Linus Torvalds [Mon, 1 Jun 2020 18:42:38 +0000 (11:42 -0700)]
Merge tag 'spi-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This has been a very active release for the DesignWare driver in
particular - after a long period of inactivity we have had a lot of
people actively working on it for unrelated reasons this cycle with
some of that work still not landed.
Otherwise it's been fairly quiet for the subsystem.
Highlights include:
- Lots of performance improvements and fixes for the DesignWare
driver from Serge Semin, Andy Shevchenko, Wan Ahmad Zainie, Clement
Leger, Dinh Nguyen and Jarkko Nikula.
- Support for octal mode transfers in spidev.
- Slave mode support for the Rockchip drivers.
- Support for AMD controllers, Broadcom mspi and Raspberry Pi 4, and
Intel Elkhart Lake"
* tag 'spi-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (125 commits)
spi: spi-fsl-dspi: fix native data copy
spi: Convert DW SPI binding to DT schema
spi: dw: Refactor mid_spi_dma_setup() to separate DMA and IRQ config
spi: dw: Make DMA request line assignments explicit for Intel Medfield
spi: bcm2835: Remove shared interrupt support
dt-bindings: snps,dw-apb-ssi: add optional reset property
spi: dw: add reset control
spi: bcm2835: Enable shared interrupt support
spi: bcm2835: Implement shutdown callback
spi: dw: Use regset32 DebugFS method to create regdump file
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Fix Rx-only DMA transfers
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
...
Linus Torvalds [Mon, 1 Jun 2020 18:39:37 +0000 (11:39 -0700)]
Merge tag 'regmap-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a very active release for the regmap API for some
reason, a lot of it due to new devices with odd requirements that can
sensibly be handled here.
- Add support for buses implementing a custom reg_update_bits()
method in case the bus has a native operation for this.
- Support 16 bit register addresses in SMBus.
- Allow customization of the device attached to regmap-irq.
- Helpers for bitfield operations and per-port field initializations"
* tag 'regmap-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: provide helpers for simple bit operations
regmap: add helper for per-port regfield initialization
regmap-i2c: add 16-bit width registers support
regmap: Simplify implementation of the regmap_field_read_poll_timeout() macro
regmap: Simplify implementation of the regmap_read_poll_timeout() macro
regmap: add reg_sequence helpers
regmap-irq: make it possible to add irq_chip do a specific device node
regmap: Add bus reg_update_bits() support
regmap: debugfs: check count when read regmap file
Linus Torvalds [Mon, 1 Jun 2020 18:33:40 +0000 (11:33 -0700)]
Merge tag 'hwmon-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Infrastructure:
- Add notification support
New drivers:
- Baikal-T1 PVT sensor driver
- amd_energy driver to report energy counters
- Driver for Maxim MAX16601
- Gateworks System Controller
Various:
- applesmc: avoid overlong udelay()
- dell-smm: Use one DMI match for all XPS models
- ina2xx: Implement alert functions
- lm70: Add support for ACPI
- lm75: Fix coding-style warnings
- lm90: Add max6654 support to lm90 driver
- nct7802: Replace container_of() API
- nct7904: Set default timeout
- nct7904: Add watchdog function
- pmbus: Improve initialization of 'currpage' and 'currphase'"
* tag 'hwmon-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (24 commits)
hwmon: Add Baikal-T1 PVT sensor driver
hwmon: Add notification support
dt-bindings: hwmon: Add Baikal-T1 PVT sensor binding
hwmon: (applesmc) avoid overlong udelay()
hwmon: (nct7904) Set default timeout
hwmon: (amd_energy) Missing platform_driver_unregister() on error in amd_energy_init()
MAINTAINERS: add entry for AMD energy driver
hwmon: (amd_energy) Add documentation
hwmon: Add amd_energy driver to report energy counters
hwmon: (nct7802) Replace container_of() API
hwmon: (lm90) Add max6654 support to lm90 driver
hwmon : (nct6775) Use kobj_to_dev() API
hwmon: (pmbus) Driver for Maxim MAX16601
hwmon: (pmbus) Improve initialization of 'currpage' and 'currphase'
hwmon: (adt7411) update contact email
hwmon: (lm75) Fix all coding-style warnings on lm75 driver
hwmon: Reduce indentation level in __hwmon_device_register()
hwmon: (ina2xx) Implement alert functions
hwmon: (lm70) Add support for ACPI
hwmon: (dell-smm) Use one DMI match for all XPS models
...
Linus Torvalds [Mon, 1 Jun 2020 18:30:28 +0000 (11:30 -0700)]
Merge tag 'tpmdd-next-20200522' of git://git.infradead.org/users/jjs/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen.
* tag 'tpmdd-next-20200522' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: eventlog: Replace zero-length array with flexible-array member
tpm/tpm_ftpm_tee: Use UUID API for exporting the UUID
Yes, staying withing 80 columns is certainly still _preferred_. But
it's not the hard limit that the checkpatch warnings imply, and other
concerns can most certainly dominate.
Increase the default limit to 100 characters. Not because 100
characters is some hard limit either, but that's certainly a "what are
you doing" kind of value and less likely to be about the occasional
slightly longer lines.
Miscellanea:
- to avoid unnecessary whitespace changes in files, checkpatch will no
longer emit a warning about line length when scanning files unless
--strict is also used
- Add a bit to coding-style about alignment to open parenthesis
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 31 May 2020 17:45:11 +0000 (10:45 -0700)]
Merge tag 'x86-urgent-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A pile of x86 fixes:
- Prevent a memory leak in ioperm which was caused by the stupid
assumption that the exit cleanup is always called for current,
which is not the case when fork fails after taking a reference on
the ioperm bitmap.
- Fix an arithmething overflow in the DMA code on 32bit systems
- Fill gaps in the xstate copy with defaults instead of leaving them
uninitialized
- Revert: "Make __X32_SYSCALL_BIT be unsigned long" as it turned out
that existing user space fails to build"
* tag 'x86-urgent-2020-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ioperm: Prevent a memory leak when fork fails
x86/dma: Fix max PFN arithmetic overflow on 32 bit systems
copy_xstate_to_kernel(): don't leave parts of destination uninitialized
x86/syscalls: Revert "x86/syscalls: Make __X32_SYSCALL_BIT be unsigned long"
14) Fix leak in inetdev_init(), from Yang Yingliang.
