Nina Schiff [Fri, 20 Nov 2015 20:31:39 +0000 (12:31 -0800)]
cgroups: Allow dynamically changing net_classid
The classid of a process is changed either when a process is moved to
or from a cgroup or when the net_cls.classid file is updated.
Previously net_cls only supported propogating these changes to the
cgroup's related sockets when a process was added or removed from the
cgroup. This means it was neccessary to remove and re-add all processes
to a cgroup in order to update its classid. This change introduces
support for doing this dynamically - i.e. when the value is changed in
the net_cls_classid file, this will also trigger an update to the
classid associated with all sockets controlled by the cgroup.
This mimics the behaviour of other cgroup subsystems.
net_prio circumvents this issue by storing an index into a table with
each socket (and so any updates to the table, don't require updating
the value associated with the socket). net_cls, however, passes the
socket the classid directly, and so this additional step is needed.
Signed-off-by: Nina Schiff <ninasc@fb.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Shaohui Xie [Fri, 20 Nov 2015 03:54:08 +0000 (11:54 +0800)]
net: fsl: expands dependencies of NET_VENDOR_FREESCALE
Freescale hosts some ARMv8 based SoCs, and a generic convention
ARCH_LAYERSCAPE is used to cover such SoCs. Adding ARCH_LAYERSCAPE
to dependencies of NET_VENDOR_FREESCALE to support networking on those
SoCs.
The ARCH_LAYERSCAPE is introduced by:
commit: b3d354ce8 arm64: Use generic Layerscape SoC family naming
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ip6mr: fix static mfc/dev leaks on table destruction
Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.
Fixes: 4c0e9d8cc1e9 ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code") CC: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipmr: fix static mfc/dev leaks on table destruction
When destroying an mrt table the static mfc entries and the static
devices are kept, which leads to devices that can never be destroyed
(because of refcnt taken) and leaked memory, for example:
unreferenced object 0xffff880034c144c0 (size 192):
comm "mfc-broken", pid 4777, jiffies 4320349055 (age 46001.964s)
hex dump (first 32 bytes):
98 53 f0 34 00 88 ff ff 98 53 f0 34 00 88 ff ff .S.4.....S.4....
ef 0a 0a 14 01 02 03 04 00 00 00 00 01 00 00 00 ................
backtrace:
[<ffffffff815c1b9e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff811ea6e0>] kmem_cache_alloc+0x190/0x300
[<ffffffff815931cb>] ip_mroute_setsockopt+0x5cb/0x910
[<ffffffff8153d575>] do_ip_setsockopt.isra.11+0x105/0xff0
[<ffffffff8153e490>] ip_setsockopt+0x30/0xa0
[<ffffffff81564e13>] raw_setsockopt+0x33/0x90
[<ffffffff814d1e14>] sock_common_setsockopt+0x14/0x20
[<ffffffff814d0b51>] SyS_setsockopt+0x71/0xc0
[<ffffffff815cdbf6>] entry_SYSCALL_64_fastpath+0x16/0x7a
[<ffffffffffffffff>] 0xffffffffffffffff
Make sure that everything is cleaned on netns destruction.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Further investigation showed that this can happen when an *odd* number of
fds are being passed over AF_UNIX sockets.
In these cases CMSG_LEN(i * sizeof(int)) and CMSG_SPACE(i * sizeof(int)),
where i is the number of successfully passed fds, differ by 4 bytes due
to the extra CMSG_ALIGN() padding in CMSG_SPACE() to an 8 byte boundary
on 64 bit. The padding is used to align subsequent cmsg headers in the
control buffer.
When the control buffer passed in from the receiver side *lacks* these 4
bytes (e.g. due to buggy/wrong API usage), then msg->msg_controllen will
overflow in scm_detach_fds():
int cmlen = CMSG_LEN(i * sizeof(int)); <--- cmlen w/o tail-padding
err = put_user(SOL_SOCKET, &cm->cmsg_level);
if (!err)
err = put_user(SCM_RIGHTS, &cm->cmsg_type);
if (!err)
err = put_user(cmlen, &cm->cmsg_len);
if (!err) {
cmlen = CMSG_SPACE(i * sizeof(int)); <--- cmlen w/ 4 byte extra tail-padding
msg->msg_control += cmlen;
msg->msg_controllen -= cmlen; <--- iff no tail-padding space here ...
} ... wrap-around
F.e. it will wrap to a length of 18446744073709551612 bytes in case the
receiver passed in msg->msg_controllen of 20 bytes, and the sender
properly transferred 1 fd to the receiver, so that its CMSG_LEN results
in 20 bytes and CMSG_SPACE in 24 bytes.
In case of MSG_CMSG_COMPAT (scm_detach_fds_compat()), I haven't seen an
issue in my tests as alignment seems always on 4 byte boundary. Same
should be in case of native 32 bit, where we end up with 4 byte boundaries
as well.
In practice, passing msg->msg_controllen of 20 to recvmsg() while receiving
a single fd would mean that on successful return, msg->msg_controllen is
being set by the kernel to 24 bytes instead, thus more than the input
buffer advertised. It could f.e. become an issue if such application later
on zeroes or copies the control buffer based on the returned msg->msg_controllen
elsewhere.
Maximum number of fds we can send is a hard upper limit SCM_MAX_FD (253).
Going over the code, it seems like msg->msg_controllen is not being read
after scm_detach_fds() in scm_recv() anymore by the kernel, good!
Relevant recvmsg() handler are unix_dgram_recvmsg() (unix_seqpacket_recvmsg())
and unix_stream_recvmsg(). Both return back to their recvmsg() caller,
and ___sys_recvmsg() places the updated length, that is, new msg_control -
old msg_control pointer into msg->msg_controllen (hence the 24 bytes seen
in the example).
