Dave Airlie [Fri, 23 Jul 2021 01:31:50 +0000 (11:31 +1000)]
Merge tag 'drm-misc-next-2021-07-22' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15-rc1:
UAPI Changes:
- Remove sysfs stats for dma-buf attachments, as it causes a performance regression.
Previous merge is not in a rc kernel yet, so no userspace regression possible.
Cross-subsystem Changes:
- Sanitize user input in kyro's viewport ioctl.
- Use refcount_t in fb_info->count
- Assorted fixes to dma-buf.
- Extend x86 efifb handling to all archs.
- Fix neofb divide by 0.
- Document corpro,gm7123 bridge dt bindings.
Core Changes:
- Slightly rework drm master handling.
- Cleanup vgaarb handling.
- Assorted fixes.
Driver Changes:
- Add support for ws2401 panel.
- Assorted fixes to stm, ast, bochs.
- Demidlayer ingenic irq.
Zheyu Ma [Wed, 21 Jul 2021 12:43:44 +0000 (12:43 +0000)]
video: fbdev: neofb: add a check against divide error
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of 'pixclock',
it may cause divide error because of the 'PICOS2KHZ' macro.
Fix this by checking whether 'pixclock' is zero first.
drivers/firmware: consolidate EFI framebuffer setup for all arches
The register_gop_device() function registers an "efi-framebuffer" platform
device to match against the efifb driver, to have an early framebuffer for
EFI platforms.
But there is already support to do exactly the same by the Generic System
Framebuffers (sysfb) driver. This used to be only for X86 but it has been
moved to drivers/firmware and could be reused by other architectures.
Also, besides supporting registering an "efi-framebuffer", this driver can
register a "simple-framebuffer" allowing to use the siple{fb,drm} drivers
on non-X86 EFI platforms. For example, on aarch64 these drivers can only
be used with DT and doesn't have code to register a "simple-frambuffer"
platform device when booting with EFI.
For these reasons, let's remove the register_gop_device() duplicated code
and instead move the platform specific logic that's there to sysfb driver.
drivers/firmware: move x86 Generic System Framebuffers support
The x86 architecture has generic support to register a system framebuffer
platform device. It either registers a "simple-framebuffer" if the config
option CONFIG_X86_SYSFB is enabled, or a legacy VGA/VBE/EFI FB device.
But the code is generic enough to be reused by other architectures and can
be moved out of the arch/x86 directory.
This will allow to also support the simple{fb,drm} drivers on non-x86 EFI
platforms, such as aarch64 where these drivers are only supported with DT.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Acked-by: Borislav Petkov <bp@suse.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20210625130947.1803678-2-javierm@redhat.com
Dave Airlie [Wed, 21 Jul 2021 01:58:26 +0000 (11:58 +1000)]
Merge tag 'drm-misc-next-2021-07-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Fri 16 Jul 2021 21:06:04 AEST
# gpg: using RSA key B97BD6A80CAC4981091AE547FE558C72A67013C3
# gpg: Good signature from "Maarten Lankhorst <maarten.lankhorst@linux.intel.com>" [expired]
# gpg: aka "Maarten Lankhorst <maarten@debian.org>" [expired]
# gpg: aka "Maarten Lankhorst <maarten.lankhorst@canonical.com>" [expired]
# gpg: Note: This key has expired!
# Primary key fingerprint: B97B D6A8 0CAC 4981 091A E547 FE55 8C72 A670 13C3
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/444811c3-cbec-e9d5-9a6b-9632eda7962a@linux.intel.com
The V3D engine has several hardware performance counters that can of
interest for userspace performance analysis tools.
This exposes new ioctls to create and destroy performance monitor
objects, as well as to query the counter values.
Each created performance monitor object has an ID that can be attached
to CL/CSD submissions, so the driver enables the requested counters when
the job is submitted, and updates the performance monitor values when
the job is done.
It is up to the user to ensure all the jobs have been finished before
getting the performance monitor values. It is also up to the user to
properly synchronize BCL jobs when submitting jobs with different
performance monitors attached.
Cc: Daniel Vetter <daniel@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Emma Anholt <emma@anholt.net>
To: dri-devel@lists.freedesktop.org Signed-off-by: Juan A. Suarez Romero <jasuarez@igalia.com> Acked-by: Melissa Wen <mwen@igalia.com> Signed-off-by: Melissa Wen <melissa.srw@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210608111541.461991-1-jasuarez@igalia.com
drm_file->master pointers should be protected by
drm_device.master_mutex or drm_file.master_lookup_lock when being
dereferenced.
However, in drm_lease.c, there are multiple instances where
drm_file->master is accessed and dereferenced while neither lock is
held. This makes drm_lease.c vulnerable to use-after-free bugs.
We address this issue in 2 ways:
1. Add a new drm_file_get_master() function that calls drm_master_get
on drm_file->master while holding on to
drm_file.master_lookup_lock. Since drm_master_get increments the
reference count of master, this prevents master from being freed until
we unreference it with drm_master_put.
2. In each case where drm_file->master is directly accessed and
eventually dereferenced in drm_lease.c, we wrap the access in a call
to the new drm_file_get_master function, then unreference the master
pointer once we are done using it.
drm: serialize drm_file.master with a new spinlock
Currently, drm_file.master pointers should be protected by
drm_device.master_mutex when being dereferenced. This is because
drm_file.master is not invariant for the lifetime of drm_file. If
drm_file is not the creator of master, then drm_file.is_master is
false, and a call to drm_setmaster_ioctl will invoke
drm_new_set_master, which then allocates a new master for drm_file and
puts the old master.
Thus, without holding drm_device.master_mutex, the old value of
drm_file.master could be freed while it is being used by another
concurrent process.
However, it is not always possible to lock drm_device.master_mutex to
dereference drm_file.master. Through the fbdev emulation code, this
might occur in a deep nest of other locks. But drm_device.master_mutex
is also the outermost lock in the nesting hierarchy, so this leads to
potential deadlocks.
To address this, we introduce a new spin lock at the bottom of the
lock hierarchy that only serializes drm_file.master. With this change,
the value of drm_file.master changes only when both
drm_device.master_mutex and drm_file.master_lookup_lock are
held. Hence, any process holding either of those locks can ensure that
the value of drm_file.master will not change concurrently.
