Masahiro Yamada [Wed, 17 Jan 2018 16:28:01 +0000 (01:28 +0900)]
mmc: tmio: ioremap memory resource in tmio_mmc_host_alloc()
The register region is ioremap'ed in the tmio_mmc_host_probe(), i.e.
drivers cannot get access to the hardware before mmc_add_host().
Actually, renesas_sdhi_core.c reads out the CTL_VERSION register to
complete the platform-specific settings. However, at this point,
the MMC host is already running.
Move the register ioremap to tmio_mmc_host_alloc() so that drivers
can perform platform-specific settings between tmio_mmc_host_alloc()
and tmio_mmc_host_probe().
I changed tmio_mmc_host_alloc() to return an error pointer to
propagate the return code from devm_ioremap_resource().
Adrian Hunter [Tue, 9 Jan 2018 07:52:22 +0000 (09:52 +0200)]
mmc: sdhci: Rework sdhci_enable_irq_wakeups()
In preparation for adding more conditions for whether IRQ wakeup is
enabled, rework sdhci_enable_irq_wakeups() so that needed bits are added
instead of adding them all and then removing the unneeded bits.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Tue, 9 Jan 2018 07:52:21 +0000 (09:52 +0200)]
mmc: sdhci: Handle failure of enable_irq_wake()
Now that sdhci_enable_irq_wakeups() is a local function, change it to
return whether the IRQ wakeup was successfully enabled. This is in
preparation for adding more conditions for whether IRQ wakeup is enabled.
Note it is assumed, for SDHCI devices, that suspend is more important than
wakeup, so we continue to suspend regardless.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_enable_irq_wakeups() is already called by sdhci_suspend_host() so
sdhci-pci should not need to call it. However sdhci_suspend_host() only
calls it if wakeups are enabled, and sdhci-pci does not enable them until
after calling sdhci_suspend_host(). So move the calls to
sdhci_pci_init_wakeup() before calling sdhci_suspend_host(), and
stop calling sdhci_enable_irq_wakeups(). That results in some
simplification because sdhci_pci_suspend_host() and
__sdhci_pci_suspend_host() no longer need to be separate functions.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Tue, 16 Jan 2018 03:43:51 +0000 (11:43 +0800)]
mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1
Add CQHCI initialization and implement CQHCI operations for Arasan
SDHCI variant host, namely arasan,sdhci-5.1, which is used by Rockchip
RK3399 platform.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 5143c953a786 ("mmc: sdhci-esdhc-imx: Allow all supported
prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR
mode, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value if the i.MX53
eSDHCv3 is detected. According to the i.MX53 reference manual, if
DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is
eSDHCv2.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com> Reported-by: Wladimir J. van der Laan <laanwj@gmail.com> Tested-by: Wladimir J. van der Laan <laanwj@gmail.com> Fixes: 5143c953a786 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values") Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Fri, 24 Nov 2017 16:24:44 +0000 (01:24 +0900)]
mmc: tmio: use mmc_can_gpio_cd() instead of checking TMIO_MMC_USE_GPIO_CD
To use a GPIO line for card detection, TMIO_MMC_USE_GPIO_CD is set
by a legacy board (arch/sh/boards/mach-ecovec24).
For DT platforms, the "cd-gpios" property is a legitimate way for that
in case the IP-builtin card detection can not be used for some reason.
mmc_of_parse() calls mmc_gpiod_request_cd() to set up ctx->cd_gpio if
the "cd-gpios" property is specified.
To cater to both cases, mmc_can_gpio_cd() is a correct way to check
which card detection logic is used.
Andy Shevchenko [Thu, 11 Jan 2018 13:51:58 +0000 (15:51 +0200)]
sdhci: Advertise 2.0v supply on SDIO host controller
On Intel Edison the Broadcom Wi-Fi card, which is connected to SDIO,
requires 2.0v, while the host, according to Intel Merrifield TRM,
supports 1.8v supply only.
