Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi into master
Pull SCSI fix from James Bottomley:
"One small driver fix. Although the one liner makes it sound like a
cosmetic change, it's a regression fix for the megaraid_sas driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: megaraid_sas: Remove undefined ENABLE_IRQ_POLL macro
Merge tag 'hwmon-for-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging into master
Pull hwmon fixes from Guenter Roeck:
- Using SCT on some Tohsiba drives causes firmware hangs. Disable its
use in the drivetemp driver.
- Handle potential buffer overflows in scmi and aspeed-pwm-tacho
driver.
- Energy reporting does not work well on all AMD CPUs. Restrict
amd_energy to known working models.
- Enable reading the CPU temperature on NCT6798D using undocumented
registers.
- Fix read errors seen if PEC is enabled in adm1275 driver.
- Fix setting the pwm1_enable in emc2103 driver.
* tag 'hwmon-for-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (drivetemp) Avoid SCT usage on Toshiba DT01ACA family drives
hwmon: (scmi) Fix potential buffer overflow in scmi_hwmon_probe()
hwmon: (nct6775) Accept PECI Calibration as temperature source for NCT6798D
hwmon: (adm1275) Make sure we are reading enough data for different chips
hwmon: (emc2103) fix unable to change fan pwm1_enable attribute
hwmon: (amd_energy) match for supported models
hwmon: (aspeed-pwm-tacho) Avoid possible buffer overflow
Merge tag 'riscv-for-linus-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into master
Pull RISC-V fixes from Palmer Dabbelt:
"Two fixes:
- 16KiB kernel stacks on rv64, which fixes a lot of crashes.
- Rolling an mmiowb() into the scheduler, which when combined with
Will's fix to the mmiowb()-on-spinlock should fix the PREEMPT
issues we've been seeing"
* tag 'riscv-for-linus-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Upgrade smp_mb__after_spinlock() to iorw,iorw
riscv: use 16KB kernel stack on 64-bit
Merge tag 'powerpc-5.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux into master
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 5.8:
- A fix to the VAS code we merged this cycle, to report the proper
error code to userspace for address translation failures. And a
selftest update to match.
- Another fix for our pkey handling of PROT_EXEC mappings.
- A fix for a crash when booting a "secure VM" under an ultravisor
with certain numbers of CPUs.
Thanks to: Aneesh Kumar K.V, Haren Myneni, Laurent Dufour, Sandipan
Das, Satheesh Rajendran, Thiago Jung Bauermann"
* tag 'powerpc-5.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc: Use proper error code to check fault address
powerpc/vas: Report proper error code for address translation failure
powerpc/pseries/svm: Fix incorrect check for shared_lppaca_size
powerpc/book3s64/pkeys: Fix pkey_access_permitted() for execute disable pkey
hwmon: (drivetemp) Avoid SCT usage on Toshiba DT01ACA family drives
It has been observed that Toshiba DT01ACA family drives have
WRITE FPDMA QUEUED command timeouts and sometimes just freeze until
power-cycled under heavy write loads when their temperature is getting
polled in SCT mode. The SMART mode seems to be fine, though.
Let's make sure we don't use SCT mode for these drives then.
While only the 3 TB model was actually caught exhibiting the problem let's
play safe here to avoid data corruption and extend the ban to the whole
family.
Merge tag 'nfs-for-5.8-3' of git://git.linux-nfs.org/projects/anna/linux-nfs into master
Pull NFS client fixes from Anna Schumaker:
"A few more NFS client bugfixes for Linux 5.8:
NFS:
- Fix interrupted slots by using the SEQUENCE operation
SUNRPC:
- revert 2f64a3af0d80 to fix unkillable IOs
xprtrdma:
- Fix double-free in rpcrdma_ep_create()
- Fix recursion into rpcrdma_xprt_disconnect()
- Fix return code from rpcrdma_xprt_connect()
- Fix handling of connect errors
- Fix incorrect header size calculations"
* tag 'nfs-for-5.8-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC reverting 2f64a3af0d80 ("NFSv4 fix CLOSE not waiting for direct IO compeletion")
xprtrdma: fix incorrect header size calculations
NFS: Fix interrupted slots by sending a solo SEQUENCE operation
xprtrdma: Fix handling of connect errors
xprtrdma: Fix return code from rpcrdma_xprt_connect()
xprtrdma: Fix recursion into rpcrdma_xprt_disconnect()
xprtrdma: Fix double-free in rpcrdma_ep_create()
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux into master
Pull arm64 fixes from Will Deacon:
"A batch of arm64 fixes.
Although the diffstat is a bit larger than we'd usually have at this
stage, a decent amount of it is the addition of comments describing
our syscall tracing behaviour, and also a sweep across all the modular
arm64 PMU drivers to make them rebust against unloading and unbinding.
There are a couple of minor things kicking around at the moment (CPU
errata and module PLTs for very large modules), but I'm not expecting
any significant changes now for us in 5.8.
- Fix kernel text addresses for relocatable images booting using EFI
and with KASLR disabled so that they match the vmlinux ELF binary.
- Fix unloading and unbinding of PMU driver modules.
- Fix generic mmiowb() when writeX() is called from preemptible
context (reported by the riscv folks).
- Fix ptrace hardware single-step interactions with signal handlers,
system calls and reverse debugging.