Long time ago, Wei Yongjun fixed something related in commit e204aa5c95bb
("[NET]: Fix function put_cmsg() which may cause usr application memory
overflow").
RFC3542, section 20.2. says:
The fields shown as "XX" are possible padding, between the cmsghdr
structure and the data, and between the data and the next cmsghdr
structure, if required by the implementation. While sending an
application may or may not include padding at the end of last
ancillary data in msg_controllen and implementations must accept both
as valid. On receiving a portable application must provide space for
padding at the end of the last ancillary data as implementations may
copy out the padding at the end of the control message buffer and
include it in the received msg_controllen. When recvmsg() is called
if msg_controllen is too small for all the ancillary data items
including any trailing padding after the last item an implementation
may set MSG_CTRUNC.
Since we didn't place MSG_CTRUNC for already quite a long time, just do
the same as in e204aa5c95bb to avoid an overflow.
Btw, even man-page author got this wrong :/ See db939c9b26e9 ("cmsg.3: Fix
error in SCM_RIGHTS code sample"). Some people must have copied this (?),
thus it got triggered in the wild (reported several times during boot by
David and HacKurx).
No Fixes tag this time as pre 2002 (that is, pre history tree).
Reported-by: David Sterba <dave@jikos.cz> Reported-by: HacKurx <hackurx@gmail.com> Cc: PaX Team <pageexec@freemail.hu> Cc: Emese Revfy <re.emese@gmail.com> Cc: Brad Spengler <spender@grsecurity.net> Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Cc: Eric Dumazet <edumazet@google.com> Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy [Thu, 19 Nov 2015 19:12:50 +0000 (14:12 -0500)]
tipc: correct settings of broadcast link state
Since commit 623a20fb0d1a0e4582 ("tipc: let broadcast packet
reception use new link receive function") the broadcast send
link state was meant to always be set to LINK_ESTABLISHED, since
we don't need this link to follow the regular link FSM rules. It
was also the intention that this state anyway shouldn't impact
the run-time working state of the link, since the latter in
reality is controlled by the number of registered peers.
We have now discovered that this assumption is not quite correct.
If the broadcast link is reset because of too many retransmissions,
its state will inadvertently go to LINK_RESETTING, and never go
back to LINK_ESTABLISHED, because the LINK_FAILURE event was not
anticipated. This will work well once, but if it happens a second
time, the reset on a link in LINK_RESETTING has has no effect, and
neither the broadcast link nor the unicast links will go down as
they should.
Furthermore, it is confusing that the management tool shows that
this link is in UP state when that obviously isn't the case.
We now ensure that this state strictly follows the true working
state of the link. The state is set to LINK_ESTABLISHED when
the number of peers is non-zero, and to LINK_RESET otherwise.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Måns Rullgård [Thu, 19 Nov 2015 13:02:59 +0000 (13:02 +0000)]
net: ethernet: add driver for Aurora VLSI NB8800 Ethernet controller
This adds a driver for the Aurora VLSI NB8800 Ethernet controller.
It is an almost complete rewrite of a driver originally found in
a Sigma Designs 2.6.22 tree.
Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is the last remaining warning for arm64, and I'd like to get rid of
it. We don't really know the cache line size, architecturally it would
be at least 16 bytes, but all implementations I found have 64 or 128
bytes. Configuring tulip for 32-byte lines as we do on ARM32 seems to
be the safe but slow default, and nobody who cares about performance these
days would use a tulip chip anyway, so we can just use that.
To save the next person the job of trying to find out what this is for
and picking a default for their architecture just to kill off the warning,
I'm now removing the preprocessor #warning and turning it into a pr_warn
or dev_warn that prints the equivalent information when the driver gets
loaded.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Thu, 19 Nov 2015 09:56:51 +0000 (11:56 +0200)]
bnx2x: Fix vxlan removal
Commmit a9d6e6e697d7b "bnx2x: track vxlan port count" contains a bug -
Instead of achieving the required goal, vxlan configuration would not
be removed since we're decrementing the port instead of the counter.
CC: Jiri Benc <jbenc@redhat.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 19 Nov 2015 05:03:33 +0000 (21:03 -0800)]
tcp: fix potential huge kmalloc() calls in TCP_REPAIR
tcp_send_rcvq() is used for re-injecting data into tcp receive queue.
Problems :
- No check against size is performed, allowed user to fool kernel in
attempting very large memory allocations, eventually triggering
OOM when memory is fragmented.
- In case of fault during the copy we do not return correct errno.
Lets use alloc_skb_with_frags() to cook optimal skbs.
Fixes: b65d4e9c26ab ("tcp: Move rcvq sending to tcp_input.c") Fixes: b3170ab227ef ("tcp: Repair socket queues") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Pavel Emelyanov <xemul@parallels.com> Acked-by: Pavel Emelyanov <xemul@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 19 Nov 2015 02:17:31 +0000 (18:17 -0800)]
tcp: fix Fast Open snmp over-counting bug
Fix incrementing TCPFastOpenActiveFailed snmp stats multiple times
when the handshake experiences multiple SYN timeouts.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng [Thu, 19 Nov 2015 02:17:30 +0000 (18:17 -0800)]
tcp: disable Fast Open on timeouts after handshake
Some middle-boxes black-hole the data after the Fast Open handshake
(https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf).
The exact reason is unknown. The work-around is to disable Fast Open
temporarily after multiple recurring timeouts with few or no data
delivered in the established state.