Since no lock depends on the new drm_file.master_lookup_lock, when
drm_file.master is dereferenced, but drm_device.master_mutex cannot be
held, we can safely protect the master pointer with
drm_file.master_lookup_lock.
drm: add a locked version of drm_is_current_master
While checking the master status of the DRM file in
drm_is_current_master(), the device's master mutex should be
held. Without the mutex, the pointer fpriv->master may be freed
concurrently by another process calling drm_setmaster_ioctl(). This
could lead to use-after-free errors when the pointer is subsequently
dereferenced in drm_lease_owner().
The callers of drm_is_current_master() from drm_auth.c hold the
device's master mutex, but external callers do not. Hence, we implement
drm_is_current_master_locked() to be used within drm_auth.c, and
modify drm_is_current_master() to grab the device's master mutex
before checking the master status.
drm: avoid blocking in drm_clients_info's rcu section
Inside drm_clients_info, the rcu_read_lock is held to lock
pid_task()->comm. However, within this protected section, a call to
drm_is_current_master is made, which involves a mutex lock in a future
patch. However, this is illegal because the mutex lock might block
while in the RCU read-side critical section.
Since drm_is_current_master isn't protected by rcu_read_lock, we avoid
this by moving it out of the RCU critical section.
The following report came from intel-gfx ci's
igt@debugfs_test@read_all_entries testcase:
=============================
[ BUG: Invalid wait context ]
5.13.0-CI-Patchwork_20515+ #1 Tainted: G W
-----------------------------
debugfs_test/1101 is trying to lock: ffff888132d901a8 (&dev->master_mutex){+.+.}-{3:3}, at:
drm_is_current_master+0x1e/0x50
other info that might help us debug this:
context-{4:4}
3 locks held by debugfs_test/1101:
#0: ffff88810fdffc90 (&p->lock){+.+.}-{3:3}, at:
seq_read_iter+0x53/0x3b0
#1: ffff888132d90240 (&dev->filelist_mutex){+.+.}-{3:3}, at:
drm_clients_info+0x63/0x2a0
#2: ffffffff82734220 (rcu_read_lock){....}-{1:2}, at:
drm_clients_info+0x1b1/0x2a0
stack backtrace:
CPU: 8 PID: 1101 Comm: debugfs_test Tainted: G W
5.13.0-CI-Patchwork_20515+ #1
Hardware name: Intel Corporation CometLake Client Platform/CometLake S
UDIMM (ERB/CRB), BIOS CMLSFWR1.R00.1263.D00.1906260926 06/26/2019
Call Trace:
dump_stack+0x7f/0xad
__lock_acquire.cold.78+0x2af/0x2ca
lock_acquire+0xd3/0x300
? drm_is_current_master+0x1e/0x50
? __mutex_lock+0x76/0x970
? lockdep_hardirqs_on+0xbf/0x130
__mutex_lock+0xab/0x970
? drm_is_current_master+0x1e/0x50
? drm_is_current_master+0x1e/0x50
? drm_is_current_master+0x1e/0x50
drm_is_current_master+0x1e/0x50
drm_clients_info+0x107/0x2a0
seq_read_iter+0x178/0x3b0
seq_read+0x104/0x150
full_proxy_read+0x4e/0x80
vfs_read+0xa5/0x1b0
ksys_read+0x5a/0xd0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
drm: avoid circular locks in drm_mode_getconnector
In preparation for a future patch to take a lock on
drm_device.master_mutex inside drm_is_current_master(), we first move
the call to drm_is_current_master() in drm_mode_getconnector out from the
section locked by &dev->mode_config.mutex. This avoids creating a
circular lock dependency.
Failing to avoid this lock dependency produces the following lockdep
splat:
======================================================
WARNING: possible circular locking dependency detected
5.13.0-rc7-CI-CI_DRM_10254+ #1 Not tainted
------------------------------------------------------
kms_frontbuffer/1087 is trying to acquire lock: ffff88810dcd01a8 (&dev->master_mutex){+.+.}-{3:3}, at: drm_is_current_master+0x1b/0x40
but task is already holding lock: ffff88810dcd0488 (&dev->mode_config.mutex){+.+.}-{3:3}, at: drm_mode_getconnector+0x1c6/0x4a0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&dev->mode_config.mutex){+.+.}-{3:3}:
__mutex_lock+0xab/0x970
drm_client_modeset_probe+0x22e/0xca0
__drm_fb_helper_initial_config_and_unlock+0x42/0x540
intel_fbdev_initial_config+0xf/0x20 [i915]
async_run_entry_fn+0x28/0x130
process_one_work+0x26d/0x5c0
worker_thread+0x37/0x380
kthread+0x144/0x170
ret_from_fork+0x1f/0x30
-> #1 (&client->modeset_mutex){+.+.}-{3:3}:
__mutex_lock+0xab/0x970
drm_client_modeset_commit_locked+0x1c/0x180
drm_client_modeset_commit+0x1c/0x40
__drm_fb_helper_restore_fbdev_mode_unlocked+0x88/0xb0
drm_fb_helper_set_par+0x34/0x40
intel_fbdev_set_par+0x11/0x40 [i915]
fbcon_init+0x270/0x4f0
visual_init+0xc6/0x130
do_bind_con_driver+0x1e5/0x2d0
do_take_over_console+0x10e/0x180
do_fbcon_takeover+0x53/0xb0
register_framebuffer+0x22d/0x310
__drm_fb_helper_initial_config_and_unlock+0x36c/0x540
intel_fbdev_initial_config+0xf/0x20 [i915]
async_run_entry_fn+0x28/0x130
process_one_work+0x26d/0x5c0
worker_thread+0x37/0x380
kthread+0x144/0x170
ret_from_fork+0x1f/0x30
-> #0 (&dev->master_mutex){+.+.}-{3:3}:
__lock_acquire+0x151e/0x2590
lock_acquire+0xd1/0x3d0
__mutex_lock+0xab/0x970
drm_is_current_master+0x1b/0x40
drm_mode_getconnector+0x37e/0x4a0
drm_ioctl_kernel+0xa8/0xf0
drm_ioctl+0x1e8/0x390
__x64_sys_ioctl+0x6a/0xa0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
other info that might help us debug this:
Chain exists of: &dev->master_mutex --> &client->modeset_mutex --> &dev->mode_config.mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->mode_config.mutex);
lock(&client->modeset_mutex);
lock(&dev->mode_config.mutex);
lock(&dev->master_mutex);
*** DEADLOCK ***
1 lock held by kms_frontbuffer/1087:
#0: ffff88810dcd0488 (&dev->mode_config.mutex){+.+.}-{3:3}, at: drm_mode_getconnector+0x1c6/0x4a0
stack backtrace:
CPU: 7 PID: 1087 Comm: kms_frontbuffer Not tainted 5.13.0-rc7-CI-CI_DRM_10254+ #1
Hardware name: Intel Corporation Ice Lake Client Platform/IceLake U DDR4 SODIMM PD RVP TLC, BIOS ICLSFWR1.R00.3234.A01.1906141750 06/14/2019
Call Trace:
dump_stack+0x7f/0xad
check_noncircular+0x12e/0x150
__lock_acquire+0x151e/0x2590
lock_acquire+0xd1/0x3d0
__mutex_lock+0xab/0x970
drm_is_current_master+0x1b/0x40
drm_mode_getconnector+0x37e/0x4a0
drm_ioctl_kernel+0xa8/0xf0
drm_ioctl+0x1e8/0x390
__x64_sys_ioctl+0x6a/0xa0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x44/0xae
V1:
When AST2500 acts as stand-alone VGA so that DRAM and DVO initialization
have to be achieved by VGA driver with P2A (PCI to AHB) enabling.
