Marek Vasut [Thu, 2 Mar 2023 22:40:44 +0000 (23:40 +0100)]
ARM: dts: imx: Add support for DH electronics i.MX8M Plus DHCOM on PDK3
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK3 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
misc: imx: remove DM dependency for ocotp driver in SPL
The ocotp driver is available for regular and SPL builds using the
(SPL_)MXC_OCOTP configuration. Also, the ocotp driver does not support
the driver model (DM) configuration.
But, for SPL builds, the SPL_MXC_OCOTP configuration depends on
SPL_MISC which implies on SPL_DM.
This commit replaces the dependency on SPL_MISC with SPL_DRIVERS_MISC.
So the only requirement is to have enabled miscellaneous drivers for
the SPL.
Signed-off-by: Jean-Marie Lemetayer <j.lemetayer@kerlink.fr>
The i.MX8MP DHCOM SoM may come with either external RGMII PHY or
LAN8740Ai RMII PHY on the SoM attached to FEC MAC. Add pin mux
settings for both options, so that DT overlay can override these
settings on SoM variant with the LAN8740Ai PHY.
The i.MX8MP DHCOM SoM may come with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY on the SoM attached to EQoS MAC. Add pin
mux settings for both options, so that DT overlay can override
these settings on SoM variant with the LAN8740Ai PHY.
Marek Vasut [Sat, 11 Feb 2023 22:10:50 +0000 (23:10 +0100)]
arm64: imx8mp: Auto-detect PHY on i.MX8MP DHCOM
The i.MX8MP DHCOM SoM may be populated with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY attached to EQoS MAC, and either external RGMII PHY
or LAN8740Ai RMII PHY attached to FEC MAC. The SoM configuration can be
detected for each MAC by reading RX_CTL pull resistor state early on boot.
Make use of this, detect the exact PHY configuration, and patch control DT
accordingly so that the ethernet is configured correctly in U-Boot.
Marek Vasut [Sat, 11 Feb 2023 21:49:01 +0000 (22:49 +0100)]
ARM: imx: Add 2 GiB DRAM support for DH electronics i.MX8M Plus DHCOM
The DH electronics i.MX8M Plus DHCOM SoM currently supports only 4 GiB
of DRAM population option. Add another population option with 2 GiB of
DRAM. The chips used on the 2 GiB option are 2x K4F6E3S4HM-MGCJ .
configs: colibri-imx7: Fix bad block table in flash configuration
Make sure that the bad block table in flash is used on Colibri iMX7.
Without this configuration enabled U-Boot corrupts the bad block table
and Linux will update the table on each reboot. The corruption occurs
because if CONFIG_SYS_NAND_USE_FLASH_BBT is not set, U-boot will store
bad blocks out of band, while the Linux driver for the iMX7 will store
them in band in a bad block table.
Fixes: e0af4a568aa ("arm: dts: imx7: colibri: add raw NAND support") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Ye Li [Fri, 3 Feb 2023 10:24:36 +0000 (18:24 +0800)]
power: pmic: Add NXP PCA9451A PMIC support
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but
has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver
and add new type for PCA9451A.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Marek Vasut <marex@denx.de>
Fabio Estevam [Wed, 15 Feb 2023 18:24:44 +0000 (15:24 -0300)]
pico-imx6: Pass the mmc alias to fix boot regression
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit c2092e38fd66 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: c2092e38fd66 ("imx6dl/imx6qdl: synchronise device trees with linux") Signed-off-by: Fabio Estevam <festevam@denx.de>
Ye Li [Tue, 31 Jan 2023 08:42:34 +0000 (16:42 +0800)]
imx8ulp_evk: Clear data at fdt_addr_r before booting kernel
When using dual boot mode, the DDR won't be reset when APD power off
or reboot. It has possibility that obsolete fdt data existing on
fdt_addr_r address. Then even nothing in EFI partitions, the distro boot
still continue to parse fdt and get uboot crashed.
Clear the data at fdt_addr_r, so the fdt header check in above case
will not pass.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 31 Jan 2023 08:42:33 +0000 (16:42 +0800)]
imx8ulp_evk: disable overflow of port0 for LPAV
Bit0: Port 0 behavior when bandwidth maximized. Set to 1 to allow overflow
With overflow set, we see some issue that A35 may not able to get enough
bandwidth and A35 will report hrtimer takes too much time, workqueue
lockup. With overflow cleared, the issues are gone.
Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:32 +0000 (16:42 +0800)]
imx8ulp_evk: Update DDR ports arbitration for DCNANO underrun
To resolve DCNANO underrun issue, change the DDR Port 0 arbitration
from round robin fashion to fixed priority level 1, while other ports
are not assigned any priority, so they will be serviced in round robin
fashion if there is no active request from Port 0.
Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:28 +0000 (16:42 +0800)]
misc: fuse: Lock 8ULP ECC-protected fuse when programming
The ECC fuse on 8ULP can't be written twice. If any user did it, the
ECC value would be wrong then cause accessing problem to the fuse.
The patch will lock the ECC fuse word to avoid this problem.
For iMX9, the OTP controller automatically prevents an ECC fuse word to
be written twice. So it does not need the setting.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:27 +0000 (16:42 +0800)]
misc: fuse: Update fuse mapping for 8ULP S400 API
Since new 8ULP A1 S400 FW (v0.0.8-e329b760) can support to read
more fuses: like PMU trim, Test flow/USB, GP1-5, GP8-10. Update
the u-boot driver for the new mapping.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Alice Guo <alice.guo@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:26 +0000 (16:42 +0800)]
imx: sentinel: Update S400 API get info message structure
From Sentinel FW v0.0.9-9df0f503, the response message of get info API
is changed to add OEM SRK and some states (IMEM, CSAL, TRNG).
With old structure, we get failure from sentinel due to the buffer
size can't fit with new response message. So update the API structure
to fix the issue.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:24 +0000 (16:42 +0800)]
imx: imx8ulp: Configure XRDC PDAC and MSC for DBD owner=S400 only
This patch is used to support DBD owner fuse changed to S400 only.
The XRDC PDAC2 for LPAV pbridge5 and MSC1/2/3 for GPIO and LPAV are not
configured by S400 default setting. So these PDAC and MSC are invalid,
only DBD owner can access the corresponding resources.
We have to configure necessary PDAC and MSC for SPL before DDR
initialization.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Tue, 31 Jan 2023 08:42:22 +0000 (16:42 +0800)]
imx: imx8ulp: upower: replace magic number with macro
The swton indicates the logic switch, magic number 0xfff80 is hard
to understand, so use macro.
Some board design may not have MIPI_CSI voltage input connected per
data sheet. In that case, the upower power on API may dead loop mu to wait
response, however there is no response. So remove MIPI_CSI here, let
linux power domain driver to runtime enable the power domain.
Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:21 +0000 (16:42 +0800)]
imx: imx8ulp: Clear dividers in PLL3DIV_PFD registers
At present, in cgc1_pll3_init we don't set the pll3pfd div values,
just use the default 0. But on A1 part, ROM will set PLL3 pfd1div2
to 1 and pfd2div1 to 3.
This finally causes some clocks' rate decreased, for example USDHC.
So clear the PLL3DIV_PFD dividers to get correct rate.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:20 +0000 (16:42 +0800)]
imx: imx8ulp: Reconfigure MRC3 for SRAM0 access
Some space in SRAM0 will be protected by S400 to allow RX SecPriv mode
access only for boot purpose. Since SW will reuse the SRAM0 as SCMI
buffer and SPL container loading buffer, need to reconfigure MRC3.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:19 +0000 (16:42 +0800)]
ddr: imx8ulp: Change DRAM timing save area to 0x20055000
To align with ARM trusted firmware's change, adjust DRAM timing
save area to new position 0x20055000. So we can release the space
since 0x2006c000 for the NOBITS region of ARM trusted firmware
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:17 +0000 (16:42 +0800)]
imx: imx8ulp: Adjust handshake to sync TRDC and XRDC completion
To fit the DBD_EN fused part, we re-design the TRDC and XRDC assignment.
M33 will be the TRDC owner and needs to configure TRDC. A35 is the
XRDC owner, ATF will configure XRDC.
The handshake between U-boot and M33 image is used to sync TRDC and
XRDC configuration completion. Once the handshake is done, A35 and M33
can access the allowed resources in others domain.
The handshake is needed when M33 is booted or DBD_EN fused, because both
cases will enable the TRDC. If handshake is timeout, the boot will hang.
We use SIM GPR0 to pass the info from SPL to u-boot, because before the
handshake, u-boot can't access SEC SIM and FSB.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:16 +0000 (16:42 +0800)]
imx: imx8ulp: Remove the TRDC configure from A35
As M33 is responsible for TRDC configuration, the settings for A35
nonsecure world access and DMA0 access are moved to M33 image.
So remove the codes to release TRDC and configure it. Just keep
the configurations for reference.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:13 +0000 (16:42 +0800)]
imx: imx8ulp: Get chip revision from Sentinel
In both SPL and u-boot, after probing the S400 MU, get the chip revision,
lifecycle and UID from Sentinel.
Update get_cpu_rev to use the chip revision not hard coded it for A0
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 31 Jan 2023 08:42:12 +0000 (16:42 +0800)]
imx: imx8ulp: Fix MU device probe failure
Since latest DTS has added multiple MU nodes, using compatible
string to find the device node is not proper. It finds the first
node with the compatible string matched even the node is disabled.