- Fix reporting of 64-bit x0 register for 32-bit tasks via
'perf_regs'.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
drivers/perf: Prevent forced unbinding of PMU drivers
asm-generic/mmiowb: Allow mmiowb_set_pending() when preemptible()
arm64: Use test_tsk_thread_flag() for checking TIF_SINGLESTEP
arm64: ptrace: Use NO_SYSCALL instead of -1 in syscall_trace_enter()
arm64: syscall: Expand the comment about ptrace and syscall(-1)
arm64: ptrace: Add a comment describing our syscall entry/exit trap ABI
arm64: compat: Ensure upper 32 bits of x0 are zero on syscall return
arm64: ptrace: Override SPSR.SS when single-stepping is enabled
arm64: ptrace: Consistently use pseudo-singlestep exceptions
drivers/perf: Fix kernel panic when rmmod PMU modules during perf sampling
efi/libstub/arm64: Retain 2MB kernel Image alignment if !KASLR
SUNRPC reverting 2f64a3af0d80 ("NFSv4 fix CLOSE not waiting for direct IO compeletion")
Reverting commit 2f64a3af0d80 "NFSv4 fix CLOSE not waiting for
direct IO compeletion". This patch made it so that fput() by calling
inode_dio_done() in nfs_file_release() would wait uninterruptably
for any outstanding directIO to the file (but that wait on IO should
be killable).
The problem the patch was also trying to address was REMOVE returning
ERR_ACCESS because the file is still opened, is supposed to be resolved
by server returning ERR_FILE_OPEN and not ERR_ACCESS.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Merge tag 'fuse-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse into master
Pull fuse fixes from Miklos Szeredi:
- two regressions in this cycle caused by the conversion of writepage
list to an rb_tree
- two regressions in v5.4 cause by the conversion to the new mount API
- saner behavior of fsconfig(2) for the reconfigure case
- an ancient issue with FS_IOC_{GET,SET}FLAGS ioctls
* tag 'fuse-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: Fix parameter for FS_IOC_{GET,SET}FLAGS
fuse: don't ignore errors from fuse_writepages_fill()
fuse: clean up condition for writepage sending
fuse: reject options on reconfigure via fsconfig(2)
fuse: ignore 'data' argument of mount(..., MS_REMOUNT)
fuse: use ->reconfigure() instead of ->remount_fs()
fuse: fix warning in tree_insert() and clean up writepage insertion
fuse: move rb_erase() before tree_insert()
Merge tag 'ovl-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs into master
Pull overlayfs fixes from Miklos Szeredi:
- fix a regression introduced in v4.20 in handling a regenerated
squashfs lower layer
- two regression fixes for this cycle, one of which is Oops inducing
- miscellaneous issues
* tag 'ovl-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix lookup of indexed hardlinks with metacopy
ovl: fix unneeded call to ovl_change_flags()
ovl: fix mount option checks for nfs_export with no upperdir
ovl: force read-only sb on failure to create index dir
ovl: fix regression with re-formatted lower squashfs
ovl: fix oops in ovl_indexdir_cleanup() with nfs_export=on
ovl: relax WARN_ON() when decoding lower directory file handle
ovl: remove not used argument in ovl_check_origin
ovl: change ovl_copy_up_flags static
ovl: inode reference leak in ovl_is_inuse true case.
Merge tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into master
Pull spi fixes from Mark Brown:
"A couple of small driver specific fixes for fairly minor issues"
* tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-sun6i: sun6i_spi_transfer_one(): fix setting of clock rate
spi: mediatek: use correct SPI_CFG2_REG MACRO
Merge tag 'regulator-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into master
Pull regulator fixes from Mark Brown:
"The more substantial fix here is the rename of the da903x driver which
fixes a collision with the parent MFD driver name which caused issues
when things were built as modules.
There's also a fix for a mislableled regulator on the pmi8994 which is
quite important for systems with that device"
* tag 'regulator-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
MAINTAINERS: remove obsolete entry after file renaming
regulator: rename da903x to da903x-regulator
regulator: qcom_smd: Fix pmi8994 label
Merge tag 'regmap-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into master
Pull regmap fixes from Mark Brown:
"A couple of substantial fixes here, one from Doug which fixes the
debugfs code for MMIO regmaps (fortunately not the common case) and
one from Marc fixing lookups of multiple regmaps for the same device
(a very unusual case).
There's also a fix for Kconfig to ensure we enable SoundWire properly"
* tag 'regmap-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: debugfs: Don't sleep while atomic for fast_io regmaps
regmap: add missing dependency on SoundWire
regmap: dev_get_regmap_match(): fix string comparison
RISC-V: Upgrade smp_mb__after_spinlock() to iorw,iorw
While digging through the recent mmiowb preemption issue it came up that
we aren't actually preventing IO from crossing a scheduling boundary.
While it's a bit ugly to overload smp_mb__after_spinlock() with this
behavior, it's what PowerPC is doing so there's some precedent.
Merge tag 'renesas-fixes-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.8
- Replace CONFIG_PCIE_RCAR by CONFIG_PCIE_RCAR_HOST in the defconfig,
to unblock a planned Kconfig change.
* tag 'renesas-fixes-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST
Merge tag 'sound-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into master
Pull sound fixes from Takashi Iwai:
"No surprise here, just a few device-specific small fixes: two fixes
for USB LINE6 and one for USB-audio drivers wrt syzkaller fuzzer
issues, while the rest are all HD-audio Realtek quirks"
* tag 'sound-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - fixup for yet another Intel reference board
ALSA: hda/realtek - Enable Speaker for ASUS UX563
ALSA: hda/realtek - Enable Speaker for ASUS UX533 and UX534
ALSA: hda/realtek: Enable headset mic of Acer TravelMate B311R-31 with ALC256
ALSA: hda/realtek: enable headset mic of ASUS ROG Zephyrus G14(G401) series with ALC289
ALSA: hda/realtek - change to suitable link model for ASUS platform
ALSA: usb-audio: Fix race against the error recovery URB submission
ALSA: line6: Sync the pending work cancel at disconnection
ALSA: line6: Perform sanity check for each URB creation
Qi Liu [Fri, 17 Jul 2020 08:49:23 +0000 (16:49 +0800)]
drivers/perf: Prevent forced unbinding of PMU drivers
Forcefully unbinding PMU drivers during perf sampling will lead to
a kernel panic, because the perf upper-layer framework call a NULL
pointer in this situation.
To solve this issue, "suppress_bind_attrs" should be set to true, so
that bind/unbind can be disabled via sysfs and prevent unbinding PMU
drivers during perf sampling.
