drm/todo: Add entry for using kunit in the subsystem
The Kernel Unit Testing (KUnit) framework provides a common framework for
unit tests within the Linux kernel. Having a test suite would allow to
identify regressions earlier.
drm/mgag200: Protect concurrent access to I/O registers with lock
Add a mutex lock to protect concurrent access to I/O registers
against each other. This happens between invocation of commit-
tail functions and get-mode operations. Both with use the CRTC
index registers MGA1064_GEN_IO_DATA and MGA1064_GEN_IO_CTL.
Concurrent access can lead to failed mode-setting operations.
v2:
* fix typo in commit description (Jocelyn)
* add comment to explain rmmio_lock
drm/ast: Protect concurrent access to I/O registers with lock
Add a mutex lock to protect concurrent access to I/O registers
against each other. This happens between invocation of commit-
tail functions and get-mode operations. Both with use the CRTC
index register AST_IO_CRTC_PORT. Concurrent access can lead to
failed mode-setting operations.
drm/format-helper: Share implementation among conversion helpers
Provide format-independent conversion helpers for system and I/O
memory. Implement most existing helpers on top of it. The source and
destination formats of each conversion is handled by a per-line
helper that is given to the generic implementation.
drm/format-helper: Remove optional byte-swap from line convertion
Implement per-pixel byte swapping in a separate conversion helper
for the single function that requires it. Select the correct helper
for each conversion.
drm/format-helper: Implement drm_fb_swab() with per-line helpers
Replace the inner loop of drm_fb_swab() with helper functions that
swap the bytes in each pixel. This will allow to share the outer
loop with other conversion helpers.
Marek Vasut [Fri, 29 Apr 2022 20:46:25 +0000 (22:46 +0200)]
drm/bridge: tc358767: Fix DP bridge mode detection from DT endpoints
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP
port is optional. In case this port is not described in DT, the bridge
driver operates in DPI-to-DP mode. Make sure the driver treats this as
a valid mode of operation instead of reporting invalid mode.
Fixes: d6341964b973 ("drm/bridge: tc358767: Detect bridge mode from connected endpoints in DT") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Marek Vasut <marex@denx.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220429204625.241591-1-marex@denx.de
Marek Vasut [Fri, 29 Apr 2022 21:23:13 +0000 (23:23 +0200)]
drm: mxsfb: Implement LCDIF scanout CRC32 support
The LCDIF controller as present in i.MX28/i.MX6SX/i.MX8M Mini/Nano has
CRC_STAT register, which contains CRC32 of the frame as it was clocked
out of the DPI interface of the LCDIF. This is most likely meant as a
functional safety feature.
Unfortunately, there is zero documentation on how the CRC32 is calculated,
there is no documentation of the polynomial, the init value, nor on which
data is the checksum applied.
By applying brute-force on 8 pixel / 2 line frame, which is the minimum
size LCDIF would work with, it turns out the polynomial is CRC32_POLY_LE
0xedb88320 , init value is 0xffffffff , the input data are bitrev32()
of the entire frame and the resulting CRC has to be also bitrev32()ed.
Doing this calculation in kernel for each frame is unrealistic due to the
CPU demand, so attach the CRC collected from hardware to a frame instead.
The DRM subsystem already has an interface for this purpose and the CRC
can be accessed e.g. via debugfs:
"
$ echo auto > /sys/kernel/debug/dri/1/crtc-0/crc/control
$ cat /sys/kernel/debug/dri/1/crtc-0/crc/data
0x0000408c 0xa4e5cdd8
0x0000408d 0x72f537b4
"
The per-frame CRC can be used by userspace e.g. during automated testing,
to verify that whatever buffer was sent to be scanned out was actually
scanned out of the LCDIF correctly.
Acked-by: Lucas Stach <l.stach@pengutronix.de> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexander Stein <alexander.stein@ew.tq-group.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Robby Cai <robby.cai@nxp.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Stefan Agner <stefan@agner.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20220429212313.305556-1-marex@denx.de
Christian König [Tue, 3 May 2022 08:59:35 +0000 (10:59 +0200)]
drm/nouveau: remove trace_dma_fence_emit
Hardware drivers which don't have much difference between emit and init
shouldn't use this trace point.
Signed-off-by: Christian König <christian.koenig@amd.com> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Karol Herbst <kherbst@redhat.com> Cc: Lyude Paul <lyude@redhat.com> Cc: nouveau@lists.freedesktop.org Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220503085935.11023-1-christian.koenig@amd.com
Lyude Paul [Fri, 29 Apr 2022 19:53:47 +0000 (15:53 -0400)]
drm/nouveau/subdev/bus: Ratelimit logging for fault errors
There's plenty of ways to fudge the GPU when developing on nouveau by
mistake, some of which can result in nouveau seriously spamming dmesg with
fault errors. This can be somewhat annoying, as it can quickly overrun the
message buffer (or your terminal emulator's buffer) and get rid of actually
useful feedback from the driver. While working on my new atomic only MST
branch, I ran into this issue a couple of times.
So, let's fix this by adding nvkm_error_ratelimited(), and using it to
ratelimit errors from faults. This should be fine for developers, since
it's nearly always only the first few faults that we care about seeing.
Plus, you can turn off rate limiting in the kernel if you really need to.
Guo Zhengkui [Wed, 4 May 2022 16:09:29 +0000 (00:09 +0800)]
drm/nouveau/devinit: fix returnvar.cocci warnings
Fix the following coccicheck warnings:
drivers/gpu/drm/nouveau/nvkm/subdev/devinit/gf100.c:71:5-12:
Unneeded variable: "disable". Return "0ULL" on line 90.
drivers/gpu/drm/nouveau/nvkm/subdev/devinit/gm107.c:35:5-12:
Unneeded variable: "disable". Return "0ULL" on line 44.
drivers/gpu/drm/nouveau/nvkm/subdev/devinit/g98.c:35:5-12:
Unneeded variable: "disable". Return "0ULL" on line 50.