The card announces itself as
mmc2: new ultra high speed DDR50 SDIO card at address 0001
Introduce a custom OCR mask for SDIO host controller on Intel Merrifield
and add a special case to sdhci_set_power_noreg() to override 2.0v supply
by enforcing 1.8v power choice.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ard Biesheuvel [Mon, 8 Jan 2018 15:44:19 +0000 (15:44 +0000)]
mmc: sdhci_f_sdh30: add ACPI support
The Fujitsu SDH30 SDHCI controller may be described as a SCX0002 ACPI
device on ACPI platforms incorporating the Socionext SynQuacer SoC.
Given that mmc_of_parse() has already been made ACPI/DT agnostic,
making the SDH30 driver ACPI capable is actually rather simple:
all we need to do is make the call to sdhci_get_of_property() [which
does not set any properties we care about] and the clock handling
dependent on whether we are dealing with a DT device, and exposing
the ACPI id via the platform_driver struct and the module metadata.
mmc: sdhci-esdhc-imx: Enable/Disable mmc clock during runtime suspend
mmc clock can be stopped during runtime suspend and restart during runtime
resume if the sdio irq is not enabled. Stop sdio clock reduce EMI of
the device when the bus is not in use.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to return in case of error even if the actual implementation
of sdhci_runtime_suspend_host always return 0. We don't want to
power down the clock and the assuption is that the sdhci_runtime_suspend_host
always let the system consistent in case of failure
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Atul Garg [Thu, 4 Jan 2018 04:17:36 +0000 (20:17 -0800)]
mmc:host:sdhci-pci:Addition of Arasan PCI Controller with integrated phy.
The Arasan Controller is based on a FPGA platform and has integrated phy
with specific registers used during initialization and
management of different modes. The phy and the controller are integrated
and registers are very specific to Arasan.
Arasan being an IP provider, licenses these IPs to various companies for
integration of IP in custom SOCs. The custom SOCs define own register
map depending on how bits are tied inside the SOC for phy registers,
depending on SOC memory plan and hence will require own platform drivers.
If more details on phy registers are required, an interface document is
hosted at https://arasan.com/NF/eMMC5.1 PHY Programming in Linux.pdf.
Arnd Bergmann [Wed, 3 Jan 2018 22:49:18 +0000 (23:49 +0100)]
mmc: s3mci: mark debug_regs[] as static
The global array clashes with a newly added symbol of the same name:
drivers/staging/ccree/cc_debugfs.o:(.data+0x0): multiple definition of `debug_regs'
drivers/mmc/host/s3cmci.o:(.data+0x70): first defined here
We should fix both, this one addresses the s3cmci driver by removing
the symbol from the global namespace. While at it, this separates
the declaration from the type definition and makes the variable const.
Fixes: 9bdd203b4dc8 ("s3cmci: add debugfs support for examining driver and hardware state") Fixes: b3ec9a6736f2 ("staging: ccree: staging: ccree: replace sysfs by debugfs interface") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Tue, 19 Dec 2017 13:34:03 +0000 (14:34 +0100)]
mmc: tmio: use io* accessors consistently
Because we started using io*_rep accessors previously because they are
more widely defined across architectures, let's be consistent and use
this family for all accessor wrappers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Zhoujie Wu [Mon, 18 Dec 2017 22:38:47 +0000 (14:38 -0800)]
mmc: sdhci-xenon: wait 5ms after set 1.8V signal enable
According to SD spec 3.00 3.6.1 signal voltage switch
procedure step 6~8,
(6) Set 1.8V Signal Enable in the Host Control 2 register.
(7) Wait 5ms. 1.8V voltage regulator shall be stable within this period.
(8) If 1.8V Signal Enable is cleared by Host Controller, go to step (12).
Host should wait 5ms after set 1.8V signal enable bit in
Host Control 2 register and check if 1.8V is stable or not.
But current code checks this bit right after set it.
On some platforms with xenon controller found the bit is
cleared right away and host reports "1.8V regulator output
did not became stable" and 5ms delay can help.
Implement voltage_switch callback for xenon controller to add 5ms
delay to make sure the 1.8V signal enable bit is set by controller.
Masahiro Yamada [Fri, 24 Nov 2017 16:24:47 +0000 (01:24 +0900)]
mmc: tmio, renesas_sdhi: move struct tmio_mmc_dma to renesas_sdhi.h
struct tmio_mmc_dma looks like TMIO core data, but in fact, Renesas
private data. Move it to renesas_sdhi.h (probably, it is better to
rename it to renesas_sdhi_dma, or squash it into struct renesas_sdhi).