However, HW suggests disable Fast reset mode after DRAM initializaton,
because fast reset mode is mainly designed for ARM ICE debugger.
Once Fast reset is checked as enabling, WDT (Watch Dog Timer) should be
first enabled to avoid system deadlock before disable fast reset mode.
V2:
Use to_pci_dev() to get revision of PCI configuration.
V3:
If SCU00 is not unlocked, just enter its password again.
It is unnecessary to clear AHB lock condition and restore WDT default
setting again, before Fast-reset clearing.
V4:
repatch after "error : could not build fake ancestor" resolved.
V5:
Since CVE_2019_6260 item3, Most of AST2500 have disabled P2A(PCIe to AMBA).
However, for backward compatibility, some patches about P2A, such as items
of v5.2 and v5.3, are considered to be upstreamed with comments.
1. Add define macro to improve source readability.
ast_drv.h, ast_main.c, ast_post.c
2. Add comment about "Fast restet" is enabled for ARM-ICE debugger
ast_post.c
3. Add comment about Reset USB port to patch USB unknown device issue
ast_post.c
dma-buf: Delete the DMA-BUF attachment sysfs statistics
The DMA-BUF attachment statistics form a subset of the DMA-BUF
sysfs statistics that recently merged to the drm-misc tree. They are not
UABI yet since they have not merged to the upstream Linux kernel.
Since there has been a reported a performance regression due to the
overhead of sysfs directory creation/teardown during
dma_buf_attach()/dma_buf_detach(), this patch deletes the DMA-BUF
attachment statistics from sysfs.
Fixes: bdb8d06dfefd ("dmabuf: Add the capability to expose DMA-BUF stats in sysfs") Signed-off-by: Hridya Valsaraju <hridya@google.com> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://patchwork.freedesktop.org/patch/msgid/20210713040742.2680135-1-hridya@google.com Signed-off-by: Christian König <christian.koenig@amd.com>
Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.
This patch also fixes a bug where the driver didn't release the
IRQ.
v2:
* automatically release IRQ via devm_request_irq() (Paul)
* mention the bugfix (Sam)
Antonio Borneo [Tue, 13 Jul 2021 14:49:41 +0000 (16:49 +0200)]
drm/stm: dsi: compute the transition time from LP to HS and back
The driver uses a conservative set of hardcoded values for the
maximum time delay of the transitions between LP and HS, either
for data and clock lanes.
By using the info in STM32MP157 datasheet, valid also for other ST
devices, compute the actual delay from the lane's bps.
Jagan Teki [Sun, 4 Jul 2021 13:59:14 +0000 (19:29 +0530)]
drm/stm: ltdc: Silence -EPROBE_DEFER till bridge attached
As dw-mipi-dsi supported all possible ways to find the DSI
devices. It can take multiple iterations for ltdc to find
all components attached to the DSI bridge.
The current ltdc driver failed to find the endpoint as
it returned -EINVAL for the first iteration itself. This leads
to following error:
Merge tag 'perf-tools-fixes-for-v5.14-2021-07-18' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Skip invalid hybrid PMU on hybrid systems when the atom (little) CPUs
are offlined.
- Fix 'perf test' problems related to the recently added hybrid
(BIG/little) code.
- Split ARM's coresight (hw tracing) decode by aux records to avoid
fatal decoding errors.
- Fix add event failure in 'perf probe' when running 32-bit perf in a
64-bit kernel.
- Fix 'perf sched record' failure when CONFIG_SCHEDSTATS is not set.
- Fix memory and refcount leaks detected by ASAn when running 'perf
test', should be clean of warnings now.
- Remove broken definition of __LITTLE_ENDIAN from tools'
linux/kconfig.h, which was breaking the build in some systems.
- Cast PTHREAD_STACK_MIN to int as it may turn into 'long
sysconf(__SC_THREAD_STACK_MIN_VALUE), breaking the build in some
systems.
- Fix libperf build error with LIBPFM4=1.
- Sync UAPI files changed by the memfd_secret new syscall.
* tag 'perf-tools-fixes-for-v5.14-2021-07-18' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (35 commits)
perf sched: Fix record failure when CONFIG_SCHEDSTATS is not set
perf probe: Fix add event failure when running 32-bit perf in a 64-bit kernel
perf data: Close all files in close_dir()
perf probe-file: Delete namelist in del_events() on the error path
perf test bpf: Free obj_buf
perf trace: Free strings in trace__parse_events_option()
perf trace: Free syscall tp fields in evsel->priv
perf trace: Free syscall->arg_fmt
perf trace: Free malloc'd trace fields on exit
perf lzma: Close lzma stream on exit
perf script: Fix memory 'threads' and 'cpus' leaks on exit
perf script: Release zstd data
perf session: Cleanup trace_event
perf inject: Close inject.output on exit
perf report: Free generated help strings for sort option
perf env: Fix memory leak of cpu_pmu_caps
perf test maps__merge_in: Fix memory leak of maps
perf dso: Fix memory leak in dso__new_map()
perf test event_update: Fix memory leak of unit
perf test event_update: Fix memory leak of evlist
...
Merge tag 'xfs-5.14-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"A few fixes for issues in the new online shrink code, additional
corrections for my recent bug-hunt w.r.t. extent size hints on
realtime, and improved input checking of the GROWFSRT ioctl.