Jagan Teki [Thu, 28 Apr 2022 09:48:08 +0000 (15:18 +0530)]
drm: exynos: dsi: Use child panel or bridge find helpers
commit <d3f302ed41db> ("drm: exynos: dsi: Use drm panel_bridge API")
added devm_drm_of_get_bridge for looking up if child node has panel
or bridge.
However commit <3f58f7e086a1> ("Revert "drm: of: Lookup if child node
has panel or bridge") has reverted panel or bridge child node lookup
from devm_drm_of_get_bridge which eventually failed to find the DSI
devices in exynos drm dsi driver.
So, use the conventional child panel bridge lookup helpers like it
does before.
Jagan Teki [Fri, 29 Apr 2022 08:59:47 +0000 (14:29 +0530)]
Revert "drm: bridge: mcde_dsi: Switch to devm_drm_of_get_bridge"
commit <24a5f3ea84d9> ("drm: bridge: mcde_dsi: Switch to devm_drm_of_get_bridge")
switched to devm_drm_of_get_bridge for looking up if child node has panel
or bridge.
However commit <3f58f7e086a1> ("Revert "drm: of: Lookup if child node
has panel or bridge") has reverted panel or bridge child node lookup
from devm_drm_of_get_bridge as it breaks the non-trivial cases the
first child node might not be a panel or bridge.
So, revert this commit to switch the previous behavior of looking up
child panel or bridge.
Jagan Teki [Fri, 29 Apr 2022 08:59:46 +0000 (14:29 +0530)]
Revert "drm: bridge: mcde_dsi: Drop explicit bridge remove"
commit <90a30d4c0741> ("drm: bridge: mcde_dsi: Drop explicit bridge
remove") has removed downstream bridge as it's prior commit <24a5f3ea84d9>
("drm: bridge: mcde_dsi: Switch to devm_drm_of_get_bridge") added
devm_drm_of_get_bridge for looking up if child node has panel or bridge.
However commit <3f58f7e086a1> ("Revert "drm: of: Lookup if child node
has panel or bridge") has reverted panel or bridge child node lookup
from devm_drm_of_get_bridge as it breaks the non-trivial cases the
first child node might not be a panel or bridge.
So, revert this commit to switch the previous behavior of looking up
child panel or bridge.
Lucas Stach [Wed, 4 May 2022 09:02:29 +0000 (11:02 +0200)]
drm/etnaviv: avoid cleaning up sched_job when submit succeeded
While the labels may mislead the casual reader, the tail of the function
etnaviv_ioctl_gem_submit is always executed, as a lot of the structures
set up in this function need to be cleaned up regardless of whether the
submit succeeded or failed.
An exception is the newly added drm_sched_job_cleanup, which must only
be called when the submit failed before handing the job to the
scheduler.
Andy Yan [Fri, 22 Apr 2022 07:28:39 +0000 (09:28 +0200)]
drm/rockchip: Add VOP2 driver
The VOP2 unit is found on Rockchip SoCs beginning with rk3566/rk3568.
It replaces the VOP unit found in the older Rockchip SoCs.
This driver has been derived from the downstream Rockchip Kernel and
heavily modified:
- All nonstandard DRM properties have been removed
- dropped struct vop2_plane_state and pass around less data between
functions
- Dropped all DRM_FORMAT_* not known on upstream
- rework register access to get rid of excessively used macros
- Drop all waiting for framesyncs
The driver is tested with HDMI and MIPI-DSI display on a RK3568-EVB
board. Overlay support is tested with the modetest utility. AFBC support
on the cluster windows is tested with weston-simple-dmabuf-egl on
weston using the (yet to be upstreamed) panfrost driver support.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com> Co-Developed-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
[dt-binding-header:] Acked-by: Rob Herring <robh@kernel.org>
[moved dt-binding header from dt-nodes patch to here
and made checkpatch --strict happier] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220422072841.2206452-23-s.hauer@pengutronix.de
Current port description doesn't cover all possible cases. It currently
expects one single port with two endpoints.
When the HDMI connector is described in the device tree there can be two
ports, first one going to the VOP and the second one going to the connector.
Also on SoCs which only have a single VOP there will be only one
endpoint instead of two.
This patch addresses both issues. With this there can either be a single
port ("port") , or two of them ("port@0", "port@1") when the connector
is also in the device tree. Also the first or only port can either have
one endpoint ("endpoint") for single VOP SoCs or two ("endpoint@0",
"endpoint@1") for dual VOP SoCs.
dt-bindings: display: rockchip: Add binding for VOP2
The VOP2 is found on newer Rockchip SoCs like the rk3568 or the rk3566.
The binding differs slightly from the existing VOP binding, so add a new
binding file for it.
drm/simpledrm: Use fbdev defaults for shadow buffering
Don't select shadow buffering for the fbdev console explicitly. The
fbdev emulation's heuristic will enable it for any framebuffer with
.dirty callback.
fbdev: Use pageref offset for deferred-I/O writeback
Use pageref->offset instead of page->index for deferred-I/O writeback
where appropriate. Distinguishes between file-mapping offset and video-
memory offset. While at it, also remove unnecessary references to
struct page.
Fbdev's deferred-I/O code uses the two related page->index and
pageref->offset. The former is the page offset in the mapped file,
the latter is the byte offset in the video memory (or fbdev screen
buffer). It's the same value for fbdev drivers, but for DRM the values
can be different. Because GEM buffer objects are mapped at an offset
in the DRM device file, page->index has this offset added to it as well.