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Thu, 19 Nov 2015 01:27:25 +0000 (17:27 -0800)]
net: cpsw: Fix ethernet regression for dm814x
Commit ed62d9163a5f ("drivers: net: cpsw: davinci_emac: move reading mac
id to common file") started using of_machine_is_compatible for detecting
type but missed at dm8148 causing Ethernet to stop working.
Let's fix the issue by adding handling for dm814x.
Cc: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Mugunthnan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 18 Nov 2015 20:40:13 +0000 (12:40 -0800)]
tcp: md5: fix lockdep annotation
When a passive TCP is created, we eventually call tcp_md5_do_add()
with sk pointing to the child. It is not owner by the user yet (we
will add this socket into listener accept queue a bit later anyway)
But we do own the spinlock, so amend the lockdep annotation to avoid
following splat :
Fixes: 551ceaaab60e1 ("tcp: md5: protects md5sig_info with RCU") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Wed, 18 Nov 2015 20:13:07 +0000 (21:13 +0100)]
net: qmi_wwan: add XS Stick W100-2 from 4G Systems
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
Sergei Shtylyov [Wed, 18 Nov 2015 22:39:51 +0000 (01:39 +0300)]
ravb: fix WARNING in __free_irq()
When the R8A7795 support was added to the driver, little attention was paid
to the ravb_open() error path: free_irq() for the EMAC interrupt was called
uncoditionally, unlike request_irq(), and in a wrong order as well...
As a result, on the R-Car gen2 SoCs I started getting the following in case
of a device opening error:
Fix up the free_irq() call order and add a new label on the error path.
Fixes: 379026306719 ("ravb: Add support for r8a7795 SoC") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Aya Mahfouz [Wed, 18 Nov 2015 06:36:44 +0000 (08:36 +0200)]
net: dns_resolver: convert time_t to time64_t
Changes the definition of the pointer _expiry from time_t to
time64_t. This is to handle the Y2038 problem where time_t
will overflow in the year 2038. The change is safe because
the kernel subsystems that call dns_query pass NULL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 18 Nov 2015 15:40:19 +0000 (16:40 +0100)]
net/ip6_tunnel: fix dst leak
the commit 7443dd3f74b8 ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel")
introduced percpu storage for ip6_tunnel dst cache, but while clearing
such cache it used raw_cpu_ptr to walk the per cpu entries, so cached
dst on non current cpu are not actually reset.
This patch replaces raw_cpu_ptr with per_cpu_ptr, properly cleaning
such storage.
Fixes: 7443dd3f74b8 ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Pope [Wed, 18 Nov 2015 01:21:07 +0000 (18:21 -0700)]
ethernet/atheros/alx: add Killer E2400 device ID
This patch adds the PCI device ID (0xe0a1) and alx_pci_tbl entry for the
Killer E2400 Ethernet controller, modeled after the Killer E2200
controller support (0xe091) already present in the alx driver.
This patch was originally authored by Ben Pope, but it got held up by
issues in the commit message, so I'm resubmitting it on his behalf.
I've extensively used a kernel with this patch on a System76 serw9
laptop and am quite confident it works well (at least on the hardware I
have available for testing).
Note that as a favor to System76, Ubuntu has been carrying this as a
sauce patch in their 4.2 based Wily kernel, which presumably has given
it real-world testing on other E2400 equipped hardware (I don't know of
any Ubuntu kernel bugs filed about it):
Signed-off-by: Jason Gerard DeRose <jason@system76.com> Signed-off-by: Ben Pope <benpope81@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 18 Nov 2015 16:59:29 +0000 (08:59 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Assorted bug fixes, the mlock2 system call gets added, and one
improvement. The boot from dasd devices is now possible from a wider
range of devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: remove SALIPL loader
s390: wire up mlock2 system call
s390: remove g5 elf platform support
s390: avoid cache aliasing under z/VM and KVM
s390/sclp: _sclp_wait_int(): retain full PSW mask
s390/zcrypt: Fix initialisation when zcrypt is built-in
s390/zcrypt: Fix kernel crash on systems without AP bus support
s390: add support for ipl devices in subchannel sets > 0
s390/ipl: fix out of bounds access in scpdata_write
s390/pci_dma: improve debugging of errors during dma map
s390/pci_dma: handle dma table failures
s390/pci_dma: unify label of invalid translation table entries
s390/syscalls: remove system call number calculation
s390/cio: simplify css_generate_pgid
s390/diag: add a s390 prefix to the diagnose trace point
s390/head: fix error message on unsupported hardware
Linus Torvalds [Wed, 18 Nov 2015 16:43:29 +0000 (08:43 -0800)]
Merge tag 'hwmon-for-linus-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix build issues in scpi and ina2xx drivers, update scpi driver to
support recent firmware, and fix an uninitialized variable warning in
applesmc driver"
1) Fix list tests in netfilter ingress support, from Florian Westphal.
2) Fix reversal of input and output interfaces in ingress hook
invocation, from Pablo Neira Ayuso.
3) We have a use after free in r8169, caught by Dave Jones, fixed by
Francois Romieu.
4) Splice use-after-free fix in AF_UNIX frmo Hannes Frederic Sowa.
5) Three ipv6 route handling bug fixes from Martin KaFai Lau:
a) Don't create clone routes not managed by the fib6 tree
b) Don't forget to check expiration of DST_NOCACHE routes.
c) Handle rt->dst.from == NULL properly.
6) Several AF_PACKET fixes wrt transport header setting and SKB
protocol setting, from Daniel Borkmann.
7) Fix thunder driver crash on shutdown, from Pavel Fedin.
8) Several Mellanox driver fixes (max MTU calculations, use of correct
DMA unmap in TX path, etc.) from Saeed Mahameed, Tariq Toukan, Doron
Tsur, Achiad Shochat, Eran Ben Elisha, and Noa Osherovich.