15) Don't try to use inet hash and unhash in l2tp code, results in
crashes. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (77 commits)
l2tp: add sk_family checks to l2tp_validate_socket
l2tp: do not use inet_hash()/inet_unhash()
net: qrtr: Allocate workqueue before kernel_bind
mptcp: remove msk from the token container at destruction time.
mptcp: fix race between MP_JOIN and close
mptcp: fix unblocking connect()
net/sched: act_ct: add nat mangle action only for NAT-conntrack
devinet: fix memleak in inetdev_init()
virtio_vsock: Fix race condition in virtio_transport_recv_pkt
drivers/net/ibmvnic: Update VNIC protocol version reporting
NFC: st21nfca: add missed kfree_skb() in an error path
neigh: fix ARP retransmit timer guard
bpf, selftests: Add a verifier test for assigning 32bit reg states to 64bit ones
bpf, selftests: Verifier bounds tests need to be updated
bpf: Fix a verifier issue when assigning 32bit reg states to 64bit ones
bpf: Fix use-after-free in fmod_ret check
net/mlx5e: replace EINVAL in mlx5e_flower_parse_meta()
net/mlx5e: Fix MLX5_TC_CT dependencies
net/mlx5e: Properly set default values when disabling adaptive moderation
net/mlx5e: Fix arch depending casting issue in FEC
...
Eric Dumazet [Fri, 29 May 2020 18:32:25 +0000 (11:32 -0700)]
l2tp: add sk_family checks to l2tp_validate_socket
syzbot was able to trigger a crash after using an ISDN socket
and fool l2tp.
Fix this by making sure the UDP socket is of the proper family.
BUG: KASAN: slab-out-of-bounds in setup_udp_tunnel_sock+0x465/0x540 net/ipv4/udp_tunnel.c:78
Write of size 1 at addr ffff88808ed0c590 by task syz-executor.5/3018
Memory state around the buggy address: ffff88808ed0c480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88808ed0c500: 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88808ed0c580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff88808ed0c600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88808ed0c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 228539feba0a ("l2tp: fix races in tunnel creation") Fixes: b2079113577e ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: James Chapman <jchapman@katalix.com> Cc: Guillaume Nault <gnault@redhat.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 29 May 2020 18:20:53 +0000 (11:20 -0700)]
l2tp: do not use inet_hash()/inet_unhash()
syzbot recently found a way to crash the kernel [1]
Issue here is that inet_hash() & inet_unhash() are currently
only meant to be used by TCP & DCCP, since only these protocols
provide the needed hashinfo pointer.
L2TP uses a single list (instead of a hash table)
This old bug became an issue after commit cf0204725308
("bpf: Add new cgroup attach type to enable sock modifications")
since after this commit, sk_common_release() can be called
while the L2TP socket is still considered 'hashed'.
Chris Lew [Thu, 28 May 2020 23:05:26 +0000 (16:05 -0700)]
net: qrtr: Allocate workqueue before kernel_bind
A null pointer dereference in qrtr_ns_data_ready() is seen if a client
opens a qrtr socket before qrtr_ns_init() can bind to the control port.
When the control port is bound, the ENETRESET error will be broadcasted
and clients will close their sockets. This results in DEL_CLIENT
packets being sent to the ns and qrtr_ns_data_ready() being called
without the workqueue being allocated.
Allocate the workqueue before setting sk_data_ready and binding to the
control port. This ensures that the work and workqueue structs are
allocated and initialized before qrtr_ns_data_ready can be called.
Fixes: 5d7341dac688 ("net: qrtr: Migrate nameservice to kernel from userspace") Signed-off-by: Chris Lew <clew@codeaurora.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 31 May 2020 04:39:13 +0000 (21:39 -0700)]
Merge branch 'mptcp-a-bunch-of-fixes'
Paolo Abeni says:
====================
mptcp: a bunch of fixes
This patch series pulls together a few bugfixes for MPTCP bug observed while
doing stress-test with apache bench - forced to use MPTCP and multiple
subflows.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 29 May 2020 15:43:31 +0000 (17:43 +0200)]
mptcp: remove msk from the token container at destruction time.
Currently we remote the msk from the token container only
via mptcp_close(). The MPTCP master socket can be destroyed
also via other paths (e.g. if not yet accepted, when shutting
down the listener socket). When we hit the latter scenario,
dangling msk references are left into the token container,
leading to memory corruption and/or UaF.
This change addresses the issue by moving the token removal
into the msk destructor.
Fixes: 763873e77a3e ("mptcp: Add key generation and token tree") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The MP_JOIN socket will be leaked. Additionally we can hit
UaF for the msk 'struct socket' referenced via the 'conn'
field.
This change try to address the issue introducing some
synchronization between the MP_JOIN 3whs and mptcp_close
via the join_list spinlock. If we detect the msk is closing
the MP_JOIN socket is closed, too.
Fixes: fb5f5519370c ("mptcp: Add handling of incoming MP_JOIN requests") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 29 May 2020 15:43:29 +0000 (17:43 +0200)]
mptcp: fix unblocking connect()
Currently unblocking connect() on MPTCP sockets fails frequently.
If mptcp_stream_connect() is invoked to complete a previously
attempted unblocking connection, it will still try to create
the first subflow via __mptcp_socket_create(). If the 3whs is
completed and the 'can_ack' flag is already set, the latter
will fail with -EINVAL.
This change addresses the issue checking for pending connect and
delegating the completion to the first subflow. Additionally
do msk addresses and sk_state changes only when needed.
Fixes: a4ba69e25e7d ("mptcp: Associate MPTCP context with TCP socket") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
wenxu [Sat, 30 May 2020 05:54:51 +0000 (13:54 +0800)]
net/sched: act_ct: add nat mangle action only for NAT-conntrack
Currently add nat mangle action with comparing invert and orig tuple.
It is better to check IPS_NAT_MASK flags first to avoid non necessary
memcmp for non-NAT conntrack.
Signed-off-by: wenxu <wenxu@ucloud.cn> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yang Yingliang [Sat, 30 May 2020 03:34:33 +0000 (11:34 +0800)]
devinet: fix memleak in inetdev_init()
When devinet_sysctl_register() failed, the memory allocated
in neigh_parms_alloc() should be freed.
Fixes: 680708aba816 ("ipv4: fail early when creating netdev named all or default") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The race condition is as follows:
Task1 Task2
===== =====
__sock_release virtio_transport_recv_pkt
__vsock_release vsock_find_bound_socket (found sk)
lock_sock_nested
vsock_remove_sock
sock_orphan
sk_set_socket(sk, NULL)
sk->sk_shutdown = SHUTDOWN_MASK
...
release_sock
lock_sock
virtio_transport_recv_connecting
sk->sk_socket->state (panic!)
The root cause is that vsock_find_bound_socket can't hold the lock_sock,
so there is a small race window between vsock_find_bound_socket() and
lock_sock(). If __vsock_release() is running in another task,
sk->sk_socket will be set to NULL inadvertently.
This fixes it by checking sk->sk_shutdown(suggested by Stefano) after
lock_sock since sk->sk_shutdown is set to SHUTDOWN_MASK under the
protection of lock_sock_nested.
Signed-off-by: Jia He <justin.he@arm.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 30 May 2020 19:28:44 +0000 (12:28 -0700)]
Merge tag 'powerpc-5.7-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- a fix for the recent change to how we restore non-volatile GPRs,
which broke our emulation of reading from the DSCR (Data Stream
Control Register).