We currently don't hit this case in DRM, because all affected mappings
of GEM memory are performed with an internal, intermediate shadow buffer.
The value of page->index is required by page_mkclean(), which we
call to reset the mappings during the writeback phase of the deferred
I/O. The value of pageref->offset is for conveniently getting an offset
into video memory in fb helpers.
fbdev: Rename pagelist to pagereflist for deferred I/O
Rename various instances of pagelist to pagereflist. The list now
stores pageref structures, so the new name is more appropriate.
In their write-back helpers, several fbdev drivers refer to the
pageref list in struct fb_deferred_io instead of using the one
supplied as argument to the function. Convert them over to the
supplied one. It's the same instance, so no change of behavior
occurs.
Store the per-page state for fbdev's deferred I/O in struct
fb_deferred_io_pageref. Maintain a list of pagerefs for the pages
that have to be written back to video memory. Update all affected
drivers.
As with pages before, fbdev acquires a pageref when an mmaped page
of the framebuffer is being written to. It holds the pageref in a
list of all currently written pagerefs until it flushes the written
pages to video memory. Writeback occurs periodically. After writeback
fbdev releases all pagerefs and builds up a new dirty list until the
next writeback occurs.
Using pagerefs has a number of benefits.
For pages of the framebuffer, the deferred I/O code used struct
page.lru as an entry into the list of dirty pages. The lru field is
owned by the page cache, which makes deferred I/O incompatible with
some memory pages (e.g., most notably DRM's GEM SHMEM allocator).
struct fb_deferred_io_pageref now provides an entry into a list of
dirty framebuffer pages, freeing lru for use with the page cache.
Drivers also assumed that struct page.index is the page offset into
the framebuffer. This is not true for DRM buffers, which are located
at various offset within a mapped area. struct fb_deferred_io_pageref
explicitly stores an offset into the framebuffer. struct page.index
is now only the page offset into the mapped area.
These changes will allow DRM to use fbdev deferred I/O without an
intermediate shadow buffer.
v3:
* use pageref->offset for sorting
* fix grammar in comment
v2:
* minor fixes in commit message
The fbdev mmap function fb_mmap() unconditionally overrides the
driver's implementation if deferred I/O has been activated. This
makes it hard to implement mmap with anything but a vmalloc()'ed
software buffer. That is specifically a problem for DRM, where
video memory is maintained by a memory manager.
Leave the mmap handling to drivers and expect them to call the
helper for deferred I/O by thmeselves.
v4:
* unlock mm_lock in fb_mmap() error path (Dan)
v3:
* fix warning if fb_mmap is missing (kernel test robot)
v2:
* print a helpful error message if the defio setup is
incorrect (Javier)
drm/ast: Create the driver for ASPEED proprietory Display-Port
V1:
1. The MCU FW controling ASPEED DP is loaded by BMC boot loader.
2. Driver starts after CR[3:1] == 111b that indicates Tx is ASTDP,
and CRD1[5] has been asserted by BMVC boot loader.
3. EDID is prioritized by DP monitor.
4. DP's EDID has high priority to decide resolution supporting.
V2:
Modules description:
1. ASTDP (ASPEED DisplayPort) is controlled by dedicated
AST-MCU (ASPEED propriatary MCU).
2. MCU is looping in charged of HPD, Read EDID, Link Training with
DP sink.
3. ASTDP and AST-MUC reside in BMC (Baseboard Management controller)
addressing-space.
4. ASPEED DRM driver requests MCU to get HPD and EDID by CR-scratched
register.
Booting sequence:
1. Check if TX is ASTDP // ast_dp_launch()
2. Check if DP-MCU FW has loaded // ast_dp_launch()
3. Read EDID // ast_dp_read_edid()
4. Resolution switch // ast_dp_SetOutput()
V3:
1. Remove unneeded semicolon.
2. Apply to git://anongit.freedesktop.org/drm/drm, instead of
git://anongit.freedesktop.org/drm/drm-misc
3. Resolve auto build test WARNINGs on V1 patch.
V4:
1. Sync code-base with kernel 5.17_rc6
2. Remove the define of DPControlPower, because DP chips need to be
powered on to be used.
3. Remove the switches of PHY and Display from EDID procedure.
4. Revise increaing delay to fixed delay, because this version kernel
doesn't detect minitor consistenntly.
5. Create clean-up code used for reset of power state on errors with
-EIO manner.
6. Revise the DP detection by TX type and its DP-FW status during
booting and resume.
7. Correct the CamelCase Style.
8. Use register reading while needing, and remove to hold full
register.
9. Instead of 'u8', revise to 'bool' on swwitch of PHY and video.
10.Correct typo
11.Remove the duplicated copy of TX definition.
12.Use EDID_LENGTH as the constant of 128.
The RK3568 has HDMI_TX_AVDD0V9 and HDMI_TX_AVDD_1V8 supply inputs needed
for the HDMI port. add support for these to the driver for boards which
have them supplied by switchable regulators.
dt-bindings: display: rockchip: dw-hdmi: use "ref" as clock name
"vpll" is a misnomer. A clock input to a device should be named after
the usage in the device, not after the clock that drives it. On the
rk3568 the same clock is driven by the HPLL.
This patch adds "ref" as a new alternative clock name for "vpll"
drm/rockchip: dw_hdmi: rename vpll clock to reference clock
"vpll" is a misnomer. A clock input to a device should be named after
the usage in the device, not after the clock that drives it. On the
rk3568 the same clock is driven by the HPLL.
To fix that, this patch renames the vpll clock to ref clock. The clock
name "vpll" is left for compatibility to old device trees.
drm/rockchip: Add crtc_endpoint_id to rockchip_encoder
The VOP2 has an interface mux which decides to which encoder(s) a CRTC
is routed to. The encoders and CRTCs are connected via of_graphs in the
device tree. When given an encoder the VOP2 driver needs to know to
which internal register setting this encoder matches. For this the VOP2
binding offers different endpoints, one for each possible encoder. The
endpoint ids of these endpoints are used as a key from an encoders
device tree description to the internal register setting.
