn't really change much with this change for this
scenario. This is most probably because the bottleneck on throughput is
somewhere else.
2. The average system (or kernel) cpu time goes down by 10%+ with this
change, for the same amount of data transfer.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Muthuswamy [Wed, 22 May 2019 22:56:07 +0000 (22:56 +0000)]
hv_sock: perf: Allow the socket buffer size options to influence the actual socket buffers
Currently, the hv_sock buffer size is static and can't scale to the
bandwidth requirements of the application. This change allows the
applications to influence the socket buffer sizes using the SO_SNDBUF and
the SO_RCVBUF socket options.
Few interesting points to note:
1. Since the VMBUS does not allow a resize operation of the ring size, the
socket buffer size option should be set prior to establishing the
connection for it to take effect.
2. Setting the socket option comes with the cost of that much memory being
reserved/allocated by the kernel, for the lifetime of the connection.
Perf data:
Total Data Transfer: 1GB
Single threaded reader/writer
Results below are summarized over 10 iterations.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 22 May 2019 19:11:06 +0000 (12:11 -0700)]
selftests: pmtu: Simplify cleanup and namespace names
The point of the pause-on-fail argument is to leave the setup as is after
a test fails to allow a user to debug why it failed. Move the cleanup
after posting the result to the user to make it so.
Random names for the namespaces are not user friendly when trying to
debug a failure. Make them simpler and more direct for the tests. Run
cleanup at the beginning to ensure they are cleaned up if they already
exist.
Remove cleanup_done. There is no harm in doing cleanup twice; just
ignore any errors related to not existing - which is already done.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 22 May 2019 19:09:16 +0000 (12:09 -0700)]
selftests: fib-onlink: Make quiet by default
Add VERBOSE argument to fib-onlink-tests.sh and make output quiet by
default. Add getopt parsing of inputs and support for -v (verbose) and
-p (pause on fail).
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 22 May 2019 19:07:43 +0000 (12:07 -0700)]
net: Set strict_start_type for routes and rules
New userspace on an older kernel can send unknown and unsupported
attributes resulting in an incompelete config which is almost
always wrong for routing (few exceptions are passthrough settings
like the protocol that installed the route).
Set strict_start_type in the policies for IPv4 and IPv6 routes and
rules to detect new, unsupported attributes and fail the route add.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: Export functions for nexthop code
This set exports ipv4 and ipv6 fib functions for use by the nexthop
code. It also adds new ones to send route notifications if a nexthop
configuration changes.
v2
- repost of patches dropped at the end of the last dev window
added patch 8 which exports nh_update_mtu since it is inline with
the other patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 22 May 2019 19:04:42 +0000 (12:04 -0700)]
ipv4: Add function to send route updates
Add fib_info_notify_update to walk the fib and send RTM_NEWROUTE
notifications with NLM_F_REPLACE set for entries linked to a fib_info
that have nh_updated flag set. This helper will be used by the nexthop
code to notify userspace of routes that are impacted when a nexthop
config is updated via replace. The new function and its helper are
similar to how fib_flush and fib_table_flush work for address delete
and link down events.
This notification is needed for legacy apps that do not understand
the new nexthop object. Apps that are nexthop aware can use the
RTA_NH_ID attribute in the route notification to just ignore it.
In the future this should be wrapped in a sysctl to allow OS'es that
are fully updated to avoid the notificaton storm.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 22 May 2019 19:04:41 +0000 (12:04 -0700)]
ipv6: export function to send route updates
Add fib6_rt_update to send RTM_NEWROUTE with NLM_F_REPLACE set. This
helper will be used by the nexthop code to notify userspace of routes
that are impacted when a nexthop config is updated via replace.
This notification is needed for legacy apps that do not understand
the new nexthop object. Apps that are nexthop aware can use the
RTA_NH_ID attribute in the route notification to just ignore it.
In the future this should be wrapped in a sysctl to allow OS'es that
are fully updated to avoid the notificaton storm.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 May 2019 00:46:28 +0000 (17:46 -0700)]
Merge branch 'net-phy-T1-support'
Andrew Lunn says:
====================
net: phy: T1 support
T1 PHYs make use of a single twisted pair, rather than the traditional
2 pair for 100BaseT or 4 pair for 1000BaseT. This patchset adds link
modes for 100BaseT1 and 1000BaseT1, and them makes use of 100BaseT1 in
the list of PHY features used by current T1 drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trent Piepho [Wed, 22 May 2019 18:43:27 +0000 (18:43 +0000)]
net: phy: dp83867: Allocate state struct in probe
This was being done in config the first time the phy was configured.