Will Deacon [Thu, 16 Jul 2020 11:28:16 +0000 (12:28 +0100)]
asm-generic/mmiowb: Allow mmiowb_set_pending() when preemptible()
Although mmiowb() is concerned only with serialising MMIO writes occuring
in contexts where a spinlock is held, the call to mmiowb_set_pending()
from the MMIO write accessors can occur in preemptible contexts, such
as during driver probe() functions where ordering between CPUs is not
usually a concern, assuming that the task migration path provides the
necessary ordering guarantees.
Unfortunately, the default implementation of mmiowb_set_pending() is not
preempt-safe, as it makes use of a a per-cpu variable to track its
internal state. This has been reported to generate the following splat
on riscv:
Although it's possible to fix the driver in this case, other splats have
been seen from other drivers, including the infamous 8250 UART, and so
it's better to address this problem in the mmiowb core itself.
Fix mmiowb_set_pending() by using the raw_cpu_ptr() to get at the mmiowb
state and then only updating the 'mmiowb_pending' field if we are not
preemptible (i.e. we have a non-zero nesting count).
Cc: Arnd Bergmann <arnd@arndb.de> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Guo Ren <guoren@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Reported-by: Palmer Dabbelt <palmer@dabbelt.com> Reported-by: Emil Renner Berthing <kernel@esmil.dk> Tested-by: Emil Renner Berthing <kernel@esmil.dk> Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com> Acked-by: Palmer Dabbelt <palmerdabbelt@google.com> Link: https://lore.kernel.org/r/20200716112816.7356-1-will@kernel.org Signed-off-by: Will Deacon <will@kernel.org>
Merge tag 'drm-fixes-2020-07-17-1' of git://anongit.freedesktop.org/drm/drm into master
Pull drm fixes from Dave Airlie:
"Weekly fixes pull, big bigger than I'd normally like, but they are
fairly scattered and small individually.
The vmwgfx one is a black screen regression, otherwise the largest is
an MST encoder fix for amdgpu which results in a WARN in some cases,
and a scattering of i915 fixes.
I'm tracking two regressions at the moment that hopefully we get
nailed down this week for rc7.
dma-buf:
- sleeping atomic fix
amdgpu:
- Fix a race condition with KIQ
- Preemption fix
- Fix handling of fake MST encoders
- OLED panel fix
- Handle allocation failure in stream construction
- Renoir SMC fix
- SDMA 5.x fix
i915:
- FBC w/a stride fix
- Fix use-after-free fix on module reload
- Ignore irq enabling on the virtual engines to fix device sleep
- Use GTT when saving/restoring engine GPR
- Fix selftest sort function
vmwgfx:
- black screen fix
aspeed:
- fbcon init warn fix"
* tag 'drm-fixes-2020-07-17-1' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu/sdma5: fix wptr overwritten in ->get_wptr()
drm/amdgpu/powerplay: Modify SMC message name for setting power profile mode
drm/amd/display: handle failed allocation during stream construction
drm/amd/display: OLED panel backlight adjust not work with external display connected
drm/amdgpu/display: create fake mst encoders ahead of time (v4)
drm/amdgpu: fix preemption unit test
drm/amdgpu/gfx10: fix race condition for kiq
drm/i915: Recalculate FBC w/a stride when needed
drm/i915: Move cec_notifier to intel_hdmi_connector_unregister, v2.
drm/i915/gt: Only swap to a random sibling once upon creation
drm/i915/gt: Ignore irq enabling on the virtual engines
drm/i915/perf: Use GTT when saving/restoring engine GPR
drm/i915/selftests: Fix compare functions provided for sorting
drm/vmwgfx: fix update of display surface when resolution changes
dmabuf: use spinlock to access dmabuf->name
drm/aspeed: Call drm_fbdev_generic_setup after drm_dev_register
Merge tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.8-rc cycle
Few fixes for issues noticed during testing:
- Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module
driver
- A regression fix for ti-sysc no-idle handling that caused issues
compared to earlier platform data based booting
- A fix for memory leak for omap_hwmod_allocate_module
- Fix d_can driver probe for am437x
* tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dcan driver probe failed on am437x platform
ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
bus: ti-sysc: Do not disable on suspend for no-idle
bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
Merge tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.8, round 2:
- A couple of fixes on i.MX platform device registration code to stop
the use of invalid IRQ 0.
- Fix a regression seen on ls1021a platform, caused by commit be2eaea444a7c ("soc: imx: move cpu code to drivers/soc/imx").
- Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.
* tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: check ls1021a
ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
ARM: imx: Provide correct number of resources when registering gpio devices
ARM: dts: imx6qdl-gw551x: fix audio SSI
Douglas Anderson [Wed, 15 Jul 2020 23:46:15 +0000 (16:46 -0700)]
regmap: debugfs: Don't sleep while atomic for fast_io regmaps
If a regmap has "fast_io" set then its lock function uses a spinlock.
That doesn't work so well with the functions:
* regmap_cache_only_write_file()
* regmap_cache_bypass_write_file()
Both of the above functions have the pattern:
1. Lock the regmap.
2. Call:
debugfs_write_file_bool()
copy_from_user()
__might_fault()
__might_sleep()
Let's reorder things a bit so that we do all of our sleepable
functions before we grab the lock.