Tom Rini [Mon, 27 Mar 2023 15:16:51 +0000 (11:16 -0400)]
Merge branch '2023-03-27-rockchip-rk3399-fixes'
- A series of minor cleanups to DISTRO_DEFAULTS and BOOTSTD so that the
rk3399 bootstd migration can be complete and functional now, and make
future migrations easier.
Tom Rini [Fri, 24 Mar 2023 20:58:15 +0000 (16:58 -0400)]
rockchip: Use BOOTSTD_DEFAULTS if not DISTRO_DEFAULTS
When we do not enable DISTRO_DEFAULTS (generally, to get distro_bootcmd)
we instea do want to imply BOOTSTD_DEFAULTS so that when using bootstd
the general distro boot functionality will still work.
Simon Glass [Fri, 24 Mar 2023 20:58:13 +0000 (16:58 -0400)]
boot: Create a common BOOT_DEFAULTS for distro and bootstd
These two features use a lot of common options. Move them into a common
CONFIG to reduce duplication.
Use 'select' for most options since these are things that boards aren't
supposed to override. For now it is not possible to disable
BOOT_DEFAULTS but we may take another look later.
Note that five options use 'imply' to match existing behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Rework a bit so we don't grow so many platforms unintentionally] Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Fri, 24 Mar 2023 20:58:10 +0000 (16:58 -0400)]
rockchip: Drop bootstage stash in TPL and SPL for rockpro64
Unfortunately the IRAM used to stash the bootstage records in TPL
becomes inaccessible after SPL runs. Presumably this is because of ATF
taking it over.
We could move the stash to another address in SPL, before passing it to
U-Boot proper. But it seems easier to wait until we have support for
standard passage[1] which should not be too far away.
Sergiu Moga [Wed, 8 Mar 2023 14:39:53 +0000 (16:39 +0200)]
clk: at91: sam9x60: Add initial setup of UPLL and USBCK rates
In order for some of the functionalities, such as the USB clocks,
to work properly we need some clocks to be properly initialised
at the very beginning of booting.
Claudiu Beznea [Wed, 8 Mar 2023 14:39:52 +0000 (16:39 +0200)]
clk: at91: pmc: export clock setup to pmc
Clock setup was intended for setting clocks at boot time on SAMA7G5,
e.g. for root clocks like PLLs, that were used to feed IPs needed alive
in u-boot (e.g. Ethernet clock feed by a PLL). Export this functionality
to all at91 clocks as it may be necessary on other SoCs.
Sergiu Moga [Wed, 8 Mar 2023 14:39:50 +0000 (16:39 +0200)]
clk: at91: Add support for sam9x60 USB clock
Implement sam9x60 USB clock driver. This clock has
three parents: PLLA, UPLL and MAINXTAL. The driver is
aware of the three possible parents with the help of the
two mux tables provied to the driver during the registration
of the clock.
* Let EFI app call ExitBootServices() before legacy booting kernel
* Support zboot and bootm in the EFI app
* Let efi command show configuration tables
* Support booting a 64-bit kernel from 64-bit EFI app
* Allocate device-tree copy from high memory
* simplify efi_str_to_u16()
cmd: bootefi: allocate device-tree copy from high memory
The bootefi command creates a copy of the device-tree within the first
127 MiB of memory. This may lead to overwriting previously loaded binaries
(e.g. kernel, initrd).
Linux EFI stub itself copies U-Boot's copy of the device-tree. This means
there is not restriction for U-Boot to place the device-tree copy to any
address. (Restrictions existed for 32bit ARM before Linux commit 7a1be318f579 ("ARM: 9012/1: move device tree mapping out of linear region")
for legacy booting.
Simon Glass [Sun, 19 Mar 2023 19:30:15 +0000 (08:30 +1300)]
efi: Support showing tables
Add a command (for the app and payload) to display the tables provided
by EFI. Note that for the payload the tables should always be present, so
an error message is unnecessary and would bloat the code.
Simon Glass [Sun, 19 Mar 2023 19:30:12 +0000 (08:30 +1300)]
efi: Include GUID names with EFI app and payload
These are currently only available when running with EFI_LOADER.
Expand this to include the app and payload, since it is useful to be
able to decode things there.
Simon Glass [Sun, 19 Mar 2023 19:30:05 +0000 (08:30 +1300)]
efi: Set RUN_64BIT correctly for the EFI app
The U-Boot EFI app can run as a 64-bit program, so set the Kconfig
correctly in that case. Make sure it doesn't build SPL, since there is
no need to switch from 32 to 64 bit when running.
projects / uboot.git / log