Should be in the probe method.
Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Trent Piepho [Wed, 22 May 2019 18:43:26 +0000 (18:43 +0000)]
net: phy: dp83867: Validate FIFO depth property
Insure property is in valid range and fail when reading DT if it is not.
Also add error message for existing failure if required property is not
present.
Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Trent Piepho [Wed, 22 May 2019 18:43:25 +0000 (18:43 +0000)]
net: phy: dp83867: IO impedance is not dependent on RGMII delay
The driver would only set the IO impedance value when RGMII internal
delays were enabled. There is no reason for this. Move the IO
impedance block out of the RGMII delay block.
Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Trent Piepho [Wed, 22 May 2019 18:43:24 +0000 (18:43 +0000)]
net: phy: dp83867: Use unsigned variables to store unsigned properties
The variables used to store u32 DT properties were signed ints. This
doesn't work properly if the value of the property were to overflow.
Use unsigned variables so this doesn't happen.
Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The code was assuming the reset default of the delay control register
was to have delay disabled. This is what the datasheet shows as the
register's initial value. However, that's not actually true: the
default is controlled by the PHY's pin strapping.
If the interface mode is selected as RX or TX delay only, insure the
other direction's delay is disabled.
If the interface mode is just "rgmii", with neither TX or RX internal
delay, one might expect that the driver should disable both delays. But
this is not what the driver does. It leaves the setting at the PHY's
strapping's default. And that default, for no pins with strapping
resistors, is to have delay enabled and 2.00 ns.
Rather than change this behavior, I've kept it the same and documented
it. No delay will most likely not work and will break ethernet on any
board using "rgmii" mode. If the board is strapped to have a delay and
is configured to use "rgmii" mode a warning is generated that "rgmii-id"
should have been used.
Also validate the delay values and fail if they are not in range.
Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Trent Piepho [Wed, 22 May 2019 18:43:22 +0000 (18:43 +0000)]
net: phy: dp83867: Add ability to disable output clock
Generally, the output clock pin is only used for testing and only serves
as a source of RF noise after this. It could be used to daisy-chain
PHYs, but this is uncommon. Since the PHY can disable the output, make
doing so an option. I do this by adding another enumeration to the
allowed values of ti,clk-output-sel.
The code was not using the value DP83867_CLK_O_SEL_REF_CLK as one might
expect: to select the REF_CLK as the output. Rather it meant "keep
clock output setting as is", which, depending on PHY strapping, might
not be outputting REF_CLK.
Change this so DP83867_CLK_O_SEL_REF_CLK means enable REF_CLK output.
Omitting the property will leave the setting as is (which was the
previous behavior in this case).
Out of range values were silently converted into
DP83867_CLK_O_SEL_REF_CLK. Change this so they generate an error.
Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Trent Piepho [Wed, 22 May 2019 18:43:21 +0000 (18:43 +0000)]
dt-bindings: phy: dp83867: Add documentation for disabling clock output
The clock output is generally only used for testing and development and
not used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Trent Piepho [Wed, 22 May 2019 18:43:19 +0000 (18:43 +0000)]
dt-bindings: phy: dp83867: Describe how driver behaves w.r.t rgmii delay
Add a note to make it more clear how the driver behaves when "rgmii" vs
"rgmii-id", "rgmii-idrx", or "rgmii-idtx" interface modes are selected.
Cc: Rob Herring <robh+dt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Vishal Kulkarni [Wed, 22 May 2019 16:16:12 +0000 (21:46 +0530)]
cxgb4: Enable hash filter with offload
Hash (exact-match) filters used for offloading flows share the
same active region resources on the chip with upper layer drivers,
like iw_cxgb4, chcr, etc. Currently, only either Hash filters
or ULDs can use the active region resources, but not both. Hence,
use the new firmware configuration parameters (when available)
to allow both the Hash filters and ULDs to share the
active region simultaneously.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felipe Gasper [Tue, 21 May 2019 00:43:51 +0000 (19:43 -0500)]
net: Add UNIX_DIAG_UID to Netlink UNIX socket diagnostics.
This adds the ability for Netlink to report a socket's UID along with the
other UNIX diagnostic information that is already available. This will
allow diagnostic tools greater insight into which users control which
socket.