- a fix for the recent rewrite of interrupt/syscall exit in C, we need
to exclude KCOV from that code, otherwise it can lead to
unrecoverable faults.
Thanks to Daniel Axtens.
* tag 'powerpc-5.7-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Disable sanitisers for C syscall/interrupt entry/exit code
powerpc/64s: Fix restore of NV GPRs after facility unavailable exception
Linus Torvalds [Sat, 30 May 2020 19:26:21 +0000 (12:26 -0700)]
Merge tag 'gpio-v5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here are some (very) late fixes for GPIO, none of them very serious
except the one tagged for stable for enabling IRQ on open drain lines:
- Fix probing of mvebu chips without PWM
- Fix error path on ida_get_simple() on the exar driver
- Notify userspace properly about line status changes when flags are
changed on lines.
- Fix a sleeping while holding spinlock in the mellanox driver.
- Fix return value of the PXA and Kona probe calls.
- Fix IRQ locking of open drain lines, it is fine to have IRQs on
open drain lines flagged for output"
* tag 'gpio-v5.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: fix locking open drain IRQ lines
gpio: bcm-kona: Fix return value of bcm_kona_gpio_probe()
gpio: pxa: Fix return value of pxa_gpio_probe()
gpio: mlxbf2: Fix sleeping while holding spinlock
gpiolib: notify user-space about line status changes after flags are set
gpio: exar: Fix bad handling for ida_simple_get error path
gpio: mvebu: Fix probing for chips without PWM
Thomas Falcon [Thu, 28 May 2020 16:19:17 +0000 (11:19 -0500)]
drivers/net/ibmvnic: Update VNIC protocol version reporting
VNIC protocol version is reported in big-endian format, but it
is not byteswapped before logging. Fix that, and remove version
comparison as only one protocol version exists at this time.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chuhong Yuan [Thu, 28 May 2020 10:20:37 +0000 (18:20 +0800)]
NFC: st21nfca: add missed kfree_skb() in an error path
st21nfca_tm_send_atr_res() misses to call kfree_skb() in an error path.
Add the missed function call to fix it.
Fixes: bbfda2328108 ("NFC: st21nfca: Adding P2P support to st21nfca in Initiator & Target mode") Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Thu, 28 May 2020 07:15:13 +0000 (15:15 +0800)]
neigh: fix ARP retransmit timer guard
In commit 5b68fd4c4205 ("neigh: support smaller retrans_time settting")
we add more accurate control for ARP and NS. But for ARP I forgot to
update the latest guard in neigh_timer_handler(), then the next
retransmit would be reset to jiffies + HZ/2 if we set the retrans_time
less than 500ms. Fix it by setting the time_before() check to HZ/100.
IPv6 does not have this issue.
Reported-by: Jianwen Ji <jiji@redhat.com> Fixes: 5b68fd4c4205 ("neigh: support smaller retrans_time settting") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 29 May 2020 23:31:22 +0000 (16:31 -0700)]
Merge tag 'mlx5-fixes-2020-05-28' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2020-05-28
This series introduces some fixes to mlx5 driver.
v1->v2:
- Fix bad sha1, Jakub.
- Added one more patch by Pablo.
net/mlx5e: replace EINVAL in mlx5e_flower_parse_meta()
Nothing major, the only patch worth mentioning is the suspend/resume crash
fix by adding the missing pci device handlers, the fix is very straight
forward and as Dexuan already expressed, the patch is important for Azure
users to avoid crash on VM hibernation, patch is marked for -stable v4.6
below.
Conflict note:
('net/mlx5e: Fix MLX5_TC_CT dependencies') has a trivial one line conflict
with current net-next, which can be resolved by simply using the line from
net-next.
Please pull and let me know if there is any problem.
For -stable v4.6
('net/mlx5: Fix crash upon suspend/resume')
For -stable v5.6
('net/mlx5e: replace EINVAL in mlx5e_flower_parse_meta()')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 29 May 2020 23:10:07 +0000 (16:10 -0700)]
Merge tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This time there is one fix for the error path in the mediatek cmdq
driver (used by their video driver) and a couple of devicetree fixes,
mostly for 32-bit ARM, and fairly harmless:
- On OMAP2 there were a few regressions in the ethernet drivers, one
of them leading to an external abort trap
- One Raspberry Pi version had a misconfigured LED
- Interrupts on Broadcom NSP were slightly misconfigured
- One i.MX6q board had issues with graphics mode setting
- On mmp3 there are some minor fixes that were submitted for v5.8
with a cc:stable tag, so I ended up picking them up here as well
- The Mediatek Video Codec needs to run at a higher frequency than
configured originally"
* tag 'armsoc-fixes-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: mmp3: Drop usb-nop-xceiv from HSIC phy
ARM: dts: mmp3-dell-ariel: Fix the SPI devices
ARM: dts: mmp3: Use the MMP3 compatible string for /clocks
ARM: dts: bcm: HR2: Fix PPI interrupt types
ARM: dts: bcm2835-rpi-zero-w: Fix led polarity
ARM: dts/imx6q-bx50v3: Set display interface clock parents
soc: mediatek: cmdq: return send msg error code
arm64: dts: mt8173: fix vcodec-enc clock
ARM: dts: Fix wrong mdio clock for dm814x
ARM: dts: am437x: fix networking on boards with ksz9031 phy
ARM: dts: am57xx: fix networking on boards with ksz9031 phy
ColdFire is a big-endian cpu with a big-endian dspi hw module,
so, it uses native access, but memcpy breaks the endianness.
So, if i understand properly, by native copy we would mean
be(cpu)->be(dspi) or le(cpu)->le(dspi) accesses, so my fix
shouldn't break anything, but i couldn't test it on LS family,
so every test is really appreciated.
Fixes: ae90bc286aee ("spi: spi-fsl-dspi: Simplify bytes_per_word gymnastics") Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com> Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20200529195756.184677-1-angelo.dureghello@timesys.com Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Fri, 29 May 2020 20:59:54 +0000 (13:59 -0700)]
Merge tag 'ceph-for-5.7-rc8' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"Cache tiering and cap handling fixups, both marked for stable"
* tag 'ceph-for-5.7-rc8' of git://github.com/ceph/ceph-client:
ceph: flush release queue when handling caps for unknown inode
libceph: ignore pool overlay and cache logic on redirects
Linus Torvalds [Fri, 29 May 2020 20:41:33 +0000 (13:41 -0700)]
Merge tag 'iommu-fixes-v5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Two build fixes for issues introduced during the merge window
- A fix for a reference count leak in an error path of
iommu_group_alloc()
* tag 'iommu-fixes-v5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Fix reference count leak in iommu_group_alloc.