9) Several mv88e6060 DSA driver fixes (wrong bit definitions for
certain registers, etc.) from Neil Armstrong.
10) Make sure to disable preemption while updating per-cpu stats of ip
tunnels, from Jason A. Donenfeld.
11) Various ARM64 bpf JIT fixes, from Yang Shi.
12) Flush icache properly in ARM JITs, from Daniel Borkmann.
13) Fix masking of RX and TX interrupts in ravb driver, from Masaru
Nagai.
14) Fix netdev feature propagation for devices not implementing
->ndo_set_features(). From Nikolay Aleksandrov.
15) Big endian fix in vmxnet3 driver, from Shrikrishna Khare.
16) RAW socket code increments incorrect SNMP counters, fix from Ben
Cartwright-Cox.
17) IPv6 multicast SNMP counters are bumped twice, fix from Neil Horman.
18) Fix handling of VLAN headers on stacked devices when REORDER is
disabled. From Vlad Yasevich.
19) Fix SKB leaks and use-after-free in ipvlan and macvlan drivers, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
MAINTAINERS: Update Mellanox's Eth NIC driver entries
net/core: revert "net: fix __netdev_update_features return.." and add comment
af_unix: take receive queue lock while appending new skb
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
net: use skb_clone to avoid alloc_pages failure.
packet: Use PAGE_ALIGNED macro
packet: Don't check frames_per_block against negative values
net: phy: Use interrupts when available in NOLINK state
phy: marvell: Add support for 88E1540 PHY
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
macvlan: fix leak in macvlan_handle_frame
ipvlan: fix use after free of skb
ipvlan: fix leak in ipvlan_rcv_frame
vlan: Do not put vlan headers back on bridge and macvlan ports
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
via-velocity: unconditionally drop frames with bad l2 length
ipg: Remove ipg driver
dl2k: Add support for IP1000A-based cards
snmp: Remove duplicate OUTMCAST stat increment
net: thunder: Check for driver data in nicvf_remove()
...
net/core: revert "net: fix __netdev_update_features return.." and add comment
This reverts commit 36204e334087 ("net: fix __netdev_update_features return
on ndo_set_features failure")
and adds a comment explaining why it's okay to return a value other than
0 upon error. Some drivers might actually change flags and return an
error so it's better to fire a spurious notification rather than miss
these.
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: take receive queue lock while appending new skb
While possibly in future we don't necessarily need to use
sk_buff_head.lock this is a rather larger change, as it affects the
af_unix fd garbage collector, diag and socket cleanups. This is too much
for a stable patch.
For the time being grab sk_buff_head.lock without disabling bh and irqs,
so don't use locked skb_queue_tail.
Fixes: a32cdd043ebf ("net: af_unix: implement stream sendpage support") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
rtnetlink: fix frame size warning in rtnl_fill_ifinfo
Fix the following warning:
CC net/core/rtnetlink.o
net/core/rtnetlink.c: In function ‘rtnl_fill_ifinfo’:
net/core/rtnetlink.c:1308:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
}
^
by splitting up the huge rtnl_fill_ifinfo into some smaller ones, so we
don't have the huge frame allocations at the same time.
Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Zhang [Tue, 17 Nov 2015 12:49:30 +0000 (20:49 +0800)]
net: use skb_clone to avoid alloc_pages failure.
1. new skb only need dst and ip address(v4 or v6).
2. skb_copy may need high order pages, which is very rare on long running server.
Signed-off-by: Junwei Zhang <linggao.zjw@alibaba-inc.com> Signed-off-by: Martin Zhang <martinbj2008@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Mon, 16 Nov 2015 22:36:46 +0000 (23:36 +0100)]
net: phy: Use interrupts when available in NOLINK state
The NOLINK state will poll the phy once a second to see if the link
has come up. If the phy has an interrupt line, this polling can be
skipped, since the phy should interrupt when the link returns.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E1540 can be found embedded in the Marvell 88E6352 switch. It
is compatible with the 88E1510, so add support for it, using the 88E1510 specific functions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Shi [Mon, 16 Nov 2015 22:35:35 +0000 (14:35 -0800)]
arm64: bpf: make BPF prologue and epilogue align with ARM64 AAPCS
Save and restore FP/LR in BPF prog prologue and epilogue, save SP to FP
in prologue in order to get the correct stack backtrace.
However, ARM64 JIT used FP (x29) as eBPF fp register, FP is subjected to
change during function call so it may cause the BPF prog stack base address
change too.
Use x25 to replace FP as BPF stack base register (fp). Since x25 is callee
saved register, so it will keep intact during function call.
It is initialized in BPF prog prologue when BPF prog is started to run
everytime. Save and restore x25/x26 in BPF prologue and epilogue to keep
them intact for the outside of BPF. Actually, x26 is unnecessary, but SP
requires 16 bytes alignment.
CC: Zi Shen Lim <zlim.lnx@gmail.com> CC: Xi Wang <xi.wang@gmail.com> Signed-off-by: Yang Shi <yang.shi@linaro.org> Acked-by: Zi Shen Lim <zlim.lnx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Mon, 16 Nov 2015 21:54:20 +0000 (22:54 +0100)]
macvlan: fix leak in macvlan_handle_frame
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 654704934aa8 ("net: introduce rx_handler results and logic around that") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Mon, 16 Nov 2015 21:44:53 +0000 (22:44 +0100)]
ipvlan: fix use after free of skb
ipvlan_handle_frame is a rx_handler, and when it returns a value other
than RX_HANDLER_CONSUMED (here, NET_RX_DROP aka RX_HANDLER_ANOTHER),
__netif_receive_skb_core expects that the skb still exists and will
process it further, but we just freed it.