To test this, do the following as a non-root user:
unshare -U -r bash
nc -l -U user.socket.$$ &
.. and verify from within that same session that Netlink UNIX socket
diagnostics report the socket's UID as 0. Also verify that Netlink UNIX
socket diagnostics report the socket's UID as the user's UID from an
unprivileged process in a different session. Verify the same from
a root process.
Signed-off-by: Felipe Gasper <felipe@felipegasper.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 22 May 2019 15:36:16 +0000 (08:36 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
- Fix SPE probe failure when backing auxbuf with high-order pages
- Fix handling of DMA allocations from outside of the vmalloc area
- Fix generation of build-id ELF section for vDSO object
- Disable huge I/O mappings if kernel page table dumping is enabled
- A few other minor fixes (comments, kconfig etc)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: vdso: Explicitly add build-id option
arm64/mm: Inhibit huge-vmap with ptdump
arm64: Print physical address of page table base in show_pte()
arm64: don't trash config with compat symbol if COMPAT is disabled
arm64: assembler: Update comment above cond_yield_neon() macro
drivers/perf: arm_spe: Don't error on high-order pages for aux buf
arm64/iommu: handle non-remapped addresses in ->mmap and ->get_sgtable
1) Clear up some recent tipc regressions because of registration
ordering. Fix from Junwei Hu.
2) tipc's TLV_SET() can read past the end of the supplied buffer during
the copy. From Chris Packham.
3) ptp example program doesn't match the kernel, from Richard Cochran.
4) Outgoing message type fix in qrtr, from Bjorn Andersson.
5) Flow control regression in stmmac, from Tan Tee Min.
6) Fix inband autonegotiation in phylink, from Russell King.
7) Fix sk_bound_dev_if handling in rawv6_bind(), from Mike Manning.
8) Fix usbnet crash after disconnect, from Kloetzke Jan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
usbnet: fix kernel crash after disconnect
selftests: fib_rule_tests: use pre-defined DEV_ADDR
net-next: net: Fix typos in ip-sysctl.txt
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
net: phylink: ensure inband AN works correctly
usbnet: ipheth: fix racing condition
net: stmmac: dma channel control register need to be init first
net: stmmac: fix ethtool flow control not able to get/set
net: qrtr: Fix message type of outgoing packets
networking: : fix typos in code comments
ptp: Fix example program to match kernel.
fddi: fix typos in code comments
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
selftests: fib_rule_tests: fix local IPv4 address typo
tipc: Avoid copying bytes beyond the supplied data
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
vlan: Mark expected switch fall-through
macvlan: Mark expected switch fall-through
net/mlx4_en: ethtool, Remove unsupported SFP EEPROM high pages query
...
Linus Torvalds [Wed, 22 May 2019 15:10:35 +0000 (08:10 -0700)]
Merge tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a particularly glaring oversight in a DM core commit from 5.1 that
doesn't properly trim special IOs (e.g. discards) relative to
corresponding target's max_io_len_target_boundary()"
* tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: make sure to obey max_io_len_target_boundary
Commit 27908daf3d7e changed the types of the statistic values in struct
gfs2_lkstats from s64 to u64. Because of that, what should be a signed
value in gfs2_update_stats turned into an unsigned value. When shifted
right, we end up with a large positive value instead of a small negative
value, which results in an incorrect variance estimate.
Fixes: 27908daf3d7e ("gfs2: Make statistics unsigned, suitable for use with do_div()") Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Cc: stable@vger.kernel.org # v4.4+
Michael Lass [Tue, 21 May 2019 19:58:07 +0000 (21:58 +0200)]
dm: make sure to obey max_io_len_target_boundary
Commit a0b8e6c11bbb ("dm: eliminate 'split_discard_bios' flag from DM
target interface") incorrectly removed code from
__send_changing_extent_only() that is required to impose a per-target IO
boundary on IO that exceeds max_io_len_target_boundary(). Otherwise
"special" IO (e.g. DISCARD, WRITE SAME, WRITE ZEROES) can write beyond
where allowed.
Fix this by restoring the max_io_len_target_boundary() limit in
__send_changing_extent_only()
Fixes: a0b8e6c11bbb ("dm: eliminate 'split_discard_bios' flag from DM target interface") Cc: stable@vger.kernel.org # 5.1+ Signed-off-by: Michael Lass <bevan@bi-co.net> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The crash happens roughly 125..130ms after the disconnect. This
correlates with the 'delay' timer that is started on certain USB tx/rx
errors in the URB completion handler.