Merge tag 'pm-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into master
Pull power management fixes from Rafael Wysocki:
"Add missing handling of a command line switch to the intel_pstate
driver (Rafael Wysocki) and fix the freeing of the operating
performance point (OPP) entries for the legacy (v1) OPP table type
(Walter Lozano)"
* tag 'pm-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
opp: Increase parsed_static_opps in _of_add_opp_table_v1()
cpufreq: intel_pstate: Fix active mode setting from command line
Merge tag 'char-misc-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into master
Pull char/misc fixes from Greg KH:
"Here are number of small char/misc driver fixes for 5.8-rc6
Not that many complex fixes here, just a number of small fixes for
reported issues, and some new device ids. Nothing fancy.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (21 commits)
virtio: virtio_console: add missing MODULE_DEVICE_TABLE() for rproc serial
intel_th: Fix a NULL dereference when hub driver is not loaded
intel_th: pci: Add Emmitsburg PCH support
intel_th: pci: Add Tiger Lake PCH-H support
intel_th: pci: Add Jasper Lake CPU support
virt: vbox: Fix guest capabilities mask check
virt: vbox: Fix VBGL_IOCTL_VMMDEV_REQUEST_BIG and _LOG req numbers to match upstream
uio_pdrv_genirq: fix use without device tree and no interrupt
uio_pdrv_genirq: Remove warning when irq is not specified
coresight: etmv4: Fix CPU power management setup in probe() function
coresight: cti: Fix error handling in probe
Revert "zram: convert remaining CLASS_ATTR() to CLASS_ATTR_RO()"
mei: bus: don't clean driver pointer
misc: atmel-ssc: lock with mutex instead of spinlock
phy: sun4i-usb: fix dereference of pointer phy0 before it is null checked
phy: rockchip: Fix return value of inno_dsidphy_probe()
phy: ti: j721e-wiz: Constify structs
phy: ti: am654-serdes: Constify regmap_config
phy: intel: fix enum type mismatch warning
phy: intel: Fix compilation error on FIELD_PREP usage
...
Merge tag 'driver-core-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core into master
Pull driver core fixes from Greg KH:
"Here are 3 driver core fixes for 5.8-rc6.
They resolve some issues found with the deferred probe code for some
types of devices on some embedded systems. They have been tested a
bunch and have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Avoid deferred probe due to fw_devlink_pause/resume()
driver core: Rename dev_links_info.defer_sync to defer_hook
driver core: Don't do deferred probe in parallel with kernel_init thread
Merge tag 'staging-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging into master
Pull IIO and staging driver fixes from Greg KH:
"Here are some IIO and staging driver fixes for 5.8-rc6.
The majority of fixes are for IIO drivers, resolving a number of small
reported issues, and there are some counter fixes in here too that
were tied to the IIO fixes. There's only one staging driver fix here,
a comedi fix found by code inspection.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: verify array index is correct before using it
iio: adc: ad7780: Fix a resource handling path in 'ad7780_probe()'
iio:pressure:ms5611 Fix buffer element alignment
iio:humidity:hts221 Fix alignment and data leak issues
iio:humidity:hdc100x Fix alignment and data leak issues
iio:magnetometer:ak8974: Fix alignment and data leak issues
iio: adc: adi-axi-adc: Fix object reference counting
iio: pressure: zpa2326: handle pm_runtime_get_sync failure
counter: 104-quad-8: Add lock guards - filter clock prescaler
counter: 104-quad-8: Add lock guards - differential encoder
iio: core: add missing IIO_MOD_H2/ETHANOL string identifiers
iio: magnetometer: ak8974: Fix runtime PM imbalance on error
iio: mma8452: Add missed iio_device_unregister() call in mma8452_probe()
iio:health:afe4404 Fix timestamp alignment and prevent data leak.
iio:health:afe4403 Fix timestamp alignment and prevent data leak.
Merge tag 'tty-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty into master
Pull tty/serial driver fixes from Greg KH:
:Here are some small tty and serial driver fixes for 5.8-rc6.
The largest set of patches in here is a revert of the sysrq changes
that went into 5.8-rc1 but turned out to cause a noticable overhead
and cpu usage.
Other than that, there's a few small serial driver fixes to resolve
reported issues, and finally resolving the spinlock init problem on
many serial driver consoles.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: core: Initialise spin lock before use in uart_configure_port()
serial: mxs-auart: add missed iounmap() in probe failure and remove
serial: sh-sci: Initialize spinlock for uart console
Revert "tty: xilinx_uartps: Fix missing id assignment to the console"
serial: core: drop redundant sysrq checks
serial: core: fix sysrq overhead regression
Revert "serial: core: Refactor uart_unlock_and_check_sysrq()"
tty/serial: fix serial_core.c kernel-doc warnings
tty: serial: cpm_uart: Fix behaviour for non existing GPIOs
Merge tag 'thermal-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux into master
Pull thermal fixes from Daniel Lezcano:
- Fix invalid index array access on int340x_thermal leading to a kernel
panic (Bartosz Szczepanek)
- Fix debug message level to prevent flooding on some platform (Alex
Hung)
- Fix invalid bank access by reverting "thermal: mediatek: fix register
index error" (Enric Balletbo i Serra)
* tag 'thermal-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
Revert "thermal: mediatek: fix register index error"
thermal: int3403_thermal: Downgrade error message
thermal/int340x_thermal: Prevent page fault on .set_mode() op
nvme: explicitly update mpath disk capacity on revalidation
Commit 9201b11c160717 ("nvme: fix possible deadlock when I/O is
blocked") reverted multipath head disk revalidation due to deadlocks
caused by holding the bd_mutex during revalidate.
Updating the multipath disk blockdev size is still required though for
userspace to be able to observe any resizing while the device is
mounted. Directly update the bdev inode size to avoid unnecessarily
holding the bdev->bd_mutex.
Fixes: 9201b11c160717 ("nvme: fix possible deadlock when I/O is
blocked")
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Will Deacon [Fri, 3 Jul 2020 08:41:24 +0000 (09:41 +0100)]
arm64: syscall: Expand the comment about ptrace and syscall(-1)
If a task executes syscall(-1), we intercept this early and force x0 to
be -ENOSYS so that we don't need to distinguish this scenario from one
where the scno is -1 because a tracer wants to skip the system call
using ptrace. With the return value set, the return path is the same as
the skip case.
Although there is a one-line comment noting this in el0_svc_common(), it
misses out most of the detail. Expand the comment to describe a bit more
about what is going on.
Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Cc: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org>
Will Deacon [Thu, 2 Jul 2020 20:14:20 +0000 (21:14 +0100)]
arm64: ptrace: Add a comment describing our syscall entry/exit trap ABI
Our tracehook logic for syscall entry/exit raises a SIGTRAP back to the
tracer following a ptrace request such as PTRACE_SYSCALL. As part of this
procedure, we clobber the reported value of one of the tracee's general
purpose registers (x7 for native tasks, r12 for compat) to indicate
whether the stop occurred on syscall entry or exit. This is a slightly
unfortunate ABI, as it prevents the tracer from accessing the real
register value and is at odds with other similar stops such as seccomp
traps.
Since we're stuck with this ABI, expand the comment in our tracehook
logic to acknowledge the issue and describe the behaviour in more detail.
Cc: Mark Rutland <mark.rutland@arm.com> Cc: Luis Machado <luis.machado@linaro.org> Reported-by: Keno Fischer <keno@juliacomputing.com> Signed-off-by: Will Deacon <will@kernel.org>
Will Deacon [Fri, 3 Jul 2020 11:08:42 +0000 (12:08 +0100)]
arm64: compat: Ensure upper 32 bits of x0 are zero on syscall return
Although we zero the upper bits of x0 on entry to the kernel from an
AArch32 task, we do not clear them on the exception return path and can
therefore expose 64-bit sign extended syscall return values to userspace
via interfaces such as the 'perf_regs' ABI, which deal exclusively with
64-bit registers.
Explicitly clear the upper 32 bits of x0 on return from a compat system
call.
Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Cc: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org>
Will Deacon [Thu, 13 Feb 2020 12:06:26 +0000 (12:06 +0000)]
arm64: ptrace: Override SPSR.SS when single-stepping is enabled
Luis reports that, when reverse debugging with GDB, single-step does not
function as expected on arm64:
| I've noticed, under very specific conditions, that a PTRACE_SINGLESTEP
| request by GDB won't execute the underlying instruction. As a consequence,
| the PC doesn't move, but we return a SIGTRAP just like we would for a
| regular successful PTRACE_SINGLESTEP request.
The underlying problem is that when the CPU register state is restored
as part of a reverse step, the SPSR.SS bit is cleared and so the hardware
single-step state can transition to the "active-pending" state, causing
an unexpected step exception to be taken immediately if a step operation
is attempted.
In hindsight, we probably shouldn't have exposed SPSR.SS in the pstate
accessible by the GPR regset, but it's a bit late for that now. Instead,
simply prevent userspace from configuring the bit to a value which is
inconsistent with the TIF_SINGLESTEP state for the task being traced.
Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Keno Fischer <keno@juliacomputing.com> Link: https://lore.kernel.org/r/1eed6d69-d53d-9657-1fc9-c089be07f98c@linaro.org Reported-by: Luis Machado <luis.machado@linaro.org> Tested-by: Luis Machado <luis.machado@linaro.org> Signed-off-by: Will Deacon <will@kernel.org>
Will Deacon [Thu, 2 Jul 2020 20:16:20 +0000 (21:16 +0100)]
arm64: ptrace: Consistently use pseudo-singlestep exceptions
Although the arm64 single-step state machine can be fast-forwarded in
cases where we wish to generate a SIGTRAP without actually executing an
instruction, this has two major limitations outside of simply skipping
an instruction due to emulation.
1. Stepping out of a ptrace signal stop into a signal handler where
SIGTRAP is blocked. Fast-forwarding the stepping state machine in
this case will result in a forced SIGTRAP, with the handler reset to
SIG_DFL.
2. The hardware implicitly fast-forwards the state machine when executing
an SVC instruction for issuing a system call. This can interact badly
with subsequent ptrace stops signalled during the execution of the
system call (e.g. SYSCALL_EXIT or seccomp traps), as they may corrupt
the stepping state by updating the PSTATE for the tracee.
Resolve both of these issues by injecting a pseudo-singlestep exception
on entry to a signal handler and also on return to userspace following a
system call.
Cc: <stable@vger.kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Tested-by: Luis Machado <luis.machado@linaro.org> Reported-by: Keno Fischer <keno@juliacomputing.com> Signed-off-by: Will Deacon <will@kernel.org>
To solve the above issue, current module should be registered to kernel,
so that try_module_get() can be invoked when perf sampling starts. This
adds the reference counting of module and could prevent users from removing
modules during sampling.
Amir Goldstein [Wed, 15 Jul 2020 13:38:08 +0000 (16:38 +0300)]
ovl: fix lookup of indexed hardlinks with metacopy
We recently moved setting inode flag OVL_UPPERDATA to ovl_lookup().
When looking up an overlay dentry, upperdentry may be found by index
and not by name. In that case, we fail to read the metacopy xattr
and falsly set the OVL_UPPERDATA on the overlay inode.
This caused a regression in xfstest overlay/033 when run with
OVERLAY_MOUNT_OPTIONS="-o metacopy=on".
Fixes: c836583bd656 ("ovl: initialize OVL_UPPERDATA in ovl_lookup()") Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Walter Lozano [Thu, 16 Jul 2020 02:54:52 +0000 (23:54 -0300)]
opp: Increase parsed_static_opps in _of_add_opp_table_v1()
Currently, when using _of_add_opp_table_v2 parsed_static_opps is
increased and this value is used in _opp_remove_all_static() to
check if there are static opp entries that need to be freed.
Unfortunately this does not happen when using _of_add_opp_table_v1(),
which leads to warnings.
This patch increases parsed_static_opps in _of_add_opp_table_v1() in a
similar way as in _of_add_opp_table_v2().