Fixes: a346ddd1a0fb ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Mon, 16 Nov 2015 21:34:26 +0000 (22:34 +0100)]
ipvlan: fix leak in ipvlan_rcv_frame
Pass a **skb to ipvlan_rcv_frame so that if skb_share_check returns a
new skb, we actually use it during further processing.
It's safe to ignore the new skb in the ipvlan_xmit_* functions, because
they call ipvlan_rcv_frame with local == true, so that dev_forward_skb
is called and always takes ownership of the skb.
Fixes: a346ddd1a0fb ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 17 Nov 2015 19:38:36 +0000 (14:38 -0500)]
Merge branch 'vlan-reorder'
Vladislav Yasevich says:
====================
Fix issues with vlans without REORDER_HEADER
A while ago Phil Sutter brought up an issue with vlans without
REORDER_HEADER and bridges. The problem was that if a vlan
without REORDER_HEADER was a port in the bridge, the bridge ended
up forwarding corrupted packets that still contained the vlan header.
The same issue exists for bridge mode macvlan/macvtap devices.
An additional issue with vlans without REORDER_HEADER is that stacking
them also doesn't work. The reason here is that skb_reorder_vlan_header()
function assumes that it on ETH_HLEN bytes deep into the packet. That
is not the case, when you a vlan without REORRDER_HEADER flag set.
This series attempts to correct these 2 issues.
1) To solve the stacked vlans problem, the patch simply use
skb->mac_len as an offset to start copying mac addresses that
is part of header reordering.
2) To fix the issue with bridge/macvlan/macvtap, the second patch
simply doesn't write the vlan header back to the packet if the
vlan device is either a bridge or a macvlan port. This ends up
being the simplest and least performance intrussive solution.
I've considered extending patch 2 to all stacked devices (essentially
checked for the presense of rx_handler), but that feels like a broader
restriction and _may_ break existing uses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 16 Nov 2015 20:43:45 +0000 (15:43 -0500)]
vlan: Do not put vlan headers back on bridge and macvlan ports
When a vlan is configured with REORDER_HEADER set to 0, the vlan
header is put back into the packet and makes it appear that
the vlan header is still there even after it's been processed.
This posses a problem for bridge and macvlan ports. The packets
passed to those device may be forwarded and at the time of the
forward, vlan headers end up being unexpectedly present.
With the patch, we make sure that we do not put the vlan header
back (when REORDER_HEADER is 0) if a bridge or macvlan has
been configured on top of the vlan device.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Mon, 16 Nov 2015 20:43:44 +0000 (15:43 -0500)]
vlan: Fix untag operations of stacked vlans with REORDER_HEADER off
When we have multiple stacked vlan devices all of which have
turned off REORDER_HEADER flag, the untag operation does not
locate the ethernet addresses correctly for nested vlans.
The reason is that in case of REORDER_HEADER flag being off,
the outer vlan headers are put back and the mac_len is adjusted
to account for the presense of the header. Then, the subsequent
untag operation, for the next level vlan, always use VLAN_ETH_HLEN
to locate the begining of the ethernet header and that ends up
being a multiple of 4 bytes short of the actuall beginning
of the mac header (the multiple depending on the how many vlan
encapsulations ethere are).
As a reslult, if there are multiple levles of vlan devices
with REODER_HEADER being off, the recevied packets end up
being dropped.
To solve this, we use skb->mac_len as the offset. The value
is always set on receive path and starts out as a ETH_HLEN.
The value is also updated when the vlan header manupations occur
so we know it will be correct.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Timo Teräs [Mon, 16 Nov 2015 12:36:32 +0000 (14:36 +0200)]
via-velocity: unconditionally drop frames with bad l2 length
By default the driver allowed incorrect frames to be received. What is
worse the code does not handle very short frames correctly. The FCS
length is unconditionally subtracted, and the underflow can cause
skb_put to be called with large number after implicit cast to unsigned.
And indeed, an skb_over_panic() was observed with via-velocity.
This removes the module parameter as it does not work in it's
current state, and should be implemented via NETIF_F_RXALL if needed.
Suggested-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 17 Nov 2015 18:11:08 +0000 (10:11 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A fs-cache regression fix, and adding a warning about obnoxiou^W
moderation of list given in MAINTAINERS"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
MAINTAINERS: linux-cachefs@redhat.com is moderated for non-subscribers
FS-Cache: Add missing initialization of ret in cachefiles_write_page()
Larry Finger [Tue, 10 Nov 2015 16:46:11 +0000 (10:46 -0600)]
rtlwifi: rtl8821ae: Fix lockups on boot
In commit b99c6cd7d946b ("rtlwifi: rtl8821ae: Fix system lockups on boot"),
an attempt was made to fix a regression introduced in commit 711cfb529bee
("rtlwifi: Remove the clear interrupt routine from all drivers").
Unfortunately, there were logic errors in that patch that prevented
affected boxes from booting even after that patch was applied.
The actual cause of the original problem is unknown as none of the
developers have systems that are affected.
Fixes: b99c6cd7d946 ("rtlwifi: rtl8821ae: Fix system lockups on boot") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [V4.1+] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FS-Cache: Add missing initialization of ret in cachefiles_write_page()
fs/cachefiles/rdwr.c: In function ‘cachefiles_write_page’:
fs/cachefiles/rdwr.c:882: warning: ‘ret’ may be used uninitialized in
this function
If the jump to label "error" is taken, "ret" will indeed be
uninitialized, and random stack data may be printed by the debug code.