The problem is a race of usbnet_stop() with usbnet_start_xmit(). In
usbnet_stop() we call usbnet_terminate_urbs() to cancel all URBs in
flight. This only makes sense if no new URBs are submitted
concurrently, though. But the usbnet_start_xmit() can run at the same
time on another CPU which almost unconditionally submits an URB. The
error callback of the new URB will then schedule the timer after it was
already stopped.
The fix adds a check if the tx queue is stopped after the tx list lock
has been taken. This should reliably prevent the submission of new URBs
while usbnet_terminate_urbs() does its job. The same thing is done on
the rx side even though it might be safe due to other flags that are
checked there.
Signed-off-by: Jan Klötzke <Jan.Kloetzke@preh.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Tue, 21 May 2019 06:40:47 +0000 (14:40 +0800)]
selftests: fib_rule_tests: use pre-defined DEV_ADDR
DEV_ADDR is defined but not used. Use it in address setting.
Do the same with IPv6 for consistency.
Reported-by: David Ahern <dsahern@gmail.com> Fixes: 5ee583f884fe ("selftests: fib_rule_tests: fix local IPv4 address typo") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Manning [Mon, 20 May 2019 18:57:17 +0000 (19:57 +0100)]
ipv6: Consider sk_bound_dev_if when binding a raw socket to an address
IPv6 does not consider if the socket is bound to a device when binding
to an address. The result is that a socket can be bound to eth0 and
then bound to the address of eth1. If the device is a VRF, the result
is that a socket can only be bound to an address in the default VRF.
Resolve by considering the device if sk_bound_dev_if is set.
Signed-off-by: Mike Manning <mmanning@vyatta.att-mail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bernd Eckstein [Mon, 20 May 2019 15:31:09 +0000 (17:31 +0200)]
usbnet: ipheth: fix racing condition
Fix a racing condition in ipheth.c that can lead to slow performance.
Bug: In ipheth_tx(), netif_wake_queue() may be called on the callback
ipheth_sndbulk_callback(), _before_ netif_stop_queue() is called.
When this happens, the queue is stopped longer than it needs to be,
thus reducing network performance.
Fix: Move netif_stop_queue() in front of usb_submit_urb(). Now the order
is always correct. In case, usb_submit_urb() fails, the queue is woken up
again as callback will not fire.
Testing: This racing condition is usually not noticeable, as it has to
occur very frequently to slowdown the network. The callback from the USB
is usually triggered slow enough, so the situation does not appear.
However, on a Ubuntu Linux on VMWare Workstation, running on Windows 10,
the we loose the race quite often and the following speedup can be noticed:
Without this patch: Download: 4.10 Mbit/s, Upload: 4.01 Mbit/s
With this patch: Download: 36.23 Mbit/s, Upload: 17.61 Mbit/s
Signed-off-by: Oliver Zweigle <Oliver.Zweigle@faro.com> Signed-off-by: Bernd Eckstein <3ernd.Eckstein@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 21 May 2019 19:33:38 +0000 (12:33 -0700)]
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Thomas Gleixner [Sun, 19 May 2019 13:51:55 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it would be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 6 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154043.007767574@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:54 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.917228456@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:53 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
Based on 1 normalized pattern(s):
this software may be redistributed and or modified under the terms
of the gnu general public license as published by the free software
foundation either version 2 of the license or any later version this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.800979546@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:52 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.707528683@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:51 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.615184352@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:50 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program see the file copying if not write to the free
software foundation inc 51 franklin steet fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 41 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.524645346@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:49 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation 51
franklin street fifth floor boston ma 02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.432790911@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:48 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program see
the file copying if not write to the free software foundation 675
mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 52 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.342335923@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:47 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 13 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.236620792@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:45 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses the full gnu
general public license is included in this distribution in the file
called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154042.045106120@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:44 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
Based on 1 normalized pattern(s):
gnu cc is free software you can redistribute it and or modify it
under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version gnu cc is distributed in the hope that it will be
useful but without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details you should have received a
copy of the gnu general public license along with gnu cc see the
file copying if not write to the free software foundation 59 temple
place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154041.940713800@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:43 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:42 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose good title or non infringement see the gnu general public
license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 7 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154041.727898173@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:41 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
Based on 1 normalized pattern(s):
this program is free software you can distribute it and or modify it
under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154041.622608495@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:39 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not you can access it online at http www gnu
org licenses gpl 2 0 html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154041.430943677@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:37 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details the full
gnu general public license is included in this distribution in the
file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154041.244154651@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:35 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses the full gnu
general public license is included in this distribution in the file
called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154041.052102771@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:33 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 or
later as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154040.848507137@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Sun, 19 May 2019 13:51:31 +0000 (15:51 +0200)]
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 1
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Abeni [Fri, 10 May 2019 17:12:33 +0000 (19:12 +0200)]
selinux: do not report error on connect(AF_UNSPEC)
calling connect(AF_UNSPEC) on an already connected TCP socket is an
established way to disconnect() such socket. After commit f36441ecf59f
("selinux: Fix ltp test connect-syscall failure") it no longer works
and, in the above scenario connect() fails with EAFNOSUPPORT.