This patch adds the key aka endpoint id to struct rockchip_encoder plus
a function to read the endpoint id starting from the encoders device
node.
drm/rockchip: Embed drm_encoder into rockchip_decoder
The VOP2 driver needs rockchip specific information for a drm_encoder.
This patch creates a struct rockchip_encoder with a struct drm_encoder
embedded in it. This is used throughout the rockchip driver instead of
struct drm_encoder directly.
The information the VOP2 drivers needs is the of_graph endpoint node
of the encoder. To ease bisectability this is added here.
While at it convert the different encoder-to-driverdata macros to
static inline functions in order to gain type safety and readability.
Chen-Yu Tsai [Fri, 14 Jan 2022 07:40:38 +0000 (15:40 +0800)]
drm/rockchip: Support YUV formats with U/V swapped
The VOP in Rockchip SoCs that support YUV planes also support swapping
of the U and V elements. Supporting the swapped variants, especially
NV21, would be beneficial for multimedia applications, as the hardware
video decoders only output NV21, and supporting this pixel format in
the display pipeline would allow the decoded video frames to be output
directly.
Add support for this to support the various formats that have U/V
swapped.
José Expósito [Thu, 21 Apr 2022 17:07:23 +0000 (19:07 +0200)]
drm/rockchip: rk3066_hdmi: Replace drm_detect_hdmi_monitor() with is_hdmi
Once EDID is parsed, the monitor HDMI support information is available
through drm_display_info.is_hdmi.
This driver calls drm_detect_hdmi_monitor() to receive the same
information and stores its own cached value, which is less efficient.
Avoid calling drm_detect_hdmi_monitor() and use drm_display_info.is_hdmi
instead and also remove hdmi_data_info.sink_is_hdmi as it is no longer
necessary.
José Expósito [Thu, 21 Apr 2022 17:07:22 +0000 (19:07 +0200)]
drm/rockchip: inno_hdmi: Replace drm_detect_hdmi_monitor() with is_hdmi
Once EDID is parsed, the monitor HDMI support information is available
through drm_display_info.is_hdmi.
This driver calls drm_detect_hdmi_monitor() to receive the same
information and stores its own cached value, which is less efficient.
Avoid calling drm_detect_hdmi_monitor() and use drm_display_info.is_hdmi
instead and also remove hdmi_data_info.sink_is_hdmi as it is no longer
necessary.
Robin Murphy [Tue, 5 Apr 2022 14:32:50 +0000 (15:32 +0100)]
drm/rockchip: Refactor IOMMU initialisation
Defer the IOMMU domain setup until after successfully binding
components, so we can figure out IOMMU support directly from the VOP
devices themselves, rather than manually inferring it from the DT (which
also fails to account for whether the IOMMU driver is actually loaded).
Although this is somewhat of a logical cleanup, the main motivation is
to prepare for a change in the iommu_domain_alloc() interface.
Yang Yingliang [Fri, 22 Apr 2022 03:28:54 +0000 (11:28 +0800)]
drm/rockchip: vop: fix possible null-ptr-deref in vop_bind()
It will cause null-ptr-deref in resource_size(), if platform_get_resource()
returns NULL, move calling resource_size() after devm_ioremap_resource() that
will check 'res' to avoid null-ptr-deref.
drm/bridge: tfp410: Make tfp410_fini() return void
tfp410_fini() always returns zero. Make it return no value which makes it
easier to see in the callers that there is no error to handle.
Also the return value of i2c and platform driver remove callbacks is
ignored anyway. This prepares making i2c and platform remove callbacks
return void, too.
The i.MX8MP contains two syscon registers which are responsible
for configuring the on-SoC DPI-to-LVDS serializer. Implement a
simple bridge driver for this serializer.
--
- Add sentinel of_device_table
- Add RB from Sam
- Rename to fsl-ldb altogether
Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Peng Fan <peng.fan@nxp.com> Cc: Robby Cai <robby.cai@nxp.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
V2: - Rename syscon to fsl,syscon
V3: - Consistently use MX8MP
V4: - Fix MODULE_DESCRIPTION to also use MX8MP Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220426193645.244792-2-marex@denx.de
The i.MX8MP contains two syscon registers which are responsible
for configuring the on-SoC DPI-to-LVDS serializer. Add DT binding
which represents this serializer as a bridge.
Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Peng Fan <peng.fan@nxp.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Robby Cai <robby.cai@nxp.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: devicetree@vger.kernel.org
To: dri-devel@lists.freedesktop.org Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220426193645.244792-1-marex@denx.de
drm: bridge: adv7511: use non-legacy mode for CEC RX
The ADV7511 family of bridges supports two modes for CEC RX: legacy and
non-legacy mode. The only difference is whether the chip uses a single
CEC RX buffer, or uses all three available RX buffers. Currently the
adv7511 driver uses legacy mode.
While debugging a stall in CEC RX on an ADV7535, we reached out to
Analog Devices, who suggested to use non-legacy mode instead. According
to the programming guide for the ADV7511 [1], and the register control
manual of the ADV7535 [2], this is the default behaviour on reset. As
previously stated, the adv7511 driver currently overrides this to legacy
mode.
This patch updates the adv7511 driver to instead use non-legacy mode
with all three CEC RX buffers. As a result of this change, we no longer
experience any stalling of CEC RX with the ADV7535. It is not known why
non-legacy mode solves this particular issue, but besides this, no
functional change is to be expected by this patch. Please note that this
has only been tested on an ADV7535.