x86: Hide the archdata.iommu field behind generic IOMMU_API
ia64: Hide the archdata.iommu field behind generic IOMMU_API
Linus Torvalds [Fri, 29 May 2020 20:39:26 +0000 (13:39 -0700)]
Merge tag 'block-5.7-2020-05-29' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Two small fixes:
- Revert a block change that mixed up the return values for non-mq
devices
- NVMe poll race fix"
* tag 'block-5.7-2020-05-29' of git://git.kernel.dk/linux-block:
Revert "block: end bio with BLK_STS_AGAIN in case of non-mq devs and REQ_NOWAIT"
nvme-pci: avoid race between nvme_reap_pending_cqes() and nvme_poll()
Linus Torvalds [Fri, 29 May 2020 20:35:45 +0000 (13:35 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Nothing profound here, just a last set of long standing bug fixes:
- Incorrect error unwind in qib and pvrdma
- User triggerable NULL pointer crash in mlx5 with ODP prefetch
- syzkaller RCU race in uverbs
- Rare double free crash in ipoib"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/ipoib: Fix double free of skb in case of multicast traffic in CM mode
RDMA/core: Fix double destruction of uobject
RDMA/pvrdma: Fix missing pci disable in pvrdma_pci_probe()
RDMA/mlx5: Fix NULL pointer dereference in destroy_prefetch_work
IB/qib: Call kobject_put() when kobject_init_and_add() fails
After the fix at insn 10 because we have 's32_min_value < 0' the following
step 11 now has 'smax_value=U32_MAX' where before we pulled the s32_max_value
bound into the smax_value as seen above in 11 with smax_value=2147483647.
In the original step 14 'smin_value=72057594021150720' this trips the logic
in the verifier function check_reg_sane_offset(),
if (smin >= BPF_MAX_VAR_OFF || smin <= -BPF_MAX_VAR_OFF) {
verbose(env, "value %lld makes %s pointer be out of bounds\n",
smin, reg_type_str[type]);
return false;
}
Specifically, the 'smin <= -BPF_MAX_VAR_OFF' check. But with the fix
at step 14 we have bounds 'smin_value=0' so the above check is not tripped
because BPF_MAX_VAR_OFF=1<<29.
We have a smin_value=0 here because at step 10 the smaller smin_value=0 means
the subtractions at steps 11 and 12 bring the smin_value negative.
Then the shift clears the top bit and smin_value is set to 0. Note we still
have the smax_value in the fixed code so any reads will fail. An alternative
would be to have reg_sane_check() do both smin and smax value tests.
To fix the test we can omit the 'r1 >>=8' at line 13. This will change the
err string, but keeps the intention of the test as suggseted by the title,
"check after truncation of boundary-crossing range". If the verifier logic
changes a different value is likely to be thrown in the error or the error
will no longer be thrown forcing this test to be examined. With this change
we see the new state at step 13.
Giving the expected out of bounds error, "value -4294967168 makes map_value
pointer be out of bounds" However, for unpriv case we see a different error
now because of the mixed signed bounds pointer arithmatic. This seems OK so
I've only added the unpriv_errstr for this. Another optino may have been to
do addition on r1 instead of subtraction but I favor the approach above
slightly.
In real test_verif_scale1 code, "w9 = 0" and "w2 = w9" are in
different basic blocks.
In the above, after "r6 += r2", r6 becomes a scalar, which eventually
caused the memory access error. The correct register state should be
a pkt pointer.
The inprecise register state starts at "w2 = w9".
The 32bit register w9 is 0, in __reg_assign_32_into_64(),
the 64bit reg->smax_value is assigned to be U32_MAX.
The 64bit reg->smin_value is 0 and the 64bit register
itself remains constant based on reg->var_off.
In adjust_ptr_min_max_vals(), the verifier checks for a known constant,
smin_val must be equal to smax_val. Since they are not equal,
the verifier decides r6 is a unknown scalar, which caused later failure.
The llvm10 does not have this issue as it generates different code:
w9 = 0 /* R9_w=inv0 */
r8 = *(u32 *)(r1 + 80) /* __sk_buff->data_end */
r7 = *(u32 *)(r1 + 76) /* __sk_buff->data */
......
r6 = r7 /* R6_w=pkt(id=0,off=0,r=0,imm=0) */
r6 += r9 /* R6_w=pkt(id=0,off=0,r=0,imm=0) */
r3 = r6 /* R3_w=pkt(id=0,off=0,r=0,imm=0) */
r3 += 14 /* R3_w=pkt(id=0,off=14,r=0,imm=0) */
if r3 > r8 goto end
...
To fix the above issue, we can include zero in the test condition for
assigning the s32_max_value and s32_min_value to their 64-bit equivalents
smax_value and smin_value.
Further, fix the condition to avoid doing zero extension bounds checks
when s32_min_value <= 0. This could allow for the case where bounds
32-bit bounds (-1,1) get incorrectly translated to (0,1) 64-bit bounds.
When in-fact the -1 min value needs to force U32_MAX bound.
Linus Torvalds [Fri, 29 May 2020 20:31:01 +0000 (13:31 -0700)]
Merge tag 'sound-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Only a few last-minute small fixes: the change in ALSA core hwdep is
about the undefined behavior of bit shift, which is almost harmless
but still worth to pick up quickly.
The rest are all device-specific fixes for HD-audio and USB-audio, and
safe to apply at the late stage"
* tag 'sound-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Add new codec supported for ALC287
ALSA: usb-audio: Quirks for Gigabyte TRX40 Aorus Master onboard audio
ALSA: usb-audio: mixer: volume quirk for ESS Technology Asus USB DAC
ALSA: hda/realtek - Add a model for Thinkpad T570 without DAC workaround
ALSA: hwdep: fix a left shifting 1 by 31 UB bug
Linus Torvalds [Fri, 29 May 2020 20:29:20 +0000 (13:29 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two fixes for the new SM8150 and SM8250 Qualcomm clk drivers to fix a
randconfig build error and an incorrect parent mapping"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: gcc: Fix parent for gpll0_out_even
clk: qcom: sm8250 gcc depends on QCOM_GDSC
prog->aux->trampoline = tr should be set only when prog is valid.
Otherwise prog freeing will try to put trampoline via prog->aux->trampoline,
but it may not point to a valid trampoline.
net/mlx5e: replace EINVAL in mlx5e_flower_parse_meta()
The drivers reports EINVAL to userspace through netlink on invalid meta
match. This is confusing since EINVAL is usually reserved for malformed
netlink messages. Replace it by more meaningful codes.
Vlad Buslov [Mon, 25 May 2020 13:57:51 +0000 (16:57 +0300)]
net/mlx5e: Fix MLX5_TC_CT dependencies
Change MLX5_TC_CT config dependencies to include MLX5_ESWITCH instead of
MLX5_CORE_EN && NET_SWITCHDEV, which are already required by MLX5_ESWITCH.
Without this change mlx5 fails to compile if user disables MLX5_ESWITCH
without also manually disabling MLX5_TC_CT.
Aya Levin [Mon, 13 Apr 2020 08:31:00 +0000 (11:31 +0300)]
net/mlx5e: Fix arch depending casting issue in FEC
Change type of active_fec to u32 to match the type expected by
mlx5e_get_fec_mode. Copy active_fec and configured_fec values to
unsigned long before preforming bitwise manipulations.