Fix the above explicitly early checking for AF_UNSPEC family, and
returning success in that case.
Reported-by: Tom Deseyn <tdeseyn@redhat.com> Cc: stable@vger.kernel.org Fixes: f36441ecf59f ("selinux: Fix ltp test connect-syscall failure") Suggested-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com>
Weifeng Voon [Tue, 21 May 2019 05:38:38 +0000 (13:38 +0800)]
net: stmmac: dma channel control register need to be init first
stmmac_init_chan() needs to be called before stmmac_init_rx_chan() and
stmmac_init_tx_chan(). This is because if PBLx8 is to be used,
"DMA_CH(#i)_Control.PBLx8" needs to be set before programming
"DMA_CH(#i)_TX_Control.TxPBL" and "DMA_CH(#i)_RX_Control.RxPBL".
Fixes: 2152659d431b ("net: stmmac: dma channel init prepared for multiple queues") Reviewed-by: Zhang, Baoli <baoli.zhang@intel.com> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Weifeng Voon <weifeng.voon@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tan, Tee Min [Tue, 21 May 2019 04:55:42 +0000 (12:55 +0800)]
net: stmmac: fix ethtool flow control not able to get/set
Currently ethtool was not able to get/set the flow control due to a
missing "!". It will always return -EOPNOTSUPP even the device is
flow control supported.
This patch fixes the condition check for ethtool flow control get/set
function for ETHTOOL_LINK_MODE_Asym_Pause_BIT.
Fixes: b3e9409876df (“net: ethernet: Convert phydev advertize and supported from u32 to link mode”) Signed-off-by: Tan, Tee Min <tee.min.tan@intel.com> Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Voon, Weifeng <weifeng.voon@intel.com@intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjorn Andersson [Mon, 20 May 2019 23:51:56 +0000 (16:51 -0700)]
net: qrtr: Fix message type of outgoing packets
QRTR packets has a message type in the header, which is repeated in the
control header. For control packets we therefor copy the type from
beginning of the outgoing payload and use that as message type.
For non-control messages an endianness fix introduced in v5.2-rc1 caused the
type to be 0, rather than QRTR_TYPE_DATA, causing all messages to be dropped by
the receiver. Fix this by converting and using qrtr_type, which will remain
QRTR_TYPE_DATA for non-control messages.
Fixes: 9173c8b7d708 ("net: qrtr: use protocol endiannes variable") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Richard Cochran [Mon, 20 May 2019 05:15:05 +0000 (22:15 -0700)]
ptp: Fix example program to match kernel.
Ever since commit 1f8f4c3d15b3 ("posix-clocks: Remove interval timer
facility and mmap/fasync callbacks") the possibility of PHC based
posix timers has been removed. In addition it will probably never
make sense to implement this functionality.
This patch removes the misleading example code which seems to suggest
that posix timers for PHC devices will ever be a thing.
Signed-off-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 21 May 2019 00:22:17 +0000 (17:22 -0700)]
Merge tag 'kbuild-fixes-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- remove unused cc-ldoption
- do not check the name uniquness of builtin modules to avoid false
positives
* tag 'kbuild-fixes-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: do not check name uniqueness of builtin modules
kbuild: drop support for cc-ldoption
David S. Miller [Tue, 21 May 2019 00:20:20 +0000 (20:20 -0400)]
Merge branch 'kselftests-fib_rule_tests-fix'
Hangbin Liu says:
====================
kselftests: fib_rule_tests: fix "from $SRC_IP iif $DEV" match testing
As all the IPv4 testing addresses are in the same subnet and egress device ==
ingress device, to pass "from $SRC_IP iif $DEV" match test, we need enable
forwarding to get the route entry.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Mon, 20 May 2019 04:36:55 +0000 (12:36 +0800)]
selftests: fib_rule_tests: enable forwarding before ipv4 from/iif test
As all the testing addresses are in the same subnet and egress device ==
ingress device. We need enable forwarding to get the route entry.