I also moved struct renesas_sdhi and host_to_priv() to that header
because they are necessary to convert the tmio_mmc_host pointer into
the renesas_sdhi pointer.
Daniel Drake [Tue, 12 Dec 2017 10:49:02 +0000 (10:49 +0000)]
mmc: avoid removing non-removable hosts during suspend
The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.
After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.
The conditions here are:
1. During suspend, we reach mmc_pm_notify()
2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
-ENOSYS because btsdio_driver does not have a suspend method.
3. mmc_pm_notify() proceeds to remove the card
4. Upon resume, mmc_rescan() does nothing with this host, because of
the rescan_entered check which aims to only scan a non-removable
device a single time (i.e. during boot).
Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.
Signed-off-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Fri, 24 Nov 2017 16:24:43 +0000 (01:24 +0900)]
mmc: tmio: move mmc_gpio_request_cd() before mmc_add_host()
Drivers do not need to call mmc_gpiod_request_cd_irq() explicitly
because mmc_start_host() calls it. To make it work, cd_gpio must
be set before mmc_add_host().
Masahiro Yamada [Fri, 24 Nov 2017 16:24:41 +0000 (01:24 +0900)]
mmc: tmio: move mmc_host_ops to struct tmio_mmc_host from static data
Currently, tmio_mmc_ops is static data and tmio_mmc_host_probe()
updates some hooks in the static data. This is a problem when
two or more instances call tmio_mmc_host_probe() and each of them
requests to use its own card_busy/start_signal_voltage_switch.
We can borrow a solution from sdhci_alloc_host(). Copy the whole
ops structure to host->mmc_host_ops, then override the hooks in
malloc'ed data. Constify tmio_mmc_ops since it is now a template
ops used by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Masahiro Yamada [Fri, 24 Nov 2017 16:24:39 +0000 (01:24 +0900)]
mmc: tmio: set tmio_mmc_host to driver data
The remove, suspend, resume hooks need to get tmio_mmc_host. It is
tedious to call mmc_priv() to convert mmc_host to tmio_mmc_host.
We can directly set tmio_mmc_host to driver data.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com> Fixes: 9d08428afb72 ("mmc: renesas-sdhi: make renesas_sdhi_sys_dmac main module file") Cc: <stable@vger.kernel.org> # v4.13+
[Shimoda: Added Fixes tag and Cc to the stable ML] Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Sean Wang [Thu, 7 Dec 2017 06:43:22 +0000 (14:43 +0800)]
mmc: dt-bindings: add mmc support to MT7623 SoC
Add the devicetree binding for MT7623 SoC using MT2701 as the fallback.
Cc: devicetree@vger.kernel.org Signed-off-by: Sean Wang <sean.wang@mediatek.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Christoph Fritz [Sat, 9 Dec 2017 22:47:55 +0000 (23:47 +0100)]
mmc: core: apply NO_CMD23 quirk to some specific cards
To get an usdhc Apacer and some ATP SD cards work reliable, CMD23 needs
to be disabled. This has been tested on i.MX6 (sdhci-esdhc) and rk3288
(dw_mmc-rockchip).
Dan Carpenter [Fri, 8 Dec 2017 11:55:16 +0000 (14:55 +0300)]
mmc: block: blk-mq: Potential NULL deref on mmc_blk_alloc_req() failure
mmc_blk_alloc_req() is supposed to return error pointers but there is
one path where we forget to set the error code and accidentally return
NULL. The callers are not expecting that and will have a NULL pointer
dereference.
Fixes: 41e3efd07d5a ("mmc: block: Simplify cleaning up the queue") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
yinbo.zhu [Fri, 1 Dec 2017 07:09:34 +0000 (15:09 +0800)]
mmc: sdhci-of-esdhc: fix the mmc error after sleep on ls1046ardb
When system wakes up from sleep on ls1046ardb, the SD operation fails
with mmc error messages since ESDHC_TB_EN bit couldn't be cleaned by
eSDHC_SYSCTL[RSTA]. It's proper to clean this bit in esdhc_reset()
rather than in probe.
Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com> Acked-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Fri, 1 Dec 2017 12:55:31 +0000 (14:55 +0200)]
mmc: mmc_test: Ensure command queue is disabled for testing
mmc_test disables the command queue because none of the tests use the
command queue. However the Reset Test will re-enable it, so disable it in
that case too.
Fixes: 9d4579a85c84 ("mmc: mmc_test: Disable Command Queue while mmc_test is used") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Fri, 1 Dec 2017 12:55:30 +0000 (14:55 +0200)]
mmc: core: Ensure cmd_completion is initialized
mmc_test now uses mmc_start_request() to test sending commands during
"ongoing" asynchronous transfers, i.e. tests:
Commands during non-blocking read - use Set Block Count (CMD23)
Commands during non-blocking write - use Set Block Count (CMD23)
mmc_start_request() was not initializing cmd_completion, but cmd_completion
is used by "ongoing" transfers, so move initialization of cmd_completion
into making mmc_start_request().
Fixes: cb39f61e9b1e ("mmc: core: Export a few functions needed for blkmq support") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400
This patch supports HS400 for AMD upcoming emmc 5.0 controller.The
HS400 and HS200 mode requires hardware work around also. This patch
adds the quirks for the same.
Signed-off-by: Nehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Arnd Bergmann [Mon, 27 Nov 2017 11:53:22 +0000 (12:53 +0100)]
mmc_test: use ktime_get_ts64 for timestamps
Calling getnstimeofday() can suffer from time jumps and from the
y2038 overflow, so it is not appropriate here. Using ktime_get_ts64()
solves both problems. Using ktime_get() with ktime_t timestamps would
also work, but it seems that we mainly want to print the times as
seconds+nanoseconds, so it would require an extra division in the output.
Colin Ian King [Thu, 30 Nov 2017 11:37:38 +0000 (11:37 +0000)]
mmc: block: make function mmc_cqe_issue_type static
The function mmc_cqe_issue_type is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/mmc/core/queue.c:62:21: warning: symbol 'mmc_cqe_issue_type'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Wed, 29 Nov 2017 13:41:15 +0000 (15:41 +0200)]
mmc: block: blk-mq: Stop using legacy recovery
There are only a few things the recovery needs to do. Primarily, it just
needs to:
Determine the number of bytes transferred
Get the card back to transfer state
Determine whether to retry
There are also a couple of additional features:
Reset the card before the last retry
Read one sector at a time
The legacy code spent much effort analyzing command errors, but commands
fail fast, so it is simpler just to give all command errors the same number
of retries.
Adrian Hunter [Wed, 29 Nov 2017 13:41:14 +0000 (15:41 +0200)]
mmc: block: Reduce polling timeout from 10 minutes to 10 seconds
Set a 10 second timeout for polling write request busy state. Note, mmc
core is setting a 3 second timeout for SD cards, and SDHCI has long had a
10 second software timer to timeout the whole request, so 10 seconds should
be ample.
Adrian Hunter [Wed, 29 Nov 2017 13:41:13 +0000 (15:41 +0200)]
mmc: block: Add timeout_clks when calculating timeout
According to the specification, total access time is derived from both TAAC
and NSAC, which means the timeout should add both timeout_ns and
timeout_clks. Host drivers do that, so make the block driver do that too.
Adrian Hunter [Wed, 29 Nov 2017 13:41:12 +0000 (15:41 +0200)]
mmc: block: Check for transfer state in card_busy_detect()
The card is required to return to transfer state. Since that is the state
required to start another transfer, check for that state instead of
programming state.
Adrian Hunter [Wed, 29 Nov 2017 13:41:07 +0000 (15:41 +0200)]
mmc: block: blk-mq: Add support for direct completion
For blk-mq, add support for completing requests directly in the ->done
callback. That means that error handling and urgent background operations
must be handled by recovery_work in that case.
Adrian Hunter [Wed, 29 Nov 2017 13:41:04 +0000 (15:41 +0200)]
mmc: block: Add CQE support
Add CQE support to the block driver, including:
- optionally using DCMD for flush requests
- "manually" issuing discard requests
- issuing read / write requests to the CQE
- supporting block-layer timeouts
- handling recovery
- supporting re-tuning
CQE offers 25% - 50% better random multi-threaded I/O. There is a slight
(e.g. 2%) drop in sequential read speed but no observable change to sequential
write.