Take the same approach when configuring FEC over 50G link modes: copy
the policy into an unsigned long and only than preform bitwise
operations.
Maor Dickman [Sun, 24 May 2020 06:45:44 +0000 (09:45 +0300)]
net/mlx5e: Remove warning "devices are not on same switch HW"
On tunnel decap rule insertion, the indirect mechanism will attempt to
offload the rule on all uplink representors which will trigger the
"devices are not on same switch HW, can't offload forwarding" message
for the uplink which isn't on the same switch HW as the VF representor.
The above flow is valid and shouldn't cause warning message,
fix by removing the warning and only report this flow using extack.
1) Several fixes for ESP gro/gso in transport and beet mode when
IPv6 extension headers are present. From Xin Long.
2) Fix a wrong comment on XFRMA_OFFLOAD_DEV.
From Antony Antony.
3) Fix sk_destruct callback handling on ESP in TCP encapsulation.
From Sabrina Dubroca.
4) Fix a use after free in xfrm_output_gso when used with vxlan.
From Xin Long.
5) Fix secpath handling of VTI when used wiuth IPCOMP.
From Xin Long.
6) Fix an oops when deleting a x-netns xfrm interface.
From Nicolas Dichtel.
7) Fix a possible warning on policy updates. We had a case where it was
possible to add two policies with the same lookup keys.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* tag 'drm-fixes-2020-05-29-1' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Fix potential integer wraparound resulting in a hang
drm/amd/display: drop cursor position check in atomic test
gpu/drm: Ingenic: Fix opaque pointer casted to wrong type
gpu/drm: ingenic: Fix bogus crtc_atomic_check callback
Modern device tree bindings are supposed to be created as YAML-files
in accordance with dt-schema. This commit replaces two DW SPI legacy
bare text bindings with YAML file. As before the bindings file states
that the corresponding dts node is supposed to be compatible either
with generic DW APB SSI controller or with Microsemi/Amazon/Renesas/Intel
vendors-specific controllers, to have registers, interrupts and clocks
properties. Though in case of Microsemi version of the controller
there must be two registers resources specified. Properties like
clock-names, reg-io-width, cs-gpio, num-cs, DMA and slave device
sub-nodes are optional.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Rob Herring <robh@kernel.org> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: linux-mips@vger.kernel.org Link: https://lore.kernel.org/r/20200529182544.9807-1-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Fri, 29 May 2020 18:31:50 +0000 (21:31 +0300)]
spi: dw: Refactor mid_spi_dma_setup() to separate DMA and IRQ config
It's better to understand what bits are set for DMA and for IRQ handling
in mid_spi_dma_setup() if they are grouped accordingly. Thus,
refactor mid_spi_dma_setup() to separate DMA and IRQ configuration.
Andy Shevchenko [Fri, 29 May 2020 18:31:49 +0000 (21:31 +0300)]
spi: dw: Make DMA request line assignments explicit for Intel Medfield
The ebe375c3e7a9 ("spi: dw: Discard static DW DMA slave structures")
did a clean up of global variables, which is fine, but messed up with
the carefully provided information in the custom DMA slave structures.
There reader can find an assignment of the DMA request lines in use.
Partially revert the above mentioned commit to restore readability
and maintainability of the code.
Mark Brown [Fri, 29 May 2020 17:48:46 +0000 (18:48 +0100)]
spi: bcm2835: Remove shared interrupt support
This reverts commit 04ae75946ef2 since Lukas Wunner noticed that we
start operating on the hardware before we check to see if this is a
spurious interrupt.
Reported-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 29 May 2020 16:49:56 +0000 (17:49 +0100)]
Merge series "spi: dw: Add generic DW DMA controller support" from Serge Semin <Sergey.Semin@baikalelectronics.ru>:
Baikal-T1 SoC provides a DW DMA controller to perform low-speed peripherals
Mem-to-Dev and Dev-to-Mem transaction. This is also applicable to the DW
APB SSI devices embedded into the SoC. Currently the DMA-based transfers
are supported by the DW APB SPI driver only as a middle layer code for
Intel MID/Elkhart PCI devices. Seeing the same code can be used for normal
platform DMAC device we introduced a set of patches to fix it within this
series.
First of all we need to add the Tx and Rx DMA channels support into the DW
APB SSI binding. Then there are several fixes and cleanups provided as a
initial preparation for the Generic DMA support integration: add Tx/Rx
finish wait methods, clear DMAC register when done or stopped, Fix native
CS being unset, enable interrupts in accordance with DMA xfer mode,
discard static DW DMA slave structures, discard unused void priv pointer
and dma_width member of the dw_spi structure, provide the DMA Tx/Rx burst
length parametrisation and make sure it's optionally set in accordance
with the DMA max-burst capability.
In order to have the DW APB SSI MMIO driver working with DMA we need to
initialize the paddr field with the physical base address of the DW APB SSI
registers space. Then we unpin the Intel MID specific code from the
generic DMA one and placed it into the spi-dw-pci.c driver, which is a
better place for it anyway. After that the naming cleanups are performed
since the code is going to be used for a generic DMAC device. Finally the
Generic DMA initialization can be added to the generic version of the
DW APB SSI IP.
Last but not least we traditionally convert the legacy plain text-based
dt-binding file with yaml-based one and as a cherry on a cake replace
the manually written DebugFS registers read method with a ready-to-use
for the same purpose regset32 DebugFS interface usage.
This patchset is rebased and tested on the spi/for-next (5.7-rc5):
base-commit: fe9fce6b2cf3 ("Merge remote-tracking branch 'spi/for-5.8' into spi-next")
Link: https://lore.kernel.org/linux-spi/20200508132943.9826-1-Sergey.Semin@baikalelectronics.ru/
Changelog v2:
- Rebase on top of the spi repository for-next branch.
- Move bindings conversion patch to the tail of the series.
- Move fixes to the head of the series.
- Apply as many changes as possible to be applied the Generic DMA
functionality support is added and the spi-dw-mid is moved to the
spi-dw-dma driver.
- Discard patch "spi: dw: Fix dma_slave_config used partly uninitialized"
since the problem has already been fixed.
- Add new patch "spi: dw: Discard unused void priv pointer".
- Add new patch "spi: dw: Discard dma_width member of the dw_spi structure".
n_bytes member of the DW SPI data can be used instead.
- Build the DMA functionality into the DW APB SSI core if required instead
of creating a separate kernel module.
- Use conditional statement instead of the ternary operator in the ref
clock getter.
Link: https://lore.kernel.org/linux-spi/20200515104758.6934-1-Sergey.Semin@baikalelectronics.ru/
Changelog v3:
- Use spi_delay_exec() method to wait for the DMA operation completion.
- Explicitly initialize the dw_dma_slave members on stack.