Also disable rp_filer separately as some distributions enable it in
startup scripts.
Fixes: 78c7db66253e ("selftests: net: initial fib rule tests") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Mon, 20 May 2019 04:36:54 +0000 (12:36 +0800)]
selftests: fib_rule_tests: fix local IPv4 address typo
The IPv4 testing address are all in 192.51.100.0 subnet. It doesn't make
sense to set a 198.51.100.1 local address. Should be a typo.
Fixes: 78c7db66253e ("selftests: net: initial fib rule tests") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Packham [Mon, 20 May 2019 03:45:36 +0000 (15:45 +1200)]
tipc: Avoid copying bytes beyond the supplied data
TLV_SET is called with a data pointer and a len parameter that tells us
how many bytes are pointed to by data. When invoking memcpy() we need
to careful to only copy len bytes.
Previously we would copy TLV_LENGTH(len) bytes which would copy an extra
4 bytes past the end of the data pointer which newer GCC versions
complain about.
In file included from test.c:17:
In function 'TLV_SET',
inlined from 'test' at test.c:186:5:
/usr/include/linux/tipc_config.h:317:3:
warning: 'memcpy' forming offset [33, 36] is out of the bounds [0, 32]
of object 'bearer_name' with type 'char[32]' [-Warray-bounds]
memcpy(TLV_DATA(tlv_ptr), data, tlv_len);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
test.c: In function 'test':
test.c::161:10: note:
'bearer_name' declared here
char bearer_name[TIPC_MAX_BEARER_NAME];
^~~~~~~~~~~
We still want to ensure any padding bytes at the end are initialised, do
this with a explicit memset() rather than copy bytes past the end of
data. Apply the same logic to TCM_SET.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 21 May 2019 00:00:47 +0000 (20:00 -0400)]
Merge branch 'net-readx_poll_timeout'
Benedikt Spranger says:
====================
Convert mdio wait function to use readx_poll_timeout()
On loaded systems with a preemptible kernel both functions
axienet_mdio_wait_until_ready() and xemaclite_mdio_wait() may report a
false positive error return.
Convert both functions to use readx_poll_timeout() to handle the
situation in a safe manner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kurt Kanzenbach [Sun, 19 May 2019 17:59:37 +0000 (19:59 +0200)]
2/2] net: xilinx_emaclite: use readx_poll_timeout() in mdio wait function
On loaded systems with a preemptible kernel the mdio_wait() function may
report an error while everything is working fine:
xemaclite_mdio_wait():
xemaclite_readl() -> chip not ready
--> interrupt here (other work for some time / chip become ready)
if (time_before_eq(end, jiffies))
--> false positive error report
Replace the current code with readx_poll_timeout() which takes care
of the situation.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Kurt Kanzenbach [Sun, 19 May 2019 17:59:36 +0000 (19:59 +0200)]
1/2] net: axienet: use readx_poll_timeout() in mdio wait function
On loaded systems with a preemptible kernel the mdio_wait() function may
report an error while everything is working fine:
axienet_mdio_wait_until_ready():
axienet_ior() -> chip not ready
--> interrupt here (other work for some time / chip become ready)
if (time_before_eq(end, jiffies))
--> false positive error report
Replace the current code with readx_poll_timeout() which take care
of the situation.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Masahiro Yamada [Mon, 20 May 2019 02:54:37 +0000 (11:54 +0900)]
kbuild: do not check name uniqueness of builtin modules
I just thought it was a good idea to scan builtin.modules in the name
uniqueness checking, but a couple of false positives were found.