Fixes: 026b83225fcb ("opp: Replace list_kref with a local counter") Cc: v5.6+ <stable@vger.kernel.org> # v5.6+ Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
[ Viresh: Do the operation with lock held and set the value to 1 instead
of incrementing it ] Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux into master
Pull clk fixes from Stephen Boyd:
"A couple build fixes for issues exposed this merge window and a fix
for the eMMC clk on AST2600 SoCs that fixes the rate that is
calculated by the clk framework"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Specify IOMEM dependency for HSDK pll driver
clk: AST2600: Add mux for EMMC clock
clk: mvebu: ARMADA_AP_CPU_CLK needs to select ARMADA_AP_CP_HELPER
Dave Airlie [Thu, 16 Jul 2020 00:10:15 +0000 (10:10 +1000)]
Merge tag 'drm-intel-fixes-2020-07-15' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.8-rc6:
- FBC w/a stride fix
- Fix use-after-free fix on module reload
- Ignore irq enabling on the virtual engines to fix device sleep
- Use GTT when saving/restoring engine GPR
- Fix selftest sort function
Dave Airlie [Thu, 16 Jul 2020 00:09:55 +0000 (10:09 +1000)]
Merge tag 'drm-misc-fixes-2020-07-15' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
* aspeed: setup fbdev console after registering device; avoids warning
and stacktrace in dmesg log
* dmabuf: protect dmabuf->name with a spinlock; avoids sleeping in
atomic context
Merge tag 'platform-drivers-x86-v5.8-2' of git://git.infradead.org/linux-platform-drivers-x86 into master
Pull x86 platform driver fixes from Andriy Shevchenko:
"Small fixes for this cycle:
- Fix procfs handling in Thinkpad ACPI driver
- Fix battery management on new ASUS laptops
- New IDs (Sapphire Rapids) in ISST tool"
* tag 'platform-drivers-x86-v5.8-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: asus-wmi: allow BAT1 battery name
platform/x86: ISST: Add new PCI device ids
platform/x86: thinkpad_acpi: Revert "Use strndup_user() in dispatch_proc_write()"
David Howells [Wed, 8 Jul 2020 08:27:07 +0000 (09:27 +0100)]
afs: Fix interruption of operations
The afs filesystem driver allows unstarted operations to be cancelled by
signal, but most of these can easily be restarted (mkdir for example). The
primary culprits for reproducing this are those applications that use
SIGALRM to display a progress counter.
File lock-extension operation is marked uninterruptible as we have a
limited time in which to do it, and the release op is marked
uninterruptible also as if we fail to unlock a file, we'll have to wait 20
mins before anyone can lock it again.
The store operation logs a warning if it gets interruption, e.g.:
kAFS: Unexpected error from FS.StoreData -4
because it's run from the background - but it can also be run from
fdatasync()-type things. However, store options aren't marked
interruptible at the moment.
Fix this in the following ways:
(1) Mark store operations as uninterruptible. It might make sense to
relax this for certain situations, but I'm not sure how to make sure
that background store ops aren't affected by signals to foreground
processes that happen to trigger them.
(2) In afs_get_io_locks(), where we're getting the serialisation lock for
talking to the fileserver, return ERESTARTSYS rather than EINTR
because a lot of the operations (e.g. mkdir) are restartable if we
haven't yet started sending the op to the server.
Fixes: 511b1ded7178 ("afs: Build an abstraction around an "operation" concept") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Amir Goldstein [Mon, 13 Jul 2020 14:19:44 +0000 (17:19 +0300)]
ovl: fix mount option checks for nfs_export with no upperdir
Without upperdir mount option, there is no index dir and the dependency
checks nfs_export => index for mount options parsing are incorrect.
Allow the combination nfs_export=on,index=off with no upperdir and move
the check for dependency redirect_dir=nofollow for non-upper mount case
to mount options parsing.
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Mon, 13 Jul 2020 14:19:43 +0000 (17:19 +0300)]
ovl: force read-only sb on failure to create index dir
With index feature enabled, on failure to create index dir, overlay is
being mounted read-only. However, we do not forbid user to remount overlay
read-write. Fix that by setting ofs->workdir to NULL, which prevents
remount read-write.
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Wed, 8 Jul 2020 13:16:13 +0000 (16:16 +0300)]
ovl: fix regression with re-formatted lower squashfs
Commit 571e3d8206bc ("ovl: relax requirement for non null uuid of lower
fs") relaxed the requirement for non null uuid with single lower layer to
allow enabling index and nfs_export features with single lower squashfs.
Fabian reported a regression in a setup when overlay re-uses an existing
upper layer and re-formats the lower squashfs image. Because squashfs
has no uuid, the origin xattr in upper layer are decoded from the new
lower layer where they may resolve to a wrong origin file and user may
get an ESTALE or EIO error on lookup.
To avoid the reported regression while still allowing the new features
with single lower squashfs, do not allow decoding origin with lower null
uuid unless user opted-in to one of the new features that require
following the lower inode of non-dir upper (index, xino, metacopy).
Reported-by: Fabian <godi.beat@gmx.net> Link: https://lore.kernel.org/linux-unionfs/32532923.JtPX5UtSzP@fgdesktop/ Fixes: 571e3d8206bc ("ovl: relax requirement for non null uuid of lower fs") Cc: stable@vger.kernel.org # v4.20+ Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Bisect point at commit f67e4645f4e1 ("ovl: whiteout inode sharing")
Minimal reproducer:
--------------------------------------------------
rm -rf l u w m
mkdir -p l u w m
mkdir -p l/testdir
touch l/testdir/testfile
mount -t overlay -o lowerdir=l,upperdir=u,workdir=w,nfs_export=on overlay m
echo 1 > m/testdir/testfile
umount m
rm -rf u/testdir
mount -t overlay -o lowerdir=l,upperdir=u,workdir=w,nfs_export=on overlay m
umount m
--------------------------------------------------
When mount with nfs_export=on, and fail to verify an orphan index, we're
cleaning this index from indexdir by calling ovl_cleanup_and_whiteout().
This dereferences ofs->workdir, that was earlier set to NULL.