- Discard the dws->fifo_len utilization in the Tx FIFO DMA threshold
setting from the patch where we just add the default burst length
constants.
- Use min() method to calculate the optimal burst values.
- Add new patch which moves the spi-dw.c source file to spi-dw-core.c in
order to preserve the DW APB SSI core driver name.
- Add commas in the debugfs_reg32 structure initializer and after the last
entry of the dw_spi_dbgfs_regs array.
Link: https://lore.kernel.org/linux-spi/20200522000806.7381-1-Sergey.Semin@baikalelectronics.ru
Changelog v5:
- Refactor the Tx/Rx DMA-based SPI transfers wait methods.
- Add a new patch "spi: dw: Set xfer effective_speed_hz".
- Add a new patch "spi: dw: Return any value retrieved from the
dma_transfer callback" as a preparation patch before implementing
the local DMA, Tx SPI and Rx SPI transfers wait methods.
- Add a new patch "spi: dw: Locally wait for the DMA transactions
completion", which provides a local DMA transaction complete
method
- Create a dedicated patch which adds the Rx-done wait method:
"spi: dw: Add SPI Rx-done wait method to DMA-based transfer".
- Add more detailed description of the problems the Tx/Rx-wait
methods-related patches fix.
- Wait for the SPI Tx and Rx transfers being finished in the
mid_spi_dma_transfer() method executed in the task context.
- Use spi_delay_exec() to wait for the SPI Tx/Rx completion, since now
the driver calls the wait methods in the kernel thread context.
- Use SPI_DELAY_UNIT_SCK spi_delay unit for Tx-wait delay, since SPI
xfer's are now have the effective_speed_hz initialized.
- Rx-wait for a delay correlated with the APB/SSI synchronous clock
rate instead of using the SPI bus clock rate.
Martin Sperl [Thu, 28 May 2020 18:58:04 +0000 (20:58 +0200)]
spi: bcm2835: Enable shared interrupt support
bcm2711, Rasberry Pi 4's SoC, shares one interrupt for multiple
instances of the bcm2835 SPI controller. So this enables shared
interrupt support for them.
The early bail out in the interrupt routine avoids messing with buffers
of transfers being done by other means. Otherwise, the driver can handle
receiving interrupts asserted by other controllers during an IRQ based
transfer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20200528185805.28991-1-nsaenzjulienne@suse.de Signed-off-by: Mark Brown <broonie@kernel.org>
Fix several issues in the previous gfs2_find_jhead fix:
* When updating @blocks_submitted, @block refers to the first block block not
submitted yet, not the last block submitted, so fix an off-by-one error.
* We want to ensure that @blocks_submitted is far enough ahead of @blocks_read
to guarantee that there is in-flight I/O. Otherwise, we'll eventually end up
waiting for pages that haven't been submitted, yet.
* It's much easier to compare the number of blocks added with the number of
blocks submitted to limit the maximum bio size.
* Even with bio chaining, we can keep adding blocks until we reach the maximum
bio size, as long as we stop at a page boundary. This simplifies the logic.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Reviewed-by: Bob Peterson <rpeterso@redhat.com>
spi: dw: Use regset32 DebugFS method to create regdump file
DebugFS kernel interface provides a dedicated method to create the
registers dump file. Use it instead of creating a generic DebugFS
file with manually written read callback function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-16-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
spi: dw: Add DMA support to the DW SPI MMIO driver
Since the common code in the spi-dw-dma.c driver is ready to be used
by the MMIO driver and now provides a method to generically (on any
DT or ACPI-based platforms) retrieve the Tx/Rx DMA channel handlers,
we can use it and a set of the common DW SPI DMA callbacks to enable
DMA at least for generic "snps,dw-apb-ssi" and "snps,dwc-ssi-1.01a"
devices.
Since from now the former Intel MID platform layer is used as a generic
DW SPI DMA module, let's alter the internal methods naming to be
DMA-related instead of having the "mid_" prefix.
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
Seeing all of the DW SPI driver components like DW SPI DMA/PCI/MMIO
depend on the DW SPI core code it's better to use the if-endif
conditional kernel config statement to signify that common dependency.
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
Since there is a generic method available to initialize the DW SPI DMA
interface on any DT and ACPI-based platforms, which in general can be
designed with not only DW DMAC but with any DMA engine on board, we can
freely remove the CONFIG_DW_DMAC_PCI config from dependency list of
CONFIG_SPI_DW_DMA. Especially seeing that we don't use anything DW DMAC
specific in the new driver.
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
This is a preparation patch before adding the DW DMA support into the
DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the
intended to be generic DW APB SSI DMA code. This isn't that hard,
since the most part of the spi-dw-mid.c driver in fact implements a
generic DMA interface for the DW SPI controller driver. The only Intel
MID specifics concern getting the max frequency from the MRST Clock
Control Unit and fetching the DMA controller channels from
corresponding PCIe DMA controller. Since first one is related with the
SPI interface configuration we moved it' implementation into the
DW PCIe-SPI driver module. After that former spi-dw-mid.c file
can be just renamed to be the DW SPI DMA module optionally compiled in to
the DW APB SSI core driver.
spi: dw: Add core suffix to the DW APB SSI core source file
Generic DMA support is going to be part of the DW APB SSI core object.
In order to preserve the kernel loadable module name as spi-dw.ko, let's
add the "-core" suffix to the object with generic DW APB SSI code and
build it into the target spi-dw.ko driver.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-10-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
Tx-only DMA transfers are working perfectly fine since in this case
the code just ignores the Rx FIFO overflow interrupts. But it turns
out the SPI Rx-only transfers are broken since nothing pushing any
data to the shift registers, so the Rx FIFO is left empty and the
SPI core subsystems just returns a timeout error. Since DW DMAC
driver doesn't support something like cyclic write operations of
a single byte to a device register, the only way to support the
Rx-only SPI transfers is to fake it by using a dummy Tx-buffer.
This is what we intend to fix in this commit by setting the
SPI_CONTROLLER_MUST_TX flag for DMA-capable platform.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-9-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
spi: dw: Use DMA max burst to set the request thresholds
Each channel of DMA controller may have a limited length of burst
transaction (number of IO operations performed at ones in a single
DMA client request). This parameter can be used to setup the most
optimal DMA Tx/Rx data level values. In order to avoid the Tx buffer
overrun we can set the DMA Tx level to be of FIFO depth minus the
maximum burst transactions length. To prevent the Rx buffer underflow
the DMA Rx level should be set to the maximum burst transactions length.
This commit setups the DMA channels and the DW SPI DMA Tx/Rx levels
in accordance with these rules.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-8-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
It isn't good to have numeric literals in the code especially if there
are multiple of them and they are related. Let's replace the Tx and Rx
burst level literals with the corresponding constants.