Stephen reported a false positive for ppc64_defconfig:
warning: same basename if the following are built as modules:
arch/powerpc/platforms/powermac/nvram.ko
drivers/char/nvram.ko
The former is never built as a module as you see in
arch/powerpc/platforms/powermac/Makefile:
# CONFIG_NVRAM is an arch. independent tristate symbol, for pmac32 we really
# need this to be a bool. Cheat here and pretend CONFIG_NVRAM=m is really
# CONFIG_NVRAM=y
obj-$(CONFIG_NVRAM:m=y) += nvram.o
Another example of false positive is arm64 defconfig:
warning: same basename if the following are built as modules:
arch/arm64/lib/crc32.ko
lib/crc32.ko
It is true CONFIG_CRC32 is a tristate option but it is always 'y' since
it is select'ed by ARM64. Hence, neither of them is built as a module
for the arm64 build.
From the above, modules.builtin essentially contains false positives.
I do not think it is a big deal as far as kmod is concerned, but false
positive warnings in the kernel build make people upset. It is better
to not check it.
Even without builtin.modules checked, we have enough (and more solid)
test coverage with allmodconfig.
While I touched this part, I replaced the sed code with neater one
provided by Stephen.
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
net/8021q/vlan_dev.c: In function ‘vlan_dev_ioctl’:
net/8021q/vlan_dev.c:374:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!net_eq(dev_net(dev), &init_net))
^
net/8021q/vlan_dev.c:376:2: note: here
case SIOCGMIIPHY:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/macvlan.c: In function ‘macvlan_do_ioctl’:
drivers/net/macvlan.c:839:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (!net_eq(dev_net(dev), &init_net))
^
drivers/net/macvlan.c:841:2: note: here
case SIOCGHWTSTAMP:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Junwei Hu [Mon, 20 May 2019 06:43:59 +0000 (14:43 +0800)]
tipc: fix modprobe tipc failed after switch order of device registration
Error message printed:
modprobe: ERROR: could not insert 'tipc': Address family not
supported by protocol.
when modprobe tipc after the following patch: switch order of
device registration, commit 6f91e0addec4
("tipc: switch order of device registration to fix a crash")
Because sock_create_kern(net, AF_TIPC, ...) called by
tipc_topsrv_create_listener() in the initialization process
of tipc_init_net(), so tipc_socket_init() must be execute before that.
Meanwhile, tipc_net_id need to be initialized when sock_create()
called, and tipc_socket_init() is no need to be called for each namespace.
I add a variable tipc_topsrv_net_ops, and split the
register_pernet_subsys() of tipc into two parts, and split
tipc_socket_init() with initialization of pernet params.
By the way, I fixed resources rollback error when tipc_bcast_init()
failed in tipc_init_net().
Fixes: 6f91e0addec4 ("tipc: switch order of device registration to fix a crash") Signed-off-by: Junwei Hu <hujunwei4@huawei.com> Reported-by: Wang Wang <wangwang2@huawei.com> Reported-by: syzbot+1e8114b61079bfe9cbc5@syzkaller.appspotmail.com Reviewed-by: Kang Zhou <zhoukang7@huawei.com> Reviewed-by: Suanming Mou <mousuanming@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 20 May 2019 16:52:35 +0000 (09:52 -0700)]
Merge tag 'for-5.2-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Notable highlights:
- fixes for some long-standing bugs in fsync that were quite hard to
catch but now finaly fixed
- some fixups to error handling paths that did not properly clean up
(locking, memory)
- fix to space reservation for inheriting properties"
* tag 'for-5.2-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: tree-checker: detect file extent items with overlapping ranges
Btrfs: fix race between ranged fsync and writeback of adjacent ranges
Btrfs: avoid fallback to transaction commit during fsync of files with holes
btrfs: extent-tree: Fix a bug that btrfs is unable to add pinned bytes
btrfs: sysfs: don't leak memory when failing add fsid
btrfs: sysfs: Fix error path kobject memory leak
Btrfs: do not abort transaction at btrfs_update_root() after failure to COW path
btrfs: use the existing reserved items for our first prop for inheritance
btrfs: don't double unlock on error in btrfs_punch_hole
btrfs: Check the compression level before getting a workspace
10) The netdev_xmit_more() conversion was not done %100 properly in mlx5
driver, fix from Tariq Toukan.