IOW, the usual 'I somehow got bored during the merge window and
resumed auditing the farther reaches of xfs':
- Fix shrink eligibility checking when sparse inode clusters enabled
- Reset '..' directory entries when unlinking directories to prevent
verifier errors if fs is shrinked later
- Don't report unusable extent size hints to FSGETXATTR
- Don't warn when extent size hints are unusable because the sysadmin
configured them that way
- Fix insufficient parameter validation in GROWFSRT ioctl
- Fix integer overflow when adding rt volumes to filesystem"
* tag 'xfs-5.14-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: detect misaligned rtinherit directory extent size hints
xfs: fix an integer overflow error in xfs_growfs_rt
xfs: improve FSGROWFSRT precondition checking
xfs: don't expose misaligned extszinherit hints to userspace
xfs: correct the narrative around misaligned rtinherit/extszinherit dirs
xfs: reset child dir '..' entry when unlinking child
xfs: check for sparse inode clusters that cross new EOAG when shrinking
Merge tag 'iomap-5.14-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull iomap fixes from Darrick Wong:
"A handful of bugfixes for the iomap code.
There's nothing especially exciting here, just fixes for UBSAN (not
KASAN as I erroneously wrote in the tag message) warnings about
undefined behavior in the SEEK_DATA/SEEK_HOLE code, and some
reshuffling of per-page block state info to fix some problems with
gfs2.
- Fix KASAN warnings due to integer overflow in SEEK_DATA/SEEK_HOLE
- Fix assertion errors when using inlinedata files on gfs2"
* tag 'iomap-5.14-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: Don't create iomap_page objects in iomap_page_mkwrite_actor
iomap: Don't create iomap_page objects for inline files
iomap: Permit pages without an iop to enter writeback
iomap: remove the length variable in iomap_seek_hole
iomap: remove the length variable in iomap_seek_data
Merge tag 'kbuild-fixes-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Restore the original behavior of scripts/setlocalversion when
LOCALVERSION is set to empty.
- Show Kconfig prompts even for 'make -s'
- Fix the combination of COFNIG_LTO_CLANG=y and CONFIG_MODVERSIONS=y
for older GNU Make versions
* tag 'kbuild-fixes-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
Documentation: Fix intiramfs script name
Kbuild: lto: fix module versionings mismatch in GNU make 3.X
kbuild: do not suppress Kconfig prompts for silent build
scripts/setlocalversion: fix a bug when LOCALVERSION is empty
Robert Richter [Thu, 15 Jul 2021 09:26:02 +0000 (11:26 +0200)]
Documentation: Fix intiramfs script name
Documentation was not changed when renaming the script in commit 80e715a06c2d ("initramfs: rename gen_initramfs_list.sh to
gen_initramfs.sh"). Fixing this.
Basically does:
$ sed -i -e s/gen_initramfs_list.sh/gen_initramfs.sh/g $(git grep -l gen_initramfs_list.sh)
Fixes: 80e715a06c2d ("initramfs: rename gen_initramfs_list.sh to gen_initramfs.sh") Signed-off-by: Robert Richter <rrichter@amd.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Kbuild: lto: fix module versionings mismatch in GNU make 3.X
When building modules(CONFIG_...=m), I found some of module versions
are incorrect and set to 0.
This can be found in build log for first clean build which shows
WARNING: EXPORT symbol "XXXX" [drivers/XXX/XXX.ko] version generation failed,
symbol will not be versioned.
But in second build(incremental build), the WARNING disappeared and the
module version becomes valid CRC and make someone who want to change
modules without updating kernel image can't insert their modules.
The problematic code is
+ $(foreach n, $(filter-out FORCE,$^), \
+ $(if $(wildcard $(n).symversions), \
+ ; cat $(n).symversions >> $@.symversions))
`foreach n` shows nothing to `cat` into $(n).symversions because
`if $(wildcard $(n).symversions)` return nothing, but actually
they do exist during this line was executed.
-rw-r--r-- 1 root root 168580 Jun 13 19:10 fs/notify/fsnotify.o
-rw-r--r-- 1 root root 111 Jun 13 19:10 fs/notify/fsnotify.o.symversions
The reason is the $(n).symversions are generated at runtime, but
Makefile wildcard function expends and checks the file exist or not
during parsing the Makefile.
Thus fix this by use `test` shell command to check the file
existence in runtime.
Rebase from both:
1. [https://lore.kernel.org/lkml/20210616080252.32046-1-lecopzer.chen@mediatek.com/]
2. [https://lore.kernel.org/lkml/20210702032943.7865-1-lecopzer.chen@mediatek.com/]
kbuild: do not suppress Kconfig prompts for silent build
When a new CONFIG option is available, Kbuild shows a prompt to get
the user input.
$ make
[ snip ]
Core Scheduling for SMT (SCHED_CORE) [N/y/?] (NEW)
This is the only interactive place in the build process.
Commit 174a1dcc9642 ("kbuild: sink stdout from cmd for silent build")
suppressed Kconfig prompts as well because syncconfig is invoked by
the 'cmd' macro. You cannot notice the fact that Kconfig is waiting
for the user input.
Use 'kecho' to show the equivalent short log without suppressing stdout
from sub-make.
scripts/setlocalversion: fix a bug when LOCALVERSION is empty
The commit 042da426f8eb ("scripts/setlocalversion: simplify the short
version part") reduces indentation. Unfortunately, it also changes behavior
in a subtle way - if the user has empty "LOCALVERSION" variable, the plus
sign is appended to the kernel version. It wasn't appended before.
This patch reverts to the old behavior - we append the plus sign only if
the LOCALVERSION variable is not set.
Fixes: 042da426f8eb ("scripts/setlocalversion: simplify the short version part") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Yang Jihong [Tue, 13 Jul 2021 11:23:58 +0000 (19:23 +0800)]
perf sched: Fix record failure when CONFIG_SCHEDSTATS is not set
The tracepoints trace_sched_stat_{wait, sleep, iowait} are not exposed to user
if CONFIG_SCHEDSTATS is not set, "perf sched record" records the three events.
As a result, the command fails.
Error: File /sys/kernel/tracing/events/sched/sched_stat_wait not found.
Hint: Perhaps this kernel misses some CONFIG_ setting to enable this feature?.
Run 'perf list' for a list of valid events
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-e, --event <event> event selector. use 'perf list' to list available events
Solution:
Check whether schedstat tracepoints are exposed. If no, these events are not recorded.