The design was that ovl->workdir will point at ovl->indexdir, but we are
assigning ofs->indexdir to ofs->workdir only after ovl_indexdir_cleanup().
There is no reason not to do it sooner, because once we get success from
ofs->indexdir = ovl_workdir_create(... there is no turning back.
Amir Goldstein [Wed, 17 Jun 2020 06:57:11 +0000 (09:57 +0300)]
ovl: relax WARN_ON() when decoding lower directory file handle
Decoding a lower directory file handle to overlay path with cold
inode/dentry cache may go as follows:
1. Decode real lower file handle to lower dir path
2. Check if lower dir is indexed (was copied up)
3. If indexed, get the upper dir path from index
4. Lookup upper dir path in overlay
5. If overlay path found, verify that overlay lower is the lower dir
from step 1
On failure to verify step 5 above, user will get an ESTALE error and a
WARN_ON will be printed.
A mismatch in step 5 could be a result of lower directory that was renamed
while overlay was offline, after that lower directory has been copied up
and indexed.
This is a scripted reproducer based on xfstest overlay/052:
# Create lower subdir
create_dirs
create_test_files $lower/lowertestdir/subdir
mount_dirs
# Copy up lower dir and encode lower subdir file handle
touch $SCRATCH_MNT/lowertestdir
test_file_handles $SCRATCH_MNT/lowertestdir/subdir -p -o $tmp.fhandle
# Rename lower dir offline
unmount_dirs
mv $lower/lowertestdir $lower/lowertestdir.new/
mount_dirs
# Attempt to decode lower subdir file handle
test_file_handles $SCRATCH_MNT -p -i $tmp.fhandle
Since this WARN_ON() can be triggered by user we need to relax it.
Fixes: f4828b2f596f ("ovl: lookup connected ancestor of dir in inode cache") Cc: <stable@vger.kernel.org> # v4.16+ Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
As the ENABLE_IRQ_POLL macro is undefined, the check for ENABLE_IRQ_POLL
macro in ISR will always be false. This leads to irq polling being
non-functional.
Remove ENABLE_IRQ_POLL check from ISR.
Link: https://lore.kernel.org/r/20200715120153.20512-1-chandrakanth.patil@broadcom.com Fixes: 16c9eed26780 ("scsi: megaraid_sas: Call disable_irq from process IRQ") Cc: <stable@vger.kernel.org> # v5.3+ Signed-off-by: Chandrakanth Patil <chandrakanth.patil@broadcom.com> Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Wed, 15 Jul 2020 16:26:04 +0000 (17:26 +0100)]
xprtrdma: fix incorrect header size calculations
Currently the header size calculations are using an assignment
operator instead of a += operator when accumulating the header
size leading to incorrect sizes. Fix this by using the correct
operator.
Addresses-Coverity: ("Unused value") Fixes: f0713f461aaf ("xprtrdma: Prevent inline overflow") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Haren Myneni [Fri, 10 Jul 2020 23:49:58 +0000 (16:49 -0700)]
selftests/powerpc: Use proper error code to check fault address
ERR_NX_TRANSLATION(CSB.CC=5) is for internal to VAS for fault handling
and should not used by OS. ERR_NX_AT_FAULT(CSB.CC=250) is the proper
error code should be reported by OS when NX encounters address
translation failure.
This patch uses CC=250 to determine the fault address when the request
is not successful.
Haren Myneni [Fri, 10 Jul 2020 23:47:19 +0000 (16:47 -0700)]
powerpc/vas: Report proper error code for address translation failure
P9 DD2 NX workbook (Table 4-36) says DMA controller uses CC=5
internally for translation fault handling. NX reserves CC=250 for
OS to notify user space when NX encounters address translation
failure on the request buffer. Not an issue in earlier releases
as NX does not get faults on kernel addresses.
This patch defines CSB_CC_FAULT_ADDRESS(250) and updates CSB.CC with
this proper error code for user space.
The ioctl encoding for this parameter is a long but the documentation says
it should be an int and the kernel drivers expect it to be an int. If the
fuse driver treats this as a long it might end up scribbling over the stack
of a userspace process that only allocated enough space for an int.
This was previously discussed in [1] and a patch for fuse was proposed in
[2]. From what I can tell the patch in [2] was nacked in favor of adding
new, "fixed" ioctls and using those from userspace. However there is still
no "fixed" version of these ioctls and the fact is that it's sometimes
infeasible to change all userspace to use the new one.
Handling the ioctls specially in the fuse driver seems like the most
pragmatic way for fuse servers to support them without causing crashes in
userspace applications that call them.
This broke procfs interface due to neglecting the fact that
the strings are not coming NULL terminated.
Revert the change till we will have a better clean up.
Fixes: 852931eb8f21 ("platform/x86: thinkpad_acpi: Use strndup_user() in dispatch_proc_write()") Reported-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The above patch is supposed to fix a register index error on mt2701. It
is not clear if the problem solved is a hang or just an invalid value
returned, my guess is the second. The patch introduces, though, a new
hang on MT8173 device making them unusable. So, seems reasonable, revert
the patch because introduces a worst issue.
The reason I send a revert instead of trying to fix the issue for MT8173
is because the information needed to fix the issue is in the datasheet
and is not public. So I am not really able to fix it.
Fixes the following bug when CONFIG_MTK_THERMAL is set on MT8173
devices.
hwmon: (nct6775) Accept PECI Calibration as temperature source for NCT6798D
Stefan Dietrich reports invalid temperature source messages on Asus Formula
XII Z490.
nct6775 nct6775.656: Invalid temperature source 28 at index 0,
source register 0x100, temp register 0x73
Debugging suggests that temperature source 28 reports the CPU temperature.
Let's assume that temperature sources 28 and 29 reflect "PECI Agent {0,1}
Calibration", similar to other chips of the series.