What follows is a brief description of the non-legacy mode interrupt
handling behaviour. The programming guide in [1] gives a more detailed
explanation.
With three RX buffers, the interrupt handler checks the CEC_RX_STATUS
register (renamed from CEC_RX_ENABLE in this patch), which contains
2-bit psuedo-timestamps for each of the RX buffers. The RX timestamps
for each buffer represent the time of arrival for the CEC frame held in
a given buffer, with lower timestamp values indicating chronologically
older frames. A special value of 0 indicates that the given RX buffer
is inactive and should be skipped. The interrupt handler parses these
timestamps and then reads the active RX buffers in the prescribed order
using the same logic as before. Changes have been made to ensure that
the correct RX buffer is cleared after processing. This clearing
procesure also sets the timestamp of the given RX buffer to 0 to mark it
as inactive.
[1] https://www.analog.com/media/en/technical-documentation/user-guides/ADV7511_Programming_Guide.pdf
cf. CEC Map, register 0x4A, bit 3, default value 1:
0 = Use only buffer 0 to store CEC frames (Legacy mode)
1 = Use all 3 buffers to stores the CEC frames (Non-legacy mode)
[2] The ADV7535 register control manual is under NDA, but trust me when
I say that non-legacy CEC RX mode is the default here too. Here the
register is offset by 0x70 and has an address of 0xBA in the DSI_CEC
regiser map.
drm: bridge: adv7511: enable CEC support for ADV7535
Like the ADV7533, the ADV7535 has an offset for the CEC register map,
and it is the same value (ADV7533_REG_CEC_OFFSET = 0x70).
Rather than testing for numerous chip types in the offset calculations
throughout the driver, just compute it during driver probe and put it in
the private adv7511 data structure.
Pin-Yen Lin [Mon, 25 Apr 2022 13:44:24 +0000 (21:44 +0800)]
drm/bridge: it6505: Send DPCD SET_POWER to downstream
Send DPCD SET_POWER command to downstream in .atomic_disable to make the
downstream monitor enter the power down mode, so the device suspend won't
be affected.
Christian König [Thu, 21 Apr 2022 18:20:49 +0000 (20:20 +0200)]
drm: handle kernel fences in drm_gem_plane_helper_prepare_fb v2
drm_gem_plane_helper_prepare_fb() was using
drm_atomic_set_fence_for_plane() which ignores all implicit fences when an
explicit fence is already set. That's rather unfortunate when the fb still
has a kernel fence we need to wait for to avoid presenting garbage on the
screen.
So instead update the fence in the plane state directly. While at it also
take care of all potential GEM objects and not just the first one.
Also remove the now unused drm_atomic_set_fence_for_plane() function, new
drivers should probably use the atomic helpers directly.
v2: improve kerneldoc, use local variable and num_planes, WARN_ON_ONCE
on missing planes.
Linus Torvalds [Sun, 1 May 2022 18:49:32 +0000 (11:49 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Take care of faults occuring between the PARange and IPA range by
injecting an exception
- Fix S2 faults taken from a host EL0 in protected mode
- Work around Oops caused by a PMU access from a 32bit guest when PMU
has been created. This is a temporary bodge until we fix it for
good.
x86:
- Fix potential races when walking host page table
- Fix shadow page table leak when KVM runs nested
- Work around bug in userspace when KVM synthesizes leaf 0x80000021
on older (pre-EPYC) or Intel processors
Generic (but affects only RISC-V):
- Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: work around QEMU issue with synthetic CPUID leaves
Revert "x86/mm: Introduce lookup_address_in_mm()"
KVM: x86/mmu: fix potential races when walking host page table
KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDR
KVM: arm64: Inject exception on out-of-IPA-range translation fault
KVM/arm64: Don't emulate a PMU for 32-bit guests if feature not set
KVM: arm64: Handle host stage-2 faults from 32-bit EL0
Linus Torvalds [Sun, 1 May 2022 17:03:36 +0000 (10:03 -0700)]
Merge tag 'x86_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- A fix to disable PCI/MSI[-X] masking for XEN_HVM guests as that is
solely controlled by the hypervisor
- A build fix to make the function prototype (__warn()) as visible as
the definition itself
- A bunch of objtool annotation fixes which have accumulated over time
- An ORC unwinder fix to handle bad input gracefully
- Well, we thought the microcode gets loaded in time in order to
restore the microcode-emulated MSRs but we thought wrong. So there's
a fix for that to have the ordering done properly
- Add new Intel model numbers
- A spelling fix
* tag 'x86_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guests
bug: Have __warn() prototype defined unconditionally
x86/Kconfig: fix the spelling of 'becoming' in X86_KERNEL_IBT config
objtool: Use offstr() to print address of missing ENDBR
objtool: Print data address for "!ENDBR" data warnings
x86/xen: Add ANNOTATE_NOENDBR to startup_xen()
x86/uaccess: Add ENDBR to __put_user_nocheck*()
x86/retpoline: Add ANNOTATE_NOENDBR for retpolines
x86/static_call: Add ANNOTATE_NOENDBR to static call trampoline
objtool: Enable unreachable warnings for CLANG LTO
x86,objtool: Explicitly mark idtentry_body()s tail REACHABLE
x86,objtool: Mark cpu_startup_entry() __noreturn
x86,xen,objtool: Add UNWIND hint
lib/strn*,objtool: Enforce user_access_begin() rules
MAINTAINERS: Add x86 unwinding entry
x86/unwind/orc: Recheck address range after stack info was updated
x86/cpu: Load microcode during restore_processor_state()
x86/cpu: Add new Alderlake and Raptorlake CPU model numbers
Linus Torvalds [Sun, 1 May 2022 16:34:54 +0000 (09:34 -0700)]
Merge tag 'objtool_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Borislav Petkov:
"A bunch of objtool fixes to improve unwinding, sibling call detection,
fallthrough detection and relocation handling of weak symbols when the
toolchain strips section symbols"
* tag 'objtool_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix code relocs vs weak symbols
objtool: Fix type of reloc::addend
objtool: Fix function fallthrough detection for vmlinux
objtool: Fix sibling call detection in alternatives
objtool: Don't set 'jump_dest' for sibling calls
x86/uaccess: Don't jump between functions
Linus Torvalds [Sun, 1 May 2022 16:30:47 +0000 (09:30 -0700)]
Merge tag 'irq_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
- Fix locking when accessing device MSI descriptors
* tag 'irq_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bus: fsl-mc-msi: Fix MSI descriptor mutex lock for msi_first_desc()
Merge tag 'driver-core-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some small driver core and kernfs fixes for some reported
problems. They include:
- kernfs regression that is causing oopses in 5.17 and newer releases
- topology sysfs fixes for a few small reported problems.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: fix NULL dereferencing in kernfs_remove
topology: Fix up build warning in topology_is_visible()
arch_topology: Do not set llc_sibling if llc_id is invalid
topology: make core_mask include at least cluster_siblings
topology/sysfs: Hide PPIN on systems that do not support it.