11) Clean up botched merge on netfilter kselftest, from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (74 commits)
of_net: fix of_get_mac_address retval if compiled without CONFIG_OF
net: fix kernel-doc warnings for socket.c
net: Treat sock->sk_drops as an unsigned int when printing
kselftests: netfilter: fix leftover net/net-next merge conflict
mlxsw: core: Prevent reading unsupported slave address from SFP EEPROM
mlxsw: core: Prevent QSFP module initialization for old hardware
vsock/virtio: Initialize core virtio vsock before registering the driver
net/mlx5e: Fix possible modify header actions memory leak
net/mlx5e: Fix no rewrite fields with the same match
net/mlx5e: Additional check for flow destination comparison
net/mlx5e: Add missing ethtool driver info for representors
net/mlx5e: Fix number of vports for ingress ACL configuration
net/mlx5e: Fix ethtool rxfh commands when CONFIG_MLX5_EN_RXNFC is disabled
net/mlx5e: Fix wrong xmit_more application
net/mlx5: Fix peer pf disable hca command
net/mlx5: E-Switch, Correct type to u16 for vport_num and int for vport_index
net/mlx5: Add meaningful return codes to status_to_err function
net/mlx5: Imply MLXFW in mlx5_core
Revert "tipc: fix modprobe tipc failed after switch order of device registration"
vsock/virtio: free packets during the socket release
...
Nick Desaulniers [Tue, 23 Apr 2019 21:27:41 +0000 (14:27 -0700)]
kbuild: drop support for cc-ldoption
If you want to see if your linker supports a certain flag, then ask the
linker directly with ld-option (not the compiler with cc-ldoption).
Checking for linker flag support is an antipattern that complicates the
usage of various linkers other than bfd via -fuse-ld={bfd|gold|lld}.
Linus Torvalds [Sun, 19 May 2019 22:22:03 +0000 (15:22 -0700)]
Merge tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBIFS fixes from Richard Weinberger:
- build errors wrt xattrs
- mismerge which lead to a wrong Kconfig ifdef
- missing endianness conversion
* tag 'upstream-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: Convert xattr inum to host order
ubifs: Use correct config name for encryption
ubifs: Fix build error without CONFIG_UBIFS_FS_XATTR
Linus Torvalds [Sun, 19 May 2019 19:15:32 +0000 (12:15 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge yet more updates from Andrew Morton:
"A few final bits:
- large changes to vmalloc, yielding large performance benefits
- tweak the console-flush-on-panic code
- a few fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
panic: add an option to replay all the printk message in buffer
initramfs: don't free a non-existent initrd
fs/writeback.c: use rcu_barrier() to wait for inflight wb switches going into workqueue when umount
mm/compaction.c: correct zone boundary handling when isolating pages from a pageblock
mm/vmap: add DEBUG_AUGMENT_LOWEST_MATCH_CHECK macro
mm/vmap: add DEBUG_AUGMENT_PROPAGATE_CHECK macro
mm/vmalloc.c: keep track of free blocks for vmap allocation
Linus Torvalds [Sun, 19 May 2019 18:53:58 +0000 (11:53 -0700)]
Merge tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- remove unneeded use of cc-option, cc-disable-warning, cc-ldoption
- exclude tracked files from .gitignore
- re-enable -Wint-in-bool-context warning
- refactor samples/Makefile
- stop building immediately if syncconfig fails
- do not sprinkle error messages when $(CC) does not exist
- move arch/alpha/defconfig to the configs subdirectory
- remove crappy header search path manipulation
- add comment lines to .config to clarify the end of menu blocks
- check uniqueness of module names (adding new warnings intentionally)
* tag 'kbuild-v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (24 commits)
kconfig: use 'else ifneq' for Makefile to improve readability
kbuild: check uniqueness of module names
kconfig: Terminate menu blocks with a comment in the generated config
kbuild: add LICENSES to KBUILD_ALLDIRS
kbuild: remove 'addtree' and 'flags' magic for header search paths
treewide: prefix header search paths with $(srctree)/
media: prefix header search paths with $(srctree)/
media: remove unneeded header search paths
alpha: move arch/alpha/defconfig to arch/alpha/configs/defconfig
kbuild: terminate Kconfig when $(CC) or $(LD) is missing
kbuild: turn auto.conf.cmd into a mandatory include file
.gitignore: exclude .get_maintainer.ignore and .gitattributes
kbuild: add all Clang-specific flags unconditionally
kbuild: Don't try to add '-fcatch-undefined-behavior' flag
kbuild: add some extra warning flags unconditionally
kbuild: add -Wvla flag unconditionally
arch: remove dangling asm-generic wrappers
samples: guard sub-directories with CONFIG options
kbuild: re-enable int-in-bool-context warning
MAINTAINERS: kbuild: Add pattern for scripts/*vmlinux*
...
projects / kernel.git / log