Fixes: 5d48261abfac8200 ("FS-Cache: Handle a write to the page immediately beyond the EOF marker") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Ondrej Zary [Sun, 15 Nov 2015 21:36:11 +0000 (22:36 +0100)]
dl2k: Add support for IP1000A-based cards
Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.
This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.
Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180
MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.
Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Mon, 16 Nov 2015 18:09:10 +0000 (13:09 -0500)]
snmp: Remove duplicate OUTMCAST stat increment
the OUTMCAST stat is double incremented, getting bumped once in the mcast code
itself, and again in the common ip output path. Remove the mcast bump, as its
not needed
Validated by the reporter, with good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Claus Jensen <claus.jensen@microsemi.com> CC: Claus Jensen <claus.jensen@microsemi.com> CC: David Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Fedin [Mon, 16 Nov 2015 14:51:34 +0000 (17:51 +0300)]
net: thunder: Check for driver data in nicvf_remove()
In some cases the crash is caused by nicvf_remove() being called from
outside. For example, if we try to feed the device to vfio after the
probe has failed for some reason. So, move the check to better place.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The ":" is supposed to be preceded by a driver name, but in this
case it is an empty string since the device has no parent.
There are many types of network devices without a parent. The
anonymous warnings for these devices can be hard to debug. Log
the network device name instead in these cases to assist further
debugging.
This is mostly similar to how __netdev_printk() handles orphan
devices.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
af_unix: don't append consumed skbs to sk_receive_queue
In case multiple writes to a unix stream socket race we could end up in a
situation where we pre-allocate a new skb for use in unix_stream_sendpage
but have to free it again in the locked section because another skb
has been appended meanwhile, which we must use. Accidentally we didn't
clear the pointer after consuming it and so we touched freed memory
while appending it to the sk_receive_queue. So, clear the pointer after
consuming the skb.
This bug has been found with syzkaller
(http://github.com/google/syzkaller) by Dmitry Vyukov.
Fixes: a32cdd043ebf ("net: af_unix: implement stream sendpage support") Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dragos Tatulea [Mon, 16 Nov 2015 09:52:48 +0000 (10:52 +0100)]
net: switchdev: fix return code of fdb_dump stub
rtnl_fdb_dump always expects an index to be returned by the ndo_fdb_dump op,
but when CONFIG_NET_SWITCHDEV is off, it returns an error.
Fix that by returning the given unmodified idx.
A similar fix was a09f3ab2eda8 ("switchdev: fix return value of
switchdev_port_fdb_dump in case of error") but for the CONFIG_NET_SWITCHDEV=y
case.
Fixes: 6fd659d1d1a8 ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops.") Signed-off-by: Dragos Tatulea <dragos@endocode.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 15 Nov 2015 13:02:16 +0000 (15:02 +0200)]
bnx2x: Fix VLANs null-pointer for 57710, 57711
Commit 9adc932e3eff "bnx2x: add vlan filtering offload" introduced
a regression in regard for vlans for 57710, 57711 adapters -
Loading 8021q module on a machine with such an adapter would cause
a null pointer dereference, as the driver mistakenly publishes it
has capabilities for vlan CTAG filtering.
Reported-by: Otto Sabart <osabart@redhat.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masaru Nagai [Sun, 15 Nov 2015 12:34:42 +0000 (21:34 +0900)]
ravb: remove unhandle int cause
This driver does not handle the AVB-DMAC Receive FIFO Warning interrupt
now, so the interrupt should not be enabled.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
raw: increment correct SNMP counters for ICMP messages
Sending ICMP packets with raw sockets ends up in the SNMP counters
logging the type as the first byte of the IPv4 header rather than
the ICMP header. This is fixed by adding the IP Header Length to
the casting into a icmphdr struct.
Signed-off-by: Ben Cartwright-Cox <ben@benjojo.co.uk> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: fix __netdev_update_features return on ndo_set_features failure
If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.
Fixes: 7ff4b771ac03 ("net: Call netdev_features_change() from netdev_update_features()") CC: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: fix feature changes on devices without ndo_set_features
When __netdev_update_features() was updated to ensure some features are
disabled on new lower devices, an error was introduced for devices which
don't have the ndo_set_features() method set. Before we'll just set the
new features, but now we return an error and don't set them. Fix this by
returning the old behaviour and setting err to 0 when ndo_set_features
is not present.
Fixes: 602907040ad5 ("net/core: ensure features get disabled on new lower devs") CC: Jarod Wilson <jarod@redhat.com> CC: Jiri Pirko <jiri@resnulli.us> CC: Ido Schimmel <idosch@mellanox.com> CC: Sander Eikelenboom <linux@eikelenboom.it> CC: Andy Gospodarek <gospo@cumulusnetworks.com> CC: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Andy Gospodarek <gospo@cumulusnetworks.com> Reviewed-by: Jarod Wilson <jarod@redhat.com> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Dave Young <dyoung@redhat.com> Tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Fri, 13 Nov 2015 10:36:57 +0000 (11:36 +0100)]
be2net: remove unused local rsstable array
Remove rsstable array and its initialization from be_set_rss_hash_opts().
The array became unused after "2cd9914 be2net: Support for configurable
RSS hash key". The initial RSS table is now filled and stored for later
usage during Rx queue creation.
Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Sathya Perla <sathya.perla@avagotech.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masaru Nagai [Fri, 13 Nov 2015 10:24:49 +0000 (19:24 +0900)]
ravb: Fix int mask value overwritten issue
When RX/TX interrupt for Network Control queue and Best Effort queue
is issued at the same time, the interrupt mask of Network Control
queue will be reset when the mask of Best Effort queue is set.
This patch fixes this problem.