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
Having any data left in the Rx FIFO after the DMA engine claimed it has
finished all DMA transactions is an abnormal situation, since the DW SPI
controller driver expects to have all the data being fetched and placed
into the SPI Rx buffer at that moment. In case if that has happened we
hopefully assume that the DMA engine may still be doing the data fetching,
thus we give it sometime to finish. If after a short period of time the
data is still left in the Rx FIFO, the driver will give up waiting and
return an error indicating that the SPI controller/DMA engine must have
hung up or failed at some point of doing their duties.
spi: dw: Add SPI Tx-done wait method to DMA-based transfer
Since DMA transfers are performed asynchronously with actual SPI bus
transfers, then even if DMA transactions are finished it doesn't mean
all data is actually pushed to the SPI bus. Some data might still be
in the controller FIFO. This is specifically true for Tx-only transfers.
In this case if the next SPI transfer is recharged while a tail of the
previous one is still in FIFO, we'll loose that tail data. In order to
fix that problem let's add the wait procedure of the Tx SPI transfer
completion after the DMA transactions are finished.
spi: dw: Locally wait for the DMA transfers completion
In general each DMA-based SPI transfer can be split up into two stages:
DMA data transmission/reception and SPI-bus transmission/reception. DMA
asynchronous transactions completion can be tracked by means of the
DMA async Tx-descriptor completion callback. But that callback being
called indicates that the DMA transfer has been finished, it doesn't
mean that SPI data transmission is also done. Moreover in fact it isn't
for at least Tx-only SPI transfers. Upon DMA transfer completion some
data is left in the Tx FIFO and being pushed out by the SPI controller.
So in order to make sure that an SPI transfer is completely pushed to the
SPI-bus, the driver has to wait for both DMA transaction and the SPI-bus
transmission/reception are finished. Note if there is a way to
asynchronously track the former event by means of the DMA async Tx
callback, there isn't easy one for the later (IRQ-based solution won't
work since SPI controller doesn't notify about Rx FIFO being empty).
The DMA transfer completion callback isn't suitable to wait for the
SPI controller activity finish either. The callback might (in case of DW
DMAC it will) be called in the tasklet context. Waiting for the SPI
controller to complete the transfer might take a considerable amount of
time since SPI-bus might be pretty slow. In this case delaying the
execution in the tasklet atomic context might cause significant system
performance drop.
So to speak the best option we've got to solve the problem is to
consequently wait for both stages being finished in the locally
implemented SPI transfer execution procedure even if it costs us of the
local wait-function re-implementation. In this case we don't need to use
the SPI-core transfer-wait functionality, but we'll make sure that
all DMA and SPI-bus transactions are completely finished before the
SPI-core transfer_one callback returns. In this commit we provide an
implementation of the DMA-transfers completion wait functionality.
The DW APB SSI DMA-specific SPI transfer_one function waits for both
Tx and Rx DMA transfers being finished, and only then exits with zero
returned signalling to the SPI core that the SPI transfer is finished.
This implementation is fully equivalent to the currently used
DMA-execution-SPI-core-wait algorithm. The SPI-bus transmission/reception
wait methods will be added in the follow-up commits.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-4-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
spi: dw: Return any value retrieved from the dma_transfer callback
DW APB SSI DMA-part of the driver may need to perform the requested
SPI-transfer synchronously. In that case the dma_transfer() callback
will return 0 as a marker of the SPI transfer being finished so the
SPI core doesn't need to wait and may proceed with the SPI message
trasnfers pumping procedure. This will be needed to fix the problem
when DMA transactions are finished, but there is still data left in
the SPI Tx/Rx FIFOs being sent/received. But for now make dma_transfer
to return 1 as the normal dw_spi_transfer_one() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Feng Tang <feng.tang@intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-3-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
Seeing DW APB SSI controller doesn't support setting the exactly
requested SPI bus frequency, but only a rounded frequency determined
by means of the odd-numbered half-worded reference clock divider,
it would be good to tune the SPI core up and initialize the current
transfer effective_speed_hz. By doing so the core will be able to
execute the xfer-related delays with better accuracy.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Feng Tang <feng.tang@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-mips@vger.kernel.org Cc: devicetree@vger.kernel.org Link: https://lore.kernel.org/r/20200529131205.31838-2-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org>
Helge Deller [Thu, 28 May 2020 20:29:25 +0000 (22:29 +0200)]
parisc: Fix kernel panic in mem_init()
The Debian kernel v5.6 triggers this kernel panic:
Kernel panic - not syncing: Bad Address (null pointer deref?)
Bad Address (null pointer deref?): Code=26 (Data memory access rights trap) at addr 0000000000000000
CPU: 0 PID: 0 Comm: swapper Not tainted 5.6.0-2-parisc64 #1 Debian 5.6.14-1
IAOQ[0]: mem_init+0xb0/0x150
IAOQ[1]: mem_init+0xb4/0x150
RP(r2): start_kernel+0x6c8/0x1190
Backtrace:
[<0000000040101ab4>] start_kernel+0x6c8/0x1190
[<0000000040108574>] start_parisc+0x158/0x1b8
on a HP-PARISC rp3440 machine with this memory layout:
Memory Ranges:
0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB
1) Start 0x0000004040000000 End 0x00000040ffdfffff Size 3070 MB
Fix the crash by avoiding virt_to_page() and similar functions in
mem_init() until the memory zones have been fully set up.
Qiushi Wu [Wed, 27 May 2020 21:00:19 +0000 (16:00 -0500)]
iommu: Fix reference count leak in iommu_group_alloc.
kobject_init_and_add() takes reference even when it fails.
Thus, when kobject_init_and_add() returns an error,
kobject_put() must be called to properly clean up the kobject.
Mark Brown [Fri, 29 May 2020 13:00:44 +0000 (14:00 +0100)]
Merge series "regmap: provide simple bitops and use them in a driver" from Bartosz Golaszewski <brgl@bgdev.pl>
Bartosz Golaszewski <bgolaszewski@baylibre.com>:
I noticed that oftentimes I use regmap_update_bits() for simple bit
setting or clearing. In this case the fourth argument is superfluous as
it's always 0 or equal to the mask argument.
This series proposes to add simple bit operations for setting, clearing
and testing specific bits with regmap.
The second patch uses all three in a driver that got recently picked into
the net-next tree.
The patches obviously target different trees so - if you're ok with
the change itself - I propose you pick the first one into your regmap
tree for v5.8 and then I'll resend the second patch to add the first
user for these macros for v5.9.
v1 -> v2:
- convert the new macros to static inline functions
v2 -> v3:
- drop unneeded ternary operator
Bartosz Golaszewski (2):
regmap: provide helpers for simple bit operations
net: ethernet: mtk-star-emac: use regmap bitops
Mark Brown [Fri, 29 May 2020 13:00:43 +0000 (14:00 +0100)]
Merge series "New DSA driver for VSC9953 Seville switch" from Vladimir Oltean <olteanv@gmail.com>:
Looking at the Felix and Ocelot drivers, Maxim asked if it would be
possible to use them as a base for a new driver for the switch inside
NXP T1040. Turns out, it is! The result is a driver eerily similar to
Felix.