Reported-by: Stefan Dietrich <roots@gmx.de> Cc: Stefan Dietrich <roots@gmx.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Andreas Schwab [Mon, 6 Jul 2020 12:32:26 +0000 (14:32 +0200)]
riscv: use 16KB kernel stack on 64-bit
With the current 8KB stack size there are frequent overflows in a 64-bit
configuration. We may split IRQ stacks off in the future, but this fixes a
number of issues right now.
Signed-off-by: Andreas Schwab <schwab@suse.de> Reviewed-by: Anup Patel <anup@brainfault.org>
[Palmer: mention irqstack in the commit text] Fixes: 3387f28a7b55 ("RISC-V: Task implementation") Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
drm/amdgpu/sdma5: fix wptr overwritten in ->get_wptr()
"u64 *wptr" points to the the wptr value in write back buffer and
"*wptr = (*wptr) >> 2;" results in the value being overwritten each time
when ->get_wptr() is called.
umr uses /sys/kernel/debug/dri/0/amdgpu_ring_sdma0 to get rptr/wptr and
decode ring content and it is affected by this issue.
fix and simplify the logic similar as sdma_v4_0_ring_get_wptr().
v2: fix for sdma5.2 as well
v3: drop sdma 5.2 changes for 5.8 and stable
Suggested-by: Le Ma <le.ma@amd.com> Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
chen gong [Mon, 13 Jul 2020 08:11:24 +0000 (16:11 +0800)]
drm/amdgpu/powerplay: Modify SMC message name for setting power profile mode
I consulted Cai Land(Chuntian.Cai@amd.com), he told me corresponding smc
message name to fSMC_MSG_SetWorkloadMask() is
"PPSMC_MSG_ActiveProcessNotify" in firmware code of Renoir.
Strange though it may seem, but it's a fact.
Signed-off-by: chen gong <curry.gong@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
hersen wu [Mon, 22 Jun 2020 17:29:16 +0000 (13:29 -0400)]
drm/amd/display: OLED panel backlight adjust not work with external display connected
[Why]
amdgpu_dm->backlight_caps is for single eDP only. the caps are upddated
for very connector. Real eDP caps will be overwritten by other external
display. For OLED panel, caps->aux_support is set to 1 for OLED pnael.
after external connected, caps+.aux_support is set to 0. This causes
OLED backlight adjustment not work.
[How]
within update_conector_ext_caps, backlight caps will be updated only for
eDP connector.
Cc: stable@vger.kernel.org Signed-off-by: hersen wu <hersenxs.wu@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jack Xiao [Fri, 10 Jul 2020 04:18:22 +0000 (12:18 +0800)]
drm/amdgpu/gfx10: fix race condition for kiq
During preemption test for gfx10, it uses kiq to trigger
gfx preemption, which would result in race condition
with flushing TLB for kiq.
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ville Syrjälä [Sat, 11 Jul 2020 08:03:36 +0000 (11:03 +0300)]
drm/i915: Recalculate FBC w/a stride when needed
Currently we're failing to recalculate the gen9 FBC w/a stride
unless something more drastic than just the modifier itself has
changed. This often leaves us with FBC enabled with the linear
fbdev framebuffer without the w/a stride enabled. That will cause
an immediate underrun and FBC will get promptly disabled.
Fix the problem by checking if the w/a stride is about to change,
and go through the full dance if so. This part of the FBC code
is still pretty much a disaster and will need lots more work.
But this should at least fix the immediate issue.
v2: Deactivate FBC when the modifier changes since that will
likely require resetting the w/a CFB stride
drm/i915: Move cec_notifier to intel_hdmi_connector_unregister, v2.
This fixes the following KASAN splash on module reload:
[ 145.136327] ==================================================================
[ 145.136502] BUG: KASAN: use-after-free in intel_hdmi_destroy+0x74/0x80 [i915]
[ 145.136514] Read of size 8 at addr ffff888216641830 by task kworker/1:1/134
Chris Wilson [Mon, 13 Jul 2020 16:05:49 +0000 (17:05 +0100)]
drm/i915/gt: Only swap to a random sibling once upon creation
The danger in switching at random upon intel_context_pin is that the
context may still actually be inflight, as it will not be scheduled out
until a context switch after it is complete -- that may be a long time
after we do a final intel_context_unpin.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2118 Fixes: 2f2ab31764ee ("drm/i915: Load balancing across a virtual engine") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: <stable@vger.kernel.org> # v5.3+ Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200713160549.17344-1-chris@chris-wilson.co.uk
(cherry picked from commit 90a987205c6cf74116a102ed446d22d92cdaf915) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Sat, 11 Jul 2020 20:32:36 +0000 (21:32 +0100)]
drm/i915/gt: Ignore irq enabling on the virtual engines
We do not use the virtual engines for interrupts (they have physical
components), but we do use them to decouple the fence signaling during
submission. Currently, when we submit a completed request, we try to
enable the interrupt handler for the virtual engine, but we never disarm
it. A quick fix is then to mark the irq as enabled, and it will then
remain enabled -- and this prevents us from waking the device and never
letting it sleep again.
Fixes: 688c94189b1b ("drm/i915: Initialise breadcrumb lists on the virtual engine") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: <stable@vger.kernel.org> # v5.5+ Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200711203236.12330-1-chris@chris-wilson.co.uk
(cherry picked from commit 4fe6abb8f51355224808ab02a9febf65d184c40b) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm/i915/perf: Use GTT when saving/restoring engine GPR
MI_STORE_REGISTER_MEM and MI_LOAD_REGISTER_MEM need to know which
translation to use when saving restoring the engine general purpose
registers to and from the GT scratch. Since GT scratch is mapped to
ggtt, we need to set an additional bit in the command to use GTT.
Fixes: acff1cc92e482a ("drm/i915/perf: implement active wait for noa configurations") Suggested-by: Prathap Kumar Valsan <prathap.kumar.valsan@intel.com> Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com> Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20200709224504.11345-1-chris@chris-wilson.co.uk Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit e43ff99c8deda85234e6233e0f4af6cb09566a37) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
projects / kernel.git / log