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Fedin [Fri, 13 Nov 2015 06:46:59 +0000 (09:46 +0300)]
net: smsc911x: Reset PHY during initialization
On certain hardware after software reboot the chip may get stuck and fail
to reinitialize during reset. This can be fixed by ensuring that PHY is
reset too.
Old PHY resetting method required operational MDIO interface, therefore
the chip should have been already set up. In order to be able to function
during probe, it is changed to use PMT_CTRL register.
The problem could be observed on SMDK5410 board.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sat, 14 Nov 2015 00:16:18 +0000 (01:16 +0100)]
bpf, arm64: start flushing icache range from header
While recently going over ARM64's BPF code, I noticed that the icache
range we're flushing should start at header already and not at ctx.image.
Reason is that after 3aba6f9dd5f9 ("net: bpf: arm64: address randomize
and write protect JIT code"), we also want to make sure to flush the
random-sized trap in front of the start of the actual program (analogous
to x86). No operational differences from user side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Zi Shen Lim <zlim.lnx@gmail.com> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
ath10k: poll HTT send completion when CE 5 is unused
commit 2f52eb0f3f68 ("ath10k: configure copy engine 5 for HTT messages")
moved send completion polling under HTT Rx (CE 5) service routine. For
QCA6174 based devices copy engine 1 (CE 1) is used for HTT Rx instead
of CE 5. So send completion never be called. This is causing "failed to
transmit packet, dropping: -105" errors. Fix this by processing send
completion from CE 1 service routine instead of CE 5.
Fixes: 2f52eb0f3f68 ("ath10k: configure copy engine 5 for HTT messages") Tested-by: Ryan Hsu <ryanhsu@qca.qualcomm.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Daniel Borkmann [Sat, 14 Nov 2015 00:26:53 +0000 (01:26 +0100)]
bpf, arm: start flushing icache range from header
During review I noticed that the icache range we're flushing should
start at header already and not at ctx.image.
Reason is that after 65d9210e7720 ("net: bpf: arm: address randomize
and write protect JIT code"), we also want to make sure to flush the
random-sized trap in front of the start of the actual program (analogous
to x86). No operational differences from user side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Nicolas Schichan <nschichan@freebox.fr> Cc: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Shi [Thu, 12 Nov 2015 22:07:46 +0000 (14:07 -0800)]
bpf: samples: exclude asm/sysreg.h for arm64
commit 6bfdc2859e1642c84361372388c3abae74edf7cc
("arm64: kernel: Add support for Privileged Access Never") includes sysreg.h
into futex.h and uaccess.h. But, the inline assembly used by asm/sysreg.h is
incompatible with llvm so it will cause BPF samples build failure for ARM64.
Since sysreg.h is useless for BPF samples, just exclude it from Makefile via
defining __ASM_SYSREG_H.
Signed-off-by: Yang Shi <yang.shi@linaro.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Shi [Thu, 12 Nov 2015 21:57:00 +0000 (13:57 -0800)]
arm64: bpf: fix JIT frame pointer setup
BPF fp should point to the top of the BPF prog stack. The original
implementation made it point to the bottom incorrectly.
Move A64_SP to fp before reserve BPF prog stack space.
CC: Zi Shen Lim <zlim.lnx@gmail.com> CC: Xi Wang <xi.wang@gmail.com> Signed-off-by: Yang Shi <yang.shi@linaro.org> Reviewed-by: Zi Shen Lim <zlim.lnx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Måns Rullgård [Thu, 12 Nov 2015 18:41:12 +0000 (18:41 +0000)]
net: phy: vitesse: add support for VSC8601
This adds support for the Vitesse VSC8601 PHY. Generic functions are
used for everything except interrupt handling.
Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Måns Rullgård [Thu, 12 Nov 2015 17:40:20 +0000 (17:40 +0000)]
net: phy: at803x: support interrupt on 8030 and 8035
Commit 40b54cc10 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ip_tunnel: disable preemption when updating per-cpu tstats
Drivers like vxlan use the recently introduced
udp_tunnel_xmit_skb/udp_tunnel6_xmit_skb APIs. udp_tunnel6_xmit_skb
makes use of ip6tunnel_xmit, and ip6tunnel_xmit, after sending the
packet, updates the struct stats using the usual
u64_stats_update_begin/end calls on this_cpu_ptr(dev->tstats).
udp_tunnel_xmit_skb makes use of iptunnel_xmit, which doesn't touch
tstats, so drivers like vxlan, immediately after, call
iptunnel_xmit_stats, which does the same thing - calls
u64_stats_update_begin/end on this_cpu_ptr(dev->tstats).
While vxlan is probably fine (I don't know?), calling a similar function
from, say, an unbound workqueue, on a fully preemptable kernel causes
real issues:
The solution would be to protect the whole
this_cpu_ptr(dev->tstats)/u64_stats_update_begin/end blocks with
disabling preemption and then reenabling it.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Sudeep Holla [Wed, 28 Oct 2015 17:17:31 +0000 (17:17 +0000)]
hwmon: (scpi) skip unsupported sensors properly
Currently it's assumed that firmware exports only the class of sensors
supported by the driver. However with newer firmware or SCPI protocol
revision, support for newer classes of sensors can be present.
The driver fails to probe with the following warning if an unsupported
class of sensor is encountered in the firmware.
sysfs: cannot create duplicate filename
'/devices/platform/scpi/scpi:sensors/hwmon/hwmon0/'
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:31
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u12:0 Not tainted 4.3.0-rc7 #137
Hardware name: ARM Juno development board (r0) (DT)
Workqueue: deferwq deferred_probe_work_func
PC is at sysfs_warn_dup+0x54/0x78
LR is at sysfs_warn_dup+0x54/0x78
This patch fixes the above issue by skipping through the unsupported
class of SCPI sensors.