The biggest challenge seems to be getting register read/write API
generic enough to cover such wild bitfield variations between hardware
generations. There is a patch on the regmap core which I would like to
get in through the networking subsystem, if possible (and if Mark is
ok), since it's a trivial addition.
Maxim Kochetkov (4):
soc/mscc: ocelot: add MII registers description
net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
net: mscc: ocelot: extend watermark encoding function
net: dsa: ocelot: introduce driver for Seville VSC9953 switch
Vladimir Oltean (7):
regmap: add helper for per-port regfield initialization
net: mscc: ocelot: unexport ocelot_probe_port
net: mscc: ocelot: convert port registers to regmap
net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to
regfields
net: dsa: ocelot: create a template for the DSA tags on xmit
net: mscc: ocelot: split writes to pause frame enable bit and to
thresholds
net: mscc: ocelot: disable flow control on NPI interface
In many instances regmap_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Vladimir Oltean [Wed, 27 May 2020 23:41:03 +0000 (02:41 +0300)]
regmap: add helper for per-port regfield initialization
Similar to the standalone regfields, add an initializer for the users
who need to set .id_size and .id_offset in order to use the
regmap_fields_update_bits_base API.
Linus Walleij [Wed, 27 May 2020 14:07:58 +0000 (16:07 +0200)]
gpio: fix locking open drain IRQ lines
We provided the right semantics on open drain lines being
by definition output but incidentally the irq set up function
would only allow IRQs on lines that were "not output".
Fix the semantics to allow output open drain lines to be used
for IRQs.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Tested-by: Hans Verkuil <hverkuil@xs4all.nl> Cc: Russell King <linux@armlinux.org.uk> Cc: stable@vger.kernel.org # v5.3+ Link: https://lore.kernel.org/r/20200527140758.162280-1-linus.walleij@linaro.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is caused by __sanitizer_cov_trace_pc() causing an SLB fault
after MSR[RI] has been cleared by __hard_EE_RI_disable(), which we
can not recover from.
Do not instrument the new syscall/interrupt entry/exit code with KCOV,
GCOV or UBSAN.
Reported-by: syzbot-ppc64 <ozlabsyz@au1.ibm.com> Fixes: db7c4451017f ("powerpc/64/sycall: Implement syscall entry/exit logic in C") Signed-off-by: Daniel Axtens <dja@axtens.net> Acked-by: Andrew Donnellan <ajd@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This occurred when sending a v4 skb over vxlan6 over ipsec, in which case
skb->protocol == htons(ETH_P_IPV6) while skb->sk->sk_family == AF_INET in
xfrm_local_error(). Then it will go to xfrm6_local_error() where it tries
to get ipv6 info from a ipv4 sk.
This issue was actually fixed by Commit 0204236dda24 ("xfrm: make local
error reporting more robust"), but brought back by Commit efc527f87570
("xfrm: choose protocol family by skb protocol").
So to fix it, we should call xfrm6_local_error() only when skb->protocol
is htons(ETH_P_IPV6) and skb->sk->sk_family is AF_INET6.
Fixes: efc527f87570 ("xfrm: choose protocol family by skb protocol") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Eric Dumazet [Thu, 28 May 2020 21:57:47 +0000 (14:57 -0700)]
net: be more gentle about silly gso requests coming from user
Recent change in virtio_net_hdr_to_skb() broke some packetdrill tests.
When --mss=XXX option is set, packetdrill always provide gso_type & gso_size
for its inbound packets, regardless of packet size.
if (packet->tcp && packet->mss) {
if (packet->ipv4)
gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV4;
else
gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV6;
gso.gso_size = packet->mss;
}
Since many other programs could do the same, relax virtio_net_hdr_to_skb()
to no longer return an error, but instead ignore gso settings.
This keeps Willem intent to make sure no malicious packet could
reach gso stack.
Note that TCP stack has a special logic in tcp_set_skb_tso_segs()
to clear gso_size for small packets.
Fixes: c6b161d9baf7 ("net: check untrusted gso_size at kernel entry") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jonas Falkevik [Wed, 27 May 2020 09:56:40 +0000 (11:56 +0200)]
sctp: check assoc before SCTP_ADDR_{MADE_PRIM, ADDED} event
Make sure SCTP_ADDR_{MADE_PRIM,ADDED} are sent only for associations
that have been established.
These events are described in rfc6458#section-6.1
SCTP_PEER_ADDR_CHANGE:
This tag indicates that an address that is
part of an existing association has experienced a change of
state (e.g., a failure or return to service of the reachability
of an endpoint via a specific transport address).
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jay Lang [Sun, 24 May 2020 16:27:39 +0000 (12:27 -0400)]
x86/ioperm: Prevent a memory leak when fork fails
In the copy_process() routine called by _do_fork(), failure to allocate
a PID (or further along in the function) will trigger an invocation to
exit_thread(). This is done to clean up from an earlier call to
copy_thread_tls(). Naturally, the child task is passed into exit_thread(),
however during the process, io_bitmap_exit() nullifies the parent's
io_bitmap rather than the child's.
As copy_thread_tls() has been called ahead of the failure, the reference
count on the calling thread's io_bitmap is incremented as we would expect.
However, io_bitmap_exit() doesn't accept any arguments, and thus assumes
it should trash the current thread's io_bitmap reference rather than the
child's. This is pretty sneaky in practice, because in all instances but
this one, exit_thread() is called with respect to the current task and
everything works out.
A determined attacker can issue an appropriate ioctl (i.e. KDENABIO) to
get a bitmap allocated, and force a clone3() syscall to fail by passing
in a zeroed clone_args structure. The kernel handles the erroneous struct
and the buggy code path is followed, and even though the parent's reference
to the io_bitmap is trashed, the child still holds a reference and thus
the structure will never be freed.
Fix this by tweaking io_bitmap_exit() and its subroutines to accept a
task_struct argument which to operate on.
Fixes: 881038260446 ("x86/ioperm: Remove bitmap if all permissions dropped") Signed-off-by: Jay Lang <jaytlang@mit.edu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable#@vger.kernel.org Link: https://lkml.kernel.org/r/20200524162742.253727-1-jaytlang@mit.edu
io_uring does do the right thing for this case, and we're still returning
-EAGAIN to userspace for the cases we don't support. Revert this change
to avoid doing endless spins of resubmits.
fs/binfmt_elf.c: allocate initialized memory in fill_thread_core_info()
KMSAN reported uninitialized data being written to disk when dumping
core. As a result, several kilobytes of kmalloc memory may be written
to the core file and then read by a non-privileged user.
Reported-by: sam <sunhaoyl@outlook.com> Signed-off-by: Alexander Potapenko <glider@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Kees Cook <keescook@chromium.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200419100848.63472-1-glider@google.com Link: https://github.com/google/kmsan/issues/76 Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / kernel.git / log