CQE automatically sends the commands to complete requests. However it only
supports reads / writes and so-called "direct commands" (DCMD). Furthermore
DCMD is limited to one command at a time, but discards require 3 commands.
That makes issuing discards through CQE very awkward, but some CQE's don't
support DCMD anyway. So for discards, the existing non-CQE approach is
taken, where the mmc core code issues the 3 commands one at a time i.e.
mmc_erase(). Where DCMD is used, is for issuing flushes.
Adrian Hunter [Wed, 29 Nov 2017 13:41:03 +0000 (15:41 +0200)]
mmc: block: Add blk-mq support
Define and use a blk-mq queue. Discards and flushes are processed
synchronously, but reads and writes asynchronously. In order to support
slow DMA unmapping, DMA unmapping is not done until after the next request
is started. That means the request is not completed until then. If there is
no next request then the completion is done by queued work.
Adrian Hunter [Wed, 29 Nov 2017 13:41:02 +0000 (15:41 +0200)]
mmc: core: Add parameter use_blk_mq
Until mmc has blk-mq support fully implemented and tested, add a parameter
use_blk_mq, set to true if config option MMC_MQ_DEFAULT is selected, which
it is by default.
Adrian Hunter [Wed, 29 Nov 2017 13:40:59 +0000 (15:40 +0200)]
mmc: block: Simplify cleaning up the queue
Use blk_cleanup_queue() to shutdown the queue when the driver is removed,
and instead get an extra reference to the queue to prevent the queue being
freed before the final mmc_blk_put().
Wolfram Sang [Tue, 14 Nov 2017 22:55:20 +0000 (23:55 +0100)]
mmc: core: use usleep_range rather than HZ magic in mmc_delay()
Documentation/timers/timers-howto.txt recommends to use usleep_range for
delays 1-20ms. Let's adhere to it. No need for messing with HZ and still
do busy looping these days.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
yinbo.zhu [Wed, 8 Nov 2017 09:09:50 +0000 (17:09 +0800)]
mmc: sdhci-of-esdhc: fix eMMC couldn't work after kexec
The bit eSDHC_TBCTL[TB_EN] couldn't be reset by eSDHC_SYSCTL[RSTA] which is
used to reset for all. The driver should make sure it's cleared before card
initialization, otherwise the initialization would fail.
Jiri Slaby [Thu, 30 Nov 2017 14:35:44 +0000 (15:35 +0100)]
futex: futex_wake_op, fix sign_extend32 sign bits
sign_extend32 counts the sign bit parameter from 0, not from 1. So we
have to use "11" for 12th bit, not "12".
This mistake means we have not allowed negative op and cmp args since
commit 30d6e0a4190d ("futex: Remove duplicated code and fix undefined
behaviour") till now.
Fixes: 30d6e0a4190d ("futex: Remove duplicated code and fix undefined behaviour") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Darren Hart <dvhart@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 10 Dec 2017 16:30:04 +0000 (08:30 -0800)]
Merge tag 'for-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"This contains a few fixes (error handling, quota leak, FUA vs
nobarrier mount option).
There's one one worth mentioning separately - an off-by-one fix that
leads to overwriting first byte of an adjacent page with 0, out of
bounds of the memory allocated by an ioctl. This is under a privileged
part of the ioctl, can be triggerd in some subvolume layouts"
* tag 'for-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Fix possible off-by-one in btrfs_search_path_in_tree
Btrfs: disable FUA if mounted with nobarrier
btrfs: fix missing error return in btrfs_drop_snapshot
btrfs: handle errors while updating refcounts in update_ref_for_cow
btrfs: Fix quota reservation leak on preallocated files
Linus Torvalds [Sun, 10 Dec 2017 16:26:59 +0000 (08:26 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
- A revert of all SCPI changes from the 4.15 merge window. They had
regressions on the Amlogic platforms, and the submaintainer isn't
around to fix these bugs due to vacation, etc. So we agreed to revert
and revisit in next release cycle.
- A series fixing a number of bugs for ARM CCN interconnect, around
module unload, smp_processor_id() in preemptable context, and fixing
some memory allocation failure checks.