After:
# perf sched record sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.163 MB perf.data (1091 samples) ]
# perf sched report
run measurement overhead: 4736 nsecs
sleep measurement overhead: 9059979 nsecs
the run test took 999854 nsecs
the sleep test took 8945271 nsecs
nr_run_events: 716
nr_sleep_events: 785
nr_wakeup_events: 0
...
------------------------------------------------------------
Fixes: 2a09b5de235a6 ("sched/fair: do not expose some tracepoints to user if CONFIG_SCHEDSTATS is not set") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Yafang Shao <laoar.shao@gmail.com> Link: http://lore.kernel.org/lkml/20210713112358.194693-1-yangjihong1@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Yang Jihong [Thu, 15 Jul 2021 06:37:23 +0000 (14:37 +0800)]
perf probe: Fix add event failure when running 32-bit perf in a 64-bit kernel
The "address" member of "struct probe_trace_point" uses long data type.
If kernel is 64-bit and perf program is 32-bit, size of "address"
variable is 32 bits.
As a result, upper 32 bits of address read from kernel are truncated, an
error occurs during address comparison in kprobe_warn_out_range().
Before:
# perf probe -a schedule
schedule is out of .text, skip it.
Error: Failed to add events.
Solution:
Change data type of "address" variable to u64 and change corresponding
address printing and value assignment.
After:
# perf.new.new probe -a schedule
Added new event:
probe:schedule (on schedule)
Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Frank Ch. Eigler <fche@redhat.com> Cc: Ian Rogers <irogers@google.com> Cc: Jianlin Lv <jianlin.lv@arm.com> Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Li Huafei <lihuafei1@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Link: http://lore.kernel.org/lkml/20210715063723.11926-1-yangjihong1@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It's not clear why, but it causes unexplained problems in entirely
unrelated xfs code. The most likely explanation is some slab
corruption, possibly triggered due to CONFIG_SLUB_DEBUG_ON. See [1].
It ends up having a few other problems too, like build errors on
arch/arc, and Geert reporting it using much more memory on m68k [3] (it
probably does so elsewhere too, but it is probably just more noticeable
on m68k).
The architecture issues (both build and memory use) are likely just
because this change effectively force-enabled STACKDEPOT (along with a
very bad default value for the stackdepot hash size). But together with
the xfs issue, this all smells like "this commit was not ready" to me.
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One core fix for an oops which can occur if the error handling thread
fails to start for some reason and the driver is removed.
The other fixes are all minor ones in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Add missing host_lock in ufshcd_vops_setup_xfer_req()
scsi: mpi3mr: Fix W=1 compilation warnings
scsi: pm8001: Clean up kernel-doc and comments
scsi: zfcp: Report port fc_security as unknown early during remote cable pull
scsi: core: Fix bad pointer dereference when ehandler kthread is invalid
scsi: fas216: Fix a build error
scsi: core: Fix the documentation of the scsi_execute() time parameter
Merge tag '5.14-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Eight cifs/smb3 fixes, including three for stable.
Three are DFS related fixes, and two to fix problems pointed out by
static checkers"
* tag '5.14-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: do not share tcp sessions of dfs connections
SMB3.1.1: fix mount failure to some servers when compression enabled
cifs: added WARN_ON for all the count decrements
cifs: fix missing null session check in mount
cifs: handle reconnect of tcon when there is no cached dfs referral
cifs: fix the out of range assignment to bit fields in parse_server_interfaces
cifs: Do not use the original cruid when following DFS links for multiuser mounts
cifs: use the expiry output of dns_query to schedule next resolution
Merge tag 'linux-kselftest-kunit-fixes-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kunit fixes from Shuah Khan:
"Fixes to kunit tool and documentation:
- fix asserts on older python versions
- fixes to misleading error messages when TAP header format is
incorrect or when file is missing
- documentation fix: drop obsolete information about uml_abort
coverage
- remove unnecessary annotations"
* tag 'linux-kselftest-kunit-fixes-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: tool: Assert the version requirement
kunit: tool: remove unnecessary "annotations" import
Documentation: kunit: drop obsolete note about uml_abort for coverage
kunit: tool: Fix error messages for cases of no tests and wrong TAP header
Merge tag 'linux-kselftest-fixes-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan:
"A fix to memory-hotplug hot-remove test to stop spamming logs with
dump_page() entries and slowing the system down to a crawl"
* tag 'linux-kselftest-fixes-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: memory-hotplug: avoid spamming logs with dump_page(), ratio limit hot-remove error test
Merge tag 'trace-v5.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix the histogram logic from possibly crashing the kernel
Working on the histogram code, I found that if you dereference a char
pointer in a trace event that happens to point to user space, it can
crash the kernel, as it does no checks of that pointer. I have code
coming that will do this better, so just remove this ability to treat
character pointers in trace events as stings in the histogram"
* tag 'trace-v5.14-5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Do not reference char * as a string in histograms
drm/panel: ws2401: Add driver for WideChips WS2401
This adds a driver for panels based on the WideChips WS2401 display
controller. This display controller is used in the Samsung LMS380KF01
display found in the Samsung GT-I8160 (Codina) mobile phone and
possibly others.
As is common with Samsung displays manufacturer commands are necessary
to configure the display to a working state.
The display optionally supports internal backlight control, but can
also use an external backlight.
This driver re-uses the DBI infrastructure to communicate with the
display.
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The bulk of the diffstat consists of changes to our uaccess routines
so that they fall back to bytewise copying prior to reporting complete
failure when the initial (multi-byte) access faults.
However, the most disappointing change here is that we've had to bump
ARCH_DMA_MINALIGN back to 128 bytes thanks to Qualcomm's "Kryo" CPU,
which ended up in the MSM8996 mobile SoC. Still, at least we're now
aware of this design and one of the hardware designers confirmed the
L2 cacheline size for us.