Fixes: 4ee4da6dea4f ("hwmon: Support thermal zones registration for SCP temperature sensors") Fixes: 1e18fcf663ac ("hwmon: Support sensors exported via ARM SCP interface") Cc: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Punit Agrawal <punit.agrawal@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Arnd Bergmann [Mon, 16 Nov 2015 16:56:39 +0000 (17:56 +0100)]
hwmon: (scpi) add thermal-of dependency
The newly added scpi thermal support is broken when the scpi driver
is built-in but the thermal driver is a loadable module:
drivers/built-in.o: In function `scpi_hwmon_probe':
(.text+0x444d70): undefined reference to `thermal_zone_of_sensor_unregister'
(.text+0x444d94): undefined reference to `thermal_zone_of_sensor_register'
drivers/built-in.o: In function `scpi_hwmon_remove':
(text+0x444e6c): undefined reference to `thermal_zone_of_sensor_unregister'
This uses the same Kconfig trick that we have in a couple of other
drivers already to ensure we can only select the driver in valid
configurations when either THERMAL_OF is disabled, or when with a
dependency on CONFIG_THERMAL that can force SCPI to be a loadable
module in the case I was hitting.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 4ee4da6dea4f ("hwmon: Support thermal zones registration for SCP temperature sensors") Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Heiko Carstens [Fri, 13 Nov 2015 13:17:14 +0000 (14:17 +0100)]
s390: remove SALIPL loader
There is no known user, therefore remove the code.
Acked-by: Rob Van Der Heij <robvdheij@nl.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit b16e61804089 ("s390: avoid z13 cache aliasing") checks for the
machine type to optimize address space randomization and zero page
allocation to avoid cache aliases.
This check might fail under a hypervisor with migration support.
z/VMs "Single System Image and Live Guest Relocation" facility will
"fake" the machine type of the oldest system in the group. For example
in a group of zEC12 and Z13 the guest appears to run on a zEC12
(architecture fencing within the relocation domain)
Remove the machine type detection and always use cache aliasing
rules that are known to work for all machines. These are the z13
aliasing rules.
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the following "maybe used uninitialized" warnings by
initializing the variables to keep the compiler quiet.
There is no "used uninitialized" in this case.
CC [M] drivers/hwmon/applesmc.o
drivers/hwmon/applesmc.c: In function ‘applesmc_init_smcreg’:
drivers/hwmon/applesmc.c:595:43: warning: ‘right_light_sensor’
may be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:26: note: ‘right_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
drivers/hwmon/applesmc.c:595:43: warning: ‘left_light_sensor’ may
be used uninitialized in this function [-Wmaybe-uninitialized]
s->num_light_sensors = left_light_sensor + right_light_sensor;
^
drivers/hwmon/applesmc.c:540:7: note: ‘left_light_sensor’ was
declared here
bool left_light_sensor, right_light_sensor;
^
Li Yang [Thu, 5 Nov 2015 20:18:17 +0000 (14:18 -0600)]
hwmon: (ina2xx) Fix build issue by selecting REGMAP_I2C
Since 8762e768ab7d ("hwmon: (ina2xx) convert driver to using regmap")
the driver requires REGMAP_I2C to build. Select it by default
in Kconfig.
Reported-by: Guo Chunrong <B40290@freescale.com> Cc: Marc Titinger <mtitinger@baylibre.com> Signed-off-by: Li Yang <leoli@freescale.com> Fixes: 8762e768ab7d ("hwmon: (ina2xx) convert driver to using regmap") Signed-off-by: Guenter Roeck <linux@roeck-us.net>
David S. Miller [Mon, 16 Nov 2015 01:16:26 +0000 (20:16 -0500)]
Merge branch 'mv88e6060-fixes'
Neil Armstrong says:
====================
net: dsa: mv88e6060: cleanup and fix setup
This patchset introduces some fixes and a registers addressing cleanup for
the mv88e6060 DSA driver.
The first patch removes the poll_link as mv88e6xxx.
The 3 following patches fixes the setup in regards of the datasheet.
The 2 last patches introduces a clean header and replaces all magic values.
To align with the mv88e6xxx code, add a similar header file
with all the register defines.
The file is based on the mv88e6xxx header for coherency.
Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong [Tue, 10 Nov 2015 15:51:32 +0000 (16:51 +0100)]
net: dsa: mv88e6060: use the correct bit shift for mac0
According to the mv88e6060 datasheet, the first mac byte must
be at position 9 instead of 8 since the bit 8 is used to select
if the mac address must differ for each port for Pause frames.
Use the correct shift and set the same mac address for all port.
Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong [Tue, 10 Nov 2015 15:51:24 +0000 (16:51 +0100)]
net: dsa: mv88e6060: use the correct MaxFrameSize bit
According to the mv88e6060 datasheet, the MaxFrameSize bit position
is 10 instead of 11 which is reserved.
Use the bit correctly to setup max frame size to 1536.
Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong [Tue, 10 Nov 2015 15:51:19 +0000 (16:51 +0100)]
net: dsa: mv88e6060: use the correct InitReady bit
According to the mv88e6060 datasheet, the InitReady bit position
is 11 and the polarity is inverted.
Use the bit correctly to detect the end of initialization.
Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Armstrong [Tue, 10 Nov 2015 15:51:14 +0000 (16:51 +0100)]
net: dsa: mv88e6060: remove poll_link callback
As of mv88e6xxx remove the poll_link callback since the link
state change polling is now handled by the phylib.
Tested on a mv88e6060 B0 device with a TI DM816X SoC.
Suggested-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / kernel.git / log