Merge tag 'usb-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.18-rc5 for some
reported issues and new quirks. They include:
- dwc3 driver fixes
- xhci driver fixes
- typec driver fixes
- new usb-serial driver ids
- added new USB devices to existing quirk tables
- other tiny fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (31 commits)
usb: phy: generic: Get the vbus supply
usb: dwc3: gadget: Return proper request status
usb: dwc3: pci: add support for the Intel Meteor Lake-P
usb: dwc3: core: Only handle soft-reset in DCTL
usb: gadget: configfs: clear deactivation flag in configfs_composite_unbind()
usb: misc: eud: Fix an error handling path in eud_probe()
usb: core: Don't hold the device lock while sleeping in do_proc_control()
usb: dwc3: Try usb-role-switch first in dwc3_drd_init
usb: dwc3: core: Fix tx/rx threshold settings
usb: mtu3: fix USB 3.0 dual-role-switch from device to host
xhci: Enable runtime PM on second Alderlake controller
usb: dwc3: fix backwards compat with rockchip devices
dt-bindings: usb: samsung,exynos-usb2: add missing required reg
usb: misc: fix improper handling of refcount in uss720_probe()
USB: Fix ehci infinite suspend-resume loop issue in zhaoxin
usb: typec: tcpm: Fix undefined behavior due to shift overflowing the constant
usb: typec: rt1719: Fix build error without CONFIG_POWER_SUPPLY
usb: typec: ucsi: Fix role swapping
usb: typec: ucsi: Fix reuse of completion structure
usb: xhci: tegra:Fix PM usage reference leak of tegra_xusb_unpowergate_partitions
...
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One fix for an endless error loop with the target driver affecting
tapes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target: pscsi: Set SCF_TREAT_READ_AS_NORMAL flag only if there is valid data
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A semi-large pile of clk driver fixes this time around.
Nothing is touching the core so these fixes are fairly well contained
to specific devices that use these clk drivers.
- Some Allwinner SoC fixes to gracefully handle errors and mark an
RTC clk as critical so that the RTC keeps ticking.
- Fix AXI bus clks and RTC clk design for Microchip PolarFire SoC
driver introduced this cycle. This has some devicetree bits acked
by riscv maintainers. We're fixing it now so that the prior
bindings aren't released in a major kernel version.
- Remove a reset on Microchip PolarFire SoCs that broke when enabling
CONFIG_PM.
- Set a min/max for the Qualcomm graphics clk. This got broken by the
clk rate range patches introduced this cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()
clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical
riscv: dts: microchip: reparent mpfs clocks
clk: microchip: mpfs: add RTCREF clock control
clk: microchip: mpfs: re-parent the configurable clocks
dt-bindings: rtc: add refclk to mpfs-rtc
dt-bindings: clk: mpfs: add defines for two new clocks
dt-bindings: clk: mpfs document msspll dri registers
riscv: dts: microchip: fix usage of fic clocks on mpfs
clk: microchip: mpfs: mark CLK_ATHENA as critical
clk: microchip: mpfs: fix parents for FIC clocks
clk: qcom: clk-rcg2: fix gfx3d frequency calculation
clk: microchip: mpfs: don't reset disabled peripherals
clk: sunxi-ng: fix not NULL terminated coccicheck error
Merge tag 'block-5.18-2022-04-29' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Revert of a patch that caused timestamp issues (Tejun)
- iocost warning fix (Tejun)
- bfq warning fix (Jan)
* tag 'block-5.18-2022-04-29' of git://git.kernel.dk/linux-block:
bfq: Fix warning in bfqq_request_over_limit()
Revert "block: inherit request start time from bio for BLK_CGROUP"
iocost: don't reset the inuse weight of under-weighted debtors
Merge tag 'io_uring-5.18-2022-04-29' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Pretty boring:
- three patches just adding reserved field checks (me, Eugene)
- Fixing a potential regression with IOPOLL caused by a block change
(Joseph)"
Boring is good.
* tag 'io_uring-5.18-2022-04-29' of git://git.kernel.dk/linux-block:
io_uring: check that data field is 0 in ringfd unregister
io_uring: fix uninitialized field in rw io_kiocb
io_uring: check reserved fields for recv/recvmsg
io_uring: check reserved fields for send/sendmsg
Merge tag 'random-5.18-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- Eric noticed that the memmove() in crng_fast_key_erasure() was bogus,
so this has been changed to a memcpy() and the confusing situation
clarified with a detailed comment.
- [Half]SipHash documentation updates from Bagas and Eric, after Eric
pointed out that the use of HalfSipHash in random.c made a bit of the
text potentially misleading.