Summary:
- Fix instrumentation annotations for entry code
- Ensure kernel MTE state is restored correctly on resume from suspend
- Fix MTE fault from new strlen() routine
- Fallback to byte-wise accesses on initial uaccess fault
- Bump Clang requirement for BTI
- Revert ARCH_DMA_MINALIGN back to 128 bytes (shakes fist at Qualcomm)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: entry: fix KCOV suppression
arm64: entry: add missing noinstr
arm64: mte: fix restoration of GCR_EL1 from suspend
arm64: Avoid premature usercopy failure
arm64: Restrict ARM64_BTI_KERNEL to clang 12.0.0 and newer
Revert "arm64: cache: Lower ARCH_DMA_MINALIGN to 64 (L1_CACHE_BYTES)"
arm64: Add missing header <asm/smp.h> in two files
arm64: fix strlen() with CONFIG_KASAN_HW_TAGS
Stefan Wahren [Sat, 10 Jul 2021 11:04:55 +0000 (13:04 +0200)]
ARM: multi_v7_defconfig: Make NOP_USB_XCEIV driver built-in
The usage of usb-nop-xceiv PHY on Raspberry Pi boards with BCM283x has
been a "regression source" a lot of times. The last case is breakage of
USB mass storage boot has been commit e590474768f1 ("driver core: Set
fw_devlink=on by default") for multi_v7_defconfig. As long as
NOP_USB_XCEIV is configured as module, the dwc2 USB driver defer probing
endlessly and prevent booting from USB mass storage device. So make
the driver built-in as in bcm2835_defconfig and arm64/defconfig.
The platform lost the framebuffer due to a commit solving a
circular dependency in v5.14-rc1, so add it back in by explicitly
selecting the framebuffer.
The U8500 has also gained a few systems using touchscreens from
Cypress, Melfas and Zinitix so add these at the same time as
we're updating the defconfig anyway.
This updates the Versatile Express defconfig for the changes
in the v5.14-rc1 kernel:
- The Framebuffer CONFIG_FB needs to be explicitly selected
or we don't get any framebuffer anymore. DRM has stopped to
select FB because of circular dependency.
- CONFIG_CMA options were moved around.
- CONFIG_MODULES options were moved around.
- CONFIG_CRYPTO_HW was moved around.
This updates the Versatile defconfig for the changes
in the v5.14-rc1 kernel:
- The Framebuffer CONFIG_FB needs to be explicitly selected
or we don't get any framebuffer anymore. DRM has stopped to
select FB because of circular dependency.
- The CONFIG_FB_MODE_HELPERS are not needed when using DRM
framebuffer emulation as DRM does.
- The Acorn fonts are removed, the default framebuffer font
works fine. I don't know why this was selected in the first
place or how the Kconfig was altered so it was removed.
This updates the RealView defconfig for the changes
in the v5.14-rc1 kernel:
- The Framebuffer CONFIG_FB needs to be explicitly selected
or we don't get any framebuffer anymore. DRM has stopped to
select FB because of circular dependency.
- The CONFIG_FB_MODE_HELPERS are not needed when using DRM
framebuffer emulation as DRM does.
- Drop two unused penguin logos.
This updates the Integrator defconfig for the changes
in the v5.14-rc1 kernel:
- The Framebuffer CONFIG_FB needs to be explicitly selected
or we don't get any framebuffer anymore. DRM has stopped to
select FB because of circular dependency.
- Drop the unused Matrox FB drivers that are only used with
specific PCI cards.
Merge tag 'scmi-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
ARM SCMI fixes for v5.14
A small set of fixes:
- adding check for presence of probe while registering the driver to
prevent NULL pointer access
- dropping the duplicate check as the driver core already takes care of it
- fix for possible scmi_linux_errmap buffer overflow
- fix to avoid sensor message structure padding
- fix the range check for the maximum number of pending SCMI messages
- fix for various kernel-doc warnings
* tag 'scmi-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Fix range check for the maximum number of pending messages
firmware: arm_scmi: Avoid padding in sensor message structure
firmware: arm_scmi: Fix kernel doc warnings about return values
firmware: arm_scpi: Fix kernel doc warnings
firmware: arm_scmi: Fix kernel doc warnings
firmware: arm_scmi: Fix possible scmi_linux_errmap buffer overflow
firmware: arm_scmi: Ensure drivers provide a probe function
firmware: arm_scmi: Simplify device probe function on the bus
Merge tag 'arm-ffa-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm FF-A fixes for v5.14
A small set of fixes:
- adding check for presence of probe while registering the driver to
prevent NULL pointer access
- dropping the duplicate check as the driver core already takes care of it
- fixing possible ffa_linux_errmap buffer overflow and
- fixing kernel-doc warning for comment style
* tag 'arm-ffa-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_ffa: Fix a possible ffa_linux_errmap buffer overflow
firmware: arm_ffa: Fix the comment style
firmware: arm_ffa: Simplify probe function
firmware: arm_ffa: Ensure drivers provide a probe function
Merge tag 'tegra-for-5.14-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/fixes
arm64: tegra: Device tree fixes for v5.14-rc1
This contains two late fixes for Tegra194 device tree files to restore
USB and audio functionality after enabling system-wide IOMMU support.
* tag 'tegra-for-5.14-arm64-dt-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable SMMU support for USB on Tegra194
arm64: tegra: Enable audio IOMMU support on Tegra194
Merge tag 'renesas-fixes-for-v5.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes
Renesas fixes for v5.14
- Fix a clock/reset handling design issue on the new RZ/G2L SoC,
requiring an atomic change to DT binding definitions, clock driver,
and DTS,
- Restore graphical consoles in the shmobile_defconfig.
* tag 'renesas-fixes-for-v5.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: shmobile: defconfig: Restore graphical consoles
dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions
clk: renesas: r9a07g044: Add P2 Clock support
clk: renesas: r9a07g044: Fix P1 Clock
clk: renesas: r9a07g044: Rename divider table
clk: renesas: rzg2l: Add multi clock PM support
Merge tag 'memory-controller-drv-tegra-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/fixes
Memory controller drivers for v5.14 - Tegra SoC, late fixes
Two fixes for recent series of changes in Tegra SoC memory controller
drivers:
1. Add a stub for tegra_mc_probe_device() to fix compile testing of
arm-smmu without TEGRA_MC.
2. Fix arm-smmu dtschema syntax.
* tag 'memory-controller-drv-tegra-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
dt-bindings: arm-smmu: Fix json-schema syntax
memory: tegra: Add compile-test stub for tegra_mc_probe_device()
Merge tag 'docs-5.14-2' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of fixes in and around documentation.