- A handful of devicetree fixes for different platforms, fixing
warnings and errors that were previously ignored by the compiler.
- The usual set of mostly minor fixes for different platforms.
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM64: dts: meson-gx: fix UART pclk clock name
ARM: omap2: hide omap3_save_secure_ram on non-OMAP3 builds
arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
ARM: dts: Fix dm814x missing phy-cells property
ARM: dts: Fix elm interrupt compiler warning
bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
bus: arm-cci: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Simplify code
bus: arm-ccn: Check memory allocation failure
bus: arm-ccn: constify attribute_group structures.
firmware: arm_scpi: Revert updates made during v4.15 merge window
arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
arm64: dts: sort vendor subdirectories in Makefile alphabetically
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
MAINTAINERS: exclude other Socionext SoC DT files from ARM/UNIPHIER entry
arm64: dts: uniphier: remove unnecessary interrupt-parent
...
Linus Torvalds [Sun, 10 Dec 2017 16:24:16 +0000 (08:24 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- A number of issues in the vgic discovered using SMATCH
- A bit one-off calculation in out stage base address mask (32-bit
and 64-bit)
- Fixes to single-step debugging instructions that trap for other
reasons such as MMMIO aborts
- Printing unavailable hyp mode as error
- Potential spinlock deadlock in the vgic
- Avoid calling vgic vcpu free more than once
- Broken bit calculation for big endian systems
s390:
- SPDX tags
- Fence storage key accesses from problem state
- Make sure that irq_state.flags is not used in the future
x86:
- Intercept port 0x80 accesses to prevent host instability (CVE)
- Use userspace FPU context for guest FPU (mainly an optimization
that fixes a double use of kernel FPU)
- Do not leak one page per module load
- Flush APIC page address cache from MMU invalidation notifiers"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
KVM: x86: fix APIC page invalidation
KVM: s390: Fix skey emulation permission check
KVM: s390: mark irq_state.flags as non-usable
KVM: s390: Remove redundant license text
KVM: s390: add SPDX identifiers to the remaining files
KVM: VMX: fix page leak in hardware_setup()
KVM: VMX: remove I/O port 0x80 bypass on Intel hosts
x86,kvm: remove KVM emulator get_fpu / put_fpu
x86,kvm: move qemu/guest FPU switching out to vcpu_run
KVM: arm/arm64: Fix broken GICH_ELRSR big endian conversion
KVM: arm/arm64: kvm_arch_destroy_vm cleanups
KVM: arm/arm64: Fix spinlock acquisition in vgic_set_owner
kvm: arm: don't treat unavailable HYP mode as an error
KVM: arm/arm64: Avoid attempting to load timer vgic state without a vgic
kvm: arm64: handle single-step of hyp emulated mmio instructions
kvm: arm64: handle single-step during SError exceptions
kvm: arm64: handle single-step of userspace mmio instructions
kvm: arm64: handle single-stepping trapped instructions
KVM: arm/arm64: debug: Introduce helper for single-step
arm: KVM: Fix VTTBR_BADDR_MASK BUG_ON off-by-one
...
Olof Johansson [Sun, 10 Dec 2017 04:23:29 +0000 (20:23 -0800)]
Merge tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: fix UART pclk clock name
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
Olof Johansson [Sun, 10 Dec 2017 04:22:46 +0000 (20:22 -0800)]
Merge tag 'ccn/fixes-for-4.15' of git://git.linaro.org/people/pawel.moll/linux into fixes
bus: ARM CCN and CCI PMU driver fixes
This is a bunch of fixes CCN and (guest starring this time) CCI drivers.
* Check for potential of failed allocation for the driver name string
* Manage CPU ID properly at allocation (both CCN and CCI)
* Fix module unload warnings related to objects release order
* Small improvements like using allocating printfs and proper
attributes constification
The one fixing potential issues have been cc-ed to stable.
* tag 'ccn/fixes-for-4.15' of git://git.linaro.org/people/pawel.moll/linux:
bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
bus: arm-cci: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
bus: arm-ccn: Simplify code
bus: arm-ccn: Check memory allocation failure
bus: arm-ccn: constify attribute_group structures.