* tag 'random-5.18-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
Documentation: siphash: disambiguate HalfSipHash algorithm from hsiphash functions
Documentation: siphash: enclose HalfSipHash usage example in the literal block
Documentation: siphash: convert danger note to warning for HalfSipHash
random: document crng_fast_key_erasure() destination possibility
Merge tag 'ceph-for-5.18-rc5' of https://github.com/ceph/ceph-client
Pull ceph client fixes from Ilya Dryomov:
"A fix for a NULL dereference that turns out to be easily triggerable
by fsync (marked for stable) and a false positive WARN and snap_rwsem
locking fixups"
* tag 'ceph-for-5.18-rc5' of https://github.com/ceph/ceph-client:
ceph: fix possible NULL pointer dereference for req->r_session
ceph: remove incorrect session state check
ceph: get snap_rwsem read lock in handle_cap_export for ceph_add_cap
libceph: disambiguate cluster/pool full log message
Revert "arm: dts: at91: Fix boolean properties with values"
This reverts commit 802b13607600, which caused another regression
as the pinctrl code actually expects an integer value of 0 or 1
rather than a simple boolean property.
Paolo Bonzini [Fri, 29 Apr 2022 18:43:04 +0000 (14:43 -0400)]
KVM: x86: work around QEMU issue with synthetic CPUID leaves
Synthesizing AMD leaves up to 0x80000021 caused problems with QEMU,
which assumes the *host* CPUID[0x80000000].EAX is higher or equal
to what KVM_GET_SUPPORTED_CPUID reports.
This causes QEMU to issue bogus host CPUIDs when preparing the input
to KVM_SET_CPUID2. It can even get into an infinite loop, which is
only terminated by an abort():
cpuid_data is full, no space for cpuid(eax:0x8000001d,ecx:0x3e)
To work around this, only synthesize those leaves if 0x8000001d exists
on the host. The synthetic 0x80000021 leaf is mostly useful on Zen2,
which satisfies the condition.
Fixes: d6dd57e0c4a3 ("KVM: x86: synthesize CPUID leaf 0x80000021h if useful") Reported-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- ARM SPE (Statistical Profiling Extensions) address fixes, for
synthesized events and for SPE events with physical addresses. Add a
simple 'perf test' entry to make sure this doesn't regress.
- Remove arch specific processing of kallsyms data to fixup symbol end
address, fixing excessive memory consumption in the annotation code.
* tag 'perf-tools-fixes-for-v5.18-2022-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf symbol: Remove arch__symbols__fixup_end()
perf symbol: Update symbols__fixup_end()
perf symbol: Pass is_kallsyms to symbols__fixup_end()
perf test: Add perf_event_attr test for Arm SPE
perf arm-spe: Fix SPE events with phys addresses
perf arm-spe: Fix addresses of synthesized SPE events
perf intel-pt: Fix timeless decoding with perf.data directory
Merge tag 'riscv-for-linus-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A fix to properly ensure a single CPU is running during patch_text().
- A defconfig update to include RPMSG_CTRL when RPMSG_CHAR was set,
necessary after a recent refactoring.
* tag 'riscv-for-linus-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: configs: Configs that had RPMSG_CHAR now get RPMSG_CTRL
riscv: patch_text: Fixup last cpu should be master
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Rename and reallocate the PT_ARM_MEMTAG_MTE ELF segment type.
This is a fix to the MTE ELF ABI for a bug that was added during the
most recent merge window as part of the coredump support.
The issue is that the value assigned to the new PT_ARM_MEMTAG_MTE
segment type has already been allocated to PT_AARCH64_UNWIND by the
ELF ABI, so we've bumped the value and changed the name of the
identifier to be better aligned with the existing one"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
elf: Fix the arm64 MTE ELF segment name and value
Drop lookup_address_in_mm() now that KVM is providing it's own variant
of lookup_address_in_pgd() that is safe for use with user addresses, e.g.
guards against page tables being torn down. A variant that provides a
non-init mm is inherently dangerous and flawed, as the only reason to use
an mm other than init_mm is to walk a userspace mapping, and
lookup_address_in_pgd() does not play nice with userspace mappings, e.g.
doesn't disable IRQs to block TLB shootdowns and doesn't use READ_ONCE()
to ensure an upper level entry isn't converted to a huge page between
checking the PAGE_SIZE bit and grabbing the address of the next level
down.
KVM: x86/mmu: fix potential races when walking host page table
KVM uses lookup_address_in_mm() to detect the hugepage size that the host
uses to map a pfn. The function suffers from several issues:
- no usage of READ_ONCE(*). This allows multiple dereference of the same
page table entry. The TOCTOU problem because of that may cause KVM to
incorrectly treat a newly generated leaf entry as a nonleaf one, and
dereference the content by using its pfn value.
- the information returned does not match what KVM needs; for non-present
entries it returns the level at which the walk was terminated, as long
as the entry is not 'none'. KVM needs level information of only 'present'
entries, otherwise it may regard a non-present PXE entry as a present
large page mapping.
- the function is not safe for mappings that can be torn down, because it
does not disable IRQs and because it returns a PTE pointer which is never
safe to dereference after the function returns.
So implement the logic for walking host page tables directly in KVM, and
stop using lookup_address_in_mm().
Cc: Sean Christopherson <seanjc@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Mingwei Zhang <mizhang@google.com>
Message-Id: <20220429031757.2042406-1-mizhang@google.com>
[Inline in host_pfn_mapping_level, ensure no semantic change for its
callers. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Fri, 22 Apr 2022 10:30:13 +0000 (12:30 +0200)]
KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
When KVM_EXIT_SYSTEM_EVENT was introduced, it included a flags
member that at the time was unused. Unfortunately this extensibility
mechanism has several issues:
- x86 is not writing the member, so it would not be possible to use it
on x86 except for new events
- the member is not aligned to 64 bits, so the definition of the
uAPI struct is incorrect for 32- on 64-bit userspace. This is a
problem for RISC-V, which supports CONFIG_KVM_COMPAT, but fortunately
usage of flags was only introduced in 5.18.