Some funky quotes in LICENSES/dual/CC-BY-4.0 were giving spdxcheck.py
grief; that has been fixed on both ends. Also a couple of features
updates and one docs build fix"
* tag 'docs-5.14-2' of git://git.lwn.net/linux:
docs/zh_CN: add a missing space character
Documentation/features: Add THREAD_INFO_IN_TASK feature matrix
Documentation/features: Update the ARCH_HAS_TICK_BROADCAST entry
LICENSES/dual/CC-BY-4.0: Git rid of "smart quotes"
scripts/spdxcheck.py: Strictly read license files in utf-8
Merge tag 'block-5.14-2021-07-16' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe fixes via Christoph:
- fix various races in nvme-pci when shutting down just after
probing (Casey Chen)
- fix a net_device leak in nvme-tcp (Prabhakar Kushwaha)
- Fix regression in xen-blkfront by cleaning up the removal state
machine (Christoph)
- Fix tag_set and queue cleanup ordering regression in nbd (Wang)
- Fix tag_set and queue cleanup ordering regression in pd (Guoqing)
* tag 'block-5.14-2021-07-16' of git://git.kernel.dk/linux-block:
xen-blkfront: sanitize the removal state machine
nbd: fix order of cleaning up the queue and freeing the tagset
pd: fix order of cleaning up the queue and freeing the tagset
nvme-pci: do not call nvme_dev_remove_admin from nvme_remove
nvme-pci: fix multiple races in nvme_setup_io_queues
nvme-tcp: use __dev_get_by_name instead dev_get_by_name for OPT_HOST_IFACE
Merge tag 'io_uring-5.14-2021-07-16' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Two small fixes: one fixing the process target of a check, and the
other a minor issue with the drain error handling"
* tag 'io_uring-5.14-2021-07-16' of git://git.kernel.dk/linux-block:
io_uring: fix io_drain_req()
io_uring: use right task for exiting checks
Merge tag 'drm-fixes-2021-07-16' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular rc2 fixes though a bit more than usual at rc2 stage, people
must have been testing early or else some fixes from last week got a
bit laggy.
There is one larger change in the amd fixes to amalgamate some power
management code on the newer chips with the code from the older chips,
it should only affects chips where support was introduced in rc1 and
it should make future fixes easier to maintain probably a good idea to
merge it now.
Otherwise it's mostly fixes across the board.
dma-buf:
- Fix fence leak in sync_file_merge() error code
drm/panel:
- nt35510: Don't fail on DSI reads
fbdev:
- Avoid use-after-free by not deleting current video mode
ttm:
- Avoid NULL-ptr deref in ttm_range_man_fini()
vmwgfx:
- Fix a merge commit
qxl:
- fix a TTM regression
amdgpu:
- SR-IOV fixes
- RAS fixes
- eDP fixes
- SMU13 code unification to facilitate fixes in the future
- Add new renoir DID
- Yellow Carp fixes
- Beige Goby fixes
- Revert a bunch of TLB fixes that caused regressions
- Revert an LTTPR display regression
amdkfd
- Fix VRAM access regression
- SVM fixes
i915:
- Fix -EDEADLK handling regression
- Drop the page table optimisation"
* tag 'drm-fixes-2021-07-16' of git://anongit.freedesktop.org/drm/drm: (29 commits)
drm/amdgpu: add another Renoir DID
drm/ttm: add a check against null pointer dereference
drm/i915/gtt: drop the page table optimisation
drm/i915/gt: Fix -EDEADLK handling regression
drm/amd/pm: Add waiting for response of mode-reset message for yellow carp
Revert "drm/amdkfd: Add heavy-weight TLB flush after unmapping"
Revert "drm/amdgpu: Add table_freed parameter to amdgpu_vm_bo_update"
Revert "drm/amdkfd: Make TLB flush conditional on mapping"
Revert "drm/amdgpu: Fix warning of Function parameter or member not described"
Revert "drm/amdkfd: Add memory sync before TLB flush on unmap"
drm/amd/pm: Fix BACO state setting for Beige_Goby
drm/amdgpu: Restore msix after FLR
drm/amdkfd: Allow CPU access for all VRAM BOs
drm/amdgpu/display - only update eDP's backlight level when necessary
drm/amdkfd: handle fault counters on invalid address
drm/amdgpu: Correct the irq numbers for virtual crtc
drm/amd/display: update header file name
drm/amd/pm: drop smu_v13_0_1.c|h files for yellow carp
drm/amd/display: remove faulty assert
Revert "drm/amd/display: Always write repeater mode regardless of LTTPR"
...
Merge branch 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu
Pull RCU fixes from Paul McKenney:
- fix regressions induced by a merge-window change in scheduler
semantics, which means that smp_processor_id() can no longer be used
in kthreads using simple affinity to bind themselves to a specific
CPU.
- fix a bug in Tasks Trace RCU that was thought to be strictly
theoretical. However, production workloads have started hitting this,
so these fixes need to be merged sooner rather than later.
- fix a minor printk()-format-mismatch issue introduced during the
merge window.
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
rcu: Fix pr_info() formats and values in show_rcu_gp_kthreads()
rcu-tasks: Don't delete holdouts within trc_wait_for_one_reader()
rcu-tasks: Don't delete holdouts within trc_inspect_reader()
refscale: Avoid false-positive warnings in ref_scale_reader()
scftorture: Avoid false-positive warnings in scftorture_invoker()
dt-bindings: display: renesas,du: Make resets optional on R-Car H1
The "resets" property is not present on R-Car Gen1 SoCs.
Supporting it would require migrating from renesas,cpg-clocks to
renesas,cpg-mssr.
Reflect this in the DT bindings by removing the global "required:
resets". All SoCs that do have "resets" properties already have
SoC-specific rules making it required.
The first of these leaks is caused by obj_buf never being deallocated in
__test__bpf.
This patch adds the missing free.
Signed-off-by: Riccardo Mancini <rickyman7@gmail.com> Fixes: ba1fae431e74bb42 ("perf test: Add 'perf test BPF'") Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lore.kernel.org/lkml/60f3ca935fe6672e7e866276ce6264c9e26e4c87.1626343282.git.rickyman7@gmail.com
[ Added missing stdlib.h include ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Paulo Alcantara [Fri, 16 Jul 2021 00:53:53 +0000 (21:53 -0300)]
cifs: do not share tcp sessions of dfs connections
Make sure that we do not share tcp sessions of dfs mounts when
mounting regular shares that connect to same server. DFS connections
rely on a single instance of tcp in order to do failover properly in
cifs_reconnect().
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
It turns out that the problem with the clang -Wimplicit-fallthrough
warning is not about the kernel source code, but about clang itself, and
that the warning is unusable until clang fixes its broken ways.
In particular, when you enable this warning for clang, you not only get
warnings about implicit fallthroughs. You also get this:
warning: fallthrough annotation in unreachable code [-Wimplicit-fallthrough]
which is completely broken becasue it
(a) doesn't even tell you where the problem is (seriously: no line
numbers, no filename, no nothing).
(b) is fundamentally broken anyway, because there are perfectly valid
reasons to have a fallthrough statement even if it turns out that
it can perhaps not be reached.
In the kernel, an example of that second case is code in the scheduler:
switch (state) {
case cpuset:
if (IS_ENABLED(CONFIG_CPUSETS)) {
cpuset_cpus_allowed_fallback(p);
state = possible;
break;
}
fallthrough;
case possible:
where if CONFIG_CPUSETS is enabled you actually never hit the
fallthrough case at all. But that in no way makes the fallthrough
wrong.
So the warning is completely broken, and enabling it for clang is a very
bad idea.
In the meantime, we can keep the gcc option enabled, and make the gcc
build use
-Wimplicit-fallthrough=5
which means that we will at least continue to require a proper
fallthrough statement, and that gcc won't silently accept the magic
comment versions. Because gcc does this all correctly, and while the odd
"=5" part is kind of obscure, it's documented in [1]:
"-Wimplicit-fallthrough=5 doesn’t recognize any comments as
fallthrough comments, only attributes disable the warning"
so if clang ever fixes its bad behavior we can try enabling it there again.
Link: https://gcc.gnu.org/onlinedocs/gcc/Warning-Options.html Cc: Kees Cook <keescook@chromium.org> Cc: Gustavo A. R. Silva <gustavoars@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'pwm/for-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fixes from Thierry Reding:
"A couple of fixes from Uwe that I missed for v5.14-rc1"
* tag 'pwm/for-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: ep93xx: Ensure configuring period and duty_cycle isn't wrongly skipped
pwm: berlin: Ensure configuring period and duty_cycle isn't wrongly skipped
pwm: tiecap: Ensure configuring period and duty_cycle isn't wrongly skipped
pwm: spear: Ensure configuring period and duty_cycle isn't wrongly skipped
pwm: sprd: Ensure configuring period and duty_cycle isn't wrongly skipped
Steve French [Thu, 15 Jul 2021 04:32:09 +0000 (23:32 -0500)]
SMB3.1.1: fix mount failure to some servers when compression enabled
When sending the compression context to some servers, they rejected
the SMB3.1.1 negotiate protocol because they expect the compression
context to have a data length of a multiple of 8.
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
We have a few ref counters srv_count, ses_count and
tc_count which we use for ref counting. Added a WARN_ON
during the decrement of each of these counters to make
sure that they don't go below their minimum values.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Wed, 14 Jul 2021 00:40:33 +0000 (19:40 -0500)]
cifs: fix missing null session check in mount
Although it is unlikely to be have ended up with a null
session pointer calling cifs_try_adding_channels in cifs_mount.
Coverity correctly notes that we are already checking for
it earlier (when we return from do_dfs_failover), so at
a minimum to clarify the code we should make sure we also
check for it when we exit the loop so we don't end up calling
cifs_try_adding_channels or mount_setup_tlink with a null
ses pointer.
Addresses-Coverity: 1505608 ("Derefernce after null check") Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com>
Merge tag 'Wimplicit-fallthrough-clang-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo Silva:
"This fixes many fall-through warnings when building with Clang and
-Wimplicit-fallthrough, and also enables -Wimplicit-fallthrough for
Clang, globally.
It's also important to notice that since we have adopted the use of
the pseudo-keyword macro fallthrough, we also want to avoid having
more /* fall through */ comments being introduced. Contrary to GCC,
Clang doesn't recognize any comments as implicit fall-through markings
when the -Wimplicit-fallthrough option is enabled.
So, in order to avoid having more comments being introduced, we use
the option -Wimplicit-fallthrough=5 for GCC, which similar to Clang,
will cause a warning in case a code comment is intended to be used as
a fall-through marking. The patch for Makefile also enforces this.
We had almost 4,000 of these issues for Clang in the beginning, and
there might be a couple more out there when building some
architectures with certain configurations. However, with the recent
fixes I think we are in good shape and it is now possible to enable
the warning for Clang"
* tag 'Wimplicit-fallthrough-clang-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (27 commits)
Makefile: Enable -Wimplicit-fallthrough for Clang
powerpc/smp: Fix fall-through warning for Clang
dmaengine: mpc512x: Fix fall-through warning for Clang
usb: gadget: fsl_qe_udc: Fix fall-through warning for Clang
powerpc/powernv: Fix fall-through warning for Clang
MIPS: Fix unreachable code issue
MIPS: Fix fall-through warnings for Clang
ASoC: Mediatek: MT8183: Fix fall-through warning for Clang
power: supply: Fix fall-through warnings for Clang
dmaengine: ti: k3-udma: Fix fall-through warning for Clang
s390: Fix fall-through warnings for Clang
dmaengine: ipu: Fix fall-through warning for Clang
iommu/arm-smmu-v3: Fix fall-through warning for Clang
mmc: jz4740: Fix fall-through warning for Clang
PCI: Fix fall-through warning for Clang
scsi: libsas: Fix fall-through warning for Clang
video: fbdev: Fix fall-through warning for Clang
math-emu: Fix fall-through warning
cpufreq: Fix fall-through warning for Clang
drm/msm: Fix fall-through warning in msm_gem_new_impl()
...
# perf test "88: Check open filename arg using perf trace + vfs_getname"
The third of these leaks is related to evsel->priv fields of sycalls
never being deallocated.
This patch adds the function evlist__free_syscall_tp_fields which
iterates over all evsels in evlist, matching syscalls, and calling the
missing frees.
This new function is called at the end of trace__run, right before
calling evlist__delete.
# perf test "88: Check open filename arg using perf trace + vfs_getname"
The first of these leaks is related to struct trace fields never being
deallocated.
This patch adds the function trace__exit, which is called at the end of
cmd_trace, replacing the existing deallocation, which is now moved
inside the new function.
Signed-off-by: Riccardo Mancini <rickyman7@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/de5945ed5c0cb882cbfa3268567d0bff460ff016.1626343282.git.rickyman7@gmail.com
[ Removed needless initialization to zero, missing named initializers are zeroed by the compiler ] Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
projects / kernel.git / log