Since padding has to be introduced, place a new field in there
that tells if the flags field is valid. To allow further extensibility,
in fact, change flags to an array of 16 values, and store how many
of the values are valid. The availability of the new ndata field
is tied to a system capability; all architectures are changed to
fill in the field.
To avoid breaking compilation of userspace that was using the flags
field, provide a userspace-only union to overlap flags with data[0].
The new field is placed at the same offset for both 32- and 64-bit
userspace.
Cc: Will Deacon <will@kernel.org> Cc: Marc Zyngier <maz@kernel.org> Cc: Peter Gonda <pgonda@google.com> Cc: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reported-by: kernel test robot <lkp@intel.com>
Message-Id: <20220422103013.34832-1-pbonzini@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDR
Disallow memslots and MMIO SPTEs whose gpa range would exceed the host's
MAXPHYADDR, i.e. don't create SPTEs for gfns that exceed host.MAXPHYADDR.
The TDP MMU bounds its zapping based on host.MAXPHYADDR, and so if the
guest, possibly with help from userspace, manages to coerce KVM into
creating a SPTE for an "impossible" gfn, KVM will leak the associated
shadow pages (page tables):
On bare metal, encountering an impossible gpa in the page fault path is
well and truly impossible, barring CPU bugs, as the CPU will signal #PF
during the gva=>gpa translation (or a similar failure when stuffing a
physical address into e.g. the VMCS/VMCB). But if KVM is running as a VM
itself, the MAXPHYADDR enumerated to KVM may not be the actual MAXPHYADDR
of the underlying hardware, in which case the hardware will not fault on
the illegal-from-KVM's-perspective gpa.
Alternatively, KVM could continue allowing the dodgy behavior and simply
zap the max possible range. But, for hosts with MAXPHYADDR < 52, that's
a (minor) waste of cycles, and more importantly, KVM can't reasonably
support impossible memslots when running on bare metal (or with an
accurate MAXPHYADDR as a VM). Note, limiting the overhead by checking if
KVM is running as a guest is not a safe option as the host isn't required
to announce itself to the guest in any way, e.g. doesn't need to set the
HYPERVISOR CPUID bit.
A second alternative to disallowing the memslot behavior would be to
disallow creating a VM with guest.MAXPHYADDR > host.MAXPHYADDR. That
restriction is undesirable as there are legitimate use cases for doing
so, e.g. using the highest host.MAXPHYADDR out of a pool of heterogeneous
systems so that VMs can be migrated between hosts with different
MAXPHYADDRs without running afoul of the allow_smaller_maxphyaddr mess.
Note that any guest.MAXPHYADDR is valid with shadow paging, and it is
even useful in order to test KVM with MAXPHYADDR=52 (i.e. without
any reserved physical address bits).
The now common kvm_mmu_max_gfn() is inclusive instead of exclusive.
The memslot and TDP MMU code want an exclusive value, but the name
implies the returned value is inclusive, and the MMIO path needs an
inclusive check.
Fixes: 56d8cae20031 ("kvm: x86/mmu: Support zapping SPTEs in the TDP MMU") Fixes: 649661b38868 ("KVM: x86/mmu: Don't leak non-leaf SPTEs when zapping all SPTEs") Cc: stable@vger.kernel.org Cc: Maxim Levitsky <mlevitsk@redhat.com> Cc: Ben Gardon <bgardon@google.com> Cc: David Matlack <dmatlack@google.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220428233416.2446833-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge tag 'tegra-for-5.18-arm-defconfig-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
ARM: tegra: Default configuration fixes for v5.18
This contains two updates to the default configuration needed because of
a Kconfig symbol name change. This fixes a failure that was detected in
the NVIDIA automated test farm.
* tag 'tegra-for-5.18-arm-defconfig-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: config: multi v7: Enable NVIDIA Tegra video decoder driver
ARM: tegra_defconfig: Update CONFIG_TEGRA_VDE option
Merge tag 'imx-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.18, 2nd round:
- Fix one sparse warning on imx-weim driver.
- Fix vqmmc regulator to get UHS-I mode work on imx6ull-colibri board.
- Add missing 32.768 kHz PMIC clock for imx8mn-ddr4-evk board to fix
bd718xx-clk probe error.
* tag 'imx-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
ARM: dts: imx6ull-colibri: fix vqmmc regulator
bus: imx-weim: make symbol 'weim_of_notifier' static
Merge tag 'sunxi-fixes-for-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Fix return value in RSB bus driver
* tag 'sunxi-fixes-for-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
Marek Vasut [Thu, 28 Apr 2022 21:31:32 +0000 (23:31 +0200)]
drm/bridge: tc358767: Fix (e)DP bridge endpoint parsing in dedicated function
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP
port is optional. In case this port is not described in DT, the bridge
driver operates in DPI-to-DP mode. The drm_of_find_panel_or_bridge()
call in tc_probe_edp_bridge_endpoint() returns -ENODEV in case port@2
is not present in DT and this specific return value is incorrectly
propagated outside of tc_probe_edp_bridge_endpoint() function. All
other error values must be propagated and are propagated correctly.
Return 0 in case the port@2 is missing instead, that reinstates the
original behavior before the commit this patch fixes.
Fixes: d82fd3bf8271 ("drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated function") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Marek Vasut <marex@denx.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220428213132.447890-1-marex@denx.de
projects / kernel.git / log